Граф коммитов

44 Коммитов

Автор SHA1 Сообщение Дата
Tom Rix 9d253c02ac ethtool: remove unneeded semicolon
A semicolon is not needed after a switch statement.

Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20201101155601.2294374-1-trix@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-11-02 17:50:53 -08:00
Igor Russkikh c6db31ffe2 ethtool: allow netdev driver to define phy tunables
Define get/set phy tunable callbacks in ethtool ops.
This will allow MAC drivers with integrated PHY still to implement
these tunables.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-10-06 06:16:01 -07:00
Edward Cree 2adc6edcae ethtool: fix error handling in ethtool_phys_id
If ops->set_phys_id() returned an error, previously we would only break
 out of the inner loop, which neither stopped the outer loop nor returned
 the error to the user (since 'rc' would be overwritten on the next pass
 through the loop).
Thus, rewrite it to use a single loop, so that the break does the right
 thing.  Use u64 for 'count' and 'i' to prevent overflow in case of
 (unreasonably) large values of id.data and n.

Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-03 14:59:51 -07:00
David S. Miller 150f29f5e6 Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:

====================
pull-request: bpf-next 2020-09-01

The following pull-request contains BPF updates for your *net-next* tree.

There are two small conflicts when pulling, resolve as follows:

1) Merge conflict in tools/lib/bpf/libbpf.c between 88a8212028 ("libbpf: Factor
   out common ELF operations and improve logging") in bpf-next and 1e891e513e
   ("libbpf: Fix map index used in error message") in net-next. Resolve by taking
   the hunk in bpf-next:

        [...]
        scn = elf_sec_by_idx(obj, obj->efile.btf_maps_shndx);
        data = elf_sec_data(obj, scn);
        if (!scn || !data) {
                pr_warn("elf: failed to get %s map definitions for %s\n",
                        MAPS_ELF_SEC, obj->path);
                return -EINVAL;
        }
        [...]

2) Merge conflict in drivers/net/ethernet/mellanox/mlx5/core/en/xsk/rx.c between
   9647c57b11 ("xsk: i40e: ice: ixgbe: mlx5: Test for dma_need_sync earlier for
   better performance") in bpf-next and e20f0dbf20 ("net/mlx5e: RX, Add a prefetch
   command for small L1_CACHE_BYTES") in net-next. Resolve the two locations by retaining
   net_prefetch() and taking xsk_buff_dma_sync_for_cpu() from bpf-next. Should look like:

        [...]
        xdp_set_data_meta_invalid(xdp);
        xsk_buff_dma_sync_for_cpu(xdp, rq->xsk_pool);
        net_prefetch(xdp->data);
        [...]

We've added 133 non-merge commits during the last 14 day(s) which contain
a total of 246 files changed, 13832 insertions(+), 3105 deletions(-).

The main changes are:

1) Initial support for sleepable BPF programs along with bpf_copy_from_user() helper
   for tracing to reliably access user memory, from Alexei Starovoitov.

2) Add BPF infra for writing and parsing TCP header options, from Martin KaFai Lau.

3) bpf_d_path() helper for returning full path for given 'struct path', from Jiri Olsa.

4) AF_XDP support for shared umems between devices and queues, from Magnus Karlsson.

5) Initial prep work for full BPF-to-BPF call support in libbpf, from Andrii Nakryiko.

6) Generalize bpf_sk_storage map & add local storage for inodes, from KP Singh.

7) Implement sockmap/hash updates from BPF context, from Lorenz Bauer.

8) BPF xor verification for scalar types & add BPF link iterator, from Yonghong Song.

9) Use target's prog type for BPF_PROG_TYPE_EXT prog verification, from Udip Pant.

10) Rework BPF tracing samples to use libbpf loader, from Daniel T. Lee.

11) Fix xdpsock sample to really cycle through all buffers, from Weqaar Janjua.

12) Improve type safety for tun/veth XDP frame handling, from Maciej Żenczykowski.

13) Various smaller cleanups and improvements all over the place.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-01 13:22:59 -07:00
Magnus Karlsson c4655761d3 xsk: i40e: ice: ixgbe: mlx5: Rename xsk zero-copy driver interfaces
Rename the AF_XDP zero-copy driver interface functions to better
reflect what they do after the replacement of umems with buffer
pools in the previous commit. Mostly it is about replacing the
umem name from the function names with xsk_buff and also have
them take the a buffer pool pointer instead of a umem. The
various ring functions have also been renamed in the process so
that they have the same naming convention as the internal
functions in xsk_queue.h. This so that it will be clearer what
they do and also for consistency.

Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-3-git-send-email-magnus.karlsson@intel.com
2020-08-31 21:15:04 +02:00
Magnus Karlsson 1742b3d528 xsk: i40e: ice: ixgbe: mlx5: Pass buffer pool to driver instead of umem
Replace the explicit umem reference passed to the driver in AF_XDP
zero-copy mode with the buffer pool instead. This in preparation for
extending the functionality of the zero-copy mode so that umems can be
shared between queues on the same netdev and also between netdevs. In
this commit, only an umem reference has been added to the buffer pool
struct. But later commits will add other entities to it. These are
going to be entities that are different between different queue ids
and netdevs even though the umem is shared between them.

Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-2-git-send-email-magnus.karlsson@intel.com
2020-08-31 21:15:03 +02:00
Vishal Kulkarni d0a84e1f38 ethtool: allow flow-type ether without IP protocol field
Set IP protocol mask only when IP protocol field is set.
This will allow flow-type ether with vlan rule which don't have
protocol field to apply.

ethtool -N ens5f4 flow-type ether proto 0x8100 vlan 0x600\
m 0x1FFF action 3 loc 16

Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-20 16:26:03 -07:00
Florian Fainelli 17809516a0 net: phy: Uninline PHY ethtool statistics operations
Now that we have moved the PHY ethtool statistics to be dynamically
registered, we no longer need to inline those for ethtool. This used to
be done to avoid cross symbol referencing and allow ethtool to be
decoupled from PHYLIB entirely.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-08 12:39:05 -07:00
David S. Miller 7bed145516 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.

Signed-off-by: David S. Miller <davem@davemloft.net>
2020-06-25 19:29:51 -07:00
Gaurav Singh 21a739c64d ethtool: Fix check in ethtool_rx_flow_rule_create
Fix check in ethtool_rx_flow_rule_create

Fixes: eca4205f9e ("ethtool: add ethtool_rx_flow_spec to flow_rule structure translator")
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-06-22 20:48:12 -07:00
Gustavo A. R. Silva 3dd1499666 ethtool: ioctl: Use array_size() in copy_to_user()
Use array_size() helper instead of the open-coded version in
copy_to_user(). These sorts of multiplication factors need to
be wrapped in array_size().

This issue was found with the help of Coccinelle and, audited and fixed
manually.

Addresses-KSPP-ID: https://github.com/KSPP/linux/issues/83
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-06-17 15:04:57 -07:00
Heiner Kallweit 316107119f ethtool: propagate get_coalesce return value
get_coalesce returns 0 or ERRNO, but the return value isn't checked.
The returned coalesce data may be invalid if an ERRNO is set,
therefore better check and propagate the return value.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-23 16:57:00 -07:00
David S. Miller a152b85984 Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:

====================
pull-request: bpf-next 2020-05-23

The following pull-request contains BPF updates for your *net-next* tree.

We've added 50 non-merge commits during the last 8 day(s) which contain
a total of 109 files changed, 2776 insertions(+), 2887 deletions(-).

The main changes are:

1) Add a new AF_XDP buffer allocation API to the core in order to help
   lowering the bar for drivers adopting AF_XDP support. i40e, ice, ixgbe
   as well as mlx5 have been moved over to the new API and also gained a
   small improvement in performance, from Björn Töpel and Magnus Karlsson.

2) Add getpeername()/getsockname() attach types for BPF sock_addr programs
   in order to allow for e.g. reverse translation of load-balancer backend
   to service address/port tuple from a connected peer, from Daniel Borkmann.

3) Improve the BPF verifier is_branch_taken() logic to evaluate pointers
   being non-NULL, e.g. if after an initial test another non-NULL test on
   that pointer follows in a given path, then it can be pruned right away,
   from John Fastabend.

4) Larger rework of BPF sockmap selftests to make output easier to understand
   and to reduce overall runtime as well as adding new BPF kTLS selftests
   that run in combination with sockmap, also from John Fastabend.

5) Batch of misc updates to BPF selftests including fixing up test_align
   to match verifier output again and moving it under test_progs, allowing
   bpf_iter selftest to compile on machines with older vmlinux.h, and
   updating config options for lirc and v6 segment routing helpers, from
   Stanislav Fomichev, Andrii Nakryiko and Alan Maguire.

6) Conversion of BPF tracing samples outdated internal BPF loader to use
   libbpf API instead, from Daniel T. Lee.

7) Follow-up to BPF kernel test infrastructure in order to fix a flake in
   the XDP selftests, from Jesper Dangaard Brouer.

8) Minor improvements to libbpf's internal hashmap implementation, from
   Ian Rogers.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-22 18:30:34 -07:00
Magnus Karlsson a71506a4fd xsk: Move driver interface to xdp_sock_drv.h
Move the AF_XDP zero-copy driver interface to its own include file
called xdp_sock_drv.h. This, hopefully, will make it more clear for
NIC driver implementors to know what functions to use for zero-copy
support.

v4->v5: Fix -Wmissing-prototypes by include header file. (Jakub)

Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-4-bjorn.topel@gmail.com
2020-05-21 17:31:26 -07:00
Jakub Kicinski 75c36dbb1c ethtool: don't call set_channels in drivers if config didn't change
Don't call drivers if nothing changed. Netlink code already
contains this logic.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-16 13:56:30 -07:00
Jakub Kicinski 7be92514b9 ethtool: check if there is at least one channel for TX/RX in the core
Having a channel config with no ability to RX or TX traffic is
clearly wrong. Check for this in the core so the drivers don't
have to.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-16 13:56:30 -07:00
Oleksij Rempel bdbdac7649 ethtool: provide UAPI for PHY master/slave configuration.
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of
auto-negotiation support, we needed to be able to configure the
MASTER-SLAVE role of the port manually or from an application in user
space.

The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to
force MASTER or SLAVE role. See IEEE 802.3-2018:
22.2.4.3.7 MASTER-SLAVE control register (Register 9)
22.2.4.3.8 MASTER-SLAVE status register (Register 10)
40.5.2 MASTER-SLAVE configuration resolution
45.2.1.185.1 MASTER-SLAVE config value (1.2100.14)
45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32)

The MASTER-SLAVE role affects the clock configuration:

-------------------------------------------------------------------------------
When the  PHY is configured as MASTER, the PMA Transmit function shall
source TX_TCLK from a local clock source. When configured as SLAVE, the
PMA Transmit function shall source TX_TCLK from the clock recovered from
data stream provided by MASTER.

iMX6Q                     KSZ9031                XXX
------\                /-----------\        /------------\
      |                |           |        |            |
 MAC  |<----RGMII----->| PHY Slave |<------>| PHY Master |
      |<--- 125 MHz ---+-<------/  |        | \          |
------/                \-----------/        \------------/
                                               ^
                                                \-TX_TCLK

-------------------------------------------------------------------------------

Since some clock or link related issues are only reproducible in a
specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial
to provide generic (not 100BASE-T1 specific) interface to the user space
for configuration flexibility and trouble shooting.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-06 17:45:45 -07:00
Leon Romanovsky 1c79031f8a drivers: Remove inclusion of vermagic header
Get rid of linux/vermagic.h includes, so that MODULE_ARCH_VERMAGIC from
the arch header arch/x86/include/asm/module.h won't be redefined.

  In file included from ./include/linux/module.h:30,
                   from drivers/net/ethernet/3com/3c515.c:56:
  ./arch/x86/include/asm/module.h:73: warning: "MODULE_ARCH_VERMAGIC"
redefined
     73 | # define MODULE_ARCH_VERMAGIC MODULE_PROC_FAMILY
        |
  In file included from drivers/net/ethernet/3com/3c515.c:25:
  ./include/linux/vermagic.h:28: note: this is the location of the
previous definition
     28 | #define MODULE_ARCH_VERMAGIC ""
        |

Fixes: 6bba2e89a8 ("net/3com: Delete driver and module versions from 3com drivers")
Co-developed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Shannon Nelson <snelson@pensando.io> # ionic
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-21 13:27:37 -07:00
Andrew Lunn 77e9b2ab45 net: ethtool: self_test: Mark interface in testing operative status
When an interface is executing a self test, put the interface into
operative status testing.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-20 12:43:24 -07:00
Michal Kubecek 5b071c59ed ethtool: provide timestamping information with TSINFO_GET request
Implement TSINFO_GET request to get timestamping information for a network
device. This is traditionally available via ETHTOOL_GET_TS_INFO ioctl
request.

Move part of ethtool_get_ts_info() into common.c so that ioctl and netlink
code use the same logic to get timestamping information from the device.

v3: use "TSINFO" rather than "TIMESTAMP", suggested by Richard Cochran

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-29 22:32:37 -07:00
Michal Kubecek 6c5bc8fe4e ethtool: add EEE_NTF notification
Send ETHTOOL_MSG_EEE_NTF notification whenever EEE settings of a network
device are modified using ETHTOOL_MSG_EEE_SET netlink message or
ETHTOOL_SEEE ioctl request.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-29 22:32:36 -07:00
Michal Kubecek bf37faa386 ethtool: add PAUSE_NTF notification
Send ETHTOOL_MSG_PAUSE_NTF notification whenever pause parameters of
a network device are modified using ETHTOOL_MSG_PAUSE_SET netlink message
or ETHTOOL_SPAUSEPARAM ioctl request.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-29 22:32:36 -07:00
Michal Kubecek 0cf3eac8c9 ethtool: add COALESCE_NTF notification
Send ETHTOOL_MSG_COALESCE_NTF notification whenever coalescing parameters
of a network device are modified using ETHTOOL_MSG_COALESCE_SET netlink
message or ETHTOOL_SCOALESCE ioctl request.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-29 22:32:36 -07:00
Vladyslav Tarasiuk 9d648fb560 ethtool: fix incorrect tx-checksumming settings reporting
Currently, ethtool feature mask for checksum command is ORed with
NETIF_F_FCOE_CRC_BIT, which is bit's position number, instead of the
actual feature bit - NETIF_F_FCOE_CRC.

The invalid bitmask here might affect unrelated features when toggling
TX checksumming. For example, TX checksumming is always mistakenly
reported as enabled on the netdevs tested (mlx5, virtio_net).

Fixes: f70bb06563 ("ethtool: update mapping of features to legacy ioctl requests")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-24 16:25:11 -07:00
Jakub Kicinski 9000edb71a net: ethtool: require drivers to set supported_coalesce_params
Now that all in-tree drivers have been updated we can
make the supported_coalesce_params mandatory.

To save debugging time in case some driver was missed
(or is out of tree) add a warning when netdev is registered
with set_coalesce but without supported_coalesce_params.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-17 20:56:58 -07:00
Michal Kubecek 546379b9a0 ethtool: add CHANNELS_NTF notification
Send ETHTOOL_MSG_CHANNELS_NTF notification whenever channel counts of
a network device are modified using ETHTOOL_MSG_CHANNELS_SET netlink
message or ETHTOOL_SCHANNELS ioctl request.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-12 15:32:33 -07:00
Michal Kubecek e19c591eaf ethtool: set device channel counts with CHANNELS_SET request
Implement CHANNELS_SET netlink request to set channel counts of a network
device. These are traditionally set with ETHTOOL_SCHANNELS ioctl request.

Like the ioctl implementation, the generic ethtool code checks if supplied
values do not exceed driver defined limits; if they do, first offending
attribute is reported using extack. Checks preventing removing channels
used for RX indirection table or zerocopy AF_XDP socket are also
implemented.

Move ethtool_get_max_rxfh_channel() helper into common.c so that it can be
used by both ioctl and netlink code.

v2:
  - fix netdev reference leak in error path (found by Jakub Kicinsky)

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-12 15:32:33 -07:00
Michal Kubecek bc9d1c995e ethtool: add RINGS_NTF notification
Send ETHTOOL_MSG_RINGS_NTF notification whenever ring sizes of a network
device are modified using ETHTOOL_MSG_RINGS_SET netlink message or
ETHTOOL_SRINGPARAM ioctl request.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-12 15:32:33 -07:00
Michal Kubecek 111dcba3c6 ethtool: add PRIVFLAGS_NTF notification
Send ETHTOOL_MSG_PRIVFLAGS_NTF notification whenever private flags of
a network device are modified using ETHTOOL_MSG_PRIVFLAGS_SET netlink
message or ETHTOOL_SPFLAGS ioctl request.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-12 15:32:33 -07:00
Michal Kubecek 0524399d46 ethtool: provide netdev features with FEATURES_GET request
Implement FEATURES_GET request to get network device features. These are
traditionally available via ETHTOOL_GFEATURES ioctl request.

v2:
  - style cleanup suggested by Jakub Kicinski

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-12 15:32:32 -07:00
Michal Kubecek f70bb06563 ethtool: update mapping of features to legacy ioctl requests
Legacy ioctl request like ETHTOOL_GTXCSUM are still used by ethtool utility
to get values of legacy flags (which rather work as feature groups). These
are calculated from values of actual features and request to set them is
implemented as an attempt to set all features mapping to them but there are
two inconsistencies:

- tx-checksum-fcoe-crc is shown under tx-checksumming but NETIF_F_FCOE_CRC
  is not included in ETHTOOL_GTXCSUM/ETHTOOL_STXCSUM
- tx-scatter-gather-fraglist is shown under scatter-gather but
  NETIF_F_FRAGLIST is not included in ETHTOOL_GSG/ETHTOOL_SSG

As the mapping in ethtool output is more correct from logical point of
view, fix ethtool_get_feature_mask() to match it.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-12 15:32:32 -07:00
Jakub Kicinski 95cddcb5cc ethtool: add infrastructure for centralized checking of coalescing parameters
Linux supports 22 different interrupt coalescing parameters.
No driver implements them all. Some drivers just ignore the
ones they don't support, while others have to carry a long
list of checks to reject unsupported settings.

To simplify the drivers add the ability to specify inside
ethtool_ops which parameters are supported and let the core
reject attempts to set any other one.

This commit makes the mechanism an opt-in, only drivers which
set ethtool_opts->coalesce_types to a non-zero value will have
the checks enforced.

The same mask is used for global and per queue settings.

v3: - move the (temporary) check if driver defines types
      earlier (Michal)
    - rename used_types -> nonzero_params, and
      coalesce_types -> supported_coalesce_params (Alex)
    - use EOPNOTSUPP instead of EINVAL (Andrew, Michal)

Leaving the long series of ifs for now, it seems nice to
be able to grep for the field and flag names. This will
probably have to be revisited once netlink support lands.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-05 12:12:34 -08:00
Cris Forno 70ae1e127b ethtool: Factored out similar ethtool link settings for virtual devices to core
Three virtual devices (ibmveth, virtio_net, and netvsc) all have
similar code to set link settings and validate ethtool command. To
eliminate duplication of code, it is factored out into core/ethtool.c.

Signed-off-by: Cris Forno <cforno12@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-29 21:48:54 -08:00
Leon Romanovsky 6a7e25c7fb net/core: Replace driver version to be kernel version
In order to stop useless driver version bumps and unify output
presented by ethtool -i, let's set default version string.

As Linus said in [1]: "Things are supposed to be backwards and
forwards compatible, because we don't accept breakage in user
space anyway. So versioning is pointless, and only causes
problems."

They cause problems when users start to see version changes
and expect specific set of features which will be different
for stable@, vanilla and distribution kernels.

Distribution kernels are based on some kernel version with extra
patches on top, for example, in RedHat world this "extra" is a lot
and for them your driver version say nothing. Users who run vanilla
kernels won't use driver version information too, because running
such kernels requires knowledge and understanding.

Another set of problems are related to difference in versioning scheme
and such doesn't allow to write meaningful automation which will work
sanely on all ethtool capable devices.

Before this change:
[leonro@erver ~]$ ethtool -i eth0
driver: virtio_net
version: 1.0.0
After this change and once ->version assignment will be deleted
from virtio_net:
[leonro@server ~]$ ethtool -i eth0
driver: virtio_net
version: 5.5.0-rc6+

Link: https://lore.kernel.org/ksummit-discuss/CA+55aFx9A=5cc0QZ7CySC4F2K7eYaEfzkdYEc9JaNgCcV25=rg@mail.gmail.com/
Link: https://lore.kernel.org/linux-rdma/20200122152627.14903-1-michal.kalderon@marvell.com/T/#md460ff8f976c532a89d6860411c3c50bb811038b
Link: https://lore.kernel.org/linux-rdma/20200127060835.GA570@unicorn.suse.cz
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-27 13:47:22 +01:00
Michal Kubecek 67bffa7923 ethtool: add WOL_NTF notification
Send ETHTOOL_MSG_WOL_NTF notification whenever wake-on-lan settings of
a device are modified using ETHTOOL_MSG_WOL_SET netlink message or
ETHTOOL_SWOL ioctl request.

As notifications can be received by anyone, do not include SecureOn(tm)
password in notification messages.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-27 11:31:36 +01:00
Michal Kubecek 0bda7af39d ethtool: add DEBUG_NTF notification
Send ETHTOOL_MSG_DEBUG_NTF notification message whenever debugging message
mask for a device are modified using ETHTOOL_MSG_DEBUG_SET netlink message
or ETHTOOL_SMSGLVL ioctl request.

The notification message has the same format as reply to DEBUG_GET request.
As with other ethtool notifications, netlink requests only trigger the
notification if the mask is actually changed while ioctl request trigger it
whenever the request results in calling the ethtool_ops handler.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-27 11:31:36 +01:00
Michal Kubecek 3d2b847fb9 ethtool: provide link state with LINKSTATE_GET request
Implement LINKSTATE_GET netlink request to get link state information.

At the moment, only link up flag as provided by ETHTOOL_GLINK ioctl command
is returned.

LINKSTATE_GET request can be used with NLM_F_DUMP (without device
identification) to request the information for all devices in current
network namespace providing the data.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-27 16:40:02 -08:00
Michal Kubecek 1b1b1847c8 ethtool: add LINKMODES_NTF notification
Send ETHTOOL_MSG_LINKMODES_NTF notification message whenever device link
settings or advertised modes are modified using ETHTOOL_MSG_LINKMODES_SET
netlink message or ETHTOOL_SLINKSETTINGS or ETHTOOL_SSET ioctl commands.

The notification message has the same format as reply to LINKMODES_GET
request. ETHTOOL_MSG_LINKMODES_SET netlink request only triggers the
notification if there is a change but the ioctl command handlers do not
check if there is an actual change and trigger the notification whenever
the commands are executed.

As all work is done by ethnl_default_notify() handler and callback
functions introduced to handle LINKMODES_GET requests, all that remains is
adding entries for ETHTOOL_MSG_LINKMODES_NTF into ethnl_notify_handlers and
ethnl_default_notify_ops lookup tables and calls to ethtool_notify() where
needed.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-27 16:40:02 -08:00
Michal Kubecek 73286734c1 ethtool: add LINKINFO_NTF notification
Send ETHTOOL_MSG_LINKINFO_NTF notification message whenever device link
settings are modified using ETHTOOL_MSG_LINKINFO_SET netlink message or
ETHTOOL_SLINKSETTINGS or ETHTOOL_SSET ioctl commands.

The notification message has the same format as reply to LINKINFO_GET
request. ETHTOOL_MSG_LINKINFO_SET netlink request only triggers the
notification if there is a change but the ioctl command handlers do not
check if there is an actual change and trigger the notification whenever
the commands are executed.

As all work is done by ethnl_default_notify() handler and callback
functions introduced to handle LINKINFO_GET requests, all that remains is
adding entries for ETHTOOL_MSG_LINKINFO_NTF into ethnl_notify_handlers and
ethnl_default_notify_ops lookup tables and calls to ethtool_notify() where
needed.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-27 16:40:02 -08:00
Michal Kubecek 459e0b81b3 ethtool: provide link settings with LINKINFO_GET request
Implement LINKINFO_GET netlink request to get basic link settings provided
by ETHTOOL_GLINKSETTINGS and ETHTOOL_GSET ioctl commands.

This request provides settings not directly related to autonegotiation and
link mode selection: physical port, phy MDIO address, MDI(-X) status,
MDI(-X) control and transceiver.

LINKINFO_GET request can be used with NLM_F_DUMP (without device
identification) to request the information for all devices in current
network namespace providing the data.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-27 16:40:02 -08:00
Richard Cochran 7774ee2368 net: ethtool: Use the PHY time stamping interface.
The ethtool layer tests fields of the phy_device in order to determine
whether to invoke the PHY's tsinfo ethtool callback.  This patch
replaces the open coded logic with an invocation of the proper
methods.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-25 19:51:33 -08:00
Michal Kubecek 428c122f5f ethtool: provide link mode names as a string set
Unlike e.g. netdev features, the ethtool ioctl interface requires link mode
table to be in sync between kernel and userspace for userspace to be able
to display and set all link modes supported by kernel. The way arbitrary
length bitsets are implemented in netlink interface, this will be no longer
needed.

To allow userspace to access all link modes running kernel supports, add
table of ethernet link mode names and make it available as a string set to
userspace GET_STRSET requests. Add build time check to make sure names
are defined for all modes declared in enum ethtool_link_mode_bit_indices.

Once the string set is available, make it also accessible via ioctl.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-12 17:07:05 -08:00
Michal Kubecek d44e13108b ethtool: move string arrays into common file
Introduce file net/ethtool/common.c for code shared by ioctl and netlink
ethtool interface. Move name tables of features, RSS hash functions,
tunables and PHY tunables into this file.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-12 17:07:05 -08:00
Michal Kubecek 9ce48e5a09 ethtool: move to its own directory
The ethtool netlink interface is going to be split into multiple files so
that it will be more convenient to put all of them in a separate directory
net/ethtool. Start by moving current ethtool.c with ioctl interface into
this directory and renaming it to ioctl.c.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-12 17:07:05 -08:00