The config SENSORS_ASC7621 entry is inside an if HWMON / endif block,
so it already depends on HWMON.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This CPU family provides NB register values to gather following
TDP information
* ProcessorPwrWatts: Specifies in Watts the maximum amount of power
the processor can support.
* CurrPwrWatts: Specifies in Watts the current amount of power being
consumed by the processor.
This driver provides
* power1_crit (ProcessorPwrWatts)
* power1_input (CurrPwrWatts)
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
AMDs upcoming CPUs use the same mechanism for the internal
temperature reporting as the Fam10h CPUs, so we just needed to add
the appropriate PCI-ID to the list.
This allows to use the k10temp driver on those CPUs.
While at it change the Kconfig entry to be more generic.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
After the merge of pkgtemp functionality into the coretemp driver,
the pkgtemp driver is no longer necessary. Remove it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Add support for Analog Devices ADM1275 Hot-Swap Controller and Digital Power
Monitor
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Hardware monitoring support for TI UCD90120, UCD90124, UCD9090, and UCD90910
Sequencer and System Health Controllers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
This patch adds hardware monitoring support for TI UCD9220, UCD9222, UCD9224,
UCD9240, UCD9244, UCD9246, and UCD9248 Digital PWM System Controllers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
This patch adds hardware monitoring support for Maxim MAX16065, MAX16066,
MAX16067, MAX16068, MAX16070, and MAX16071 flash-configurable system managers
with nonvolatile fault registers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
MAX6642 is a SMBus-Compatible Remote/Local Temperature Sensor with
Overtemperature Alarm from Maxim.
Signed-off-by: Per Dalen <per.dalen@appeartv.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Recent Xeon processor thermal sensors are supported by the coretemp
driver and not the adm1021 driver. Only one old generation of Xeon
processors (the first Netburst ones) are supported by the adm1021
driver.
Reported-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds support for ADT7461A and NCT1008 to the lm90 driver.
Both chips have identical functionality and report the same manufacturing ID
and device ID values.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the Fintek F81865F. It's essentially compatible with
the F71882FG, but has fewer inputs: 7 voltage, 2 temperature and 2 fan
inputs only.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The list of supported devices was not always well documented in all
places. Clarify and list all devices in documentation, Kconfig and
the driver itself.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This driver exposes the sysfs nodes of the TWL4030 MADC module.
All the voltage channel values are expressed in terms of mV. Channel 13
and channel 14 are reserved. There are channels which represent
temperature and current the output is represented by celcius
and mA respectively.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
SMSC SCH5627 Super I/O chips include complete hardware monitoring
capabilities. They can monitor up to 5 voltages, 4 fans and 8
temperatures.
The hardware monitoring part of the SMSC SCH5627 is accessed by talking
through an embedded microcontroller. An application note describing the
protocol for communicating with the microcontroller is available upon
request. Please mail me if you want a copy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for detection of the National Semiconductor LM75A using the ID
register value.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The lis3lv02d drivers aren't hardware monitoring drivers, so the don't
belong to drivers/hwmon. Move them to drivers/misc, short of a better
home.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Tested-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Takashi Iwai <tiwai@suse.de>
The hp_accel driver isn't a hardware monitoring driver, so it doesn't
belong to drivers/hwmon. Move it to drivers/platform/x86, assuming HP
doesn't ship non-x86 laptops.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Tested-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Takashi Iwai <tiwai@suse.de>
The dependencies between the various lis3lv02d drivers make it
impossible to split them to different directories, while we really
want to do this. Move handling of dependencies from Makefile to
Kconfig, to make the move possible at all.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Tested-by: Eric Piel <eric.piel@tremplin-utc.net>
Tested-by: Takashi Iwai <tiwai@suse.de>
LTC4151 is High Voltage I2C Current and Voltage Monitor from Linear
Technology.
Signed-off-by: Per Dalen <per.dalen@appeartv.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This driver adds support for hardware monitoring features of various PMBus
devices.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
This patch adds support for hardware monitoring of Lineage Compact Power Line
Power Entry Modules.
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The interface is identical EMC6D102, so all that needs to be added are
some definitions and their uses.
Registers apparently missing in EMC6D103S/EMC6D103:A2 compared to EMC6D103:A0,
EMC6D103:A1, and EMC6D102 (according to the data sheets), but used
unconditionally in the driver: 62[5:7], 6D[0:7], and 6E[0:7]. For that
reason, EMC6D103S chips don't get enabled for the time being.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
(Guenter Roeck: Replaced EMC6D103_A2 with EMC6D103S per EMC6D103S datasheet)
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org
Add the PCI ID to support the internal temperature sensor of the
AMD "Llano" and "Brazos" processor families.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org # ca86828: x86, AMD, PCI: Add AMD northbridge PCI device
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The documentation lists standard numbers and chip names in excruciating
detail, but that's all it does. To help mere mortals in deciding
whether to enable this driver, mention what this sensor is for and in
which systems it might be found.
Also add a link to the actual JC 42.4 specification.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds basic support for LM94 to the LM93 driver. LM94 specific
sensors and features are not supported.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
EMC1423 uses the similar register and adds a hardware shutdown pin to
protect exceed temperature. This function is set by resistor; it's not
necessary to do anything in the driver except add the emc1423 pid of 0x23.
Signed-off-by: Jekyll Lai <jekyll_lai@wistron.com>
[Updated Kconfig/comments and minor further changes asked for by the hwmon
maintainers]
Signed-off-by: Alan Cox <alan@linux.intel.com>
[Fixed checkpatch warning]
Signed-of--by: Jean Delvare <khali@linux-fr.org>
Driver for Dallas Semiconductor DS620 temperature sensor and thermostat
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for the IT8721F/IT8758E. These new chips differ from the
older IT87xxF chips in the following ways:
* ADC LSB is 12 mV instead of 16 mV.
* PWM values are 8-bit instead of 7-bit.
There are other minor changes we don't have to care about in the
driver.
Another change is that we will handle internal voltage scaling in the
driver instead of delegating the work to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the dependency on EXPERIMENTAL for all drivers which are in
the kernel tree for a long time, are known to work properly and for
which we have documentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Juerg Haefliger <juergh@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The ams driver isn't a hardware monitoring driver, so it shouldn't
live under driver/hwmon. drivers/macintosh seems much more
appropriate, as the driver is only useful on PowerBooks and iBooks.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
The fan control feature of the w83795 driver is insufficiently
reviewed and tested for public consumption at this time, so make it
optional and disabled by default. We will change the default when
review and testing is deemed sufficient. Ultimately the option will
go away.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
There is still much work needed, but I wanted to give Wei the credit
he deserves. I've merged some of my own fixes already, to make
gcc and checkpatch happy. Individual fixes and improvements from me
will follow.
[JD: Fix build errors]
[JD: Coding style cleanups]
[JD: Get rid of forward declarations]
[JD: Drop VID support]
[JD: Drop fault output control feature]
[JD: Use lowercase for inline function names]
[JD: Use strict variants of the strtol/ul functions]
[JD: Shorten the read and write function names]
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This way we don't need to modify Kconfig every time a new SoC comes along to
make this driver support it. Also fix some typos while I'm at it.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I was wondering if that chip ever existed publicly... Apparently yes,
so add support for it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds hwmon support for fans connected to GPIO lines.
Platform specific information such as GPIO pinout and speed conversion array
(rpm from/to GPIO value) are passed to the driver via platform_data.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This driver adds support for Linear Technology LTC4261 I2C Negative
Voltage Hot Swap Controller.
Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The hdaps driver isn't a hardware monitoring driver, so it shouldn't
live under driver/hwmon. drivers/platform/x86 seems much more
appropriate, as the driver is only useful on x86 laptops.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Other than coretemp, from which this code was apparently derived, there
is no PCI specific code in this driver.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Hans de Goede
Jean Delvare
Andreas Herrmann
Andre Przywara
Guenter Roeck
Per Dalén
Keerthy
Dirk Eibach
Len Sorensen
stigge@antcom.de
Jan Beulich
Clemens Ladisch
Jekyll Lai
Urs Fleisch
Wei Song
Maurus Cuelenaere
Simon Guinot