Exynos tracked suspend state to prevent touching disabled HW. After
fixing disable order in HDMI and moving TE handling to DECON it is
not needed anymore - all IRQ handlers and callbacks touching HW
are called only with enabled DECON.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The flag was used to trigger software update in TE IRQ handler only
if framebuffers were replaced. Since TE update is triggered always
when VBLANKs are enabled and after framebuffer replacement VBLANKs
are always enabled the flag becomes redundant.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The flag was used to check if IRQ handlers can touch HW. Since driver
enables IRQs only if hardware is enabled the flag becomes redundant.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since DECON uses enable_irq/disable_irq to full control IRQs,
there is no point in having flags to trace it separately.
As a bonus condition for software trigger becomes always true,
so it can be removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DECON is the only user of TE signal, moving all TE related
code to DECON driver allows to precise control of IRQ handlers.
This control allows to fix race between IRQ handler and DECON disable
code - now it is possible to disable DECON during IRQ handling
which can result in kernel crash. Beside race fixing this change
allows further code simplification.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
When vblanks are enabled userspace and/or kernel can expect vblank
interrupt at declared period of time. To generate vblank interrupt
image transfer must be triggered. This patch fixes vblank timeouts
in case of sw-trigger mode.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The output stage of the mixer uses YCbCr for the internal
computations, which is the reason that some registers take
YCbCr related data as input. In particular this applies
to MXR_BG_COLOR{0,1,2} and MXR_CM_COEFF_{Y,CB,CR}.
Document the formatting of the data which we write to
these registers.
While at it, unify wording of comments in the register header.
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DSIM uses MIC bridge which is between DECON and DSIM, so the driver
should expect bridge node on input side.
Fixes: 86418f9 ("drm: convert drivers to use of_graph_get_remote_node")
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Hardware require that MIXER(crtc) should be disabled prior to
HDMI(encoder). It was achieved by disabling crtc from encoder disable
callback, bypassing drm core. As a result drm core tried to call vblank
related routines on disabled crtc. The patch fixes it by simplifying
hdmi_disable routine - now it only cancels hotplug worker. Hardware will
be disabled in proper moment during pipe clock disable.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
There is no point in protecting only particular windows during update.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
BIT_IRQS_ENABLED flag duplicates drm_vblank_crtc::refcount, it could be
safely removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since fixing CMU code (drm/exynos/decon5433: fix CMU programming)
DECON started behave predictable and does not need special care
during DECON_UPDATE writes.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
All Exynos CRTCs are fully configured by .enable callback. The only users
of mode_set_nofb actually did nothing in their callbacks - they immediately
returned because devices were in suspend state - mode_set_nofb is always
called on disabled device.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since possible_crtcs are set by Exynos core helper pipe fields have no
raison d'etre. The only place it was used, as a hack, is
fimd_clear_channels, to avoid calling drm_crtc_handle_vblank, but DRM core
has already other protection mechanism (vblank->enabled), so it could be
safely removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
All Exynos planes are assigned to exactly one CRTC, it allows to simplify
initialization by moving setting of possible_crtcs to exynos_plane_init.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since crtc index is stored in drm_crtc pipe field became redundant.
The patch beside removing the field simplifies also
exynos_drm_crtc_get_pipe_from_type.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DECON in Exynos5433 has frame counter, it can be used to implement
get_vblank_counter callback.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
All Exynos CRTC drivers shouldn't fail at referencing vblank events,
alternate path is actually dead code.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
- Remove preclose hook of Exynos
. This was a exynos change of the patch series[1] merged already.
- Fix one dt broken issue
- Make sure to release bridge_node of Exynos MIPI-DSI driver.
[1] https://lists.freedesktop.org/archives/dri-devel/2017-March/135111.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=j5Vn
-----END PGP SIGNATURE-----
Merge tag 'exynos-drm-fixes-for-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into exynos-drm-next
- Fix a regression to description of exynos_drm_crtc
- Remove preclose hook of Exynos
. This was a exynos change of the patch series[1] merged already.
- Fix one dt broken issue
- Make sure to release bridge_node of Exynos MIPI-DSI driver.
[1] https://lists.freedesktop.org/archives/dri-devel/2017-March/135111.html
This patch removes unnecessary descriptions on
exynos_drm_crtc structure and adds one description
which specifies what pipe_clk member does.
pipe_clk support had been added by below patch without any description,
drm/exynos: add support for pipeline clock to the framework
Commit-id : f26b9343f5
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since bridge node is referenced during in the probe, it should be
released on removal.
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The dsi + panel is a parental relationship, so OF grpah is not needed.
Therefore, the current dsi_parse_dt function will throw an error,
because there is no linked OF graph for the case fimd + dsi + panel.
Parse the Pll burst and esc clock frequency properties in dsi_parse_dt()
and create a bridge_node only if there is an OF graph associated with dsi.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Again no apparent explanation for the split except hysterical raisins.
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Now that drm_[cm]alloc* helpers are simple one line wrappers around
kvmalloc_array and drm_free_large is just kvfree alias we can drop
them and replace by their native forms.
This shouldn't introduce any functional change.
Changes since v1
- fix typo in drivers/gpu//drm/etnaviv/etnaviv_gem.c - noticed by 0day
build robot
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Michal Hocko <mhocko@suse.com>drm: drop drm_[cm]alloc* helpers
[danvet: Fixup vgem which grew another user very recently.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517122312.GK18247@dhcp22.suse.cz
UAPI Changes:
- Return -ENODEV instead of -ENXIO when creating cma fb w/o valid gem (Daniel)
- Add aspect ratio and custom scaling propertis to connector state (Maarten)
Cross-subsystem Changes:
- None
Core Changes:
- Add Laurent as bridge reviewer and Andrzej as bridge maintainer (Archit)
- Maintain new STM driver through -misc (Yannick)
- Misc doc improvements (as is tradition) (Daniel)
- Add driver-private objects to atomic state (Dhinakaran)
- Deprecate preclose hook in modern drivers (use postclose) (Daniel)
- Add hwmode to vblank struct. This fixes mode access in irq context and reduced
a bunch of boilerplate (Daniel)
Driver Changes:
- vc4: Add out-fence support to vc4 V3D rendering (Eric)
- stm: Add stm32f429 display hw and am-480272h3tmqw-t01h panel support (Yannick)
- vc4: Remove 256MB cma limit from vc4 (Eric)
- dw-hdmi: Disable audio when inactive, instead of always enabled (Romain)
- zte: Add support for VGA to the ZTE driver (Shawn)
- i915: Track DP MST bandwidth and check it in atomic_check (Dhinakaran)
- vgem: Enable gem dmabuf import iface to facilitate ion testing (Laura)
- vc4: Add support for Cygnus (new dt compat string + couple bug fixes) (Eric)
- pl111: Add driver for pl111 CLCD display controller (Eric/Tom)
- vgem: Subclass drm_device instead of standalone platform device (Chris)
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Navare, Manasi D <manasi.d.navare@intel.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tom Cooksey <tom.cooksey@arm.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
* tag 'drm-misc-next-2017-05-16' of git://anongit.freedesktop.org/git/drm-misc: (72 commits)
drm: add missing declaration to drm_blend.h
drm/dp: Wait up all outstanding tx waiters
drm/dp: Read the tx msg state once after checking for an event
drm/prime: Forward declare struct device
drm/vblank: Lock down vblank->hwmode more
drm/vblank: drop the mode argument from drm_calc_vbltimestamp_from_scanoutpos
drm/vblank: Add FIXME comments about moving the vblank ts hooks
drm/vblank: Switch to bool in_vblank_irq in get_vblank_timestamp
drm/vblank: Switch drm_driver->get_vblank_timestamp to return a bool
drm/vgem: Convert to a struct drm_device subclass
gpu: drm: gma500: remove dead code
drm/sti: Adjust two checks for null pointers in sti_hqvdp_probe()
drm/sti: Fix typos in a comment line
drm/sti: Fix a typo in a comment line
drm/sti: Replace 17 seq_puts() calls by seq_putc()
drm/sti: Reduce function calls for sequence output at five places
drm/sti: use seq_puts to display a string
drm: Nerf the preclose callback for modern drivers
drm/exynos: Merge pre/postclose hooks
drm/tegra: switch to postclose
...
Again no apparent explanation for the split except hysterical raisins.
Merging them also makes it a bit more obviuos what's going on wrt the
runtime pm refdancing.
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170508082633.4214-3-daniel.vetter@ffwll.ch
-----BEGIN PGP SIGNATURE-----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=Snzj
-----END PGP SIGNATURE-----
Merge tag 'media/v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Media updates for v4.12-rc1:
- new driver to support mediatek jpeg in hardware codec
- rc-lirc, s5p-cec and st-cec staging drivers got promoted
- hardware histogram support for vsp1 driver
- added Virtual Media Controller driver, to make easier to test the
media controller
- added a new CEC driver (rainshadow-cec)
- removed two staging LIRC drivers for obscure hardware that are too
obsolete
- added support for Intel SR300 Depth camera
- some improvements at CEC and RC core
- lots of driver cleanups, improvements all over the tree
With this series, we're finally getting rid of the LIRC staging
driver. There's just one left (lirc_zilog), with require more care,
as part of its functionality (IR RX) is already provided by another
driver. Work in progress to convert it on the proper way"
* tag 'media/v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (304 commits)
[media] ov2640: print error if devm_*_optional*() fails
[media] atmel-isc: Fix the static checker warning
[media] ov2640: add support for MEDIA_BUS_FMT_YVYU8_2X8 and MEDIA_BUS_FMT_VYUY8_2X8
[media] ov2640: fix vflip control
[media] ov2640: fix duplicate width+height returning from ov2640_select_win()
[media] ov2640: add missing write to size change preamble
[media] ov2640: add information about DSP register 0xc7
[media] ov2640: improve banding filter register definitions/documentation
[media] ov2640: fix init sequence alignment
[media] ov2640: make GPIOLIB an optional dependency
[media] xc5000: fix spelling mistake: "calibration"
[media] vidioc-queryctrl.rst: fix menu/int menu references
[media] media-entity: only call dev_dbg_obj if mdev is not NULL
[media] pixfmt-meta-vsp1-hgo.rst: remove spurious '-'
[media] mtk-vcodec: avoid warnings because of empty macros
[media] coda: bump maximum number of internal framebuffers to 17
[media] media: mtk-vcodec: remove informative log
[media] subdev-formats.rst: remove spurious '-'
[media] dw2102: limit messages to buffer size
[media] ttusb2: limit messages to buffer size
...
Implement the CEC notifier support to allow CEC drivers to
be informed when there is a new physical address.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Similar to the previous commit, convert drivers open coding OF graph
parsing to use drm_of_find_panel_or_bridge instead.
This changes some error messages to debug messages (in the graph core).
Graph connections are often "no connects" depending on the particular
board, so we want to avoid spurious messages. Plus the kernel is not a
DT validator.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[seanpaul dropped rockchip changes since they're now obsolete]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Convert drivers to use the new of_graph_get_remote_node() helper
instead of parsing the endpoint node and then getting the remote device
node. Now drivers can just specify the device node and which
port/endpoint and get back the connected remote device node. The details
of the graph binding are nicely abstracted into the core OF graph code.
This changes some error messages to debug messages (in the graph core).
Graph connections are often "no connects" depending on the particular
board, so we want to avoid spurious messages. Plus the kernel is not a
DT validator.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Liviu Dudau <liviu.dudau@arm.com>
Tested-by: Eric Anholt <eric@anholt.net>
Tested-by: Jyri Sarha <jsarha@ti.com>
Tested by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJY2C9qAAoJEHm+PkMAQRiGaBQIAIGzdlZ6ImiP6zoukrRv7qUr
44ITm0lsBiL85QGedhQQL+Y9UqwUmlqgFqnH0Gr8YHNbLJWXzdjGbl5aVo4KjASq
104NLUDXtPww/xZdH4wJMzhuwucYwZOUyDOjOr0ak3cGxOE2xjNjHMZXxWUf20GO
EpRr6WhV1DUAvAdjdNa9KlcOjMluNpMLLyL1CFLjrkkArrWAyqOURKHAb6ZLghfv
iZV1qJTVPyYGpnlI3kuEgu2GuDjxqpoNLSr3wHyEHm/pBPEl7MX6zPbzcegBV8TY
cRRlXo4notdsuknmSNcj0hHuTQvw1kl7BhieLKVsnCyCIM6jjX4TSQZFutmbzwM=
=5iRl
-----END PGP SIGNATURE-----
Backmerge tag 'v4.11-rc4' into drm-next
Linux 4.11-rc4
The i915 GVT team need the rc4 code to base some more code on.
DSI forwards te-gpios interrupts to display controller, but if display
controller works in HW-TRIGGER mode this interrupt is not necessary.
Making te-gpios property optional allows to avoid generating spare
interrupts.
And also if panel device node of command mode panel device doesn't provide
te-gpios property then the panel driver failed to probe. This was a critial
issue.
With this patch we can not only get rid of 60 interrupt callbacks per second
but also fix the critial issues.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Printing raw kernel pointers might reveal information which sometimes we
try to hide (e.g. with Kernel Address Space Layout Randomization). Use
the "%pK" format so these pointers will be hidden for unprivileged
users.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch fixes copy/paste bug introduced during code refactoring.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: b93c2e8b5d ("drm/exynos/decon5433: configure sysreg in case of hardware trigger")Fixes:
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
VBLANK interrupt should be signalled as soon as scanout ends, front porch
is the best moment.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DECON in case of video mode generates interrupt by default at start
of vertical back porch. As this interrupt is used to generate VBLANK
events more optimal point is start of vertical front porch.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Current implementation of event handling assumes that vblank interrupt is
always called at the right time. It is not true, it can be delayed due to
various reasons. As a result different races can happen. The patch fixes
the issue by using hardware frame counter present in DECON to serialize
vblank and commit completion events.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
CRTC event is currently send with next vblank, or instantly in case crtc
is being disabled. This approach usually works, but in corner cases it can
result in premature event generation. Only device driver is able to verify
if the event can be sent. This patch is a first step in that direction - it
moves event handling to the drivers.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Support for Exynos4415 is going away because there are no internal nor
external users.
Since commit 46dcf0ff0d ("ARM: dts: exynos: Remove exynos4415.dtsi"),
the platform cannot be instantiated so remove also the drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kukjin Kim <kgene@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
"&" was obviously intended instead of "|". The original condition is
always true.
Fixes: b93c2e8b5d ("drm/exynos/decon5433: configure sysreg in case of hardware trigger")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
More drm-misc stuff for 4.12:
- drm_platform removal from Laurent
- more dw-hdmi bridge driver updates (Laurent, Kieran, Neil)
- more header cleanup and documentation
- more drm_debugs_remove_files removal (Noralf)
- minor qxl updates (Gerd)
- edp crc support in helper + analogix_dp (Tomeu) for more igt
testing!
- old/new iterator roll-out (Maarten)
- new bridge drivers: lvds (Laurent), megachips-something (Peter
Senna)
* tag 'drm-misc-next-2017-03-12' of git://anongit.freedesktop.org/git/drm-misc: (51 commits)
drm: bridge: dw-hdmi: Move the driver to a separate directory.
drm: bridge: dw-hdmi: Switch to regmap for register access
drm: bridge: dw-hdmi: Remove device type from platform data
drm: bridge: dw-hdmi: Add support for custom PHY configuration
drm: bridge: dw-hdmi: Create PHY operations
drm: bridge: dw-hdmi: Fix the PHY power up sequence
drm: bridge: dw-hdmi: Fix the PHY power down sequence
drm: bridge: dw-hdmi: Enable CSC even for DVI
drm: bridge: dw-hdmi: Move CSC configuration out of PHY code
drm: bridge: dw-hdmi: Remove unused functions
drm: Extract drm_file.h
drm: Remove DRM_MINOR_CNT
drm: rename drm_fops.c to drm_file.c
drm/doc: document fallback behaviour for atomic events
drm: Remove drmP.h include from drm_kms_helper_common.c
drm: Extract drm_pci.h
drm: Move drm_lock_data out of drmP.h
drm: Extract drm_prime.h
drm/doc: Add todo about connector_list_iter
drm/qxl: Remove qxl_debugfs_remove_files()
...
Merge Laurent's drm_platform removal code. Only conflict is with the
drm_pci.h extraction, which allows me to fix up the misplayed
drm_platform_init fumble that 0day and Stephen Rothwell reported.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
First slice of drm-misc-next for 4.12:
Core/subsystem-wide:
- link status core patch from Manasi, for signalling link train fail
to userspace. I also had the i915 patch in here, but that had a
small buglet in our CI, so reverted.
- more debugfs_remove removal from Noralf, almost there now (Noralf
said he'll try to follow up with the stragglers).
- drm todo moved into kerneldoc, for better visibility (see
Documentation/gpu/todo.rst), lots of starter tasks in there.
- devm_ of helpers + use it in sti (from Ben Gaignard, acked by Rob
Herring)
- extended framebuffer fbdev support (for fbdev flipping), and vblank
wait ioctl fbdev support (Maxime Ripard)
- misc small things all over, as usual
- add vblank callbacks to drm_crtc_funcs, plus make lots of good use
of this to simplify drivers (Shawn Guo)
- new atomic iterator macros to unconfuse old vs. new state
Small drivers:
- vc4 improvements from Eric
- vc4 kerneldocs (Eric)!
- tons of improvements for dw-mipi-dsi in rockchip from John Keeping
and Chris Zhong.
- MAINTAINERS entries for drivers managed in drm-misc. It's not yet
official, still an experiment, but definitely not complete fail and
better to avoid confusion. We kinda screwed that up with drm-misc a
bit when we started committers last year.
- qxl atomic conversion (Gabriel Krisman)
- bunch of virtual driver polish (qxl, virgl, ...)
- misc tiny patches all over
This is the first time we've done the same merge-window blackout for
drm-misc as we've done for drm-intel for ages, hence why we have a
_lot_ of stuff queued already. But it's still only half of drm-intel
(room to grow!), and the drivers in drm-misc experiment seems to work
at least insofar as that you also get lots of driver updates here
alredy.
* tag 'drm-misc-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-misc: (141 commits)
drm/vc4: Fix OOPSes from trying to cache a partially constructed BO.
drm/vc4: Fulfill user BO creation requests from the kernel BO cache.
Revert "drm/i915: Implement Link Rate fallback on Link training failure"
drm/fb-helper: implement ioctl FBIO_WAITFORVSYNC
drm: Update drm_fbdev_cma_init documentation
drm/rockchip/dsi: add dw-mipi power domain support
drm/rockchip/dsi: fix insufficient bandwidth of some panel
dt-bindings: add power domain node for dw-mipi-rockchip
drm/rockchip/dsi: remove mode_valid function
drm/rockchip/dsi: dw-mipi: correct the coding style
drm/rockchip/dsi: dw-mipi: support RK3399 mipi dsi
dt-bindings: add rk3399 support for dw-mipi-rockchip
drm/rockchip: dw-mipi-dsi: add reset control
drm/rockchip: dw-mipi-dsi: support non-burst modes
drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
drm/rockchip: vop: test for P{H,V}SYNC
drm/rockchip: dw-mipi-dsi: use positive check for N{H, V}SYNC
drm/rockchip: dw-mipi-dsi: use specific poll helper
drm/rockchip: dw-mipi-dsi: improve PLL configuration
drm/rockchip: dw-mipi-dsi: properly configure PHY timing
...
Backmerge the main pull request to sync up with all the newly landed
drivers. Otherwise we'll have chaos even before 4.12 started in
earnest.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
->fault(), ->page_mkwrite(), and ->pfn_mkwrite() calls do not need to
take a vma and vmf parameter when the vma already resides in vmf.
Remove the vma parameter to simplify things.
[arnd@arndb.de: fix ARM build]
Link: http://lkml.kernel.org/r/20170125223558.1451224-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/148521301778.19116.10840599906674778980.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The drm driver .load() operation is prone to race conditions as it
initializes the driver after registering the device nodes. Its usage is
deprecated, inline it in the probe function and call drm_dev_alloc() and
drm_dev_register() explicitly.
For consistency inline the .unload() handler in the remove function as
well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Summary:
- Add UHD support on TM2/TM2E boards.
. adding interlace mode support and 297MHz pixel clock support
for UHD mode, setting sysreg register in case of HW trigger mode,
and adding SiI8620 MHL bridge device support.
- Fix trigger mode issue on Rinato board.
. On Rinato board, HW trigger mode doesn't work so fix it.
- Some fixup and cleanup.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: fimd: Do not use HW trigger for exynos3250
drm/exynos/hdmi: add bridge support
drm/exynos/decon5433: signal vblank only on odd fields
drm/exynos/decon5433: add support for interlace modes
drm/exynos/hdmi: fix PLL for 27MHz settings
drm/exynos/hdmi: fix VSI infoframe registers
drm/exynos/hdmi: add 297MHz pixel clock support
drm/exynos: g2d: change platform driver name to 'exynos-drm-g2d'
drm/exynos/decon5433: configure sysreg in case of hardware trigger
The vblank hooks in struct drm_driver are deprecated and only meant for
legacy drivers. For modern drivers with DRIVER_MODESET flag, the hooks
in struct drm_crtc_funcs should be used instead.
As the result, exynos_drm_crtc_enable[disable]_vblank() become static
functions. They are moved around a bit to save forward declaration
though. Also while at it, we move one step further to kill
exynos_drm_crtc_from_pipe() completely by updating hdmi_bind() a bit.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-9-git-send-email-shawnguo@kernel.org
Core code already makes drm_driver.get_vblank_counter hook optional by
letting drm_vblank_no_hw_counter be the default implementation for the
function hook. So the drm_vblank_no_hw_counter assignment in the driver
code becomes redundant and can be removed now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-3-git-send-email-shawnguo@kernel.org
Noticed that everyone duplicates the same logic here and we could safe
a few lines per driver. Yay for lots of drivers to make such tiny
refactors worth-while!
v2: Forgot to git add everything :(
v3: Actually remove release_fbi (Sean, Emil, Chris) ...
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207161603.17611-1-daniel.vetter@ffwll.ch
Commit a6f75aa161 ("drm/exynos: fimd: add HW trigger support") added
hardware trigger support to the FIMD controller driver. I have tested
but this broke the display in at least the exynos3250 Gear 2. So until
the issue is fixed, avoid using HW trigger for the exynos3250 based
boards and use SW trigger as it was before the mentioned commit.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
On TM2/TM2e platforms HDMI output is connected to MHL bridge
SiI8620. To allow configure UltraHD modes on the bridge
and to eliminate unsupported modes this bridge should be
attached to drm_encoder implemented in exynos_hdmi.
Changelog v1:
- fix drm_attach_bridge argument.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
In case of interlace mode irq is generated for odd and even fields, but
vblank should be signaled only for the last emitted field.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Some registers should be programmed differently in interlace mode.
Additionally IP does not signal stop state properly in interlaced
mode, so warning has been removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Current settings for 27MHz and 27.027MHz do not work. Use the settings from
vendor code instead.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
VSI infoframe registers address space is non-contiguous, so infoframe write
should be split into two chunks.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The current name is 's5p-g2d', which is identical with the driver
name of the old V4L2 driver in media/platform.
This is probably due to the DRM driver being based on the V4L2
driver when it was initially created. Still the clashing of driver
names is confusing, so rename it to something in line with the
other DRM subdrivers.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
In case of HW trigger mode, sysreg register should be configured to
enable TE functionality. The patch refactors also trigger setup function.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Instead of receiving the num_crts as a parameter, we can read it
directly from the mode_config structure. I audited the drivers that
invoke this helper and I believe all of them initialize the mode_config
struct accordingly, prior to calling the fb_helper.
I used the following coccinelle hack to make this transformation, except
for the function headers and comment updates. The first and second
rules are split because I couldn't find a way to remove the unused
temporary variables at the same time I removed the parameter.
// <smpl>
@r@
expression A,B,D,E;
identifier C;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
expression A,B,C,D,E;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
identifier r.C;
type T;
expression V;
@@
- T C;
<...
when != C
- C = V;
...>
// </smpl>
Changes since v1:
- Rebased on top of the tip of drm-misc-next.
- Remove mention to sti since a proper fix got merged.
Suggested-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202162640.27261-1-krisman@collabora.co.uk
adding runtime PM support to MIC driver, and including some
cleanups - especially using atomic helper functions
instead of specific ones - and fixups.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: g2d: prevent integer overflow in
drm/exynos: fix a timeout loop
drm/exynos: use atomic helper commit
drm/exynos: remove unnecessary codes
drm/exynos: mic: Add runtime PM support
drm/exynos: Stop using drm_framebuffer_unregister_private
drm/exynos: mic: Fix parse_dt function
drm/exynos: mic: Add mode_set callback function
Another round of -misc stuff:
- Noralf debugfs cleanup cleanup (not yet everything, some more driver
patches awaiting acks).
- More doc work.
- edid/infoframe fixes from Ville.
- misc 1-patch fixes all over, as usual
Noralf needs this for his tinydrm pull request.
* tag 'drm-misc-next-2017-01-30' of git://anongit.freedesktop.org/git/drm-misc: (48 commits)
drm/vc4: Remove vc4_debugfs_cleanup()
dma/fence: Export enable-signaling tracepoint for emission by drivers
drm/tilcdc: Remove tilcdc_debugfs_cleanup()
drm/tegra: Remove tegra_debugfs_cleanup()
drm/sti: Remove drm_debugfs_remove_files() calls
drm/radeon: Remove drm_debugfs_remove_files() call
drm/omap: Remove omap_debugfs_cleanup()
drm/hdlcd: Remove hdlcd_debugfs_cleanup()
drm/etnaviv: Remove etnaviv_debugfs_cleanup()
drm/etnaviv: allow build with COMPILE_TEST
drm/amd/amdgpu: Remove drm_debugfs_remove_files() call
drm/prime: Clarify DMA-BUF/GEM Object lifetime
drm/ttm: Make sure BOs being swapped out are cacheable
drm/atomic: Remove drm_atomic_debugfs_cleanup()
drm: drm_minor_register(): Clean up debugfs on failure
drm: debugfs: Remove all files automatically on cleanup
drm/fourcc: add vivante tiled layout format modifiers
drm/edid: Set YQ bits in the AVI infoframe according to CEA-861-F
drm/edid: Set AVI infoframe Q even when QS=0
drm/edid: Introduce drm_hdmi_avi_infoframe_quant_range()
...
The size computations done in the ioctl function use an integer.
If userspace submits a request with req->cmd_nr or req->cmd_buf_nr
set to INT_MAX, the integer computations overflow later, leading
to potential (kernel) memory corruption.
Prevent this issue by enforcing a limit on the number of submitted
commands, so that we have enough headroom later for the size
computations.
Note that this change has no impact on the currently available
users in userspace, like e.g. libdrm/exynos.
While at it, also make a comment about the size computation more
detailed.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
We were trying to print an error message if we timed out here, but the
loop actually ends with "tries" set to UINT_MAX and not zero. Fix this
by changing from tries-- to --tries.
A for loop would actually be the most natural way to do this. My fix
means we only loop 99 times instead of 100 but that's probably ok.
Fixes: a696394c52 ('drm/exynos: mixer: simplify loop in vp_win_reset()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch replaces specific atomic commit function
with atomic helper commit one.
For this, it removes existing atomic commit function
and relevant code specific to Exynos DRM and makes
atomic helper commit to be used instead.
Below are changes for the use of atomic helper commit:
- add atomic_commit_tail callback specific to Exynos DRM
. default implemention of atomic helper doesn't mesh well
with runtime PM so the device driver which supports runtime
PM should call drm_atomic_helper_commit_modeset_enables function
prior to drm_atomic_helper_commit_planes function call.
atomic_commit_tail callback implements this call ordering.
- allow plane commit only in case that CRTC device is enabled.
. for this, it calls atomic_helper_commit_planes function
with DRM_PLANE_COMMIT_ACTIVE_ONLY flag in atomic_commit_tail callback.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.com>
This patch removes exynos_drm_crtc_cancel_page_flip call
when drm is closed because at that time, events will be released
by drm_events_release function.
Changelog v1:
- remove exynos_drm_crtc_cancel_page_flip function also because
this funtion isn't used anymore.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
This patch adds runtime support calls to notify device core when MIC
device is really in use. Runtime PM is implemented by enabling and
disabling clocks like in other Exynos DRM subdrivers. Adding runtime
PM support is needed to let power domain with this device to be turned
off when display is not used.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This is the deprecated function for when you embedded the framebuffer
somewhere else (which breaks refcounting). But exynos is using
drm_framebuffer_remove and a free-standing fb, so this is rendundant.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The OF graph is not necessary because the panel is a child of
dsi. therefore, the parse_dt function of dsi does not need to
check the remote_node connected to the panel. and the whole
parse_dt function should be refactored later.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Before applying the patch, used the of_get_videomode function to
parse the display-timings in the panel which is the child driver
of dsi in the devicetree. this is wrong. So removed the
of_get_videomode and fixed to get videomode struct through
mode_set callback function.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
- cleanups&fixes for dw-hdmi bride driver (Laurent)
- updates for adv bridge driver (John Stultz) for nexus
- drm_crtc_from_index helper rollout (Shawn Guo)
- removing drm_framebuffer_unregister_private from drivers&core
- target_vblank (Andrey Grodzovsky)
- misc tiny stuff
* tag 'drm-misc-next-2017-01-23' of git://anongit.freedesktop.org/git/drm-misc: (49 commits)
drm: qxl: Open code teardown function for qxl
drm: qxl: Open code probing sequence for qxl
drm/bridge: adv7511: Re-write the i2c address before EDID probing
drm/bridge: adv7511: Reuse __adv7511_power_on/off() when probing EDID
drm/bridge: adv7511: Rework adv7511_power_on/off() so they can be reused internally
drm/bridge: adv7511: Enable HPD interrupts to support hotplug and improve monitor detection
drm/bridge: adv7511: Switch to using drm_kms_helper_hotplug_event()
drm/bridge: adv7511: Use work_struct to defer hotplug handing to out of irq context
drm: vc4: use crtc helper drm_crtc_from_index()
drm: tegra: use crtc helper drm_crtc_from_index()
drm: nouveau: use crtc helper drm_crtc_from_index()
drm: mediatek: use crtc helper drm_crtc_from_index()
drm: kirin: use crtc helper drm_crtc_from_index()
drm: exynos: use crtc helper drm_crtc_from_index()
dt-bindings: display: dw-hdmi: Clean up DT bindings documentation
drm: bridge: dw-hdmi: Assert SVSRET before resetting the PHY
drm: bridge: dw-hdmi: Fix the name of the PHY reset macros
drm: bridge: dw-hdmi: Define and use macros for PHY register addresses
drm: bridge: dw-hdmi: Detect PHY type at runtime
drm: bridge: dw-hdmi: Handle overflow workaround based on device version
...
Backmerge Linus master to get the connector locking revert.
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux: (645 commits)
sysctl: fix proc_doulongvec_ms_jiffies_minmax()
Revert "drm/probe-helpers: Drop locking from poll_enable"
MAINTAINERS: add Dan Streetman to zbud maintainers
MAINTAINERS: add Dan Streetman to zswap maintainers
mm: do not export ioremap_page_range symbol for external module
mn10300: fix build error of missing fpu_save()
romfs: use different way to generate fsid for BLOCK or MTD
frv: add missing atomic64 operations
mm, page_alloc: fix premature OOM when racing with cpuset mems update
mm, page_alloc: move cpuset seqcount checking to slowpath
mm, page_alloc: fix fast-path race with cpuset update or removal
mm, page_alloc: fix check for NULL preferred_zone
kernel/panic.c: add missing \n
fbdev: color map copying bounds checking
frv: add atomic64_add_unless()
mm/mempolicy.c: do not put mempolicy before using its nodemask
radix-tree: fix private list warnings
Documentation/filesystems/proc.txt: add VmPin
mm, memcg: do not retry precharge charges
proc: add a schedule point in proc_pid_readdir()
...
DECON_TV requires STANDALONE_UPDATE after output enabling, otherwise it does
not start. This change is neutral for DECON.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DECON_CMU register has reserved bits which should not be zeroed, otherwise
IP can behave strangely and cause IOMMU faults.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
decon_commit is called just after reset so video is disabled anyway.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
STANDALONE_UPDATE_F should be set if something changed in plane configurations,
including plane disable.
The patch fixes page-faults bugs, caused by decon still using framebuffers
of disabled planes.
v2: fixed clear-bit code (Thx Marek)
v3: use test_and_clear_bit (Thx Joonyoung)
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Improper usage of DECON_UPDATE register leads to subtle errors.
If it set in decon_commit when there are no active windows it results
in slow registry updates - all subsequent shadow registry updates takes more
than full vblank. On the other side if it is not set when there are
active windows it results in garbage on the screen after suspend/resume of
FB console.
The patch hopefully fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Declare exynos_drm_crtc_ops structures as const as they are only passed
as an argument to the function exynos_drm_crtc_create. This argument is
of type const struct exynos_drm_crtc_ops *, so exynos_drm_crtc_ops
structures having this property can be declared const.
Done using Coccinelle:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct exynos_drm_crtc_ops i@p={...};
@ok@
position p;
identifier r.i;
@@
exynos_drm_crtc_create(...,&i@p,...)
@bad@
position p!={r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
+const
struct exynos_drm_crtc_ops i;
File size before:
text data bss dec hex filename
5008 280 0 5288 14a8 exynos/exynos5433_drm_decon.o
File size after:
text data bss dec hex filename
5120 176 0 5296 14b0 exynos/exynos5433_drm_decon.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1483984493-25284-1-git-send-email-bhumirks@gmail.com
Back to regular -misc pulls with reasonable sizes:
- dma_fence error clarification (Chris)
- drm_crtc_from_index helper (Shawn), pile more patches on the m-l to roll
this out to drivers
- mmu-less support for fbdev helpers from Benjamin
- piles of kerneldoc work
- some polish for crc support from Tomeu and Benjamin
- odd misc stuff all over
* tag 'drm-misc-next-2017-01-09' of git://anongit.freedesktop.org/git/drm-misc: (48 commits)
dma-fence: Introduce drm_fence_set_error() helper
dma-fence: Wrap querying the fence->status
dma-fence: Clear fence->status during dma_fence_init()
drm: fix compilations issues introduced by "drm: allow to use mmuless SoC"
drm: Change the return type of the unload hook to void
drm: add more document for drm_crtc_from_index()
drm: remove useless parameters from drm_pick_cmdline_mode function
drm: crc: Call wake_up_interruptible() each time there is a new CRC entry
drm: allow to use mmuless SoC
drm: compile drm_vm.c only when needed
fbmem: add a default get_fb_unmapped_area function
drm: crc: Wait for a frame before returning from open()
drm: Move locking into drm_debugfs_crtc_crc_add
drm/imx: imx-tve: Remove unused variable
Revert "drm: nouveau: fix build when LEDS_CLASS=m"
drm: Add kernel-doc for drm_crtc_commit_get/put
drm/atomic: Fix outdated comment.
drm: reference count event->completion
gpu: drm: mgag200: mgag200_main:- Handle error from pci_iomap
drm: Document deprecated load/unload hook
...
The integer returned by the unload hook is ignored by the drm core, so
let's make it void.
This patch was created using the following Coccinelle semantic script
(except for the declaration and comment in drm_drv.h):
Compile-tested only.
// <smpl>
@ get_name @
struct drm_driver drv;
identifier fn;
@@
drv.unload = fn;
@ replace_type @
identifier get_name.fn;
@@
- int
+ void
fn (...)
{
...
}
@ remove_return_param @
identifier get_name.fn;
@@
void fn (...)
{
<...
if (...)
return
- ...
;
...>
}
@ drop_final_return @
identifier get_name.fn;
@@
void fn (...)
{
...
- return 0;
}
// </smpl>
Suggested-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Acked-by: Christian König <christian.koenig@amd.com>.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170106175731.29196-1-krisman@collabora.co.uk
First -misc pull for 4.11:
- drm_mm rework + lots of selftests (Chris Wilson)
- new connector_list locking+iterators
- plenty of kerneldoc updates
- format handling rework from Ville
- atomic helper changes from Maarten for better plane corner-case handling
in drivers, plus the i915 legacy cursor patch that needs this
- bridge cleanup from Laurent
- plus plenty of small stuff all over
- also contains a merge of the 4.10 docs tree so that we could apply the
dma-buf kerneldoc patches
It's a lot more than usual, but due to the merge window blackout it also
covers about 4 weeks, so all in line again on a per-week basis. The more
annoying part with no pull request for 4 weeks is managing cross-tree
work. The -intel pull request I'll follow up with does conflict quite a
bit with -misc here. Longer-term (if drm-misc keeps growing) a
drm-next-queued to accept pull request for the next merge window during
this time might be useful.
I'd also like to backmerge -rc2+this into drm-intel next week, we have
quite a pile of patches waiting for the stuff in here.
* tag 'drm-misc-next-2016-12-30' of git://anongit.freedesktop.org/git/drm-misc: (126 commits)
drm: Add kerneldoc markup for new @scan parameters in drm_mm
drm/mm: Document locking rules
drm: Use drm_mm_insert_node_in_range_generic() for everyone
drm: Apply range restriction after color adjustment when allocation
drm: Wrap drm_mm_node.hole_follows
drm: Apply tight eviction scanning to color_adjust
drm: Simplify drm_mm scan-list manipulation
drm: Optimise power-of-two alignments in drm_mm_scan_add_block()
drm: Compute tight evictions for drm_mm_scan
drm: Fix application of color vs range restriction when scanning drm_mm
drm: Unconditionally do the range check in drm_mm_scan_add_block()
drm: Rename prev_node to hole in drm_mm_scan_add_block()
drm: Fix O= out-of-tree builds for selftests
drm: Extract struct drm_mm_scan from struct drm_mm
drm: Add asserts to catch overflow in drm_mm_init() and drm_mm_init_scan()
drm: Simplify drm_mm_clean()
drm: Detect overflow in drm_mm_reserve_node()
drm: Fix kerneldoc for drm_mm_scan_remove_block()
drm: Promote drm_mm alignment to u64
drm: kselftest for drm_mm and restricted color eviction
...
Instead of linking encoders and bridges in every driver (and getting it
wrong half of the time, as many drivers forget to set the drm_bridge
encoder pointer), do so in core code. The drm_bridge_attach() function
needs the encoder and optional previous bridge to perform that task,
update all the callers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Stefan Agner <stefan@agner.ch> # For DCU
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # For atmel-hlcdc
Acked-by: Vincent Abriou <vincent.abriou@st.com> # For STI
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # For sun4i
Acked-by: Xinliang Liu <z.liuxinliang@hisilicon.com> # For hisilicon
Acked-by: Jyri Sarha <jsarha@ti.com> # For tilcdc
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481709550-29226-4-git-send-email-laurent.pinchart+renesas@ideasonboard.com
Every single user of vmf->virtual_address typed that entry to unsigned
long before doing anything with it so the type of virtual_address does
not really provide us any additional safety. Just use masked
vmf->address which already has the appropriate type.
Link: http://lkml.kernel.org/r/1479460644-25076-3-git-send-email-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit aeefb36832 ("drm/exynos: gsc: add device tree support and remove
usage of static mappings") made the DRM_EXYNOS_GSC Kconfig symbol to only
be selectable if the exynos-gsc V4L2 driver isn't enabled, since both use
the same HW IP block.
But added the dependency as depends on !VIDEO_SAMSUNG_EXYNOS_GSC which is
not correct since Kconfig expressions are not boolean but tristate. So it
will only evaluate to 'n' if VIDEO_SAMSUNG_EXYNOS_GSC=y but will evaluate
to 'm' if VIDEO_SAMSUNG_EXYNOS_GSC=m.
This means that both the V4L2 and DRM drivers can be enabled if the former
is enabled as a module, which isn't what we want since otherwise 2 drivers
could attempt to use the hardware at the same time.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Trivial fixes to spelling mistakes "precalser" to "prescaler"
in dev_err messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Fix exynos_drm_gem_create() error messages to include flags and size when
flags and size are invalid.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Use core helpers to generate infoframes and generate vendor frame if necessary.
Changelog:
- changed 'ret >= 0' checks to '!ret'
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYRIGyAAoJEHm+PkMAQRiG2ksH/jwMUT9j6glbwESxbn1YTqTM
QcBT5AMc7D0wNuidQe0hWZMtG4RbC+4ZhxzZl2wPgA2gueJ+rBnyX7bgtA7ka8ka
Fdc3u/Q1v38HPzf8iBnxcdCs40VgsoMLjFYCXrpOxuGDNKYzRd+Q8aI2TeGvzbyi
X8+6oAWifBwo2oA06jfcuUncEWbyDDyK9aQksmfKOpjHdb26yELPEhsPOlds1g7E
jYLnvUVnU2CoFaumta+rZQ0kzLdc4Ntu0wEao6WzJuQKsgoID+tS/6iudi8cUhDp
YowGAVoOfr6rAJB0mwrDVfugpamaT3386XKyocdNsK0/jR60UIJ8x+WzvvSU+lY=
=JTBj
-----END PGP SIGNATURE-----
Backmerge tag 'v4.9-rc8' into drm-next
Linux 4.9-rc8
Daniel requested this so we could apply some follow on fixes cleanly to -next.
Free memory mapping, if hdmi_probe is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- better atomic state debugging from Rob
- fence prep from gustavo
- sumits flushed out his backlog of pending dma-buf/fence patches from
various people
- drm_mm leak debugging plus trying to appease Kconfig (Chris)
- a few misc things all over
* tag 'topic/drm-misc-2016-11-10' of git://anongit.freedesktop.org/drm-intel: (35 commits)
drm: Make DRM_DEBUG_MM depend on STACKTRACE_SUPPORT
drm/i915: Restrict DRM_DEBUG_MM automatic selection
drm: Restrict stackdepot usage to builtin drm.ko
drm/msm: module param to dump state on error irq
drm/msm/mdp5: add atomic_print_state support
drm/atomic: add debugfs file to dump out atomic state
drm/atomic: add new drm_debug bit to dump atomic state
drm: add helpers to go from plane state to drm_rect
drm: add helper for printing to log or seq_file
drm: helper macros to print composite types
reservation: revert "wait only with non-zero timeout specified (v3)" v2
drm/ttm: fix ttm_bo_wait
dma-buf/fence: revert "don't wait when specified timeout is zero" (v2)
dma-buf/fence: make timeout handling in fence_default_wait consistent (v2)
drm/amdgpu: add the interface of waiting multiple fences (v4)
dma-buf: return index of the first signaled fence (v2)
MAINTAINERS: update Sync File Framework files
dma-buf/sw_sync: put fence reference from the fence creation
dma-buf/sw_sync: mark sync_timeline_create() static
drm: Add stackdepot include for DRM_DEBUG_MM
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYHmoCAAoJEHm+PkMAQRiG7RMIAI2i7Y5hpL5yCxK5AFaL4u/G
KxXfp1B1UanUTgjOmd7zGqtDYcFX9t7GTTUFixQ7/9Opr4PD9qbnatoDGSc3xjbT
msDgA1B78F1/Q3kHWfeGq32MihQ4mj5NwUCo+igUcUvvWG7mHgzErj/Nh5RoobQX
p/izdpTbrw3GX6xXB8olbG7XWHaVye/+TT3q6+gmgm8I/QEujcLeGoycE0zlhPN8
FG/JX76At/+ZM2Py7Oxo3k+oKL9CHrtOQYDp/wN0uslV5eYvvkZz0/M1HMOGZt+c
gZU5jzM17K7C4Nzo06WAuBU9wUBGc25m+cPicLlOmljnzfU+f50SKaDjZq3p7QI=
=2KUF
-----END PGP SIGNATURE-----
Backmerge tag 'v4.9-rc4' into drm-next
Linux 4.9-rc4
This is needed for nouveau development.
We don't want all planes to be added to the state whenever a
plane with fixed zpos gets enabled/disabled. This is true
especially for eg. cursor planes on i915, as we want cursor
updates to go through w/o throttling. Same holds for drivers
that don't support zpos at all (i915 actually falls into this
category right now since we've not yet added zpos support).
Allow drivers more freedom by letting them deal with zpos
themselves instead of doing it in drm_atomic_helper_check_planes()
unconditionally. Let's just inline the required calls into all
the driver that currently depend on this.
v2: Inline the stuff into the drivers instead of adding another
helper, document things better (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lyude <cpaul@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: stable@vger.kernel.org
Fixes: 44d1240d00 ("drm: add generic zpos property")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1476111056-12734-1-git-send-email-ville.syrjala@linux.intel.com
First -misc pull for 4.10:
- drm_format rework from Laurent
- reservation patches from Chris that missed 4.9.
- aspect ratio support in infoframe helpers and drm mode/edid code
(Shashank Sharma)
- rotation rework from Ville (first parts at least)
- another attempt at the CRC debugfs interface from Tomeu
- piles and piles of misc patches all over
* tag 'topic/drm-misc-2016-10-24' of git://anongit.freedesktop.org/drm-intel: (55 commits)
drm: Use u64 for intermediate dotclock calculations
drm/i915: Use the per-plane rotation property
drm/omap: Use per-plane rotation property
drm/omap: Set rotation property initial value to BIT(DRM_ROTATE_0) insted of 0
drm/atmel-hlcdc: Use per-plane rotation property
drm/arm: Use per-plane rotation property
drm: Add support for optional per-plane rotation property
drm/atomic: Reject attempts to use multiple rotation angles at once
drm: Add drm_rotation_90_or_270()
dma-buf/sync_file: hold reference to fence when creating sync_file
drm/virtio: kconfig: Fixup white space.
drm/fence: release fence reference when canceling event
drm/i915: Handle early failure during intel_get_load_detect_pipe
drm/fb_cma_helper: do not free fbdev if there is none
drm: fix sparse warnings on undeclared symbols in crc debugfs
gpu: Remove depends on RESET_CONTROLLER when not a provider
i915: don't call drm_atomic_state_put on invalid pointer
drm: Don't export the drm_fb_get_bpp_depth() function
drm/arm: mali-dp: Replace drm_fb_get_bpp_depth() with drm_format_plane_cpp()
drm: vmwgfx: Replace drm_fb_get_bpp_depth() with drm_format_info()
...
This removes the 'write' and 'force' from get_vaddr_frames() and
replaces them with 'gup_flags' to make the use of FOLL_FORCE explicit in
callers as use of this flag can result in surprising behaviour (and
hence bugs) within the mm subsystem.
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drm_atomic_state has a complicated single owner model that tracks the
single reference from allocation through to destruction on another
thread - or perhaps on a local error path. We can simplify this tracking
by using reference counting (at a cost of a few more atomics). This is
even more beneficial when the lifetime of the state becomes more
convoluted than being passed to a single worker thread for the commit.
v2: Double check !intel atomic_commit functions for missing gets
v3: Update kerneldocs
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161014121833.439-27-chris@chris-wilson.co.uk
Pull drm updates from Dave Airlie:
"Core:
- Fence destaging work
- DRIVER_LEGACY to split off legacy drm drivers
- drm_mm refactoring
- Splitting drm_crtc.c into chunks and documenting better
- Display info fixes
- rbtree support for prime buffer lookup
- Simple VGA DAC driver
Panel:
- Add Nexus 7 panel
- More simple panels
i915:
- Refactoring GEM naming
- Refactored vma/active tracking
- Lockless request lookups
- Better stolen memory support
- FBC fixes
- SKL watermark fixes
- VGPU improvements
- dma-buf fencing support
- Better DP dongle support
amdgpu:
- Powerplay for Iceland asics
- Improved GPU reset support
- UVD/VEC powergating support for CZ/ST
- Preinitialised VRAM buffer support
- Virtual display support
- Initial SI support
- GTT rework
- PCI shutdown callback support
- HPD IRQ storm fixes
amdkfd:
- bugfixes
tilcdc:
- Atomic modesetting support
mediatek:
- AAL + GAMMA engine support
- Hook up gamma LUT
- Temporal dithering support
imx:
- Pixel clock from devicetree
- drm bridge support for LVDS bridges
- active plane reconfiguration
- VDIC deinterlacer support
- Frame synchronisation unit support
- Color space conversion support
analogix:
- PSR support
- Better panel on/off support
rockchip:
- rk3399 vop/crtc support
- PSR support
vc4:
- Interlaced vblank timing
- 3D rendering CPU overhead reduction
- HDMI output fixes
tda998x:
- HDMI audio ASoC support
sunxi:
- Allwinner A33 support
- better TCON support
msm:
- DT binding cleanups
- Explicit fence-fd support
sti:
- remove sti415/416 support
etnaviv:
- MMUv2 refactoring
- GC3000 support
exynos:
- Refactoring HDMI DCC/PHY
- G2D pm regression fix
- Page fault issues with wait for vblank
There is no nouveau work in this tree, as Ben didn't get a pull
request in, and he was fighting moving to atomic and adding mst
support, so maybe best it waits for a cycle"
* tag 'drm-for-v4.9' of git://people.freedesktop.org/~airlied/linux: (1412 commits)
drm/crtc: constify drm_crtc_index parameter
drm/i915: Fix conflict resolution from backmerge of v4.8-rc8 to drm-next
drm/i915/guc: Unwind GuC workqueue reservation if request construction fails
drm/i915: Reset the breadcrumbs IRQ more carefully
drm/i915: Force relocations via cpu if we run out of idle aperture
drm/i915: Distinguish last emitted request from last submitted request
drm/i915: Allow DP to work w/o EDID
drm/i915: Move long hpd handling into the hotplug work
drm/i915/execlists: Reinitialise context image after GPU hang
drm/i915: Use correct index for backtracking HUNG semaphores
drm/i915: Unalias obj->phys_handle and obj->userptr
drm/i915: Just clear the mmiodebug before a register access
drm/i915/gen9: only add the planes actually affected by ddb changes
drm/i915: Allow PCH DPLL sharing regardless of DPLL_SDVO_HIGH_SPEED
drm/i915/bxt: Fix HDMI DPLL configuration
drm/i915/gen9: fix the watermark res_blocks value
drm/i915/gen9: fix plane_blocks_per_line on watermarks calculations
drm/i915/gen9: minimum scanlines for Y tile is not always 4
drm/i915/gen9: fix the WaWmMemoryReadLatency implementation
drm/i915/kbl: KBL also needs to run the SAGV code
...
-----BEGIN PGP SIGNATURE-----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=JqCR
-----END PGP SIGNATURE-----
Merge tag 'media/v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation improvements: conversion of all non-DocBook documents
to Sphinx and lots of fixes to the uAPI media book
- New PCI driver for Techwell TW5864 media grabber boards
- New SoC driver for ATMEL Image Sensor Controller
- Removal of some obsolete SoC drivers (s5p-tv driver and soc_camera
drivers)
- Addition of ST CEC driver
- Lots of drivers fixes, improvements and additions
* tag 'media/v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (464 commits)
[media] ttusb_dec: avoid the risk of go past buffer
[media] cx23885: Fix some smatch warnings
[media] si2165: switch to regmap
[media] si2165: use i2c_client->dev instead of i2c_adapter->dev for logging
[media] si2165: Remove legacy attach
[media] cx231xx: attach si2165 driver via i2c_client
[media] cx231xx: Prepare for attaching new style i2c_client DVB demod drivers
[media] cx23885: attach si2165 driver via i2c_client
[media] si2165: support i2c_client attach
[media] si2165: avoid division by zero
[media] rcar-vin: add R-Car gen2 fallback compatibility string
[media] lgdt3306a: remove 20*50 msec unnecessary timeout
[media] cx25821: Remove deprecated create_singlethread_workqueue
[media] cx25821: Drop Freeing of Workqueue
[media] cxd2841er: force 8MHz bandwidth for DVB-C if specified bw not supported
[media] redrat3: hardware-specific parameters
[media] redrat3: remove hw_timeout member
[media] cxd2841er: BER and SNR reading for ISDB-T
[media] dvb-usb: avoid link error with dib3000m{b,c|
[media] dvb-usb: split out common parts of dibusb
...
Including:
* Support for interrupt virtualization in the AMD IOMMU driver.
These patches were shared with the KVM tree and are already
merged through that tree.
* Generic DT-binding support for the ARM-SMMU driver. With this
the driver now makes use of the generic DMA-API code. This
also required some changes outside of the IOMMU code, but
these are acked by the respective maintainers.
* More cleanups and fixes all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1hFE
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- support for interrupt virtualization in the AMD IOMMU driver. These
patches were shared with the KVM tree and are already merged through
that tree.
- generic DT-binding support for the ARM-SMMU driver. With this the
driver now makes use of the generic DMA-API code. This also required
some changes outside of the IOMMU code, but these are acked by the
respective maintainers.
- more cleanups and fixes all over the place.
* tag 'iommu-updates-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (40 commits)
iommu/amd: No need to wait iommu completion if no dte irq entry change
iommu/amd: Free domain id when free a domain of struct dma_ops_domain
iommu/amd: Use standard bitmap operation to set bitmap
iommu/amd: Clean up the cmpxchg64 invocation
iommu/io-pgtable-arm: Check for v7s-incapable systems
iommu/dma: Avoid PCI host bridge windows
iommu/dma: Add support for mapping MSIs
iommu/arm-smmu: Set domain geometry
iommu/arm-smmu: Wire up generic configuration support
Docs: dt: document ARM SMMU generic binding usage
iommu/arm-smmu: Convert to iommu_fwspec
iommu/arm-smmu: Intelligent SMR allocation
iommu/arm-smmu: Add a stream map entry iterator
iommu/arm-smmu: Streamline SMMU data lookups
iommu/arm-smmu: Refactor mmu-masters handling
iommu/arm-smmu: Keep track of S2CR state
iommu/arm-smmu: Consolidate stream map entry state
iommu/arm-smmu: Handle stream IDs more dynamically
iommu/arm-smmu: Set PRIVCFG in stage 1 STEs
iommu/arm-smmu: Support non-PCI devices with SMMUv3
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX8Zc4AAoJEHm+PkMAQRiGQG8H/2Hd4IwJh75snGY5LAiWt6ra
kGM/SobvLAMtcoxXCeHqf2bZrxa2Zz9tnEzhuLMGaf9a3l79xHa8YumK5KS1JPGV
6lZBvuPi8BIyT0cpYH000e5ehHfhP6pSGJKZ2EuLv43HcBeVZEGAf3/8jSAlNA15
bwFy2ZEkwJGThbnT6au0Y3s9h8LcNjtllu9hjfb+/9oNGvp8r4QhdVodIqIQ4cv6
SeUfv7Pn2LZDMCSaTP9bh2KaR4dwYZHFsVe75x2wND5Sfq7DVBBfFkAoV/RwJDTM
gBc3PNnmzb/tix6ohOrSQnSiGsXv1uASxvHH3RD2zG6g7Aj9Eq/+Z7ZdPu2+o+U=
=U+ef
-----END PGP SIGNATURE-----
Merge tag 'v4.8' into patchwork
Linux 4.8
* tag 'v4.8': (1761 commits)
Linux 4.8
ARM: 8618/1: decompressor: reset ttbcr fields to use TTBR0 on ARMv7
MIPS: CM: Fix mips_cm_max_vp_width for non-MT kernels on MT systems
include/linux/property.h: fix typo/compile error
ocfs2: fix deadlock on mmapped page in ocfs2_write_begin_nolock()
mm: workingset: fix crash in shadow node shrinker caused by replace_page_cache_page()
MAINTAINERS: Switch to kernel.org email address for Javi Merino
x86/entry/64: Fix context tracking state warning when load_gs_index fails
x86/boot: Initialize FPU and X86_FEATURE_ALWAYS even if we don't have CPUID
x86/vdso: Fix building on big endian host
x86/boot: Fix another __read_cr4() case on 486
sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock
sctp: change to check peer prsctp_capable when using prsctp polices
sctp: remove prsctp_param from sctp_chunk
sctp: move sent_count to the memory hole in sctp_chunk
tg3: Avoid NULL pointer dereference in tg3_io_error_detected()
x86/init: Fix cr4_init_shadow() on CR4-less machines
MIPS: Fix detection of unsupported highmem with cache aliases
MIPS: Malta: Fix IOCU disable switch read for MIPS64
MIPS: Fix BUILD_ROLLBACK_PROLOGUE for microMIPS
...
The function is never called with zero 'runqueue_node'.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The runqueue worker currently issues a get() when a new
node is processed, and a put() once a node is completed.
The corresponding suspend and resume calls currently only
do clock gating, but with the upcoming introduction of
IOMMU runpm also the corresponding IOMMU domain gets
enabled (for get()) and disabled (for put()). This
introduces performance regressions with we mitigate here.
Switch PM runtime to autosuspend, such that clock gating
and IOMMU control only happens when the engine is idle for
a 'long' time.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
While the engine works on a runqueue node it does memory access to
the buffers associated with that node.
Make sure that the engine is idle when g2d_close() and/or
g2d_remove() are called, i.e. buffer associated with the process (for
g2d_close()), or all buffers (for g2d_remove()) can be safely be
unmapped.
We have to take into account that the engine might be in an undefined
state, i.e. it hangs and doesn't become idle. In this case, we issue
a hardware reset to return the hardware and the driver context into a
proper state.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The driver might be closed (and/or removed) while there are still
nodes queued for processing.
Make sure to remove these nodes, which means all of them in
the case of g2d_remove() and only those belonging to the
corresponding process in g2d_close().
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Do all pm_runtime_{get,put}() calls in the runqueue worker.
Also keep track of the engine's idle/busy state.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This reverts commit b05984e21a.
The change, i.e. merging the sleep and runpm operations, produces
a deadlock situation:
(1) exynos_g2d_exec_ioctl() prepares a runqueue node and
calls g2d_exec_runqueue()
(2) g2d_exec_runqueue() calls g2d_dma_start() which gets
runtime PM sync
(3) runtime PM core calls g2d_runtime_resume()
(4) g2d_runtime_resume() calls g2d_exec_runqueue(), which
loops back to (2)
Due to mutexes that are in place, a deadlock situation is created.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Exynos DRM framework handled page-flip event with custom code.
The patch replaces it with drm-core vblank queue.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
We get 1 warning when building kernel with W=1:
drivers/gpu/drm/exynos/exynos_dp.c:46:5: warning: no previous prototype for 'exynos_dp_crtc_clock_enable' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
So this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
In case of some platforms fimd clocks can be configured to
very low values, as a result refresh rate can be very low and
driver/drm-core will timeout waiting for vblanks, it will result
in premature removal of framebuffers and will cause oopses.
The patch adds atomic_check callback to fimd to prevent setting
such modes.
Reported-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Exynos DRM devices update their registers at vblank time. Exynos-DRM uses
custom mechanism to wait for vblank. This mechanism is error prone -
variables are not updated atomically. As a result in certain circumstances
user space can try to free buffers which are still in use by hardware,
in such cases IOMMU can throw OOPS.
The patch instead of fixing the mechanism replaces it with drm core helper.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
VIDI driver uses fake vblank handler to generate vblank events.
It was implemented using worker which slept for vblank time, additionally
it did not work if there were no page flips. The patch replaces it with
timer, uses drm_crtc_vblank_(on|off) helpers to manage it and fixes
behavior for non-page-flip cases.
This change allows further improvements of vblank in exynos-drm framework.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
A simple while loop should do the same here.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The mixer context struct already has a 'flags' field, so
we can use it to store the 'interlace', 'vp_enabled' and
'has_sclk' booleans.
We use the non-atomic helper functions to access these bits.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The helper, devm_regulator_bulk_get() initializes the consumer as NULL,
so this code can be ignored.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Paring DT properties and getting PHY IO (memory mapped or I2C) in one
function.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Paring DT properties and getting the I2C adapter in one function.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX6H4uAAoJEHm+PkMAQRiG5sMH/3yzrMiUCSokdS+cvY+jgKAG
JS58JmRvBPz2mRaU3MRPBGRDeCz/Nc9LggL2ZcgM+E1ZYirlYyQfIED3lkqk5R07
kIN1wmb+kQhXyU4IY3fEX7joqyKC6zOy4DUChPkBQU0/0+VUmdVmcJvsuPlnMZtf
g95m0BdYTui+eDezASRqOEp3Lb5ONL4c3ao4yBP0LHF033ctj3VJQiyi5uERPZJ0
5e6Mo7Wxn78t9WqJLQAiEH46kTwT2plNlxf3XXqTenfIdbWhqE873HPGeSMa3VQV
VywXTpCpSPQsA8BYg66qIbebdKOhs9MOviHVfqDtwQlvwhjlBDya0gNHfI5fSy4=
=Y/L5
-----END PGP SIGNATURE-----
Merge tag 'v4.8-rc8' into drm-next
Linux 4.8-rc8
There was a lot of fallout in the imx/amdgpu/i915 drivers, so backmerge
it now to avoid troubles.
* tag 'v4.8-rc8': (1442 commits)
Linux 4.8-rc8
fault_in_multipages_readable() throws set-but-unused error
mm: check VMA flags to avoid invalid PROT_NONE NUMA balancing
radix tree: fix sibling entry handling in radix_tree_descend()
radix tree test suite: Test radix_tree_replace_slot() for multiorder entries
fix memory leaks in tracing_buffers_splice_read()
tracing: Move mutex to protect against resetting of seq data
MIPS: Fix delay slot emulation count in debugfs
MIPS: SMP: Fix possibility of deadlock when bringing CPUs online
mm: delete unnecessary and unsafe init_tlb_ubc()
huge tmpfs: fix Committed_AS leak
shmem: fix tmpfs to handle the huge= option properly
blk-mq: skip unmapped queues in blk_mq_alloc_request_hctx
MIPS: Fix pre-r6 emulation FPU initialisation
arm64: kgdb: handle read-only text / modules
arm64: Call numa_store_cpu_info() earlier.
locking/hung_task: Fix typo in CONFIG_DETECT_HUNG_TASK help text
nvme-rdma: only clear queue flags after successful connect
i2c: qup: skip qup_i2c_suspend if the device is already runtime suspended
perf/core: Limit matching exclusive events to one PMU
...
When CONFIG_PM is not set, we get a warning about an unused function:
drivers/gpu/drm/exynos/exynos_drm_gsc.c:1219:12: error: 'gsc_clk_ctrl' defined but not used [-Werror=unused-function]
static int gsc_clk_ctrl(struct gsc_context *ctx, bool enable)
^~~~~~~~~~~~
This removes the two #ifdef checks in this file and instead marks the
functions as __maybe_unused, which is a more reliable way of doing the
same, allowing better build coverage and avoiding the warning above.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Move code from system sleep pm to runtime pm callbacks to ensure proper
driver state preservation when device is under power domain. Then, use
generic helpers for using runtime pm for system sleep pm.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Use generic helpers instead of open-coding usage of runtime pm for system
sleep pm, which was potentially broken for some corner cases.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Use generic helpers instead of open-coding usage of runtime pm for system
sleep pm, which was potentially broken for some corner cases.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Use generic helpers instead of open-coding usage of runtime pm for system
sleep pm, which was potentially broken for some corner cases.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Fix unsupported GEM memory type error message to include the memory type
information.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
With our DMA ops enabled for PCI devices, we should avoid allocating
IOVAs which a host bridge might misinterpret as peer-to-peer DMA and
lead to faults, corruption or other badness. To be safe, punch out holes
for all of the relevant host bridge's windows when initialising a DMA
domain for a PCI device.
CC: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Inki Dae <inki.dae@samsung.com>
Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Drivers may set the NO_DISABLE_AFTER_MODESET flag in the 'flags' parameter
of the helper drm_atomic_helper_commit_planes() if the relevant display
controllers(e.g., IPUv3 for imx-drm) require to disable a CRTC's planes
when the CRTC is disabled. The helper would skip the ->atomic_disable
call for a plane if the CRTC of the old plane state needs a modesetting
operation. Of course, the drivers need to disable the planes in their CRTC
disable callbacks since no one else would do that.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472461923-14364-1-git-send-email-gnuiyl@gmail.com
The s5p-tv driver has been replaced by the exynos drm driver for quite a
long time now. Remove this driver to avoid having duplicate drivers,
of which this one is considered dead code by Samsung.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pull drm zpos property support from Dave Airlie:
"This tree was waiting on some media stuff I hadn't had time to get a
stable branchpoint off, so I just waited until it was all in your tree
first.
It's been around a bit on the list and shouldn't affect anything
outside adding the generic API and moving some ARM drivers to using
it"
* tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux:
drm: rcar: use generic code for managing zpos plane property
drm/exynos: use generic code for managing zpos plane property
drm: sti: use generic zpos for plane
drm: add generic zpos property
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Backmerge drm-next to be able to apply Chris' connector_unregister_all
cleanup (need latest i915 and sun4i state for that).
Also there's a trivial conflict in ttm_bo.c that git rerere fails to
remember.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Please consider merging this tag, which contains the v4 misc fixes and add RK3399 eDP support patches[0] I sent on 2016-06-29, rebased onto v4.7-rc5.
* 'upstream/analogix-dp-20160705' of git://github.com/yakir-Yang/linux:
dt-bindings: analogix_dp: rockchip: correct the wrong compatible name
drm/rockchip: analogix_dp: introduce the pclk for grf
drm/bridge: analogix_dp: fix no drm hpd event when panel plug in
drm/rockchip: analogix_dp: update the comments about why need to hardcode VOP output mode
drm/rockchip: analogix_dp: correct the connector display color format and bpc
drm/bridge: analogix_dp: passing the connector as an argument in .get_modes()
drm/rockchip: analogix_dp: make panel detect to an optional action
drm/rockchip: analogix_dp: add rk3399 eDP support
drm/bridge: analogix_dp: some rockchip chips need to flip REF_CLK bit setting
drm/bridge: analogix_dp: correct the register bit define error in ANALOGIX_DP_PLL_REG_1
drm/rockchip: analogix_dp: split the lcdc select setting into device data
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
This pull request adds to the rework patch series for IOMMU
integration to support ARM64bit architecture with DMA-IOMMU
glue code.
With this patch series, Exynos DRM works well on Exynos5433 SoC
with IOMMU enabled.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: iommu: add support for ARM64 specific code for IOMMU glue
drm/exynos: iommu: move ARM specific code to exynos_drm_iommu.h
drm/exynos: iommu: remove unused entries from exynos_drm_private strcuture
drm/exynos: iommu: add a check if all sub-devices have iommu controller
drm/exynos: iommu: move dma_params configuration code to separate functions
I recovered dri-devel backlog from my vacation, more misc stuff:
- of_put_node fixes from Peter Chen (not all yet)
- more patches from Gustavo to use kms-native drm_crtc_vblank_* funcs
- docs sphinxification from Lukas Wunner
- bunch of fixes all over from Dan Carpenter
- more follow up work from Chris register/unregister rework in various
places
- vgem dma-buf export (for writing testcases)
- small things all over from tons of different people
* tag 'topic/drm-misc-2016-07-14' of git://anongit.freedesktop.org/drm-intel: (52 commits)
drm: Don't overwrite user ioctl arg unless requested
dma-buf/sync_file: improve Kconfig description for Sync Files
MAINTAINERS: add entry for the Sync File Framework
drm: Resurrect atomic rmfb code
drm/vgem: Use PAGE_KERNEL in place of x86-specific PAGE_KERNEL_IO
qxl: silence uninitialized variable warning
qxl: check for kmap failures
vga_switcheroo: Sphinxify docs
drm: Restore double clflush on the last partial cacheline
gpu: drm: rockchip_drm_drv: add missing of_node_put after calling of_parse_phandle
gpu: drm: sti_vtg: add missing of_node_put after calling of_parse_phandle
gpu: drm: sti_hqvdp: add missing of_node_put after calling of_parse_phandle
gpu: drm: sti_vdo: add missing of_node_put after calling of_parse_phandle
gpu: drm: sti_compositor: add missing of_node_put after calling of_parse_phandle
drm/tilcdc: use drm_crtc_handle_vblank()
drm/rcar-du: use drm_crtc_handle_vblank()
drm/nouveau: use drm_crtc_handle_vblank()
drm/atmel: use drm_crtc_handle_vblank()
drm/armada: use drm_crtc_handle_vblank()
drm: make drm_vblank_count_and_time() static
...
This patch adds support for ARM 64bit architecture with IOMMU-DMA glue
code, so Exynos DRM can be now used on Exynos 5433 with IOMMU enabled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch moves all ARM 32bit DMA-mapping/IOMMU dependant code from
exynos_drm_iommu.c to .h, to let it compile conditionally and prepare
for adding support for other architectures/IOMMU glue code (like ARM
64bit with IOMMU-DMA glue). Later, when ARM 32bit and 64bit will be
unified, this code can be removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch removes unused entries from exynos_drm_private strcuture.
da_start/da_space_size were only used in drm_create_iommu_mapping()
function and never set to other value than the defaults. Instead use
default values directly in arm_iommu_create_mapping() call.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds a check if all devices belonging to Exynos DRM have the
same dma_map_ops set. This is required to enable operation with IOMMU
enabled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Move code for managing DMA max segment size parameter to separate
functions. This patch also replaces devm_kzalloc() with kzalloc() and
adds proper kfree call. devm_kzalloc() cannot be used for dma_params
structure, because it will be freed on driver remove not on device
release. This means in case of Exynos DRM being compiled as module and
loaded 2 times, a user-after-free issue will happen.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
It's better to pass the connector to platform driver in .get_modes()
callback, just like what the .get_modes() helper function designed.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXcHi9AAoJEHm+PkMAQRiGSJ0H/2o4t9VWYmhyPC1sdIHoCExJ
P4tBrcZYBmKcsOmIfnJDa5g/+IdhouEUM0v0fHPogS2UUWT9eRuJWYD3sY+HpEQ+
heKTli8X73gsFB25odeIbIt0jAoSiiMYWDrWqLNsuUV1tjEYVA8rH0SM94FiOC/5
7WVWXLTuH+Rm7JHP18BnKxmMMbzrTFmwisLMqFKyfZRRSlS+/ix7iLUNO9AFa39B
YHxNPihLrZ0oONyCOAQoHTIXXrw0cQbxV2utg3vnMcCZdme2xOn+iXMntTSKfZ39
iC9/T0vsO3R6OrRo2aDZAnCPUAniXnMEIhrKG37WMyXpj6cucZ/2QiNXcXviGV4=
=iLte
-----END PGP SIGNATURE-----
Back-merge tag 'v4.7-rc5' into drm-next
Linux 4.7-rc5
The fsl-dcu pull needs -rc3 so go to -rc5 for now.
We already have a fallback in place to fill out the unique from
dev->unique, which is set to something reasonable in drm_dev_alloc.
Which means we only need to have a special set_busid for pci devices,
to be able to care the backwards compat code for drm 1.1 around, which
libdrm still needs.
While developing and testing this patch things blew up in really
interesting ways, and the code is rather confusing in naming things
between the kernel code, ioctl #defines and libdrm. For the next brave
dragon slayer, document all this madness properly in the userspace
interface section of gpu.tmpl.
v2: Make drm_dev_set_unique static and update kerneldoc.
v3: Entire rewrite, plus document what's going on for posterity in the
gpu docbook uapi section.
v4: Drop accidental amdgpu hunk (Emil).
v5: Drop accidental omapdrm vblank counter change (Emil).
v6: Rebase on top of the sphinx conversion.
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> (virt_gpu)
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The current bitwise AND should result in the same assembler
but this is what the code is actually supposed to do.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Neither of these files issue any fbdev related calls.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This makes the defines consistent with the rest.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Commit a6f75aa161 ("drm/exynos: fimd: add HW trigger support") added
hardware trigger support to the FIMD controller driver. But this broke
the display in at least the Exynos5800 Peach Pi Chromebook.
So until the issue is fixed, avoid using HW trigger for the Exynos5420
based boards and use SW trigger as it was before the mentioned commit.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The field value is only checked in fimd_setup_trigger() if .trg_type is
I80_HW_TRG so there's no point in setting this field for the s3c6400 if
is never going to be used since .trg_type is not set.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Commit 3424e3a4f8 ("drm: bridge: analogix/dp: split exynos dp driver to
bridge directory") split the Exynos DP core driver into a core driver and
a bridge driver for the Analogix chip since that is also used by Rockchip.
But the change introduced a regression causing a NULL pointer dereference
when trying to access an uninitialized connector in the driver .get_modes:
Fix this by instead of having a connector struct for both the Exynos and
Analogix drivers, just use the connector initialized in the bridge driver.
Fixes: 3424e3a4f8 ("drm: bridge: analogix/dp: split exynos dp driver to bridge directory")
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
We have 1:1 relationship between connectors and encoders and the driver
is relying on the atomic helpers: we can drop the custom ->best_encoder()
implementations and let the core call drm_atomic_helper_best_encoder()
for us.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465300095-16971-5-git-send-email-boris.brezillon@free-electrons.com
This was added in
commit 0a3e67a4ca
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Sep 30 12:14:26 2008 -0700
drm: Rework vblank-wait handling to allow interrupt reduction.
to stay backwards-compatible with old UMS code that didn't even tell
the kernel when it did a modeset, so that the kernel could
save/restore vblank counters. At worst this means vblanks will be
somewhat funky on a setup that very likely no one still runs.
So let's just nuke it.
Plan B would be to set it unconditionally in drm_vblank_init for kms
drivers, instead of in each driver separately. So if this patch breaks
anything please only restore the hunks in drmP.h and drm_irq.c, plus
add a check for DRIVER_MODESET in drm_vblank_init.
Stumbled over this in a discussion on irc with Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_gem_object_lookup() has never required the drm_device for its file
local translation of the user handle to the GEM object. Let's remove the
unused parameter and save some space.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: dri-devel@lists.freedesktop.org
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Fixup kerneldoc too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I kinda hoped that I could still sneak in Noralf's
drm_simple_display_pipe, since there's intereset by others now (for tilcdc
at least). But it wasn't ready by a hair. Oh well.
Otherwise random stuff plus prep patches from Noralf.
* tag 'topic/drm-misc-2016-05-13' of git://anongit.freedesktop.org/drm-intel:
drm/atomic: Add drm_atomic_helper_best_encoder()
drm/atomic: Don't skip drm_bridge_*() calls if !drm_encoder_helper_funcs
drm/fb-cma-helper: Hook up to DocBook and fix some docs
drm/fb-helper: Remove mention of CONFIG_FB_DEFERRED_IO in docs
drm/sti: include linux/seq_file.h where needed
drm/tegra: Use lockless gem BO free callback
drm/exynos: Use lockless gem BO free callback
drm: Make drm_encoder_helper_funcs optional
It seems trigger cannot be configured too early, otherwise it does not work in
case of panel. The patch fixes also trigger flag logic, previously HW-TRIGGER
flag was cleared in case of panel - as a result panel used always software
trigger.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This allows to remove the local of_graph_get_port_by_reg(),
of_graph_get_endpoint_by_reg(), and of_get_child_by_name_reg()
functions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Inki Dae <inki.dae@samsung.com>
This allows to remove the local of_graph_get_port_by_reg(),
of_graph_get_endpoint_by_reg(), of_get_child_by_name_reg(),
and of_graph_get_remote_port_parent() functions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
It's an optional hook. Might be needed for frontbuffer rendering on
manual upload displays, but a simple TODO doesn't explain at all what
needs to be done or why.
Cc: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
There is no reason to be wapper functions to use DMA mapping APIs. Use
directly DMA mapping APIs and remove the wapper functions.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The regulators may not be available just because their driver's probe
function was just not executed and so the regulators not registered.
So, in this case the Exynos HDMI driver should not print logs since
a -EPROBE_DEFER is not really an error and that will just pollute
the kernel log and confuse users.
This patch prevents the following misleading messages to be printed:
[ 1.443638] [drm:hdmi_probe] *ERROR* failed to get regulators
[ 1.449326] [drm:hdmi_probe] *ERROR* hdmi_resources_init failed
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The imported dma-buf should be mapped by sub-system exporting it.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This allows exported dma-bufs to be mapped using gem_prime_mmap.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Don't use the vrefresh field of the DRM mode since this
one is supposed to only be used for debug purpose.
Instead use the clock field which should also provide
much more precise information.
Also sanitize the case in which the clock value
should be zero. We then just default to the maximum
clock divisor.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Software trigger should not be used if hardware trigger is configured.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
vblank should be signaled to userspace after reading framebuffers not before,
signaling it in TE interrupt looks wrong. TE triggers reading framebuffers
so it is the worst moment. Tearing is not observable because hardware prevents
it, but there are frequently skipped vblank events.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
HDMI-PHY clock should be accessible from other components in the pipeline.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXL7HfAAoJEHm+PkMAQRiGYe8IAJBGaPUq38EJh2YOV+AQf9v6
t/alhwB3DUE1E0zjLy7I7JJ+xDXtKjZh9fS6OFuIS8Q3RIrBteIJ/oH8TPpt7yZ/
SnP6rYPvYD6CImTyrh7+ORL/udEwJX8+YqFYAgUAq167gvpDjYj8r26VzdIaIN4/
oBbL8NrQNWfODieywYyhUoitVhwMz09zmBfLtGVks4vd2jUJk2Fdd9cOtGV5tRfk
DPndPgyQtbr8W0mKovV8sT9WkQeV5TsUr4MLgf7hjnAGYQ8+0KamkzzVVLBeBiiw
uazyrOCFkddZp+N7KbmbOmazV/yULRuLGgDjVKazoCsOaKOvoGCzrCk7daOPy6Q=
=CegX
-----END PGP SIGNATURE-----
Merge tag 'v4.6-rc7' into drm-next
Merge this back as we've built up a fair few conflicts, and I have
some newer trees to pull in.
Ofc I promise just a few leftovers for drm-misc and somehow it's the
biggest pull. But really mostly trivial stuff:
- MAINTAINERS updates from Emil
- rename async to nonblock in atomic_commit to avoid the confusion between
nonblocking ioctl and async flip (= not vblank synced), from Maarten.
Needs to be regened with newer drivers, but probably only after -rc1 to
catch them all.
- actually lockless gem_object_free, plus acked driver conversion patches.
All the trickier prep stuff already is in drm-next.
- Noralf's nice work for generic defio support in our fbdev emulation.
Keeps the udl hack, and qxl is tested by Gerd.
* tag 'topic/drm-misc-2016-05-04' of git://anongit.freedesktop.org/drm-intel: (47 commits)
drm: Fixup locking WARN_ON mistake around gem_object_free_unlocked
drm/etnaviv: Use lockless gem BO free callback
drm/imx: Use lockless gem BO free callback
drm/radeon: Use lockless gem BO free callback
drm/amdgpu: Use lockless gem BO free callback
drm/gem: support BO freeing without dev->struct_mutex
MAINTAINERS: Add myself for the new VC4 (RPi GPU) graphics driver.
MAINTAINERS: Add a bunch of legacy (UMS) DRM drivers
MAINTAINERS: Add a few DRM drivers by Dave Airlie
MAINTAINERS: List the correct git repo for the Renesas DRM drivers
MAINTAINERS: Update the files list for the Renesas DRM drivers
MAINTAINERS: Update the files list for the Armada DRM driver
MAINTAINERS: Update the files list for the Rockchip DRM driver
MAINTAINERS: Update the files list for the Exynos DRM driver
MAINTAINERS: Add maintainer entry for the VMWGFX DRM driver
MAINTAINERS: Add maintainer entry for the MSM DRM driver
MAINTAINERS: Add maintainer entry for the Nouveau DRM driver
MAINTAINERS: Update the files list for the Etnaviv DRM driver
MAINTAINERS: Remove unneded wildcard for the i915 DRM driver
drm/atomic: Add WARN_ON when state->acquire_ctx is not set.
...
This patch removes suffixes from I80 relevant register definitions,
which are misleading.
This is based on top of below patch set,
http://www.spinics.net/lists/dri-devel/msg104057.html
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch cleans up interface type relevant codes.
Trigger mode is determinded only by i80 mode, which isn't
related to Display types - HDMI or Display controller.
So this patch makes the trigger mode to be set only in case of
i80 mode - For DECON-TV, HW Trigger mode is flaged mandatorily
because HDMI Timing Generator generates VSYNC signal
which works as a hardware trigger.
Changelog v2.
- If interface type is HDMI then set out_type to I80.
- fix compile warning.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds HW trigger support on i80 mode.
Until now, Exynos DRM only supported SW trigger which was set
SWTRGCMD bit of TRIGCON register by CPU to transfer scanout
buffer to Display bus device or panel.
With this patch, the transmission to Display bus device or
panel will be initiated by FIMD controller.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch cleans up wait_for_vblank relevant codes.
wait_for_vblank callback isn't used anymore in Exynos drm driver
so it removes relevant codes. However, display controllers -
FIMD and DECON - still use this function driver internally
to ensure shadow registers to be updated, which resolves
page fault issue so keep it.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
There are no non-devicetree based Exynos platforms in mainline, so there
no point keeping old platform driver data for them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Simplify code by replacing custom code by generic helper and add missing
const qualifier to driver data structures.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
clock_enable callback is used only by FIMD->DP pipeline. Similar but more
universal functionality provides pipeline clock.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <daeinki@gmail.com>
According to documentation HDMI-PHY must be on prior to MIXER configuration.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Components belonging to the same pipeline often requires
synchronized clocks. Such clocks are sometimes provided
by external clock controller, but they can be also provided by
pipeline components. In latter case there should be a way
to access them from another component belonging to the same pipeline.
This is the case of:
- DECON,FIMD -> HDMI and HDMI-PHY clock,
- FIMD -> DP and DP clock in FIMD.
The latter case has been solved by clock_enable callback
in exynos_drm_crtc_ops. This solutin will not work with
HDMI path as in this case clock is provided by encoder.
This patch provides more generic solution allowing to register
pipeline clock during initialization in exynos_drm_crtc structure.
This way the clock will be easily accessible from both components.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The helper abstracts out conversion from pipeline
to crtc. Currently it is used in two places, but
there will be more uses in next patches.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
decon_atomic_begin and decon_atomic_flush protects all windows already.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Resetting IP at starting ensures that DECON will be in known state
regardless of changes by bootloader.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DECON should be updated after un-protecting windows and after changing
output parameters, otherwise image is not displayed in case of HDMI path.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
HDMI registry dump unnecessary spoils console and is not very helpful.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
To ensure HDMI-PHY reprogramming will not affect
HDMI the latter should be reset.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
HDMI-PHY power off bit defaults to 0 in older HDMI versions.
In case of Exynos5433 it defaults to 1. To make code
consistent across all versions this bit is always unset/set in
power on/off sequences.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Proper PHY configuration should be as follow:
1. set HDMI clock parents to OSCCLK.
2. reconfigure PHY.
3. set HDMI clock parents to PHY.
4. wait for PLL stabilization.
The patch fixes it and consolidates the code.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
HDMI on Exynos5433 differs from previous versions:
- different HDMI-PHY settings,
- different clocks,
- SYSREG registers for enabling reference clock,
- MODE_SET register in HDMI-PHY.
It is distinguished from other variants by different compatible string.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
There is no point in rewriting default values, as the IP is reset anyway.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
HDMI-PHY configurations are stored as array pointer and count pair,
we can re-use existing helpers to simplify their initialization.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
With incoming support for newer SoCs different set of clocks will be required,
depending on IP version. The patch prepares the driver for it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Commit 254d4d111e ("drm/exynos: Add dependency for G2D in Kconfig") made
the DRM_EXYNOS_G2D symbol to only be selectable if the s5p-g2d V4L2 driver
is not enabled, since both use the same HW IP block.
But added the dependency as depends on !VIDEO_SAMSUNG_S5P_G2D which isn't
correct since Kconfig expressions are not boolean but tristate. So it will
only evaluate to 'n' if VIDEO_SAMSUNG_S5P_G2D=y but it will evaluate to m
if VIDEO_SAMSUNG_S5P_G2D=m.
This means that both the V4L2 and DRM drivers can be enabled if the former
is enabled as a module, which is not what we want.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The "ret = regmap_write()" assignment was missing so this error message
is never printed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
We accidentally return success instead of a negative error code here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Commit 1feafd3afd ("drm/exynos: add
exynos5420 support for fimd") add support for Exynos 5420 SoC, but it
broke enabling display clock feature because of incorrect condition
check. This patch fixes it, so display is working again on platforms
requiring display clock control (i.e. Exynos5250-based SNOW platform).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Fbdev code should be compiled only if CONFIG_DRM_FBDEV_EMULATION option
is enabled. The patch fixes exynos-drm code trying to manipulate
fbdev data which is not initialized in case CONFIG_DRM_FBDEV_EMULATION
is disabled.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
exynos_plane_mode_set should use adjusted_mode from the same atomic state as
plane state. Otherwise it will result in incorrect behavior in case
crtc mode changes.
The patch fixes bug with black console framebuffer in case of command mode
panels.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
gcc-6 warns about a pointless loop in exynos_drm_subdrv_open:
drivers/gpu/drm/exynos/exynos_drm_core.c: In function 'exynos_drm_subdrv_open':
drivers/gpu/drm/exynos/exynos_drm_core.c:104:199: error: self-comparison always evaluates to false [-Werror=tautological-compare]
list_for_each_entry_reverse(subdrv, &subdrv->list, list) {
Here, the list_for_each_entry_reverse immediately terminates because
the subdrv pointer is compared to itself as the loop end condition.
If we were to take the current subdrv pointer as the start of the
list (as we would do if list_for_each_entry_reverse() was not a macro),
we would iterate backwards over the &exynos_drm_subdrv_list anchor,
which would be even worse.
Instead, we need to use list_for_each_entry_continue_reverse()
to go back over each subdrv that was successfully opened until
the first entry.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The only things this protects is reading ->flags and ->size, both of
which are invariant over the lifetime of an exynos gem bo. So no
locking needed at all (besides that, nothing protects the writers
anyway).
Aside: exynos_gem_obj->size is redundant with
exynos_gem_obj->base.size and probably should be removed.
v2: Use _unlocked unreference (Daniel Stone).
Cc: Daniel Stone <daniel@fooishbar.org>
Cc: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459330852-27668-9-git-send-email-daniel.vetter@ffwll.ch
Simply forgotten about this when I was doing my general cleansing of
simple gem mmap offset functions. There's nothing but core functions
called here, and they all have their own protection already.
Aside: DRM_ERROR for userspace controlled input isn't great, but
that's for another patch.
v2: Use _unlocked unreference (Daniel Stone).
Cc: Daniel Stone <daniel@fooishbar.org>
Cc: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459330852-27668-7-git-send-email-daniel.vetter@ffwll.ch
Commit 254d4d111e ("drm/exynos: Add dependency for G2D in Kconfig") made
the DRM_EXYNOS_G2D symbol to only be selectable if the s5p-g2d V4L2 driver
is not enabled, since both use the same HW IP block.
But added the dependency as depends on !VIDEO_SAMSUNG_S5P_G2D which isn't
correct since Kconfig expressions are not boolean but tristate. So it will
only evaluate to 'n' if VIDEO_SAMSUNG_S5P_G2D=y but it will evaluate to m
if VIDEO_SAMSUNG_S5P_G2D=m.
This means that both the V4L2 and DRM drivers can be enabled if the former
is enabled as a module, which is not what we want.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The "ret = regmap_write()" assignment was missing so this error message
is never printed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
We accidentally return success instead of a negative error code here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Commit 1feafd3afd ("drm/exynos: add
exynos5420 support for fimd") add support for Exynos 5420 SoC, but it
broke enabling display clock feature because of incorrect condition
check. This patch fixes it, so display is working again on platforms
requiring display clock control (i.e. Exynos5250-based SNOW platform).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Fbdev code should be compiled only if CONFIG_DRM_FBDEV_EMULATION option
is enabled. The patch fixes exynos-drm code trying to manipulate
fbdev data which is not initialized in case CONFIG_DRM_FBDEV_EMULATION
is disabled.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
exynos_plane_mode_set should use adjusted_mode from the same atomic state as
plane state. Otherwise it will result in incorrect behavior in case
crtc mode changes.
The patch fixes bug with black console framebuffer in case of command mode
panels.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
gcc-6 warns about a pointless loop in exynos_drm_subdrv_open:
drivers/gpu/drm/exynos/exynos_drm_core.c: In function 'exynos_drm_subdrv_open':
drivers/gpu/drm/exynos/exynos_drm_core.c:104:199: error: self-comparison always evaluates to false [-Werror=tautological-compare]
list_for_each_entry_reverse(subdrv, &subdrv->list, list) {
Here, the list_for_each_entry_reverse immediately terminates because
the subdrv pointer is compared to itself as the loop end condition.
If we were to take the current subdrv pointer as the start of the
list (as we would do if list_for_each_entry_reverse() was not a macro),
we would iterate backwards over the &exynos_drm_subdrv_list anchor,
which would be even worse.
Instead, we need to use list_for_each_entry_continue_reverse()
to go back over each subdrv that was successfully opened until
the first entry.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Fix some obvious alignment problems, like alignment and line
over 80 characters problems, make this easy to be maintained
later.
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
The core functionality now resides in the generic bridge part so the
exynos-specific implementation details can get a more suitable nameing.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Split the dp core driver from exynos directory to bridge directory,
and rename the core driver to analogix_dp_*, rename the platform
code to exynos_dp.
Beside the new analogix_dp driver would export six hooks.
"analogix_dp_bind()" and "analogix_dp_unbind()"
"analogix_dp_suspned()" and "analogix_dp_resume()"
"analogix_dp_detect()" and "analogix_dp_get_modes()"
The bind/unbind symbols is used for analogix platform driver to connect
with analogix_dp core driver. And the detect/get_modes is used for analogix
platform driver to init the connector.
They reason why connector need register in helper driver is rockchip drm
haven't implement the atomic API, but Exynos drm have implement it, so
there would need two different connector helper functions, that's why we
leave the connector register in helper driver.
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The commit d931589c01 ("drm/exynos: remove DRM_EXYNOS_GEM_MAP_OFFSET
ioctl") removed it same with the ioctl that this patch adds. The reason
that removed DRM_EXYNOS_GEM_MAP_OFFSET was we could use
DRM_IOCTL_MODE_MAP_DUMB. Both did exactly same thing.
Now we again will revive it as DRM_EXYNOS_GEM_MAP because of render
node. DRM_IOCTL_MODE_MAP_DUMB isn't permitted in render node.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Core provides generic helper to create DSI packet, use it instead of
custom code.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch changes device pointer provided to all calls to DMA-mapping
subsystem from the virtual exynos-drm 'device' to the real device pointer
of one of the CRTC devices (decon, fimd or mixer). This way no more hacks
will be needed to configure proper DMA-mapping address space on the common
virtual exynos-drm device. This change also removes the need for some
hacks in IOMMU related code. It also finally solves the problem of Exynos
DRM driver not working on ARM64 architecture, which provides noop-based
DMA-mapping operations for virtual platform devices.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch refactors driver and device registration by moving all drivers
to the common array. This way additional flags can be added later for
new features. #ifdef-based code has been replaced by IS_ENABLED() macro
usage.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Polarization was never configured for DRM-FIMC device, so fimc_set_polarity
function did nothing. In fact DRM does not use camera interface so there
is no point in configuring it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
struct exynos_drm_panel_info is not used anymore, except exynos_dp,
which can integrate useful fields directly into its context.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds a exynos5420 driver data to support mic_bypass
option to bypass the mic from display out path.
The mic(Mobile image compressor) compresses RGB data from fimd
and send the compressed data to the mipi dsi.
The bypass option can be founded from system register and the bit
is 11. The option bit has been introduced since exynos5420. The
only difference between exynos5250 and exynos5420/exynos5422 is
existence of the bit. Until the MIC is defined and enabled from
device tree, the bypass mic will be default option.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch uses DIV_ROUND_CLOSEST instead of DIV_ROUND_UP
The DIV_ROUND_CLOSEST can be used to find the closest integer
value when we divide some integers.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Include directories are provided by core already, adding them in driver
is redundand and causes warnings in case of out-of-tree build.
v2:
- fixed include in exynos_drm_iommu.c
- typo in commit message
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Functions are preferred over macros as more type-safe.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Andrzej Hajda
Tobias Jakobi
Inki Dae
Hoegeun Kwon
Daniel Vetter
Gustavo Padovan
Michal Hocko
Dave Airlie
Linus Torvalds
Hans Verkuil
Rob Herring
Krzysztof Kozlowski
Dan Carpenter
Dave Jiang
Laurent Pinchart
Shawn Guo
Gabriel Krisman Bertazi
Joonyoung Shim
Marek Szyprowski
Bhumika Goyal
Laurent Pinchart
Ville Syrjälä
Jan Kara
Javier Martinez Canillas
Colin Ian King
Shuah Khan
Arvind Yadav
Stefan Christ
Jani Nikula
Lorenzo Stoakes
Chris Wilson
Mauro Carvalho Chehab
Baoyou Xie
Milo Kim
Arnd Bergmann
Robin Murphy
Liu Ying
Hans Verkuil
Krzysztof Kozlowski
Markus Elfring
Peter Chen
Yakir Yang
Boris Brezillon
Philipp Zabel
Maarten Lankhorst
Heiko Stuebner
Chanho Park
Chanho Park