Граф коммитов

22 Коммитов

Автор SHA1 Сообщение Дата
Michael Walle 3190ca3b5f net: phy: broadcom: don't export RDB/legacy access methods
Don't export __bcm_phy_enable_rdb_access() and
__bcm_phy_enable_legacy_access() functions. They aren't used outside this
module and it was forgotten to provide a prototype for these functions.
Just make them static for now.

Fixes: 11ecf8c55b ("net: phy: broadcom: add cable test support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-06-01 12:02:57 -07:00
Michael Walle 11ecf8c55b net: phy: broadcom: add cable test support
Most modern broadcom PHYs support ECD (enhanced cable diagnostics). Add
support for it in the bcm-phy-lib so they can easily be used in the PHY
driver.

There are two access methods for ECD: legacy by expansion registers and
via the new RDB registers which are exclusive. Provide functions in two
variants where the PHY driver can choose from. To keep things simple for
now, we just switch the register access to expansion registers in the
RDB variant for now. On the flipside, we have to keep a bus lock to
prevent any other non-legacy access on the PHY.

The results of the intra-pair tests are inconclusive (at least for the
BCM54140). Most of the times half the length is reported but sometimes
the length is correct.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-13 12:52:38 -07:00
Michael Walle e184a9072f net: phy: broadcom: add bcm_phy_modify_exp()
Add the convenience function to do a read-modify-write. This has the
additional benefit of saving one write to the selection register.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-13 12:52:38 -07:00
Michael Walle 7d7e7bce76 net: phy: broadcom: add exp register access methods without buslock
Add helper to read and write expansion registers without taking the mdio
lock.

Please note, that this changes the semantics of the read and write.
Before there was no lock between selecting the expansion register and
the actual read/write. This may lead to access failures if there are
parallel accesses. Instead take the bus lock during the whole access
cycle.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-13 12:52:38 -07:00
Michael Walle 0a32f1ff2a net: phy: broadcom: add helper to write/read RDB registers
RDB (Register Data Base) registers are used on newer Broadcom PHYs. Add
helper to read, write and modify these registers.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-22 12:14:18 -07:00
Murali Krishna Policharla ab41ca3455 net: phy: bcm7xx: add jumbo frame configuration to PHY
The BCM7XX PHY family requires special configuration to pass jumbo
frames. Do that during initial PHY setup.

Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-27 16:07:24 -07:00
Florian Fainelli f878fe5685 net: phy: Prepare for moving Omega out of bcm7xxx
The Omega PHY entry was added to bcm7xxx.c out of convenience and this
breaks the one driver per product line paradigm that was applied up
until now. Since the AFE initialization is shared between Omega and
BCM7xxx move the relevant functions to bcm-phy-lib.[ch]. No functional
changes introduced.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-21 13:41:26 -07:00
Andrew Lunn 84bfe20980 net: phy: Remove redundent License text when SPDX header is present
The SPDX header makes any license text redundent. Remove it.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-22 20:53:08 -08:00
Andrew Lunn a2443fd1a5 net: phy: Convert some PHY and MDIO driver files to SPDX headers
Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-22 20:53:08 -08:00
David S. Miller 5b79c2af66 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Lots of easy overlapping changes in the confict
resolutions here.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-26 19:46:15 -04:00
Florian Fainelli 733a969a7e net: phy: broadcom: Fix auxiliary control register reads
We are currently doing auxiliary control register reads with the shadow
register value 0b111 (0x7) which incidentally is also the selector value
that should be present in bits [2:0]. Fix this by using the appropriate
selector mask which is defined (MII_BCM54XX_AUXCTL_SHDWSEL_MASK).

This does not have a functional impact yet because we always access the
MII_BCM54XX_AUXCTL_SHDWSEL_MISC (0x7) register in the current code.
This might change at some point though.

Fixes: 5b4e290051 ("net: phy: broadcom: add bcm54xx_auxctl_read")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-23 15:18:00 -04:00
Jisheng Zhang 6c3442f5f8 drivers: net: replace UINT64_MAX with U64_MAX
U64_MAX is well defined now while the UINT64_MAX is not, so we fall
back to drivers' own definition as below:

	#ifndef UINT64_MAX
	#define UINT64_MAX             (u64)(~((u64)0))
	#endif

I believe this is in one phy driver then copied and pasted to other phy
drivers.

Replace the UINT64_MAX with U64_MAX to clean up the source code.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27 20:18:55 -04:00
Florian Fainelli 8a17eefa23 net: phy: broadcom: Use strlcpy() for ethtool::get_strings
Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.

Fixes: 820ee17b8d ("net: phy: broadcom: Add support code for reading PHY counters")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-06 11:12:39 -05:00
Russell King a6d99fcd3f net: phy: switch remaining users to phy_(read|write)_mmd()
Switch everyone over to using phy_read_mmd() and phy_write_mmd() now
that they are able to handle both Clause 22 indirect addressing and
Clause 45 direct addressing methods to the MMD registers.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-22 12:43:00 -07:00
Doug Berger cda792c3f9 net: phy: bcm-phylib: replace obsolete EEE macro references
The macros MDIO_AN_EEE_ADV_100TX and MDIO_AN_EEE_ADV_1000T are now
considered obsolete and are replaced in the kernel with the generic
macros MDIO_EEE_100TX and MDIO_EEE_1000T respectively.

Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-13 21:51:48 -07:00
Florian Fainelli 820ee17b8d net: phy: broadcom: Add support code for reading PHY counters
Broadcom PHYs expose a number of PHY error counters: receive errors,
false carrier sense, SerDes BER count, local and remote receive errors.
Add support code to allow retrieving these error counters. Since the
Broadcom PHY library code is used by several drivers, make it possible
for them to specify the storage for the software copy of the statistics.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-30 10:22:27 -05:00
Florian Fainelli 99cec8a4dd net: phy: broadcom: Allow enabling or disabling of EEE
In preparation for adding support for Wirespeed/downshift, we need to
change bcm_phy_eee_enable() to allow enabling or disabling EEE, so make
the function take an extra enable/disable boolean parameter and rename
it to illustrate it sets EEE, not necessarily just enables it.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-24 15:45:53 -05:00
Florian Fainelli d06f78c423 net: phy: broadcom: Add support code for downshift/Wirespeed
Broadcom's Wirespeed feature allows us to configure how auto-negotiation
should behave with fewer working pairs of wires on a cable. Add support
code for retrieving and setting such downshift counters using the
recently added ethtool downshift tunables.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-24 15:45:53 -05:00
Florian Fainelli 5519da874a net: phy: broadcom: Move bcm54xx_auxctl_{read, write} to common library
We are going to need these functions to implement support for Broadcom
Wirespeed, aka downshift.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-24 15:45:53 -05:00
Andrew Lunn 053e7e1692 phy: phy_{read|write}_mmd_indirect: get addr from phydev
The address of the device can be determined from the phydev structure,
rather than passing it as a parameter.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-07 14:31:25 -05:00
Arun Parameswaran b89eb1fcf2 net: phy: bcm-phy-lib: Fix module license issue
The 'bcm-phy-lib.c', added as a part of the commit
"net: phy: Add Broadcom phy library for common interfaces"
was missing the module license. This was causing an issue
when the library is built as a module; "module license
'unspecified' taints kernel".

This patch fixes the issue by adding the module license,
author and description to the bcm-phy-lib.c file.

Fixes: a1cba5613e ("net: phy: Add Broadcom phy library for
common interfaces")
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-18 19:35:10 -07:00
Arun Parameswaran a1cba5613e net: phy: Add Broadcom phy library for common interfaces
This patch adds the Broadcom phy library to consolidate common
interfaces shared by Broadcom phy's.

Moved the common interfaces to the 'bcm-phy-lib.c' and updated
the Broadcom PHY drivers to use the new APIs.

Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-08 04:45:46 -07:00