There were a few files in the regmap code that did not have SPDX
identifiers on them, so fix that up. At the same time, remove the "free
form" text that specified the license of the file, as that is impossible
for any tool to properly parse.
Also, as Mark loves // comment markers, convert all of the headers to be
the same to make things look consistent :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap API had a noinc_read function added for instances where devices
supported returning data from an internal FIFO in a single read.
This commit adds the noinc_write variant to allow writing to a non
incrementing register, this is used in devices such as the sx1301 for
loading firmware.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap API usually assumes that bulk read operations will read a
range of registers but some I2C/SPI devices have certain registers for
which a such a read operation will return data from an internal FIFO
instead. Add an explicit API to support bulk read without range semantics.
Some linux drivers use regmap_bulk_read or regmap_raw_read for such
registers, for example mpu6050 or bmi150 from IIO. This only happens to
work because when caching is disabled a single regmap read op will map
to a single bus read op (as desired). This breaks if caching is enabled and
reg+1 happens to be a cacheable register.
Without regmap support refactoring a driver to enable regmap caching
requires separate I2C and SPI paths. This is exactly what regmap is
supposed to help avoid.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The recently added support for disabling the regmap internal locking left
debugfs enabled for devices with the locking disabled. This is a problem
since debugfs allows userspace to do things like initiate reads from the
hardware which will use the scratch buffers protected by the regmap locking
so could cause data corruption.
For safety address this by just disabling debugfs for these devices. That
is overly conservative since some of the debugfs files just read internal
data structures but it's much simpler to implmement and less likely to
lead to problems with tooling that works with debugfs.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On some platforms, when reading or writing some special registers through
regmap, we should acquire one hardware spinlock to synchronize between
the multiple subsystems. Thus this patch adds the hardware spinlock
support for regmap.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently only support masking the top bit for read and write
flags. Let's make the mask unsigned long and mask the bytes based
on the configured register length to make things more generic.
This allows using regmap for more exotic combinations like SPI
devices that need little endian addressing.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a function to check if a regmap register is cached. This will be used
in debugfs to dump the cached values of write only registers.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
internal.h is using dev_name() but doesn't include device.h which
defines it. Add an explicit include to avoid build problems due to
this.
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here introduces regcache_get_index_by_order() for regmap cache,
which uses the register stride order and bit rotation, to improve
the performance.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the register stride should always equal to 2^N, and bit rotation is
much faster than multiplication and division. So introducing the stride
order and using bit rotation to get the offset of the register from the
index to improve the performance.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch of
debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6ePQACgkQMUfUDdst+ymNTgCgpP0CZw57GpwF/Hp2L/lMkVeo
Kx8AoKhEi4iqD5fdCQS9qTfomB+2/M6g
=g7ZO
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch
of debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time"
* tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Add debugfs_create_ulong()
of: to support binding numa node to specified device in devicetree
debugfs: Add read-only/write-only bool file ops
debugfs: Add read-only/write-only size_t file ops
debugfs: Add read-only/write-only x64 file ops
debugfs: Consolidate file mode checks in debugfs_create_*()
Revert "mm: Check if section present during memory block (un)registering"
driver-core: platform: Provide helpers for multi-driver modules
mm: Check if section present during memory block (un)registering
devres: fix a for loop bounds check
CMA: fix CONFIG_CMA_SIZE_MBYTES overflow in 64bit
base/platform: assert that dev_pm_domain callbacks are called unconditionally
sysfs: correctly handle short reads on PREALLOC attrs.
base: soc: siplify ida usage
kobject: move EXPORT_SYMBOL() macros next to corresponding definitions
kobject: explain what kobject's sd field is
debugfs: document that debugfs_remove*() accepts NULL and error values
debugfs: Pass bool pointer to debugfs_create_bool()
ACPI / EC: Fix broken 64bit big-endian users of 'global_lock'
This commit allows installing a custom reg_update_bits function for cases where
the hardware provides a mechanism to set or clear register bits without a
read/modify/write cycle. Such is the case with the Microchip ENCX24J600.
If a custom reg_update_bits function is provided, it will only be used against
volatile registers.
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Its a bit odd that debugfs_create_bool() takes 'u32 *' as an argument,
when all it needs is a boolean pointer.
It would be better to update this API to make it accept 'bool *'
instead, as that will make it more consistent and often more convenient.
Over that bool takes just a byte.
That required updates to all user sites as well, in the same commit
updating the API. regmap core was also using
debugfs_{read|write}_file_bool(), directly and variable types were
updated for that to be bool as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a regmap is using fast_io, allocate the scratch buffer in
regmap_bulk_write() with GFP_ATOMIC instead of GFP_KERNEL.
Otherwise we may schedule while atomic.
Reported-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are some buses which have a limit on the maximum number of bytes
that can be send/received. An example for this is
I2C_FUNC_SMBUS_I2C_BLOCK which does not support any reads/writes of more
than 32 bytes. The regmap_bulk operations should still be able to
utilize the full 32 bytes in this case.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
use_single_rw currently reflects the capabilities of the connected
device. The capabilities of the bus are currently missing for this
variable.
As there are read only and write only buses we need seperate values for
use_single_rw to also reflect tha capabilities of the bus.
This patch splits use_single_rw into use_single_read and
use_single_write. The initialization is changed to check the
configuration for use_single_rw and to check the capabilities of the
used bus.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Separate the functionality using sequences of register writes from the
functions that take register defaults. This change renames the arguments
in order to support the extension of reg_sequence to take an optional
delay to be applied after any given register in a sequence is written.
This avoids adding an int to all register defaults, which could
substantially increase memory usage for regmaps with large default tables.
This also updates all the clients of multi_reg_write/register_patch.
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Existing regmap users call regcache_mark_dirty() as part of the
suspend/resume sequence, to tell regcache that non-default values need to
be resynced post-resume. Add an internal "no_sync_defaults" regmap flag
to remember this state, so that regcache_sync() can differentiate between
these two cases:
1) HW was reset, so any cache values that match map->reg_defaults can be
safely skipped. On some chips there are a lot of registers in the
reg_defaults list, so this optimization speeds things up quite a bit.
2) HW was not reset (maybe it was just clock-gated), so if we cached
any writes, they should be sent to the hardware regardless of whether
they match the HW default. Currently this will write out all values in
the regcache, since we don't maintain per-register dirty bits.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We'll need to call it from regmap-i2c.c, which can be built as module.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch move struct regmap.spinlock_flags into the union of
spinlock, so that we can shrink struct regmap size.
Signed-off-by: Yalin Wang <yalin.wang@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch change struct regmap->mutex and struct regmap->spinlock
as an union, because these 2 members are only used one of them,
we change it to shrink the struct size.
Signed-off-by: Yalin Wang <yalin.wang@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 6cfec04bcc ("regmap: Separate regmap dev initialization") moved the
regmap debugfs initialization after regcache initialization. This means
that the regmap debugfs directory is not created yet when the cache
initialization runs and so any debugfs files registered by the regcache are
created in the debugfs root directory rather than the debugfs directory of
the regmap instance. Fix this by adding a separate callback for the
regcache debugfs initialization which will be called after the parent
debugfs entry has been created.
Fixes: 6cfec04bcc (regmap: Separate regmap dev initialization)
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This is the implementation of regmap_multi_reg_write()
There is a new capability 'can_multi_write' that device drivers
must set in order to use this multi reg write mode.
This replaces the first definition, which just defined the API.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Rather than passing a flag around through the entire call stack store it
in the regmap struct and read it when required. This minimises the
visibility of the feature through the API, minimising the code updates
needed to use it more widely.
Signed-off-by: Mark Brown <broonie@linaro.org>
Rather than allocating and deallocating the structures used to manage async
transfers each time we do one keep the structures around as long as the
regmap is around. This should provide a small performance improvement.
Signed-off-by: Mark Brown <broonie@linaro.org>
Current Linux kernel is supporting regmap_field method
and it is very useful feature.
It needs one regmap_filed for one register access.
OTOH, there is multi port device which
has many same registers in the market.
The difference for each register access is
only its address offset.
Current API needs many regmap_field for such device,
but it is not good.
This patch adds new regmap_fileds API which can care
about multi port/offset access via regmap.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With devices which have a dense and small register map but placed at a large
offset the global cache_present bitmap imposes a huge memory overhead. Making
the cache_present per rbtree node avoids the issue and easily reduces the memory
footprint by a factor of ten. For devices with a more sparse map or without a
large base register offset the memory usage might increase slightly by a few
bytes, but not significantly. E.g. for a device which has ~50 registers at
offset 0x4000 the memory footprint of the register cache goes down form 2496
bytes to 175 bytes.
Moving the bitmap to a per node basis means that the handling of the bitmap is
now cache implementation specific and can no longer be managed by the core. The
regcache_sync_block() function is extended by a additional parameter so that the
cache implementation can tell the core which registers in the block are set and
which are not. The parameter is optional and if NULL the core assumes that all
registers are set. The rbtree cache also needs to implement its own drop
callback instead of relying on the core to handle this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the initial case when no reg_defaults values are
provided and no register value was added to the cache
yet, the cache_present bitmap is NULL. If this function
is invoked for any register it should return false
(i.e. the register is not cached) instead of true.
Signed-off-by: Ionut Nicu <ioan.nicu.ext@nsn.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It is common to access regmap registers at bit level, using
regmap_update_bits or regmap_read functions, however the end user has to
take care of a mask or shifting. This becomes overhead when such use
cases are high. Having a common function to do this is much convenient
and less error prone.
The idea of regmap_field is simple, regmap_field gives a logical
structure to bits of the regmap register, and the driver can use this
logical entity without the knowledge of the bit positions and masks all
over the code. This way code looks much neat and it need not handle the
masks, shifts every time it access the those entities.
With this new regmap_field_read/write apis the end user can setup a
regmap field using regmap_field_init and use the return regmap_field to
read write the register field without worrying about the masks or
shifts.
Also this apis will be useful for drivers which are based on regmaps,
like some clocks or pinctrls which can work on the regmap_fields
directly without having to worry about bit positions.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
regmap-mmio uses a spinlock with spin_lock() and spin_unlock() for locking.
To be able to use the regmap API from different contexts (atomic vs non-atomic),
without the risk of race conditions, we need to use spin_lock_irqsave() and
spin_lock_irqrestore() instead. A new field, the spinlock_flags field, is added
to regmap struct to store the flags between regmap_{,un}lock_spinlock(). The
spinlock_flags field itself is also protected by the spinlock.
Thanks to Stephen Warren for the suggestion of this particular solution.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow drivers to discard parts of the register cache, for example if part
of the hardware has been reset.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The idea of holding blocks of registers in device format is shared between
at least rbtree and lzo cache formats so split out the loop that does the
sync from the rbtree code so optimisations on it can be reused.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
The idea of maintaining a bitmap of present registers is something that
can usefully be used by other cache types that maintain blocks of cached
registers so move the code out of the rbtree cache and into the generic
regcache code.
Refactor the interface slightly as we go to wrap the set bit and enlarge
bitmap operations (since we never do one without the other) and make it
more robust for reads of uncached registers by bounds checking before we
look at the bitmap.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Provide a helper to do the size based index into a block of registers and
use it when reading a value.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows the cache to sync values directly to the device when stored
in native format and also allows asynchronous I/O.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This file lists the register ranges in the register map. The condition
to split the range is based on whether the block is readable or not.
Ensure that we lock the `debugfs_off_cache' list whenever we access
and modify the list. There is a possible race otherwise between the
read() operations of the `registers' file and the `range' file.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the value parsing operations both return the parsed value and
modify the passed buffer. This precludes their use in places like the cache
code so split out the in place modification into a new parse_inplace()
operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's more idiomatic to pass the map structure around and this means we
can use other bits of information from the map.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Greg Kroah-Hartman
Mark Brown
Ben Whitten
David Frey
Crestez Dan Leonard
Baolin Wang
Tony Lindgren
Cristian Birsan
Xiubo Li
Linus Torvalds
Jon Ringle
Viresh Kumar
Stephen Boyd
Markus Pargmann
Nariman Poushin
Kevin Cernekee
Philipp Zabel
Guenter Roeck
Wang, Yalin
Lars-Peter Clausen
Opensource [Anthony Olech]
Mark Brown
Kuninori Morimoto
Ionut Nicu
Srinivas Kandagatla
Mark Brown
Dimitris Papastamos