Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return or break from the middle of the loop,
there is no put, thus causing a memory leak.
Hence, for function cpsw_probe_dt, create an extra label err_node_put
that puts the last used node and returns ret; modify the return
statements in the loop to save the return value in ret and goto this new
label.
For function cpsw_remove_dt, add an of_node_put before the break.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kvzalloc already zeroes the memory during the allocation.
pci_alloc_consistent calls dma_alloc_coherent directly.
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So the memset after these function is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix excessive stack usage in cxgb4, from Arnd Bergmann.
2) Missing skb queue lock init in tipc, from Chris Packham.
3) Fix some regressions in ipv6 flow label handling, from Eric Dumazet.
4) Elide flow dissection of local packets in FIB rules, from Petar
Penkov.
5) Fix TLS support build failure in mlx5, from Tariq Toukab.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
ppp: mppe: Revert "ppp: mppe: Add softdep to arc4"
net: dsa: qca8k: replace legacy gpio include
net: hisilicon: Use devm_platform_ioremap_resource
cxgb4: reduce kernel stack usage in cudbg_collect_mem_region()
tipc: ensure head->lock is initialised
tc-tests: updated skbedit tests
nfp: flower: ensure ip protocol is specified for L4 matches
nfp: flower: fix ethernet check on match fields
net/mlx5e: Provide cb_list pointer when setting up tc block on rep
net: phy: make exported variables non-static
net: sched: Fix NULL-pointer dereference in tc_indr_block_ing_cmd()
davinci_cpdma: don't cast dma_addr_t to pointer
net: openvswitch: do not update max_headroom if new headroom is equal to old headroom
net/mlx5e: Convert single case statement switch statements into if statements
net/mlx5: E-Switch, Reduce ingress acl modify metadata stack usage
net/mlx5e: Fix unused variable warning when CONFIG_MLX5_ESWITCH is off
net/mlx5e: Fix compilation error in TLS code
ipv6: fix static key imbalance in fl_create()
ipv6: fix potential crash in ip6_datagram_dst_update()
ipv6: tcp: fix flowlabels reflection for RST packets
...
dma_addr_t may be 64-bit wide on 32-bit architectures, so it is not
valid to cast between it and a pointer:
drivers/net/ethernet/ti/davinci_cpdma.c: In function 'cpdma_chan_submit_si':
drivers/net/ethernet/ti/davinci_cpdma.c:1047:12: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
drivers/net/ethernet/ti/davinci_cpdma.c: In function 'cpdma_chan_idle_submit_mapped':
drivers/net/ethernet/ti/davinci_cpdma.c:1114:12: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
drivers/net/ethernet/ti/davinci_cpdma.c: In function 'cpdma_chan_submit_mapped':
drivers/net/ethernet/ti/davinci_cpdma.c:1164:12: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
Solve this by using two separate members in 'struct submit_info'.
Since this avoids the use of the 'flag' member, the structure does
not even grow in typical configurations.
Fixes: 6670acacd5 ("net: ethernet: ti: davinci_cpdma: add dma mapped submit")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
Add XDP support based on rx page_pool allocator, one frame per page.
Page pool allocator is used with assumption that only one rx_handler
is running simultaneously. DMA map/unmap is reused from page pool
despite there is no need to map whole page.
Due to specific of cpsw, the same TX/RX handler can be used by 2
network devices, so special fields in buffer are added to identify
an interface the frame is destined to. Thus XDP works for both
interfaces, that allows to test xdp redirect between two interfaces
easily. Also, each rx queue have own page pools, but common for both
netdevs.
XDP prog is common for all channels till appropriate changes are added
in XDP infrastructure. Also, once page_pool recycling becomes part of
skb netstack some simplifications can be added, like removing
page_pool_release_page() before skb receive.
In order to keep rx_dev while redirect, that can be somehow used in
future, do flush in rx_handler, that allows to keep rx dev the same
while redirect. It allows to conform with tracing rx_dev pointed
by Jesper.
Also, there is probability, that XDP generic code can be extended to
support multi ndev drivers like this one, using same rx queue for
several ndevs, based on switchdev for instance or else. In this case,
driver can be modified like exposed here:
https://lkml.org/lkml/2019/7/3/243
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
That's possible to set channel num while interfaces are down. When
interface gets up it should resplit budget. This resplit can happen
after phy is up but only if speed is changed, so should be set before
this, for this allow it to happen while changing number of channels,
when interfaces are down.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
That's possible to set ring params while interfaces are down. When
interface gets up it uses number of descs to fill rx queue and on
later on changes to create rx pools. Usually, this resplit can happen
after phy is up, but it can be needed before this, so allow it to
happen while setting number of rx descs, when interfaces are down.
Also, if no dependency on intf state, move it to cpdma layer, where
it should be.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case if dma mapped packet needs to be sent, like with XDP
page pool, the "mapped" submit can be used. This patch adds dma
mapped submit based on regular one.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign OF node to CPSW slave devices, otherwise it is not possible to
bind e.g. DSA switch to them. Without this patch, the DSA code tries
to find the ethernet device by OF match, but fails to do so because
the slave device has NULL OF node.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bfe59032bd ("net: ethernet:
ti: cpsw: use cpsw as drv data")changes
the driver data to struct cpsw_common *cpsw. This is done
only in probe/remove but the suspend/resume functions are
still left with struct net_device *ndev. Hence fix both
suspend & resume also to fetch the updated driver data.
Fixes: bfe59032bd ("net: ethernet: ti: cpsw: use cpsw as drv data")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an arbitrary difference between the prototypes of
bus_find_device() and class_find_device() preventing their callers
from passing the same pair of data and match() arguments to both of
them, which is the const qualifier used in the prototype of
class_find_device(). If that qualifier is also used in the
bus_find_device() prototype, it will be possible to pass the same
match() callback function to both bus_find_device() and
class_find_device(), which will allow some optimizations to be made in
order to avoid code duplication going forward. Also with that, constify
the "data" parameter as it is passed as a const to the match function.
For this reason, change the prototype of bus_find_device() to match
the prototype of class_find_device() and adjust its callers to use the
const qualifier in accordance with the new prototype of it.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Kershner <david.kershner@unisys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: rafael@kernel.org
Acked-by: Corey Minyard <minyard@acm.org>
Acked-by: David Kershner <david.kershner@unisys.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for the I2C parts
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While data pass suspend, reuse of rx descriptors can be disabled using
channel state & lock from cpdma layer. For this, submit to a channel
has to be disabled using state != "not active" under lock, what is done
with this patch. The same submit is used to fill rx channel while
ndo_open, when channel is idled, so add idled submit routine that
allows to prepare descs for the channel. All this simplifies code and
helps to avoid dormant mode usage and send packets only to active
channels, avoiding potential race in later on changes. Also add missed
sync barrier analogically like in other places after stopping tx
queues.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only for consistency reasons, do it like in main cpsw.c module
and use ndev reference but not by means of slave.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to set ndev for drvdata when mainly cpsw reference is needed,
so correct this legacy decision.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dependency to TI CPTS from Common CLK framework COMMON_CLK to fix
allyesconfig build for Powerpc:
drivers/net/ethernet/ti/cpts.c: In function 'cpts_of_mux_clk_setup':
drivers/net/ethernet/ti/cpts.c:567:2: error: implicit declaration of function 'of_clk_parent_fill'; did you mean 'of_clk_get_parent_name'? [-Werror=implicit-function-declaration]
of_clk_parent_fill(refclk_np, parent_names, num_parents);
^~~~~~~~~~~~~~~~~~
of_clk_get_parent_name
Fixes: a3047a81ba ("net: ethernet: ti: cpts: add support for ext rftclk selection")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some CPTS instances, which can be found on KeyStone 2 1G Ethernet Switch
Subsystems, can control an external multiplexer that selects one of up to
32 clocks as time sync reference (RFTCLK) clock. This feature can be
configured through CPTS_RFTCLK_SEL register (offset: x08) in CPTS module
and can be represented as multiplexer clock.
Hence, introduce support for optional cpts-refclk-mux clock, which, once
defined will allow to select required CPTS RFTCLK by using
assigned-clock-parents DT property in board files.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to place CPTS properties in the child "cpts" DT node. For backward
compatibility - roll-back and read CPTS DT properties from parent node if
"cpts" node is not present.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_get_clk_from_child() instead of devm_clk_get() and this way allow
to group CPTS DT properties in sub-node for better code readability and
maintenance. Roll-back to devm_clk_get() if devm_get_clk_from_child()
fails for backward compatibility.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ability to set RX descriptor number, the reason - initially
"tx_max_pending" was set incorrectly, but the issue appears after
adding sanity check, so fix is for "sanity" patch.
Fixes: 37e2d99b59 ("ethtool: Ensure new ring parameters are within bounds during SRINGPARAM")
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's found while review and probably never happens, but real number
of queues is set per device, and error path should be per device.
So split error path based on usage_count.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes following (similar) warning reported by kbuild test robot:
In function ‘memcpy’,
inlined from ‘smsc75xx_init_mac_address’ at drivers/net/usb/smsc75xx.c:778:3,
inlined from ‘smsc75xx_bind’ at drivers/net/usb/smsc75xx.c:1501:2:
./include/linux/string.h:355:9: warning: argument 2 null where non-null expected [-Wnonnull]
return __builtin_memcpy(p, q, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/usb/smsc75xx.c: In function ‘smsc75xx_bind’:
./include/linux/string.h:355:9: note: in a call to built-in function ‘__builtin_memcpy’
I've replaced the offending memcpy with ether_addr_copy, because I'm
100% sure, that of_get_mac_address can't return NULL as it returns valid
pointer or ERR_PTR encoded value, nothing else.
I'm hesitant to just change IS_ERR into IS_ERR_OR_NULL check, as this
would make the warning disappear also, but it would be confusing to
check for impossible return value just to make a compiler happy.
I'm now changing all occurencies of memcpy to ether_addr_copy after the
of_get_mac_address call, as it's very likely, that we're going to get
similar reports from kbuild test robot in the future.
Fixes: a51645f70f ("net: ethernet: support of_get_mac_address new ERR_PTR error")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was NVMEM support added directly to of_get_mac_address, and it uses
nvmem_get_mac_address under the hood, so we can remove it. As
of_get_mac_address can now return ERR_PTR encoded error values, adjust to
that as well.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_ioremap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 03f66f0675 ("net: ethernet: ti: davinci_mdio: use devm_ioremap()")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix inconsistent IS_ERR and PTR_ERR in cpsw_probe,
The proper pointer to use is clk instead of mode.
This issue was detected with the help of Coccinelle.
Fixes: 83a8471ba2 ("net: ethernet: ti: cpsw: refactor probe to group common hw initialization")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to add support for a switchdev based cpsw driver,
move common ethtool functions to separate cpsw-ethtool.c file so that they
can be used across both drivers. It will simplify CPSW driver code
maintenance also.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch CPSW driver to use the new MAC SL API.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC SL submodule has a lot of common functions between many of TI SoCs
AM335x/AM437x/DRA7(AM57xx), Keystone 2 66AK2HK/E/L/G and K3 AM654, but
there are also differences especially in registers offsets and sets of
supported functions.
This patch introduces the MAC SL submodule API which is intended to provide
a common way to access the MAC SL submodule and hide HW integrations
details.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
move common hw init code in separate function as preparation for adding new
switchdev driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_addr_t for desc_mem_phys and desc_hw_addr to avoid types
conversions.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to add a switchdev based cpsw driver move the common
header definitions to cpsw_priv.h. The plan is to develop a new driver on
switchdev driver model and obsolete the current cpsw driver after all
required functions are added to the new driver. This patch allows the same
header file to be re-used on both drivers during the transition period.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework probe to group common hw initialization:
- group resources request at the beginning of the probe
- move net device initialization and registration at the end of the probe
- drop cpsw_slave_init
as preparation of refactoring of common hw initialization code to
separate function.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Davinci MDIO in most of the case implemented as module inside of TI
CPSW subsystem and fully depends on CPSW to be enabled, but historically
it's implemented as separate Platform device/driver and defined in DT files
in two ways:
- as standalone node
- as child node of CPSW subsystem.
In later case it's required to split CPSW subsystem "reg" property to
exclude MDIO I/O range which is not useful.
Hence, replace devm_ioremap_resource() with devm_ioremap() to allow define
full I/O range in parent CPSW subsystem without spliting.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not delete multicast supervisory packet's (SUPER) entries while flushing
multicast addresses from ALE table cpsw_ale_flush_multicast(). Those
entries have to be added/removed only explicitly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now CPSW ALE will set/clean Host port bit in Unregistered Multicast Flood
Mask (UNREG_MCAST_FLOOD_MASK) for every VLAN without checking if this port
belongs to VLAN or not when ALLMULTI mode flag is set for nedev. This is
working in non dual_mac mode, but in dual_mac - it causes
enabling/disabling ALLMULTI flag for both ports.
Hence fix it by adding additional parameter to cpsw_ale_set_allmulti() to
specify ALE port number for which ALLMULTI has to be enabled and check if
port belongs to VLAN before modifying UNREG_MCAST_FLOOD_MASK.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ALE_PORT_HOST define for host port in cpsw_ale_set_allmulti() instead
of constants.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use correct define ALE_SUPER for ALE Multicast Address Table Entry
Supervisory Packet (SUPER) bit setting instead of ALE_BLOCKED. No issues
were observed till now as it have never been set, but it's going to be used
by new CPSW switch driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop unnecessary wrapper function cpsw_tx_packet_submit() which is used
only in one place.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_alloc_etherdev_mqs() and simplify code.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop pinctrl_pm_select_default_state call from probe as default
pinctrl state is set by DD core.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use local variable struct device *dev in probe to simplify code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update cpsw_split_res() to accept struct cpsw_common instead of
struct net_device to simplify code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All TI drivers CPSW/NETCP can't work without ALE, hence simplify
build of those drivers by always linking cpsw_ale and drop
CONFIG_TI_CPSW_ALE config option.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both drivers CPSW and EMAC can't work without CPDMA, hence simplify build
of those drivers by always linking davinci_cpdma and drop TI_DAVINCI_CPDMA
config option.
Note. the davinci_emac driver module was changed to "ti_davinci_emac" to
make build work.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nishka Dasgupta
Fuqian Huang
Linus Torvalds
Arnd Bergmann
David S. Miller
Ivan Khoronzhuk
Marek Vasut
Keerthy
Suzuki K Poulose
Grygorii Strashko
Thomas Gleixner
Petr Štetiar
Wei Yongjun
YueHaibing