[ Upstream commit 5903123f66 ]
When setting RTO through BPF program, some SYN ACK packets were unaffected
and continued to use TCP_TIMEOUT_INIT constant. This patch adds timeout
option to struct request_sock. Option is initialized with TCP_TIMEOUT_INIT
and is reassigned through BPF using tcp_timeout_init call. SYN ACK
retransmits now use newly added timeout option.
Signed-off-by: Akhmat Karakotov <hmukos@yandex-team.ru>
Acked-by: Martin KaFai Lau <kafai@fb.com>
v2:
- Add timeout option to struct request_sock. Do not call
tcp_timeout_init on every syn ack retransmit.
v3:
- Use unsigned long for min. Bound tcp_timeout_init to TCP_RTO_MAX.
v4: - Refactor duplicate code by adding reqsk_timeout function.
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: ff46e3b44219 ("Fix race for duplicate reqsk on identical SYN")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 151c9c724d05d5b0dd8acd3e11cb69ef1f2dbada ]
We had various syzbot reports about tcp timers firing after
the corresponding netns has been dismantled.
Fortunately Josef Bacik could trigger the issue more often,
and could test a patch I wrote two years ago.
When TCP sockets are closed, we call inet_csk_clear_xmit_timers()
to 'stop' the timers.
inet_csk_clear_xmit_timers() can be called from any context,
including when socket lock is held.
This is the reason it uses sk_stop_timer(), aka del_timer().
This means that ongoing timers might finish much later.
For user sockets, this is fine because each running timer
holds a reference on the socket, and the user socket holds
a reference on the netns.
For kernel sockets, we risk that the netns is freed before
timer can complete, because kernel sockets do not hold
reference on the netns.
This patch adds inet_csk_clear_xmit_timers_sync() function
that using sk_stop_timer_sync() to make sure all timers
are terminated before the kernel socket is released.
Modules using kernel sockets close them in their netns exit()
handler.
Also add sock_not_owned_by_me() helper to get LOCKDEP
support : inet_csk_clear_xmit_timers_sync() must not be called
while socket lock is held.
It is very possible we can revert in the future commit
3a58f13a88 ("net: rds: acquire refcount on TCP sockets")
which attempted to solve the issue in rds only.
(net/smc/af_smc.c and net/mptcp/subflow.c have similar code)
We probably can remove the check_net() tests from
tcp_out_of_resources() and __tcp_close() in the future.
Reported-by: Josef Bacik <josef@toxicpanda.com>
Closes: https://lore.kernel.org/netdev/20240314210740.GA2823176@perftesting/
Fixes: 26abe14379 ("net: Modify sk_alloc to not reference count the netns of kernel sockets.")
Fixes: 8a68173691 ("net: sk_clone_lock() should only do get_net() if the parent is not a kernel socket")
Link: https://lore.kernel.org/bpf/CANn89i+484ffqb93aQm1N-tjxxvb3WDKX0EbD7318RwRgsatjw@mail.gmail.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Josef Bacik <josef@toxicpanda.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Link: https://lore.kernel.org/r/20240322135732.1535772-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cae3873c5b ]
The listen sk is currently stored in two hash tables,
listening_hash (hashed by port) and lhash2 (hashed by port and address).
After commit 0ee58dad5b ("net: tcp6: prefer listeners bound to an address")
and commit d9fbc7f643 ("net: tcp: prefer listeners bound to an address"),
the TCP-SYN lookup fast path does not use listening_hash.
The commit 05c0b35709 ("tcp: seq_file: Replace listening_hash with lhash2")
also moved the seq_file (/proc/net/tcp) iteration usage from
listening_hash to lhash2.
There are still a few listening_hash usages left.
One of them is inet_reuseport_add_sock() which uses the listening_hash
to search a listen sk during the listen() system call. This turns
out to be very slow on use cases that listen on many different
VIPs at a popular port (e.g. 443). [ On top of the slowness in
adding to the tail in the IPv6 case ]. The latter patch has a
selftest to demonstrate this case.
This patch takes this chance to move all remaining listening_hash
usages to lhash2 and then retire listening_hash.
Since most changes need to be done together, it is hard to cut
the listening_hash to lhash2 switch into small patches. The
changes in this patch is highlighted here for the review
purpose.
1. Because of the listening_hash removal, lhash2 can use the
sk->sk_nulls_node instead of the icsk->icsk_listen_portaddr_node.
This will also keep the sk_unhashed() check to work as is
after stop adding sk to listening_hash.
The union is removed from inet_listen_hashbucket because
only nulls_head is needed.
2. icsk->icsk_listen_portaddr_node and its helpers are removed.
3. The current lhash2 users needs to iterate with sk_nulls_node
instead of icsk_listen_portaddr_node.
One case is in the inet[6]_lhash2_lookup().
Another case is the seq_file iterator in tcp_ipv4.c.
One thing to note is sk_nulls_next() is needed
because the old inet_lhash2_for_each_icsk_continue()
does a "next" first before iterating.
4. Move the remaining listening_hash usage to lhash2
inet_reuseport_add_sock() which this series is
trying to improve.
inet_diag.c and mptcp_diag.c are the final two
remaining use cases and is moved to lhash2 now also.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 871019b22d1b ("net: set SOCK_RCU_FREE before inserting socket into hashtable")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4d8f24eeed upstream.
This reverts commit 4a41f453be.
This to-be-reverted commit was meant to apply a stricter rule for the
stack to enter pingpong mode. However, the condition used to check for
interactive session "before(tp->lsndtime, icsk->icsk_ack.lrcvtime)" is
jiffy based and might be too coarse, which delays the stack entering
pingpong mode.
We revert this patch so that we no longer use the above condition to
determine interactive session, and also reduce pingpong threshold to 1.
Fixes: 4a41f453be ("tcp: change pingpong threshold to 3")
Reported-by: LemmyHuang <hlm3280@163.com>
Suggested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220721204404.388396-1-weiwan@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 19757cebf0 ]
Use of percpu_counter structure to track count of orphaned
sockets is causing problems on modern hosts with 256 cpus
or more.
Stefan Bach reported a serious spinlock contention in real workloads,
that I was able to reproduce with a netfilter rule dropping
incoming FIN packets.
53.56% server [kernel.kallsyms] [k] queued_spin_lock_slowpath
|
---queued_spin_lock_slowpath
|
--53.51%--_raw_spin_lock_irqsave
|
--53.51%--__percpu_counter_sum
tcp_check_oom
|
|--39.03%--__tcp_close
| tcp_close
| inet_release
| inet6_release
| sock_close
| __fput
| ____fput
| task_work_run
| exit_to_usermode_loop
| do_syscall_64
| entry_SYSCALL_64_after_hwframe
| __GI___libc_close
|
--14.48%--tcp_out_of_resources
tcp_write_timeout
tcp_retransmit_timer
tcp_write_timer_handler
tcp_write_timer
call_timer_fn
expire_timers
__run_timers
run_timer_softirq
__softirqentry_text_start
As explained in commit cf86a086a1 ("net/dst: use a smaller percpu_counter
batch for dst entries accounting"), default batch size is too big
for the default value of tcp_max_orphans (262144).
But even if we reduce batch sizes, there would still be cases
where the estimated count of orphans is beyond the limit,
and where tcp_too_many_orphans() has to call the expensive
percpu_counter_sum_positive().
One solution is to use plain per-cpu counters, and have
a timer to periodically refresh this cache.
Updating this cache every 100ms seems about right, tcp pressure
state is not radically changing over shorter periods.
percpu_counter was nice 15 years ago while hosts had less
than 16 cpus, not anymore by current standards.
v2: Fix the build issue for CONFIG_CRYPTO_DEV_CHELSIO_TLS=m,
reported by kernel test robot <lkp@intel.com>
Remove unused socket argument from tcp_too_many_orphans()
Fixes: dd24c00191 ("net: Use a percpu_counter for orphan_count")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Stefan Bach <sfb@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Instead of a magic number (13 currently) and having
to change it every other year, use sizeof_field() macro.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tcp_check_req can be called with obsolete req socket for which big
socket have been already created (because of CPU race or early demux
assigning req socket to multiple packets in gro batch).
Commit e0f9759f53 ("tcp: try to keep packet if SYN_RCV race
is lost") added retry in case when tcp_check_req is called for PSH|ACK packet.
But if client sends RST+ACK immediatly after connection being
established (it is performing healthcheck, for example) retry does not
occur. In that case tcp_check_req tries to close req socket,
leaving big socket active.
Fixes: e0f9759f53 ("tcp: try to keep packet if SYN_RCV race is lost")
Signed-off-by: Alexander Ovechkin <ovov@yandex-team.ru>
Reported-by: Oleg Senin <olegsenin@yandex-team.ru>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit shrinks inet_connection_sock by 4 bytes, by shrinking
icsk_mtup.enabled from 32 bits to 1 bit, and shrinking
icsk_mtup.probe_size from s32 to an unsuigned 31 bit field.
This is to save space to compensate for the recent introduction of a
new u32 in inet_connection_sock, icsk_probes_tstamp, in the recent bug
fix commit 9d9b1ee0b2 ("tcp: fix TCP_USER_TIMEOUT with zero window").
This should not change functionality, since icsk_mtup.enabled is only
ever set to 0 or 1, and icsk_mtup.probe_size can only be either 0
or a positive MTU value returned by tcp_mss_to_mtu()
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210129185438.1813237-1-ncardwell.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the early retransmit has been removed by
commit bec41a11dd ("tcp: remove early retransmit"),
we also remove the unused ICSK_TIME_EARLY_RETRANS macro.
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/1611239473-27304-1-git-send-email-yangpc@wangsu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TCP session does not terminate with TCP_USER_TIMEOUT when data
remain untransmitted due to zero window.
The number of unanswered zero-window probes (tcp_probes_out) is
reset to zero with incoming acks irrespective of the window size,
as described in tcp_probe_timer():
RFC 1122 4.2.2.17 requires the sender to stay open indefinitely
as long as the receiver continues to respond probes. We support
this by default and reset icsk_probes_out with incoming ACKs.
This counter, however, is the wrong one to be used in calculating the
duration that the window remains closed and data remain untransmitted.
Thanks to Jonathan Maxwell <jmaxwell37@gmail.com> for diagnosing the
actual issue.
In this patch a new timestamp is introduced for the socket in order to
track the elapsed time for the zero-window probes that have not been
answered with any non-zero window ack.
Fixes: 9721e709fa ("tcp: simplify window probe aborting on USER_TIMEOUT")
Reported-by: William McCall <william.mccall@gmail.com>
Co-developed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Enke Chen <enchen@paloaltonetworks.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210115223058.GA39267@localhost.localdomain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Whenever host is under very high memory pressure,
__tcp_send_ack() skb allocation fails, and we setup
a 200 ms (TCP_DELACK_MAX) timer before retrying.
On hosts with high number of TCP sockets, we can spend
considerable amount of cpu cycles in these attempts,
add high pressure on various spinlocks in mm-layer,
ultimately blocking threads attempting to free space
from making any progress.
This patch adds standard exponential backoff to avoid
adding fuel to the fire.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP has been using it to work around the possibility of tcp_delack_timer()
finding the socket owned by user.
After commit 6f458dfb40 ("tcp: improve latencies of timer triggered events")
we added TCP_DELACK_TIMER_DEFERRED atomic bit for more immediate recovery,
so we can get rid of icsk_ack.blocked
This frees space that following patch will reuse.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change tcp_init_transfer() to only initialize congestion control if it
has not been initialized already.
With this new approach, we can arrange things so that if the EBPF code
sets the congestion control by calling setsockopt(TCP_CONGESTION) then
tcp_init_transfer() will not re-initialize the CC module.
This is an approach that has the following beneficial properties:
(1) This allows CC module customizations made by the EBPF called in
tcp_init_transfer() to persist, and not be wiped out by a later
call to tcp_init_congestion_control() in tcp_init_transfer().
(2) Does not flip the order of EBPF and CC init, to avoid causing bugs
for existing code upstream that depends on the current order.
(3) Does not cause 2 initializations for for CC in the case where the
EBPF called in tcp_init_transfer() wants to set the CC to a new CC
algorithm.
(4) Allows follow-on simplifications to the code in net/core/filter.c
and net/ipv4/tcp_cong.c, which currently both have some complexity
to special-case CC initialization to avoid double CC
initialization if EBPF sets the CC.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Kevin Yang <yyd@google.com>
Cc: Lawrence Brakmo <brakmo@fb.com>
This patch adds bpf_setsockopt(TCP_BPF_RTO_MIN) to allow bpf prog
to set the min rto of a connection. It could be used together
with the earlier patch which has added bpf_setsockopt(TCP_BPF_DELACK_MAX).
A later selftest patch will communicate the max delay ack in a
bpf tcp header option and then the receiving side can use
bpf_setsockopt(TCP_BPF_RTO_MIN) to set a shorter rto.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200820190027.2884170-1-kafai@fb.com
This change is mostly from an internal patch and adapts it from sysctl
config to the bpf_setsockopt setup.
The bpf_prog can set the max delay ack by using
bpf_setsockopt(TCP_BPF_DELACK_MAX). This max delay ack can be communicated
to its peer through bpf header option. The receiving peer can then use
this max delay ack and set a potentially lower rto by using
bpf_setsockopt(TCP_BPF_RTO_MIN) which will be introduced
in the next patch.
Another later selftest patch will also use it like the above to show
how to write and parse bpf tcp header option.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200820190021.2884000-1-kafai@fb.com
Refactor the fastreuse update code in inet_csk_get_port into a small
helper function that can be called from other places.
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Tim Froidcoeur <tim.froidcoeur@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the remaining setsockopt code to pass a sockptr_t instead of a
plain user pointer. This removes the last remaining set_fs(KERNEL_DS)
outside of architecture specific code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> [ieee802154]
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the few cases that need special treatment in-line using
in_compat_syscall(). This also removes all the now unused
compat_{get,set}sockopt methods.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing the 'inet_num' field is necessary and safe if and
only if the socket is not bound. The MPTCP protocol calls
the destroy helper on bound sockets, as tcp_v{4,6}_syn_recv_sock
completed successfully.
Move the clearing of such field out of the common code, otherwise
the MPTCP MP_JOIN error path will find the wrong 'inet_num' value
on socket disposal, __inet_put_port() will acquire the wrong lock
and bind_node removal could race with other modifiers possibly
corrupting the bind hash table.
Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com>
Fixes: 729cd6436f ("mptcp: cope better with MP_JOIN failure")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the steps to prepare an inet_connection_sock for
forced disposal inside a separate helper. No functional
changes inteded, this will just simplify the next patch.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sock map code checks that a socket does not have an active upper
layer protocol before inserting it into the map. This requires casting
via inet_csk, which isn't valid for UDP sockets.
Guard checks for ULP by checking inet_sk(sk)->is_icsk first.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200309111243.6982-2-lmb@cloudflare.com
We need to make sure context does not get freed while diag
code is interrogating it. Free struct tls_context with
kfree_rcu().
We add the __rcu annotation directly in icsk, and cast it
away in the datapath accessor. Presumably all ULPs will
do a similar thing.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to be more confident about an on-going interactive session, we
increment pingpong count by 1 for every interactive transaction and we
adjust TCP_PINGPONG_THRESH to 3.
This means, we only consider a session in pingpong mode after we see 3
interactive transactions, and start to activate delayed acks in quick
ack mode.
And in order to not over-count the credits, we only increase pingpong
count for the first packet sent in response for the previous received
packet.
This is mainly to prevent delaying the ack immediately after some
handshake protocol but no real interactive traffic pattern afterwards.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using pingpong as a single bit information, we refactor the
code to treat it as a counter. When interactive session is detected,
we set pingpong count to TCP_PINGPONG_THRESH. And when pingpong count
is >= TCP_PINGPONG_THRESH, we consider the session in pingpong mode.
This patch is a pure refactor and sets foundation for the next patch.
This patch itself does not change any pingpong logic.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aggregation effects are extremely common with wifi, cellular, and cable
modem link technologies, ACK decimation in middleboxes, and LRO and GRO
in receiving hosts. The aggregation can happen in either direction,
data or ACKs, but in either case the aggregation effect is visible
to the sender in the ACK stream.
Previously BBR's sending was often limited by cwnd under severe ACK
aggregation/decimation because BBR sized the cwnd at 2*BDP. If packets
were acked in bursts after long delays (e.g. one ACK acking 5*BDP after
5*RTT), BBR's sending was halted after sending 2*BDP over 2*RTT, leaving
the bottleneck idle for potentially long periods. Note that loss-based
congestion control does not have this issue because when facing
aggregation it continues increasing cwnd after bursts of ACKs, growing
cwnd until the buffer is full.
To achieve good throughput in the presence of aggregation effects, this
algorithm allows the BBR sender to put extra data in flight to keep the
bottleneck utilized during silences in the ACK stream that it has evidence
to suggest were caused by aggregation.
A summary of the algorithm: when a burst of packets are acked by a
stretched ACK or a burst of ACKs or both, BBR first estimates the expected
amount of data that should have been acked, based on its estimated
bandwidth. Then the surplus ("extra_acked") is recorded in a windowed-max
filter to estimate the recent level of observed ACK aggregation. Then cwnd
is increased by the ACK aggregation estimate. The larger cwnd avoids BBR
being cwnd-limited in the face of ACK silences that recent history suggests
were caused by aggregation. As a sanity check, the ACK aggregation degree
is upper-bounded by the cwnd (at the time of measurement) and a global max
of BW * 100ms. The algorithm is further described by the following
presentation:
https://datatracker.ietf.org/meeting/101/materials/slides-101-iccrg-an-update-on-bbr-work-at-google-00
In our internal testing, we observed a significant increase in BBR
throughput (measured using netperf), in a basic wifi setup.
- Host1 (sender on ethernet) -> AP -> Host2 (receiver on wifi)
- 2.4 GHz -> BBR before: ~73 Mbps; BBR after: ~102 Mbps; CUBIC: ~100 Mbps
- 5.0 GHz -> BBR before: ~362 Mbps; BBR after: ~593 Mbps; CUBIC: ~601 Mbps
Also, this code is running globally on YouTube TCP connections and produced
significant bandwidth increases for YouTube traffic.
This is based on Ian Swett's max_ack_height_ algorithm from the
QUIC BBR implementation.
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the effort to reduce the code duplication between _THIS_IP_
and current_text_addr(), let's consolidate callers of
current_text_addr() to use _THIS_IP_.
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new flag to indicate a one-time immediate ACK. This flag is
occasionaly set under specific TCP protocol states in addition to
the more common quickack mechanism for interactive application.
In several cases in the TCP code we want to force an immediate ACK
but do not want to call tcp_enter_quickack_mode() because we do
not want to forget the icsk_ack.pingpong or icsk_ack.ato state.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
INET_CSK_DEBUG is always set and only is used for 2 pr_debug calls.
EXPORT_SYMBOL(inet_csk_timer_bug_msg) is only used by these 2
pr_debug calls and is also unnecessary as the exported string can
be used directly by these calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Called when a TCP segment is acknowledged.
Could be used by application protocols who hold additional
metadata associated with the stream data.
This is required by TLS device offload to release
metadata associated with acknowledged TLS records.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ran simple script to find/remove trailing whitespace and blank lines
at EOF because that kind of stuff git whines about and editors leave
behind.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
The current listener hashtable is hashed by port only.
When a process is listening at many IP addresses with the same port (e.g.
[IP1]:443, [IP2]:443... [IPN]:443), the inet[6]_lookup_listener()
performance is degraded to a link list. It is prone to syn attack.
UDP had a similar issue and a second hashtable was added to resolve it.
This patch adds a second hashtable for the listener's sockets.
The second hashtable is hashed by port and address.
It cannot reuse the existing skc_portaddr_node which is shared
with skc_bind_node. TCP listener needs to use skc_bind_node.
Instead, this patch adds a hlist_node 'icsk_listen_portaddr_node' to
the inet_connection_sock which the listener (like TCP) also belongs to.
The new portaddr hashtable may need two lookup (First by IP:PORT.
Second by INADDR_ANY:PORT if the IP:PORT is a not found). Hence,
it implements a similar cut off as UDP such that it will only consult the
new portaddr hashtable if the current port-only hashtable has >10
sk in the link-list.
lhash2 and lhash2_mask are added to 'struct inet_hashinfo'. I take
this chance to plug a 4 bytes hole. It is done by first moving
the existing bind_bucket_cachep up and then add the new
(int lhash2_mask, *lhash2) after the existing bhash_size.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Cc: dccp@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the infrustructure for attaching Upper Layer Protocols (ULPs) over TCP
sockets. Based on a similar infrastructure in tcp_cong. The idea is that any
ULP can add its own logic by changing the TCP proto_ops structure to its own
methods.
Example usage:
setsockopt(sock, SOL_TCP, TCP_ULP, "tls", sizeof("tls"));
modules will call:
tcp_register_ulp(&tcp_tls_ulp_ops);
to register/unregister their ulp, with an init function and name.
A list of registered ulps will be returned by tcp_get_available_ulp, which is
hooked up to /proc. Example:
$ cat /proc/sys/net/ipv4/tcp_available_ulp
tls
There is currently no functionality to remove or chain ULPs, but
it should be possible to add these in the future if needed.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lockdep issues a circular dependency warning when AFS issues an operation
through AF_RXRPC from a context in which the VFS/VM holds the mmap_sem.
The theory lockdep comes up with is as follows:
(1) If the pagefault handler decides it needs to read pages from AFS, it
calls AFS with mmap_sem held and AFS begins an AF_RXRPC call, but
creating a call requires the socket lock:
mmap_sem must be taken before sk_lock-AF_RXRPC
(2) afs_open_socket() opens an AF_RXRPC socket and binds it. rxrpc_bind()
binds the underlying UDP socket whilst holding its socket lock.
inet_bind() takes its own socket lock:
sk_lock-AF_RXRPC must be taken before sk_lock-AF_INET
(3) Reading from a TCP socket into a userspace buffer might cause a fault
and thus cause the kernel to take the mmap_sem, but the TCP socket is
locked whilst doing this:
sk_lock-AF_INET must be taken before mmap_sem
However, lockdep's theory is wrong in this instance because it deals only
with lock classes and not individual locks. The AF_INET lock in (2) isn't
really equivalent to the AF_INET lock in (3) as the former deals with a
socket entirely internal to the kernel that never sees userspace. This is
a limitation in the design of lockdep.
Fix the general case by:
(1) Double up all the locking keys used in sockets so that one set are
used if the socket is created by userspace and the other set is used
if the socket is created by the kernel.
(2) Store the kern parameter passed to sk_alloc() in a variable in the
sock struct (sk_kern_sock). This informs sock_lock_init(),
sock_init_data() and sk_clone_lock() as to the lock keys to be used.
Note that the child created by sk_clone_lock() inherits the parent's
kern setting.
(3) Add a 'kern' parameter to ->accept() that is analogous to the one
passed in to ->create() that distinguishes whether kernel_accept() or
sys_accept4() was the caller and can be passed to sk_alloc().
Note that a lot of accept functions merely dequeue an already
allocated socket. I haven't touched these as the new socket already
exists before we get the parameter.
Note also that there are a couple of places where I've made the accepted
socket unconditionally kernel-based:
irda_accept()
rds_rcp_accept_one()
tcp_accept_from_sock()
because they follow a sock_create_kern() and accept off of that.
Whilst creating this, I noticed that lustre and ocfs don't create sockets
through sock_create_kern() and thus they aren't marked as for-kernel,
though they appear to be internal. I wonder if these should do that so
that they use the new set of lock keys.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only difference between inet6_csk_bind_conflict and inet_csk_bind_conflict
is how they check the rcv_saddr, so delete this call back and simply
change inet_csk_bind_conflict to call inet_rcv_saddr_equal.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes RACK install a reordering timer when it suspects
some packets might be lost, but wants to delay the decision
a little bit to accomodate reordering.
It does not create a new timer but instead repurposes the existing
RTO timer, because both are meant to retransmit packets.
Specifically it arms a timer ICSK_TIME_REO_TIMEOUT when
the RACK timing check fails. The wait time is set to
RACK.RTT + RACK.reo_wnd - (NOW - Packet.xmit_time) + fudge
This translates to expecting a packet (Packet) should take
(RACK.RTT + RACK.reo_wnd + fudge) to deliver after it was sent.
When there are multiple packets that need a timer, we use one timer
with the maximum timeout. Therefore the timer conservatively uses
the maximum window to expire N packets by one timeout, instead of
N timeouts to expire N packets sent at different times.
The fudge factor is 2 jiffies to ensure when the timer fires, all
the suspected packets would exceed the deadline and be marked lost
by tcp_rack_detect_loss(). It has to be at least 1 jiffy because the
clock may tick between calling icsk_reset_xmit_timer(timeout) and
actually hang the timer. The next jiffy is to lower-bound the timeout
to 2 jiffies when reo_wnd is < 1ms.
When the reordering timer fires (tcp_rack_reo_timeout): If we aren't
in Recovery we'll enter fast recovery and force fast retransmit.
This is very similar to the early retransmit (RFC5827) except RACK
is not constrained to only enter recovery for small outstanding
flights.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A user may call listen with binding an explicit port with the intent
that the kernel will assign an available port to the socket. In this
case inet_csk_get_port does a port scan. For such sockets, the user may
also set soreuseport with the intent a creating more sockets for the
port that is selected. The problem is that the initial socket being
opened could inadvertently choose an existing and unreleated port
number that was already created with soreuseport.
This patch adds a boolean parameter to inet_bind_conflict that indicates
rather soreuseport is allowed for the check (in addition to
sk->sk_reuseport). In calls to inet_bind_conflict from inet_csk_get_port
the argument is set to true if an explicit port is being looked up (snum
argument is nonzero), and is false if port scan is done.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per listen(fd, backlog) rules, there is really no point accepting a SYN,
sending a SYNACK, and dropping the following ACK packet if accept queue
is full, because application is not draining accept queue fast enough.
This behavior is fooling TCP clients that believe they established a
flow, while there is nothing at server side. They might then send about
10 MSS (if using IW10) that will be dropped anyway while server is under
stress.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilya reported following lockdep splat:
kernel: =========================
kernel: [ BUG: held lock freed! ]
kernel: 4.5.0-rc1-ceph-00026-g5e0a311 #1 Not tainted
kernel: -------------------------
kernel: swapper/5/0 is freeing memory
ffff880035c9d200-ffff880035c9dbff, with a lock still held there!
kernel: (&(&queue->rskq_lock)->rlock){+.-...}, at:
[<ffffffff816f6a88>] inet_csk_reqsk_queue_add+0x28/0xa0
kernel: 4 locks held by swapper/5/0:
kernel: #0: (rcu_read_lock){......}, at: [<ffffffff8169ef6b>]
netif_receive_skb_internal+0x4b/0x1f0
kernel: #1: (rcu_read_lock){......}, at: [<ffffffff816e977f>]
ip_local_deliver_finish+0x3f/0x380
kernel: #2: (slock-AF_INET){+.-...}, at: [<ffffffff81685ffb>]
sk_clone_lock+0x19b/0x440
kernel: #3: (&(&queue->rskq_lock)->rlock){+.-...}, at:
[<ffffffff816f6a88>] inet_csk_reqsk_queue_add+0x28/0xa0
To properly fix this issue, inet_csk_reqsk_queue_add() needs
to return to its callers if the child as been queued
into accept queue.
We also need to make sure listener is still there before
calling sk->sk_data_ready(), by holding a reference on it,
since the reference carried by the child can disappear as
soon as the child is put on accept queue.
Reported-by: Ilya Dryomov <idryomov@gmail.com>
Fixes: ebb516af60 ("tcp/dccp: fix race at listener dismantle phase")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple cpus can process duplicates of incoming ACK messages
matching a SYN_RECV request socket. This is a rare event under
normal operations, but definitely can happen.
Only one must win the race, otherwise corruption would occur.
To fix this without adding new atomic ops, we use logic in
inet_ehash_nolisten() to detect the request was present in the same
ehash bucket where we try to insert the new child.
If request socket was not found, we have to undo the child creation.
This actually removes a spin_lock()/spin_unlock() pair in
reqsk_queue_unlink() for the fast path.
Fixes: e994b2f0fb ("tcp: do not lock listener to process SYN packets")
Fixes: 079096f103 ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under stress, a close() on a listener can trigger the
WARN_ON(sk->sk_ack_backlog) in inet_csk_listen_stop()
We need to test if listener is still active before queueing
a child in inet_csk_reqsk_queue_add()
Create a common inet_child_forget() helper, and use it
from inet_csk_reqsk_queue_add() and inet_csk_listen_stop()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's reduce the confusion about inet_csk_reqsk_queue_drop() :
In many cases we also need to release reference on request socket,
so add a helper to do this, reducing code size and complexity.
Fixes: 4bdc3d6614 ("tcp/dccp: fix behavior of stale SYN_RECV request sockets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At listen() time, there is a small window where listener is visible with
a zero backlog, triggering a spurious "Possible SYN flooding on port"
message.
Nothing prevents us from setting the correct backlog.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This control variable was set at first listen(fd, backlog)
call, but not updated if application tried to increase or decrease
backlog. It made sense at the time listener had a non resizeable
hash table.
Also rounding to powers of two was not very friendly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Akhmat Karakotov
Eric Dumazet
Zhengchao Shao
Martin KaFai Lau
Wei Wang
Alexander Ovechkin
Neal Cardwell
Pengcheng Yang
Enke Chen
Tim Froidcoeur
Christoph Hellwig
Paolo Abeni
Lorenz Bauer
Jakub Kicinski
Thomas Gleixner
Priyaranjan Jha
Nick Desaulniers
Yuchung Cheng
Joe Perches
Ilya Lesokhin
Stephen Hemminger
Linus Torvalds
Al Viro
Kees Cook
Dave Watson
David Howells
Josef Bacik
Tom Herbert