[ Upstream commit 719c5e37e9 ]
Previously, the defines for phy_device flags in the Micrel driver were
ambiguous in their representation. They were intended to be bit masks
but were mistakenly defined as bit positions. This led to the following
issues:
- MICREL_KSZ8_P1_ERRATA, designated for KSZ88xx switches, overlapped
with MICREL_PHY_FXEN and MICREL_PHY_50MHZ_CLK.
- Due to this overlap, the code path for MICREL_PHY_FXEN, tailored for
the KSZ8041 PHY, was not executed for KSZ88xx PHYs.
- Similarly, the code associated with MICREL_PHY_50MHZ_CLK wasn't
triggered for KSZ88xx.
To rectify this, all three flags have now been explicitly converted to
use the `BIT()` macro, ensuring they are defined as bit masks and
preventing potential overlaps in the future.
Fixes: 49011e0c15 ("net: phy: micrel: ksz886x/ksz8081: add cabletest support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch support for cable test for the ksz886x switches and the
ksz8081 PHY.
The patch was tested on a KSZ8873RLL switch with following results:
- port 1:
- provides invalid values, thus return -ENOTSUPP
(Errata: DS80000830A: "LinkMD does not work on Port 1",
http://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8873-Errata-DS80000830A.pdf)
- port 2:
- can detect distance
- can detect open on each wire of pair A (wire 1 and 2)
- can detect open only on one wire of pair B (only wire 3)
- can detect short between wires of a pair (wires 1 + 2 or 3 + 6)
- short between pairs is detected as open.
For example short between wires 2 + 3 is detected as open.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for MDI-X status and configuration
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some micrel devices share the same PHY register defines. This patch
moves them to one common header so other drivers can reuse them.
And reuse generic MII_* defines where possible.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN8814 is a low-power, quad-port triple-speed (10BASE-T/100BASETX/1000BASE-T)
Ethernet physical layer transceiver (PHY). It supports transmission and
reception of data on standard CAT-5, as well as CAT-5e and CAT-6, unshielded
twisted pair (UTP) cables.
LAN8814 supports industry-standard QSGMII (Quad Serial Gigabit Media
Independent Interface) and Q-USGMII (Quad Universal Serial Gigabit Media
Independent Interface) providing chip-to-chip connection to four Gigabit
Ethernet MACs using a single serialized link (differential pair) in each
direction.
The LAN8814 SKU supports high-accuracy timestamping functions to
support IEEE-1588 solutions using Microchip Ethernet switches, as well as
customer solutions based on SoCs and FPGAs.
The LAN8804 SKU has same features as that of LAN8814 SKU except that it does
not support 1588, SyncE, or Q-USGMII with PCH/MCH.
This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T,
QSGMII link with the MAC.
Signed-off-by: Divya Koppera<divya.koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ8795 PHY ID is in fact used by KSZ8794/KSZ8795/KSZ8765 switches.
Update the PHY ID and name to reflect that, as this family of switches
is commonly refered to as KSZ87xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Microchip Technology KSZ9131 10/100/1000 Ethernet PHY
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding Microchip 9477 Phy included in KSZ9477 Switch.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is adds support for the PHYs in the KSZ8795 5port managed switch.
It will allow to detect the link between the switch and the soc
and uses the same read_status functions as the KSZ8873MLL switch.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't detect the FXEN (fiber mode) bootstrap pin, so configure
it via a boolean device tree property "micrel,fiber-mode".
If it is enabled, auto-negotiation is not supported.
The only available modes are 100base-fx (full duplex and half duplex).
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic RMII-Reference-Clock-Select support.
Several Micrel PHY have an RMII-Reference-Clock-Select bit to select
25 MHz or 50 MHz clock mode. Recently, support for configuring this
through device tree for KSZ8021 and KSZ8031 was added.
Generalise this support so that it can be configured for other PHY types
as well.
Note that some PHY revisions (of the same type) has this bit inverted.
This should be either configurable through a new device-tree property,
or preferably, determined based on PHY ID if possible.
Also note that this removes support for setting 25 MHz mode from board
files which was also added by the above mentioned commit 45f56cb82e45
("net/phy: micrel: Add clock support for KSZ8021/KSZ8031").
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ8021 and KSZ8031 support RMII reference input clocks of 25MHz
and 50MHz. Both PHYs differ in the default frequency they expect
after reset. If this differs from the actual input clock, then
register 0x1f bit 7 must be changed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas R-Car development boards use KSZ8041RNLI PHY which for some reason has
ID of 0x00221537 that is not documented for KSZ8041-family PHYs and does not
match the documented ID of 0x0022151x (where 'x' is the revision). We have
to add the new #define PHY_ID_* and new ksphy_driver[] entry, almost the same
as KSZ8041 one, differing only in the 'phy_id' and 'name' fields.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add defines for common Micrel PHY setups so that other platforms
can use them. Update imx61 and sama5 hardware to use the micrel_phy.h
PHY defines.
Also add support for the KSZ9021RLRN PHY.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: David S. Miller <davem@davemloft.net>
CC: Andrew Victor <linux@maxim.org.za>
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Micrel PHY KSZ8031 is similar to KSZ8021 and also requires the special
initialization of "Operation Mode Strap Override" in reg 0x16
introduced in 212ea99 (phy/micrel: Implement support for KSZ8021).
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Summary of changes:
.Newly added phys
-KSZ8081/KSZ8091, which has some phy ids.
-KSZ8061
-KSZ9031, which is Gigabit phy.
-KSZ886X, which has a switch function.
-KSZ8031, which has a same phy ids with KSZ8021.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this will allow to detect the link between the switch and the soc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The license header was missing in micrel_phy.h . This patch adds
one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no such part as KS8001, KS8041 or KS8051. There are only
KSZ8001, KSZ8041 and KSZ8051. Rename these parts as such to match
the Micrel naming.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Linux ARM kernel <linux-arm-kernel@lists.infradead.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ8021 PHY was previously caught by KS8051, which is not correct.
This PHY needs additional setup if it is strapped for address 0. In such
case an reserved bit must be written in the 0x16, "Operation Mode Strap
Override" register. According to the KS8051 datasheet, that bit means
"PHY Address 0 in non-broadcast" and it indeed behaves as such on KSZ8021.
The issue where the ethernet controller (Freescale FEC) did not communicate
with network is fixed by writing this bit as 1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right ID of KSZ9021 is 0x00221610.
Because lower 4bit is a revision number, it varies according to a chip.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Platform code can now set the MICREL_PHY_50MHZ_CLK bit of dev_flags in a fixup
routine (registered with phy_register_fixup_for_uid()), to make the KZS8051RNL
PHY work with 50MHz RMII reference clock.
Cc: David J. Choi <david.choi@micrel.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksij Rempel
Michael Grzeschik
Divya Koppera
Marek Vasut
Thomas Gleixner
Yuiko Oshino
Woojung Huh
Sean Nyekjaer
Philipp Zabel
Johan Hovold
Sascha Hauer
Sergei Shtylyov
Dinh Nguyen
Hector Palacios
David J. Choi
Jean-Christophe PLAGNIOL-VILLARD
Nobuhiro Iwamatsu
Baruch Siach