Some versions of MCFW do not support the MC_CMD_VADAPTOR_SET_MAC
command, and ENOSYS will be returned.
If the PF created its own vport, the function's datapath must be
stopped and the vport can be reconfigured to reflect the new MAC
address.
If the MCFW created the vport for the PF (which is the case when
the nic_data->vport_mac is blank), nothing further needs to be
done as the vport is not under the control of the PF.
This only applies to PFs because the MCFW in question does not
support VFs.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-organize the structure of error handling to avoid having
to duplicate the netif_err() around the ifdefs.
The only change to the behaviour of the error-handling is that
the PF's data structure to record VF details should only be
updated if the original command succeeded.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If any VF is assigned as the PF is unloaded, do not attempt to
remove its vport or the vswitch. These will be removed if the
driver binds to the PF again, as an entity reset occurs during
probe.
A 'force' flag is added to efx_ef10_pci_sriov_disable() to
distinguish between disabling SR-IOV and driver unload.
SR-IOV cannot be disabled if VFs are assigned to guests.
If the PF driver is unloaded while VFs are assigned, the driver
may try to bind to the VF again at a later point if the driver
has been reloaded and the VF returns to the same domain as the PF.
In this case, the PF will not have a VF data structure, so the VF
can check this and drop out of probe early.
In this case, efx->vf_count will be zero but VFs will be present.
The user is advised to remove the VF and re-create it. The check
at the beginning of efx_ef10_pci_sriov_disable() that
efx->vf_count is non-zero is removed to allow SR-IOV to be
disabled in this case. Also, if the PF driver is unloaded, it
will disable SR-IOV to remove these unknown VFs.
By not disabling bus-mastering if VFs are still assigned, the VF
will continue to pass traffic after the PF has been removed.
When using the max_vfs module parameter, if VFs are already
present do not try to initialise any more.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ifenslave command to set up a bond runs in an atomic
context, and it queries the stats on the devices that are
being enslaved. A VF needs to make an MCDI call to update
its stats, which is not allowed in atomic context.
The releasing of the stats_lock is moved to the beginning of
the VF stats update function so that in_interrupt() can be
used; it must be taken again before returning from this
function.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The raw_mask array is not initialised, so it needs to be
explicitly set to zero in the 'else' branch.
If the EVB capability is not present, a port cannot have multiple
functions so the per-port MAC stats are correct and should match
the corresponding vadaptor stats, so this redundancy can be
removed from the ethtool stats output.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MC_CMD_MAC_STATS can be called on a function before a
vadaptor has been created, as the kernel can call into this
through ndo_get_stats/ndo_get_stats64.
If MC_CMD_MAC_STATS is called before the DMA queues have been
setup, so that a vadaptor has not been created yet, firmware
will return ENOENT. This is expected, so suppress the MCDI
error message in this case.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdevice statistics (in /proc/net/dev) are per-function
stats so they must use the vadaptor stats. Change the use of
MAC stats to vadaptor stats, and remove any statistics that
can only be measured per-port. All stats that are removed
will be shown as zeroes when these statistics are displayed.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware does not support a periodic DMA of vadaptor-stats
on VFs, so only update the stats buffer when stats are
requested (when running "ethtool -S" or an ip/ifconfig
command that reports stats).
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All interfaces will display vadaptor statistics, so set all the
relevant bits in the stats bitmask. Only functions with the
LINKCTRL flag will see other stats, including (per-port) MAC stats.
The vadaptor stats are from rx_unicast to tx_overflow.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC stats are per-port and will only be displayed on the PF
with control of the link (one per physical port). Vadapter stats
will also be displayed for this PF, so distinguish the MAC stats
by adding a prefix of "port_".
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On every adapter there will be one primary PF per adaptor and
one link control PF per port.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is a stylistic change and does not affect
functionality.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where we have multiple functions (PFs and VFs), this
sysfs entry is useful to identify the physical port corresponding
to the function we are interested in.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCDI tracing is conditional on CONFIG_SFC_MCDI_LOGGING, which is enabled
by default.
Each MCDI command will produce a console line like
sfc dom🚌dev:fn ifname: MCDI RPC REQ: xxxxxxxx [yyyyyyyy...]
where xxxxxxxx etc. are the raw MCDI payload in 32-bit hex chunks.
The response will then produce a similar line with "RESP" instead of "REQ",
and containing the MCDI response payload (if any).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a set_mac_address() NIC-type function for EF10 only, and
use this to set the MAC address on the vadaptor. For Siena and
earlier, the MAC address continues to be set by MC_CMD_SET_MAC;
this is still called on EF10, and including a MAC address in
this command has no effect.
The sriov_mac_address_changed() NIC-type function is no longer
needed on EF10, but it is needed for Siena where it is used to
update the peer address of the PF for VFDI. Change this to use
the new set_mac_address function pointer.
efx_ef10_sriov_mac_address_changed() is no longer called, as VFs
will try to change the MAC address on their vadaptor rather than
trying to change to the context of the PF to alter the vport.
When a VF is running in direct passthrough mode with MAC spoofing
enabled, it will be able to change the MAC address on its vadaptor.
In this case, there is a link to the PF, so find the correct VF in
its ef10_vf array and update the MAC address.
ndo_set_mac_address() can be called during driver unload while
bonding, and in this case the device has already been stopped, so
don't call efx_net_open() to restart it after reconfiguration.
efx->port_enabled is set to false in efx_stop_port(), so it is
indicator of whether the device needs to be restarted.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exercised with
"ip link set <PF intf> vf <vf_i> state {auto|enable|disable}"
Sets the reporting policy for VF link state to either
- mirror physical link state
- always up
- always down
get VF link state mode in efx_ef10_sriov_get_vf_config
Exercised by
"ip link show <PF intf>";
output will include a line like
vf 0 MAC 12:34:56:78:9a:bc, link-state auto
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we do an entity reset when we detect an MC reboot.
This messes up SRIOV because it leaves VFs orphaned. The extra
reset is rather redundant anyway, since the MC reboot will have
basically reset everything.
This change replaces the entity reset after MC reboot with a
simpler datapath reset that reallocates resources but doesn't
perform the entity reset.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid MC bugs the flags field needs to be set to 0.
Instead of explicitly clearing out the flags individually, a
better way to do this is to memset the MCDI_BUF to 0.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A VF's MAC address is set by its parent PF and added to its vport.
To get this MAC address, the VF must use MC_CMD_ VPORT_GET_MAC_ADDRESSES.
In the current scheme, a VF's vport should only have one MAC address,
so warn if this is not the case.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If MCDI timeouts are encountered during efx_ef10_filter_table_remove(),
an FLR will be queued, but efx->filter_state will still be kfree()d.
The queued FLR will then call efx_ef10_filter_table_restore(), which
will try to use efx->filter_state. This previously caused a panic.
This patch adds an rwsem to protect the existence of efx->filter_state,
separately from the spinlock protecting its contents. Users which can
race against efx_ef10_filter_table_remove() should down_read this rwsem.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialised in efx_probe_vf and removal is dealt with in
efx_ef10_remove.
vf->efx is needed in future patches to change the MAC address
of the VF via the parent PF, while the driver is bound to the
VF.
Example: ip link set dev vf NUM mac LLADDR
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added function efx_ef10_get_vf_index to store the vf_index
in nic_data during probe
vf_index is needed in future patches to access a particular
VF in the VF data structure.
Moved efx_ef10_probe_pf and efx_ef10_probe_vf in order to
used efx_ef10_remove
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MC_CMD_SET_MAC is privileged and can only by called by the link
control function.
This patch adds efx_ef10_mac_reconfigure_vf which avoids the call
to MC_CMD_SET_MAC by the Virtual function
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the device ID of the VF to the PCI device ID table.
Added a boolean flag is_vf in efx_nic_type to differentiate
between a VF and PF at probe time. This flag is useful in later
patches while setting MAC address specially in the
PCI-passthrough case.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow PFs to allocate shared RSS contexts if we exhaust our
exclusive RSS contexts. Make VFs use shared RSS contexts in
all cases.
Spruce up error handling so that the shadow copy of the RSS
table is updated after successful update, rather than in all
cases, so that we report the actual contents of the RSS table
after a failure to set it, rather than what we'd like it to be.
Populate context_size parameter when vacuously allocating RSS
context of size 1.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Accept EPERM in some simple cases, the following cases are handled:
1) efx_mcdi_read_assertion()
Unprivileged PCI functions aren't allowed to GET_ASSERTS.
We return success as it's up to the primary PF to deal with asserts.
2) efx_mcdi_mon_probe() in efx_ef10_probe()
Unprivileged PCI functions aren't allowed to read sensor info, and
worrying about sensor data is the primary PF's job.
3) phy_op->reconfigure() in efx_init_port() and efx_reset_up()
Unprivileged functions aren't allowed to MC_CMD_SET_LINK, they just have
to accept the settings (including flow-control, which is what
efx_init_port() is worried about) they've been given.
4) Fallback to GET_WORKAROUNDS in efx_ef10_probe()
Unprivileged PCI functions aren't allowed to set workarounds. So if
efx_mcdi_set_workaround() fails EPERM, use efx_mcdi_get_workarounds()
to find out if workaround_35388 is enabled.
5) If DRV_ATTACH gets EPERM, try without specifying fw-variant
Unprivileged PCI functions have to use a FIRMWARE_ID of 0xffffffff
(MC_CMD_FW_DONT_CARE).
6) Don't try to exit_assertion unless one had fired
Previously we called efx_mcdi_exit_assertion even if
efx_mcdi_read_assertion had received MC_CMD_GET_ASSERTS_FLAGS_NO_FAILS.
This is unnecessary, and the resulting MC_CMD_REBOOT, even if the
AFTER_ASSERTION flag made it a no-op, would fail EPERM for unprivileged
PCI functions.
So make efx_mcdi_read_assertion return whether an assert happened, and only
call efx_mcdi_exit_assertion if it has.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to use MC_CMD_VADAPTOR_SET_MAC, vadaptors must be
manually allocated and freed as automatic vadaptors will disappear
when their reference_count reaches zero, which must happen before
the MAC address is changed.
Vadaptors are allocated and freed in the vswitching_probe/remove
functions for PFs and VFs, and this means that vadaptors are restored
correctly following an MC reboot or other reset when required.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added efx_nic_type structure for VF.
Mapped a different BAR for VF as it uses BAR 0 for memory.
Added functions sriov_init and sriov_fini.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use MC_CMD_GET_FUNCTION_INFO to record the PF number in nic_data.
This will be needed when assigned vports to VFs.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds functions to allocate and free vswitches and vports; vadaptors
are automatically allocated and freed when TX/RX queues are
initialised and finalised. This vswitching structure is only created
if the firmware supports it, so a check that full-featured firmware
is running is performed first.
If the MC resets, the vswitching infrastructure will need to be
recreated, so mark the "must_probe_vswitching" flag when an MC reboot
is detected.
Don't try to create a vswitch if vf-count=0
This allocation of vswitches and vports does not currently support
configuring VLAN tags, but that can be added in a future change.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default port ID of EVB_PORT_ID_ASSIGNED is a "magic" number
for the MCFW to select the physical port of the PF. If other
vswitches and vports are created on top of the default firmware
configuration, the ID of the newly created vport is then required
when passed to MCDI commands. Currently, this doesn't happen so
the vport_id is never changed, but a subsequent patch will change
this behaviour so that other vswitches and vports are created.
The vport_id recorded in nic_data is only relevant for PFs.
VFs will have their vports created by their parent PF, and in
that case the parent PF will record the vport ID of each VF.
For a VF, nic_data->vport_id is expected to remain at the default
value.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The (future) code to add/remove vswitches and vports will be
dependent on the firmware variant.
To simplify the checking of the firmware variant, record
values for rx_dpcpu_fw_id and tx_dpcpu_fw_id in EF10 nic_data.
There was only one place where this was previously used:
efx_mcdi_print_fwver() in ethtool.c.
The MC_CMD_GET_CAPABILITIES can be replaced and the values from
nic_data used instead.
Note that the printing of "?" if the MC command fails or if the
outlength is incorrect no longer apply, because errors are returned
in efx_ef10_init_datapath_caps() in both of these cases.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX_DOMAIN field is currently reserved but its safer to set
it to 0 for future compatibility.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the use of sriov_configure on EF10
to enable Virtual Functions while the driver is loaded.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By putting all the efx_{siena,ef10}_sriov_* declarations in
{siena,ef10}_sriov.h, ensure they cannot be called from nic-generic code.
Also fixes up an instance of this, where mcdi.c was calling
efx_siena_sriov_flr.
The single instance of netdev_ops should call general high level
functions that can then call something adapter specific in efx_nic_type.
We should only do adapter specialisation via efx_nic_type.
Removal of sriov functionality from the Falcon code means that tests
are needed for the presence of some callbacks.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also add dummy functions where required to avoid NULL pointer dereference.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_ef10_probe() was BUGging out if the BAR2 size was 0. This is
unnecessarily violent; instead we should just fail to probe the device.
Kept a WARN_ON as this problem indicates a broken or misconfigured NIC.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a counter rx_noskb_drop for failure to allocate an skb.
Summed the per-channel rx_nodesc_trunc counters earlier so that they can
be included in rx_dropped.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MCDI command times out (whether or not we find it
completed when we poll), call efx_mcdi_abandon(), which tells
all subsequent MCDI calls to fail-fast, and queues up an FLR.
Because an FLR doesn't lead to receiving any reboot even from
the MC (unlike most other types of reset), we have to call
efx_ef10_reset_mc_allocations.
In efx_start_all(), if a reset (of any kind) is pending, we
bail out.
Without this, attempts to reconfigure (e.g. change mtu) can
cause driver/mc state inconsistency if the first MCDI call
triggers an FLR.
For similar reasons, on EF10, in
efx_reset_down(method=RESET_TYPE_MCDI_TIMEOUT), set the number
of active queues to zero before calling efx_stop_all().
And, on farch, in efx_reset_up(method=RESET_TYPE_MCDI_TIMEOUT),
set active_queues and flushes pending & outstanding to zero.
efx_mcdi_mode_{poll,event}() should not take us out of fail-fast
mode. Instead, this is done by efx_mcdi_reset() after the FLR
completes.
The new FLR reset_type RESET_TYPE_MCDI_TIMEOUT doesn't really
fit into the hierarchy of reset 'scopes' whereby efx_reset()
decides some resets subsume others. Thus, it uses separate logic.
Also, fixed up some inconsistency around RESET_TYPE_MC_BIST,
which was in the wrong place in that hierarchy.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the "separate_tx_channels=1" module parameter, the TX queues are
initially numbered starting from the first TX-only channel number (after all the
RX-only channels). efx_set_channels() renumbers the queues so that they are
indexed from zero.
On EF10, the TX queues need to be relabelled in this way before calling the
dimension_resources NIC type operation, otherwise the TX queue PIO buffers can be
linked to the wrong VIs when using "separate_tx_channels=1".
Added comments to explain UC/WC mappings for PIO buffers
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Faster than memcpy/memset on some architectures.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EF10 implements option descriptors to switch TX checksum offload
on and off between packets. We could therefore use a single
hardware TX queue per kernel TX queue, although we don't yet.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PORT_RESET MC command was NOP in the ef10 firmware hence we are using
ENTITY_RESET to make sure all resource allocations are reset.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we insert an filter, the firmware checks that the given RX queue
index is in range even if it will not be used. In case we're
inserting a drop filter, pass the value 0.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The operation can now fail, so change its return type to int.
Remove the inline wrapper while we're changing the signature.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Daniel Pieczko
Shradha Shah
Edward Cree
Jon Cooper
David S. Miller
Eric W. Biederman
Ben Hutchings