We want to remove the use of pm_runtime_irq_safe() from serial drivers
to allow making PM runtime handling generic. Let's simplify things by
disabling PM runtime autoidle for omap-serial as this driver has been
deprecated for years because of the 8250_omap driver.
There are still some omap-serial users that seem to hang on to it for
some unknown rs485 reasons it seems. But presumably those folks do not
need PM runtime autoidle with omap-serial, and hopefully can just move
to using 8250_omap driver instead.
For 8250_omap driver, we will eventually move to use generic serial
layer PM based on patches done by Andy Shevchenko to remove
pm_runtime_irq_safe() usage.
Cc: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: Dario Binacchi <dariobin@libero.it>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103149.51175-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to initialise irq-flags variables before saving the
interrupt state.
Drop the redundant initialisations from drivers that got this wrong.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210519092541.10137-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Data received during half-duplex transmission must be filtered.
If the target device responds quickly, emptying the FIFO at the end of
the transmission can erase not only the echo characters but also part of
the response message.
By keeping the receive interrupt enabled even during transmission, it
allows you to filter each echo character and only in a number equal to
those transmitted.
The issue was generated by a target device that started responding
240us later having received a request in communication at 115200bps.
Sometimes, some messages received by the target were missing some of the
first bytes.
Fixes: 3a13884abe ("tty/serial: omap: empty the RX FIFO at the end of half-duplex TX")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20210418094705.27014-1-dariobin@libero.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are rs485 transceivers (e.g. MAX13487E/MAX13488E) which
automatically disable or enable the driver and receiver to keep the bus
in the correct state.
In these cases we don't need a GPIO for flow control.
Fixes: 4a0ac0f55b ("OMAP: add RS485 support")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20210415210945.25863-1-dariobin@libero.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're about to amend uart_get_rs485_mode() to support a GPIO pin for
rs485 bus termination. Retrieving the GPIO descriptor may fail, so
allow uart_get_rs485_mode() to return an errno and change all callers
to check for failure.
The GPIO descriptor is going to be stored in struct uart_port. Pass
that struct to uart_get_rs485_mode() in lieu of a struct device and
struct serial_rs485, both of which are directly accessible from struct
uart_port.
A few drivers call uart_get_rs485_mode() before setting the struct
device pointer in struct uart_port. Shuffle those calls around where
necessary.
[Heiko Stuebner did the ar933x_uart.c portion, hence his Signed-off-by.]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/271e814af4b0db3bffbbb74abf2b46b75add4516.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the OMAP serial driver to use a GPIO descriptor
for the optional RTS signal.
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200415183927.269445-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and some
vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXoHT8w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl3CwCgj/97IKb4K49nV2rDgiV+t/ELWqUAnjBp+Zpd
H2BEdhwCFhq/5CJHKXWH
=JTm1
-----END PGP SIGNATURE-----
Merge tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and
some vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues"
* tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (161 commits)
serial: 8250: Optimize irq enable after console write
serial: 8250: Fix rs485 delay after console write
vt: vt_ioctl: fix use-after-free in vt_in_use()
vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console
tty: serial: make SERIAL_SPRD depend on COMMON_CLK
tty: serial: fsl_lpuart: fix return value checking
tty: serial: fsl_lpuart: move dma_request_chan()
ARM: dts: tango4: Make /serial compatible with ns16550a
ARM: dts: mmp*: Make the serial ports compatible with xscale-uart
ARM: dts: mmp*: Fix serial port names
ARM: dts: mmp2-brownstone: Don't redeclare phandle references
ARM: dts: pxa*: Make the serial ports compatible with xscale-uart
ARM: dts: pxa*: Fix serial port names
ARM: dts: pxa*: Don't redeclare phandle references
serial: omap: drop unused dt-bindings header
serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs
serial: 8250: 8250_omap: Work around errata causing spurious IRQs with DMA
serial: 8250: 8250_omap: Extend driver data to pass FIFO trigger info
serial: 8250: 8250_omap: Move locking out from __dma_rx_do_complete()
serial: 8250: 8250_omap: Account for data in flight during DMA teardown
...
The definitons in the dt-binding's gpio header only contains some
constants to be used in device trees. It is not relevant for omap-serial
(as the gpio API hides the details) and in fact unused so it can just be
dropped.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20200321204031.30369-1-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call cpu_latency_qos_add/update/remove_request() instead of
pm_qos_add/update/remove_request(), respectively, because the
latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
First, rename PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE to
PM_QOS_CPU_LATENCY_DEFAULT_VALUE and update all of the code
referring to it accordingly.
Next, rename cpu_dma_constraints to cpu_latency_constraints, move
the definition of it closer to the functions referring to it and
update all of them accordingly. [While at it, add a comment to mark
the start of the code related to the CPU latency QoS.]
Finally, rename the pm_qos_power_*() family of functions and
pm_qos_power_fops to cpu_latency_qos_*() and cpu_latency_qos_fops,
respectively, and update the definition of cpu_latency_qos_miscdev.
[While at it, update the miscdev interface code start comment.]
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-29-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following warning:
drivers/tty/serial/omap-serial.c: In function serial_omap_rlsi:
drivers/tty/serial/omap-serial.c:496:16: warning: variable ch set but not used [-Wunused-but-set-variable]
The character read is useless according to the table 23-246 of the omap4
TRM. So we can drop it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/1575617863-32484-1-git-send-email-wangxiongfeng2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rs485 flag "SER_RS485_RTS_AFTER_SEND" was wrongly read from the GPIO
flags. This caused the RTS pin to be high during boot.
Signed-off-by: Rafael Gago Castano <rgc@hms.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a driver invokes the uart_get_rs485_mode() helper, set the RTS
polarity to active high by default unless the newly introduced
"rs485-rts-active-low" property was specified.
imx contains a line to set the default RTS polarity to active high,
it is now superfluous and hence deleted.
omap-serial historically defaults to active low and supports an
"rs485-rts-active-high" property to inverse the polarity.
Retain that behavior for compatibility.
Cc: Mark Jackson <mpfj@newflow.co.uk>
Cc: Michał Oleszczyk <oleszczyk.m@gmail.com>
Cc: Rafael Gago Castano <rgc@hms.se>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ef838a81dd ("serial: Add common rs485 device tree parsing
function") consolidated retrieval of rs485 OF properties in a common
helper function but did not #ifdef it to CONFIG_OF. The function is
therefore included on ACPI platforms as well even though it's not used.
On the other hand ACPI platforms with rs485 do exist (e.g. Siemens
IOT2040) and they may leverage _DSD to store rs485 properties. Likewise,
UART platform devices instantiated from an MFD should be able to specify
rs485 properties. In fact, the tty subsystem maintainer had asked for
a "generic" function during review of commit ef838a81dd4d:
https://marc.info/?l=linux-serial&m=150143441725194&w=4
Thus, instead of constraining the helper to OF platforms, make it
platform-agnostic by converting it to device_property_*() functions
and renaming it accordingly.
In imx.c, move the invocation of uart_get_rs485_mode() from
serial_imx_probe_dt() to serial_imx_probe() so that it also gets called
for non-OF devices.
In omap-serial.c, move its invocation further up within
serial_omap_probe_rs485() so that the RTS polarity can be overridden
with the driver-specific "rs485-rts-active-high" property once we
introduce a generic "rs485-rts-active-low" property.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all tty files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/tty files files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 348f9bb31c ("serial: omap: Fix RTS handling") sought to enable
auto RTS upon manual RTS assertion and disable it on deassertion.
However it seems the latter was done incorrectly, it clears all bits in
the Extended Features Register *except* auto RTS.
Fixes: 348f9bb31c ("serial: omap: Fix RTS handling")
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The do .. while loop checks for interrupt pending at the
start of the loop and exits if there is none, it then
checks again for this condition at the end of the loop.
Signed-off-by: Martin Townsend <mtownsend1973@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We just got a common helper for parsing the rs485 specific
device tree properties. Use it and drop the open coded parser.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlycon would be alive outside the init code in these cases:
1/ we have keep_bootcon in cmdline.
2/ we don't have a real console to switch to.
So remove the __init marking to avoid invalid memory access.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to actually suspend the device before returning after a failed
(or deferred) probe.
Note that autosuspend must be disabled before runtime pm is disabled in
order to balance the usage count due to a negative autosuspend delay as
well as to make the final put suspend the device synchronously.
Fixes: 388bc26226 ("omap-serial: Fix the error handling in the omap_serial probe")
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An unbalanced and misplaced synchronous put was used to suspend the
device on driver unbind, something which with a likewise misplaced
pm_runtime_disable leads to external aborts when an open port is being
removed.
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa024010
...
[<c046e760>] (serial_omap_set_mctrl) from [<c046a064>] (uart_update_mctrl+0x50/0x60)
[<c046a064>] (uart_update_mctrl) from [<c046a400>] (uart_shutdown+0xbc/0x138)
[<c046a400>] (uart_shutdown) from [<c046bd2c>] (uart_hangup+0x94/0x190)
[<c046bd2c>] (uart_hangup) from [<c045b760>] (__tty_hangup+0x404/0x41c)
[<c045b760>] (__tty_hangup) from [<c045b794>] (tty_vhangup+0x1c/0x20)
[<c045b794>] (tty_vhangup) from [<c046ccc8>] (uart_remove_one_port+0xec/0x260)
[<c046ccc8>] (uart_remove_one_port) from [<c046ef4c>] (serial_omap_remove+0x40/0x60)
[<c046ef4c>] (serial_omap_remove) from [<c04845e8>] (platform_drv_remove+0x34/0x4c)
Fix this up by resuming the device before deregistering the port and by
suspending and disabling runtime pm only after the port has been
removed.
Also make sure to disable autosuspend before disabling runtime pm so
that the usage count is balanced and device actually suspended before
returning.
Note that due to a negative autosuspend delay being set in probe, the
unbalanced put would actually suspend the device on first driver unbind,
while rebinding and again unbinding would result in a negative
power.usage_count.
Fixes: 7e9c8e7dbf ("serial: omap: make sure to suspend device before remove")
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UPF_BOOT_AUTOCONF flag is needed for proper
flow control support.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add DT earlycon for omap_serial driver. This boot console is included
with CONFIG_SERIAL_EARLYCON=y, CONFIG_OF=y, CONFIG_SERIAL_OMAP=y, and
CONFIG_OF_EARLY_FLATTREE=y.
This boot console is enabled with the command line option "earlycon"
(without "=<name>...") when the DT 'stdout-path' property matches a
compatible uart.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DRIVER_NAME is too generic to be used in a driver-specific platform
data file. Use a name specific to the driver instead, to avoid
collisions.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wait_for_xmitr() function is only used if CONFIG_CONSOLE_POLL
or CONFIG_SERIAL_OMAP_CONSOLE are set, but when both are disabled,
the compiler warns about it being unused:
drivers/tty/serial/omap-serial.c:1168:13: warning: 'wait_for_xmitr' defined but not used [-Wunused-func
We could add more #ifdefs to work around it, but adding __maybe_unused
seems nicer.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 2172076d23 ("serial/omap-serial: Deinline wait_for_xmitr, save 165 bytes")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The omap-serial driver emulates RS485 delays using software timers,
but neglects to clamp the input values from the unprivileged
ioctl(TIOCSRS485). Because the software implementation busy-waits,
malicious userspace could stall the cpu for ~49 days.
Clamp the input values to < 100ms.
Fixes: 4a0ac0f55b ("OMAP: add RS485 support")
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They're used by only if CONFIG_PM is enabled, so enclose them
with proper ifdefs. Removes these warnings:
drivers/tty/serial/omap-serial.c:202:12: warning: 'serial_omap_get_context_loss_count' defined but not used [-Wunused-function]
drivers/tty/serial/omap-serial.c:213:13: warning: 'serial_omap_enable_wakeup' defined but not used [-Wunused-function]
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can now use generic wakeirq handling and remove the custom handling
for the wake-up interrupts.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is pm_qos_add_request() being executed on serial_omap_probe(),
which stores "&up->pm_qos_request" from omap-serial driver to
"pm_qos_array[PM_QOS_CPU_DMA_LATENCY]->constraints". If
serial_omap_probe() fails after pm_qos_add_request() (e.g. on
uart_add_one_port() call), pm_qos_array still keeping pm_qos_request
struct from omap-serial driver, which is not valid anymore (since driver
failed). This leads further to kernel crash on pm_qos_update_target(),
executing from some completely different driver.
We were observing this while trying to run audio playback while having
one of omap-serial driver instances failed on uart_add_one_port() call:
Unable to handle kernel paging request at virtual address fffffffc
Backtrace:
(plist_add) from (pm_qos_update_target)
(pm_qos_update_target) from (pm_qos_add_request)
(pm_qos_add_request) from (snd_pcm_hw_params)
(snd_pcm_hw_params) from (snd_pcm_common_ioctl1)
(snd_pcm_common_ioctl1) from (snd_pcm_playback_ioctl1)
(snd_pcm_playback_ioctl1) from (snd_pcm_playback_ioctl)
(snd_pcm_playback_ioctl) from (do_vfs_ioctl)
(do_vfs_ioctl) from (SyS_ioctl)
(SyS_ioctl) from (ret_fast_syscall)
This patch adds pm_qos_remove_request() on fail path in
serial_omap_probe() in order to fix this issue. While at it, free the
wakeup settings on fail path as well, just like it's done in
serial_omap_remove().
Signed-off-by: Semen Protsenko <semen.protsenko@globallogic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When wakeirq is not used/enabled, "no wakeirq for uart0" is output for
all TTY as the log message is generated before the port line is
initialized.
[ 0.802656] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.811700] omap_uart 44e09000.serial: no wakeirq for uart0
[ 0.812379] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a OMAP UART0
[ 1.503622] console [ttyO0] enabled
[ 1.509836] omap_uart 48022000.serial: no wakeirq for uart0
[ 1.516118] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89, base_baud = 3000000) is a OMAP UART1
[ 1.527711] omap_uart 48024000.serial: no wakeirq for uart0
[ 1.533881] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90, base_baud = 3000000) is a OMAP UART2
[ 1.545324] omap_uart 481a6000.serial: no wakeirq for uart0
[ 1.551410] 481a6000.serial: ttyO3 at MMIO 0x481a6000 (irq = 60, base_baud = 3000000) is a OMAP UART3
[ 1.562946] omap_uart 481a8000.serial: no wakeirq for uart0
[ 1.569036] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61, base_baud = 3000000) is a OMAP UART4
Fix by moving wakeirq initialization, check, and dev_info() call to
after port line initialization and validation.
Signed-off-by: Doug Kehn <rdkehn@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP UART ignores MCR[1] (ie., RTS) when in autoRTS mode. This
makes it impossible for either the serial core or userspace to
manually flow control the sender.
Disable autoRTS mode when RTS is lowered and restore the previous
mode when RTS is raised.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hw-assisted flow control support was added to the serial core
in v3.8 with commits,
dba05832cb ("SERIAL: core: add hardware assisted h/w flow control support")
2cbacafd7a ("SERIAL: core: add hardware assisted s/w flow control support")
9aba8d5b01 ("SERIAL: core: add throttle/unthrottle callbacks for hardware
assisted flow control")
Since then, additional requirements for serial core support have arisen.
Specifically,
1. Separate tx and rx flow control settings for UARTs which only support
tx flow control (ie., autoCTS).
2. Disable sw-assisted CTS flow control in autoCTS mode
3. Support for RTS flow control by serial core and userspace in autoRTS mode
Distinguish mode from capability; introduce UPSTAT_AUTORTS, UPSTAT_AUTOCTS
and UPSTAT_AUTOXOFF which, when set by the uart driver, enable serial core
support for hw-assisted rx, hw-assisted tx and hw-assisted in-band/IXOFF
rx flow control, respectively. [Note: hw-assisted in-band/IXON tx flow
control does not require serial core support/intervention and can be
enabled by the uart driver when required.]
These modes must be set/reset in the driver's set_termios() method, based
on termios settings, and thus can be safely queried in any context in which
one of the port lock, port mutex or termios rwsem are held. Set these modes
in the 2 in-tree drivers, omap-serial and 8250_omap, which currently
use UPF_HARD_FLOW/UPF_SOFT_FLOW support.
Retain UPF_HARD_FLOW and UPF_SOFT_FLOW as capabilities; re-define
UPF_HARD_FLOW as both UPF_AUTO_RTS and UPF_AUTO_CTS to allow for distinct
and separate rx and tx flow control capabilities.
Disable sw-assisted CTS flow control when UPSTAT_AUTOCTS is enabled.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fixes for omap-serial.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
index 18c30ca..f43ed2c 100644
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/tty/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter reported:
|drivers/tty/serial/8250/8250_omap.c:1025 omap8250_probe()
|warn: unsigned 'up.port.line' is never less than zero.
|1025 if (up.port.line < 0) {
Since of_alias_get_id() and pdev->id can get negative I check for the
error via ret variable.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce an homogeneous lock system between setting and using the rs485
data of the uart_port.
This patch should not be split into multiple ones in order to avoid
leaving the tree in an unstable state.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Suggested-by: Alan Cox <alan@linux.intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to unify all the rs485 ioctl handling
Use the implementation of TIOC[GS]RS485 ioctl handling on serial_core.
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This error message is not necessary. The driver core code will print all
probe error messages. It also resolves some error codes to proper error
messages. For example -EPROBE_DEFER will only be printed as an info message.
This patch removes the error message as the core prints the same
information.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To determine the correct divisor, we need to know the difference between
the desired baud rate and the actual baud rate. The calculation for this
difference is implemented twice within omap_serial_baud_is_mode16().
Pull out the calculation for easier maintenance.
While at it, remove the CamelCasing from the variable names.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the chosen baud rate is large enough (e.g. 3.5 megabaud), the
calculated n values in serial_omap_is_baud_mode16() may become 0. This
causes a division by zero when calculating the difference between
calculated and desired baud rates. To prevent this, cap the n13 and n16
values on 1.
Division by zero in kernel.
[<c00132e0>] (unwind_backtrace) from [<c00112ec>] (show_stack+0x10/0x14)
[<c00112ec>] (show_stack) from [<c01ed7bc>] (Ldiv0+0x8/0x10)
[<c01ed7bc>] (Ldiv0) from [<c023805c>] (serial_omap_baud_is_mode16+0x4c/0x68)
[<c023805c>] (serial_omap_baud_is_mode16) from [<c02396b4>] (serial_omap_set_termios+0x90/0x8d8)
[<c02396b4>] (serial_omap_set_termios) from [<c0230a0c>] (uart_change_speed+0xa4/0xa8)
[<c0230a0c>] (uart_change_speed) from [<c0231798>] (uart_set_termios+0xa0/0x1fc)
[<c0231798>] (uart_set_termios) from [<c022bb44>] (tty_set_termios+0x248/0x2c0)
[<c022bb44>] (tty_set_termios) from [<c022c17c>] (set_termios+0x248/0x29c)
[<c022c17c>] (set_termios) from [<c022c3e4>] (tty_mode_ioctl+0x1c8/0x4e8)
[<c022c3e4>] (tty_mode_ioctl) from [<c0227e70>] (tty_ioctl+0xa94/0xb18)
[<c0227e70>] (tty_ioctl) from [<c00cf45c>] (do_vfs_ioctl+0x4a0/0x560)
[<c00cf45c>] (do_vfs_ioctl) from [<c00cf568>] (SyS_ioctl+0x4c/0x74)
[<c00cf568>] (SyS_ioctl) from [<c000e480>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Lindgren
Johan Hovold
Dario Binacchi
Gustavo A. R. Silva
Lukas Wunner
Linus Walleij
Linus Torvalds
Uwe Kleine-König
Rafael J. Wysocki
Dmitry Safonov
Xiongfeng Wang
Rafael Gago
Greg Kroah-Hartman
Martin Townsend
Sascha Hauer
Jeffy Chen
Sebastian Reichel
Bhumika Goyal
Lokesh Vutla
Jean Delvare
Arnd Bergmann
Peter Hurley
Denys Vlasenko
Ezequiel Garcia
Semen Protsenko
Doug Kehn
Pavel Machek
Sebastian Andrzej Siewior
Ricardo Ribalda Delgado
Nishanth Menon
Markus Pargmann
Frans Klaver
Felipe Balbi