Right now the driver uses only 3 LED modes:
0: On
1: HW Blinking (Interval 1)
3: Off
However, the controller supports a second HW blinking interval, which results
in 4 possible LED modes:
0: On
1: HW Blinking (Interval 1)
2: HW Blinking (Interval 2)
3: Off
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each nibble represents 4 LEDs, and in case of the higher register, bit 0
represents LED 4, so we need to use modulus for the LED number as well.
Fixes: fd7b025a23 ("leds: add BCM6328 LED driver")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
BCM6328 controller has a margin of 20ms per blink step, which means that
we can only set it to 20, 40, 60 ... 1260 ms (0x3f * 20ms).
However, when checking if delay_on == delay_off, we were not considering
the case when the user had set delay_on=20 and delay_off=21, since this
will cause the driver to fallback to software blinking.
This update fixes this issue and improves blink steps by rounding them
in a more sensible way. Now 30-49ms is rounded to 40 ms, and previous
behaviour implied 40-59ms being rounded to 40 ms.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Instead of duplicating the unlock we can store the return value and use a
single unlock before returning that value, which simplifies the code.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This adds little endian support while keeping big endian support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This lock isn't really needed, since we're only reading the register and
changes made to other LEDs aren't relevant.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The values of BCM6328_LED_MODE_ON and BCM6328_LED_MODE_OFF were named
for active low LEDs. These should be swapped so that they are named for
the default case of active high LEDs.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
When ensuring a consistent initial LED state in bcm6328_led (as they may
be blinking instead of on/off), the LED register is set using an inverted
copy of bcm6328_led_set(). To avoid further errors relating to active low
handling, call this function directly instead.
As bcm6328_led_set() acquires the same spinlock again when updating the
register, it is called after unlocking.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
for_each_available_child_of_node performs an of_node_get on each
iteration, so a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch adds more init register configuration options:
- Serial LEDs multiplexing.
- Serial LEDs clock signal low/high polarity.
- Serial LEDs data signal low/high polarity.
- Serial LEDs shift direction inverted/normal.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch simplifies and improves the code related to
default-state handling.
It also changes the code to power off the LEDs by default.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Print invalid LED instead of warning only about maximum LED value.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This adds support for the LED controller on Broadcom's BCM6328.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Álvaro Fernández Rojas
Markus Elfring
Thomas Gleixner
Jonas Gorski
Simon Arlott
Julia Lawall
Luis de Bethencourt