In commit 10724cc7bb ("tipc: redesign connection-level flow control")
we replaced the previous message based flow control with one based on
1k blocks. In order to ensure backwards compatibility the mechanism
falls back to using message as base unit when it senses that the peer
doesn't support the new algorithm. The default flow control window,
i.e., how many units can be sent before the sender blocks and waits
for an acknowledge (aka advertisement) is 512. This was tested against
the previous version, which uses an acknowledge frequency of on ack per
256 received message, and found to work fine.
However, we missed the fact that versions older than Linux 3.15 use an
acknowledge frequency of 512, which is exactly the limit where a 4.6+
sender will stop and wait for acknowledge. This would also work fine if
it weren't for the fact that if the first sent message on a 4.6+ server
side is an empty SYNACK, this one is also is counted as a sent message,
while it is not counted as a received message on a legacy 3.15-receiver.
This leads to the sender always being one step ahead of the receiver, a
scenario causing the sender to block after 512 sent messages, while the
receiver only has registered 511 read messages. Hence, the legacy
receiver is not trigged to send an acknowledge, with a permanently
blocked sender as result.
We solve this deadlock by simply allowing the sender to send one more
message before it blocks, i.e., by a making minimal change to the
condition used for determining connection congestion.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ETHTOOL_GLINKSETTINGS command is deprecating the ETHTOOL_GSET
command and likewise it shouldn't require the CAP_NET_ADMIN capability.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 35c55c9877 ("tipc: add neighbor monitoring framework") we
added a data area to the link monitor STATE messages under the
assumption that previous versions did not use any such data area.
For versions older than Linux 4.3 this assumption is not correct. In
those version, all STATE messages sent out from a node inadvertently
contain a 16 byte data area containing a string; -a leftover from
previous RESET messages which were using this during the setup phase.
This string serves no purpose in STATE messages, and should no be there.
Unfortunately, this data area is delivered to the link monitor
framework, where a sanity check catches that it is not a correct domain
record, and drops it. It also issues a rate limited warning about the
event.
Since such events occur much more frequently than anticipated, we now
choose to remove the warning in order to not fill the kernel log with
useless contents. We also make the sanity check stricter, to further
reduce the risk that such data is inavertently admitted.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 817298102b ("tipc: fix link priority propagation") introduced a
compatibility problem between TIPC versions newer than Linux 4.6 and
those older than Linux 4.4. In versions later than 4.4, link STATE
messages only contain a non-zero link priority value when the sender
wants the receiver to change its priority. This has the effect that the
receiver resets itself in order to apply the new priority. This works
well, and is consistent with the said commit.
However, in versions older than 4.4 a valid link priority is present in
all sent link STATE messages, leading to cyclic link establishment and
reset on the 4.6+ node.
We fix this by adding a test that the received value should not only
be valid, but also differ from the current value in order to cause the
receiving link endpoint to reset.
Reported-by: Amar Nv <amar.nv005@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEES2FAuYbJvAGobdVQPTuqJaypJWoFAlg1ppETHG1rbEBwZW5n
dXRyb25peC5kZQAKCRA9O6olrKklaqieB/4o9PaD8Rj38Piy7lJW1ahAxoUnY4AA
Vu1eFvtidUswO5RV6mDOuqhTulzrMcPQZguW/S7eLZh6hWYVVLlgkrNLj/RpMXsH
rqGRC/sL5ICL1q/ijYK6NJJ3+GFQhl92gG+wJxsQfETWVDKH13N3sWcEyBh0+C5P
lnPFNVDVSy4bpkEgXAN/sfAvoHzW//34cnxTzlsd1COAWlxZ+HHgBAGp4kaYTpbF
Vz3kuNPfDI7U+36quE8SUXe/R9HfqQBtfbFtaxha8vqH8Fw6MJYO0BUJVmtawTDq
nBFvB/x+d0n1YeOgo5UD5bW9thItF57GEscWqYpTuhZ0jlPr5+CZeo14
=FImK
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.9-20161123' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-11-23
this is a pull request for net/master.
The patch by Oliver Hartkopp for the broadcast manager (bcm) fixes the
CAN-FD support, which may cause an out-of-bounds access otherwise.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth 2016-11-23
Sorry about the late pull request for 4.9, but we have one more
important Bluetooth patch that should make it to the release. It fixes
connection creation for Bluetooth LE controllers that do not have a
public address (only a random one).
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Should pass valid filter handle, not the netlink flags.
Fixes: 30a391a13a ("net sched filters: pass netlink message flags in event notification")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commits 93821778de ("udp: Fix rcv socket locking") and
f7ad74fef3 ("net/ipv6/udp: UDP encapsulation: break backlog_rcv into
__udpv6_queue_rcv_skb") UDP backlog handlers were renamed, but UDPlite
was forgotten.
This leads to crashes if UDPlite header is pulled twice, which happens
starting from commit e6afc8ace6 ("udp: remove headers from UDP packets
before queueing")
Bug found by syzkaller team, thanks a lot guys !
Note that backlog use in UDP/UDPlite is scheduled to be removed starting
from linux-4.10, so this patch is only needed up to linux-4.9
Fixes: 93821778de ("udp: Fix rcv socket locking")
Fixes: f7ad74fef3 ("net/ipv6/udp: UDP encapsulation: break backlog_rcv into __udpv6_queue_rcv_skb")
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an ipv6 address has the tentative flag set, it can't be
used as source for egress traffic, while the associated route,
if any, can be looked up and even stored into some dst_cache.
In the latter scenario, the source ipv6 address selected and
stored in the cache is most probably wrong (e.g. with
link-local scope) and the entity using the dst_cache will
experience lack of ipv6 connectivity until said cache is
cleared or invalidated.
Overall this may cause lack of connectivity over most IPv6 tunnels
(comprising geneve and vxlan), if the first egress packet reaches
the tunnel before the DaD is completed for the used ipv6
address.
This patch bumps a new genid after that the IFA_F_TENTATIVE flag
is cleared, so that dst_cache will be invalidated on
next lookup and ipv6 connectivity restored.
Fixes: 0c1d70af92 ("net: use dst_cache for vxlan device")
Fixes: 468dfffcd7 ("geneve: add dst caching support")
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 7c6ae610a1, because l2tp_xmit_skb() never
returns NET_XMIT_CN, it ignores the return value of l2tp_xmit_core().
Cc: Gao Feng <gfree.wind@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RT netlink, calcit() function should return the minimal size for
netlink dump message. This will make sure that dump message for every
network device can be stored.
Currently, rtnl_calcit() function doesn't account the size of header of
netlink message, this patch will fix it.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 6f3b911d5f ("can: bcm: add support for CAN FD frames") the
CAN broadcast manager supports CAN and CAN FD data frames.
As these data frames are embedded in struct can[fd]_frames which have a
different length the access to the provided array of CAN frames became
dependend of op->cfsiz. By using a struct canfd_frame pointer for the array of
CAN frames the new offset calculation based on op->cfsiz was accidently applied
to CAN FD frame element lengths.
This fix makes the pointer to the arrays of the different CAN frame types a
void pointer so that the offset calculation in bytes accesses the correct CAN
frame elements.
Reference: http://marc.info/?l=linux-netdev&m=147980658909653
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The hci_get_route() API is used to look up local HCI devices, however
so far it has been incapable of dealing with anything else than the
public address of HCI devices. This completely breaks with LE-only HCI
devices that do not come with a public address, but use a static
random address instead.
This patch exteds the hci_get_route() API with a src_type parameter
that's used for comparing with the right address of each HCI device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Andre Noll reported panics after my recent fix (commit 34fad54c25
"net: __skb_flow_dissect() must cap its return value")
After some more headaches, Alexander root caused the problem to
init_default_flow_dissectors() being called too late, in case
a network driver like IGB is not a module and receives DHCP message
very early.
Fix is to call init_default_flow_dissectors() much earlier,
as it is a core infrastructure and does not depend on another
kernel service.
Fixes: 06635a35d1 ("flow_dissect: use programable dissector in skb_flow_dissect and friends")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andre Noll <maan@tuebingen.mpg.de>
Diagnosed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Clear congestion control state when changing algorithms on an
existing socket, from Florian Westphal.
2) Fix register bit values in altr_tse_pcs portion of stmmac driver,
from Jia Jie Ho.
3) Fix PTP handling in stammc driver for GMAC4, from Giuseppe
CAVALLARO.
4) Fix udplite multicast delivery handling, it ignores the udp_table
parameter passed into the lookups, from Pablo Neira Ayuso.
5) Synchronize the space estimated by rtnl_vfinfo_size and the space
actually used by rtnl_fill_vfinfo. From Sabrina Dubroca.
6) Fix memory leak in fib_info when splitting nodes, from Alexander
Duyck.
7) If a driver does a napi_hash_del() explicitily and not via
netif_napi_del(), it must perform RCU synchronization as needed. Fix
this in virtio-net and bnxt drivers, from Eric Dumazet.
8) Likewise, it is not necessary to invoke napi_hash_del() is we are
also doing neif_napi_del() in the same code path. Remove such calls
from be2net and cxgb4 drivers, also from Eric Dumazet.
9) Don't allocate an ID in peernet2id_alloc() if the netns is dead,
from WANG Cong.
10) Fix OF node and device struct leaks in of_mdio, from Johan Hovold.
11) We cannot cache routes in ip6_tunnel when using inherited traffic
classes, from Paolo Abeni.
12) Fix several crashes and leaks in cpsw driver, from Johan Hovold.
13) Splice operations cannot use freezable blocking calls in AF_UNIX,
from WANG Cong.
14) Link dump filtering by master device and kind support added an error
in loop index updates during the dump if we actually do filter, fix
from Zhang Shengju.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
tcp: zero ca_priv area when switching cc algorithms
net: l2tp: Treat NET_XMIT_CN as success in l2tp_eth_dev_xmit
ethernet: stmmac: make DWMAC_STM32 depend on it's associated SoC
tipc: eliminate obsolete socket locking policy description
rtnl: fix the loop index update error in rtnl_dump_ifinfo()
l2tp: fix racy SOCK_ZAPPED flag check in l2tp_ip{,6}_bind()
net: macb: add check for dma mapping error in start_xmit()
rtnetlink: fix FDB size computation
netns: fix get_net_ns_by_fd(int pid) typo
af_unix: conditionally use freezable blocking calls in read
net: ethernet: ti: cpsw: fix fixed-link phy probe deferral
net: ethernet: ti: cpsw: add missing sanity check
net: ethernet: ti: cpsw: fix secondary-emac probe error path
net: ethernet: ti: cpsw: fix of_node and phydev leaks
net: ethernet: ti: cpsw: fix deferred probe
net: ethernet: ti: cpsw: fix mdio device reference leak
net: ethernet: ti: cpsw: fix bad register access in probe error path
net: sky2: Fix shutdown crash
cfg80211: limit scan results cache size
net sched filters: pass netlink message flags in event notification
...
We need to zero out the private data area when application switches
connection to different algorithm (TCP_CONGESTION setsockopt).
When congestion ops get assigned at connect time everything is already
zeroed because sk_alloc uses GFP_ZERO flag. But in the setsockopt case
this contains whatever previous cc placed there.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tc could return NET_XMIT_CN as one congestion notification, but
it does not mean the packe is lost. Other modules like ipvlan,
macvlan, and others treat NET_XMIT_CN as success too.
So l2tp_eth_dev_xmit should add the NET_XMIT_CN check.
Signed-off-by: Gao Feng <gfree.wind@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment block in socket.c describing the locking policy is
obsolete, and does not reflect current reality. We remove it in this
commit.
Since the current locking policy is much simpler and follows a
mainstream approach, we see no need to add a new description.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the link is filtered out, loop index should also be updated. If not,
loop index will not be correct.
Fixes: dc599f76c2 ("net: Add support for filtering link dump by master device and kind")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Revert a splat on disabling interface which created another problem,
by Sven Eckelmann
- Fix error handling when the primary interface disappears during a
throughput meter test, by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=DdJj
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20161119' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are two batman-adv bugfix patches:
- Revert a splat on disabling interface which created another problem,
by Sven Eckelmann
- Fix error handling when the primary interface disappears during a
throughput meter test, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=F2DQ
-----END PGP SIGNATURE-----
Merge tag 'nfsd-4.9-2' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfix from Bruce Fields:
"Just one fix for an NFS/RDMA crash"
* tag 'nfsd-4.9-2' of git://linux-nfs.org/~bfields/linux:
sunrpc: svc_age_temp_xprts_now should not call setsockopt non-tcp transports
Add missing NDA_VLAN attribute's size.
Fixes: 1e53d5bb88 ("net: Pass VLAN ID to rtnl_fdb_notify.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* limit # of scan results stored in memory - this is a long-standing bug
Jouni and I only noticed while discussing other things in Santa Fe
* revert AP_LINK_PS patch that was causing issues (Felix)
* various A-MSDU/A-MPDU fixes for TXQ code (Felix)
* interoperability workaround for peers with broken VHT capabilities
(Filip Matusiak)
* add bitrate definition for a VHT MCS that's supposed to be invalid
but gets used by some hardware anyway (Thomas Pedersen)
* beacon timer fix in hwsim (Benjamin Beichler)
-----BEGIN PGP SIGNATURE-----
iQIcBAABCgAGBQJYLrKJAAoJEGt7eEactAAdshYP/Rwi/k9WZ0RKQIA1QA0fnmwv
TbUUvPHQ4LA39Czs0JwOPDIbter7TBzFXV5EK0y39jGm8St4a/oHuN072kzBYvob
YbBzM0YKV2uQCAjH3AjWjS3RPOlTzfUqSRWgEqtgUTC5VZrpNfhd2r0q+jfwpQ7s
+qUsdwqvVJMZKfOEngIXzNXdI95N1d8tpGwzkUqDbOJ+7amdriiJKyTsKEOMqREA
0Mdhu6roEcMDVO+xt5ZkilmpLZOUEHAzaWkwm7d6VToWi7k3pwMiEZ4fthvHZHEZ
6K2bn1UMLdKAExRcQBE3wrmn5jFfUbts1mhmoN1drHocI12epcgw5I4ZjEbfpqMB
IBkOM+2hbSdUVfE4KVH6iubqiJwtHB8YSTdKFmMO4jPx7UshPF7YCny6XWC+EqQm
ktjyG/lhlXJ0HaOKC/MAwd/KSzfH0eJWGNBDV5s/FIWiqu2oWn+ZIX7vGTpp4K1Z
Rery/ZUiJGzVITNG1ka+GXq2tUvDXfkMApr+jFH4G6zioWovxB6+4uyMEeclvC5q
zjgYEpZhbn2wQUNEJ8btDDgXkyDGh3UPjy93fO8fMEvv8d9CCOKTQkIUpjPp6jbZ
EoLCTW0NNjnAmQRiUFF3vO2O7e3ZTJ4hyNEVkc7mJ2X3DllXRSelTIFSfZVHpb2k
P+gY7uC0cAPZ4s6q8GSb
=q2mI
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few more bugfixes:
* limit # of scan results stored in memory - this is a long-standing bug
Jouni and I only noticed while discussing other things in Santa Fe
* revert AP_LINK_PS patch that was causing issues (Felix)
* various A-MSDU/A-MPDU fixes for TXQ code (Felix)
* interoperability workaround for peers with broken VHT capabilities
(Filip Matusiak)
* add bitrate definition for a VHT MCS that's supposed to be invalid
but gets used by some hardware anyway (Thomas Pedersen)
* beacon timer fix in hwsim (Benjamin Beichler)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2b15af6f95 ("af_unix: use freezable blocking calls in read")
converts schedule_timeout() to its freezable version, it was probably
correct at that time, but later, commit 2b514574f7
("net: af_unix: implement splice for stream af_unix sockets") breaks
the strong requirement for a freezable sleep, according to
commit 0f9548ca1091:
We shouldn't try_to_freeze if locks are held. Holding a lock can cause a
deadlock if the lock is later acquired in the suspend or hibernate path
(e.g. by dpm). Holding a lock can also cause a deadlock in the case of
cgroup_freezer if a lock is held inside a frozen cgroup that is later
acquired by a process outside that group.
The pipe_lock is still held at that point.
So use freezable version only for the recvmsg call path, avoid impact for
Android.
Fixes: 2b514574f7 ("net: af_unix: implement splice for stream af_unix sockets")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Colin Cross <ccross@android.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible to make scanning consume almost arbitrary amounts
of memory, e.g. by sending beacon frames with random BSSIDs at
high rates while somebody is scanning.
Limit the number of BSS table entries we're willing to cache to
1000, limiting maximum memory usage to maybe 4-5MB, but lower
in practice - that would be the case for having both full-sized
beacon and probe response frames for each entry; this seems not
possible in practice, so a limit of 1000 entries will likely be
closer to 0.5 MB.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Userland client should be able to read an event, and reflect it back to
the kernel, therefore it needs to extract complete set of netlink flags.
For example, this will allow "tc monitor" to distinguish Add and Replace
operations.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an ip6 tunnel is configured to inherit the traffic class from
the inner header, the dst_cache must be disabled or it will foul
the policy routing.
The issue is apprently there since at leat Linux-2.6.12-rc2.
Reported-by: Liam McBirnie <liam.mcbirnie@boeing.com>
Cc: Liam McBirnie <liam.mcbirnie@boeing.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrei reports we still allocate netns ID from idr after we destroy
it in cleanup_net().
cleanup_net():
...
idr_destroy(&net->netns_ids);
...
list_for_each_entry_reverse(ops, &pernet_list, list)
ops_exit_list(ops, &net_exit_list);
-> rollback_registered_many()
-> rtmsg_ifinfo_build_skb()
-> rtnl_fill_ifinfo()
-> peernet2id_alloc()
After that point we should not even access net->netns_ids, we
should check the death of the current netns as early as we can in
peernet2id_alloc().
For net-next we can consider to avoid sending rtmsg totally,
it is a good optimization for netns teardown path.
Fixes: 0c7aecd4bd ("netns: add rtnl cmd to add and get peer netns ids")
Reported-by: Andrei Vagin <avagin@gmail.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IOP_XATTR flag is set on sockfs because sockfs supports getting the
"system.sockprotoname" xattr. Since commit 6c6ef9f2, this flag is checked for
setxattr support as well. This is wrong on sockfs because security xattr
support there is supposed to be provided by security_inode_setsecurity. The
smack security module relies on socket labels (xattrs).
Fix this by adding a security xattr handler on sockfs that returns
-EAGAIN, and by checking for -EAGAIN in setxattr.
We cannot simply check for -EOPNOTSUPP in setxattr because there are
filesystems that neither have direct security xattr support nor support
via security_inode_setsecurity. A more proper fix might be to move the
call to security_inode_setsecurity into sockfs, but it's not clear to me
if that is safe: we would end up calling security_inode_post_setxattr after
that as well.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix a small memory leak that can occur where we leak a fib_alias in the
event of us not being able to insert it into the local table.
Fixes: 0ddcf43d5d ("ipv4: FIB Local/MAIN table collapse")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch that removed the FIB offload infrastructure was a bit too
aggressive and also removed code needed to clean up us splitting the table
if additional rules were added. Specifically the function
fib_trie_flush_external was called at the end of a new rule being added to
flush the foreign trie entries from the main trie.
I updated the code so that we only call fib_trie_flush_external on the main
table so that we flush the entries for local from main. This way we don't
call it for every rule change which is what was happening previously.
Fixes: 347e3b28c1 ("switchdev: remove FIB offload infrastructure")
Reported-by: Eric Dumazet <edumazet@google.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_xdp_size() only considers the size of the actual payload attribute,
and misses the space taken by the attribute used for nesting (IFLA_XDP).
Fixes: d1fdd91386 ("rtnl: add option for setting link xdp prog")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size reported by rtnl_vfinfo_size doesn't match the space used by
rtnl_fill_vfinfo.
rtnl_vfinfo_size currently doesn't account for the nest attributes
used by statistics (added in commit 3b766cd832), nor for struct
ifla_vf_tx_rate (since commit ed616689a3, which added ifla_vf_rate
to the dump without removing ifla_vf_tx_rate, but replaced
ifla_vf_tx_rate with ifla_vf_rate in the size computation).
Fixes: 3b766cd832 ("net/core: Add reading VF statistics through the PF netdevice")
Fixes: ed616689a3 ("net-next:v4: Add support to configure SR-IOV VF minimum and maximum Tx rate through ip tool")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Honor udptable parameter that is passed to __udp*_lib_mcast_deliver(),
otherwise udplite broadcast/multicast use the wrong table and it breaks.
Fixes: 2dc41cff75 ("udp: Use hash2 for long hash1 chains in __udp*_lib_mcast_deliver.")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 24cf3af3fe ("igmp: call ip_mc_clear_src..."), we forgot to remove
igmpv3_clear_delrec() in ip_mc_down(), which also called ip_mc_clear_src().
This make us clear all IGMPv3 source filter info after NETDEV_DOWN.
Move igmpv3_clear_delrec() to ip_mc_destroy_dev() and then no need
ip_mc_clear_src() in ip_mc_destroy_dev().
On the other hand, we should restore back instead of free all source filter
info in igmpv3_del_delrec(). Or we will not able to restore IGMPv3 source
filter info after NETDEV_UP and NETDEV_POST_TYPE_CHANGE.
Fixes: 24cf3af3fe ("igmp: call ip_mc_clear_src() only when ...")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A-MSDU aggregation alters the QoS header after a frame has been
enqueued, so it needs to be ready before enqueue and not overwritten
again afterwards
Fixes: bb42f2d13f ("mac80211: Move reorder-sensitive TX handlers to after TXQ dequeue")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The call to ieee80211_txq_enqueue overwrites the vif pointer with the
codel enqueue time, so setting it just before that call makes no sense.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The sequence number counter is used to derive the starting sequence
number. Since that counter is updated on tx dequeue, the A-MPDU flag
needs to be up to date at the tme of dequeue as well.
This patch prevents sending more A-MPDU frames after the session has
been terminated and also ensures that aggregation starts right after the
session has been established
Fixes: bb42f2d13f ("mac80211: Move reorder-sensitive TX handlers to after TXQ dequeue")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers (ath10k) report MCS 9 @ 20MHz, which
technically isn't defined. To get more meaningful value
than 0 out of this however, just extrapolate a bitrate
from ratio of MCS 7 and 9 in channels where it is allowed.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
[add a comment about it in the code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit c68df2e7be.
__sta_info_recalc_tim turns into a no-op if local->ops->set_tim is not
set. This prevents the beacon TIM bit from being set for all drivers
that do not implement this op (almost all of them), thus thoroughly
essential AP mode powersave functionality.
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: c68df2e7be ("mac80211: allow using AP_LINK_PS with mac80211-generated TIM IE")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is a workaround for VHT-enabled STAs which break the spec
and have the VHT-MCS Rx map filled in with value 3 for all eight
spacial streams, an example is AR9462 in AP mode.
As per spec, in section 22.1.1 Introduction to the VHT PHY
A VHT STA shall support at least single spactial stream VHT-MCSs
0 to 7 (transmit and receive) in all supported channel widths.
Some devices in STA mode will get firmware assert when trying to
associate, examples are QCA9377 & QCA6174.
Packet example of broken VHT Cap IE of AR9462:
Tag: VHT Capabilities (IEEE Std 802.11ac/D3.1)
Tag Number: VHT Capabilities (IEEE Std 802.11ac/D3.1) (191)
Tag length: 12
VHT Capabilities Info: 0x00000000
VHT Supported MCS Set
Rx MCS Map: 0xffff
.... .... .... ..11 = Rx 1 SS: Not Supported (0x0003)
.... .... .... 11.. = Rx 2 SS: Not Supported (0x0003)
.... .... ..11 .... = Rx 3 SS: Not Supported (0x0003)
.... .... 11.. .... = Rx 4 SS: Not Supported (0x0003)
.... ..11 .... .... = Rx 5 SS: Not Supported (0x0003)
.... 11.. .... .... = Rx 6 SS: Not Supported (0x0003)
..11 .... .... .... = Rx 7 SS: Not Supported (0x0003)
11.. .... .... .... = Rx 8 SS: Not Supported (0x0003)
...0 0000 0000 0000 = Rx Highest Long GI Data Rate (in Mb/s, 0 = subfield not in use): 0x0000
Tx MCS Map: 0xffff
...0 0000 0000 0000 = Tx Highest Long GI Data Rate (in Mb/s, 0 = subfield not in use): 0x0000
Signed-off-by: Filip Matusiak <filip.matusiak@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
1) Fix off by one wrt. indexing when dumping /proc/net/route entries,
from Alexander Duyck.
2) Fix lockdep splats in iwlwifi, from Johannes Berg.
3) Cure panic when inserting certain netfilter rules when NFT_SET_HASH
is disabled, from Liping Zhang.
4) Memory leak when nft_expr_clone() fails, also from Liping Zhang.
5) Disable UFO when path will apply IPSEC tranformations, from Jakub
Sitnicki.
6) Don't bogusly double cwnd in dctcp module, from Florian Westphal.
7) skb_checksum_help() should never actually use the value "0" for the
resulting checksum, that has a special meaning, use CSUM_MANGLED_0
instead. From Eric Dumazet.
8) Per-tx/rx queue statistic strings are wrong in qed driver, fix from
Yuval MIntz.
9) Fix SCTP reference counting of associations and transports in
sctp_diag. From Xin Long.
10) When we hit ip6tunnel_xmit() we could have come from an ipv4 path in
a previous layer or similar, so explicitly clear the ipv6 control
block in the skb. From Eli Cooper.
11) Fix bogus sleeping inside of inet_wait_for_connect(), from WANG
Cong.
12) Correct deivce ID of T6 adapter in cxgb4 driver, from Hariprasad
Shenai.
13) Fix potential access past the end of the skb page frag array in
tcp_sendmsg(). From Eric Dumazet.
14) 'skb' can legitimately be NULL in inet{,6}_exact_dif_match(). Fix
from David Ahern.
15) Don't return an error in tcp_sendmsg() if we wronte any bytes
successfully, from Eric Dumazet.
16) Extraneous unlocks in netlink_diag_dump(), we removed the locking
but forgot to purge these unlock calls. From Eric Dumazet.
17) Fix memory leak in error path of __genl_register_family(). We leak
the attrbuf, from WANG Cong.
18) cgroupstats netlink policy table is mis-sized, from WANG Cong.
19) Several XDP bug fixes in mlx5, from Saeed Mahameed.
20) Fix several device refcount leaks in network drivers, from Johan
Hovold.
21) icmp6_send() should use skb dst device not skb->dev to determine L3
routing domain. From David Ahern.
22) ip_vs_genl_family sets maxattr incorrectly, from WANG Cong.
23) We leak new macvlan port in some cases of maclan_common_netlink()
errors. Fix from Gao Feng.
24) Similar to the icmp6_send() fix, icmp_route_lookup() should
determine L3 routing domain using skb_dst(skb)->dev not skb->dev.
Also from David Ahern.
25) Several fixes for route offloading and FIB notification handling in
mlxsw driver, from Jiri Pirko.
26) Properly cap __skb_flow_dissect()'s return value, from Eric Dumazet.
27) Fix long standing regression in ipv4 redirect handling, wrt.
validating the new neighbour's reachability. From Stephen Suryaputra
Lin.
28) If sk_filter() trims the packet excessively, handle it reasonably in
tcp input instead of exploding. From Eric Dumazet.
29) Fix handling of napi hash state when copying channels in sfc driver,
from Bert Kenward.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (121 commits)
mlxsw: spectrum_router: Flush FIB tables during fini
net: stmmac: Fix lack of link transition for fixed PHYs
sctp: change sk state only when it has assocs in sctp_shutdown
bnx2: Wait for in-flight DMA to complete at probe stage
Revert "bnx2: Reset device during driver initialization"
ps3_gelic: fix spelling mistake in debug message
net: ethernet: ixp4xx_eth: fix spelling mistake in debug message
ibmvnic: Fix size of debugfs name buffer
ibmvnic: Unmap ibmvnic_statistics structure
sfc: clear napi_hash state when copying channels
mlxsw: spectrum_router: Correctly dump neighbour activity
mlxsw: spectrum: Fix refcount bug on span entries
bnxt_en: Fix VF virtual link state.
bnxt_en: Fix ring arithmetic in bnxt_setup_tc().
Revert "include/uapi/linux/atm_zatm.h: include linux/time.h"
tcp: take care of truncations done by sk_filter()
ipv4: use new_gw for redirect neigh lookup
r8152: Fix error path in open function
net: bpqether.h: remove if_ether.h guard
net: __skb_flow_dissect() must cap its return value
...
Now when users shutdown a sock with SEND_SHUTDOWN in sctp, even if
this sock has no connection (assoc), sk state would be changed to
SCTP_SS_CLOSING, which is not as we expect.
Besides, after that if users try to listen on this sock, kernel
could even panic when it dereference sctp_sk(sk)->bind_hash in
sctp_inet_listen, as bind_hash is null when sock has no assoc.
This patch is to move sk state change after checking sk assocs
is not empty, and also merge these two if() conditions and reduce
indent level.
Fixes: d46e416c11 ("sctp: sctp should change socket state when shutdown is received")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With syzkaller help, Marco Grassi found a bug in TCP stack,
crashing in tcp_collapse()
Root cause is that sk_filter() can truncate the incoming skb,
but TCP stack was not really expecting this to happen.
It probably was expecting a simple DROP or ACCEPT behavior.
We first need to make sure no part of TCP header could be removed.
Then we need to adjust TCP_SKB_CB(skb)->end_seq
Many thanks to syzkaller team and Marco for giving us a reproducer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Marco Grassi <marco.gra@gmail.com>
Reported-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In v2.6, ip_rt_redirect() calls arp_bind_neighbour() which returns 0
and then the state of the neigh for the new_gw is checked. If the state
isn't valid then the redirected route is deleted. This behavior is
maintained up to v3.5.7 by check_peer_redirect() because rt->rt_gateway
is assigned to peer->redirect_learned.a4 before calling
ipv4_neigh_lookup().
After commit 5943634fc5 ("ipv4: Maintain redirect and PMTU info in
struct rtable again."), ipv4_neigh_lookup() is performed without the
rt_gateway assigned to the new_gw. In the case when rt_gateway (old_gw)
isn't zero, the function uses it as the key. The neigh is most likely
valid since the old_gw is the one that sends the ICMP redirect message.
Then the new_gw is assigned to fib_nh_exception. The problem is: the
new_gw ARP may never gets resolved and the traffic is blackholed.
So, use the new_gw for neigh lookup.
Changes from v1:
- use __ipv4_neigh_lookup instead (per Eric Dumazet).
Fixes: 5943634fc5 ("ipv4: Maintain redirect and PMTU info in struct rtable again.")
Signed-off-by: Stephen Suryaputra Lin <ssurya@ieee.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After Tom patch, thoff field could point past the end of the buffer,
this could fool some callers.
If an skb was provided, skb->len should be the upper limit.
If not, hlen is supposed to be the upper limit.
Fixes: a6e544b0a8 ("flow_dissector: Jump to exit code in __skb_flow_dissect")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yibin Yang <yibyang@cisco.com
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the bpf program calls bpf_redirect(dev, 0) and dev is
an ipip/ip6tnl, it currently includes the mac header.
e.g. If dev is ipip, the end result is IP-EthHdr-IP instead
of IP-IP.
The fix is to pull the mac header. At ingress, skb_postpull_rcsum()
is not needed because the ethhdr should have been pulled once already
and then got pushed back just before calling the bpf_prog.
At egress, this patch calls skb_postpull_rcsum().
If bpf_redirect(dev, BPF_F_INGRESS) is called,
it also fails now because it calls dev_forward_skb() which
eventually calls eth_type_trans(skb, dev). The eth_type_trans()
will set skb->type = PACKET_OTHERHOST because the mac address
does not match the redirecting dev->dev_addr. The PACKET_OTHERHOST
will eventually cause the ip_rcv() errors out. To fix this,
____dev_forward_skb() is added.
Joint work with Daniel Borkmann.
Fixes: cfc7381b30 ("ip_tunnel: add collect_md mode to IPIP tunnel")
Fixes: 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
generic_file_splice_read() code that went into -rc1. Switch to the
less efficient default_file_splice_read() for now; the proper fix is
being held for 4.10.
We also have a fix for a 4.8 regression and a trival libceph fixup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJYJdjPAAoJEEp/3jgCEfOLzEoH/A3B1qqiqs2WoMn0O4pnEdcM
TxaU46VOkYcK2wh/xbYAns2kZEXKgcCySv+kXn4l3Gh6/lXVxv4WexNqWdO1o6yN
GqEufIH7yQM6QOE/hkwtUciBXmPfQMPxF14vvprYQuyu5Bs96mrphiAa7vX6Vbk5
VhfE/j0shb8Q2QQj/Om0mWqM6JtOAlr5aFtEcJcodbCk1k8CptUcBsSoQ31PXMC7
UcaBHh1VHGLvx9WeG1Rw1g9tc2LiUyu+UK0csolp51+amB7HezgfmzDQzHtXzBmm
n90SQwonf0DrdWUGuQlOpHnREwxLSgN19s68FCjLc0jeMTP4b6TFEIUgFxiqWc4=
=Ws5s
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-4.9-rc5' of git://github.com/ceph/ceph-client
Pull Ceph fixes from Ilya Dryomov:
"Ceph's ->read_iter() implementation is incompatible with the new
generic_file_splice_read() code that went into -rc1. Switch to the
less efficient default_file_splice_read() for now; the proper fix is
being held for 4.10.
We also have a fix for a 4.8 regression and a trival libceph fixup"
* tag 'ceph-for-4.9-rc5' of git://github.com/ceph/ceph-client:
libceph: initialize last_linger_id with a large integer
libceph: fix legacy layout decode with pool 0
ceph: use default file splice read callback
Jon Paul Maloy
Miroslav Lichvar
David S. Miller
Roman Mashak
Eric Dumazet
Paolo Abeni
WANG Cong
Zhang Shengju
Oliver Hartkopp
Johan Hedberg
Linus Torvalds
Florian Westphal
Gao Feng
Guillaume Nault
Sabrina Dubroca
Johannes Berg
Andreas Gruenbacher
Alexander Duyck
Pablo Neira
Hangbin Liu
Felix Fietkau
Pedersen, Thomas
Filip Matusiak
Xin Long
Scott Mayhew
Stephen Suryaputra Lin
Martin KaFai Lau