When a batch of stripes is broken up, we keep some of the flags
that were per-stripe, and copy other flags from the head to all
others.
This only happens while a stripe is being handled, so many of the
flags are irrelevant.
The "SYNC_FLAGS" (which I've renamed to make it clear there are
several) and STRIPE_DEGRADED are set per-stripe and so need to be
preserved. STRIPE_INSYNC is the only flag that is set on the head
that needs to be propagated to all others.
For safety, add a WARN_ON if others are set, except:
STRIPE_HANDLE - this is safe and per-stripe and we are going to set
in several cases anyway
STRIPE_INSYNC
STRIPE_IO_STARTED - this is just a hint and doesn't hurt.
STRIPE_ON_PLUG_LIST
STRIPE_ON_RELEASE_LIST - It is a point pointless for a batched
stripe to be on one of these lists, but it can happen
as can be safely ignored.
Signed-off-by: NeilBrown <neilb@suse.de>
When we add a write to a stripe we need to make sure the bitmap
bit is set. While doing that the stripe is not locked so it could
be added to a batch after which further changes to STRIPE_BIT_DELAY
and ->bm_seq are ineffective.
So we need to hold off adding to a stripe until bitmap_startwrite has
completed at least once, and we need to avoid further changes to
STRIPE_BIT_DELAY once the stripe has been added to a batch.
If a bitmap_startwrite() completes after the stripe was added to a
batch, it will not have set the bit, only incremented a counter, so no
extra delay of the stripe is needed.
Reported-by: Shaohua Li <shli@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.de>
The default setting of 256 stripe_heads is probably
much too small for many configurations. So it is best to make it
auto-configure.
Shrinking the cache under memory pressure is easy. The only
interesting part here is that we put a fairly high cost
('seeks') on shrinking the cache as the cost is greater than
just having to read more data, it reduces parallelism.
Growing the cache on demand needs to be done carefully. If we allow
fast growth, that can upset memory balance as lots of dirty memory can
quickly turn into lots of memory queued in the stripe_cache.
It is important for the raid5 block device to appear congested to
allow write-throttling to work.
So we only add stripes slowly. We set a flag when an allocation
fails because all stripes are in use, allocate at a convenient
time when that flag is set, and don't allow it to be set again
until at least one stripe_head has been released for re-use.
This means that a spurt of requests will only cause one stripe_head
to be allocated, but a steady stream of requests will slowly
increase the cache size - until memory pressure puts it back again.
It could take hours to reach a steady state.
The value written to, and displayed in, stripe_cache_size is
used as a minimum. The cache can grow above this and shrink back
down to it. The actual size is not directly visible, though it can
be deduced to some extent by watching stripe_cache_active.
Signed-off-by: NeilBrown <neilb@suse.de>
Depending on the available coding we allow optimized rmw logic for write
operations. To support easier testing this patch allows manual control
of the rmw/rcw descision through the interface /sys/block/mdX/md/rmw_level.
The configuration can handle three levels of control.
rmw_level=0: Disable rmw for all RAID types. Hardware assisted P/Q
calculation has no implementation path yet to factor in/out chunks of
a syndrome. Enforcing this level can be benefical for slow CPUs with
hardware syndrome support and fast SSDs.
rmw_level=1: Estimate rmw IOs and rcw IOs. Execute rmw only if we will
save IOs. This equals the "old" unpatched behaviour and will be the
default.
rmw_level=2: Execute rmw even if calculated IOs for rmw and rcw are
equal. We might have higher CPU consumption because of calculating the
parity twice but it can be benefical otherwise. E.g. RAID4 with fast
dedicated parity disk/SSD. The option is implemented just to be
forward-looking and will ONLY work with this patch!
Signed-off-by: Markus Stockhausen <stockhausen@collogia.de>
Signed-off-by: NeilBrown <neilb@suse.de>
Glue it altogehter. The raid6 rmw path should work the same as the
already existing raid5 logic. So emulate the prexor handling/flags
and split functions as needed.
1) Enable xor_syndrome() in the async layer.
2) Split ops_run_prexor() into RAID4/5 and RAID6 logic. Xor the syndrome
at the start of a rmw run as we did it before for the single parity.
3) Take care of rmw run in ops_run_reconstruct6(). Again process only
the changed pages to get syndrome back into sync.
4) Enhance set_syndrome_sources() to fill NULL pages if we are in a rmw
run. The lower layers will calculate start & end pages from that and
call the xor_syndrome() correspondingly.
5) Adapt the several places where we ignored Q handling up to now.
Performance numbers for a single E5630 system with a mix of 10 7200k
desktop/server disks. 300 seconds random write with 8 threads onto a
3,2TB (10*400GB) RAID6 64K chunk without spare (group_thread_cnt=4)
bsize rmw_level=1 rmw_level=0 rmw_level=1 rmw_level=0
skip_copy=1 skip_copy=1 skip_copy=0 skip_copy=0
4K 115 KB/s 141 KB/s 165 KB/s 140 KB/s
8K 225 KB/s 275 KB/s 324 KB/s 274 KB/s
16K 434 KB/s 536 KB/s 640 KB/s 534 KB/s
32K 751 KB/s 1,051 KB/s 1,234 KB/s 1,045 KB/s
64K 1,339 KB/s 1,958 KB/s 2,282 KB/s 1,962 KB/s
128K 2,673 KB/s 3,862 KB/s 4,113 KB/s 3,898 KB/s
256K 7,685 KB/s 7,539 KB/s 7,557 KB/s 7,638 KB/s
512K 19,556 KB/s 19,558 KB/s 19,652 KB/s 19,688 Kb/s
Signed-off-by: Markus Stockhausen <stockhausen@collogia.de>
Signed-off-by: NeilBrown <neilb@suse.de>
expansion/resync can grab a stripe when the stripe is in batch list. Since all
stripes in batch list must be in the same state, we can't allow some stripes
run into expansion/resync. So we delay expansion/resync for stripe in batch
list.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If io error happens in any stripe of a batch list, the batch list will be
split, then normal process will run for the stripes in the list.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
stripe cache is 4k size. Even adjacent full stripe writes are handled in 4k
unit. Idealy we should use big size for adjacent full stripe writes. Bigger
stripe cache size means less stripes runing in the state machine so can reduce
cpu overhead. And also bigger size can cause bigger IO size dispatched to under
layer disks.
With below patch, we will automatically batch adjacent full stripe write
together. Such stripes will be added to the batch list. Only the first stripe
of the list will be put to handle_list and so run handle_stripe(). Some steps
of handle_stripe() are extended to cover all stripes of the list, including
ops_run_io, ops_run_biodrain and so on. With this patch, we have less stripes
running in handle_stripe() and we send IO of whole stripe list together to
increase IO size.
Stripes added to a batch list have some limitations. A batch list can only
include full stripe write and can't cross chunk boundary to make sure stripes
have the same parity disks. Stripes in a batch list must be in the same state
(no written, toread and so on). If a stripe is in a batch list, all new
read/write to add_stripe_bio will be blocked to overlap conflict till the batch
list is handled. The limitations will make sure stripes in a batch list be in
exactly the same state in the life circly.
I did test running 160k randwrite in a RAID5 array with 32k chunk size and 6
PCIe SSD. This patch improves around 30% performance and IO size to under layer
disk is exactly 32k. I also run a 4k randwrite test in the same array to make
sure the performance isn't changed with the patch.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Track overwrite disk count, so we can know if a stripe is a full stripe write.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
A freshly new stripe with write request can be batched. Any time the stripe is
handled or new read is queued, the flag will be cleared.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Use flex_array for scribble data. Next patch will batch several stripes
together, so scribble data should be able to cover several stripes, so this
patch also allocates scribble data for stripes across a chunk.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
There is currently no locking around calls to the 'congested'
bdi function. If called at an awkward time while an array is
being converted from one level (or personality) to another, there
is a tiny chance of running code in an unreferenced module etc.
So add a 'congested' function to the md_personality operations
structure, and call it with appropriate locking from a central
'mddev_congested'.
When the array personality is changing the array will be 'suspended'
so no IO is processed.
If mddev_congested detects this, it simply reports that the
array is congested, which is a safe guess.
As mddev_suspend calls synchronize_rcu(), mddev_congested can
avoid races by included the whole call inside an rcu_read_lock()
region.
This require that the congested functions for all subordinate devices
can be run under rcu_lock. Fortunately this is the case.
Signed-off-by: NeilBrown <neilb@suse.de>
The stripe cache has two goals:
1. cache data, so next time if data can be found in stripe cache, disk access
can be avoided.
2. stable data. data is copied from bio to stripe cache and calculated parity.
data written to disk is from stripe cache, so if upper layer changes bio data,
data written to disk isn't impacted.
In my environment, I can guarantee 2 will not happen. And BDI_CAP_STABLE_WRITES
can guarantee 2 too. For 1, it's not common too. block plug mechanism will
dispatch a bunch of sequentail small requests together. And since I'm using
SSD, I'm using small chunk size. It's rare case stripe cache is really useful.
So I'd like to avoid the copy from bio to stripe cache and it's very helpful
for performance. In my 1M randwrite tests, avoid the copy can increase the
performance more than 30%.
Of course, this shouldn't be enabled by default. It's reported enabling
BDI_CAP_STABLE_WRITES can harm some workloads before, so I added an option to
control it.
Neilb:
changed BUG_ON to WARN_ON
Removed some assignments from raid5_build_block which are now not needed.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Mostly optimisations and obscure bug fixes.
- raid5 gets less lock contention
- raid1 gets less contention between normal-io and resync-io
during resync.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8RCg
-----END PGP SIGNATURE-----
Merge tag 'md/3.13' of git://neil.brown.name/md
Pull md update from Neil Brown:
"Mostly optimisations and obscure bug fixes.
- raid5 gets less lock contention
- raid1 gets less contention between normal-io and resync-io during
resync"
* tag 'md/3.13' of git://neil.brown.name/md:
md/raid5: Use conf->device_lock protect changing of multi-thread resources.
md/raid5: Before freeing old multi-thread worker, it should flush them.
md/raid5: For stripe with R5_ReadNoMerge, we replace REQ_FLUSH with REQ_NOMERGE.
UAPI: include <asm/byteorder.h> in linux/raid/md_p.h
raid1: Rewrite the implementation of iobarrier.
raid1: Add some macros to make code clearly.
raid1: Replace raise_barrier/lower_barrier with freeze_array/unfreeze_array when reconfiguring the array.
raid1: Add a field array_frozen to indicate whether raid in freeze state.
md: Convert use of typedef ctl_table to struct ctl_table
md/raid5: avoid deadlock when raid5 array has unack badblocks during md_stop_writes.
md: use MD_RECOVERY_INTR instead of kthread_should_stop in resync thread.
md: fix some places where mddev_lock return value is not checked.
raid5: Retry R5_ReadNoMerge flag when hit a read error.
raid5: relieve lock contention in get_active_stripe()
raid5: relieve lock contention in get_active_stripe()
wait: add wait_event_cmd()
md/raid5.c: add proper locking to error path of raid5_start_reshape.
md: fix calculation of stacking limits on level change.
raid5: Use slow_path to release stripe when mddev->thread is null
track empty inactive list count, so md_raid5_congested() can use it to make
decision.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
get_active_stripe() is the last place we have lock contention. It has two
paths. One is stripe isn't found and new stripe is allocated, the other is
stripe is found.
The first path basically calls __find_stripe and init_stripe. It accesses
conf->generation, conf->previous_raid_disks, conf->raid_disks,
conf->prev_chunk_sectors, conf->chunk_sectors, conf->max_degraded,
conf->prev_algo, conf->algorithm, the stripe_hashtbl and inactive_list. Except
stripe_hashtbl and inactive_list, other fields are changed very rarely.
With this patch, we split inactive_list and add new hash locks. Each free
stripe belongs to a specific inactive list. Which inactive list is determined
by stripe's lock_hash. Note, even a stripe hasn't a sector assigned, it has a
lock_hash assigned. Stripe's inactive list is protected by a hash lock, which
is determined by it's lock_hash too. The lock_hash is derivied from current
stripe_hashtbl hash, which guarantees any stripe_hashtbl list will be assigned
to a specific lock_hash, so we can use new hash lock to protect stripe_hashtbl
list too. The goal of the new hash locks introduced is we can only use the new
locks in the first path of get_active_stripe(). Since we have several hash
locks, lock contention is relieved significantly.
The first path of get_active_stripe() accesses other fields, since they are
changed rarely, changing them now need take conf->device_lock and all hash
locks. For a slow path, this isn't a problem.
If we need lock device_lock and hash lock, we always lock hash lock first. The
tricky part is release_stripe and friends. We need take device_lock first.
Neil's suggestion is we put inactive stripes to a temporary list and readd it
to inactive_list after device_lock is released. In this way, we add stripes to
temporary list with device_lock hold and remove stripes from the list with hash
lock hold. So we don't allow concurrent access to the temporary list, which
means we need allocate temporary list for all participants of release_stripe.
One downside is free stripes are maintained in their inactive list, they can't
across between the lists. By default, we have total 256 stripes and 8 lists, so
each list will have 32 stripes. It's possible one list has free stripe but
other list hasn't. The chance should be rare because stripes allocation are
even distributed. And we can always allocate more stripes for cache, several
mega bytes memory isn't a big deal.
This completely removes the lock contention of the first path of
get_active_stripe(). It slows down the second code path a little bit though
because we now need takes two locks, but since the hash lock isn't contended,
the overhead should be quite small (several atomic instructions). The second
path of get_active_stripe() (basically sequential write or big request size
randwrite) still has lock contentions.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If there are not enough stripes to handle, we'd better not always
queue all available work_structs. If one worker can only handle small
or even none stripes, it will impact request merge and create lock
contention.
With this patch, the number of work_struct running will depend on
pending stripes number. Note: some statistics info used in the patch
are accessed without locking protection. This should doesn't matter,
we just try best to avoid queue unnecessary work_struct.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
make_request() access various shape parameters (raid_disks, chunk_size
etc) which might be changed by raid5_start_reshape().
If the later is called at and awkward time during the form, the wrong
stripe_head might be used.
So introduce a 'seqcount' and after finding a stripe_head make sure
there is no reason to expect that we got the wrong one.
Signed-off-by: NeilBrown <neilb@suse.de>
This is another attempt to create multiple threads to handle raid5 stripes.
This time I use workqueue.
raid5 handles request (especially write) in stripe unit. A stripe is page size
aligned/long and acrosses all disks. Writing to any disk sector, raid5 runs a
state machine for the corresponding stripe, which includes reading some disks
of the stripe, calculating parity, and writing some disks of the stripe. The
state machine is running in raid5d thread currently. Since there is only one
thread, it doesn't scale well for high speed storage. An obvious solution is
multi-threading.
To get better performance, we have some requirements:
a. locality. stripe corresponding to request submitted from one cpu is better
handled in thread in local cpu or local node. local cpu is preferred but some
times could be a bottleneck, for example, parity calculation is too heavy.
local node running has wide adaptability.
b. configurablity. Different setup of raid5 array might need diffent
configuration. Especially the thread number. More threads don't always mean
better performance because of lock contentions.
My original implementation is creating some kernel threads. There are
interfaces to control which cpu's stripe each thread should handle. And
userspace can set affinity of the threads. This provides biggest flexibility
and configurability. But it's hard to use and apparently a new thread pool
implementation is disfavor.
Recent workqueue improvement is quite promising. unbound workqueue will be
bound to numa node. If WQ_SYSFS is set in workqueue, there are sysfs option to
do affinity setting. For example, we can only include one HT sibling in
affinity. Since work is non-reentrant by default, and we can control running
thread number by limiting dispatched work_struct number.
In this patch, I created several stripe worker group. A group is a numa node.
stripes from cpus of one node will be added to a group list. Workqueue thread
of one node will only handle stripes of worker group of the node. In this way,
stripe handling has numa node locality. And as I said, we can control thread
number by limiting dispatched work_struct number.
The work_struct callback function handles several stripes in one run. A typical
work queue usage is to run one unit in each work_struct. In raid5 case, the
unit is a stripe. But we can't do that:
a. Though handling a stripe doesn't need lock because of reference accounting
and stripe isn't in any list, queuing a work_struct for each stripe will make
workqueue lock contended very heavily.
b. blk_start_plug()/blk_finish_plug() should surround stripe handle, as we
might dispatch request. If each work_struct only handles one stripe, such block
plug is meaningless.
This implementation can't do very fine grained configuration. But the numa
binding is most popular usage model, should be enough for most workloads.
Note: since we have only one stripe queue, switching to multi-thread might
decrease request size dispatching down to low level layer. The impact depends
on thread number, raid configuration and workload. So multi-thread raid5 might
not be proper for all setups.
Changes V1 -> V2:
1. remove WQ_NON_REENTRANT
2. disabling multi-threading by default
3. Add more descriptions in changelog
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
release_stripe still has big lock contention. We just add the stripe to a llist
without taking device_lock. We let the raid5d thread to do the real stripe
release, which must hold device_lock anyway. In this way, release_stripe
doesn't hold any locks.
The side effect is the released stripes order is changed. But sounds not a big
deal, stripes are never handled in order. And I thought block layer can already
do nice request merge, which means order isn't that important.
I kept the unplug release batch, which is unnecessary with this patch from lock
contention avoid point of view, and actually if we delete it, the stripe_head
release_list and lru can share storage. But the unplug release batch is also
helpful for request merge. We probably can delay wakeup raid5d till unplug, but
I'm still afraid of the case which raid5d is running.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If a device in a RAID4/5/6 is being replaced while another is being
recovered, then the writes to the replacement device currently don't
happen, resulting in corruption when the replacement completes and the
new drive takes over.
This is because the replacement writes are only triggered when
's.replacing' is set and not when the similar 's.sync' is set (which
is the case during resync and recovery - it means all devices need to
be read).
So schedule those writes when s.replacing is set as well.
In this case we cannot use "STRIPE_INSYNC" to record that the
replacement has happened as that is needed for recording that any
parity calculation is complete. So introduce STRIPE_REPLACED to
record if the replacement has happened.
For safety we should also check that STRIPE_COMPUTE_RUN is not set.
This has a similar effect to the "s.locked == 0" test. The latter
ensure that now IO has been flagged but not started. The former
checks if any parity calculation has been flagged by not started.
We must wait for both of these to complete before triggering the
'replace'.
Add a similar test to the subsequent check for "are we finished yet".
This possibly isn't needed (is subsumed in the STRIPE_INSYNC test),
but it makes it more obvious that the REPLACE will happen before we
think we are finished.
Finally if a NeedReplace device is not UPTODATE then that is an
error. We really must trigger a warning.
This bug was introduced in commit 9a3e1101b8
(md/raid5: detect and handle replacements during recovery.)
which introduced replacement for raid5.
That was in 3.3-rc3, so any stable kernel since then would benefit
from this fix.
Cc: stable@vger.kernel.org (3.3+)
Reported-by: qindehua <13691222965@163.com>
Tested-by: qindehua <qindehua@163.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Once instance of this Kconfig macro remained after commit
51acbcec6c ("md: remove
CONFIG_MULTICORE_RAID456"). Remove that one too. And, while we're at it,
also remove it from the defconfig files that carry it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: NeilBrown <neilb@suse.de>
A number of problems can occur due to races between
resync/recovery and discard.
- if sync_request calls handle_stripe() while a discard is
happening on the stripe, it might call handle_stripe_clean_event
before all of the individual discard requests have completed
(so some devices are still locked, but not all).
Since commit ca64cae960
md/raid5: Make sure we clear R5_Discard when discard is finished.
this will cause R5_Discard to be cleared for the parity device,
so handle_stripe_clean_event() will not be called when the other
devices do become unlocked, so their ->written will not be cleared.
This ultimately leads to a WARN_ON in init_stripe and a lock-up.
- If handle_stripe_clean_event() does clear R5_UPTODATE at an awkward
time for resync, it can lead to s->uptodate being less than disks
in handle_parity_checks5(), which triggers a BUG (because it is
one).
So:
- keep R5_Discard on the parity device until all other devices have
completed their discard request
- make sure we don't try to have a 'discard' and a 'sync' action at
the same time.
This involves a new stripe flag to we know when a 'discard' is
happening, and the use of R5_Overlap on the parity disk so when a
discard is wanted while a sync is active, so we know to wake up
the discard at the appropriate time.
Discard support for RAID5 was added in 3.7, so this is suitable for
any -stable kernel since 3.7.
Cc: stable@vger.kernel.org (v3.7+)
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Discard for raid4/5/6 has limitation. If discard request size is
small, we do discard for one disk, but we need calculate parity and
write parity disk. To correctly calculate parity, zero_after_discard
must be guaranteed. Even it's true, we need do discard for one disk
but write another disks, which makes the parity disks wear out
fast. This doesn't make sense. So an efficient discard for raid4/5/6
should discard all data disks and parity disks, which requires the
write pattern to be (A, A+chunk_size, A+chunk_size*2...). If A's size
is smaller than chunk_size, such pattern is almost impossible in
practice. So in this patch, I only handle the case that A's size
equals to chunk_size. That is discard request should be aligned to
stripe size and its size is multiple of stripe size.
Since we can only handle request with specific alignment and size (or
part of the request fitting stripes), we can't guarantee
zero_after_discard even zero_after_discard is true in low level
drives.
The block layer doesn't send down correctly aligned requests even
correct discard alignment is set, so I must filter out.
For raid4/5/6 parity calculation, if data is 0, parity is 0. So if
zero_after_discard is true for all disks, data is consistent after
discard. Otherwise, data might be lost. Let's consider a scenario:
discard a stripe, write data to one disk and write parity disk. The
stripe could be still inconsistent till then depending on using data
from other data disks or parity disks to calculate new parity. If the
disk is broken, we can't restore it. So in this patch, we only enable
discard support if all disks have zero_after_discard.
If discard fails in one disk, we face the similar inconsistent issue
above. The patch will make discard follow the same path as normal
write request. If discard fails, a resync will be scheduled to make
the data consistent. This isn't good to have extra writes, but data
consistency is important.
If a subsequent read/write request hits raid5 cache of a discarded
stripe, the discarded dev page should have zero filled, so the data is
consistent. This patch will always zero dev page for discarded request
stripe. This isn't optimal because discard request doesn't need such
payload. Next patch will avoid it.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This contains a few patches that depend on
plugging changes in the block layer so needs to wait
for those.
It also contains a Kconfig fix for the new RAID10 support
in dm-raid.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=ovN2
-----END PGP SIGNATURE-----
Merge tag 'md-3.6' of git://neil.brown.name/md
Pull additional md update from NeilBrown:
"This contains a few patches that depend on plugging changes in the
block layer so needed to wait for those.
It also contains a Kconfig fix for the new RAID10 support in dm-raid."
* tag 'md-3.6' of git://neil.brown.name/md:
md/dm-raid: DM_RAID should select MD_RAID10
md/raid1: submit IO from originating thread instead of md thread.
raid5: raid5d handle stripe in batch way
raid5: make_request use batch stripe release
make_request() does stripe release for every stripe and the stripe usually has
count 1, which makes previous release_stripe() optimization not work. In my
test, this release_stripe() becomes the heaviest pleace to take
conf->device_lock after previous patches applied.
Below patch makes stripe release batch. All the stripes will be released in
unplug. The STRIPE_ON_UNPLUG_LIST bit is to protect concurrent access stripe
lru.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Because bios will merge at block-layer,so bios-error may caused by other
bio which be merged into to the same request.
Using this flag,it will find exactly error-sector and not do redundant
operation like re-write and re-read.
V0->V1:Using REQ_FLUSH instead REQ_NOMERGE avoid bio merging at block
layer.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Add a per-stripe lock to protect stripe specific data. The purpose is to reduce
lock contention of conf->device_lock.
stripe ->toread, ->towrite are protected by per-stripe lock. Accessing bio
list of the stripe is always serialized by this lock, so adding bio to the
lists (add_stripe_bio()) and removing bio from the lists (like
ops_run_biofill()) not race.
If bio in ->read, ->written ... list are not shared by multiple stripes, we
don't need any lock to protect ->read, ->written, because STRIPE_ACTIVE will
protect them. If the bio are shared, there are two protections:
1. bi_phys_segments acts as a reference count
2. traverse the list uses r5_next_bio, which makes traverse never access bio
not belonging to the stripe
Let's have an example:
| stripe1 | stripe2 | stripe3 |
...bio1......|bio2|bio3|....bio4.....
stripe2 has 4 bios, when it's finished, it will decrement bi_phys_segments for
all bios, but only end_bio for bio2 and bio3. bio1->bi_next still points to
bio2, but this doesn't matter. When stripe1 is finished, it will not touch bio2
because of r5_next_bio check. Next time stripe1 will end_bio for bio1 and
stripe3 will end_bio bio4.
before add_stripe_bio() addes a bio to a stripe, we already increament the bio
bi_phys_segments, so don't worry other stripes release the bio.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
REQ_SYNC is ignored in current raid5 code. Block layer does use it to do
policy,
for example ioscheduler. This patch adds it.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The important issue here is incorporating the different in data_offset
into calculations concerning when we might need to over-write data
that is still thought to be valid.
To this end we find the minimum offset difference across all devices
and add that where appropriate.
Signed-off-by: NeilBrown <neilb@suse.de>
During recovery we want to write to the replacement but not
the original. So we have two new flags
- R5_NeedReplace if this stripe has a replacement that needs to
be written at some stage
- R5_WantReplace if NeedReplace, and the data is available, and
a 'sync' has been requested on this stripe.
We also distinguish between 'sync and replace' which need to read
all other devices, and 'replace' which only needs to read the
devices being replaced.
Note that during resync we always write to any replacement device.
It might not need to be written to, but as we don't read to compare,
we have to write to be sure.
Signed-off-by: NeilBrown <neilb@suse.de>
When writing, we need to submit two writes, one to the original, and
one to the replacement - if there is a replacement.
If the write to the replacement results in a write error, we just fail
the device. We only try to record write errors to the original.
When writing for recovery, we shouldn't write to the original. This
will be addressed in a subsequent patch that generally addresses
recovery.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Remove some #defines that are no longer used, and replace some
others with an enum.
And remove an unused field.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Just enhance data structures to record a second device per slot to be
used as a 'replacement' device, replacing the original.
We also have a second bio in each slot in each stripe_head. This will
only be used when writing to the array - we need to write to both the
original and the replacement at the same time, so will need two bios.
For now, only try using the replacement drive for aligned-reads.
In this case, we prefer the replacement if it has been recovered far
enough, otherwise use the original.
This includes a small enhancement. Previously we would only do
aligned reads if the target device was fully recovered. Now we also
do them if it has recovered far enough.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The typedefs are just annoying. 'mdk' probably refers to 'md_k.h'
which used to be an include file that defined this thing.
Signed-off-by: NeilBrown <neilb@suse.de>
On a successful write to a known bad block, flag the sh
so that raid5d can remove the known bad block from the list.
Signed-off-by: NeilBrown <neilb@suse.de>
When a write error is detected, don't mark the device as failed
immediately but rather record the fact for handle_stripe to deal with.
Handle_stripe then attempts to record a bad block. Only if that fails
does the device get marked as faulty.
Signed-off-by: NeilBrown <neilb@suse.de>
If we get an uncorrectable read error - record a bad block rather than
failing the device.
And if these errors (which may be due to known bad blocks) cause
recovery to be impossible, record a bad block on the recovering
devices, or abort the recovery.
As we might abort a recovery without failing a device we need to teach
RAID5 about recovery_disabled handling.
Signed-off-by: NeilBrown <neilb@suse.de>
Adding these three fields will allow more common code to be moved
to handle_stripe()
struct field rearrangement by Namhyung Kim.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
'struct stripe_head_state' stores state about the 'current' stripe
that is passed around while handling the stripe.
For RAID6 there is an extension structure: r6_state, which is also
passed around.
There is no value in keeping these separate, so move the fields from
the latter into the former.
This means that all code now needs to treat s->failed_num as an small
array, but this is a small cost.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
sh->lock is now mainly used to ensure that two threads aren't running
in the locked part of handle_stripe[56] at the same time.
That can more neatly be achieved with an 'active' flag which we set
while running handle_stripe. If we find the flag is set, we simply
requeue the stripe for later by setting STRIPE_HANDLE.
For safety we take ->device_lock while examining the state of the
stripe and creating a summary in 'stripe_head_state / r6_state'.
This possibly isn't needed but as shared fields like ->toread,
->towrite are checked it is safer for now at least.
We leave the label after the old 'unlock' called "unlock" because it
will disappear in a few patches, so renaming seems pointless.
This leaves the stripe 'locked' for longer as we clear STRIPE_ACTIVE
later, but that is not a problem.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
This is the start of a series of patches to remove sh->lock.
sync_request takes sh->lock before setting STRIPE_SYNCING to ensure
there is no race with testing it in handle_stripe[56].
Instead, use a new flag STRIPE_SYNC_REQUESTED and test it early
in handle_stripe[56] (after getting the same lock) and perform the
same set/clear operations if it was set.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
md has some plugging infrastructure for RAID5 to use because the
normal plugging infrastructure required a 'request_queue', and when
called from dm, RAID5 doesn't have one of those available.
This relied on the ->unplug_fn callback which doesn't exist any more.
So remove all of that code, both in md and raid5. Subsequent patches
with restore the plugging functionality.
Signed-off-by: NeilBrown <neilb@suse.de>
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This patch converts md to support REQ_FLUSH/FUA instead of now
deprecated REQ_HARDBARRIER. In the core part (md.c), the following
changes are notable.
* Unlike REQ_HARDBARRIER, REQ_FLUSH/FUA don't interfere with
processing of other requests and thus there is no reason to mark the
queue congested while FLUSH/FUA is in progress.
* REQ_FLUSH/FUA failures are final and its users don't need retry
logic. Retry logic is removed.
* Preflush needs to be issued to all member devices but FUA writes can
be handled the same way as other writes - their processing can be
deferred to request_queue of member devices. md_barrier_request()
is renamed to md_flush_request() and simplified accordingly.
For linear, raid0 and multipath, the core changes are enough. raid1,
5 and 10 need the following conversions.
* raid1: Handling of FLUSH/FUA bio's can simply be deferred to
request_queues of member devices. Barrier related logic removed.
* raid5: Queue draining logic dropped. FUA bit is propagated through
biodrain and stripe resconstruction such that all the updated parts
of the stripe are written out with FUA writes if any of the dirtying
writes was FUA. preread_active_stripes handling in make_request()
is updated as suggested by Neil Brown.
* raid10: FUA bit needs to be propagated to write clones.
linear, raid0, 1, 5 and 10 tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
md/raid5 uses the plugging infrastructure provided by the block layer
and 'struct request_queue'. However when we plug raid5 under dm there
is no request queue so we cannot use that.
So create a similar infrastructure that is much lighter weight and use
it for raid5.
Signed-off-by: NeilBrown <neilb@suse.de>
the dm module will need this for dm-raid45.
Also only access ->queue->backing_dev_info->congested_fn
if ->queue actually exists. It won't in a dm target.
Signed-off-by: NeilBrown <neilb@suse.de>
We will shortly allow md devices with no gendisk (they are attached to
a dm-target instead). That will cause mdname() to return 'mdX'.
There is one place where mdname really needs to be unique: when
creating the name for a slab cache.
So in that case, if there is no gendisk, you the address of the mddev
formatted in HEX to provide a unique name.
Signed-off-by: NeilBrown <neilb@suse.de>
Add __percpu sparse annotations to places which didn't make it in one
of the previous patches. All converions are trivial.
These annotations are to make sparse consider percpu variables to be
in a different address space and warn if accessed without going
through percpu accessors. This patch doesn't affect normal builds.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Neil Brown <neilb@suse.de>
The percpu conversion allowed a straightforward handoff of stripe
processing to the async subsytem that initially showed some modest gains
(+4%). However, this model is too simplistic and leads to stripes
bouncing between raid5d and the async thread pool for every invocation
of handle_stripe(). As reported by Holger this can fall into a
pathological situation severely impacting throughput (6x performance
loss).
By downleveling the parallelism to raid_run_ops the pathological
stripe_head bouncing is eliminated. This version still exhibits an
average 11% throughput loss for:
mdadm --create /dev/md0 /dev/sd[b-q] -n 16 -l 6
echo 1024 > /sys/block/md0/md/stripe_cache_size
dd if=/dev/zero of=/dev/md0 bs=1024k count=2048
...but the results are at least stable and can be used as a base for
further multicore experimentation.
Reported-by: Holger Kiehl <Holger.Kiehl@dwd.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
[ Based on an original patch by Yuri Tikhonov ]
The raid_run_ops routine uses the asynchronous offload api and
the stripe_operations member of a stripe_head to carry out xor+pq+copy
operations asynchronously, outside the lock.
The operations performed by RAID-6 are the same as in the RAID-5 case
except for no support of STRIPE_OP_PREXOR operations. All the others
are supported:
STRIPE_OP_BIOFILL
- copy data into request buffers to satisfy a read request
STRIPE_OP_COMPUTE_BLK
- generate missing blocks (1 or 2) in the cache from the other blocks
STRIPE_OP_BIODRAIN
- copy data out of request buffers to satisfy a write request
STRIPE_OP_RECONSTRUCT
- recalculate parity for new data that has entered the cache
STRIPE_OP_CHECK
- verify that the parity is correct
The flow is the same as in the RAID-5 case, and reuses some routines, namely:
1/ ops_complete_postxor (renamed to ops_complete_reconstruct)
2/ ops_complete_compute (updated to set up to 2 targets uptodate)
3/ ops_run_check (renamed to ops_run_check_p for xor parity checks)
[neilb@suse.de: fixes to get it to pass mdadm regression suite]
Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Replace the flat zero_sum_result with a collection of flags to contain
the P (xor) zero-sum result, and the soon to be utilized Q (raid6 reed
solomon syndrome) zero-sum result. Use the SUM_CHECK_ namespace instead
of DMA_ since these flags will be used on non-dma-zero-sum enabled
platforms.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use percpu memory rather than stack for storing the buffer lists used in
parity calculations. Include space for dma address conversions and pass
that to async_tx via the async_submit_ctl.scribble pointer.
[ Impact: move memory pressure from stack to heap ]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for asynchronous handling of raid6 operations move the
spare page to a percpu allocation to allow multiple simultaneous
synchronous raid6 recovery operations.
Make this allocation cpu hotplug aware to maximize allocation
efficiency.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Having a macro just to cast a void* isn't really helpful.
I would must rather see that we are simply de-referencing ->private,
than have to know what the macro does.
So open code the macro everywhere and remove the pointless cast.
Signed-off-by: NeilBrown <neilb@suse.de>
We currently update the metadata :
1/ every 3Megabytes
2/ When the place we will write new-layout data to is recorded in
the metadata as still containing old-layout data.
Rule one exists to avoid having to re-do too much reshaping in the
face of a crash/restart. So it should really be time based rather
than size based. So change it to "every 10 seconds".
Rule two turns out to be too harsh when restriping an array
'in-place', as in that case the metadata much be updates for every
stripe.
For the in-place update, it can only possibly be safe from a crash if
some user-space program data a backup of every e.g. few hundred
stripes before allowing them to be reshaped. In that case, the
constant metadata update is pointless.
So only update the metadata if the new metadata will report that the
end of the 'old-layout' data is beyond where we are currently
writing 'new-layout' data.
Signed-off-by: NeilBrown <neilb@suse.de>
Add "prev_chunk" to raid5_conf_t, similar to "previous_raid_disks", to
remember what the chunk size was before the reshape that is currently
underway.
This seems like duplication with "chunk_size" and "new_chunk" in
mddev_t, and to some extent it is, but there are differences.
The values in mddev_t are always defined and often the same.
The prev* values are only defined if a reshape is underway.
Also (and more significantly) the raid5_conf_t values will be changed
at the same time (inside an appropriate lock) that the reshape is
started by setting reshape_position. In contrast, the new_chunk value
is set when the sysfs file is written which could be well before the
reshape starts.
Signed-off-by: NeilBrown <neilb@suse.de>
During a raid5 reshape, we have some stripes in the cache that are
'before' the reshape (and are still to be processed) and some that are
'after'. They are currently differentiated by having different
->disks values as the only reshape current supported involves changing
the number of disks.
However we will soon support reshapes that do not change the number
of disks (chunk parity or chunk size). So make the difference more
explicit with a 'generation' number.
Signed-off-by: NeilBrown <neilb@suse.de>
When reducing the number of devices in a raid4/5/6, the reshape
process has to start at the end of the array and work down to the
beginning. So we need to handle expand_progress and expand_lo
differently.
This patch renames "expand_progress" and "expand_lo" to avoid the
implication that anything is getting bigger (expand->reshape) and
every place they are used, we make sure that they are used the right
way depending on whether delta_disks is positive or negative.
Signed-off-by: NeilBrown <neilb@suse.de>
Move the raid6 data processing routines into a standalone module
(raid6_pq) to prepare them to be called from async_tx wrappers and other
non-md drivers/modules. This precludes a circular dependency of raid456
needing the async modules for data processing while those modules in
turn depend on raid456 for the base level synchronous raid6 routines.
To support this move:
1/ The exportable definitions in raid6.h move to include/linux/raid/pq.h
2/ The raid6_call, recovery calls, and table symbols are exported
3/ Extra #ifdef __KERNEL__ statements to enable the userspace raid6test to
compile
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
.. so that the code to create the private data structures is separate.
This will help with future code to change the level of an active
array.
Signed-off-by: NeilBrown <neilb@suse.de>
DDF requires RAID6 calculations over different devices in a different
order.
For md/raid6, we calculate over just the data devices, starting
immediately after the 'Q' block.
For ddf/raid6 we calculate over all devices, using zeros in place of
the P and Q blocks.
This requires unfortunately complex loops...
Signed-off-by: NeilBrown <neilb@suse.de>
DDF uses different layouts for P and Q blocks than current md/raid6
so add those that are missing.
Also add support for RAID6 layouts that are identical to various
raid5 layouts with the simple addition of one device to hold all of
the 'Q' blocks.
Finally add 'raid5' layouts to match raid4.
These last to will allow online level conversion.
Note that this does not provide correct support for DDF/raid6 yet
as the order in which data blocks are summed to produce the Q block
is significant and different between current md code and DDF
requirements.
Signed-off-by: NeilBrown <neilb@suse.de>
Code currently assumes that the devices in a raid6 stripe are
0 1 ... N-1 P Q
in some rotated order. We will shortly add new layouts in which
this strict pattern is broken.
So remove this expectation. We still assume that the data disks
are roughly in-order. However P and Q can be inserted anywhere within
that order.
Signed-off-by: NeilBrown <neilb@suse.de>
This makes the includes more explicit, and is preparation for moving
md_k.h to drivers/md/md.h
Remove include/raid/md.h as its only remaining use was to #include
other files.
Signed-off-by: NeilBrown <neilb@suse.de>
Move the headers with the local structures for the disciplines and
bitmap.h into drivers/md/ so that they are more easily grepable for
hacking and not far away. md.h is left where it is for now as there
are some uses from the outside.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown
Markus Stockhausen
shli@kernel.org
Linus Torvalds
Michael Opdenacker
Paul Bolle
majianpeng
Jens Axboe
Tejun Heo
Dan Williams
Andre Noll
Christoph Hellwig