Both of these drivers use ioport_map(), so they need to
depend on HAS_IOPORT_MAP. Otherwise, they cannot be built
even with COMPILE_TEST on architectures without an ioport
implementation, such as ARCH=um.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When userspace requests a GPIO v1 line info changed event,
lineinfo_watch_read() populates and returns the gpioline_info_changed
structure. It contains 5 words of padding at the end which are not
initialized before being returned to userspace.
Zero the structure in gpio_v2_line_info_change_to_v1() before populating
its contents.
Fixes: aad955842d ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Signed-off-by: Gabriel Knezek <gabeknez@linux.microsoft.com>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
A disabled/masked interrupt marked as wakeup source must be re-enable
and unmasked in order to be able to wake-up the host. That can be done
by flaging the irqchip with IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND.
Note: It 'sometimes' works without that change, but only thanks to the
lazy generic interrupt disabling (keeping interrupt unmasked).
Reported-by: Michal Koziel <michal.koziel@emlogic.no>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
bit-mask for pins 0 to 4 is BIT(0) to BIT(4) however we ended up with BIT(n - 1)
which is not right, and this was caught by below usban check
UBSAN: shift-out-of-bounds in drivers/gpio/gpio-wcd934x.c:34:14
Fixes: 59c3246834 ("gpio: wcd934x: Add support to wcd934x gpio controller")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When hotplugging CPUs on Tegra186 and Tegra194 errors such as the
following are seen ...
IRQ63: set affinity failed(-22).
IRQ65: set affinity failed(-22).
IRQ66: set affinity failed(-22).
IRQ67: set affinity failed(-22).
Looking at the /proc/interrupts the above are all interrupts associated
with GPIOs. The reason why these error messages occur is because there
is no 'parent_data' associated with any of the GPIO interrupts and so
tegra186_irq_set_affinity() simply returns -EINVAL.
To understand why there is no 'parent_data' it is first necessary to
understand that in addition to the GPIO interrupts being routed to the
interrupt controller (GIC), the interrupts for some GPIOs are also
routed to the Tegra Power Management Controller (PMC) to wake up the
system from low power states. In order to configure GPIO events as
wake events in the PMC, the PMC is configured as IRQ parent domain
for the GPIO IRQ domain. Originally the GIC was the IRQ parent domain
of the PMC and although this was working, this started causing issues
once commit 64a267e9a4 ("irqchip/gic: Configure SGIs as standard
interrupts") was added, because technically, the GIC is not a parent
of the PMC. Commit c351ab7bf2 ("soc/tegra: pmc: Don't create fake
interrupt hierarchy levels") fixed this by severing the IRQ domain
hierarchy for the Tegra GPIOs and hence, there may be no IRQ parent
domain for the GPIOs.
The GPIO controllers on Tegra186 and Tegra194 have either one or six
interrupt lines to the interrupt controller. For GPIO controllers with
six interrupts, the mapping of the GPIO interrupt to the controller
interrupt is configurable within the GPIO controller. Currently a
default mapping is used, however, it could be possible to use the
set affinity callback for the Tegra186 GPIO driver to do something a
bit more interesting. Currently, because interrupts for all GPIOs are
have the same mapping and any attempts to configure the affinity for
a given GPIO can conflict with another that shares the same IRQ, for
now it is simpler to just remove set affinity support and this avoids
the above warnings being seen.
Cc: <stable@vger.kernel.org>
Fixes: c4e1f7d92c ("gpio: tegra186: Set affinity callback to parent")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Kernel doc validator complains:
.../gpio-xilinx.c:556: warning: expecting prototype for xgpio_of_probe(). Prototype was for xgpio_probe() instead
Correct as suggested by changing the name of the function in the doc..
Fixes: 749564ffd5 ("gpio/xilinx: Convert the driver to platform device interface")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Neeli Srinivas <sneeli@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- new driver for the Realtek Otto GPIO controller
- ACPI support for gpio-mpc8xxx
- edge event support for gpio-sch (+ Kconfig fixes)
- Kconfig improvements in gpio-ich
- fixes to older issues in gpio-mockup
- ACPI quirk for ignoring EC wakeups on Dell Venue 10 Pro 5055
- improve the GPIO aggregator code by using more generic interfaces instead of
reimplementing them in the driver
- convert the DT bindings for gpio-74x164 to yaml
- documentation improvements
- a slew of other minor fixes and improvements to GPIO drivers
-----BEGIN PGP SIGNATURE-----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=5vLN
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.13-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
- new driver for the Realtek Otto GPIO controller
- ACPI support for gpio-mpc8xxx
- edge event support for gpio-sch (+ Kconfig fixes)
- Kconfig improvements in gpio-ich
- fixes to older issues in gpio-mockup
- ACPI quirk for ignoring EC wakeups on Dell Venue 10 Pro 5055
- improve the GPIO aggregator code by using more generic interfaces
instead of reimplementing them in the driver
- convert the DT bindings for gpio-74x164 to yaml
- documentation improvements
- a slew of other minor fixes and improvements to GPIO drivers
* tag 'gpio-updates-for-v5.13-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (34 commits)
dt-bindings: gpio: add YAML description for rockchip,gpio-bank
gpio: mxs: remove useless function
dt-bindings: gpio: fairchild,74hc595: Convert to json-schema
gpio: it87: remove unused code
gpio: 104-dio-48e: Fix coding style issues
gpio: mpc8xxx: Add ACPI support
gpio: ich: Switch to be dependent on LPC_ICH
gpio: sch: Drop MFD_CORE selection
gpio: sch: depends on LPC_SCH
gpiolib: acpi: Add quirk to ignore EC wakeups on Dell Venue 10 Pro 5055
gpio: sch: Hook into ACPI GPE handler to catch GPIO edge events
gpio: sch: Add edge event support
gpio: aggregator: Replace custom get_arg() with a generic next_arg()
lib/cmdline: Export next_arg() for being used in modules
gpio: omap: Use device_get_match_data() helper
gpio: Add Realtek Otto GPIO support
dt-bindings: gpio: Binding for Realtek Otto GPIO
docs: kernel-parameters: Add gpio_mockup_named_lines
docs: kernel-parameters: Move gpio-mockup for alphabetic order
lib: bitmap: provide devm_bitmap_alloc() and devm_bitmap_zalloc()
...
Fixed multiple bare uses of 'unsigned' without 'int'.
Fixed space around "*" operator.
Fixed function parameter alignment to opening parenthesis.
Reported by checkpatch.
Signed-off-by: Barney Goette <barneygoette@gmail.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Current implementation only supports DT, now add ACPI support.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Driver is neither dependent to PCI nor using MFD_CORE.
Replace those dependency and selection by dependency on LPC_ICH.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Since we are depended on LPC_SCH, which selects MFD_CORE,
we don't need to do it ourselves.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Since LPC_SCH provides GPIO functionality, GPIO_SCH should depend on
LPC_SCH to prevent kconfig warning and build errors:
WARNING: unmet direct dependencies detected for LPC_SCH
Depends on [n]: HAS_IOMEM [=y] && PCI [=n]
Selected by [y]:
- GPIO_SCH [=y] && GPIOLIB [=y] && X86 [=y] && (X86 [=y] || COMPILE_TEST [=n]) && ACPI [=y]
and
../drivers/mfd/lpc_sch.c:204:1: warning: data definition has no type or storage class
module_pci_driver(lpc_sch_driver);
^~~~~~~~~~~~~~~~~
../drivers/mfd/lpc_sch.c:204:1: error: type defaults to ‘int’ in declaration of ‘module_pci_driver’ [-Werror=implicit-int]
../drivers/mfd/lpc_sch.c:204:1: warning: parameter names (without types) in function declaration
../drivers/mfd/lpc_sch.c:197:26: warning: ‘lpc_sch_driver’ defined but not used [-Wunused-variable]
static struct pci_driver lpc_sch_driver = {
^~~~~~~~~~~~~~
Fixes: 6c46215d6b62 ("gpio: sch: Hook into ACPI GPE handler to catch GPIO edge events")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Like some other Bay and Cherry Trail SoC based devices the Dell Venue
10 Pro 5055 has an embedded-controller which uses ACPI GPIO events to
report events instead of using the standard ACPI EC interface for this.
The EC interrupt is only used to report battery-level changes and
it keeps doing this while the system is suspended, causing the system
to not stay suspended.
Add an ignore-wake quirk for the GPIO pin used by the EC to fix the
spurious wakeups from suspend.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Neither the ACPI description on Intel Minnowboard (v1) platform provides
the required information to establish a generic handling nor the hardware
capable of doing it. According to the data sheet the hardware can generate
SCI events. Therefore, we need to hook from the driver into GPE handler of
the ACPI subsystem in order to catch and report GPIO-related events.
Validated on the Inlel Minnowboard (v1) platform and Intel Galileo Gen 2.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add the required infrastructure to enable and report edge events
of the pins to the GPIO core. The actual hook-up of the event interrupt
will happen separately.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
cmdline library provides next_arg() helper to traverse over parameters
and their values given in command line. Replace custom approach in the driver
by it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use the device_get_match_data() helper instead of open coding.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Realtek MIPS SoCs (platform name Otto) have GPIO controllers with up to
64 GPIOs, divided over two banks. Each bank has a set of registers for
32 GPIOs, with support for edge-triggered interrupts.
Each GPIO bank consists of four 8-bit GPIO ports (ABCD and EFGH). Most
registers pack one bit per GPIO, except for the IMR register, which
packs two bits per GPIO (AB-CD).
Although the byte order is currently assumed to have port A..D at offset
0x0..0x3, this has been observed to be reversed on other, Lexra-based,
SoCs (e.g. RTL8196E/97D/97F).
Interrupt support is disabled for the fallback devicetree-compatible
'realtek,otto-gpio'. This allows for quick support of GPIO banks in
which the byte order would be unknown. In this case, the port ordering
in the IMR registers may not match the reversed order in the other
registers (DCBA, and BA-DC or DC-BA).
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Core changes:
- A semantic change to handle pinmux and pinconf in explicit order
while up until now we depended on the semantic order in the
device tree. The device tree is a functional programming
language and does not imply any order, so the right thing is
for the pin control core to provide these semantics.
- Add a new pinmux-select debugfs file which makes it possible to
go in and select functions for a pin manually (iteratively, at
the prompt) for debugging purposes.
- Fixes to gpio regmap handling for a new pin control driver
making use of regmap-gpio.
- Use octal permissions on debugfs files.
New drivers:
- A massive rewrite of the former custom pin control driver for
MIPS Broadcom devices to instead use the pin control subsystem.
New pin control drivers for BCM6345, BCM6328, BCM6358, BCM6362,
BCM6368, BCM63268 and BCM6318 SoC variants are implemented.
- Support for PM8350, PM8350B, PM8350C, PMK8350, PMR735A and
PMR735B in the Qualcomm PMIC GPIO driver. Also the two GPIOs
on PM8008 are supported.
- Support for the Rockchip RK3568/RK3566 pin controller.
- Support for Ingenic JZ4730, JZ4750, JZ4755, JZ4775 and
X2000.
- Support for Mediatek MTK8195.
- Add a new Xilinx ZynqMP pin control driver.
Driver improvements and non-urgent fixes:
- Modularization and improvements of the Rockchip drivers.
- Some new pins added to the description of new Renesas SoCs.
- Clarifications of the GPIO base calculation in the Intel driver.
- Fix the function names for the MPP54 and MPP55 pins in the Armada
CP110 pin controller.
- GPIO wakeup interrupt map for Qualcomm SC7280 and SM8350.
- Support for ACPI probing of the Qualcomm SC8180x.
- Fix interrupt clear status on rockchip
- Fix some missing pins on the Ingenic JZ4770, some semantic
fixes for the behaviour of the Ingenic pin controller.
Add DMIC pins for JZ4780, X1000, X1500 and X1830.
- A slew of janitorial like of_node_put() calls.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAmCL5sAACgkQQRCzN7AZ
XXNX5RAAtdPvDrPzzWdeqNLyodnJu/SyeA2xbmsvywrSvgpSx3FojFW9AXY/sr7w
RuhGGA5KhnrovwiabRKoZ0d0lC/JtKdx5g2o9ePFHDy+7BzFnVacBjL38UftSKy0
4QpDNJ3zock/XTUgJdaJEsbHhP/N4fOF/SbLpguYzGz7JpybNrZ+2M73yeQSL6uE
yuhn/AgFMLgWS47nSAH91Yt387+XCEfB75nftXyFSN9GpQ9i3VixWsG3Um/Stoma
aR7IIknvHdpCrOHH1IKohYcdlOkE7Wh2wHXSJVv26M49Ri5KSXu17lsUknebQ/oq
UeDYdd/2q/wFjxdEbG2tqinEYHs3e1RPmatVesgyibtYHGwjnSFo/G6UtG4948ii
1exwBi+0fw58YWLu/z4bhnNtZx6VsOev6mJ5GF7pyYzGIJy3r5J/9KCDzOJEoLom
YTVmgZRjzJuH/i0rPgyg3lSxlP/pdvdk1YUMlIYN1zWdPnRqj7/q+qaxPOkltqD+
20NFkvhQuuq+dLn4jtNK9xr2+vIKxIRPClT3D/lAihEPC5MUaFw/+y/V7c1hEJfS
d1dh5DwgHK7i55/lqLFaXeNNYsmY/SiFecoB8xyFnOJFsHlSHe/6NfjmRhOMUn6V
IX2GG4CBAzaheIWtN/ub/DcQ1vwA2n9hO5WX+Y3CXkIxXUFPmJY=
=QrEn
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"There is a lot going on!
Core changes:
- A semantic change to handle pinmux and pinconf in explicit order
while up until now we depended on the semantic order in the device
tree. The device tree is a functional programming language and does
not imply any order, so the right thing is for the pin control core
to provide these semantics.
- Add a new pinmux-select debugfs file which makes it possible to go
in and select functions for a pin manually (iteratively, at the
prompt) for debugging purposes.
- Fixes to gpio regmap handling for a new pin control driver making
use of regmap-gpio.
- Use octal permissions on debugfs files.
New drivers:
- A massive rewrite of the former custom pin control driver for MIPS
Broadcom devices to instead use the pin control subsystem. New pin
control drivers for BCM6345, BCM6328, BCM6358, BCM6362, BCM6368,
BCM63268 and BCM6318 SoC variants are implemented.
- Support for PM8350, PM8350B, PM8350C, PMK8350, PMR735A and PMR735B
in the Qualcomm PMIC GPIO driver. Also the two GPIOs on PM8008 are
supported.
- Support for the Rockchip RK3568/RK3566 pin controller.
- Support for Ingenic JZ4730, JZ4750, JZ4755, JZ4775 and X2000.
- Support for Mediatek MTK8195.
- Add a new Xilinx ZynqMP pin control driver.
Driver improvements and non-urgent fixes:
- Modularization and improvements of the Rockchip drivers.
- Some new pins added to the description of new Renesas SoCs.
- Clarifications of the GPIO base calculation in the Intel driver.
- Fix the function names for the MPP54 and MPP55 pins in the Armada
CP110 pin controller.
- GPIO wakeup interrupt map for Qualcomm SC7280 and SM8350.
- Support for ACPI probing of the Qualcomm SC8180x.
- Fix interrupt clear status on rockchip
- Fix some missing pins on the Ingenic JZ4770, some semantic fixes
for the behaviour of the Ingenic pin controller. Add DMIC pins for
JZ4780, X1000, X1500 and X1830.
- A slew of janitorial like of_node_put() calls"
* tag 'pinctrl-v5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: Add Xilinx ZynqMP pinctrl driver support
firmware: xilinx: Add pinctrl support
pinctrl: rockchip: do coding style for mux route struct
pinctrl: Add PIN_CONFIG_MODE_PWM to enum pin_config_param
pinctrl: Introduce MODE group in enum pin_config_param
pinctrl: Keep enum pin_config_param ordered by name
dt-bindings: pinctrl: Add binding for ZynqMP pinctrl driver
pinctrl: core: Fix kernel doc string for pin_get_name()
pinctrl: mediatek: use spin lock in mtk_rmw
pinctrl: add drive for I2C related pins on MT8195
pinctrl: add pinctrl driver on mt8195
dt-bindings: pinctrl: mt8195: add pinctrl file and binding document
pinctrl: Ingenic: Add pinctrl driver for X2000.
pinctrl: Ingenic: Add pinctrl driver for JZ4775.
pinctrl: Ingenic: Add pinctrl driver for JZ4755.
pinctrl: Ingenic: Add pinctrl driver for JZ4750.
pinctrl: Ingenic: Add pinctrl driver for JZ4730.
dt-bindings: pinctrl: Add bindings for new Ingenic SoCs.
pinctrl: Ingenic: Reformat the code.
pinctrl: Ingenic: Add DMIC pins support for Ingenic SoCs.
...
- Add support for Software Nodes to MFD Core
- Remove support for Device Properties from MFD Core
- Use standard APIs in MFD Core
- New Drivers
- Add support for ROHM BD9576MUF and BD9573MUF PMICs
- Add support for Netronix Embedded Controller, PWM and RTC
- Add support for Actions Semi ATC260x PMICs and OnKey
- New Device Support
- Add support for DG1 PCIe Graphics Card to Intel PMT
- Add support for ROHM BD71815 PMIC to ROHM BD71828
- Add support for Tolino Shine 2 HD to Netronix Embedded Controller
- Add support for AX10 BMC Secure Updates to Intel M10 BMC
- Removed Device Support
- Remove Arizona Extcon support from MFD
- Remove ST-E AB8500 Power Supply code from MFD
- Remove AB3100 altogether
- New Functionality
- Add support for SMBus and I2C modes to Dialog DA9063
- Switch to using Software Nodes in Intel (various)
- New/converted Device Tree bindings; rohm,bd71815-pmic, rohm,bd9576-pmic,
netronix,ntxec, actions,atc260x,
ricoh,rn5t618, qcom-pm8xxx
- Fix-ups
- Fix error handling/path; intel_pmt
- Simplify code; rohm-bd718x7, ab8500-core, intel-m10-bmc
- Trivial clean-ups (reordering, spelling); rohm-generic, rn5t618, max8997
- Use correct data-type; db8500-prcmu
- Remove superfluous code; lp87565, intel_quark_i2c_gpi, lpc_sch, twl
- Use generic APIs/defines; lm3533-core, intel_quark_i2c_gpio
- Regmap related fix-ups; intel-m10-bmc, sec-core
- Reorder resource freeing during remove; intel_quark_i2c_gpio
- Make table indexing more robust; intel_quark_i2c_gpio
- Fix reference imbalances; arizona-irq
- Staticify and (un)constify things; arizona-spi, stmpe, ene-kb3930,
intel-lpss-acpi, intel-lpss-pci,
atc260x-i2c, intel_quark_i2c_gpio
- Bug Fixes
- Fix incorrect (register) values; intel-m10-bmc
- Kconfig related fixes; ABX500_CORE
- Do not clear the Auto Reload Register; stm32-timers
-----BEGIN PGP SIGNATURE-----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=IJSL
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Add support for Software Nodes to MFD Core
- Remove support for Device Properties from MFD Core
- Use standard APIs in MFD Core
New Drivers:
- Add support for ROHM BD9576MUF and BD9573MUF PMICs
- Add support for Netronix Embedded Controller, PWM and RTC
- Add support for Actions Semi ATC260x PMICs and OnKey
New Device Support:
- Add support for DG1 PCIe Graphics Card to Intel PMT
- Add support for ROHM BD71815 PMIC to ROHM BD71828
- Add support for Tolino Shine 2 HD to Netronix Embedded Controller
- Add support for AX10 BMC Secure Updates to Intel M10 BMC
Removed Device Support:
- Remove Arizona Extcon support from MFD
- Remove ST-E AB8500 Power Supply code from MFD
- Remove AB3100 altogether
New Functionality:
- Add support for SMBus and I2C modes to Dialog DA9063
- Switch to using Software Nodes in Intel (various)
New/converted Device Tree bindings:
- rohm bd71815-pmic, rohm bd9576-pmic, netronix ntxec, actions
atc260x, ricoh rn5t618, qcom pm8xxx
- Fix-ups:
- Fix error handling/path; intel_pmt
- Simplify code; rohm-bd718x7, ab8500-core, intel-m10-bmc
- Trivial clean-ups (reordering, spelling); rohm-generic, rn5t618,
max8997
- Use correct data-type; db8500-prcmu
- Remove superfluous code; lp87565, intel_quark_i2c_gpi, lpc_sch, twl
- Use generic APIs/defines; lm3533-core, intel_quark_i2c_gpio
- Regmap related fix-ups; intel-m10-bmc, sec-core
- Reorder resource freeing during remove; intel_quark_i2c_gpio
- Make table indexing more robust; intel_quark_i2c_gpio
- Fix reference imbalances; arizona-irq
- Staticify and (un)constify things; arizona-spi, stmpe, ene-kb3930,
intel-lpss-acpi, intel-lpss-pci, atc260x-i2c, intel_quark_i2c_gpio
Bug Fixes:
- Fix incorrect (register) values; intel-m10-bmc
- Kconfig related fixes; ABX500_CORE
- Do not clear the Auto Reload Register; stm32-timers"
* tag 'mfd-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (84 commits)
mfd: intel-m10-bmc: Add support for MAX10 BMC Secure Updates
Revert "mfd: max8997: Add of_compatible to Extcon and Charger mfd_cell"
mfd: twl: Remove unused inline function twl4030charger_usb_en()
dt-bindings: mfd: Convert pm8xxx bindings to yaml
dt-bindings: mfd: Add compatible for pmk8350 rtc
i2c: designware: Get rid of legacy platform data
mfd: intel_quark_i2c_gpio: Convert I²C to use software nodes
mfd: lpc_sch: Partially revert "Add support for Intel Quark X1000"
mfd: arizona: Fix rumtime PM imbalance on error
mfd: max8997: Replace 8998 with 8997
mfd: core: Use acpi_find_child_device() for child devices lookup
mfd: intel_quark_i2c_gpio: Don't play dirty trick with const
mfd: intel_quark_i2c_gpio: Enable MSI interrupt
mfd: intel_quark_i2c_gpio: Reuse BAR definitions for MFD cell indexing
mfd: ntxec: Support for EC in Tolino Shine 2 HD
mfd: stm32-timers: Avoid clearing auto reload register
mfd: intel_quark_i2c_gpio: Replace I²C speeds with descriptive definitions
mfd: intel_quark_i2c_gpio: Remove unused struct device member
mfd: intel_quark_i2c_gpio: Unregister resources in reversed order
mfd: Kconfig: ABX500_CORE should depend on ARCH_U8500
...
Updates for SoC specific drivers include a few subsystems that
have their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance optimized
for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target module
has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to avoid
issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as we
now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and dra7
- omap-prm driver needs to enable autoidle retention support for omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of using
builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=iidq
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance
optimized for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target
module has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to
avoid issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as
we now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and
dra7
- omap-prm driver needs to enable autoidle retention support for
omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of
using builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP"
* tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
soc: aspeed: fix a ternary sign expansion bug
memory: mtk-smi: Add device-link between smi-larb and smi-common
memory: samsung: exynos5422-dmc: handle clk_set_parent() failure
memory: renesas-rpc-if: fix possible NULL pointer dereference of resource
clk: socfpga: fix iomem pointer cast on 64-bit
soc: aspeed: Adapt to new LPC device tree layout
pinctrl: aspeed-g5: Adapt to new LPC device tree layout
ipmi: kcs: aspeed: Adapt to new LPC DTS layout
ARM: dts: Remove LPC BMC and Host partitions
dt-bindings: aspeed-lpc: Remove LPC partitioning
soc: fsl: enable acpi support in RCPM driver
soc: qcom: mdt_loader: Detect truncated read of segments
soc: qcom: mdt_loader: Validate that p_filesz < p_memsz
soc: qcom: pdr: Fix error return code in pdr_register_listener
firmware: qcom_scm: Fix kernel-doc function names to match
firmware: qcom_scm: Suppress sysfs bind attributes
firmware: qcom_scm: Workaround lack of "is available" call on SC7180
firmware: qcom_scm: Reduce locking section for __get_convention()
firmware: qcom_scm: Make __qcom_scm_is_call_available() return bool
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
...
- save and restore the sysconfig register in gpio-omap
-----BEGIN PGP SIGNATURE-----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=zaJj
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
"Save and restore the sysconfig register in gpio-omap to fix a
power-management issue"
* tag 'gpio-fixes-for-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: omap: Save and restore sysconfig
As we are using cpu_pm to save and restore context, we must also save and
restore the GPIO sysconfig register. This is needed because we are not
calling PM runtime functions at all with cpu_pm.
We need to save the sysconfig on idle as it's value can get reconfigured by
PM runtime and can be different from the init time value. Device specific
flags like "ti,no-idle-on-init" can affect the init value.
Fixes: b764a5863f ("gpio: omap: Remove custom PM calls and use cpu_pm instead")
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- do not allow exporting GPIO lines which were marked invalid by the driver
-----BEGIN PGP SIGNATURE-----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=GnR0
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v5.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
"A single fix for an older problem with the sysfs interface: do not
allow exporting GPIO lines which were marked invalid by the driver"
* tag 'gpio-fixes-for-v5.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: sysfs: Obey valid_mask
-----BEGIN PGP SIGNATURE-----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=7O9a
-----END PGP SIGNATURE-----
mergetag object a908a71669
type commit
tag ib-mfd-extcon-v5.13
tagger Lee Jones <lee.jones@linaro.org> 1616067995 +0000
Immutable branch between MFD and Extcon due for the v5.13 merge window
-----BEGIN PGP SIGNATURE-----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=3CZN
-----END PGP SIGNATURE-----
mergetag object eac013a0b7
type commit
tag ib-mfd-input-v5.13-1
tagger Lee Jones <lee.jones@linaro.org> 1615374673 +0000
Immutable branch between MFD and Input due for the v5.13 merge window
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEdrbJNaO+IJqU8IdIUa+KL4f8d2EFAmBIqV8ACgkQUa+KL4f8
d2EmIw//fydErEBA/TsNSSMfAxK+WRY3xDFdTwK9NorfJiyPFMwsfIZ2Y0BdGHpa
cNz4EMqcfKgHzblbla5EOW64RDIIFQfDTiuCJTGaTB5LUlI56hnKEuiKlrtKlQMC
3ZSxY5+SY5OFwof4LFPCASyn0N3bH8Mdd1inyFAIphFrgHKez353B9N2RwePlpLq
7jWaGABQVo28cPpkLl3Slo064xadzS2+Sklwii8gOOvtAGMkLkvLpFEcGCNFRX7l
OBnw8QP3SCg14b7hrtSys2g7onpH3M5eDt5LwJVqOXEY5SCWJUoultF0msNuGVlq
XGxJATebx0iU3IByhgTFmzj3ymCWZ7I/EeXD1GI0Fn5EscK1AsrRimlQNcxq9Nm7
tb/mV3FZlkNi6FjOq/rQ90QgT20t74tGrU9qpXlbwpB2Z9jO3GCDTFLt0XQFEE/4
83nqIjhYfbpkNXfRTH6/FPtFWqpfw+U8/kNMNWSk9BNta+67++vBQzeFAYWC6hFK
m7LTzyDNb/EHstAYdXIDblEX4x1VLOilKMaltRqlQC9sUZ4ZpA4YxFJKX21mtGBX
0jrM2SLeBff+Xv4i/UdoiGBC2uWiBPWW0G94IkDwpCM272q5br8LxTuKIzWCv4w4
/4J8bXtVfmXl74lXw90ZnMwHApq95+yPDd2g8XTcdo+zctSqS6E=
=NF6J
-----END PGP SIGNATURE-----
mergetag object aa47ad3f85
type commit
tag ib-mfd-platform-x86-v5.13
tagger Lee Jones <lee.jones@linaro.org> 1615373744 +0000
Immutable branch between MFD and Platform/x86 due for the v5.13 merge window
-----BEGIN PGP SIGNATURE-----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=340a
-----END PGP SIGNATURE-----
mergetag object ee0975c308
type commit
tag ib-mfd-power-v5.13
tagger Lee Jones <lee.jones@linaro.org> 1616489771 +0000
Immutable branch between MFD and Power due for the v5.13 merge window
-----BEGIN PGP SIGNATURE-----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=+5eM
-----END PGP SIGNATURE-----
mergetag object edbda8f787
type commit
tag ib-mfd-pwm-rtc-v5.13-1
tagger Lee Jones <lee.jones@linaro.org> 1615374433 +0000
Immutable branch between MFD, PWM and RTC due for the v5.13 merge window
-----BEGIN PGP SIGNATURE-----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=DySP
-----END PGP SIGNATURE-----
Merge tags 'ib-mfd-clk-gpio-regulator-rtc-v5.13', 'ib-mfd-extcon-v5.13', 'ib-mfd-input-v5.13-1', 'ib-mfd-platform-x86-v5.13', 'ib-mfd-power-v5.13', 'ib-mfd-pwm-rtc-v5.13-1' and 'ib-regulator-list-ramp-helpers-v5.13' into ibs-for-mfd-merged
Immutable branch between MFD, Clock, GPIO, Regulator and RTC due for the v5.13 merge window
Immutable branch between MFD and Extcon due for the v5.13 merge window
Immutable branch between MFD and Input due for the v5.13 merge window
Immutable branch between MFD and Platform/x86 due for the v5.13 merge window
Immutable branch between MFD and Power due for the v5.13 merge window
Immutable branch between MFD, PWM and RTC due for the v5.13 merge window
Support GPO(s) found from ROHM BD71815 power management IC. The IC has two
GPO pins but only one is properly documented in the data-sheet. The driver
exposes by default only the documented GPO. The second GPO is connected to
E5 pin and is marked as GND in the data-sheet. Control for this
undocumented pin can be enabled using a special DT property.
This driver is derived from work by Peter Yang <yanglsh@embest-tech.com>
although not so much of the original is left.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change my e-mail address to kabel@kernel.org, and fix my name in
non-code parts (add diacritical mark).
Link: https://lkml.kernel.org/r/20210325171123.28093-2-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not allow exporting GPIOs which are set invalid
by the driver's valid mask.
Fixes: 726cb3ba49 ("gpiolib: Support 'gpio-reserved-ranges' property")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This is needed for properly registering GPIO regmap as a child of a regmap
pin controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20210324081923.20379-3-noltari@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since platform_device_unregister() is NULL-aware, we don't need to duplicate
this check. Remove it and fold the rest of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
It's quite spread code to initialize IRQ domain options.
Let's fold it into a simple oneliner.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When IRQ domain is created for an ACPI case, the name of it becomes unknown-%d
since for now it utilizes of_node member only and doesn't consider fwnode case.
Convert IRQ domain creation code to utilize fwnode instead.
Before/After the change on Intel Galileo Gen 2 with two GPIO (IRQ) controllers:
unknown-1 ==> \_SB.PCI0.GIP0.GPO
unknown-2 ==> \_SB.NIO3
Due to the nature of this change we may also deduplicate the WARN():s
because in either case (DT or ACPI) the fwnode will be set correctly
and %pfw is an equivalent to what the current code prints as a prefix.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In the ACPI case we may use the firmware node in the similar way
as it's done for OF case. We may use that fwnode for other purposes
in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The initial value of the OF node based on presence of parent, but
at the same time this operation somehow appeared separately from others
that handle the OF case. On the other hand there is no need to assign
dev->fwnode in the OF case if code properly retrieves fwnode, i.e.
via dev_fwnode() helper.
Amend gpiolib.c and gpiolib-of.c code in order to group OF operations.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
We have (historically) different approaches how we identify the type
of a given fwnode. Let's standardize them across the library code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Use devm_rpi_firmware_get() so as to make sure we release RPi's firmware
interface when unbinding the device.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In case when the properties are supplied in the secondary fwnode
(for example, built-in device properties) the fwnode pointer left
unassigned. This makes unable to retrieve them.
Assign fwnode to parent's if no primary one provided.
Fixes: 7cba1a4d5e ("gpiolib: generalize devprop_gpiochip_set_names() for device properties")
Fixes: 2afa97e9868f ("gpiolib: Read "gpio-line-names" from a firmware node")
Reported-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 4731210c09 ("gpiolib: Bind gpio_device to a driver to enable fw_devlink=on by default")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
On STM32MP1, the GPIO banks are subnodes of pin-controller@50002000,
see arch/arm/boot/dts/stm32mp151.dtsi. The driver for
pin-controller@50002000 is in drivers/pinctrl/stm32/pinctrl-stm32.c
and iterates over all of its DT subnodes when registering each GPIO
bank gpiochip. Each gpiochip has:
- gpio_chip.parent = dev,
where dev is the device node of the pin controller
- gpio_chip.of_node = np,
which is the OF node of the GPIO bank
Therefore, dev_fwnode(chip->parent) != of_fwnode_handle(chip.of_node),
i.e. pin-controller@50002000 != pin-controller@50002000/gpio@5000*000.
The original code behaved correctly, as it extracted the "gpio-line-names"
from of_fwnode_handle(chip.of_node) = pin-controller@50002000/gpio@5000*000.
To achieve the same behaviour, read property from the firmware node.
Fixes: 7cba1a4d5e ("gpiolib: generalize devprop_gpiochip_set_names() for device properties")
Reported-by: Marek Vasut <marex@denx.de>
Reported-by: Roman Guskov <rguskov@dh-electronics.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The commit 0ea683931a ("gpio: dwapb: Convert driver to using the
GPIO-lib-based IRQ-chip") indeliberately made a regression on how
IRQ line from GPIO I²C expander is handled. I.e. it reveals that
the quirk for Intel Galileo Gen 2 misses the part of setting IRQ type
which previously was predefined by gpio-dwapb driver. Now, we have to
reorganize the approach to call necessary parts, which can be done via
ACPI_GPIO_QUIRK_ABSOLUTE_NUMBER quirk.
Without this fix and with above mentioned change the kernel hangs
on the first IRQ event with:
gpio gpiochip3: Persistence not supported for GPIO 1
irq 32, desc: 62f8fb50, depth: 0, count: 0, unhandled: 0
->handle_irq(): 41c7b0ab, handle_bad_irq+0x0/0x40
->irq_data.chip(): e03f1e72, 0xc2539218
->action(): 0ecc7e6f
->action->handler(): 8a3db21e, irq_default_primary_handler+0x0/0x10
IRQ_NOPROBE set
unexpected IRQ trap at vector 20
Fixes: ba8c90c618 ("gpio: pca953x: Override IRQ for one of the expanders on Galileo Gen 2")
Depends-on: 0ea683931a ("gpio: dwapb: Convert driver to using the GPIO-lib-based IRQ-chip")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Currently only search by index is supported. However, in some cases
we might need to pass the quirks to the acpi_dev_gpio_irq_get().
For this, split out acpi_dev_gpio_irq_get_by() and replace
acpi_dev_gpio_irq_get() by calling above with NULL for name parameter.
Fixes: ba8c90c618 ("gpio: pca953x: Override IRQ for one of the expanders on Galileo Gen 2")
Depends-on: 0ea683931a ("gpio: dwapb: Convert driver to using the GPIO-lib-based IRQ-chip")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
On some systems the ACPI tables has wrong pin number and instead of
having a relative one it provides an absolute one in the global GPIO
number space.
Add ACPI_GPIO_QUIRK_ABSOLUTE_NUMBER quirk to cope with such cases.
Fixes: ba8c90c618 ("gpio: pca953x: Override IRQ for one of the expanders on Galileo Gen 2")
Depends-on: 0ea683931a ("gpio: dwapb: Convert driver to using the GPIO-lib-based IRQ-chip")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
fixed the following coccicheck:
./drivers/gpio/gpiolib-acpi.c:176:7-27: ERROR: Threaded IRQ with no
primary handler requested without IRQF_ONESHOT
Make sure threaded IRQs without a primary handler are always request
with IRQF_ONESHOT
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Make sure to hold the gpio_lock when removing the gpio device from the
gpio_devices list (when dropping the last reference) to avoid corrupting
the list when there are concurrent accesses.
Fixes: ff2b135922 ("gpio: make the gpiochip a real device")
Cc: stable@vger.kernel.org # 4.6
Reviewed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Fix a NULL-pointer deference when deregistering the gpio character
device that was introduced by the recent stub-driver hack. When the new
"driver" is unbound as part of deregistration, driver core clears the
driver-data pointer which is used to retrieve the struct gpio_device in
its release callback.
Fix this by using container_of() in the release callback as should have
been done all along.
Fixes: 4731210c09 ("gpiolib: Bind gpio_device to a driver to enable fw_devlink=on by default")
Cc: Saravana Kannan <saravanak@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: syzbot+d27b4c8adbbff70fbfde@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Here is the "big" driver core and debugfs update for 5.12-rc1
This set of driver core patches caused a bunch of problems in linux-next
for the past few weeks, when Saravana tried to set fw_devlink=on as the
default functionality. This caused a number of systems to stop booting,
and lots of bugs were fixed in this area for almost all of the reported
systems, but this option is not ready to be turned on just yet for the
default operation based on this testing, so I've reverted that change at
the very end so we don't have to worry about regressions in 5.12. We
will try to turn this on for 5.13 if testing goes better over the next
few months.
Other than the fixes caused by the fw_devlink testing in here, there's
not much more:
- debugfs fixes for invalid input into debugfs_lookup()
- kerneldoc cleanups
- warn message if platform drivers return an error on their
remove callback (a futile effort, but good to catch).
All of these have been in linux-next for a while now, and the
regressions have gone away with the revert of the fw_devlink change.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYDZhzA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylS2wCfU28FxDWNwcWhPFVfRT8Mb3OxZ50An1sR4lNR
t5Ie4aztMUjVJhI9bq6g
=3NSB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / debugfs update from Greg KH:
"Here is the "big" driver core and debugfs update for 5.12-rc1
This set of driver core patches caused a bunch of problems in
linux-next for the past few weeks, when Saravana tried to set
fw_devlink=on as the default functionality. This caused a number of
systems to stop booting, and lots of bugs were fixed in this area for
almost all of the reported systems, but this option is not ready to be
turned on just yet for the default operation based on this testing, so
I've reverted that change at the very end so we don't have to worry
about regressions in 5.12
We will try to turn this on for 5.13 if testing goes better over the
next few months.
Other than the fixes caused by the fw_devlink testing in here, there's
not much more:
- debugfs fixes for invalid input into debugfs_lookup()
- kerneldoc cleanups
- warn message if platform drivers return an error on their remove
callback (a futile effort, but good to catch).
All of these have been in linux-next for a while now, and the
regressions have gone away with the revert of the fw_devlink change"
* tag 'driver-core-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (35 commits)
Revert "driver core: Set fw_devlink=on by default"
of: property: fw_devlink: Ignore interrupts property for some configs
debugfs: do not attempt to create a new file before the filesystem is initalized
debugfs: be more robust at handling improper input in debugfs_lookup()
driver core: auxiliary bus: Fix calling stage for auxiliary bus init
of: irq: Fix the return value for of_irq_parse_one() stub
of: irq: make a stub for of_irq_parse_one()
clk: Mark fwnodes when their clock provider is added/removed
PM: domains: Mark fwnodes when their powerdomain is added/removed
irqdomain: Mark fwnodes when their irqdomain is added/removed
driver core: fw_devlink: Handle suppliers that don't use driver core
of: property: Add fw_devlink support for optional properties
driver core: Add fw_devlink.strict kernel param
of: property: Don't add links to absent suppliers
driver core: fw_devlink: Detect supplier devices that will never be added
driver core: platform: Emit a warning if a remove callback returned non-zero
of: property: Fix fw_devlink handling of interrupts/interrupts-extended
gpiolib: Don't probe gpio_device if it's not the primary device
device.h: Remove bogus "the" in kerneldoc
gpiolib: Bind gpio_device to a driver to enable fw_devlink=on by default
...
- new driver for the Toshiba Visconti platform
- rework of interrupt handling in gpio-tegra
- updates for GPIO selftests: we're now using the character device to perform
the subsystem checks
- support for a new rcar variant + some code refactoring
- refactoring of gpio-ep93xx
- SPDX License identifier has been updated in the uapi header so that userspace
programs bundling it can become fully REUSE-compliant
- improvements to pwm handling in gpio-mvebu
- support for interrupt handling and power management for gpio-xilinx as well
as some code refactoring
- support for a new chip variant in gpio-pca953x
- removal of drivers: zte xs & intel-mid and removal of leftovers from
intel-msic
- impovements to intel drivers pulled from Andy Shevchenko
- improvements to the gpio-aggregator virtual GPIO driver
- and several minor tweaks and fixes to code and documentation all over the
place
-----BEGIN PGP SIGNATURE-----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=OZtR
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"It's been a relatively calm release cycle and we're actually removing
more code than we're adding.
Summary:
- new driver for the Toshiba Visconti platform
- rework of interrupt handling in gpio-tegra
- updates for GPIO selftests: we're now using the character device to
perform the subsystem checks
- support for a new rcar variant + some code refactoring
- refactoring of gpio-ep93xx
- SPDX License identifier has been updated in the uapi header so that
userspace programs bundling it can become fully REUSE-compliant
- improvements to pwm handling in gpio-mvebu
- support for interrupt handling and power management for gpio-xilinx
as well as some code refactoring
- support for a new chip variant in gpio-pca953x
- removal of drivers: zte xs & intel-mid and removal of leftovers
from intel-msic
- impovements to intel drivers pulled from Andy Shevchenko
- improvements to the gpio-aggregator virtual GPIO driver
- and several minor tweaks and fixes to code and documentation all
over the place"
* tag 'gpio-updates-for-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (71 commits)
gpio: pcf857x: Fix missing first interrupt
gpio: ep93xx: refactor base IRQ number
gpio: ep93xx: refactor ep93xx_gpio_add_bank
gpio: ep93xx: Fix typo s/hierarchial/hierarchical
gpio: ep93xx: drop to_irq binding
gpio: ep93xx: Fix wrong irq numbers in port F
gpio: uapi: use the preferred SPDX license identifier
gpio: gpio-xilinx: Add check if width exceeds 32
gpio: gpio-xilinx: Add support for suspend and resume
gpio: gpio-xilinx: Add interrupt support
gpio: gpio-xilinx: Reduce spinlock array to array
gpio: gpio-xilinx: Simplify with dev_err_probe()
gpio: msic: Drop driver from Makefile
gpio: wcove: Split out to_ireg() helper and deduplicate the code
gpio: wcove: Switch to use regmap_set_bits(), regmap_clear_bits()
gpio: wcove: Get rid of error prone casting in IRQ handler
gpio: intel-mid: Remove driver for deprecated platform
gpio: msic: Remove driver for deprecated platform
gpio: aggregator: Remove trailing comma in terminator entries
gpio: aggregator: Use compound literal from the header
...