Граф коммитов

281 Коммитов

Автор SHA1 Сообщение Дата
Sudeep Holla 09bebb1adb power: vexpress: fix corruption in notifier registration
Vexpress platforms provide two different restart handlers: SYS_REBOOT
that restart the entire system, while DB_RESET only restarts the
daughter board containing the CPU. DB_RESET is overridden by SYS_REBOOT
if it exists.

notifier_chain_register used in register_restart_handler by design
relies on notifiers to be registered once only, however vexpress restart
notifier can get registered twice. When this happen it corrupts list
of notifiers, as result some notifiers can be not called on proper
event, traverse on list can be cycled forever, and second unregister
can access already freed memory.

So far, since this was the only restart handler in the system, no issue
was observed even if the same notifier was registered twice. However
commit 6c5c0d48b6 ("watchdog: sp805: add restart handler") added
support for SP805 restart handlers and since the system under test
contains two vexpress restart and two SP805 watchdog instances, it was
observed that during the boot traversing the restart handler list looped
forever as there's a cycle in that list resulting in boot hang.

This patch fixes the issues by ensuring that the notifier is installed
only once.

Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Fixes: 46c99ac662 ("power/reset: vexpress: Register with kernel restart handler")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-07-06 16:23:45 +02:00
Vinod Koul e6a578e289 power: reset: qcom-pon: Add Qcom PON driver
Add support Qualcomm PM8xxx PON which is responsible for reboot
mode support.

Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-07-06 15:53:58 +02:00
Alexey Khoroshilov f052df96c4 power: reset: zx-reboot: put device node in zx_reboot_probe()
zx_reboot_probe() increments refcnt of zx296702-pcu device node by
of_find_compatible_node() and leaves it undecremented on both
successful and error paths.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-06-28 14:20:38 +02:00
Mike Looijmans 77142a6112 gpio-poweroff: Use gpiod_set_value_cansleep
The power-off call is done in a context that must be able to sleep, so
use gpiod_set_value_cansleep instead of the atomic gpiod_set_value call.

This fixes a kernel warning at shutdown when the gpio is controlled
through an IO expander for example.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-04-25 23:05:59 +02:00
Ladislav Michl fd73a3e618 power: reset: at91-reset: Switch from the pr_*() to the dev_*() logging functions
Use dev_info() instead of pr_info().

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-03-19 20:51:17 +01:00
Ladislav Michl ab08824826 power: reset: at91-poweroff: Remove redundant dev_err call in at91_poweroff_probe()
There is an error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundancy.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-03-19 20:50:51 +01:00
Ladislav Michl 062836db01 power: reset: at91-poweroff: Switch from the pr_*() to the dev_*() logging functions
Use dev_info() instead of pr_info().

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-03-19 20:50:24 +01:00
Colin Ian King 93619fdec9 power: reset: make function sc27xx_poweroff_shutdown static
The function sc27xx_poweroff_shutdown is local to the source and does
not need to be in global scope, so make it static.

Cleans up sparse warning:
drivers/power/reset/sc27xx-poweroff.c:28:6: warning: symbol
'sc27xx_poweroff_shutdown' was not declared. Should it be static?

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-03-13 12:10:04 +01:00
Sebastian Reichel 75dd56c0cd Merge branch 'fixes' into for-next
Merge for-stable fixes branch into for-next development branch.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-03-12 14:35:10 +01:00
Moritz Fischer d85b4f7b7f power: reset: gpio-poweroff: Support for timeout from device property
Add support for reading a timeout value from device property.
Fall back to previous default of 3s if nothing is specified.

Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2018-03-09 17:15:03 +01:00
Baolin Wang 3f5faf3a06 power: reset: Add Spreadtrum SC27xx PMIC power off support
On Spreadtrum platform, we need power off system through external SC27xx
series PMICs including the SC2720, SC2721, SC2723, SC2730 and SC2731 chips.
Thus this patch adds SC27xx series PMICs power-off support.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-03-09 17:11:31 +01:00
Linus Walleij 4a9be94055 power: gemini-poweroff: Avoid spurious poweroff
On the D-Link DIR-685 we get spurious poweroff from
infrared. Since that block (CIR) doesn't even have a
driver this can be safely ignored, we can revisit this
code once we have a device supporting CIR.

On the D-Link DNS-313 we get spurious poweroff from
the power button. This appears to be an initialization
issue: we need to enable the block (start the state
machine) before we clear any dangling IRQ.

This patch fixes both issues.

Fixes: f7a388d6cd ("power: reset: Add a driver for the Gemini poweroff")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-02-22 21:35:04 +01:00
Alexandre Belloni 6ab739bc1d power: reset: Add a driver for the Microsemi Ocelot reset
The Microsemi Ocelot SoC has a register allowing to reset the MIPS core.
Unfortunately, the syscon-reboot driver can't be used directly (but almost)
as the reset control may be disabled using another register.

Cc: linux-pm@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-02-12 11:23:46 +01:00
Julia Lawall 8eb96f136f power: reset: account for const type of of_device_id.data
This driver creates a const structure that it stores in the data
field of an of_device_id array.

Add const to the declaration of the location that receives a value
from the data field to ensure that the compiler will continue to check
that the value is not modified and remove the const-dropping cast on
the access to the data field.

Done using Coccinelle.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-01-08 18:40:57 +01:00
Dong Aisheng baf61639b8 power: reset: remove unused imx-snvs-poweroff driver
There's no user of it in kernel now and it basically functions the same
as the generic syscon-poweroff.c to which we have already switched.
So let's remove it.

Cc: Robin Gong <yibin.gong@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-01-08 18:09:25 +01:00
Bjorn Andersson fd8b8f17d8 power: reset: msm: Clarify restart and poweroff
When PSHOLD in a Qualcomm platform is deasserted the PMIC will perform
either a power off or a restart of the system. The action to take is
configured in the PON block, which is controlled by a separate driver.

As the configuration logic was added to the pm8941-pwrkey driver the
comment in do_msm_poweroff() is no longer valid and the name
do_msm_restart() is misleading. Update the naming and drop the comment.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-01-08 18:04:43 +01:00
Jesse Chan 348c7cf5fc power: reset: zx-reboot: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
This change resolves a new compile-time warning
when built as a loadable module:

WARNING: modpost: missing MODULE_LICENSE() in drivers/power/reset/zx-reboot.o
see include/linux/module.h for more information

This adds the license as "GPL v2", which matches the header of the file.

MODULE_DESCRIPTION and MODULE_AUTHOR are also added.

Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2017-12-01 16:10:48 +01:00
Paul Burton fb615d61b5 Update MIPS email addresses
MIPS will soon not be a part of Imagination Technologies, and as such
many @imgtec.com email addresses will no longer be valid. This patch
updates the addresses for those who:

 - Have 10 or more patches in mainline authored using an @imgtec.com
   email address, or any patches dated within the past year.

 - Are still with Imagination but leaving as part of the MIPS business
   unit, as determined from an internal email address list.

 - Haven't already updated their email address (ie. JamesH) or expressed
   a desire to be excluded (ie. Maciej).

 - Acked v2 or earlier of this patch, which leaves Deng-Cheng, Matt &
   myself.

New addresses are of the form firstname.lastname@mips.com, and all
verified against an internal email address list.  An entry is added to
.mailmap for each person such that get_maintainer.pl will report the new
addresses rather than @imgtec.com addresses which will soon be dead.

Instances of the affected addresses throughout the tree are then
mechanically replaced with the new @mips.com address.

Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@mips.com>
Acked-by: Dengcheng Zhu <dengcheng.zhu@mips.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Acked-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-11-03 09:02:30 -07:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Rob Herring 2f04cd2a9b power: reset: Convert to using %pOF instead of full_name
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2017-07-24 14:09:31 +02:00
Sebastian Reichel 153e9e90ff Merge branch 'psy-reboot-mode-immutable' into psy-next 2017-06-08 18:21:25 +02:00
Bjorn Andersson f1bea8793d power: reset: reboot-mode: Make include file global
Move the reboot-mode.h include file into include/linux to allow drivers
outside drivers/power/reset to implement reboot-mode.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2017-06-08 18:18:19 +02:00
Florian Fainelli 1d2495e8c2 power: reset: Default POWER_RESET_BRCMSTB to BMIPS_GENERIC
On Broadcom MIPS STB platforms, BMIPS_GENERIC is the Kconfig symbol that
is used, make this reboot driver default to that value to make sure we
can reboot a system properly.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2017-06-08 13:05:30 +02:00
Florian Fainelli 12031fcae9 power: reset: Allow selecting POWER_RESET_BRCMSTB on ARM64
Since commit 37eb56dc79 ("arm64: Add Broadcom Set Top Box Kconfig
entry point") we have ARCH_BRCMSTB also visible on ARM64 platform, yet
this reboot driver was not selectable, so fix that.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2017-06-08 13:05:29 +02:00
Alexandre Belloni be04a0d77e power: reset: at91-sama5d2_shdwc: fix clobber list
Assembly in at91_lpddr_poweroff has r0 in the clobber list but uses r6.

Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2017-06-08 13:05:29 +02:00
Alexandre Belloni 2e9bbbf694 power: reset: at91-poweroff: fix clobber list
Assembly in at91_lpddr_poweroff has r0 in the clobber list but uses r6.

Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2017-06-08 13:05:28 +02:00
Linus Walleij f7a388d6cd power: reset: Add a driver for the Gemini poweroff
The Gemini (SL3516) SoC has a special power controller block
that only deal with shutting down the system.

If you do not register a driver and activate the block, the
power button on the systems utilizing this SoC will do an
uncontrolled power cut, which is why it is important to have
a special poweroff driver.

The most basic functionality is to just shut down the system
by writing a special bit in the control register after the
system has reached pm_poweroff.

It also handles the poweroff from a button or other sources:

When the poweroff button is pressed, or a signal is sent to
poweroff from an infrared remote control, or when the RTC
fires a special alarm (!) the system emits an interrupt.
At this point, Linux must acknowledge the interrupt and
proceed to do an orderly shutdown of the system.

After adding this driver, pressing the poweroff button gives
this dmesg:

root@gemini:/
root@gemini:/ gemini-poweroff 4b000000.power-controller:
poweroff button pressed

calling shutdown scripts..
setting /dev/rtc0 from system time
unmounting file systems...
umount: tmpfs busy - remounted read-only
umount: can't unmount /: Invalid argument
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system poweroff
uhci_hcd 0000:00:09.1: HCRESET not completed yet!
uhci_hcd 0000:00:09.0: HCRESET not completed yet!
reboot: Power down
gemini-poweroff 4b000000.power-controller: Gemini power off

Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2017-04-14 01:41:33 +02:00
Guy Shapiro f2c199db47 power: reset: syscon-poweroff: add a mask property
Make the syscon-poweroff driver accept value and mask instead of
just value.

Prior to this patch, the property name for the value was 'mask'. If
only the mask property is defined on a node, maintain compatibility
by using it as the value.

Signed-off-by: Guy Shapiro <guy.shapiro@mobi-wize.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2017-04-14 01:41:33 +02:00
Alexandre Belloni b6d30432e0 power: reset: at91-reset: remove leftover platform_device_id
commit eacd8d09db ("power/reset: at91-reset: remove useless
at91_reset_platform_probe()") removed non DT probe support but forgot to
remove the now useless id_table. Do that now.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2017-01-18 17:05:46 +01:00
Szemző András f22dfd86f0 power: reset: at91-reset: add samx7 support
Add samx7 support. It is lacking a few bits and needs a new reset function.

Signed-off-by: Szemző András <sza@esh.hu>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2017-01-18 17:05:38 +01:00
Alexandre Belloni 0b0408745e power: reset: at91-poweroff: timely shutdown LPDDR memories
LPDDR memories can only handle up to 400 uncontrolled power off. Ensure the
proper power off sequence is used before shutting down the platform.

Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2017-01-16 23:21:33 +01:00
Thomas Gleixner 8b0e195314 ktime: Cleanup ktime_set() usage
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
2016-12-25 17:21:22 +01:00
Javier Martinez Canillas 93f7c27b4d power: reset: zx-reboot: Fix module autoload
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/power/reset/zx-reboot.ko | grep alias
$

After this patch:

$ modinfo drivers/power/reset/zx-reboot.ko | grep alias
alias:          of:N*T*Czte,sysctrlC*
alias:          of:N*T*Czte,sysctrl

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-10-19 05:16:09 +02:00
Javier Martinez Canillas 0a27aa9c31 power: reset: syscon-reboot-mode: Fix module autoload
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/power/reset/syscon-reboot-mode.ko | grep alias
$

After this patch:

$ modinfo drivers/power/reset/syscon-reboot-mode.ko | grep alias
alias:          of:N*T*Csyscon-reboot-modeC*
alias:          of:N*T*Csyscon-reboot-mode

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-10-19 05:16:09 +02:00
Javier Martinez Canillas c9ba9b7763 power: reset: at91-poweroff: Fix module autoload
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/power/reset/at91-poweroff.ko | grep alias
$

After this patch:

$ modinfo drivers/power/reset/at91-poweroff.ko | grep alias
alias:          of:N*T*Catmel,at91sam9x5-shdwcC*
alias:          of:N*T*Catmel,at91sam9x5-shdwc
alias:          of:N*T*Catmel,at91sam9rl-shdwcC*
alias:          of:N*T*Catmel,at91sam9rl-shdwc
alias:          of:N*T*Catmel,at91sam9260-shdwcC*
alias:          of:N*T*Catmel,at91sam9260-shdwc

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-10-19 05:16:09 +02:00
Javier Martinez Canillas 991de44036 power: reset: at91-reset: Fix module autoload
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/power/reset/at91-reset.ko | grep alias
$

After this patch:

$ modinfo drivers/power/reset/at91-reset.ko | grep alias
alias:          of:N*T*Catmel,sama5d3-rstcC*
alias:          of:N*T*Catmel,sama5d3-rstc
alias:          of:N*T*Catmel,at91sam9g45-rstcC*
alias:          of:N*T*Catmel,at91sam9g45-rstc
alias:          of:N*T*Catmel,at91sam9260-rstcC*
alias:          of:N*T*Catmel,at91sam9260-rstc
alias:          platform:at91-sam9g45-reset
alias:          platform:at91-sam9260-reset

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-10-19 05:16:09 +02:00
Paul Burton 29676833df power: reset: Add Intel PIIX4 poweroff driver
Add a driver which allows powering off the system via an Intel PIIX4
southbridge, by entering the PIIX4 SOff state. This is useful on the
MIPS Malta development board, where it will power down the FPGA based
board until its ON/NMI button is pressed, or the QEMU implementation of
the MIPS Malta board where it will cause QEMU to exit.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-10-18 05:13:37 +02:00
Peter Griffin 8ad5d85efd power: reset: st-poweroff: Remove obsolete platforms.
This patch removes support for STiH415/6 SoC's from the
st-poweroff driver, as support for these platforms is
being removed from the kernel.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <linux-pm@vger.kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-09-19 21:32:22 +02:00
Arvind Yadav 7531be5cdf power: reset: zx-reboot: Unmap region obtained by of_iomap
Free memory mapping, if probe is not successful.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-09-19 21:25:41 +02:00
Arvind Yadav 896af83ef6 power: reset: xgene-reboot: Unmap region obtained by of_iomap
Free memory mapping, if probe is not successful.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-09-19 21:24:06 +02:00
Colin Ian King 1dff6ce026 power: reset: add in missing white space in error message text
A dev_err message spans two lines and the literal string is missing
a white space between words. Add the white space.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-09-19 21:19:46 +02:00
Sebastian Reichel f7c8f1de03 Power Supply Fixes for 4.8 cycle
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABCgAGBQJXsk2BAAoJENju1/PIO/qa0E4P/0rsS4Kzv+B61BJsoCIoXYOp
 p347gy6fS7QEJxSlHG430uVV74zlXQE3JTiBrjIdX2TKRA6EvD0RyM3/h+vfQU1c
 GviBJ53UwNlq1bBuJD1jkIHCvIW274FjX1h45Tytuzsi/8rLWas15oumnRFuOtyA
 UtgTbPtualYab01XgQyivv/dY4Dfb3d0aNPl3Nq77hAJMTVc9s1DLVqRMudqc0Zc
 e489mw+8l31L2pJs7CPxzNXqlS4YvMz4/mwbGCsqtEJTNHyzyrVH5VfCpMUNfGr4
 rZdqtF/nj/9c/DTIO6GvhoOVjja4MCEf3WpGCxrz2KUmhvxVTeBqsPStjE1xnC8u
 rNDDpRAwtjgpiw8fiEw+CXB5XsDMPmMSJi1KaOLz1q9O2GxHzoz2tgfjCh9V73qj
 J5pq1cQY2V6AkB+10WQ7afCnN3Zn2qDUoWXj2cvkd8yuvyfjTuC53Gd1sGpNk1dj
 f+euFLm6YYMvLv37vDCQDaxvzmud1Z60bgJy/uvbaVhcCABLUdbfwJpRf/3tWjp3
 rU3Lw43p5MPfBWHkZrzpQO33GEzO6FSrIkTr3YfVJiwAoViXgt5WEknbVde/pZDz
 Acn8UTE+6KeLrmrwA66pF++ewKjA7GgUzW50Ubju15rWujnwu5QVg/T+UVpGrB4k
 OYmwCtd5i2/OjnC+APnK
 =hK7R
 -----END PGP SIGNATURE-----

Merge tag 'for-v4.8-rc' into psy-next

Power Supply Fixes for 4.8 cycle
2016-08-16 01:17:42 +02:00
Bjorn Andersson 8dfdd2a842 power: reset: syscon-reboot-mode: Use managed resource API
Use the managed resource version of reboot_mode_register().

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-08-16 00:29:34 +02:00
Bjorn Andersson c1a9634f1a power: reset: reboot-mode: Add managed resource API
Provide managed resource version of reboot_mode_register() and
reboot_mode_unregister() to simplify implementations.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-08-16 00:29:22 +02:00
Arvind Yadav bae170efd6 power: reset: hisi-reboot: Unmap region obtained by of_iomap
Free memory mapping, if probe is not successful.

Fixes: 4a9b373718 ("power: reset: move hisilicon reboot code")
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-08-12 22:42:37 +02:00
Andy Yan 7a4947cf6f power: reset: reboot-mode: fix build error of missing ioremap/iounmap on UM
commit 4fcd504edb ("power: reset: add reboot mode driver") uses api from
syscon, and syscon uses ioremap/iounmap which depends on HAS_IOMEM, so
let's depend on MFD_SYSCON instead of selecting it directly to avoid the
um-allyesconfig like build error on archs that without iomem:

drivers/mfd/syscon.c: In function 'of_syscon_register':
drivers/mfd/syscon.c:67:9: error: implicit declaration of function 'ioremap' [-Werror=implicit-function-declaration]
  base = ioremap(res.start, resource_size(&res));
         ^
drivers/mfd/syscon.c:67:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
  base = ioremap(res.start, resource_size(&res));
       ^
drivers/mfd/syscon.c:109:2: error: implicit declaration of function 'iounmap' [-Werror=implicit-function-declaration]
  iounmap(base);
  ^

Reported-by: Kbuild test robot <fengguang.wu@intel.com>
Fixes: 4fcd504edbf7("power: reset: add reboot mode driver")
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-08-12 22:42:36 +02:00
Linus Torvalds 43a0a98aa8 ARM: SoC driver updates for v4.8
Driver updates for ARM SoCs.
 
 A slew of changes this release cycle. The reset driver tree, that we merge
 through arm-soc for historical reasons, is also sizable this time around.
 
 Among the changes:
 
  - clps711x: Treewide changes to compatible strings, merged here for simplicity.
  - Qualcomm: SCM firmware driver cleanups, move to platform driver
  - ux500: Major cleanups, removal of old mach-specific infrastructure.
  - Atmel external bus memory driver
  - Move of brcmstb platform to the rest of bcm
  - PMC driver updates for tegra, various fixes and improvements
  - Samsung platform driver updates to support 64-bit Exynos platforms
  - Reset controller cleanups moving to devm_reset_controller_register() APIs
  - Reset controller driver for Amlogic Meson
  - Reset controller driver for Hisilicon hi6220
  - ARM SCPI power domain support
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJXnm1XAAoJEIwa5zzehBx35lcP/ApuQarIXeZCQZtjlUBV9McW
 o3o7FhKFHePmEPeoYCvVeK5D8NykTkQv3WpnCknoxPJzxGJF7jbPWQJcVnXfKOXD
 kTcyIK15WL2HHtSE3lYyLfyUPz8AbJyRt0l0cxgcg6jvo+uzlWooNz1y78rLIYzg
 UwRssj7OiHv4dsyYRHZIsjnB8gMWw8rYMk154gP2xy6MnNXXzzOVVnOiVqxSZBm+
 EgIIcROMOqkkHuFlClMYKluIgrmgz1Ypjf+FuAg7dqXZd+TGRrmGXeI7SkGThfLu
 nyvY3N18NViNu7xOUkI9zg7+ifyYM8Si9ylalSICSJdIAxZfiwFqFaLJvVWKU1rY
 rBOBjKckQI0/X9WYusFNFHcijhIFV8/FgGAnVRRMPdvlCss7Zp03C9mR4AEhmKMX
 rLG49x81hU1C+LftC59ml3iB8dhZrrRkbxNHjLFHVGWNrKMrmJKa8JhXGRAoNM+u
 LRauiuJZatqvLfISNvpfcoW2EashVoU3f+uC8ymT3QCyME3wZm0t7T4tllxhMfBl
 sOgJqNkTKDmPLofwm/dASiLML7ZF1WePScrFyOACnj9K4mUD+OaCnowtWoQPu0eI
 aNmT84oosJ2S9F/iUDPtFHXdzQ+1QPPfSiQ9FXMoauciVq/2F+pqq68yYgqoxFOG
 vmkmG2YM4Wyq43u0BONR
 =O8+y
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver updates from Olof Johansson:
 "Driver updates for ARM SoCs.

  A slew of changes this release cycle.  The reset driver tree, that we
  merge through arm-soc for historical reasons, is also sizable this
  time around.

  Among the changes:

   - clps711x: Treewide changes to compatible strings, merged here for simplicity.
   - Qualcomm: SCM firmware driver cleanups, move to platform driver
   - ux500: Major cleanups, removal of old mach-specific infrastructure.
   - Atmel external bus memory driver
   - Move of brcmstb platform to the rest of bcm
   - PMC driver updates for tegra, various fixes and improvements
   - Samsung platform driver updates to support 64-bit Exynos platforms
   - Reset controller cleanups moving to devm_reset_controller_register() APIs
   - Reset controller driver for Amlogic Meson
   - Reset controller driver for Hisilicon hi6220
   - ARM SCPI power domain support"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
  ARM: ux500: consolidate base platform files
  ARM: ux500: move soc_id driver to drivers/soc
  ARM: ux500: call ux500_setup_id later
  ARM: ux500: consolidate soc_device code in id.c
  ARM: ux500: remove cpu_is_u* helpers
  ARM: ux500: use CLK_OF_DECLARE()
  ARM: ux500: move l2x0 init to .init_irq
  mfd: db8500 stop passing around platform data
  ASoC: ab8500-codec: remove platform data based probe
  ARM: ux500: move ab8500_regulator_plat_data into driver
  ARM: ux500: remove unused regulator data
  soc: raspberrypi-power: add CONFIG_OF dependency
  firmware: scpi: add CONFIG_OF dependency
  video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
  input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
  pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
  serial: clps711x: Changing the compatibility string to match with the smallest supported chip
  irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
  clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
  clk: clps711x: Changing the compatibility string to match with the smallest supported chip
  ...
2016-08-01 18:36:01 -04:00
Linus Torvalds 6f888fe31d ARM: SoC cleanups for v4.8
The cleanup branch keeps going down in size as we've completed a lot of
 the major legacy platform removals and conversions.
 
 A handful of changes this time around, some of the themes or larger sets are:
 
  - A bunch of i.MX cleanups around platform detection, init call cleanups
  - Misc fixes of missing/implicit includes
  - Removal of ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJXnnwFAAoJEIwa5zzehBx3zXQP/2a/+XkiseeGkEoiX/6FOfhH
 XTzipye0OYdEe3kVWFL1sVVXRH6a5sbDJRNtfsQc+KdSG5i7LMHWARRJmIx9CTMB
 oQ9pEbYKSyBQDHBSOZYT6W+qYOI2SdTYqesjd3yn+FY4SIFBpQ/V3axHnMICIRm9
 PmHF1QUQEdtQ2Y9+E1vA1mHcPN9enjlesD3VdRbxVPX/PZw63kx9y8ICVq5I/PX9
 DfJRcA+PKIYQghhEZ0cx2bEoKozv7W088C7DD1Umw1NN18pMuvvNQGhid80xUqKY
 4bmLSGWqwmSzv1WZ/u1pUnBGGQE9YY1U2b8kZy8hSVg9rupxS8Ang0ztZRRE6nk2
 4t8GmWuLDH+7PxFv/skzi1AMAx+4KxSfp3N5qyKr8ddmnYrFWmBPj2AeBqrlziw6
 8Z41LQULmf/Gs6McikGUP7ryqd15gNtTJO1wlavqFrPe0fyzcHsgqpIy3YCqZiSE
 wQ4Hc036xqGknmg6GjHWp+W1rHZVGsnXmvnp1IVRoAGqwBqxNi4ItIXE7an8144H
 NnWFmPRSsGg26MfEJVsbtPQWNtEGqM2lgr6zn9xirC0cVbQ4ZDtWp2q0bJ1v/cLQ
 sW6Gu6jgVN8YUPp56lBaXJ5RxHE9V1Sqi4/+KghBKWW0X/BIo99b6PVr2bJRrkaq
 ZvpvsgzbCHdGqTptF9Dw
 =SfR/
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC cleanups from Olof Johansson:
 "The cleanup branch keeps going down in size as we've completed a lot
  of the major legacy platform removals and conversions.

  A handful of changes this time around, some of the themes or larger
  sets are:

   - A bunch of i.MX cleanups around platform detection, init call cleanups
   - Misc fixes of missing/implicit includes
   - Removal of ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB"

* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
  ARM: mps2: fix typo
  ARM: s3c64xx: avoid warning about 'struct device_node'
  bus: mvebu-mbus: make mvebu_mbus_syscore_ops static
  bus: mvebu-mbus: fix __iomem on register pointers
  ARM: tegra: Remove board_init_funcs array
  ARM: iop: Fix indentation
  ARM: imx: remove cpu_is_mx*()
  ARM: imx: remove last call to cpu_is_mx5*
  ARM: imx: rework mx27_pm_init() call
  ARM: imx: deconstruct mx3_idle
  ARM: imx: deconstruct mxc_rnga initialization
  ARM: imx: remove cpu_is_mx1 check
  ARM: i.MX: Do not explicitly call l2x0_of_init()
  ARM: i.MX: system.c: Tweak prefetch settings for performance
  ARM: i.MX: system.c: Replace magic numbers
  ARM: i.MX: system.c: Remove redundant errata 752271 code
  ARM: i.MX: system.c: Convert goto to if statement
  ARM: Kirkwood: fix kirkwood_pm_init() declaration/type
  ARM: Kirkwood: make kirkwood_disable_mbus_error_propagation() static
  ARM: orion5x: make orion5x_legacy_handle_irq static
  ...
2016-08-01 18:21:13 -04:00
Andy Yan 4fcd504edb power: reset: add reboot mode driver
This driver parses the reboot commands like "reboot bootloader"
and "reboot recovery" to get a boot mode described in the
device tree , then call the write interfae to store the boot
mode in some place like special register or sram, which can
be read by the bootloader after system reboot, then the bootloader
can take different action according to the mode stored.

This is commonly used on Android based devices, in order to
reboot the device into fastboot or recovery mode.

Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-07-06 17:16:27 +02:00
Ben Dooks 0a14d280e1 power: vexpress: make dev_attr_active static
The dev_attr_active is not exported or defined to be used
outside the driver, so make it static to avoid the following
warning:

drivers/power/reset/vexpress-poweroff.c:77:1: warning: symbol 'dev_attr_active' was not declared. Should it be static?

Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
2016-06-13 09:55:51 +01:00
Ben Dooks d04b674e18 power/reset: make syscon_poweroff() static
The syscon_poweroff() function is not exported or declared for
usage elsewhere, so make it static to avoid the folloiwing warning:

drivers/power/reset/syscon-poweroff.c:33:6: warning: symbol 'syscon_poweroff' was not declared. Should it be static?

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-06-10 03:52:13 +02:00
Chris Brand 783cb948d7 power: Introduce Broadcom kona reset driver
This driver supports reset on both BCM21664 and BCM23550.
Code is being moved from arch/arm/mach-bcm/board_bcm21664.c

Signed-off-by: Chris Brand <chris.brand@broadcom.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2016-06-06 16:17:33 -07:00
Krzysztof Kozlowski e771e0a1e4 power: reset: keystone: Enable COMPILE_TEST
Enable the COMPILE_TEST to get build coverage, except on platforms
!HAS_IOMEM (required by selected MFD_SYSCON).

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-06-03 04:16:15 +02:00
Nicolas Ferre f80cb48843 power: reset: at91-shdwc: add new shutdown controller driver
Sama5d2 SoC has a completely new shutdown controller with new features and
register layout. It thus makes sense to add a new driver for this new
peripheral.

This driver is Device Tree only and handles events from the wake-up pin and
the RTC.
As the register layout may change in the future, so some values are encoded
in a configuration structure.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-04-10 17:17:38 +02:00
Richard Weinberger 4f4bfe6bf1 power: reset: Fix dependencies for !HAS_IOMEM archs
Not every arch has io memory.
So, unbreak the build by fixing the dependencies.

Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-02-15 06:06:07 +01:00
Linus Walleij 3f652c969d power/reset: versatile: support the actual versatile
While this driver is named after the Versatile family of
boards (ARM reference designs) the machine actually called
Versatile was not supported. This patch makes the driver
handle also that machine. We augment the register names for
the reset to *VERSATILE* as well since it is the same
register offsets for Versatile and RealView.

Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2016-02-15 05:45:22 +01:00
Julia Lawall c4c0edfbf8 power/reset: at91-reset: add missing of_node_put
for_each_matching_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.

A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):

// <smpl>
@@
expression e,e1;
local idexpression np;
@@

 for_each_matching_node(np, e1) {
   ... when != of_node_put(np)
       when != e = np
(
   return np;
|
+  of_node_put(np);
?  return ...;
)
   ...
 }
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-12-05 02:06:49 +01:00
Nicolas Ferre bc312cbdfa power: reset: at91-reset/trivial: driver applies to SAMA5 family as well
This diver doesn't applies only on SAM9 SoC families but on SAMA5 families
as well.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-09-22 15:45:39 +02:00
Alexandre Belloni 064380a12e power/reset: at91-poweroff: get and use slow clock
Commit dca1a4b5ff ("clk: at91: keep slow clk enabled to prevent system
hang") added a workaround for the slow clock as it is not properly handled
by its users.

Get and use the slow clock as it is necessary for the at91 shutdown
controller.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-09-22 15:18:53 +02:00
Alexandre Belloni 6dd1ad1f23 power/reset: at91-poweroff: allow compiling as a module
It was not possible to compile at91-poweroff as a module. Implement
.remove() to allow it. Also switch to module_platform_driver_probe() as it
is not hotpluggable.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-09-22 15:18:53 +02:00
Alexandre Belloni 2b2c6148fe power/reset: at91-reset: get and use slow clock
Commit dca1a4b5ff ("clk: at91: keep slow clk enabled to prevent system
hang") added a workaround for the slow clock as it is not properly handled
by its users.

Get and use the slow clock as it is necessary for the at91 reset
controller.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-09-22 15:18:52 +02:00
Alexandre Belloni 6e64180a7c power/reset: at91-reset: allow compiling as a module
It was not possible to compile at91-reset as a module. Implement .remove()
to allow it. Also switch to module_platform_driver_probe() as it is not
hotpluggable.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-09-22 15:18:52 +02:00
Alexandre Belloni eacd8d09db power/reset: at91-reset: remove useless at91_reset_platform_probe()
Since all the at91 platforms are now DT only, at91_reset_platform_probe()
is now useless, remove it.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-09-22 15:18:52 +02:00
Jun Nie 3309aa4941 power/reset: zx: Remove unnecessary include file
Including ARM related header file cause build failure
in i386 build because COMILE_TEST also involve building
zx driver. Remove the unnecessary include file.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-07-27 15:33:30 +02:00
Jun Nie dd9f1486ae power/reset: zx: Register restart handler
Register with kernel restart handler instead of setting arm_pm_restart
directly.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-07-24 17:29:17 +02:00
Josh Wu 1ae25d626c power: reset: at91: add sama5d3 reset function
This patch introduces a new compatible string: "atmel,sama5d3-rstc" and
new reset function for sama5d3 and later chips.

As in sama5d3 or later chips, we don't have to shutdown the DDR
controller before reset. Shutdown the DDR controller before reset is a
workaround to avoid DDR signal driving the bus, but since sama5d3 and
later chips there is no such a conflict.

So in this patch:
   1. the sama5d3 reset function only need to write the rstc register
and return.
   2. we can remove the code related with sama5d3 DDR controller as
we don't use it at all.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-07-20 18:12:09 +02:00
Linus Torvalds 75462c8a87 Replace module_platform_driver with builtin_platform driver in non modules.
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJVkO9lAAoJEOvOhAQsB9HWRV4P/jYrQm/S14ZfbwzqwV2w5xh+
 E1SHk+kjcLyIvG6JXknp8mlNFGFhsIZNhTq8wvYBmFHlkop9jlMqT3IwaV7y9baV
 NmxltPHVIgFhnPMBF6+nvMJVFe0oBXh3adwc02h/LcXauEPK98Na/BtAfX5nxmoy
 DO/9R+R3SxqShSHvQqM6JNu3M/xAxU7RRSMsthF3nZJfZEm5i7Sl9w6Zcmu67gEn
 KbAPmthHSzDvJZGPt6xQiR2OPvhdA2Ddxjey0/cLyl/IVd2DdUTUUHDY0lUpPd3A
 Ba6C6OaWoHbCoAVzGvXEJLP1CfuF5upTmo53FZ2+1fERzX7Co4E2xInq6qkpWK5+
 cLcqCZaxHXvmvmidrfTaJQ52dLseGAH5KsiDoR8m5RcsCMrK367V6ja5/A2UG+xW
 FVJzU7/1LRHzw17si/AcrD0Q3hFR0n6klEGS3E964fsyOuCYlSc77IspxZ7nF4QW
 cFKKweyAUdrmrlduS7rKxX4z/ne4ljbR1M82YxFVPWqg/n2cqQ4e9RQFeK8ogBe6
 ASXu6pmz03X5xoD7xPQEsVzjDDGPzGFdD/601j9cRJ0+TR9udECP776gXt+5Ml0L
 jWlhVGbt7BN64UFZ/kInGo1h6cS+JjlrBfNq6eZVQP78bZ5UWdyiupGzcLcixefN
 bnkl2MHHY/d6yk2Rs7zh
 =WLBw
 -----END PGP SIGNATURE-----

Merge tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux

Pull module_platform_driver replacement from Paul Gortmaker:
 "Replace module_platform_driver with builtin_platform driver in non
  modules.

  We see an increasing number of non-modular drivers using
  modular_driver() type register functions.  There are several downsides
  to letting this continue unchecked:

   - The code can appear modular to a reader of the code, and they won't
     know if the code really is modular without checking the Makefile
     and Kconfig to see if compilation is governed by a bool or
     tristate.

   - Coders of drivers may be tempted to code up an __exit function that
     is never used, just in order to satisfy the required three args of
     the modular registration function.

   - Non-modular code ends up including the <module.h> which increases
     CPP overhead that they don't need.

   - It hinders us from performing better separation of the module init
     code and the generic init code.

  So here we introduce similar macros for builtin drivers.  Then we
  convert builtin drivers (controlled by a bool Kconfig) by making the
  following type of mapping:

    module_platform_driver()       --->  builtin_platform_driver()
    module_platform_driver_probe() --->  builtin_platform_driver_probe().

  The set of drivers that are converted here are just the ones that
  showed up as relying on an implicit include of <module.h> during a
  pending header cleanup.  So we convert them here vs adding an include
  of <module.h> to non-modular code to avoid compile fails.  Additonal
  conversions can be done asynchronously at any time.

  Once again, an unused module_exit function that is removed here
  appears in the diffstat as an outlier wrt all the other changes"

* tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
  drivers/clk: convert sunxi/clk-mod0.c to use builtin_platform_driver
  drivers/power: Convert non-modular syscon-reboot to use builtin_platform_driver
  drivers/soc: Convert non-modular soc-realview to use builtin_platform_driver
  drivers/soc: Convert non-modular tegra/pmc to use builtin_platform_driver
  drivers/cpufreq: Convert non-modular s5pv210-cpufreq.c to use builtin_platform_driver
  drivers/cpuidle: Convert non-modular drivers to use builtin_platform_driver
  drivers/platform: Convert non-modular pdev_bus to use builtin_platform_driver
  platform_device: better support builtin boilerplate avoidance
2015-07-02 10:42:13 -07:00
Linus Torvalds 36a1624d88 power supply and reset changes for the v4.2 series
* New charger drivers: BQ24257, BQ25890, AXP288, RT9455
  * MAX17042 battery: add health & temperature support
  * BQ2415x charger: add ACPI support
  * misc. fixes and cleanups
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABCgAGBQJViI++AAoJENju1/PIO/qasPYP/0YMZdNNEUA/z1Uv8litaGbe
 gCzLRKuevt/996eVQcGJwsla/7AZwNgpUJya28mpiRqp+RbsTB4bkiGCkD2aO2Jw
 p34h9tIugU5H8+iL1+vl/ztpjwwm/bxEQHNpHK/YwqQLP7QazI6/yyRAUzYu0bGk
 RUndaStY/UZ/9KtSfGYF54kpxCXVQS0aHPMXXKQREr3Hg/VMlBoKQeAvJ7jTTjST
 7s9ZncO70jeY1NrSSdRY+anbuUNYqt0ndbaHhlpayGxnWL+PGdd2mNKq/ycGmBld
 8PwnDs+6fLv24PGYnkwbTryCbdvU9ZYUuNVb4XNTY+8x8CSPNuM8yYhqkmmq1dfI
 zXy1U9TCkLtKSk+7rxKWZc0WuWn2D9UJvr1zAoK9TMafdLi3YIMbm1TemKpLX/HJ
 chORnioPNgBiLmSzJ+nizWfWU5BQ5MhJamzhER0dRG9u8/2YJzCyNfd2miGrvAdL
 LecLcWopEDa+cAg5HM3usKcv0GsBJIes/jmtSMv2URWk8FHcXsDMsnl+D/77/LmV
 PM+HNJ/cNi7WGMgMO6lb1gULaRdAb6tZS865p2Abx5NkNjjRQw9A8EIwP30SPWh7
 aPhU6jxDdmhpez4nJeyHdjcQqnlE+Cxz9vwj8IMgneTjSl4guUY1HcgmAHJtrKGC
 WNB/r32UzJ5AZ0VxBB15
 =192M
 -----END PGP SIGNATURE-----

Merge tag 'for-4.2' of git://git.infradead.org/battery-2.6

Pull power supply and reset updates from Sebastian Reichel:

 - new charger drivers: BQ24257, BQ25890, AXP288, RT9455

 - MAX17042 battery: add health & temperature support

 - BQ2415x charger: add ACPI support

 - misc fixes and cleanups

* tag 'for-4.2' of git://git.infradead.org/battery-2.6: (32 commits)
  power_supply: Correct kerneldoc copy paste errors
  wm831x_power: Fix off-by-one at free_irq()
  power_supply: rt9455_charger: Fix error reported by static analysis tool
  power_supply: bq24257: use flags argument of devm_gpiod_get
  power_supply: bq25890: use flags argument of devm_gpiod_get
  sbs-battery: add option to always register battery
  power: Add devm_power_supply_get_by_phandle() helper function
  power_supply: max17042: Add OF support for setting thresholds
  power_supply: sysfs: Bring back write to writeable properties
  power_supply: rt9455_charger: Check if CONFIG_USB_PHY is enabled
  power: reset: gpio-restart: increase priority slightly
  power_supply: bq25890: make chip_id int
  power_supply: Add support for Richtek RT9455 battery charger
  Documentation: devicetree: Add Richtek RT9455 bindings
  of: Add vendor prefix for Richtek Technology Corporation
  power_supply: 88pm860x_charger: Do not call free_irq() twice
  power: bq24190_charger: Change first_time flag reset condition
  power: axp288_charger: axp288 charger driver
  power: max17042_battery: add HEALTH and TEMP_* properties support
  power_supply: Add support for TI BQ25890 charger chip
  ...
2015-06-23 16:10:27 -07:00
Paul Gortmaker e35415e59f drivers/power: Convert non-modular syscon-reboot to use builtin_platform_driver
This file depends on Kconfig options all of which are a bool, so
we use the appropriate registration function, which avoids us
relying on an implicit inclusion of <module.h> which we are
doing currently.

While this currently works, we really don't want to be including
the module.h header in non-modular code, which we'd be forced
to do, pending some upcoming code relocation from init.h into
module.h.  So we fix it now by using the non-modular equivalent.

Cc: Sebastian Reichel <sre@kernel.org>
Acked-By: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2015-06-16 14:12:38 -04:00
Heiko Stübner bcd56fe1aa power: reset: gpio-restart: increase priority slightly
gpio-restart uses a priority of 128 and currently most soc-level restart
mechanisms use the same - with some exceptions even using 192.
But while the soc-level restarts are provided by the soc itself,
gpio-restarts will most of the time be board-specfic and be used
when some special board condition makes the soc-level restart
only a second choice.

The problem at hand manifested itself on the rk3288-veyron devices.
While the soc-level restart can sucessfully restart all other rockchip
boards I have, the veyron devices use an external restart mechanism that
seems to not only reset the soc but also some external needed components.

With both restart handlers having priority 128 in my tests the soc-specific
variant took precedent in all cases. While it could restart the soc
sucessfully in all cases, firmware then got an issue when talking to an
external component, resulting in the device being put into recovery mode.

So, give the board-specific restart handler a slight push and move it
to priority 129 to make it more important than the generic soc-specific
restart-handler.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-06-02 20:59:03 +02:00
Uwe Kleine-König 9f6cd98fc3 power: reset: ltc2952: use _optional variant of devm_gpiod_get
devm_gpiod_get_optional returns NULL if devm_gpiod_get would return an
ENOENT error pointer.

There is no semantic change intended.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-05-23 20:03:42 +02:00
Uwe Kleine-König a34c0a8bf8 power: reset: gpio-poweroff: let devm_gpiod_get set direction of gpio
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-05-23 20:03:30 +02:00
Krzysztof Kozlowski 3236672092 power: at91-reset: Constify platform_device_id
The platform_device_id is not modified by the driver and core uses it as
const.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-05-23 19:44:23 +02:00
Thomas Gleixner c3b5d3cea5 Merge branch 'linus' into timers/core
Make sure the upstream fixes are applied before adding further
modifications.
2015-05-19 16:12:32 +02:00
Florian Fainelli 0a73125d30 power: reset: Add MFD_SYSCON depends for brcmstb
The Broadcom STB reboot driver depends on MFD_SYSCON, it uses
syscon_regmap_lookup_by_phandle() which will not lookup syscon phandles
if MFD_SYSCON is disabled, and instead will return -ENOSYS since it is
turned into an inline stub.

Fixes: 030494e750 ("power: reset: Add reboot driver for brcmstb")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-05-01 22:48:28 +02:00
Thomas Gleixner d8818257d3 power: reset: ltc2952: Remove bogus hrtimer_start() return value checks
The return value of hrtimer_start() tells whether the timer was
inactive or active already when hrtimer_start() was called.

The code emits a bogus warning if the timer was active already
claiming that the timer could not be started.

Remove it.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Frans Klaver <frans.klaver@xsens.com>
Cc: "René Moll" <linux@r-moll.nl>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-pm@vger.kernel.org
Acked-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-04-30 17:47:17 +02:00
Wei Yongjun 932df43005 power/reset: at91: fix return value check in at91_reset_platform_probe()
In case of error, the function devm_ioremap() returns NULL
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.

Fixes: ecfe64d8c5 ("power: reset: Add AT91 reset driver")
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-04-30 17:33:52 +02:00
Thomas Gleixner 4101ecc23d power: reset: ltc2952: Remove bogus hrtimer_start() return value checks
The return value of hrtimer_start() tells whether the timer was
inactive or active already when hrtimer_start() was called.

The code emits a bogus warning if the timer was active already
claiming that the timer could not be started.

Remove it along with the bogus comment in the else path.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Frans Klaver <frans.klaver@xsens.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-pm@vger.kernel.org
2015-04-23 14:38:01 +02:00
Moritz Fischer 8a577608ba power: reset: Add generic SYSCON register mapped poweroff.
Add a generic SYSCON register mapped poweroff mechanism.

Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-04-06 18:49:48 +02:00
Ben Dooks 7be5ac2c32 power/reset: at91: big endian fixes for atsama5d3x
Fix the passing of big endian data to routines that will be writing
it to the bus in the wrong order.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-03-26 15:21:00 +01:00
Fabian Frederick 8fb0885504 power: constify of_device_id array
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)

Signed-off-by: Fabian Frederick <fabf@skynet.be>

[for vexpress]
Acked-by: Sudeep Holla <sudeep.holla@arm.com>

Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-03-20 13:23:06 +01:00
Richard Weinberger 039ab50bda power/reset/rmobile-reset.c: Fix !HAS_IOMEM build
Fixes:
drivers/power/reset/rmobile-reset.c: In function ‘rmobile_reset_probe’:
drivers/power/reset/rmobile-reset.c:61:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
  iounmap(sysc_base2);

Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-03-20 13:06:01 +01:00
Guenter Roeck 7bae8f0481 power/reset: restart-poweroff: Remove arm dependencies
This driver is now arm specific anymore, so there is no need to include
an arm specific include file. Also drop unnecessary depencency on ARM
from Kconfig.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-25 22:13:18 +01:00
Guenter Roeck 7fa650bc0d power/reset: st-poweroff: Fix misleading Kconfig description
The st-poweroff driver does not really power off the system
but resets it, so Kconfig should not claim that the driver
would handle power-off.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-25 22:13:17 +01:00
Guenter Roeck 453fe4f11c power/reset: st-poweroff: Register with kernel restart handler
Register with kernel restart handler instead of setting arm_pm_restart
directly. Select high priority since the restart handler is instantiated
through devicetree, indicating that it should be used if configured.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-25 22:13:16 +01:00
Guenter Roeck b2b3a8b934 power/reset: Remove sun6i reboot driver
sun6i restart is now handled by its watchdog driver directly,
so this driver is no longer needed.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-25 22:13:07 +01:00
Guenter Roeck 481ff6ff96 power/reset: at91: Register with kernel restart handler
Register with kernel restart handler instead of setting arm_pm_restart
directly. Register with high priority since the driver unconditionally
overwrites other restart handlers if instantiated.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-25 22:12:45 +01:00
Guenter Roeck 25a5b57dd7 power/reset: arm-versatile: Register with kernel restart handler
Register with kernel restart handler instead of setting arm_pm_restart
directly. Select high priority since the restart handler is instantiated
through devicetree, indicating that it should be used if configured.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-25 22:12:45 +01:00
Kevin Cernekee 79969f6aaf power/reset: brcmstb: Add support for old 65nm chips
The register bit fields are a little different, so add an entry and a
compatible string to accommodate them.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-22 02:25:32 +01:00
Kevin Cernekee bb1de7f61f power/reset: brcmstb: Use the DT "compatible" string to indicate bit positions
Some of the older chips used different bits to arm and trigger the reset.
Add the infrastructure needed to specify this through the "compatible"
string.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-22 02:25:32 +01:00
Kevin Cernekee 4f5fd64046 power/reset: brcmstb: Make the driver buildable on MIPS
Now that the driver doesn't use any ARM-specific headers, it is safe
to build on MIPS or with COMPILE_TEST.

Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-22 02:25:31 +01:00
Guenter Roeck a538cf04ef power/reset: at91-poweroff: Fix error handling and other compiler warnings
at91_poweroff_get_wakeup_mode can return a negative error code and should
therefore not return an enum type. Similar, its result should not be
assigned to an enum type. Otherwise, the returned value is never negative,
resulting in a compiler warning and a missed error condition, which in turn
results in writing bad values into a chip register.

Also fix other compiler warnings which can be easily avoided.

drivers/power/reset/at91-poweroff.c:74:24:
	warning: type qualifiers ignored on function return type
drivers/power/reset/at91-poweroff.c:74:24:
	warning: no previous prototype for 'at91_poweroff_get_wakeup_mode'
drivers/power/reset/at91-poweroff.c:83:16:
	warning: comparison between signed and unsigned integer expressions
drivers/power/reset/at91-poweroff.c:97:2:
	warning: comparison of unsigned expression < 0 is always false

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-21 20:06:44 +01:00
Geert Uytterhoeven fa0f8d6700 power: reset: Add reset driver for R-Mobile platforms
Add a reset driver for Renesas R-Mobile and SH-Mobile SoCs. It registers
a restart handler to trigger a soft power-on reset through the R-Mobile
System Controller.
The priority of this restart handler is 192, to allow a watchdog driver
to use priority 128.

Note that we do not use syscon-reboot, as the HPB (Peripheral Bus
Bridge) semaphore should be acquired on systems where both the ARM and
SH core are in use. The driver can be extended later to support this,
when needed.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-21 16:32:05 +01:00
Pawel Moll 8f961c0a53 power/reset: vexpress: Remove non-DT code
Now, as all VE platforms have to be booted with DT,
the code handling non-DT case can be removed.

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-21 03:19:54 +01:00
Frans Klaver ee18185331 power: reset: ltc2952: make trigger input optional
Currently the ltc2952 supports only one button sequence to initiate
powerdown. This is not always desirable, as even prolonged button
presses can happen in use.

Allow ltc2952 users to pick their own power down sequence, by making the
trigger input optional. Since this still means that the ltc2952 may
power down the platform if the power button is pressed for about 5
seconds, we still need to make sure to start the watchdog toggle to
prolong the system power for as long as we need it.

This will still allow the system to control power using the kill signal.

Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-20 13:58:31 +01:00
Frans Klaver c1ada2ff80 power: reset: ltc2952: check trigger value before starting timer
In ltc2952_poweroff_handler it is theoretically possible that the timer
fails to start on first pass (button press), but succeeds in starting on
the second (button release). This will cause the button press to be
misinterpreted, and will incorrectly shut down the system. Because a
picture says more than a thousand words:

Expected behavior:
tmr:      ++++++++++
btn: -----__________-----

Faulty behavior:
tmr:                +++++
btn: -----__________-----

Legend:
+ timer runs
_ button pressed
- button depressed

To prevent this from happening, check the value of the gpio before
starting the timer. If the button is active, we should start the timer,
else we should stop it.

The situation described can now still occur if the polarity of the input
pin is set incorrectly, but that at least is predictable behavior and
can be detected during the first tests.

Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-20 13:58:30 +01:00
Frans Klaver 2f6ea8ad73 power: reset: ltc2952: disable timers in _remove
Disable the timers when ltc2952_poweroff is removed. We don't want to
risk calling functions on data that no longer exist.

Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-20 13:58:30 +01:00
Frans Klaver 5689b786f7 power: reset: ltc2952: fix C++ style function pointers
The function pointers for the timers and pm_power_off are assigned with
C++ style
	foo = &func;

Let's change it instead to the more C style
	foo = func;

Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-20 13:58:30 +01:00
Frans Klaver 5c3faad29b power: reset: ltc2952: cleanup control flow in poweroff_handler
ltc2952_poweroff_handler uses gotos to return from the function. Since
we don't do cleanups exiting this function, just return IRQ_HANDLED on
the spot and be done with it.

While at it, remove the variable 'ret'. It was never used very much.

Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-20 13:58:30 +01:00
Frans Klaver 0428c40d4c power: reset: ltc2952: drop empty suspend/resume functions
Documentation/SubmittingDrivers suggests these be implemented even when
they do nothing. On the other hand, the platform code calls these
functions 'legacy'. Suspend and resume operations should go into a
pm_ops structure, pointed at by the driver's pm field. This approach
would lead to a lot of boiler plate, while achieving nothing. Drop the
functions instead.

Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-20 13:58:29 +01:00
Frans Klaver 818ca4c8c7 power: reset: ltc2952: remove global variable poweroff_panic
As per Documentation/CodingStyle ch.4, we should keep global variables
to a mininum. Move the panic state into the driver data, regardless of
whether panic is a system state or not.

This removes the need for the custom _init and _exit functions, so
replace them with a call to the module_platform_driver() macro.

Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-20 13:58:28 +01:00
Frans Klaver a5f67be520 power: reset: ltc2952: reduce dependency on global variables
Documentation/CodingStyle ch.4 mentions in a side node that global
variables should only be used if you really need them. Reduce the use of
the global instance of ltc2952_poweroff so we may eventually remove it
entirely.

While at it, rename ltc2952_poweroff_data to ltc2952_poweroff, just to
save that little bit of typing.

Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-20 13:58:28 +01:00
Frans Klaver 62113b3117 power: reset: ltc2952: prefer devm_gpiod_get over gpiod_get
This reduces cleanup code and chance of errors.

Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-20 13:58:28 +01:00
Frans Klaver f66472df69 power: reset: ltc2952: unroll gpio_desc array
The three gpio's used by this driver are stored in an array of pointers.
This doesn't add much besides cleanups in a loop. In fact, it makes most
of the usage sites harder to read. Unroll the loop, and live with the
fact that cleanups become slightly larger.

Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-20 13:58:28 +01:00
Frans Klaver 07d08237d3 power: reset: ltc2952: prefer devm_request_irq over request_irq
Make use of the fact that we allocated resources can be automatically
deallocated. This reduces cleanup code and chance of errors. It also
removes the need for the virq member of the ltc2952_poweroff_data
struct.

Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-20 13:58:28 +01:00
Frans Klaver 0a5c6a2276 power: reset: ltc2952: prefer devm_kzalloc over kzalloc
Make use of the fact that the allocated resources can be automatically
deallocated. This reduces cleanup code and chance of leaks.

Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-20 13:58:27 +01:00
Linus Walleij 0160817d10 power: reset: augment versatile driver for integrator
Augment the Versatile reset driver to also handle the core
module reset sequence used on the Integrator/AP and
Integrator/CP.

Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2015-01-20 13:58:27 +01:00
Linus Torvalds 7051d8e630 power supply and reset changes for the v3.19 series
* update power/reset drivers to use kernel restart handler
 * add power off driver for i.mx6
 * add DT support for gpio-charger
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABCgAGBQJUjv52AAoJENju1/PIO/qaESIP/3rRE/Gw1fmfX+F1wN+jXQao
 WXw2JW/IUQG0TQlpTnEqPQQu+H48dX58MbpNVSLy2O7Z4XiMRDG2HkEduyJYGm+P
 37pfgiTH9Vj7MJ0EnNK3lLrQmF1l+yNHIjZUGLPEjbKmXSzJYPHwNhtC5U9/QooY
 igRwKC51bBw6of6pPaIYP6nxQeaNVgI3MaOnJ1+glLc0uQuy5mc4gODL6yCEkvuR
 WCsyJi226m/dBD+ZgejSet7kJS3JG4dR0GuqZkJ22DS5wKbwKrgXfOiVl+xrgCwR
 FqbvnZbscr+jt/xFJsAT5zqtvHNgxx37XVwkV3nHsKX8UugYg3rCB5T/mlgNj+m/
 Cg5BePP84O1NMJHYXSj7Wo6BYYoFJO8ucT0uIKpcci3UyvtqWcMXzptNjkAtylw1
 P+0EtP7HL4jBLJ5Snd0Je47w2mztmaJmqCc9LU8odznlFbaJ25X3chf3zqAoKdpY
 Lqe1XWxi5HtLNmuX/NsNhw0tdxuSiH5e2r7yM5Bwtm4uh4Yx9Ab9TEtloF3u+en5
 ALR88cryxbP0zu0K/HFUeoM3v7mqH3x29NqAsSpY1D6p87308FUa1rkvYMlHwcFD
 Y2W2iZhmxnE5Bi9OTpfDgGQYNEUiELWmMDi3S3aSwb0QM9UWsi043LGMQfpG5QCn
 +xKTKJDNJsHAX5jYDuDY
 =v7l/
 -----END PGP SIGNATURE-----

Merge tag 'for-v3.19' of git://git.infradead.org/battery-2.6

Pull power supply updates from Sebastian Reichel::
 "Power supply and reset changes for the v3.19 series

   - update power/reset drivers to use kernel restart handler
   - add power off driver for i.mx6
   - add DT support for gpio-charger"

* tag 'for-v3.19' of git://git.infradead.org/battery-2.6:
  power: reset: adjust priority of simple syscon reboot driver
  power: ds2782_battery: Simplify the PM hooks
  power/reset: brcmstb: Register with kernel restart handler
  power/reset: hisi: Register with kernel restart handler
  power/reset: keystone: Register with kernel restart handler
  power/reset: axxia: Register with kernel restart handler
  power/reset: xgene: Register with kernel restart handler
  power/reset: xgene: Use mdelay instead of jiffies based timeout
  power/reset: xgene: Use local variable dev instead of pdev->dev
  power/reset: xgene: Drop devm_kfree
  power/reset: xgene: Return -ENOMEM if out of memory
  power/reset: vexpress: Register with kernel restart handler
  power: reset: imx-snvs-poweroff: add power off driver for i.mx6
  power: gpio-charger: add device tree support
  dt-bindings: document gpio-charger bindings
2014-12-15 17:36:45 -08:00
Linus Torvalds e6b5be2be4 Driver core patches for 3.19-rc1
Here's the set of driver core patches for 3.19-rc1.
 
 They are dominated by the removal of the .owner field in platform
 drivers.  They touch a lot of files, but they are "simple" changes, just
 removing a line in a structure.
 
 Other than that, a few minor driver core and debugfs changes.  There are
 some ath9k patches coming in through this tree that have been acked by
 the wireless maintainers as they relied on the debugfs changes.
 
 Everything has been in linux-next for a while.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
 53kAoLeteByQ3iVwWurwwseRPiWa8+MI
 =OVRS
 -----END PGP SIGNATURE-----

Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core update from Greg KH:
 "Here's the set of driver core patches for 3.19-rc1.

  They are dominated by the removal of the .owner field in platform
  drivers.  They touch a lot of files, but they are "simple" changes,
  just removing a line in a structure.

  Other than that, a few minor driver core and debugfs changes.  There
  are some ath9k patches coming in through this tree that have been
  acked by the wireless maintainers as they relied on the debugfs
  changes.

  Everything has been in linux-next for a while"

* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
  Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
  fs: debugfs: add forward declaration for struct device type
  firmware class: Deletion of an unnecessary check before the function call "vunmap"
  firmware loader: fix hung task warning dump
  devcoredump: provide a one-way disable function
  device: Add dev_<level>_once variants
  ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
  ath: use seq_file api for ath9k debugfs files
  debugfs: add helper function to create device related seq_file
  drivers/base: cacheinfo: remove noisy error boot message
  Revert "core: platform: add warning if driver has no owner"
  drivers: base: support cpu cache information interface to userspace via sysfs
  drivers: base: add cpu_device_create to support per-cpu devices
  topology: replace custom attribute macros with standard DEVICE_ATTR*
  cpumask: factor out show_cpumap into separate helper function
  driver core: Fix unbalanced device reference in drivers_probe
  driver core: fix race with userland in device_add()
  sysfs/kernfs: make read requests on pre-alloc files use the buffer.
  sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
  fs: sysfs: return EGBIG on write if offset is larger than file size
  ...
2014-12-14 16:10:09 -08:00
Linus Torvalds 6cd94d5e57 ARM: SoC platform changes for 3.19
New and updated SoC support, notable changes include:
 
 * bcm: brcmstb SMP support
 * bcm: initial iproc/cygnus support
 * exynos: Exynos4415 SoC support
 * exynos: PMU and suspend support for Exynos5420
 * exynos: PMU support for Exynos3250
 * exynos: pm related maintenance
 * imx: new LS1021A SoC support
 * imx: vybrid 610 global timer support
 * integrator: convert to using multiplatform configuration
 * mediatek: earlyprintk support for mt8127/mt8135
 * meson: meson8 soc and l2 cache controller support
 * mvebu: Armada 38x CPU hotplug support
 * mvebu: drop support for prerelease Armada 375 Z1 stepping
 * mvebu: extended suspend support, now works on Armada 370/XP
 * omap: hwmod related maintenance
 * omap: prcm cleanup
 * pxa: initial pxa27x DT handling
 * rockchip: SMP support for rk3288
 * rockchip: add cpu frequency scaling support
 * shmobile: r8a7740 power domain support
 * shmobile: various small restart, timer, pci apmu changes
 * sunxi: Allwinner A80 (sun9i) earlyprintk support
 * ux500: power domain support
 
 Overall, a significant chunk of changes, coming mostly from
 the usual suspects: omap, shmobile, samsung and mvebu, all of
 which already contain a lot of platform specific code in
 arch/arm.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIVAwUAVIcjyGCrR//JCVInAQJJCRAA1Tm+HZGiAiTvXEAcm/T9tIA08uqtawHt
 cqyEAUyrnE8QxE4EhUd2pTw4EunVusqKF5EsDxOzw7b3ukUdLAWZE7bqBOSIJLqn
 hrfsQQ8dXLbyC7T/CHPnBVeM+pn9LiIc9qzpZ0YToiMnHBBI4vKFQntBjd31yoRE
 hN08I6AmDjQolOzzlqR1fuM0uZaKiHIcytdauTt3Vfqgg7FTHcTy3u1kClHTR1Lp
 m/KuDothGpR5OKjSnUQz7EO5V3KJEnaKey8z2xM1a7DLLAvJ6r2+DUaDopv9Dbz1
 W/V3H7fi5tLvillVa8xmlmzqWZbPc1xw8MWqvHZSWIMRZqloAHpC1VWKn0ZuH4SW
 5Bj4ubSrpYjJxjKYfrxtjmuzru3A2jWBNTSP5A4nsny0C3AUsXkfRmRS0VNdegF8
 sUdQ1MF8vEMpQT3QPH88+ccFHeIgqbcayhKqLPf7r8q0kwlym5N7Y2amU2A/O6qz
 +324r+yzfSA70VgJZ5EhXxWVDOPB4Lc8EtoWnH6T/kjncIMwzEsbEbyB3X1OaREW
 pVn3PNo06VjHLYoiHX+8G99pOFR/JZvaQs6jGCXLs+Orjp5WfP+kafkWqcB5GAKU
 Pfd3AQsl6rKAITdu0XsTdPiICNS4CmBiWYPepQsTa3pQaNgB7fwZNQKelNRIdGc+
 dF1lnQ7CXLQ=
 =lFoH
 -----END PGP SIGNATURE-----

Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC platform changes from Arnd Bergmann:
 "New and updated SoC support, notable changes include:

   - bcm:
        brcmstb SMP support
        initial iproc/cygnus support
   - exynos:
        Exynos4415 SoC support
        PMU and suspend support for Exynos5420
        PMU support for Exynos3250
        pm related maintenance
   - imx:
        new LS1021A SoC support
        vybrid 610 global timer support
   - integrator:
        convert to using multiplatform configuration
   - mediatek:
        earlyprintk support for mt8127/mt8135
   - meson:
        meson8 soc and l2 cache controller support
   - mvebu:
        Armada 38x CPU hotplug support
        drop support for prerelease Armada 375 Z1 stepping
        extended suspend support, now works on Armada 370/XP
   - omap:
        hwmod related maintenance
        prcm cleanup
   - pxa:
        initial pxa27x DT handling
   - rockchip:
        SMP support for rk3288
        add cpu frequency scaling support
   - shmobile:
        r8a7740 power domain support
        various small restart, timer, pci apmu changes
   - sunxi:
        Allwinner A80 (sun9i) earlyprintk support
   - ux500:
        power domain support

  Overall, a significant chunk of changes, coming mostly from the usual
  suspects: omap, shmobile, samsung and mvebu, all of which already
  contain a lot of platform specific code in arch/arm"

* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (187 commits)
  ARM: mvebu: use the cpufreq-dt platform_data for independent clocks
  soc: integrator: Add terminating entry for integrator_cm_match
  ARM: mvebu: add SDRAM controller description for Armada XP
  ARM: mvebu: adjust mbus controller description on Armada 370/XP
  ARM: mvebu: add suspend/resume DT information for Armada XP GP
  ARM: mvebu: synchronize secondary CPU clocks on resume
  ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume
  ARM: mvebu: Armada XP GP specific suspend/resume code
  ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume
  ARM: mvebu: implement suspend/resume support for Armada XP
  clk: mvebu: add suspend/resume for gatable clocks
  bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration
  bus: mvebu-mbus: suspend/resume support
  clocksource: time-armada-370-xp: add suspend/resume support
  irqchip: armada-370-xp: Add suspend/resume support
  ARM: add lolevel debug support for asm9260
  ARM: add mach-asm9260
  ARM: EXYNOS: use u8 for val[] in struct exynos_pmu_conf
  power: reset: imx-snvs-poweroff: add power off driver for i.mx6
  ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
  ...
2014-12-09 14:38:28 -08:00
Stefan Agner b81180b3fd power: reset: adjust priority of simple syscon reboot driver
Currently, all restart handler use the priority 128, including
watchdogs. Probably most SoC have a watchdog, and some of them
register it also as a restart handler. But if a SoC specifies
a dedicated reboot capability using this syscon driver, this is
usually the preferred reboot method. Hence, raise the priority
of this driver to 192.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2014-12-03 20:38:30 +01:00
Robin Gong 3db47dc0ae power: reset: imx-snvs-poweroff: add power off driver for i.mx6
This driver register pm_power_off with snvs power off function. If
your boards NOT use PMIC_ON_REQ to turn on/off external pmic, or use
other pin to do, please disable the driver in dts, otherwise, your
pm_power_off maybe overwrote by this driver.

Signed-off-by: Robin Gong <b38343@freescale.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2014-11-23 14:57:11 +08:00
Guenter Roeck 6136c41ae9 power/reset: brcmstb: Register with kernel restart handler
Register with kernel restart handler instead of setting arm_pm_restart directly.

Cc: Marc Carino <marc.ceeeee@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2014-11-17 03:07:10 +01:00
Guenter Roeck 6724534c79 power/reset: hisi: Register with kernel restart handler
Register with kernel restart handler instead of setting arm_pm_restart directly.

Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2014-11-17 03:07:10 +01:00
Guenter Roeck f59a42d4e1 power/reset: keystone: Register with kernel restart handler
Register with kernel restart handler instead of setting arm_pm_restart directly.

Move notifier registration to the end of the probe function to avoid having to
implement error handling.

Cc: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2014-11-17 03:07:10 +01:00
Guenter Roeck fcf01c51f0 power/reset: axxia: Register with kernel restart handler
Register with kernel restart handler instead of setting arm_pm_restart
directly.

Cc: Anders Berg <anders.berg@lsi.com>
Tested-by: Anders Berg <anders.berg@avagotech.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2014-11-17 03:07:10 +01:00
Guenter Roeck 8f57f2310f power/reset: xgene: Register with kernel restart handler
Register with kernel restart handler instead of setting arm_pm_restart directly.

This patch also addresses the following compile warning.

drivers/power/reset/xgene-reboot.c: In function 'xgene_reboot_probe':
drivers/power/reset/xgene-reboot.c:77:17: warning:
	assignment from incompatible pointer type [enabled by default]

The warning was due to a mismatch between the type of arm_pm_restart
and the restart function.

Cc: Loc Ho <lho@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2014-11-17 03:07:09 +01:00
Guenter Roeck 745e19764a power/reset: xgene: Use mdelay instead of jiffies based timeout
jiffies are not running at this stage of system shutdown, meaning an
error in the reset function would never be reported. Replace with mdelay().

Cc: Loc Ho <lho@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2014-11-17 03:07:09 +01:00
Guenter Roeck 43160718d9 power/reset: xgene: Use local variable dev instead of pdev->dev
Using a local variable dev to point to the device is simpler then repeatedly
dereferencing pdev->dev.

Cc: Loc Ho <lho@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2014-11-17 03:07:09 +01:00
Guenter Roeck 22ecd65f40 power/reset: xgene: Drop devm_kfree
Calling devm_kfree is unnecessary. Drop it.

Cc: Loc Ho <lho@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2014-11-17 03:07:09 +01:00
Guenter Roeck ef288f9f65 power/reset: xgene: Return -ENOMEM if out of memory
It is customary to return an error code of -ENOMEM if the system
is out of memory. Also, in that case, the infrastructure will report
an error, so it is unnecessary to report it again.

Cc: Loc Ho <lho@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2014-11-17 03:07:09 +01:00
Guenter Roeck 46c99ac662 power/reset: vexpress: Register with kernel restart handler
Use the kernel restart handler instead of setting arm_pm_restart directly.
This allows for more than one restart handler in the system.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2014-11-17 03:07:08 +01:00
Robin Gong b8e64eea41 power: reset: imx-snvs-poweroff: add power off driver for i.mx6
This driver register pm_power_off with snvs power off function. If
your boards NOT use PMIC_ON_REQ to turn on/off external pmic, or use
other pin to do, please disable the driver in dts, otherwise, your
pm_power_off maybe overwrote by this driver.

Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2014-11-17 03:07:08 +01:00
Alexandre Belloni f0a0a58e6f ARM: at91: move sdramc/ddrsdr header to include/soc/at91
Move the (DDR) SDRAM controller headers to include/soc/at91 to remove the
dependency on mach/ headers from the at91-reset driver.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-11-13 12:03:44 +01:00
Greg Kroah-Hartman a8a93c6f99 Merge branch 'platform/remove_owner' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux into driver-core-next
Remove all .owner fields from platform drivers
2014-11-03 19:53:56 -08:00
Alexandre Belloni 7cb4e717d4 power: reset: at91-reset: fix power down register
In the case of at91sam9g45_restart(), the driver is writing
AT91_DDRSDRC_LPCB_POWER_DOWN to AT91_DDRSDRC_RTR, this should actually be
AT91_DDRSDRC_LPR.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-10-22 10:08:22 +02:00
Wolfram Sang 5938ee2bb2 power: reset: drop owner assignment from platform_drivers
A platform_driver does not need to set an owner, it will be populated by the
driver core.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-10-20 16:21:28 +02:00
Linus Torvalds 50fa86172b power supply and reset changes for the v3.18 series
- Initial support for the following chips
   * max77836 (charger)
   * max14577 (charger)
   * bq27742 (battery gauge)
   * ltc2952 (poweroff)
   * stih416 (restart)
   * syscon-reboot (restart)
   * gpio-restart (restart)
  - cleanup of power supply core
  - misc. fixes in power supply and reset drivers
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABCgAGBQJUOWD7AAoJENju1/PIO/qaj5QP/AtbG96NRpX6Ou8W+qulhSbe
 npTKItRMERZhV+lJUAdmLxQq8Cy6I5Cobdj140oIM6HIKZ7Dh6jChxd2t+RCLsO0
 Y16VMq45L9E/mQuVCLqSSNCPKrRjbF7hW+8gpym/Yc846o3Fv8nhTQzkWxCsVrDR
 rNerRnrUyvKpqRpCN88u4ZuOHjm/146nZtTsAzvL8nGnQBZFJHv4eu7D5nwSN0QS
 FrLiI/mE7h1KFcdK5LrZf51IfEP9w4RVV3vs1wEuP0iPS5dguv2dNzXXVZa5eD/2
 AYSSouVKkgdwryLAvIIaDLD405UYl5Xgt5J6d+QKXxm2+eeZMEY36+PEK5WtRtBX
 CykzO2BgvxyOdz2HU9D8irR1Li71jVSWwQITMJ6bQsbKEQAhltmkmsTOxtqB+ekd
 254rKcKWTqllmEhg1LR8PCidf8OZNEcKzXi4XmQdQIcKNF9tvdTXP5c0/FzuIAlQ
 tqWZW1kQK6/TTfx+XxeeszJWY5VknIaka2Bi83pOZYtu94CtUFBdEVkpaYmC433+
 qLOto7VMy+AKYViTJJDDEnSEFiLNZz/zF+SUDf+YB1RelULSF3zC8CbDcZQa5fNm
 4qTU1fl2gGrIZ1jDPPihm6xP8r9WkeuQWEytG2UJZoa+l4XmzfLHBUUDVo0zqTd3
 txfmKca8Y3GhXGwINi1m
 =sj9S
 -----END PGP SIGNATURE-----

Merge tag 'for-v3.18' of git://git.infradead.org/battery-2.6

Pull power supply and reset updates from Sebastian Reichel:
 - Initial support for the following chips
   * max77836 (charger)
   * max14577 (charger)
   * bq27742 (battery gauge)
   * ltc2952 (poweroff)
   * stih416 (restart)
   * syscon-reboot (restart)
   * gpio-restart (restart)
 - cleanup of power supply core
 - misc fixes in power supply and reset drivers

* tag 'for-v3.18' of git://git.infradead.org/battery-2.6: (48 commits)
  power: ab8500_fg: Fix build warning
  Documentation: charger: max14577: Update the date of introducing ABI
  power: reset: corrections for simple syscon reboot driver
  Documentation: power: reset: Add documentation for generic SYSCON reboot driver
  power: reset: Add generic SYSCON register mapped reset
  bq27x00_battery: Fix flag reading for bq27742
  power: reset: use restart_notifier mechanism for msm-poweroff
  power: Add simple gpio-restart driver
  power: reset: st: Provide DT bindings for ST's Power Reset driver
  power: reset: Add restart functionality for STiH41x platforms
  power: charger-manager: Fix NULL pointer exception with missing cm-fuel-gauge
  power: max14577: Fix circular config SYSFS dependency
  power: gpio-charger: do not use gpio value directly
  power: max8925: Use of_get_child_by_name
  power: max8925: Fix NULL ptr dereference on memory allocation failure
  bq27x00_battery: Add support to bq27742
  Documentation: charger: max14577: Document exported sysfs entry
  devicetree: mfd: max14577: Add device tree bindings document
  power: max17040: Add ID for MAX77836 Fuel Gauge block
  charger: max14577: Configure battery-dependent settings from DTS and sysfs
  ...

Conflicts:
	drivers/power/reset/Kconfig
	drivers/power/reset/Makefile
2014-10-15 06:56:23 +02:00
Linus Torvalds 93834c6419 Immutable branch with restart handler patches for v3.18
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJUJQ8/AAoJEMsfJm/On5mBMNgP+QEUHpRKJaOGU3jX/ftHH/t3
 EoNUx7lZt6Q0c9MB2ySAxILYpWUujc9N0tDkRDyW7mTWunF8gEGiRN+iKaSbzcUN
 Y4VffRAbxBasIaBqRtpDl08ycODh6Xu1t8sAao03DdhnMNLGNNO79s3UFHsubdTC
 cXx9mfYR/2SHV/0BXiFvKi8ovdqUspdp9cyZO/qc0PVFGbsADx3MNGGzkvWfgvcE
 6vXnKnUkZrNl5JPiG77kTKZnDsjEMXggmA9DGWKijFCJjGIbuLiuIDf63Zp+eQ52
 mJMRA+ViP/dDgAxY1dkWBcF5nOBT1vTYwLfy69jEoQeHzcomiHVoDKmCSBOpeAEH
 G8VoasWKWYpYnlcOJb+XgkA3QTe6mOPgAPzNsbYr0Ep7hMFw66mOQgKbgi6k4Qts
 HHimG9pnBYpPlBUfvNh+6K4dHAm0C2IyoZyMhKWsyFH6hkhS8TVM8j0gPR8rTTmk
 0a9/e2vxcFnfBe3UAJaqzWRVFsBkOHrTNpG1hvID3Oq8IeywSBXw2VMSR93+mwaB
 sa/GCZKlqHGpOfmtILlhiXQX0E/tTHmcrI2VqyCpX0J2CW+MiGvkcGOwKHOJciSA
 Cj9D68y837QU/DCpMQ6ec/5wqWqZKz8yQb8kxb6vJcL19JcVKdAiPzbuOI49C3Ux
 YxDWoUutzDfVoUD5RhcJ
 =cP1w
 -----END PGP SIGNATURE-----

Merge tag 'restart-handler-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull restart handler infrastructure from Guenter Roeck:
 "This series was supposed to be pulled through various trees using it,
  and I did not plan to send a separate pull request.  As it turns out,
  the pinctrl tree did not merge with it, is now upstream, and uses it,
  meaning there are now build failures.

  Please pull this series directly to fix those build failures"

* tag 'restart-handler-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  arm/arm64: unexport restart handlers
  watchdog: sunxi: register restart handler with kernel restart handler
  watchdog: alim7101: register restart handler with kernel restart handler
  watchdog: moxart: register restart handler with kernel restart handler
  arm: support restart through restart handler call chain
  arm64: support restart through restart handler call chain
  power/restart: call machine_restart instead of arm_pm_restart
  kernel: add support for kernel restart handler call chain
2014-10-10 16:38:02 -04:00
Feng Kan afaebbdbd4 power: reset: corrections for simple syscon reboot driver
This patch is to fix some bugs in reboot driver. Which includes auto selection
of the MFD_SYSCON for the driver, use of container to locate restart handler,
correction of the count down failure timer and ordering of the header file.

Signed-off-by: Feng Kan <fkan@apm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
[ sre: return err instead of 0 in syscon_reboot_probe() ]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2014-10-03 04:32:08 +02:00
Feng Kan 09fb07bcaf power: reset: Add generic SYSCON register mapped reset
Add a generic SYSCON register mapped reset mechanism.

Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2014-10-01 04:21:05 +02:00
Pramod Gurav 18a702e0de power: reset: use restart_notifier mechanism for msm-poweroff
This change replaces use of arm_pm_restart with recently introduced
reset mechanism in Linux kernel called restart_notifier.

Choosing priority 128, which is default priority, as according to
documentation, this mechanism is sufficient to restart the entire system.

Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Josh Cartwright <joshc@codeaurora.org>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-pm@vger.kernel.org

Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2014-09-26 19:54:33 +02:00
David Riley 371bb20d69 power: Add simple gpio-restart driver
This driver registers a restart handler to set a GPIO line high/low
to reset a board based on devicetree bindings.

Signed-off-by: David Riley <davidriley@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2014-09-26 19:51:15 +02:00
Sebastian Reichel 1670d8569e Immutable branch with restart handler patches for v3.18
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJUJQ8/AAoJEMsfJm/On5mBMNgP+QEUHpRKJaOGU3jX/ftHH/t3
 EoNUx7lZt6Q0c9MB2ySAxILYpWUujc9N0tDkRDyW7mTWunF8gEGiRN+iKaSbzcUN
 Y4VffRAbxBasIaBqRtpDl08ycODh6Xu1t8sAao03DdhnMNLGNNO79s3UFHsubdTC
 cXx9mfYR/2SHV/0BXiFvKi8ovdqUspdp9cyZO/qc0PVFGbsADx3MNGGzkvWfgvcE
 6vXnKnUkZrNl5JPiG77kTKZnDsjEMXggmA9DGWKijFCJjGIbuLiuIDf63Zp+eQ52
 mJMRA+ViP/dDgAxY1dkWBcF5nOBT1vTYwLfy69jEoQeHzcomiHVoDKmCSBOpeAEH
 G8VoasWKWYpYnlcOJb+XgkA3QTe6mOPgAPzNsbYr0Ep7hMFw66mOQgKbgi6k4Qts
 HHimG9pnBYpPlBUfvNh+6K4dHAm0C2IyoZyMhKWsyFH6hkhS8TVM8j0gPR8rTTmk
 0a9/e2vxcFnfBe3UAJaqzWRVFsBkOHrTNpG1hvID3Oq8IeywSBXw2VMSR93+mwaB
 sa/GCZKlqHGpOfmtILlhiXQX0E/tTHmcrI2VqyCpX0J2CW+MiGvkcGOwKHOJciSA
 Cj9D68y837QU/DCpMQ6ec/5wqWqZKz8yQb8kxb6vJcL19JcVKdAiPzbuOI49C3Ux
 YxDWoUutzDfVoUD5RhcJ
 =cP1w
 -----END PGP SIGNATURE-----

Merge tag 'tags/restart-handler-for-v3.18' into next

Immutable branch with restart handler patches for v3.18
2014-09-26 19:45:11 +02:00
Lee Jones f0745f3696 power: reset: Add restart functionality for STiH41x platforms
This driver adds the restart functionality for STiH415 and STiH416
platforms from STMicroelectronics.  This driver registers an
arm_pm_restart function to reset the platform.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2014-09-26 17:34:15 +02:00
Guenter Roeck 0713e143c9 power/restart: call machine_restart instead of arm_pm_restart
machine_restart is supported on non-ARM platforms, and and ultimately
calls arm_pm_restart, so dont call arm_pm_restart directly but use the
more generic function.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2014-09-26 00:00:11 -07:00
Linus Walleij 0e545f57b7 power: reset: driver for the Versatile syscon reboot
This driver enabled us to drive the reboot of the Versatile family
of ARM reference boards. Even though only the RealView boards are
supported initially, these boards all have the same procedure for
reboot:

- Write a magic value into an unlocking register
- Write another magic value into a reset control register

The driver will be reusable for Versatile and possibly also the
Integrator family of reference boards.

Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2014-09-26 00:25:59 +02:00
René Moll 6647156c00 power: reset: add LTC2952 poweroff driver
This adds a driver for the LTC2952, an external power control chip,
which signals the OS to shut down. Additionally this driver lets the
kernel power down the board.

Signed-off-by: René Moll <rene.moll@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2014-09-16 11:01:39 +02:00
Mark Brown d3ed534cca power/reset: xgene-reset: Fix prototype of xgene_restart()
The xgene-reset driver uses xgene_restart() as arm_pm_restart() but that
function should take an enum reset_type as the first argument rather than
a char. Fix this; the paramter is not referenced in the implementation.

Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2014-09-06 20:59:07 +02:00
Nicolas Ferre 405a72c5e7 power: reset: at91-poweroff: fix wakeup status register index
The wakeup status is read from Shutdown Status Register and not the
SHDW_CR which is the one at address 0.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-09-01 18:40:44 +02:00
Nicolas Ferre 94d450edfd ARM: at91/power/reset: fix Kconfig "depends on" directive
MACH_AT91 doesn't exist so we can't "depend" on it. Fix the typo
by using the proper ARCH_AT91 config option.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-09-01 18:39:24 +02:00
Nicolas Ferre e657ce689a AT91 reset, poweroff and ram drivers
This tag holds the various new drivers introduced to move code that used to be
 in mach-at91 over to the proper frameworks.
 
 These files are the reboot and poweroff code for all AT91 SoCs but the RM9200,
 and the ram controller driver is not doing much at the time, except for grabing
 the RAM clock in order to leave it always enabled.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJTx4LlAAoJEBx+YmzsjxAggooP/0xIMF568hWNLWMOBLNyeXLP
 SJUCBZw1kLqhw8K3nPV5GAmfGxgCCZ3uvUfMdIgJzSN+NtcuvQR2+ui2Bj1nzRRQ
 y6ZAmoHEJHveNd3SoLpuE5s4KFwTBFblcBXHVSwIZzMcCioBxFWtcPupkIVoqt/z
 s/gN5w9BsSCvqjtmYSTp8XTza9y7hx9Pmdpc1uzkP/WJbXtxyQX50NlpILQ1r7WW
 WNOMRXOpv/JH+EHFtS7vMMvn+fQ94RVI209+Z2wez13H87C8MZF4N972vRHkmBuG
 Uv2ZowFRo8T0YjJZfmyfWyg3C9fMOcQeOURAGO/FIavf0WJ+7/hmdZ9jymTpaA3b
 WwZ+qgajMMdOk2ojW36vfueOqeuXx7bxGKWocXO/Rk00ZpN8Y2qFqmsJL5WNYVoN
 SDod+nzYHA4ShyZFDiXoAf3R/+gjb9RvCJ0ZvjkdHUeU8GYHhXjDLPp1Ng7oDBut
 szDE8FfWGpb5UsjFSdKfSsU2Xp3lqZ6fv89qiGYGwz7OqKRz2E0d8zm/EHoD87RR
 jx9e4pWvk++Vouk/zCRZVb+HrGtN9FbZKfRq6xx1pAO+V2NCmq8ttcPH2BuN1K3T
 quFRb6YBTfNfgVKPjbPsQ4QOuCR4juIZSubRhQEi7/Uie5aR/9q6Lz/pYbzitYjJ
 qHR5nj7sL/WwJlfgFgbi
 =YBPz
 -----END PGP SIGNATURE-----

Merge tag 'at91-drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux

Pull AT91 reset, poweroff and ram drivers from Maxime Ripard:
 "This tag holds the various new drivers introduced to move code that used to be
  in mach-at91 over to the proper frameworks.

  These files are the reboot and poweroff code for all AT91 SoCs but the RM9200,
  and the ram controller driver is not doing much at the time, except for grabing
  the RAM clock in order to leave it always enabled."

Conflicts:
	arch/arm/mach-at91/Kconfig
2014-08-25 15:35:26 +02:00
Linus Torvalds b3345d7c57 ARM: SoC platform changes for 3.17
This is the bulk of new SoC enablement and other platform changes for 3.17:
 
 * Samsung S5PV210 has been converted to DT and multiplatform
 * Clock drivers and bindings for some of the lower-end i.MX 1/2 platforms
 * Kirkwood, one of the popular Marvell platforms, is folded into the
   mvebu platform code, removing mach-kirkwood.
 * Hwmod data for TI AM43xx and DRA7 platforms.
 * More additions of Renesas shmobile platform support
 * Removal of plat-samsung contents that can be removed with S5PV210 being
   multiplatform/DT-enabled and the other two old platforms being removed.
 
 New platforms (most with only basic support right now):
 
 * Hisilicon X5HD2 settop box chipset is introduced
 * Mediatek MT6589 (mobile chipset) is introduced
 * Broadcom BCM7xxx settop box chipset is introduced
 
 + as usual a lot other pieces all over the platform code.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.14 (GNU/Linux)
 
 iQIcBAABAgAGBQJT5Dp+AAoJEIwa5zzehBx3w1sP/0vjT/LQOmC8Lv8RW2Ley2ua
 hNu3HcNPnT/N40JEdU9YNv3q0fdxGgcfKj011CNN+49zPSUf1xduk2wfCAk9yV50
 8Sbt1PfDGm1YyUugGN420CzI431pPoM1OGXHZHkAmg+2J286RtUi3NckB//QDbCY
 QhEjhpYc9SXhAOCGwmB4ab7thOljOFSPzKTLMTu3+PNI5zRPRgkDkt6w9XlsAYmB
 nuR271BnzsROkMzAjycwaJ3kdim7wqrMRfk8g96o0jHSF5qf4zsT5uWYYAjTxdUQ
 8Ajz6zjeHe4+95TwTDcq+lCX6rDLZgwkvCAc6hFbeg0uR7Dyek0h6XMEYtwdjaiU
 KNPwOENrYdENNDAGRpkFp1x4h/rY9Plfru0bBo5o6t7aPBvmNeCDzRtlTtLiUNDV
 dG8sfDMtrS/wFHVjylDSQ60Mb+wuW0XneC8D7chY/iRhIllUYi6YXXvt+/tH5C20
 oYDOWqqcDFSb0sJhE5pn4KBV82ZaHx9jMBWGLl+erg2sDX/SK8SxOkLqKYZKtKB5
 0leOGE3Y+C70xt3G9HftLz2sAvvt+C8UPsApPT+dHNE401TWJOYx6LphPkQKjeeK
 P1iwKi+It3l+FaBypgJy/LeMQRy7EyvDBK2I5WoVL/R2qq14EmP1ui3Tthjj0bhq
 tBBof6P9c8OnRVj1Lz3R
 =5TJ6
 -----END PGP SIGNATURE-----

Merge tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC platform changes from Olof Johansson:
 "This is the bulk of new SoC enablement and other platform changes for
  3.17:

   - Samsung S5PV210 has been converted to DT and multiplatform
   - Clock drivers and bindings for some of the lower-end i.MX 1/2
     platforms
   - Kirkwood, one of the popular Marvell platforms, is folded into the
     mvebu platform code, removing mach-kirkwood
   - Hwmod data for TI AM43xx and DRA7 platforms
   - More additions of Renesas shmobile platform support
   - Removal of plat-samsung contents that can be removed with S5PV210
     being multiplatform/DT-enabled and the other two old platforms
     being removed

  New platforms (most with only basic support right now):

   - Hisilicon X5HD2 settop box chipset is introduced
   - Mediatek MT6589 (mobile chipset) is introduced
   - Broadcom BCM7xxx settop box chipset is introduced

  + as usual a lot other pieces all over the platform code"

* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
  ARM: hisi: remove smp from machine descriptor
  power: reset: move hisilicon reboot code
  ARM: dts: Add hix5hd2-dkb dts file.
  ARM: debug: Rename Hi3716 to HIX5HD2
  ARM: hisi: enable hix5hd2 SoC
  ARM: hisi: add ARCH_HISI
  MAINTAINERS: add entry for Broadcom ARM STB architecture
  ARM: brcmstb: select GISB arbiter and interrupt drivers
  ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
  ARM: configs: enable SMP in bcm_defconfig
  ARM: add SMP support for Broadcom mobile SoCs
  Documentation: arm: misc updates to Marvell EBU SoC status
  Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
  ARM: mvebu: fix build without platforms selected
  ARM: mvebu: add cpuidle support for Armada 38x
  ARM: mvebu: add cpuidle support for Armada 370
  cpuidle: mvebu: add Armada 38x support
  cpuidle: mvebu: add Armada 370 support
  cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
  ARM: mvebu: export the SCU address
  ...
2014-08-08 11:14:29 -07:00
Haojian Zhuang 4a9b373718 power: reset: move hisilicon reboot code
Move reboot code from hisilicon platform driver into reset driver.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-30 22:32:21 -07:00
Marc Carino 030494e750 power: reset: Add reboot driver for brcmstb
Add support for reboot functionality on boards with ARM-based
Broadcom STB chipsets. Make it built-in by default for ARCH_BRCMSTB,
but allow it to be configurable under COMPILE_TEST.

Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2014-07-23 13:49:23 +02:00
Bjorn Helgaas 661468b4e2 power/reset: Fix GPL v2 license string typo
Per license_is_gpl_compatible(), the MODULE_LICENSE() string for GPL v2 is
"GPL v2", not "GPLv2".  Use "GPL v2" so this module doesn't taint the
kernel.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2014-07-18 23:40:23 +02:00
Linus Walleij 86336ba4b7 power: poweroff: gpio: convert to use descriptors
This switches the GPIO poweroff driver to use GPIO descriptors
rather than numeral GPIOs. We get rid of the specific inversion
handling as GPIO descriptors know if they are active low or
high and can assert the line properly, so we do not need to
check the flag OF_GPIO_ACTIVE_LOW returned from the old call
of_get_gpio_flags() anymore.

Also convert to use managed resources and use dev_* message
printing while we're at it.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
2014-07-18 23:40:23 +02:00
Maxime Ripard ae499f0fad power: reset: Add AT91 poweroff driver
Add a driver to handle the shutdown of the Atmel SoCs. This code used to be
(and still is) in arch/arm/mach-at91. We didn't remove it yet so that we can
convert all the boards to using this driver, before removing it entirely in a
separate patch.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2014-07-15 13:40:34 +02:00
Maxime Ripard ecfe64d8c5 power: reset: Add AT91 reset driver
Implement the reset behaviour of the various AT91 SoCS in drivers/power/reset.

It used to be (and still is) located in arch/arm/mach-at91, and in order to
preserve bisectability is not removed yet, but every board should be converted
to use this driver instead.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2014-07-15 13:40:33 +02:00
Maxime Ripard 6ca4f46005 power: reset: Add if statement instead of multiple depends on
All the config option so far are depending on the POWER_RESET symbol

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2014-07-15 13:40:32 +02:00