pmbus_do_probe doesn't use the id information provided in its second
argument, so this can be removed, which then allows using the
single-parameter i2c probe function ("probe_new") for probes.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:
* if the information in i2c_client is sufficient, that's used instead
(client->name);
* configured v. probed comparisons are performed by comparing the
configured name to the detected name, instead of the ids; this
involves strcmp but is still cheaper than comparing all the device
names when scanning the tables;
* anything else is handled by calling i2c_match_id() with the same
level of error-handling (if any) as before.
Additionally, the mismatch message in the ltc2978 driver is adjusted
so that it no longer assumes that the driver_data is an index into
ltc2978_id.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200808210004.30880-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding implementation for new attributes (rated_min/rated_max) to
cover PMBus specification about rated values reporting:
MFR_VIN_MIN, MFR_VIN_MAX, MFR_IIN_MAX, MFR_PIN_MAX, MFR_VOUT_MIN,
MFR_VOUT_MAX, MFR_IOUT_MAX, MFR_POUT_MAX, MFR_MAX_TEMP_1/2/3.
Tested with OpenBMC stack. All rated attributes were available
and reported correct values.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-4-git-send-email-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding implementation for new attributes (rated_min/rated_max) for
currentX, inX, powerX, tempX and humidityX.
Tested with OpenBMC stack and simple hwmon driver using
rated_min/rated_max for the following types of sensors: hwmon_temp,
hwmon_in, hwmon_curr, hwmon_power, hwmon_humidity.
For each sensor rated attributes were available and returned
expected values.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-3-git-send-email-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Smatch has a new check for resource leaks which found a bug in probe:
drivers/hwmon/w83627ehf.c:2417 w83627ehf_probe()
warn: 'res->start' not released on lines: 2412.
We need to clean up if devm_hwmon_device_register_with_info() fails.
Fixes: 266cd58359 ("hwmon: (w83627ehf) convert to with_info interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20200921125212.GA1128194@mwanda
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Starting with MAX34451, the chips of this series support STATUS_IOUT and
STATUS_TEMPERATURE commands, and no longer report over-current and
over-temperature status with STATUS_MFR_SPECIFIC.
Fixes: 7a001dbab4 ("hwmon: (pmbus/max34440) Add support for MAX34451.")
Fixes: 50115ac9b6 ("hwmon: (pmbus/max34440) Add support for MAX34460 and MAX34461")
Reported-by: Steve Foreman <foremans@google.com>
Cc: Steve Foreman <foremans@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If the temperature is read before the internal calibration is
completed, the driver returns -EIO. Instead it should return -EAGAIN
to encourage repeating the operation.
Note (groeck): Returning -EAGAIN to userspace may result in hard loops;
some userspace code interprets -EAGAIN as request to retry immediately.
I would prefer -ENODATA, but it turns out that the thermal subsystem only
handles -EAGAIN silently, so we'll have to stick with that.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200903134704.8949-1-lars.povlsen@microchip.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the hardware monitoring controller of the sl28cpld board
management controller. This driver is part of a multi-function device.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
-----BEGIN PGP SIGNATURE-----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=bjMI
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix tempeerature scale in gsc-hwmon driver
- Fix divide by 0 error in nct7904 driver
- Drop non-existing attribute from pmbus/isl68137 driver
- Fix status check in applesmc driver
-----BEGIN PGP SIGNATURE-----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=Nr4L
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix tempeerature scale in gsc-hwmon driver
- Fix divide by 0 error in nct7904 driver
- Drop non-existing attribute from pmbus/isl68137 driver
- Fix status check in applesmc driver
* tag 'hwmon-for-v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (gsc-hwmon) Scale temperature to millidegrees
hwmon: (applesmc) check status earlier.
hwmon: (nct7904) Correct divide by 0
hwmon: (pmbus/isl68137) remove READ_TEMPERATURE_1 telemetry for RAA228228
clang static analysis reports this representative problem
applesmc.c:758:10: warning: 1st function call argument is an
uninitialized value
left = be16_to_cpu(*(__be16 *)(buffer + 6)) >> 2;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
buffer is filled by the earlier call
ret = applesmc_read_key(LIGHT_SENSOR_LEFT_KEY, ...
This problem is reported because a goto skips the status check.
Other similar problems use data from applesmc_read_key before checking
the status. So move the checks to before the use.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Henrik Rydberg <rydberg@bitmath.org>
Link: https://lore.kernel.org/r/20200820131932.10590-1-trix@redhat.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There are multiple drivers using the private adc interface.
It seems unlikely that they would ever get converted to iio,
so make the current state official by making the header file
global.
The s3c2410_ts driver needs a couple of register definitions
as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-22-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Per the RAA228228 datasheet, READ_TEMPERATURE_1 is not a supported PMBus
command.
Signed-off-by: Grant Peltier <grantpeltier93@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The majority of this batch is conversion of the PWM period and duty
cycle to 64-bit unsigned integers, which is required so that some types
of hardware can generate the full range of signals that they're capable
of. The remainder is mostly minor fixes and cleanups.
-----BEGIN PGP SIGNATURE-----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=v6MG
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The majority of this batch is conversion of the PWM period and duty
cycle to 64-bit unsigned integers, which is required so that some
types of hardware can generate the full range of signals that they're
capable of.
The remainder is mostly minor fixes and cleanups"
* tag 'pwm/for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: bcm-iproc: handle clk_get_rate() return
pwm: Replace HTTP links with HTTPS ones
pwm: omap-dmtimer: Repair pwm_omap_dmtimer_chip's broken kerneldoc header
pwm: mediatek: Provide missing kerneldoc description for 'soc' arg
pwm: bcm-kona: Remove impossible comparison when validating duty cycle
pwm: bcm-iproc: Remove impossible comparison when validating duty cycle
pwm: iqs620a: Use lowercase hexadecimal literals for consistency
pwm: Convert period and duty cycle to u64
clk: pwm: Use 64-bit division function
backlight: pwm_bl: Use 64-bit division function
pwm: sun4i: Use nsecs_to_jiffies to avoid a division
pwm: sifive: Use 64-bit division macro
pwm: iqs620a: Use 64-bit division
pwm: imx27: Use 64-bit division macro
pwm: imx-tpm: Use 64-bit division macro
pwm: clps711x: Use 64-bit division macro
hwmon: pwm-fan: Use 64-bit division macro
drm/i915: Use 64-bit division macro
Highlights:
- New driver for Sparx5 SoC temperature sensot
- New driver for Corsair Commander Pro
- MAX20710 support added to max20730 driver
Enhancements:
- max6697: Allow max6581 to create tempX_offset attributes
- gsc (Gateworks System Controller): add 16bit pre-scaled voltage mode
- adm1275: Enable adm1278 ADM1278_TEMP1_EN
- dell-smm: Add Latitude 5480 to fan control whitelist
Fixes:
- adc128d818: Fix advanced configuration register init
- pmbus/core: Use s64 instead of long for calculations
to fix overflow issues with 32-bit architectures
Plus various cleanups in several drivers.
-----BEGIN PGP SIGNATURE-----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=nMNN
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Highlights:
- New driver for Sparx5 SoC temperature sensot
- New driver for Corsair Commander Pro
- MAX20710 support added to max20730 driver
Enhancements:
- max6697: Allow max6581 to create tempX_offset attributes
- gsc (Gateworks System Controller): add 16bit pre-scaled voltage mode
- adm1275: Enable adm1278 ADM1278_TEMP1_EN
- dell-smm: Add Latitude 5480 to fan control whitelist
Fixes:
- adc128d818: Fix advanced configuration register init
- pmbus/core: Use s64 instead of long for calculations to fix
overflow issues with 32-bit architectures
Plus various cleanups in several drivers"
* tag 'hwmon-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (32 commits)
hwmon: (adc128d818) Fix advanced configuration register init
hwmon: (axi-fan-control) remove duplicate macros
hwmon: (i5k_amb, vt8231) Drop uses of pci_read_config_*() return value
hwmon: (sparx5) Make symbol 's5_temp_match' static
hwmon: (corsair-cpro) add reading pwm values
hwmon: sparx5: Add Sparx5 SoC temperature driver
dt-bindings: hwmon: Add Sparx5 temperature sensor
hwmon: (tmp401) Replace HTTP links with HTTPS ones
hwmon: (lm95234) Replace HTTP links with HTTPS ones
hwmon: (lm90) Replace HTTP links with HTTPS ones
hwmon: (k8temp) Replace HTTP links with HTTPS ones
hwmon: (jc42) Replace HTTP links with HTTPS ones
hwmon: (ina2xx) Replace HTTP links with HTTPS ones
hwmon: (ina209) Replace HTTP links with HTTPS ones
hwmon: Replace HTTP links with HTTPS ones
docs: hwmon: Replace HTTP links with HTTPS ones
hwmon: (adm1025) Replace HTTP links with HTTPS ones
hwmon: add Corsair Commander Pro driver
hwmon: (max6697) Allow max6581 to create tempX_offset
hwmon: (tmmp513) Replace HTTP links with HTTPS links
...
If the operation mode is non-zero and an external reference voltage is set,
first the operation mode is written to the advanced configuration register,
followed by the externel reference enable bit,
resetting the configuration mode to 0.
To fix this, first compose the value of the advanced configuration register
based on the configuration mode and the external reference voltage.
The advanced configuration register is then written to the device,
if it is different from the default register value (0x0).
Signed-off-by: Roy van Doormaal <roy.van.doormaal@prodrive-technologies.com>
Link: https://lore.kernel.org/r/20200728151846.231785-1-roy.van.doormaal@prodrive-technologies.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These macros are also present in the "include/linux/fpga/adi-axi-common.h"
file which is included in this driver.
This patch removes them from the AXI Fan Control driver. No sense in having
them in 2 places.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200803054311.98174-1-alexandru.ardelean@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The return value of pci_read_config_*() may not indicate a device error.
However, the value read by these functions is more likely to indicate
this kind of error. This presents two overlapping ways of reporting
errors and complicates error checking.
It is possible to move to one single way of checking for error if the
dependency on the return value of these functions is removed, then it
can later be made to return void.
Remove all uses of the return value of pci_read_config_*().
Check the actual value read for ~0. In this case, ~0 is an invalid
value thus it indicates some kind of error.
Suggested-by: Bjorn Helgaas <bjorn@helgaas.com>
Signed-off-by: Saheed O. Bolarinwa <refactormyself@gmail.com>
Link: https://lore.kernel.org/r/20200801112446.149549-11-refactormyself@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The sparse tool complains as follows:
drivers/hwmon/sparx5-temp.c:150:27: warning:
symbol 's5_temp_match' was not declared. Should it be static?
This variable is not used outside of sparx5-temp.c, this commit
marks it static.
Fixes: c2cb4b5777e1 ("hwmon: sparx5: Add Sparx5 SoC temperature driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200721134919.34033-1-weiyongjun1@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This adds the possibility for reading pwm values.
These can not be read if the device is controlled via
fan_target or a fan curve and will return an error in
this case. Since an error is expected, this adds some
rudimentary error handling.
Changes:
- add CTL_GET_FAN_PWM and use it via get_data
- pwm returns -ENODATA if the device returns error 0x12
- fan_target now returns -ENODATA when the driver is
started or a pwm value is set.
- add ccp_get_errno to determine errno from device error.
- get_data now has a parameter to determine whether
to read one or two bytes of data.
- update documentation
- fix missing surname in MAINTAINERS
Signed-off-by: Marius Zachmann <mail@mariuszachmann.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719181530.60878-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719180521.60811-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719175512.60745-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200713140028.34775-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This is v7 of a driver for the Corsair Commander Pro.
It provides sysfs attributes for:
- Reading fan speed
- Reading temp sensors
- Reading voltage values
- Writing pwm and reading last written pwm
- Reading fan and temp connection status
It is an usb driver, so it needs to be ignored by usbhid.
The Corsair Commander Pro is a fan controller and provides
no means for user interaction.
The two device numbers are there, because there is a slightly
different version of the same device. (Only difference
seem to be in some presets.)
Squashed:
hwmon: (corsair-cpro) add fan_target
This adds fan_target entries to the corsair-cpro driver.
Reading the attribute from the device does not seem possible, so
it returns the last set value (same as pwm).
send_usb_cmd now has one more argument, which is needed for the
fan_target command.
hwmon: corsair-cpro: Change to HID driver
This changes corsair-cpro to a hid driver using hid reports.
Signed-off-by: Marius Zachmann <mail@mariuszachmann.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200626055936.4441-1-mail@mariuszachmann.de
Link: https://lore.kernel.org/r/20200709141413.30790-1-mail@mariuszachmann.de
[groeck: Squashed follow-up patches to avoid changes in HID code]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200703185657.15329-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using s64 type, instead of long type, for internal calculations and for
the sysfs interface.
This allows 64-bit values to appear correctly on 32-bit kernels.
As wattage is reported in microwatts, monitoring a power supply over
2KW requires this.
Although it may seem unlikely to run a 32-bit kernel on such a large
machine, enterprise servers often include a BMC, and the BMC might be
running a 32-bit kernel.
Signed-off-by: Josh Lehan <krellan@google.com>
[groeck: Removed Change-Id and other tags, reformatted description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
add a 16-bit pre-scaled voltage mode to adc and clarify that existing
pre-scaled mode is 24bit.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1591714640-10332-3-git-send-email-tharvey@gateworks.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adm1278 temp attribute need it for openbmc platform .
This feature not enabled by default, so PMON_CONFIG needs to enable it.
Signed-off-by: Manikandan Elumalai <manikandan.hcl.ers.epl@gmail.com>
Link: https://lore.kernel.org/r/20200622153727.GA9347@cnn
[groeck: Split long line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This allows manual PWM control without the BIOS fighting back on Dell
Latitude 5480.
Signed-off-by: Jeffrey Lin <jeffrey@icurse.nl>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200621045246.929649-1-jeffrey@icurse.nl
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The variable res is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200610123638.1133428-1-colin.king@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It has been observed that Toshiba DT01ACA family drives have
WRITE FPDMA QUEUED command timeouts and sometimes just freeze until
power-cycled under heavy write loads when their temperature is getting
polled in SCT mode. The SMART mode seems to be fine, though.
Let's make sure we don't use SCT mode for these drives then.
While only the 3 TB model was actually caught exhibiting the problem let's
play safe here to avoid data corruption and extend the ban to the whole
family.
Fixes: 5b46903d8b ("hwmon: Driver for disk and solid state drives with temperature sensors")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Link: https://lore.kernel.org/r/0cb2e7022b66c6d21d3f189a12a97878d0e7511b.1595075458.git.mail@maciej.szmigiero.name
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SMATCH detected a potential buffer overflow in the manipulation of
hwmon_attributes array inside the scmi_hwmon_probe function:
drivers/hwmon/scmi-hwmon.c:226
scmi_hwmon_probe() error: buffer overflow 'hwmon_attributes' 6 <= 9
Fix it by statically declaring the size of the array as the maximum
possible as defined by hwmon_max define.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20200715121338.GA18761@e119603-lin.cambridge.arm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Stefan Dietrich reports invalid temperature source messages on Asus Formula
XII Z490.
nct6775 nct6775.656: Invalid temperature source 28 at index 0,
source register 0x100, temp register 0x73
Debugging suggests that temperature source 28 reports the CPU temperature.
Let's assume that temperature sources 28 and 29 reflect "PECI Agent {0,1}
Calibration", similar to other chips of the series.
Reported-by: Stefan Dietrich <roots@gmx.de>
Cc: Stefan Dietrich <roots@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Issue:
When PEC is enabled, binding adm1272 to the adm1275 would
fail due to PEC error. See below:
adm1275: probe of xxxx failed with error -74
Diagnosis:
Per the datasheet of adm1272, adm1278, adm1293 and amd1294,
PMON_CONFIG (0xd4) is 16bits wide. On the other hand,
PMON_CONFIG (0xd4) for adm1275 is 8bits wide. The driver should not
assume everything is 8bits wide and read only 8bits from it.
Solution:
If it is adm1272, adm1278, adm1293 and adm1294, use i2c_read_word.
Else, use i2c_read_byte
Testing:
Binding adm1272 to the driver.
The change is only tested on adm1272.
Signed-off-by: Chu Lin <linchuyuan@google.com>
Link: https://lore.kernel.org/r/20200709040612.3977094-1-linchuyuan@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch fixes a bug which does not let FAN mode to be changed from
sysfs(pwm1_enable). i.e pwm1_enable can not be set to 3, it will always
remain at 0.
This is caused because the device driver handles the result of
"read_u8_from_i2c(client, REG_FAN_CONF1, &conf_reg)" incorrectly. The
driver thinks an error has occurred if the (result != 0). This has been
fixed by changing the condition to (result < 0).
Signed-off-by: Vishwas M <vishwas.reddy.vr@gmail.com>
Link: https://lore.kernel.org/r/20200707142747.118414-1-vishwas.reddy.vr@gmail.com
Fixes: 9df7305b5a ("hwmon: Add driver for SMSC EMC2103 temperature monitor and fan controller")
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The energy counters of certain models seems to be reporting
inconsistent values. Hence, match for the supported models.
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Fixes: 8abee9566b ("hwmon: Add amd_energy driver to report energy counters")
Link: https://lore.kernel.org/r/20200706171715.124993-1-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
aspeed_create_fan() reads a pwm_port value using of_property_read_u32().
If pwm_port will be more than ARRAY_SIZE(pwm_port_params), there will be
a buffer overflow in
aspeed_create_pwm_port()->aspeed_set_pwm_port_enable(). The patch fixes
the potential buffer overflow.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Link: https://lore.kernel.org/r/20200703111518.9644-1-novikov@ispras.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix a typo in SENSORS_IR35221 option: module name should be "ir35221"
instead of "ir35521".
Fixes: 8991ebd9c9 ("hwmon: (pmbus) Add client driver for IR35221")
Cc: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20200702221349.18139-1-rentao.bupt@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Although it rarely happens, we should call free_capabilities()
if error happens after read_capabilities() to free allocated strings.
Fixes: de584afa5e ("hwmon driver for ACPI 4.0 power meters")
Signed-off-by: Misono Tomohiro <misono.tomohiro@jp.fujitsu.com>
Link: https://lore.kernel.org/r/20200625043242.31175-1-misono.tomohiro@jp.fujitsu.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per the datasheet for max6697, OVERT mask and ALERT mask are different.
For example, the 7th bit of OVERT is the local channel but for alert
mask, the 6th bit is the local channel. Therefore, we can't apply the
same mask for both registers. In addition to that, the max6697 driver
is supposed to be compatibale with different models. I manually went over
all the listed chips and made sure all chip types have the same layout.
Testing;
mask value of 0x9 should map to 0x44 for ALERT and 0x84 for OVERT.
I used iotool to read the reg value back to verify. I only tested this
change on max6581.
Reference:
https://datasheets.maximintegrated.com/en/ds/MAX6581.pdfhttps://datasheets.maximintegrated.com/en/ds/MAX6697.pdfhttps://datasheets.maximintegrated.com/en/ds/MAX6699.pdf
Signed-off-by: Chu Lin <linchuyuan@google.com>
Fixes: 5372d2d71c ("hwmon: Driver for Maxim MAX6697 and compatibles")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 16358542f3 ("hwmon: (pmbus) Implement multi-phase support")
added support for multi-phase pmbus devices. However, when calling
pmbus_add_sensor() for fans, the patch swapped the `page` and `reg`
attributes. As a result, the fan speeds were reported as 0 RPM on my device.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Fixes: 16358542f3 ("hwmon: (pmbus) Implement multi-phase support")
Cc: stable@vger.kernel.org # v5.7+
Link: https://lore.kernel.org/r/449bc9e6c0e4305581e45905ce9d043b356a9932.1592904387.git.jan.kundrat@cesnet.cz
[groeck: Fixed references to offending commit]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Clang-based kernel building with W=1 warns that some static const
variables are unused:
drivers/hwmon/bt1-pvt.c:67:30: warning: unused variable 'poly_temp_to_N' [-Wunused-const-variable]
static const struct pvt_poly poly_temp_to_N = {
^
drivers/hwmon/bt1-pvt.c:99:30: warning: unused variable 'poly_volt_to_N' [-Wunused-const-variable]
static const struct pvt_poly poly_volt_to_N = {
^
Indeed these polynomials are utilized only when the PVT sensor alarms are
enabled. In that case they are used to convert the temperature and
voltage alarm limits from normal quantities (Volts and degree Celsius) to
the sensor data representation N = [0, 1023]. Otherwise when alarms are
disabled the driver only does the detected data conversion to the human
readable form and doesn't need that polynomials defined. So let's mark the
Temp-to-N and Volt-to-N polynomials with __maybe_unused attribute.
Note gcc with W=1 doesn't notice the problem.
Fixes: 87976ce282 ("hwmon: Add Baikal-T1 PVT sensor driver")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200603000753.391-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since the PWM framework is switching struct pwm_args.period's datatype
to u64, prepare for this transition by using DIV_ROUND_UP_ULL to handle
a 64-bit dividend.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
... into the global msr-index.h header because they're used in multiple
compilation units. Sort the MSR list a bit. Update the msr-index.h copy
in tools.
No functional changes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lkml.kernel.org/r/20200608164847.14232-1-bp@alien8.de
to fixup conflicts in arch/x86/kernel/cpu/mce/core.c so MCE specific follow
up patches can be applied without creating a horrible merge conflict
afterwards.
Baikal-T1 SoC provides an embedded process, voltage and temperature
sensor to monitor an internal SoC environment (chip temperature, supply
voltage and process monitor) and on time detect critical situations,
which may cause the system instability and even damages. The IP-block
is based on the Analog Bits PVT sensor, but is equipped with a
dedicated control wrapper, which provides a MMIO registers-based access
to the sensor core functionality (APB3-bus based) and exposes an
additional functions like thresholds/data ready interrupts, its status
and masks, measurements timeout. All of these is used to create a hwmon
driver being added to the kernel by this commit.
The driver implements support for the hardware monitoring capabilities
of Baikal-T1 process, voltage and temperature sensors. PVT IP-core
consists of one temperature and four voltage sensors, each of which is
implemented as a dedicated hwmon channel config.
The driver can optionally provide the hwmon alarms for each sensor the
PVT controller supports. The alarms functionality is made compile-time
configurable due to the hardware interface implementation peculiarity,
which is connected with an ability to convert data from only one sensor
at a time. Additional limitation is that the controller performs the
thresholds checking synchronously with the data conversion procedure.
Due to these limitations in order to have the hwmon alarms
automatically detected the driver code must switch from one sensor to
another, read converted data and manually check the threshold status
bits. Depending on the measurements timeout settings this design may
cause additional burden on the system performance. By default if the
alarms kernel config is disabled the data conversion is performed by
the driver on demand when read operation is requested via corresponding
_input-file.
Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For hwmon drivers using the hwmon_device_register_with_info() API, it
is desirable to have a generic notification mechanism available. This
mechanism can be used to notify userspace as well as the thermal
subsystem if the driver experiences any events, such as warning or
critical alarms.
Implement hwmon_notify_event() to provide this mechanism. The function
generates a sysfs event and a udev event. If the device is registered
with the thermal subsystem and the event is associated with a temperature
sensor, also notify the thermal subsystem that a thermal event occurred.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Building this driver with "clang -O3" produces a link error
after the compiler partially unrolls the loop and 256ms
becomes a compile-time constant that triggers the check
in udelay():
ld.lld: error: undefined symbol: __bad_udelay
>>> referenced by applesmc.c
>>> hwmon/applesmc.o:(read_smc) in archive drivers/built-in.a
I can see no reason against using a sleeping function here,
as no part of the driver runs in atomic context, so instead use
usleep_range() with a wide range and use jiffies for the
end condition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200527135207.1118624-1-arnd@arndb.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The timeout module parameter should not be used for setting the default
timeout. Because, if you set the timeout = 0, the default timeout will
be meaningless. And the timeout module parameter of 0 means "no timeout
module parameter specified".
Signed-off-by: Yuechao Zhao <yuechao.zhao@advantech.com.cn>
Link: https://lore.kernel.org/r/1590560219-41328-1-git-send-email-yuechao.zhao@advantech.com.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for retrieving Tdie and Tctl on AMD Renoir (4000-series
Ryzen CPUs).
It appears SMU offsets for reading current/voltage and CCD temperature
have changed for this generation (reads from currently used offsets
yield zeros), so those features cannot be enabled so trivially.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lkml.kernel.org/r/20200510204842.2603-3-amonakov@ispras.ru
This patch adds hwmon based amd_energy driver support for
family 17h processors from AMD.
The driver provides following interface to the userspace
1. Reports the per core consumption
* file: "energy%d_input", label: "Ecore%03d"
2. Reports per socket energy consumption
* file: "energy%d_input", label: "Esocket%d"
3. To, increase the wrap around time of the socket energy
counters, a 64bit accumultor is implemented.
4. Reports scaled energy value in Joules.
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20200519155011.56184-1-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the Maxim MAX6654 to the lm90 driver.
The MAX6654 is a temperature sensor, similar to the others,
but with some differences regarding the configuration
register, and the sampling rate at which extended resolution
becomes possible.
Signed-off-by: Josh Lehan <krellan@google.com>
Link: https://lore.kernel.org/r/20200513184248.145765-1-krellan@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use kobj_to_dev() API instead of container_of().
Signed-off-by: zhouchuangao <zhouchuangao@xiaomi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX16601 is a VR13.HC Dual-Output Voltage Regulator Chipset,
implementing a (8+1) multiphase synchronous buck converter.
Cc: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The 'currpage' and 'currphase' variables in struct pmbus_data are used by
the PMBus core to determine if the phase or page value has changed. Both
are initialized with values which are never expected to be set in the code
to ensure that the first page/phase write operation is actually performed.
This is not well explained and occasionally causes confusion. Change the
type of both variables to s16 and initialize with -1 to ensure that the
initial value never matches a requested value, and clarify that this
value means "unknown/unset".
Cc: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
My 'pengutronix' address is defunct for years. Merge the entries and use
the proper contact address.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200502142700.19254-1-wsa@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Check/fix all warnings generated by checkpatch.pl script on LM75 driver.
Signed-off-by: Michal Orzel <michalorzel.eng@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reduce indentation level in __hwmon_device_register() by preparing a
helper function.
This just improves code readability. No functional change.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Implement alert functions for INA226, INA230 and INA231. Expose 06h
Mask/Enable and 07h Alert Limit registers via alert setting and alarm
files.
Signed-off-by: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This commit adds support for lm70 commpatible drivers with systems that
use ACPI.
Signed-off-by: Andrej Picej <andpicej@gmail.com>
[groeck: Fix various issues seen if CONFIG_ACPI=n]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently, each new XPS has to be added manually for module autoloading
to work. Since fan multiplier autodetection should work fine on all XPS
models, just match them all with one block like is done for Precision
and Studio.
The only match we replace that doesn't already use autodetection is
"XPS13" which, according to Google, only matches the XPS 13 9333. (All
other XPS 13 models have "XPS" as its own word, surrounded by spaces.)
According to the thread at [1], autodetection works for the XPS 13 9333,
meaning this shouldn't regress it. I do not own one to confirm with,
though.
Tested on an XPS 13 9350 and confirmed the module now autoloads and
reports reasonable-looking data. I am using BIOS 1.12.2 and do not see
any freezes when querying fan speed.
[1] https://lore.kernel.org/patchwork/patch/525367/
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/5d7e498b83e89ce7c41a449b61919c65d0770b73.1586033337.git.tommyhebb@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Gateworks System Controller has a hwmon sub-component that exposes
up to 16 ADC's, some of which are temperature sensors, others which are
voltage inputs. The ADC configuration (register mapping and name) is
configured via device-tree and varies board to board.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When tsi-as-adc is configured it is possible for in7[0123]_input read to
return an incorrect value if a concurrent read to in[456]_input is
performed. This is caused by a concurrent manipulation of the mux
channel without proper locking as hwmon and mfd use different locks for
synchronization.
Switch hwmon to use the same lock as mfd when accessing the TSI channel.
Fixes: 4f16cab19a ("hwmon: da9052: Add support for TSI channel")
Signed-off-by: Samu Nuutamo <samu.nuutamo@vincit.fi>
[rebase to current master, reword commit message slightly]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The format of temperature limitation registers are 8-bit 2's complement
and the range is -128~127.
Converts the reading value to signed char to fix the incorrect range
of temperature limitation registers.
Signed-off-by: Amy Shih <amy.shih@advantech.com.tw>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When nct7904 power up, it compares current sensor readings against the
default threshold immediately. This results in false alarms on startup.
Read all SMI status registers in probe function to clear the alarms.
Signed-off-by: Amy Shih <amy.shih@advantech.com.tw>
[groeck: Reworded description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If SCT is supported but SCT data tables are not, the driver unnecessarily
tries to fall back to SMART. Use SCT without data tables instead in this
situation.
Fixes: 5b46903d8b ("hwmon: Driver for disk and solid state drives with temperature sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The jc42 driver passes I2C client's name as hwmon device name. In case
of device tree probed devices this ends up being part of the compatible
string, "jc-42.4-temp". This name contains hyphens and the hwmon core
doesn't like this:
jc42 2-0018: hwmon: 'jc-42.4-temp' is not a valid name attribute, please fix
This changes the name to "jc42" which doesn't have any illegal
characters.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20200417092853.31206-1-s.hauer@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix the following sparse warning:
drivers/hwmon/k10temp.c:189:12: warning: symbol 'k10temp_temp_label' was
not declared. Should it be static?
drivers/hwmon/k10temp.c:202:12: warning: symbol 'k10temp_in_label' was
not declared. Should it be static?
drivers/hwmon/k10temp.c:207:12: warning: symbol 'k10temp_curr_label' was
not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200409084502.42126-1-yanaijie@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Holger Hoffstätte observed that Samsung 850 Pro may return invalid
temperatures for a short period of time after resume. Return -ENODATA
to userspace if this is observed.
Fixes: 5b46903d8b ("hwmon: Driver for disk and solid state drives with temperature sensors")
Reported-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Cc: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The addition of the support for reading the temperature of ATA drives as
per commit 5b46903d8b ("hwmon: Driver for disk and solid state drives
with temperature sensors") lists in the respective Kconfig section the
name of the module to be optionally built as "satatemp".
However, building the kernel modules with "CONFIG_SENSORS_DRIVETEMP=m",
does not generate a file named "satatemp.ko".
Instead, the rest of the original commit uses the term "drivetemp" and
a file named "drivetemp.ko" ends up in the kernel's modules directory.
This file has the right ingredients:
$ strings /path/to/drivetemp.ko | grep ^description
description=Hard drive temperature monitor
and modprobing it produces the expected result:
# drivetemp is not loaded
$ sensors -u drivetemp-scsi-4-0
Specified sensor(s) not found!
$ sudo modprobe drivetemp
$ sensors -u drivetemp-scsi-4-0
drivetemp-scsi-4-0
Adapter: SCSI adapter
temp1:
temp1_input: 35.000
temp1_max: 60.000
temp1_min: 0.000
temp1_crit: 70.000
temp1_lcrit: -40.000
temp1_lowest: 20.000
temp1_highest: 36.000
Fix Kconfig by referring to the true name of the module.
Fixes: 5b46903d8b ("hwmon: Driver for disk and solid state drives with temperature sensors")
Signed-off-by: Ann T Ropea <bedhanger@gmx.de>
Link: https://lore.kernel.org/r/20200406235521.185309-1-bedhanger@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
I2C chip IDs need to reflect chip names, not chip functionality.
Fixes: f621d61fd5 ("hwmon: (pmbus) add support for 2nd Gen Renesas digital multiphase")
Cc: Grant Peltier <grantpeltier93@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For security reasons I stopped using gmail account and kernel address is
now up-to-date alias to my personal address.
People periodically send me emails to address which they found in source
code of drivers, so this change reflects state where people can contact
me.
[ Added .mailmap entry as per Joe Perches - Linus ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Joe Perches <joe@perches.com>
Link: http://lkml.kernel.org/r/20200307104237.8199-1-pali@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull perf updates from Ingo Molnar:
"The main changes in this cycle were:
Kernel side changes:
- A couple of x86/cpu cleanups and changes were grandfathered in due
to patch dependencies. These clean up the set of CPU model/family
matching macros with a consistent namespace and C99 initializer
style.
- A bunch of updates to various low level PMU drivers:
* AMD Family 19h L3 uncore PMU
* Intel Tiger Lake uncore support
* misc fixes to LBR TOS sampling
- optprobe fixes
- perf/cgroup: optimize cgroup event sched-in processing
- misc cleanups and fixes
Tooling side changes are to:
- perf {annotate,expr,record,report,stat,test}
- perl scripting
- libapi, libperf and libtraceevent
- vendor events on Intel and S390, ARM cs-etm
- Intel PT updates
- Documentation changes and updates to core facilities
- misc cleanups, fixes and other enhancements"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (89 commits)
cpufreq/intel_pstate: Fix wrong macro conversion
x86/cpu: Cleanup the now unused CPU match macros
hwrng: via_rng: Convert to new X86 CPU match macros
crypto: Convert to new CPU match macros
ASoC: Intel: Convert to new X86 CPU match macros
powercap/intel_rapl: Convert to new X86 CPU match macros
PCI: intel-mid: Convert to new X86 CPU match macros
mmc: sdhci-acpi: Convert to new X86 CPU match macros
intel_idle: Convert to new X86 CPU match macros
extcon: axp288: Convert to new X86 CPU match macros
thermal: Convert to new X86 CPU match macros
hwmon: Convert to new X86 CPU match macros
platform/x86: Convert to new CPU match macros
EDAC: Convert to new X86 CPU match macros
cpufreq: Convert to new X86 CPU match macros
ACPI: Convert to new X86 CPU match macros
x86/platform: Convert to new CPU match macros
x86/kernel: Convert to new CPU match macros
x86/kvm: Convert to new CPU match macros
x86/perf/events: Convert to new CPU match macros
...
The new macro set has a consistent namespace and uses C99 initializers
instead of the grufty C89 ones.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lkml.kernel.org/r/20200320131509.859324598@linutronix.de
There is an additional CCIN for the IBM CFFPS that may be classifed as
either version one or version two, based upon the rest of the bits of
the CCIN. Add support for it in the version detection.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1583948590-17220-1-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a "adi,pwm-active-state" device-tree property to allow hardware
designs to use inverted logic on the PWM output.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[groeck: dev_err -> dev_warn]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Added support for reading DTS properties to set attenuators on
device probe for the ADT7473, ADT7475, ADT7476, and ADT7490.
Signed-off-by: Logan Shaw <logan.shaw@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[groeck: Continuation line formatting; dev_err -> dev_warn]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TPS53647 and TPS53667 are single channel, Step-Down Buck Controllers.
TPS53647 supports 4 phases, TPS53667 supports 6 phases.
The chips do not support per-phase output telemetry.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips of this series with published datasheets support IIN, PIN, and
STATUS_INPUT PMBus commands. Per TI Power Management Forum, "TPS53679 and
TPS53681 have the same PMBus command set". There is no reason to believe
that this does not apply to TPS53688. Let's assume that this is correct
and add support for IIN, PIN, and STATUS_INPUT to TPS53679 and TPS53688
to simplify adding support for more chips of the same series.
At the same time, drop reporting VIN on channel 2. On chips with published
datasheets this voltage is identical to the voltage reported on channel 1,
and there is no reason to believe that this is different for TPS53679 and
TPS53888.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Stephen Kitt
Zbigniew Lukwinski
Dan Carpenter
Guenter Roeck
Lars Povlsen
Michael Walle
Greg Kroah-Hartman
Olof Johansson
Bartosz Golaszewski
Linus Torvalds
Tim Harvey
Gustavo A. R. Silva
Tom Rix
Jason Baron
Arnd Bergmann
Grant Peltier
Roy van Doormaal
Alexandru Ardelean
Saheed O. Bolarinwa
Ingo Molnar
Wei Yongjun
Marius Zachmann
Alexander A. Klimov
Chu Lin
Josh Lehan
Ugur Usug
Manikandan Elumalai
Jeffrey Lin
Wang Qing
Colin Ian King
Maciej S. Szmigiero
Cristian Marussi
Vishwas M
Naveen Krishna Chatradhi
Evgeny Novikov
Tao Ren
Misono Tomohiro
Jan Kundrát
Serge Semin
Guru Das Srinagesh
Borislav Petkov
Thomas Gleixner
Yuechao Zhao
Alexander Monakov
hailizheng
zhouchuangao
Wolfram Sang
Michal Orzel
Akinobu Mita
Alex Qiu
Andrej Picej
Thomas Hebb
Samu Nuutamo
Amy Shih
Sascha Hauer
Jason Yan
Ann T Ropea
Pali Rohár
Eddie James
Takashi Iwai
Chris Packham
Logan Shaw
Henry Shen