Retrieve and print retry_rd_err_log registers like the earlier change:
commit e80634a75a ("EDAC, skx: Retrieve and print retry_rd_err_log registers")
This is a little trickier than on Skylake because of potential
interference with BIOS use of the same registers. The default
behavior is to ignore these registers.
A module parameter retry_rd_err_log(default=0) controls the mode of operation:
- 0=off : Default.
- 1=bios : Linux doesn't reset any control bits, but just reports values.
This is "no harm" mode, but it may miss reporting some data.
- 2=linux: Linux tries to take control and resets mode bits,
clears valid/UC bits after reading. This should be
more reliable (especially if BIOS interference is reduced
by disabling eMCA reporting mode in BIOS setup).
Co-developed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210818175701.1611513-3-tony.luck@intel.com
MCDDRCFG is a per-channel register and uses bit{0,1} to indicate
the NVDIMM presence on DIMM slot{0,1}. Current i10nm_edac driver
wrongly uses MCDDRCFG as per-DIMM register and fails to detect
the NVDIMM.
Fix it by reading MCDDRCFG as per-channel register and using its
bit{0,1} to check whether the NVDIMM is populated on DIMM slot{0,1}.
Fixes: d4dc89d069 ("EDAC, i10nm: Add a driver for Intel 10nm server processors")
Reported-by: Fan Du <fan.du@intel.com>
Tested-by: Wen Jin <wen.jin@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210818175701.1611513-2-tony.luck@intel.com
There's little to no point in loading an EDAC driver running in a guest:
1) The CPU model reported by CPUID may not represent actual h/w
2) The hypervisor likely does not pass in access to memory controller devices
3) Hypervisors generally do not pass corrected error details to guests
Add a check in each of the Intel EDAC drivers for X86_FEATURE_HYPERVISOR
and simply return -ENODEV in the init routine.
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210615174419.GA1087688@agluck-desk2.amr.corp.intel.com
A future Xeon processor will include in-package HBM (high bandwidth
memory). The in-package HBM memory controller shares the same
architecture with the regular DDR memory controller.
Add the HBM memory controller devices for EDAC support.
Tested-by: Hongyu Ning <hongyu.ning@linux.intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210611170123.1057025-4-tony.luck@intel.com
Current i10nm_edac driver is only for system configured in 1-level
memory. If the system is configured in 2-level memory, the driver
doesn't report the 1st level memory DIMM for the error address, even
if the error occurs in the 1st level memory.
Both Ice Lake servers and Sapphire Rapids servers can be configured
in 2-level memory. Add detection of memory levels to i10nm_edac for
the two kinds of servers so that the driver can report the 2nd level
memory DIMM or the 1st level memory DIMM according to error source.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210611170123.1057025-3-tony.luck@intel.com
The Sapphire Rapids CPU model shares the same memory controller
architecture with Ice Lake server. There are some configurations
different from Ice Lake server as below:
- The device ID for configuration agent.
- The size for per channel memory-mapped I/O.
- The DDR5 memory support.
So add the above configurations and the Sapphire Rapids CPU model
ID for EDAC support.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Instead of raw access, use readl() to access MMIO registers of
memory controller to avoid possible compiler re-ordering.
Fixes: d4dc89d069 ("EDAC, i10nm: Add a driver for Intel 10nm server processors")
Cc: <stable@vger.kernel.org>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Use the X86_MATCH_INTEL_FAM6_MODEL_STEPPINGS() macro to pass CPU
stepping specific configurations to {skx,i10nm}_init(), so can delete
the CPU stepping check from 10nm_init().
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20200509010822.76331-1-qiuxu.zhuo@intel.com
The skx_edac driver wrongly uses the mtr register to retrieve two fields
close_pg and bank_xor_enable. Fix it by using the correct mcmtr register
to get the two fields.
Cc: <stable@vger.kernel.org>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Reported-by: Matthew Riley <mattdr@google.com>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20200515210146.1337-1-tony.luck@intel.com
The i10nm_edac driver failed to load on Ice Lake and Tremont/Jacobsville
servers if their CPU stepping >= 4 and failed on Ice Lake-D servers from
stepping 0. The root cause was that for Ice Lake and Tremont/Jacobsville
servers with CPU stepping >=4, the offset for bus number configuration
register was updated from 0xcc to 0xd0. For Ice Lake-D servers, all the
steppings use the updated 0xd0 offset.
Fix the issue by using the appropriate offset for bus number
configuration register according to the CPU model number and stepping.
Reported-by: Jerry Chen <jerry.t.chen@intel.com>
Reported-and-tested-by: Jin Wen <wen.jin@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/linux-edac/20200427084022.GC11036@zn.tnic
The device ID for configuration agent PCI device and the offset for
bus number configuration register can be CPU model specific. So add
a new structure res_config to make them configurable and pass res_config
to {skx,i10nm}_init() and skx_get_all_bus_mappings() for use.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20200427083246.GB11036@zn.tnic
The new macro set has a consistent namespace and uses C99 initializers
instead of the grufty C89 ones.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20200320131509.673579000@linutronix.de
The EDAC_DIMM_PTR() macro takes 3 arguments from struct mem_ctl_info.
Clean up this interface to only pass the mci struct and replace this
macro with a new function edac_get_dimm().
Also introduce an edac_get_dimm_by_index() function for later use.
This allows it to get a DIMM pointer only by a given index. This can
be useful if the DIMM's position within the layers of the memory
controller or the exact size of the layers are unknown.
Small style changes made for some hunks after applying the semantic
patch.
Semantic patch used:
@@ expression mci, a, b,c; @@
-EDAC_DIMM_PTR(mci->layers, mci->dimms, mci->n_layers, a, b, c)
+edac_get_dimm(mci, a, b, c)
[ bp: Touchups. ]
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Jason Baron <jbaron@akamai.com>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20191106093239.25517-2-rrichter@marvell.com
Currently big microservers have _XEON_D while small microservers have
_X, Make it uniformly: _D.
for i in `git grep -l "\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*_\(X\|XEON_D\)"`
do
sed -i -e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*ATOM.*\)_X/\1_D/g' \
-e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*\)_XEON_D/\1_D/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: x86@kernel.org
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Link: https://lkml.kernel.org/r/20190827195122.677152989@infradead.org
The source ID register offset for Skylake server is 0xf0, while for
Icelake server is 0xf8. Pass the correct offset to get the source ID.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The i10nm_edac only checks the ECC enabling status for the first
channel of the memory controller. If there aren't memory DIMMs
populated on the first channel, but at least one DIMM populated
on the second channel, it will wrongly report that the ECC for
the memory controller is disabled that fails to load the i10nm_edac
driver. Fix it by checking ECC enabling status per channel.
[Tony: Also report which channel has ECC disabled]
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Two new CPU models share the same memory controller
architecture with Jacobsville/Tremont, so can use the
same i10nm EDAC driver.
Add ICX and ICX-D CPU model numbers for EDAC support.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The following Kconfig constellations fail randconfig builds:
CONFIG_ACPI_NFIT=y
CONFIG_EDAC_DEBUG=y
CONFIG_EDAC_SKX=m
CONFIG_EDAC_I10NM=y
or
CONFIG_ACPI_NFIT=y
CONFIG_EDAC_DEBUG=y
CONFIG_EDAC_SKX=y
CONFIG_EDAC_I10NM=m
with:
...
CC [M] drivers/edac/skx_common.o
...
.../skx_common.o:.../skx_common.c:672: undefined reference to `__this_module'
That is because if one of the two drivers - skx_edac or i10nm_edac - is
built-in and the other one is a module, the shared file skx_common.c
gets linked into a module object by kbuild. Therefore, when linking that
same file into vmlinux, the '__this_module' symbol used in debugfs isn't
defined, leading to the above error.
Fix it by moving all debugfs code from skx_common.c to both skx_base.c
and i10nm_base.c respectively. Thus, skx_common.c doesn't refer to the
'__this_module' symbol anymore.
Clarify skx_common.c's purpose at the top of the file for future
reference, while at it.
[ bp: Make text more readable. ]
Fixes: d4dc89d069 ("EDAC, i10nm: Add a driver for Intel 10nm server processors")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190321221339.GA32323@agluck-desk
This driver supports the Intel 10nm series server integrated memory
controller. It gets the memory capacity and topology information by
reading the registers in PCI configuration space and memory-mapped I/O.
It decodes the memory error address to the platform specific address
by using the ACPI Address Translation (ADXL) Device Specific Method
(DSM).
Co-developed-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190130191519.15393-5-tony.luck@intel.com
Youquan Song
Qiuxu Zhuo
Luck, Tony
Borislav Petkov
Thomas Gleixner
Robert Richter
Peter Zijlstra