usb_kbd_event() and usb_kbd_led() can be called concurrently, but they are not
synchronized. They both readwrite kbd->leds, and usb_kbd_event() originally just
checked the URB status field, while urb.h states that "It [status field] should
not be examined before the URB is returned to the completion handler."
To fix this unsynchronized behavior, this patch introduces a boolean
representing whether the URB is submitted, and a spinlock.
Signed-off-by: Willem Penninckx <willem.penninckx@cs.kuleuven.be>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Newer bluetooth stack supports the NO_INIT_REPORTS quirk. The wiimote does not
support report initialization so enable it by default.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The version number is not needed at all for in-tree drivers. Upstream git is
used to track module versions.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Keep track of current drm and add new debugfs file which reads or writes the
current DRM.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote provides direct access to parts of its eeprom. This implements read
support for small chunks of the eeprom. This isn't very fast but prevents the
reader from blocking the wiimote stream for too long.
Write support is not yet supported as the wiimote breaks if we overwrite its
memory. Use hidraw to reverse-engineer the eeprom before implementing write
support here.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add initializer and deinitializer for debugfs support. This will later allow raw
eeprom access and direct DRM modifications to debug wiimote behaviour and
further protocol reverse-engineerings.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Nintendo Classic Controller extension reports lots of keys, two analog sticks
and two analog buttons. We report all data through extension input device to
userspace.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Nintendo Nunchuck extension reports accelerometer values, one analog stick
and two buttons. See inline comments for data layout.
We report all data to userspace through extension input device.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Motion+ reports rotation gyro data which we report to userspace as ABS_RX/Y/Z
values. The device reports them either in fast or slow mode. We adjust the
values to get a linear scale so userspace does not need to know about slow and
fast mode.
The motion+ also reports whether an extension is connected to it. We keep track
of this value and reinitialize the extensions if an extension is plugged or
unplugged.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All supported extensions report data as 6 byte block. All DRMs with extension
data provide at least 6 extension bytes. Hence a generic handler for all
extension bytes is sufficient and can be called on all DRMs.
The handler distinguishes the input and passes it to the right handler. Motion+
passes data interleaved so we can have Motion+ and a regular extension enabled
simultaneously.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Motion+ and regular extensions are physical adapters for the wiimote so create
one input device for each of them. This also allows to enable only opened
extensions and turn unused extenions off to save battery power.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add new sysfs attribute "extension" which returns the currently connected and
initialized extensions.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote extension registers are not fully understood, so we always disable
all extensions on extension-port events. Then we reinitialize and reidentify
them and activate all requested extensions.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add stub functions to read and identify extensions and then initialize all
connected extensions.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote supports several extensions. This adds a separate source file which
handles all extensions and can be disabled at compile-time.
The driver reacts on "plug"-events on the extension port and starts a worker
which initializes or deinitializes the extensions.
Currently, the initialization logic is not fully understood and we can only
detect and enable all extensions when all extensions are deactivated. Therefore,
we need to disable all extensions, then detect and activate them again to react
on "plug"-events.
However, deactivating extensions will generate a new "plug"-event and we will
never leave that loop. Hence, we only support extensions if they are plugged
before the wiimote is connected (or before the ext-input device is opened). In
the future we may support full extension hotplug support, but
reverse-engineering this may take a while.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add helper functions similar to the write-mem helpers but for reading wiimote
memory and eeprom.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wiimote extension and sound support need access to several symbols so move them
into a new header.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Extension and sound support for the wiimote are quite complex and will be
implemented in separate source files. Hence rename the current driver to "-core"
suffix so multiple files can be linked into this module.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rename the Kconfig entry for hyperv mouse driver so that it has
HID_ prefix as all the other drivers; while at it, place the entry
for this driver to properly ordered place in Makefile and Kconfig.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The file hid-hyperv.c implements a hid compliant mouse driver for use on a
Hyper-V based system. This driver is currently in the staging area and as part
of the effort to move this driver out of staging, I had posted the driver code
for community review a few weeks ago. This current patch addresses all the
review comments I have gotten to date. All the relevant patches have already
been submitted to the staging tree as well.
As per Greg's suggestion, this patch does not get rid of the code from
the staging area. Once the mouse driver lands under the hid directory,
we will cleanup the staging directory.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The USB HID Usage Tables spec defines page 6 for Generic Device Controls, the
most useful of which (to me) is Battery Strength.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This converts the drivers in drivers/hid/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
HID 1.11 specification, section 5.10 tells us:
HID class devices support the ability to ignore selected fields in a
report at run- time. This is accomplished by declaring bit field in a
report that is capable of containing a range of values larger than
those actually generated by the control. If the host or the device
receives an out-of-range value then the current value for the
respective control will not be modified.
So we shouldn't be restricted to EV_ABS only.
Reported-by: Denilson Figueiredo de Sá <denilsonsa@gmail.com>
Tested-by: Denilson Figueiredo de Sá <denilsonsa@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Linux should ignore values outside logical min/max range, as they are not
meaningful. This is what at least some of other OSes do, and it also makes
sense (currently the value gets misinterpreted larger up the stack).
Reported-by: Denilson Figueiredo de Sá <denilsonsa@gmail.com>
Tested-by: Denilson Figueiredo de Sá <denilsonsa@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is very basic driver for Wacom Intuos4 Wireless tablet. It supports only
position, pressure and pen buttons. More features will be added in the future.
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Acked-by: Ping Cheng <pinglinux@gmail.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch doesn't change the way driver works. Parsing logic is now in a
separate function. It's a first step to add Intuos4 Wireless support to
hid-wacom driver.
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Acked-by: Ping Cheng <pinglinux@gmail.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Casting (void *) value returned by kmalloc is useless
as mentioned in Documentation/CodingStyle, Chap 14.
The semantic patch that makes this change is available
in scripts/coccinelle/api/alloc/drop_kmalloc_cast.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
This removes the use of the special "macbookair_fn_keys" keyboard
translation table for the MacBookAir4,x models (ie the 2011 refresh).
They use the standard apple_fn_keys[] translation. Apparently only the
old MacBook Air's need a different translation table.
This mirrors the change that commit da617c7cb9 ("HID: consolidate
MacbookAir 4,1 mappings") did for the WELLSPRING6A ones, but does it for
the WELLSPRING6 model used on the MacBookAir4,2.
Reported-and-tested-by: Dirk Hohndel <hohndel@infradead.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Joshua V Dillon <jvdillon@gmail.com>
Cc: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
Revert "HID: multitouch: decide if hid-multitouch needs to handle mt devices"
HID: drivers/hid/hid-roccat.c: eliminate a null pointer dereference
HID: hid-apple: add device ID of another wireless aluminium
HID: Add device IDs for Macbook Pro 8 keyboards
This reverts commit 0db3bfc72a (""HID: multitouch: decide if hid-multitouch
needs to handle mt devices").
The generic detection of hid-mt devices has two major flaws, and was
merged prematurely. Firstly, the hid-multitouch gets loaded even when
the device is handled by a special device. Secondly, the patch only
partially duplicates the device whitelist already present in hid-core,
effectively rendering a number of devices non-functional.
Reported-by: Sean Young <sean@mess.org>
Tested-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is not possible to take the lock in device if device is NULL.
The mutex_lock is thus moved after the NULL test. New error handling
labels are added at the end to differentiate between the cases where
different sets of locks should be unlocks, and between whether or not
reader should be freed (only on error).
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression E, E1;
identifier f;
statement S1,S2,S3;
@@
if (E == NULL)
{
... when != if (E == NULL || ...) S1 else S2
when != E = E1
*E->f
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in clocksource
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
I've recently bought a Apple wireless aluminum keyboard (model 2011) which is
not yet supported by the kernel - it seems they just changed the device id.
After applying the attached patch, the device is fully functional.
Signed-off-by: Andreas Krist <andreas.krist@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds keyboard support for Macbook Pro 8 models which has
WELLSPRING5A model name and 0x0252, 0x0253 and 0x0254 USB IDs. Trackpad
support for those models are added to bcm5974 in
c331eb580a ("Input: bcm5974 - Add
support for newer MacBookPro8,2).
Signed-off-by: Gökçen Eraslan <gokcen@pardus.org.tr>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
PM / Clocks: Remove redundant NULL checks before kfree()
PM / Documentation: Update docs about suspend and CPU hotplug
ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
PM / Hibernate: Do not initialize static and extern variables to 0
PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
PM / Hibernate: Add resumedelay kernel param in addition to resumewait
MAINTAINERS: Update linux-pm list address
PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
PM / Hibernate: Fix typo in a kerneldoc comment
PM / Hibernate: Freeze kernel threads after preallocating memory
PM: Update the policy on default wakeup settings
PM / VT: Cleanup #if defined uglyness and fix compile error
PM / Suspend: Off by one in pm_suspend()
PM / Hibernate: Include storage keys in hibernation image on s390
...
hid-magicmouse was advertising the Apple Magic Trackpad as having 2
buttons (left and right) when it actually only has 1 button.
Advertising multiple buttons makes Xorg disable all button 2 and 3
emulation (using multi-finger clicks). So Xorg users don't get working
right/middle-click emulation out of the box.
This patch makes hid-magicmouse correctly only report one real button
for Magic Trackpad, which in turn makes Xorg enable multi-finger click
support to emulate right/middle buttons.
[http://launchpad.net/bugs/862094]
Signed-off-by: Daniel van Vugt <vanvugt@gmail.com>
Reviewed-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Support the following models: Super Joy Box 3 Pro, Super Dual Box Pro
and Super Joy Box 5 Pro. These models have support for pressure
sensitive buttons and they can force the controller to either digital
or analog mode, both of which are not supported yet.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove Kconfig dependency for hid-primax driver on CONFIG_EXPERT.
Please see changelog of 73d5e8f77e ("HID: fix up 'EMBEDDED' mess in
Kconfig") for reasoning behind this.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Primax keyboards with the issue this driver addresses report modifier
keys as in band key events instead of as out of band modifier bits,
resulting in the modifier keys generating key up events immediately
before the keys they are intended to modify. This driver rewrites
the raw report data from such keyboards into USB HID 1.11 compliant
report data. It only matches the USB vendor and product IDs for the
keyboard it has been tested on. Since there are several keyboards,
notably a number of laptops and folding USB keyboards known to have
similar unresolved problem reports, the list is expected to grow.
Signed-off-by: Terry Lambert <tlambert@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This makes sure IO is never restarted while a reset is going on
In particular there seems to be no protection from hid_retry_timeout() calling
hid_start_in() which would start IO after hid_pre_reset() has already called
hid_cease_io() because that uses del_timer(), not del_timer_sync()
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We shouldn't change the event flags of input devices after they get registered.
Otherwise, udev will not get notified of these flags and cannot setup the
devices properly.
This fixes the probing to set the input event flags on the input_mapped callback
instead of the probe function.
Reported-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* pm-runtime:
PM / Tracing: build rpm-traces.c only if CONFIG_PM_RUNTIME is set
PM / Runtime: Replace dev_dbg() with trace_rpm_*()
PM / Runtime: Introduce trace points for tracing rpm_* functions
PM / Runtime: Don't run callbacks under lock for power.irq_safe set
USB: Add wakeup info to debugging messages
PM / Runtime: pm_runtime_idle() can be called in atomic context
PM / Runtime: Add macro to test for runtime PM events
PM / Runtime: Add might_sleep() to runtime PM functions
The respective mouse devices are already supported by bcm5974. Now that
Nobuhiro Iwamatsu added support for keyboard to hid-apple driver, we need
to ignore the mouse interfaces of these so that they can still be properly
claimed by bcm5974 driver.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In hidraw_open, if hid_hw_power returns with error, hidraw device open count
should not increase.
Signed-off-by: Amit Nagal <helloin.amit@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Smatch has a new check for Rosenberg type information leaks where
structs are copied to the user with uninitialized stack data in them.
In this case, the hiddev_devinfo struct has a two byte hole.
struct hiddev_devinfo {
__u32 bustype; /* 0 4 */
__u32 busnum; /* 4 4 */
__u32 devnum; /* 8 4 */
__u32 ifnum; /* 12 4 */
__s16 vendor; /* 16 2 */
__s16 product; /* 18 2 */
__s16 version; /* 20 2 */
/* XXX 2 bytes hole, try to pack */
__u32 num_applications; /* 24 4 */
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that hid-generic ignores all win7 compatible multitouch devices, this patch
allows hid-multitouch to catch them. The idea is to rely on the quirk
HID_QUIRK_MULTITOUCH to drop the device if no ContactID is given.
There is the need for a blacklist here as other devices may need a special
driver (ntrig for instance).
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As mentioned by http://www.microsoft.com/whdc/device/input/DigitizerDrvs_touch.mspx
multitouch devices are those that have the input report HID_CONTACTID.
This patch detects this and unloads the generic-usb driver.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There's been a small oversight when adding support for Logitech Driving Force
GT. Entry in hid-core was missing so the generic driver instead of hid-logitech
was being used.
Signed-off-by: Michal Malý <madcatxster@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a bug where a device with index 6 would write out of bounds in
the array of paired devices.
This patch fixes that problem.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Olivier Gay <ogay@logitech.com>
Signed-off-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The function hidraw_disconnect() only acquires the hidraw minors_lock
when clearing the entry in hidraw_table. However the device_destroy()
call can cause a userland read/write to return with an error. It may
cause the program to release the file descripter before the disconnect
is finished. hidraw_disconnect() has already set hidraw->exist to 0,
which makes hidraw_release() kfree the hidraw structure, which
hidraw_disconnect() continues to access and even tries to kfree again.
Similarly if a hidraw_release() occurs after setting hidraw->exist to 0,
the same thing can happen.
This is fixed by expanding the mutex critical section to cover the whole
function from setting hidraw->exist to 0 to freeing the hidraw
structure, preventing a hidraw_release() from interfering.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Tested-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The IDEACOM 6650 multitouch chip, present in various all-in-one computers,
uses the serial version of the HID multitouch protocol. No existing class
supports this.
In principle, the new MT_CLS_SERIAL should work for other
serial panels as well, perhaps including some eGalax panels.
Signed-off-by: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
With this driver, all the devices paired to a single Unifying
receiver are exposed to user processes in separated /input/dev
nodes.
Keyboards with different layouts can be treated differently,
Multiplayer games on single PC (like home theater PC) can
differentiate input coming from different kbds paired to the
same receiver.
Up to now, when Logitech Unifying receivers are connected to a
Linux based system, a single keyboard and a single mouse are
presented to the HID Layer, even if the Unifying receiver can
pair up to six compatible devices. The Unifying receiver by default
multiplexes all incoming events (from multiple keyboards/mice)
into these two.
Signed-off-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds INPUT_PROP_POINTER or INPUT_PROP_DIRECT as necessary to the
hardware supported by the Wacom driver. The DIRECT property is
assigned to devices with an embedded screen (i.e. touchscreens
and display tablets). The POINTER property is assigned to those
without embedded screens.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In function hidraw_open struct hidraw_list *list should be freed for
all error conditions.
Signed-off-by: Amit Nagal <helloin.amit@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Profile changes were only reported when issued mouse internal. Now all
changes are reported.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Introduced function kone_profile_activated() to reduce code duplication.
This by the way fixes a wrong initialization value.
Also fixes early mutex unlocks.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Profile changes were only reported when issued mouse internal. Now all
changes are reported.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Profile changes were only reported when issued mouse internal. Now all
changes are reported.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Actual dpi resolution was set on wrong occassion.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID devices can be hotplugged so we should unregister all sysfs attributes when
removing a driver. Otherwise, manually unloading the wacom-driver will not
remove the sysfs attributes. Only when the device is disconnected, they are
removed, eventually.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
power_supply_unregister() must not be called if power_supply_register() failed.
The wdata->psy.dev pointer may point to invalid memory after a failed
power_supply_register() and hence wacom_remove() will fail while calling
power_supply_unregister().
This changes the wacom_probe function to fail if it cannot register the
power_supply devices. If we would want to keep the previous behaviour we had to
keep some flag about the power_supply state and check it on wacom_remove, but
this seems inappropriate here. Hence, we simply fail, too, if
power_supply_register fails.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add entry to MAINTAINERS and also bump version level as the core driver is
feature complete now.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This registers a power_supply device for every remote to retrieve the current
battery charge level. Since this information is not sent by the wiimote
continously, we need to explicitely request it.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote does not send status reports continuously so this adds a helper
function to request a status report and parses the battery charge level.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Initialize the IR cam if the related input device is opened by userspace. Stop
IR cam again if userspace is no longer interested in its data events.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote IR cam needs a fairly complex initialization sequence. This adds a
helper function that performs IR initialization synchronously.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add helpers to synchronously write registers of the wiimote. This is heavily
used by initialization functions for wiimote peripherals.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To initialize wiimote peripherals, the stream to the wiimote must be held
exclusively by the initializer, otherwise the initialization will fail. Many
initializations require multiple memory requests to be sent synchronously so we
need a way to lock the stream and release it when we are done.
This adds several helper functions which allow to lock the stream, then send
requests, wait for the answers and release the stream again.
When holding the lock, the function may sleep and interrupted by signals.
Also it returns after a short timeout so userspace shouldn't notice long
delays.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote allows direct access to its memory mapped registers and
internal eeprom. This adds support to access this memory and handle
memory events.
There are two macros which wrap up the memory access functions to avoid
accidentally overwriting sensitive eeprom data because a boolean value
was wrongly set.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If an extension is connected the wiimote may report data though DRMs that
contain extension data. This adds handlers for these DRMs but discards extension
data since we do not support it, yet.
It prints a warning to kernel log if an unhandled report is catched. Since we
handle all requests now, this should never happen, though.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Parse IR data and report it to IR input-device. IR data is sent in 3 different
formats, but we only support the basic format as there is no way to send the
additional information to userspace.
All three formats are compatible with the basic IR data format so we need only
one parser.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The IR cam of the wiimote reports 4 trackable lights as absolute values. Since
we can turn the IR cam on and off, we register a separate input device so we can
react on open/close callbacks to save wiimote battery power when IR cam is not
needed.
The cam can be in four states: off, basic, extended and full
The DRM chooser automatically selects a proper DRM that includes all required IR
data so no information is lost.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add parser functions for accelerometer data reported by the wiimote. The data is
almost always reported in the same format, so we can use a single handler.
However, an own handler function is created for each DRM-mode because when IR
and extension support is added, each of them is parsed differently.
Also set the appropriate DRM including accelerometer data on DRM requests to
actually retrieve the accelerometer data.
Data is reported to userspace as ABS_RX/Y/Z values. The values are between -500
and 500 and 0 means no acceleration. See also userspace xwiimote library for
data parsing.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add new input device for every wiimote which is used to report accelerometer
data to userspace. Only if the input device is currently open, we make the
wiimote send accelerometer data. This saves a whole lot of energy on the wiimote
if an application is only interested in button input reports.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote has a single rumble motor. This adds force feedback support for
wiimote devices with FF_RUMBLE. The rumble motor is very simple and only
supports an on/off switch so no complex ff-effects are supported.
This also removes the event callback that was registered before but unused. The
ff-device overwrites this callback, anyway.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds support for the wiimote's rumble device. Every output report can
enable and disable the rumble motor. Hence, every output report must look up our
new RUMBLE flag and make sure that it does not unintentionally toggle the
rumble motor.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is basically a more generic respin of 23746a6 ("HID: magicmouse: ignore
'ivalid report id' while switching modes") which got reverted later by
c3a492.
It turns out that on some configurations, this is actually still the case
and we are not able to detect in runtime.
The device reponds with 'invalid report id' when feature report switching it
into multitouch mode is sent to it.
This has been silently ignored before 0825411ade ("HID: bt: Wait for ACK
on Sent Reports"), but since this commit, it propagates -EIO from the _raw
callback .
So let the driver ignore -EIO as response to 0xd7,0x01 report, as that's
how the device reacts in normal mode.
Sad, but following reality.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=35022
Reported-by: Chase Douglas <chase.douglas@canonical.com>
Reported-by: Jaikumar Ganesh <jaikumarg@android.com>
Tested-by: Chase Douglas <chase.douglas@canonical.com>
Tested-by: Jaikumar Ganesh <jaikumarg@android.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We recently introduced locking into this function, but we missed an
error path which needs an unlock.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote resets the current drm when an extension is plugged in.
Fortunately, it also sends a status report in this situation so we just
reset the drm on every status report to keep the drm consistent.
Also handle return reports from the wiimote which indicate success and
failure of requests that we've sent.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote reports data in several data reporting modes (DRM). The DRM
request makes the wiimote send data in the requested drm.
The DRM mode can be set explicitely or can be chosen by the driver. To let
the driver choose the DRM mode, pass WIIPROTO_REQ_NULL placeholder to it. This
is no valid request and is replaced with an appropriate DRM.
Currently, the driver always sets the basic DRM_K mode, but this will be
extended when further peripherals like accelerometer and IR are supported.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This registers 4 led devices to allow controlling the wiimote leds via standard
LED sysfs API. It removes the four sysfs attributes so we don't have two APIs
for one device.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Even though the bluetooth hid backend does not react on open/close callbacks, we
should call them to be consistent with other hid drivers.
Also the new input open/close handlers will be used in future to prepare the
wiimote device for IR/extension input.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The new locking scheme in HID core allows us to remove a bit of synchronization.
Since the HID layer acts synchronously we simply register input core last and
there are no synchonization issues anymore.
Also register sysfs files after that to simplify the code.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a small rare potential memory leak here. Also Walter Harms
points out that we can do a small cleanup as well by using kstrdup().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Willem Penninckx
Jiri Kosina
David Herrmann
K. Y. Srinivasan
Dan Delaney
Thomas Meyer
Jeremy Fitzhardinge
Greg Kroah-Hartman
Chase Douglas
Przemo Firszt
Linus Torvalds
Henrik Rydberg
Julia Lawall
Paul Gortmaker
Andreas Krist
Gökçen Eraslan
Daniel van Vugt
Sean Young
Terry Lambert
Oliver Neukum
Rafael J. Wysocki
Nobuhiro Iwamatsu
Amit Nagal
Dan Carpenter
Benjamin Tissoires
Michal Malý
Nestor Lopez Casado
James Hogan
Stephane Chatty
Jason Gerecke
Stefan Achatz
Clemens Werther
Dan Carpenter