Previously, I failed to realize that Kees' patch [1] has not been merged
into the mainline yet, and dropped DEBUG_INFO=y too eagerly from the
mainline. As the results, "make debug.config" won't be able to flip
DEBUG_INFO=n from the existing .config. This should close the gaps of a
few weeks before Kees' patch is there, and work regardless of their
merging status anyway.
Link: https://lore.kernel.org/all/20220125075126.891825-1-keescook@chromium.org/ [1]
Link: https://lkml.kernel.org/r/20220308153524.8618-1-quic_qiancai@quicinc.com
Signed-off-by: Qian Cai <quic_qiancai@quicinc.com>
Reported-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In our testing, a livelock task was found. Through sysrq printing, same
stack was found every time, as follows:
__swap_duplicate+0x58/0x1a0
swapcache_prepare+0x24/0x30
__read_swap_cache_async+0xac/0x220
read_swap_cache_async+0x58/0xa0
swapin_readahead+0x24c/0x628
do_swap_page+0x374/0x8a0
__handle_mm_fault+0x598/0xd60
handle_mm_fault+0x114/0x200
do_page_fault+0x148/0x4d0
do_translation_fault+0xb0/0xd4
do_mem_abort+0x50/0xb0
The reason for the livelock is that swapcache_prepare() always returns
EEXIST, indicating that SWAP_HAS_CACHE has not been cleared, so that it
cannot jump out of the loop. We suspect that the task that clears the
SWAP_HAS_CACHE flag never gets a chance to run. We try to lower the
priority of the task stuck in a livelock so that the task that clears
the SWAP_HAS_CACHE flag will run. The results show that the system
returns to normal after the priority is lowered.
In our testing, multiple real-time tasks are bound to the same core, and
the task in the livelock is the highest priority task of the core, so
the livelocked task cannot be preempted.
Although cond_resched() is used by __read_swap_cache_async, it is an
empty function in the preemptive system and cannot achieve the purpose
of releasing the CPU. A high-priority task cannot release the CPU
unless preempted by a higher-priority task. But when this task is
already the highest priority task on this core, other tasks will not be
able to be scheduled. So we think we should replace cond_resched() with
schedule_timeout_uninterruptible(1), schedule_timeout_interruptible will
call set_current_state first to set the task state, so the task will be
removed from the running queue, so as to achieve the purpose of giving
up the CPU and prevent it from running in kernel mode for too long.
(akpm: ugly hack becomes uglier. But it fixes the issue in a
backportable-to-stable fashion while we hopefully work on something
better)
Link: https://lkml.kernel.org/r/20220221111749.1928222-1-cgel.zte@gmail.com
Signed-off-by: Guo Ziliang <guo.ziliang@zte.com.cn>
Reported-by: Zeal Robot <zealci@zte.com.cn>
Reviewed-by: Ran Xiaokai <ran.xiaokai@zte.com.cn>
Reviewed-by: Jiang Xuexin <jiang.xuexin@zte.com.cn>
Reviewed-by: Yang Yang <yang.yang29@zte.com.cn>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Roger Quadros <rogerq@kernel.org>
Cc: Ziliang Guo <guo.ziliang@zte.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent commit 974578017f ("iavf: Add waiting so the port is
initialized in remove") adds a wait-loop at the beginning of
iavf_remove() to ensure that port initialization is finished
prior unregistering net device. This causes a regression
in reboot/shutdown scenario because in this case callback
iavf_shutdown() is called and this callback detaches the device,
makes it down if it is running and sets its state to __IAVF_REMOVE.
Later shutdown callback of associated PF driver (e.g. ice_shutdown)
is called. That callback calls among other things sriov_disable()
that calls indirectly iavf_remove() (see stack trace below).
As the adapter state is already __IAVF_REMOVE then the mentioned
loop is end-less and shutdown process hangs.
The patch fixes this by checking adapter's state at the beginning
of iavf_remove() and skips the rest of the function if the adapter
is already in remove state (shutdown is in progress).
Reproducer:
1. Create VF on PF driven by ice or i40e driver
2. Ensure that the VF is bound to iavf driver
3. Reboot
[52625.981294] sysrq: SysRq : Show Blocked State
[52625.988377] task:reboot state:D stack: 0 pid:17359 ppid: 1 f2
[52625.996732] Call Trace:
[52625.999187] __schedule+0x2d1/0x830
[52626.007400] schedule+0x35/0xa0
[52626.010545] schedule_hrtimeout_range_clock+0x83/0x100
[52626.020046] usleep_range+0x5b/0x80
[52626.023540] iavf_remove+0x63/0x5b0 [iavf]
[52626.027645] pci_device_remove+0x3b/0xc0
[52626.031572] device_release_driver_internal+0x103/0x1f0
[52626.036805] pci_stop_bus_device+0x72/0xa0
[52626.040904] pci_stop_and_remove_bus_device+0xe/0x20
[52626.045870] pci_iov_remove_virtfn+0xba/0x120
[52626.050232] sriov_disable+0x2f/0xe0
[52626.053813] ice_free_vfs+0x7c/0x340 [ice]
[52626.057946] ice_remove+0x220/0x240 [ice]
[52626.061967] ice_shutdown+0x16/0x50 [ice]
[52626.065987] pci_device_shutdown+0x34/0x60
[52626.070086] device_shutdown+0x165/0x1c5
[52626.074011] kernel_restart+0xe/0x30
[52626.077593] __do_sys_reboot+0x1d2/0x210
[52626.093815] do_syscall_64+0x5b/0x1a0
[52626.097483] entry_SYSCALL_64_after_hwframe+0x65/0xca
Fixes: 974578017f ("iavf: Add waiting so the port is initialized in remove")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://lore.kernel.org/r/20220317104524.2802848-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ACL rules can be offloaded to VCAP IS2 either through chain 0, or, since
the blamed commit, through a chain index whose number encodes a specific
PAG (Policy Action Group) and lookup number.
The chain number is translated through ocelot_chain_to_pag() into a PAG,
and through ocelot_chain_to_lookup() into a lookup number.
The problem with the blamed commit is that the above 2 functions don't
have special treatment for chain 0. So ocelot_chain_to_pag(0) returns
filter->pag = 224, which is in fact -32, but the "pag" field is an u8.
So we end up programming the hardware with VCAP IS2 entries having a PAG
of 224. But the way in which the PAG works is that it defines a subset
of VCAP IS2 filters which should match on a packet. The default PAG is
0, and previous VCAP IS1 rules (which we offload using 'goto') can
modify it. So basically, we are installing filters with a PAG on which
no packet will ever match. This is the hardware equivalent of adding
filters to a chain which has no 'goto' to it.
Restore the previous functionality by making ACL filters offloaded to
chain 0 go to PAG 0 and lookup number 0. The choice of PAG is clearly
correct, but the choice of lookup number isn't "as before" (which was to
leave the lookup a "don't care"). However, lookup 0 should be fine,
since even though there are ACL actions (policers) which have a
requirement to be used in a specific lookup, that lookup is 0.
Fixes: 226e9cd82a ("net: mscc: ocelot: only install TCAM entries into a specific lookup and PAG")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220316192117.2568261-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RXCHK block will return a partial checksum of 0 if it encounters
a problem while receiving a packet. Since a 1's complement sum can
only produce this result if no bits are set in the received data
stream it is fair to treat it as an invalid partial checksum and
not pass it up the stack.
Fixes: 8101553978 ("net: bcmgenet: use CHECKSUM_COMPLETE for NETIF_F_RXCSUM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220317012812.1313196-1-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit b7a49f7305 ("bnx2x: Utilize firmware 7.13.21.0")
added request_firmware() logic in probe() which caused
load failure when firmware file is not present in initrd (below),
as access to firmware file is not feasible during probe.
Direct firmware load for bnx2x/bnx2x-e2-7.13.15.0.fw failed with error -2
Direct firmware load for bnx2x/bnx2x-e2-7.13.21.0.fw failed with error -2
This patch fixes this issue by -
1. Removing request_firmware() logic from the probe()
such that .ndo_open() handle it as it used to handle
it earlier
2. Given request_firmware() is removed from probe(), so
driver has to relax FW version comparisons a bit against
the already loaded FW version (by some other PFs of same
adapter) to allow different compatible/close enough FWs with which
multiple PFs may run with (in different environments), as the
given PF who is in probe flow has no idea now with which firmware
file version it is going to initialize the device in ndo_open()
Link: https://lore.kernel.org/all/46f2d9d9-ae7f-b332-ddeb-b59802be2bab@molgen.mpg.de/
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: b7a49f7305 ("bnx2x: Utilize firmware 7.13.21.0")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220316214613.6884-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver requires firmware so define MODULE_FIRMWARE so that modinfo
provides the details.
Fixes: fa164e40c5 ("net: phy: mscc: split the driver into separate files")
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Link: https://lore.kernel.org/r/20220316151835.88765-1-juergh@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clang static analysis reports this representative issue
igb_ptp.c:997:3: warning: The left operand of '+' is a
garbage value
ktime_add_ns(shhwtstamps.hwtstamp, adjust);
^ ~~~~~~~~~~~~~~~~~~~~
shhwtstamps.hwtstamp is set by a call to
igb_ptp_systim_to_hwtstamp(). In the switch-statement
for the hw type, the hwtstamp is zeroed for matches
but not the default case. Move the memset out of
switch-statement. This degarbages the default case
and reduces the size.
Some whitespace cleanup of empty lines
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The calculation of the checksum can fail.
So move converting the checksum to little endian
to inside the return status check.
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
- bugfixes
- mbssid support for mt7915
- 6 GHz support for mt7915
- mt7921u driver
-----BEGIN PGP SIGNATURE-----
Comment: GPGTools - http://gpgtools.org
iF0EABECAB0WIQR10Rp9kadxD0kAQu/XfRQdAqdu9QUCYjJGDAAKCRDXfRQdAqdu
9SCmAJ0Uy6pWjbGm7z9qQGZjhE7FyrqQPQCggD0MIbXKQRQPGH7wLdoLmNaSYdg=
=LmRF
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2022-03-16' of https://github.com/nbd168/wireless
mt76 patches for 5.18
- bugfixes
- mbssid support for mt7915
- 6 GHz support for mt7915
- mt7921u driver
These function is used to stop transmitting when we are going to switch
channels or do some RF calibration. Before these operations, we need to
stop channel transmission and backup setting into parameter tx_en. After
operations are done, resume transmitting by backup parameter tx_en.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-13-pkshih@realtek.com
In order to support 8852C that uses 32 bits to control TX types.
This patch doesn't really use 32 bits tx_en yet, but next patch will
use it.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-12-pkshih@realtek.com
Use if() style would be clear than "? :", because the else cases are
always 0. The read val from rtw89_mac_read_lte() isn't used, so remove
this statement.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-11-pkshih@realtek.com
The BT-coexistence uses these function to control antenna and TDMA, so
implement the variant type to support all chips.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-10-pkshih@realtek.com
Fix array_size.cocci warning in tools/testing/selftests/net.
Use `ARRAY_SIZE(arr)` instead of forms like `sizeof(arr)/sizeof(arr[0])`.
It has been tested with gcc (Debian 8.3.0-6) 8.3.0.
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Link: https://lore.kernel.org/r/20220316092858.9398-1-guozhengkui@vivo.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Initialize FW status and disabled H2C function if CPU disabled. Then, it
can reset to initial state.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-9-pkshih@realtek.com
8852C add new hardware feature -- preload window, which is used to load
more data to D-MAC, so it can possibly yield better performance.
This patch is to configure preload and reserved size for next window.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-8-pkshih@realtek.com
Modify functions that control D-MAC (data MAC) and LDO to support variant
chips.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-7-pkshih@realtek.com
The format of RF parameter is changed; it doesn't encode delay parameters
into table, but the delay coding becomes regular pair of register address
and value.
To help firmware to recover RF register settings, we need to download
these parameters to firmware. For v1 format, only download partial
parameters (ignore them with addr < 0x100).
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-6-pkshih@realtek.com
Using encoded address which BIT(16) is used to discriminate which region is
going to access. Illustrate the calling flow as below
rtw89_phy_write_rf_v1() -+-> rtw89_phy_write_rf() // old interface
+-> rtw89_phy_write_rf_a() // new interface
Signed-off-by: Chung-Hsuan Hung <hsuan8331@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-5-pkshih@realtek.com
Configure this TX power to indicate TX power offset that uses to transmit
TB (trigger base) uplink frames.
Also, shrink the unit of TX power offset changes to suitable type s8.
Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-4-pkshih@realtek.com
The CFO tracking algorithm is the same, but control methods are different.
Set parameters via xtal serial interfaces (SI).
Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-3-pkshih@realtek.com
The dcfo_comp is digital CFO (central frequency offset) compensation.
Since the flow can be shared with all chips, add chip parameters to support
variant register address and format.
Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-2-pkshih@realtek.com
There are some spelling mistakes in some literal strings. Fix them.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220316234242.55515-1-colin.i.king@gmail.com
Building iwlmei without CONFIG_CFG80211 causes a link-time warning:
ld.lld: error: undefined symbol: ieee80211_hdrlen
>>> referenced by net.c
>>> net/wireless/intel/iwlwifi/mei/net.o:(iwl_mei_tx_copy_to_csme) in archive drivers/built-in.a
Add an explicit dependency to avoid this. In theory it should not
be needed here, but it also seems pointless to allow IWLMEI
for configurations without CFG80211.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Emmanuel Grumbach <Emmanuel.grumbach@intel.com>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220316183617.1470631-1-arnd@kernel.org
This code works but it has a static checker warning:
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1687 init_dma_rx_desc_rings()
warn: always true condition '(queue >= 0) => (0-u32max >= 0)'
Obviously, it makes no sense to check if an unsigned int is >= 0. What
prevents this code from being a forever loop is that later there is a
separate check for if (queue == 0).
The "queue" variable is less than MTL_MAX_RX_QUEUES (8) so it can easily
fit in an int type. Any larger value for "queue" would lead to an array
overflow when we assign "rx_q = &priv->rx_queue[queue]".
Fixes: de0b90e52a ("net: stmmac: rearrange RX and TX desc init into per-queue basis")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220316083744.GB30941@kili
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: 6d4e5c570c ("net: dsa: get port type at parse time")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220316082602.10785-1-linmq006@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch adds support for encapsulating IPv4/IPv6 within GENEVE.
In order to use this, a new IFLA_GENEVE_INNER_PROTO_INHERIT flag needs
to be provided at device creation. This property cannot be changed for
the time being.
In case IP traffic is received on a non-tun device the drop count is
increased.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Link: https://lore.kernel.org/r/20220316061557.431872-1-eyal.birger@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The 98DX2530 SoC is similar to the Armada 3700 except it needs a
different MBUS window configuration. Add a new compatible string to
identify this device and the required MBUS window configuration.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The out of band port on the 98DX2530 SoC is similar to the armada-3700
except it requires a slightly different MBUS window configuration. Add a
new compatible string so this difference can be accounted for.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Roi Dayan says:
====================
flow_offload: add tc vlan push_eth and pop_eth actions
Offloading vlan push_eth and pop_eth actions is needed in order to
correctly offload MPLSoUDP encap and decap flows, this series extends
the flow offload API to support these actions and updates mlx5 to
parse them.
====================
Link: https://lore.kernel.org/r/20220315110211.1581468-1-roid@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the MPLSoUDP encap offload does the L2 pop implicitly
while adding such action explicitly (vlan eth_push) will cause
the rule to not be offloaded.
Solve it by adding offload support for vlan eth_push in case of
MPLSoUDP decap case.
Flow example:
filter root protocol ip pref 1 flower chain 0
filter root protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
dst_ip 2.2.2.22
src_ip 2.2.2.21
in_hw in_hw_count 1
action order 1: vlan pop_eth pipe
index 1 ref 1 bind 1
used_hw_stats delayed
action order 2: mpls push protocol mpls_uc label 555 tc 3 ttl 255 pipe
index 1 ref 1 bind 1
used_hw_stats delayed
action order 3: tunnel_key set
src_ip 8.8.8.21
dst_ip 8.8.8.22
dst_port 6635
csum
tos 0x4
ttl 6 pipe
index 1 ref 1 bind 1
used_hw_stats delayed
action order 4: mirred (Egress Redirect to device bareudp0) stolen
index 1 ref 1 bind 1
used_hw_stats delayed
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently action pedit of source and destination MACs is used
to fill the MACs in L2 push step in MPLSoUDP decap offload,
this isn't aligned to tc SW which use vlan eth_push action
to do this.
To fix that, offload support for vlan veth_push action is
added together with mpls pop action, and deprecate the use
of pedit of MACs.
Flow example:
filter protocol mpls_uc pref 1 flower chain 0
filter protocol mpls_uc pref 1 flower chain 0 handle 0x1
eth_type 8847
mpls_label 555
enc_dst_port 6635
in_hw in_hw_count 1
action order 1: tunnel_key unset pipe
index 2 ref 1 bind 1
used_hw_stats delayed
action order 2: mpls pop protocol ip pipe
index 2 ref 1 bind 1
used_hw_stats delayed
action order 3: vlan push_eth dst_mac de:a2:ec:d6:69:c8 src_mac de:a2:ec:d6:69:c8 pipe
index 2 ref 1 bind 1
used_hw_stats delayed
action order 4: mirred (Egress Redirect to device enp8s0f0_0) stolen
index 2 ref 1 bind 1
used_hw_stats delayed
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add vlan push_eth and pop_eth action to the hardware intermediate
representation model which would subsequently allow it to be used
by drivers for offload.
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This kind of interface doesn't have a mac header. This patch fixes
bpf_redirect() to a PIM interface.
Fixes: 27b29f6305 ("bpf: add bpf_redirect() helper")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20220315092008.31423-1-nicolas.dichtel@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a port joins a bridge that it can't offload, it will fallback to
standalone mode and software bridging. In this case, we never want to
offload any FDB entries to hardware either.
Previously, for host addresses, we would eventually end up in
dsa_port_bridge_host_fdb_add, which would unconditionally dereference
dp->bridge and cause a segfault.
Fixes: c26933639b ("net: dsa: request drivers to perform FDB isolation")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220315233033.1468071-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix following includecheck warning:
./drivers/phy/freescale/phy-fsl-lynx-28g.c: linux/workqueue.h is
included more than once.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220315235603.59481-1-yang.lee@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cannot directly return platform_get_irq return irq, there
are operations that need to be undone.
Fixes: bf2b83425b ("net: mv643xx_eth: use platform_get_irq() instead of platform_get_resource()")
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220316012444.2126070-1-chi.minghao@zte.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In file hamradio/baycom_epp.c, the baycom_setmode interface, there
is a problem with improper use of strstr.
Suppose that when modestr="noloopback", both conditions which are
'strstr(modestr,"noloopback")' and 'strstr(modestr,"loopback")'
will be true(not NULL), this lead the bc->cfg.loopback variable
will be first assigned to 0, and then reassigned to 1.
This will cause 'bc->cfg.loopback = 0' will never take effect. That
obviously violates the logic of the code, so adjust the order of
their execution to solve the problem.
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220315074851.6456-1-tangmeng@uniontech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bareudp_create_sock() use AF_INET6 by default if IPv6 CONFIG enabled.
But if user start kernel with ipv6.disable=1, the bareudp sock will
created failed, which cause the interface open failed even with ethertype
ip. e.g.
# ip link add bareudp1 type bareudp dstport 2 ethertype ip
# ip link set bareudp1 up
RTNETLINK answers: Address family not supported by protocol
Fix it by using ipv6_mod_enabled() to check if IPv6 enabled. There is
no need to check IS_ENABLED(CONFIG_IPV6) as ipv6_mod_enabled() will
return false when CONFIG_IPV6 no enabled in include/linux/ipv6.h.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: 571912c69f ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20220315062618.156230-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEBsvAIBsPu6mG7thcrX5LkNig010FAmIyS4wTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCtfkuQ2KDTXXh+B/9f2BSFmv8Um1ajAl+On7JTGi9DhPj7
WOlFCX3NbcyQIrZ/0F4exi7WAani2NyCLke+UQAbIBiNPyUpkTv9gYCcPj8Tq5S6
oJyWf8qRt2T8Gth/MJVm60N8TDUjjNfdSrYHLL4HSUF6zd9hpAQXv/4AXTXrZC6K
4bPGTeNOEvsWwKg+wmdtIO5YnZwilc1sA85TLNq6En0asBUAT3h08P56rex2Stg0
qu9HjAvQ+szpGrgwB2Uk6x8h2BKF+BXhz9/Cn7eCFjOP+YTDjVbqbap0wDXZy4Mt
Eg2g9gRmfvB0MjseWf+PoxoAsO7X9T0JNBqbULBipR+PvWOne6oD53yK
=KN3V
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.18-20220316' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-03-16
the first 3 patches are by Oliver Hartkopp target the CAN ISOTP
protocol and fix a problem found by syzbot in isotp_bind(), return
-EADDRNOTAVAIL in unbound sockets in isotp_recvmsg() and add support
for MSG_TRUNC to isotp_recvmsg().
Amit Kumar Mahapatra converts the xilinx,can device tree bindings to
yaml.
The last patch is by Julia Lawall and fixes typos in the ucan driver.
* tag 'linux-can-next-for-5.18-20220316' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: ucan: fix typos in comments
dt-bindings: can: xilinx_can: Convert Xilinx CAN binding to YAML
can: isotp: support MSG_TRUNC flag when reading from socket
can: isotp: return -EADDRNOTAVAIL when reading from unbound socket
can: isotp: sanitize CAN ID checks in isotp_bind()
====================
Link: https://lore.kernel.org/r/20220316204710.716341-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Various spelling mistakes in comments.
Detected with the help of Coccinelle.
Link: https://lore.kernel.org/all/20220314115354.144023-28-Julia.Lawall@inria.fr
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Convert Xilinx CAN binding documentation to YAML.
Link: https://lore.kernel.org/all/20220316171105.17654-1-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Qian Cai
Guo Ziliang
Ivan Vecera
Vladimir Oltean
Doug Berger
Manish Chopra
Juerg Haefliger
Tom Rix
Kalle Valo
Ping-Ke Shih
Chia-Yuan Li
Guo Zhengkui
Chung-Hsuan Hung
Yuan-Han Zhang
Colin Ian King
Arnd Bergmann
Dan Carpenter
Miaoqian Lin
Eyal Birger
Paolo Abeni
Chris Packham
Jonathan Lemon
Jakub Kicinski
Maor Dickman
Nicolas Dichtel
Tobias Waldekranz
Yang Li
Minghao Chi
wujunwen
Meng Tang
Hangbin Liu
Julia Lawall
Amit Kumar Mahapatra
Oliver Hartkopp