Qdiscs can be offloaded to HW, but current implementation isn't uniform.
Instead, qdiscs either pass information about offload status via their
TCA_OPTIONS or omit it altogether.
Introduce a new attribute - TCA_HW_OFFLOAD that would form a uniform
uAPI for the offloading status of qdiscs.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a hunk of code that is incorrectly indented with spaces
and rather than a tab. Clean this up.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
Add SFF module support
Add support for SFF modules. SFF modules are similar to SFP modules,
but they have fewer control signals, and are soldered down rather than
pluggable.
They also have different IDs in the EEPROM to identify as soldered down
SFF modules.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for SFF modules, which are soldered down SFP modules.
These have a different phys_id value, and also have the present and
rate select signals omitted compared with their socketed counter-parts.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add "sff,sff" for SFF module support with SFP. These have a different
phys_id value, and also have the present and rate select signals omitted
compared with their socketed counter-parts.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman says:
====================
nfp: fix rtsym and XPB register handling in debug dump
this series resolves two problems in the recently added debug dump facility.
* Correctly handle reading absolute rtysms
* Correctly handle special-case PB register reads
These fixes are for code only present in net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For XPB registers reads, some island IDs require special handling (e.g.
ARM island), which is already taken care of in nfp_xpb_readl(), so use
that instead of a straight CPP read.
Without this fix all "xpbm:ArmIsldXpbmMap.*" registers are reported as
0xffffffff. It has also been observed to cause a system reboot.
With this fix correct values are reported, none of which are 0xffffffff.
The values may be read using ethtool debug level 2.
# ethtool -W <netdev> 2
# ethtool -w <netdev> data dump.dat
Fixes: 0e6c4955e1 ("nfp: dump CPP, XPB and direct ME CSRs")
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In TLV-based ethtool debug dumps, don't do a CPP read for absolute
rtsyms, use the addr field in the symbol table directly as the value.
Without this fix rtsym gro_release_ring_0 is 4 bytes of zeros.
With this fix the correct value, 0x0000004a 0x00000000 is reported.
The values may be read using ethtool debug level 2.
# ethtool -W <netdev> 2
# ethtool -w <netdev> data dump.dat
Fixes: e1e798e3fd ("nfp: dump rtsyms")
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh says:
====================
net: aquantia: Atlantic driver 12/2017 updates
The patchset contains important hardware fix for machines with large MRRS
and couple of improvement in stats and capabilities reporting
patch v3:
- Fixed patch #7 after Andrew's finding. NIC level stats actually
have to be cleaned only on hw struct creation (and this is done
in kzalloc). On each hwinit we only have to reset link state
to make sure hw stats update will not increment nic stats during init.
patch v2:
- split into more detailed commits
Comment from David on wrong defines case will be submitted separately later
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a suffix to distinguish kernel mainline version and aquantia releases
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On very first start we should read out current HW counter values
to make diff based calculations later.
This also should be done each time NIC gets down/up or wakes up
after sleep state. We reset link state explicitly to prevent diffs
from being summed this first time.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce timeout from 2 secs to 1 sec. If link is down,
reduce it to 500msec. This speeds up link detection.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This metric comes from HW and is also diff-calculated, like other counters
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally they were filled from ring sw counters.
These sometimes incorrectly calculate byte and packet amounts
when using LRO/LSO and jumboframes. Filling ndev counters from
hardware makes them precise.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device hardware provides only 32bit counters. Using these directly
causes byte counters to overflow soon. A separate nic level structure
with 64 bit counters is now used to collect incrementally all the stats
and report these counters to ethtool stats and ndev stats.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Systems with large MRRS on device (2K, 4K) with high data rates and/or
large MTU, atlantic observes DMA packet buffer overflow. On some systems
that causes PCIe transaction errors, hardware NMIs or datapath freeze.
This patch
1) Limits MRRS from device side to 2K (thats maximum our hardware supports)
2) Limit maximum size of outstanding TX DMA data read requests. This makes
hardware buffers running fine.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different hardware device Ids correspond to different maximum speed
available. Extra checks were added for devices D108 and D109 to
remove unsupported speeds from these device capabilities list.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
William Tu says:
====================
ERSPAN version 2 (type III) support
ERSPAN has two versions, v1 (type II) and v2 (type III). This patch
series add support for erspan v2 based on existing erspan v1
implementation. The first patch refactors the existing erspan v1's
header structure, making it extensible to put additional v2's header.
The second and third patch introduces erspan v2's implementation to
ipv4 and ipv6 erspan, for both native mode and collect metadata mode.
Finally, test cases are added under the samples/bpf.
Note:
ERSPAN version 2 has many features and this patch does not implement
all. One major use case of version 2 over version 1 is its timestamp
and direction. So the traffic collector is able to distinguish the
mirrorred traffic better. Other features such as SGT (security group
tag), FT (frame type) for carrying non-ethernet packet, and optional
subheader are not implemented yet.
Example commandline for ERSPAN version 2:
ip link add dev ip6erspan11 type ip6erspan seq key 102 \
local fc00💯:2 remote fc00💯:1 \
erspan_ver 2 erspan_dir 1 erspan_hwid 17
The corresponding iproute2 patch:
https://marc.info/?l=linux-netdev&m=151321141525106&w=2
William Tu (4):
net: erspan: refactor existing erspan code
net: erspan: introduce erspan v2 for ip_gre
ip6_gre: add erspan v2 support
samples/bpf: add erspan v2 sample code
include/net/erspan.h | 152 ++++++++++++++++++++++++++++++++++++++---
include/net/ip6_tunnel.h | 3 +
include/net/ip_tunnels.h | 5 +-
include/uapi/linux/if_ether.h | 1 +
include/uapi/linux/if_tunnel.h | 3 +
net/ipv4/ip_gre.c | 124 +++++++++++++++++++++++++++------
net/ipv6/ip6_gre.c | 139 +++++++++++++++++++++++++++++++------
net/openvswitch/flow_netlink.c | 8 +--
samples/bpf/tcbpf2_kern.c | 77 ++++++++++++++++++---
samples/bpf/test_tunnel_bpf.sh | 38 ++++++++---
10 files changed, 472 insertions(+), 78 deletions(-)
--
A simple script to test it:
set -ex
function cleanup() {
set +ex
ip netns del ns0
ip link del ip6erspan11
ip link del veth1
}
function main() {
trap cleanup 0 2 3 9
ip netns add ns0
ip link add veth0 type veth peer name veth1
ip link set veth0 netns ns0
# non-namespace
ip addr add dev veth1 fc00💯:2/96
if [ "$1" == "v1" ]; then
echo "create IP6 ERSPAN v1 tunnel"
ip link add dev ip6erspan11 type ip6erspan seq key 102 \
local fc00💯:2 remote fc00💯:1 \
erspan 123 erspan_ver 1
else
echo "create IP6 ERSPAN v2 tunnel"
ip link add dev ip6erspan11 type ip6erspan seq key 102 \
local fc00💯:2 remote fc00💯:1 \
erspan_ver 2 erspan_dir 1 erspan_hwid 17
fi
ip addr add dev ip6erspan11 fc00:200::2/96
ip addr add dev ip6erspan11 10.10.200.2/24
# namespace: ns0
ip netns exec ns0 ip addr add fc00💯:1/96 dev veth0
if [ "$1" == "v1" ]; then
ip netns exec ns0 \
ip link add dev ip6erspan00 type ip6erspan seq key 102 \
local fc00💯:1 remote fc00💯:2 \
erspan 123 erspan_ver 1
else
ip netns exec ns0 \
ip link add dev ip6erspan00 type ip6erspan seq key 102 \
local fc00💯:1 remote fc00💯:2 \
erspan_ver 2 erspan_dir 1 erspan_hwid 7
fi
ip netns exec ns0 ip addr add dev ip6erspan00 fc00:200::1/96
ip netns exec ns0 ip addr add dev ip6erspan00 10.10.200.1/24
ip link set dev veth1 up
ip link set dev ip6erspan11 up
ip netns exec ns0 ip link set dev ip6erspan00 up
ip netns exec ns0 ip link set dev veth0 up
}
main $1
ping6 -c 1 fc00💯:1 || true
ping -c 3 10.10.200.1
exit 0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the existing tests for ipv4 ipv6 erspan version 2.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to support for ipv4 erspan, this patch adds
erspan v2 to ip6erspan tunnel.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds support for erspan version 2. Not all features are
supported in this patch. The SGT (security group tag), GRA (timestamp
granularity), FT (frame type) are set to fixed value. Only hardware
ID and direction are configurable. Optional subheader is also not
supported.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch refactors the existing erspan implementation in order
to support erspan version 2, which has additional metadata. So, in
stead of having one 'struct erspanhdr' holding erspan version 1,
breaks it into 'struct erspan_base_hdr' and 'struct erspan_metadata'.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
nfp: ethtool flash updates
Dirk says:
This series adds the ability to update the control FW with ethtool.
It should be noted that the locking scheme here is to release the RTNL
lock before the flashing operation and to take it again afterwards to
ensure consistent state from the core code point of view. In this time,
we take a reference to the device to prevent the device being freed
while its being flashed.
This provides protection for the device being flashed while at the same
time not holding up any networking related functions which would
otherwise be locked out due to RTNL being held.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware flashing takes around 60s (specified to not take more than
70s). Prevent hogging the RTNL lock in this time and make use of the
longer timeout for the NSP command. The timeout is set to 2.5 * 70
seconds.
We only allow flashing the firmware from reprs or PF netdevs. VFs do not
have an app reference.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware flashing NSP operation takes longer to execute than the
current default timeout. We need a mechanism to set a longer timeout for
some commands. This patch adds the infrastructure to this.
The default timeout is still 30 seconds.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar says:
====================
ipvlan: packet scrub
While crossing namespace boundary IPvlan aggressively scrubs packets.
This is creating problems. First thing is that scrubbing changes the
packet type in skb meta-data to PACKET_HOST. This causes erroneous
packet delivery when dev_forward_skb() has already marked the packet
type as OTHER_HOST.
On the egress side scrubbing just before calling dev_queue_xmit()
creates another set of problems. Scrubbing remove skb->sk so the
prio update gets missed and more seriously, socket back-pressure
fails making TSQ not function correctly.
The first patch in the series just reverts the earlier change which
was adding a mac-check, but that is unnecessary if packet_type that
dev_forward_skb() has set is honored. The second path removes two of
the scrubs which are causing problems described above.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
IPvlan currently scrubs packets at every location where packets may be
crossing namespace boundary. Though this is desirable, currently IPvlan
does it more than necessary. e.g. packets that are going to take
dev_forward_skb() path will get scrubbed so no point in scrubbing them
before forwarding. Another side-effect of scrubbing is that pkt-type gets
set to PACKET_HOST which overrides what was already been set by the
earlier path making erroneous delivery of the packets.
Also scrubbing packets just before calling dev_queue_xmit() has detrimental
effects since packets lose skb->sk and because of that miss prio updates,
incorrect socket back-pressure and would even break TSQ.
Fixes: b93dd49c1a ('ipvlan: Scrub skb before crossing the namespace boundary')
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 92ff426450.
Even though the check added is not that taxing, it's not really needed.
First of all this will be per packet cost and second thing is that the
eth_type_trans() already does this correctly. The excessive scrubbing
in IPvlan was changing the pkt-type skb metadata of the packet which
made it necessary to re-check the mac. The subsequent patch in this
series removes the faulty packet-scrub.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_complete_tx_timestamp must ingest the skb it is passed. Call
kfree_skb if the skb cannot be enqueued.
Fixes: b245be1f4d ("net-timestamp: no-payload only sysctl")
Fixes: 9ac25fc063 ("net: fix socket refcounting in skb_complete_tx_timestamp()")
Reported-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: fixes 2017-12-13
some more patches for 4.15, that fix multiple issues with IP Takeover
configuration in qeth.
Please queue them up for stable kernels as well (4.9 and newer).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Any modification to the takeover IP-ranges requires that we re-evaluate
which IP addresses are takeover-eligible. Otherwise we might do takeover
for some addresses when we no longer should, or vice-versa.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modifying the flags of an IP addr object needs to be protected against
eg. concurrent removal of the same object from the IP table.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When takeover is switched off, current code clears the 'TAKEOVER' flag on
all IPs. But the flag is also used for RXIP addresses, and those should
not be affected by the takeover mode.
Fix the behaviour by consistenly applying takover logic to NORMAL
addresses only.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just as for an explicit enable/disable, toggling the takeover mode also
requires that the IP addresses get updated. Otherwise all IPs that were
added to the table before the mode-toggle, get registered with the old
settings.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9de52a755c ("arm64: fpsimd: Fix failure to restore FPSIMD
state after signals") fixed an issue reported in our FPSIMD signal
restore code but inadvertently introduced another issue which tends to
manifest as random SEGVs in userspace.
The problem is that when we copy the struct fpsimd_state from the kernel
stack (populated from the signal frame) into the struct held in the
current thread_struct, we blindly copy uninitialised stack into the
"cpu" field, which means that context-switching of the FP registers is
no longer reliable.
This patch fixes the problem by copying only the user_fpsimd member of
struct fpsimd_state. We should really rework the function prototypes
to take struct user_fpsimd_state * instead, but let's just get this
fixed for now.
Cc: Dave Martin <Dave.Martin@arm.com>
Fixes: 9de52a755c ("arm64: fpsimd: Fix failure to restore FPSIMD state after signals")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-12-15
1) Currently we can add or update socket policies, but
not clear them. Support clearing of socket policies
too. From Lorenzo Colitti.
2) Add documentation for the xfrm device offload api.
From Shannon Nelson.
3) Fix IPsec extended sequence numbers (ESN) for
IPsec offloading. From Yossef Efraim.
4) xfrm_dev_state_add function returns success even for
unsupported options, fix this to fail in such cases.
From Yossef Efraim.
5) Remove a redundant xfrm_state assignment.
From Aviv Heller.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- Initialize the fragment headers, by Sven Eckelmann
- Fix a NULL check in BATMAN V, by Sven Eckelmann
- Fix kernel doc for the time_setup() change, by Sven Eckelmann
- Use the right lock in BATMAN IV OGM Update, by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----
iQJKBAABCgA0FiEE1ilQI7G+y+fdhnrfoSvjmEKSnqEFAlozsZQWHHN3QHNpbW9u
d3VuZGVybGljaC5kZQAKCRChK+OYQpKeoZ1uD/94DURJf4b8kgUDjgMfuKZZyafH
c4N8SI+3+gZExtgXbb48f91a9S5T7qIAm46c7nHNJpTLEhc/ucup3c06i8VjBc2r
Tz37jnnjrHzfbw0p10zpLkdDlU0mLtEQBpNGQxru8h2x3gs2RBfDy/yX7MzzAp4m
maZ3ub0wPAtlRKQ4OywTStP9ZP7BXj4/puCRrn3kPIKDc1Ahwh4dS4r4euSvvR6z
2Qkfnpb3sbzh1Sa526GNAwgEo6hpssOugQyCIZUK4YJh1OfjnS+xJHWmfBkLw7q9
OfkuwAjkZMivrcxK/lvdMJ6WltQUyWVkKxDuA6iAtwRV4tX5W5b+9OEToZlHuPid
11bDXDfmWTfnpYM7uTT7tRbjFpvJ9X4ftUNHHtlL+h+VRz8Uf0xcteBIi7FxHHm5
fRqMLj5J0WU5rVf2vKTz2XIi5dXWgy/bkoPzalMc8UxWVsKthr34UZmcPRDVvCja
bwad1H+EEelx4tvPeWTEEhdhLFvalmfgRG3i/paqr547ETllmO462kdUTOmxDnvT
76GZVsLeHBPrnZi/tqc230EyoZijiM/l41twOZPjb0cklvOEFYR0vs/BUfmvdM/3
xlUF+CBaVnHcY3HDn7ywVICWP6jnG+LOQ4tOL6jjsKiqbEpPHRHuQ++MnZ2uRUgs
5e/yBVxdEjo9RoLVsg==
=US7g
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20171215' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- Initialize the fragment headers, by Sven Eckelmann
- Fix a NULL check in BATMAN V, by Sven Eckelmann
- Fix kernel doc for the time_setup() change, by Sven Eckelmann
- Use the right lock in BATMAN IV OGM Update, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the compatible string and Device Tree binding document for
7278B0.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Salil Mehta says:
====================
Hisilicon Network Subsystem 3 VF Ethernet Driver
This patch-set contains the support of the HNS3 (Hisilicon Network Subsystem 3)
Virtual Function Ethernet driver for hip08 family of SoCs. The Physical Function
driver is already part of the Linux mainline.
This VF driver has its Hardware Compatibility Layer and has commom/unified ENET
layer/client/ethtool code with the PF driver. It also has support of mailbox to
communicate with the HNS3 PF driver. The basic architecture of VF driver is
derivative of the PF driver. Just like PF driver, this driver is also PCI
Express based.
This driver is the ongoing development work and HNS3 VF Ethernet driver would be
incrementally enhanced with more new features.
High Level Architecture:
[ Ethtool ]
|
[ Ethernet Client ] ... [ RoCE Client ]
| |
[ HNAE Device ] |________
| | |
--------------------------------------------- |
|
[ HNAE3 Framework (Register/unregister) ] |
|
--------------------------------------------- |
| |
[ VF HCLGE Layer ] |
| | |
| | |
| | |
| [ VF Mailbox (To PF via IMP) ] |
| | |
[ IMP command Interface ] [ IMP command Interface ]
| |
| |
(A B O V E R U N S O N G U E S T S Y S T E M)
-------------------------------------------------------------
Q E M U / V F I O / K V M (on Host System)
-------------------------------------------------------------
HIP08 H A R D W A R E (limited to VF by SMMU)
[ IMP/Mgmt Processor (hardware common to system/cmd based) ]
Fig 1. HNS3 Virtual Function Driver
[ dcbnl ] [ Ethtool ]
| |
[ Ethernet Client ] [ ODP/UIO Client ] . . .[ RoCE Client ]
|_____________________| |
| _________|
[ HNAE Device ] | |
| | |
--------------------------------------------- |
|
[ HNAE3 Framework (Register/unregister) ] |
|
--------------------------------------------- |
| |
[ HCLGE Layer ] |
________________|_________________ |
| | | |
[ DCB ] | | |
| | | |
[ Scheduler/Shaper ] [ MDIO ] [ PF Mailbox ] |
| | | |
|________________|_________________| |
| |
[ IMP command Interface ] [ IMP command Interface ]
----------------------------------------------------------------
HIP08 H A R D W A R E
[ IMP/Mgmt Processor (hardware common to system/cmd based) ]
Fig 2. Existing HNS3 PF Driver (added with mailbox)
Change Log Summary:
Patch V4: Addressed SPDX related comment by Philippe Ombredanne
Patch V3: Addressed SPDX change requested by Philippe Ombredanne
Patch V2: 1. Addressed some comments by David Miller.
2. Addressed some internal comments on various patches
Patch V1: Initial Submit
====================
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All PF mailbox events are conveyed through a common interrupt
(vector 0). This interrupt vector is shared by reset and mailbox.
This patch adds the handling of mailbox interrupt event and its
deferred processing in context to a separate mailbox task.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is required to support ring-vector binding and reset
of TQPs requested by the VF driver to the PF driver. Mailbox
handler is added with corresponding VF commands/messages to
handle the request.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Command queue provides the provision of Mailbox command which
can be used for communication between PF and VF. PF handles
messages from various VFs for fetching various information like,
queue, vlan, link status related etc. It also handles the request
from various VFs to perform certain privileged operations.
This patch adds the support of a message handler for handling
such various command requests from VF.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the NAPI handling interface, skb buffer management,
management of the RX/TX descriptors, ethool interface etc.
has quite a bit of code which is common to VF and PF driver.
This patch makes the exisitng PF's HNS3 ENET driver as the
common ENET driver for both Virtual & Physical Function. This
will help in reduction of redundancy and better management of
code.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the new Makefiles and updates existing
Makefiles required to build the HNS3 Virtual Function driver.
This also updates the Kconfig for introduction of new menuconfig
entries related to VF driver.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of hardware compatibiltiy layer to the
HNS3 VF Driver. This layer implements various {set|get} operations
over MAC address for a virtual port, RSS related configuration,
fetches the link status info from PF, does various VLAN related
configuration over the virtual port, queries the statistics from
the hardware etc.
This layer can directly interact with hardware through the
IMP(Integrated Mangement Processor) interface or can use mailbox
to interact with the PF driver.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of the mailbox to the VF driver. The
mailbox shall be used as an interface to communicate with the
PF driver for various purposes like {set|get} MAC related
operations, reset, link status etc. The mailbox supports both
synchronous and asynchronous command send to PF driver.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of command interface for communication with
the IMP(Integrated Management Processor) for HNS3 Virtual Function
Driver.
Each VF has support of CQP(Command Queue Pair) ring interface.
Each CQP consis of send queue CSQ and receive queue CRQ.
There are various commands a VF may support, like to query frimware
version, TQP management, statistics, interrupt related, mailbox etc.
This also contains code to initialize the command queue, manage the
command queue descriptors and Rx/Tx protocol with the command processor
in the form of various commands/results and acknowledgements.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Learning is currently enabled for ports which are OVS slaves -
even though OVS doesn't need this indication.
Since we're not associating a fid with the port, HW would continuously
notify driver of learned [& aged] MACs which would be logged as errors.
Fixes: 2b94e58df5 ("mlxsw: spectrum: Allow ports to work under OVS master")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Wang says:
====================
add VLAN support to DSA MT7530
Changes sicne v2:
update to the latest code base from net-next and fix up all building
errors with -Werror.
Changes since v1:
- fix up the typo
- prefer ordering declarations longest to shortest
- update that vlan_prepare callback should not change any state
- use lower case letter for function naming
The patchset extends DSA MT7530 to VLAN support through filling required
callbacks in patch 1 and merging the special tag with VLAN tag in patch 2
for allowing that the hardware can handle these packets with VID from the
CPU port.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>