Граф коммитов

52 Коммитов

Автор SHA1 Сообщение Дата
Tejun Heo 705e76beb9 libata: restructure SFF post-reset readiness waits
Previously, post-softreset readiness is waited as follows.

1. ata_sff_wait_after_reset() waits for 150ms and then for
   ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.

2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff.
   If not, continue to #3.

3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending
   on devmask using ata_sff_wait_ready().

And for post-hardreset readiness,

1. ata_sff_wait_after_reset() waits for 150ms and then for
   ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.

2. sata_sff_hardreset waits for device readiness using
   ata_sff_wait_ready().

This patch merges and unifies post-reset readiness waits into
ata_sff_wait_ready() and ata_sff_wait_after_reset().

ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready().  If TF
status is 0xff, link status is unknown and the port is SATA, it will
continue polling till ATA_TMOUT_FF_WAIT.

ata_sff_wait_after_reset() is updated to perform the following steps.

1. waits for 150ms.

2. waits for dev0 readiness using ata_sff_wait_ready().  Note that
   this is done regardless of devmask, as ata_sff_wait_ready() handles
   0xff status correctly, this preserves the original behavior except
   that it may wait longer after softreset if link is online but
   status is 0xff.  This behavior change is very unlikely to cause any
   actual difference and is intended.  It brings softreset behavior to
   that of hardreset.

3. waits for dev1 readiness just the same way ata_bus_post_reset() did.

Now both soft and hard resets call ata_sff_wait_after_reset() after
reset to wait for readiness after resets.  As
ata_sff_wait_after_reset() contains calls to ->sff_dev_select(),
explicit call near the end of sata_sff_hardreset() is removed.

This change makes reset implementation simpler and more consistent.

While at it, make the magical 150ms wait post-reset wait duration a
constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take
@link instead of @ap.  This is to make them consistent with other
reset helpers and ease core changes.

pata_scc is updated accordingly.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo 5682ed33aa libata: rename SFF port ops
Add sff_ prefix to SFF specific port ops.

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames ops and doesn't introduce any
behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo 9363c3825e libata: rename SFF functions
SFF functions have confusing names.  Some have sff prefix, some have
bmdma, some std, some pci and some none.  Unify the naming by...

* SFF functions which are common to both BMDMA and non-BMDMA are
  prefixed with ata_sff_.

* SFF functions which are specific to BMDMA are prefixed with
  ata_bmdma_.

* SFF functions which are specific to PCI but apply to both BMDMA and
  non-BMDMA are prefixed with ata_pci_sff_.

* SFF functions which are specific to PCI and BMDMA are prefixed with
  ata_pci_bmdma_.

* Drop generic prefixes from LLD specific routines.  For example,
  bfin_std_dev_select -> bfin_dev_select.

The following renames are noteworthy.

  ata_qc_issue_prot() -> ata_sff_qc_issue()
  ata_pci_default_filter() -> ata_bmdma_mode_filter()
  ata_dev_try_classify() -> ata_sff_dev_classify()

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames functions and doesn't
introduce any behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:21 -04:00
Tejun Heo 6fd3639011 libata: kill ata_chk_status()
ata_chk_status() just calls ops->check_status and it only adds
confusion with other status functions.  Kill it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo a1efdaba2d libata: make reset related methods proper port operations
Currently reset methods are not specified directly in the
ata_port_operations table.  If a LLD wants to use custom reset
methods, it should construct and use a error_handler which uses those
reset methods.  It's done this way for two reasons.

First, the ops table already contained too many methods and adding
four more of them would noticeably increase the amount of necessary
boilerplate code all over low level drivers.

Second, as ->error_handler uses those reset methods, it can get
confusing.  ie. By overriding ->error_handler, those reset ops can be
made useless making layering a bit hazy.

Now that ops table uses inheritance, the first problem doesn't exist
anymore.  The second isn't completely solved but is relieved by
providing default values - most drivers can just override what it has
implemented and don't have to concern itself about higher level
callbacks.  In fact, there currently is no driver which actually
modifies error handling behavior.  Drivers which override
->error_handler just wraps the standard error handler only to prepare
the controller for EH.  I don't think making ops layering strict has
any noticeable benefit.

This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and
their PMP counterparts propoer ops.  Default ops are provided in the
base ops tables and drivers are converted to override individual reset
methods instead of creating custom error_handler.

* ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs
  aren't accessible.  sata_promise doesn't need to use separate
  error_handlers for PATA and SATA anymore.

* softreset is broken for sata_inic162x and sata_sx4.  As libata now
  always prefers hardreset, this doesn't really matter but the ops are
  forced to NULL using ATA_OP_NULL for documentation purpose.

* pata_hpt374 needs to use different prereset for the first and second
  PCI functions.  This used to be done by branching from
  hpt374_error_handler().  The proper way to do this is to use
  separate ops and port_info tables for each function.  Converted.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:18 -04:00
Tejun Heo 029cfd6b74 libata: implement and use ops inheritance
libata lets low level drivers build ata_port_operations table and
register it with libata core layer.  This allows low level drivers
high level of flexibility but also burdens them with lots of
boilerplate entries.

This becomes worse for drivers which support related similar
controllers which differ slightly.  They share most of the operations
except for a few.  However, the driver still needs to list all
operations for each variant.  This results in large number of
duplicate entries, which is not only inefficient but also error-prone
as it becomes very difficult to tell what the actual differences are.

This duplicate boilerplates all over the low level drivers also make
updating the core layer exteremely difficult and error-prone.  When
compounded with multi-branched development model, it ends up
accumulating inconsistencies over time.  Some of those inconsistencies
cause immediate problems and fixed.  Others just remain there dormant
making maintenance increasingly difficult.

To rectify the problem, this patch implements ata_port_operations
inheritance.  To allow LLDs to easily re-use their own ops tables
overriding only specific methods, this patch implements poor man's
class inheritance.  An ops table has ->inherits field which can be set
to any ops table as long as it doesn't create a loop.  When the host
is started, the inheritance chain is followed and any operation which
isn't specified is taken from the nearest ancestor which has it
specified.  This operation is called finalization and done only once
per an ops table and the LLD doesn't have to do anything special about
it other than making the ops table non-const such that libata can
update it.

libata provides four base ops tables lower drivers can inherit from -
base, sata, pmp, sff and bmdma.  To avoid overriding these ops
accidentaly, these ops are declared const and LLDs should always
inherit these instead of using them directly.

After finalization, all the ops table are identical before and after
the patch except for setting .irq_handler to ata_interrupt in drivers
which didn't use to.  The .irq_handler doesn't have any actual effect
and the field will soon be removed by later patch.

* sata_sx4 is still using old style EH and currently doesn't take
  advantage of ops inheritance.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo 68d1d07b51 libata: implement and use SHT initializers
libata lets low level drivers build scsi_host_template and register it
to the SCSI layer.  This allows low level drivers high level of
flexibility but also burdens them with lots of boilerplate entries.

This patch implements SHT initializers which can be used to initialize
all the boilerplate entries in a sht.  Three variants of them are
implemented - BASE, BMDMA and NCQ - for different types of drivers.
Note that entries can be overriden by putting individual initializers
after the helper macro.

All sht tables are identical before and after this patch.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo 6bd99b4e09 libata: normalize port_info, port_operations and sht tables
Over the time, port info, ops and sht structures developed quite a bit
of inconsistencies.  This patch updates drivers.

* Enable/disable_pm callbacks added to all ahci ops tables.

* Every driver for SFF controllers now uses ata_sff_port_start()
  instead of ata_port_start() unless the driver has custom
  implementation.

* Every driver for SFF controllers now uses ata_pci_default_filter()
  unless the driver has custom implementation.

* Removed an odd port_info->sht initialization from ata_piix.c.
  Likely a merge byproduct.

* A port which has ATA_FLAG_SATA set doesn't need to set cable_detect
  to ata_cable_sata().  Remove it from via and mv port ops.

* Some drivers had unnecessary .max_sectors initialization which is
  ignored and was missing .slave_destroy callback.  Fixed.

* Removed unnecessary sht initializations port_info's.

* Removed onsolete scsi device suspend/resume callbacks from
  pata_bf54x.

* No reason to set ata_pci_default_filter() and bmdma functions for
  PIO-only drivers.  Remove those callbacks and replace
  ata_bmdma_irq_clear with ata_noop_irq_clear.

* pata_platform sets port_start to ata_dummy_ret0.  port_start can
  just be set to NULL.

* sata_fsl supports NCQ but was missing qc_defer.  Fixed.

* pata_rb600_cf implements dummy port_start.  Removed.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo cf48062658 libata: prefer hardreset
When both soft and hard resets are available, libata preferred
softreset till now.  The logic behind it was to be softer to devices;
however, this doesn't really help much.  Rationales for the change:

* BIOS may freeze lock certain things during boot and softreset can't
  unlock those.  This by itself is okay but during operation PHY event
  or other error conditions can trigger hardreset and the device may
  end up with different configuration.

  For example, after a hardreset, previously unlockable HPA can be
  unlocked resulting in different device size and thus revalidation
  failure.  Similar condition can occur during or after resume.

* Certain ATAPI devices require hardreset to recover after certain
  error conditions.  On PATA, this is done by issuing the DEVICE RESET
  command.  On SATA, COMRESET has equivalent effect.  The problem is
  that DEVICE RESET needs its own execution protocol.

  For SFF controllers with bare TF access, it can be easily
  implemented but more advanced controllers (e.g. ahci and sata_sil24)
  require specialized implementations.  Simply using hardreset solves
  the problem nicely.

* COMRESET initialization sequence is the norm in SATA land and many
  SATA devices don't work properly if only SRST is used.  For example,
  some PMPs behave this way and libata works around by always issuing
  hardreset if the host supports PMP.

  Like the above example, libata has developed a number of mechanisms
  aiming to promote softreset to hardreset if softreset is not going
  to work.  This approach is time consuming and error prone.

  Also, note that, dependingon how you read the specs, it could be
  argued that PMP fan-out ports require COMRESET to start operation.
  In fact, all the PMPs on the market except one don't work properly
  if COMRESET is not issued to fan-out ports after PMP reset.

* COMRESET is an integral part of SATA connection and any working
  device should be able to handle COMRESET properly.  After all, it's
  the way to signal hardreset during reboot.  This is the most used
  and recommended (at least by the ahci spec) method of resetting
  devices.

So, this patch makes libata prefer hardreset over softreset by making
the following changes.

* Rename ATA_EH_RESET_MASK to ATA_EH_RESET and use it whereever
  ATA_EH_{SOFT|HARD}RESET used to be used.  ATA_EH_{SOFT|HARD}RESET is
  now only used to tell prereset whether soft or hard reset will be
  issued.

* Strip out now unneeded promote-to-hardreset logics from
  ata_eh_reset(), ata_std_prereset(), sata_pmp_std_prereset() and
  other places.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:15 -04:00
Harvey Harrison 48e1f800ea ata: fix sparse warning in sata_via.c
drivers/ata/sata_via.c:336:2: warning: returning void-valued expression

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:51:01 -05:00
Alejandro Riveira Fernández 4f743d1d22 sata_via.c: Remove missleading comment.
Maybe for the trivial tree...

sata_via.c has PATA support since:

  d73f30e1c9

  sata_via: PATA support

AFAICS so the TODO list is no longer true.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-06 07:00:33 -05:00
Jeff Garzik 5796d1c4c8 [libata] Address some checkpatch-spotted issues
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-29 06:15:27 -04:00
Al Viro b4482a4b2e more trivial signedness fixes in drivers
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-14 12:41:52 -07:00
Tejun Heo b6d6c74628 sata_via: kill SATA_PATA_SHARING register handling
The SATA_PATA_SHARING register doesn't have anything to do with the
SATA part of the controller.  It indicates whether an extern SATA PHY
is attached to the PATA part of the controller and if so how it is
wired.  As the PATA part is driven by pata_via, sata_via has no reason
to care about that.  Also, pata_via should work fine under all
configurations.

This patch removes unnecessary attach failures.  It seems recent via
chipsets are defaulting to different values or are actually connected
to SATA PHY triggering this more often.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:42 -04:00
Tejun Heo cbcdd87593 libata: implement and use ata_port_desc() to report port configuration
Currently, port configuration reporting has the following problems.

* iomapped address is reported instead of raw address
* report contains irrelevant fields or lacks necessary fields for
  non-SFF controllers.
* host->irq/irq2 are there just for reporting and hacky.

This patch implements and uses ata_port_desc() and
ata_port_pbar_desc().  ata_port_desc() is almost identical to
ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no
locking requirement, can only be used during host initialization and "
" is used as separator instead of ", ".  ata_port_pbar_desc() is a
helper to ease reporting of a PCI BAR or an offsetted address into it.

LLD pushes whatever description it wants using the above two
functions.  The accumulated description is printed on host
registration after "[S/P]ATA max MAX_XFERMODE ".

SFF init helpers and ata_host_activate() automatically add
descriptions for addresses and irq respectively, so only LLDs which
isn't standard SFF need to add custom descriptions.  In many cases,
such controllers need to report different things anyway.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:37 -04:00
Jeff Garzik ac8869d56d [libata] Remove ->port_disable() hook
It was always set to ata_port_disable().  Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:35 -04:00
Jeff Garzik 6d32d30f55 [libata] Remove ->irq_ack() hook, and ata_dummy_irq_on()
* ->irq_ack() is redundant to what the irq handler already
  performs... chk-status + irq-clear.  Furthermore, it is only
  called in one place, when screaming-irq-debugging is enabled,
  so we don't want to bother with a hook just for that.

* ata_dummy_irq_on() is only ever used in drivers that have
  no callpath reaching ->irq_on().  Remove .irq_on hook from
  those drivers, and the now-unused ata_dummy_irq_on()

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:34 -04:00
Tejun Heo cc0680a580 libata-link: linkify reset
Make reset methods and related functions deal with ata_link instead of
ata_port.

* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions

This patch introduces no behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:31 -04:00
Tejun Heo 9af5c9c97d libata-link: introduce ata_link
Introduce ata_link.  It abstracts PHY and sits between ata_port and
ata_device.  This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port.  Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.

This patch only defines the host link.  Multiple link handling will be
added later.  Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.

This patch introduces no behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:30 -04:00
Ondrej Zary b4154d4a01 Fix sata_via write errors on PATA drive connected to VT6421
I think that I've found and fixed the problem. There is a copy/paste bug in
vt6421_set_dma_mode() function which causes wrong values to be written to
PATA_UDMA_TIMING register.

This patch fixes a copy/paste bug that breaks DMA modes on VT6421 PATA port.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-09-01 06:52:18 -04:00
Jeff Garzik 2a3103ce43 [libata] Bump driver versions
Bump the versions for drivers that were modified, but had not already
had a version number bump.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-31 04:54:06 -04:00
Tejun Heo da3dbb17a0 libata: make ->scr_read/write callbacks return error code
Convert ->scr_read/write callbacks to return error code to better
indicate failure.  This will help handling of SCR_NOTIFICATION.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20 08:02:11 -04:00
Tejun Heo d583bc1881 libata: simplify PCI legacy SFF host handling
With PCI resource fix up for legacy hosts.  We can use the same code
path to allocate IO resources and initialize host for both legacy and
native SFF hosts.  Only IRQ requesting needs to be different.

Rename ata_pci_*_native_host() to ata_pci_*_sff_host(), kill all
legacy specific functions and use the renamed functions instead.  This
simplifies code a lot.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-10 21:27:09 -04:00
Jeff Garzik bf6263a853 [libata] Use ATA_UDMAx standard masks when filling driver's udma_mask info
The ATA_UDMAx masks are self-documenting, and far better than manually
writing in the hex mask.

Note that pata_it8213 mask differed from the comment.  Added a FIXME there.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-09 12:17:35 -04:00
Jeff Garzik a09060ffe5 [libata] sata_sx4, sata_via: minor documentation updates
sata_sx4:
- describe overall driver theory of operation
- add a few constants that will be used in the future

sata_via:
- remove mention of an old-EH function that is going away

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-09 12:17:33 -04:00
Jeff Garzik 52df0ee07c [libata] sata_via, pata_via: Add PCI IDs.
Supplied by VIA.

Also, convert named constants to hex values in the pata_via
PCI ID table.  (standard libata policy for PCI device IDs, which are
considered simply arbitrary hex numbers, without a need to create a
single-use constant in linux/pci_ids.h)

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-25 05:02:06 -04:00
Jeff Garzik 8bc3fc470e libata: bump versions
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-21 20:26:38 -04:00
Tejun Heo 8fd7d1b16e sata_via: pcim_iomap_regions() conversion missed BAR5
pcim_iomap_regions() conversion missed BAR5.  Fix it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-17 20:57:38 -04:00
Andrew Morton 1d30c33d8d git-libata-all: sata_via build fix
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-11 18:16:00 -04:00
Tejun Heo 1626aeb881 libata: clean up SFF init mess
The intention of using port_mask in SFF init helpers was to eventually
support exoctic configurations such as combination of legacy and
native port on the same controller.  This never became actually
necessary and the related code always has been subtly broken one way
or the other.  Now that new init model is in place, there is no reason
to make common helpers capable of handling all corner cases.  Exotic
cases can simply dealt within LLDs as necessary.

This patch removes port_mask handling in SFF init helpers.  SFF init
helpers don't take n_ports argument and interpret it into port_mask
anymore.  All information is carried via port_info.  n_ports argument
is dropped and always two ports are allocated.  LLD can tell SFF to
skip certain port by marking it dummy.  Note that SFF code has been
treating unuvailable ports this way for a long time until recent
breakage fix from Linus and is consistent with how other drivers
handle with unavailable ports.

This fixes 1-port legacy host handling still broken after the recent
native mode fix and simplifies SFF init logic.  The following changes
are made...

* ata_pci_init_native_host() and ata_init_legacy_host() both now try
  to initialized whatever they can and mark failed ports dummy.  They
  return 0 if any port is successfully initialized.

* ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't
  take n_ports argument.  All info should be specified via port_info
  array.  Always two ports are allocated.

* ata_pci_init_bmdma() exported to be used by LLDs in exotic cases.

* port_info handling in all LLDs are standardized - all port_info
  arrays are const stack variable named ppi.  Unless the second port
  is different from the first, its port_info is specified as NULL
  (tells libata that it's identical to the last non-NULL port_info).

* pata_hpt37x/hpt3x2n: don't modify static variable directly.  Make an
  on-stack copy instead as ata_piix does.

* pata_uli: It has 4 ports instead of 2.  Don't use
  ata_pci_prepare_native_host().  Allocate the host explicitly and use
  init helpers.  It's simple enough.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-11 18:09:18 -04:00
Tejun Heo e1e143cf97 sata_via: add missing PM hooks
For some reason, sata_via is missing PM hooks.  Add them.  Spotted by
Jeroen Janssen <jeroen.janssen@gmail.com>.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jeroen Janssen <jeroen.janssen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-09 20:15:46 -04:00
Tejun Heo d4b2bab4f2 libata: add deadline support to prereset and reset methods
Add @deadline to prereset and reset methods and make them honor it.
ata_wait_ready() which directly takes @deadline is implemented to be
used as the wait function.  This patch is in preparation for EH timing
improvements.

* ata_wait_ready() never does busy sleep.  It's only used from EH and
  no wait in EH is that urgent.  This function also prints 'be
  patient' message automatically after 5 secs of waiting if more than
  3 secs is remaining till deadline.

* ata_bus_post_reset() now fails with error code if any of its wait
  fails.  This is important because earlier reset tries will have
  shorter timeout than the spec requires.  If a device fails to
  respond before the short timeout, reset should be retried with
  longer timeout rather than silently ignoring the device.

  There are three behavior differences.

  1. Timeout is applied to both devices at once, not separately.  This
     is more consistent with what the spec says.

  2. When a device passes devchk but fails to become ready before
     deadline.  Previouly, post_reset would just succeed and let
     device classification remove the device.  New code fails the
     reset thus causing reset retry.  After a few times, EH will give
     up disabling the port.

  3. When slave device passes devchk but fails to become accessible
     (TF-wise) after reset.  Original code disables dev1 after 30s
     timeout and continues as if the device doesn't exist, while the
     patched code fails reset.  When this happens, new code fails
     reset on whole port rather than proceeding with only the primary
     device.

  If the failing device is suffering transient problems, new code
  retries reset which is a better behavior.  If the failing device is
  actually broken, the net effect is identical to it, but not to the
  other device sharing the channel.  In the previous code, reset would
  have succeeded after 30s thus detecting the working one.  In the new
  code, reset fails and whole port gets disabled.  IMO, it's a
  pathological case anyway (broken device sharing bus with working
  one) and doesn't really matter.

* ata_bus_softreset() is changed to return error code from
  ata_bus_post_reset().  It used to return 0 unconditionally.

* Spin up waiting is to be removed and not converted to honor
  deadline.

* To be on the safe side, deadline is set to 40s for the time being.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-01 07:49:53 -04:00
Tejun Heo eca25dca17 libata: convert drivers with combined SATA/PATA ports to new init model
Convert sata_via and sata_promise to new init model.  Both controllers
can have combined configuration (SATA + PATA) and used twisted
initialization method (modifying port in ->port_start) to overcome
probe_ent limitations.

This patch converts both drivers to new init model in which such
configuration is natively supported.

* promise: Combined pata port now uses separate port_info entry right
  after the sata counterpart entry.

* promise: Controller configuration is discerned using ap->flags.
  This simplifies init path and makes it look more like other LLDs.

* via: Both SATA and PATA ports in vt6421 are represented in their
  own port_info structure.

Tested on PDC20375 (SATA150 TX2plus) [105a:3375] and PDC40775 (SATA
300 TX2plus) [105a:3d73].  Couldn't test via cuz my c3 won't boot the
current kernel.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:16:03 -04:00
Jeff Garzik a0fcdc0259 [libata] Update several PATA drivers for new ->cable_detect hook
All patches authored and signed-off-by Alan Cox, sent on Mar 7, 2007.
I merely combined them all into a single patch.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:15:56 -04:00
Jeff Garzik cb48cab7f3 [libata] bump versions
Bump versions based on changes submitted during 2.6.21 merge window.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-26 06:04:24 -05:00
Jeff Garzik a84471fe26 [libata] Trim trailing whitespace.
No code changes.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-26 05:51:33 -05:00
Tejun Heo e1be5d73e0 sata_via: fix resource-managed iomap conversion
Conversion to resource-managed iomap was buggy causing init failures
on both vt6420 and 6421 - BAR5 wasn't mapped for both controllers
while on vt6420 sata_via tried to map BAR0-4 twice.  Fix it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-21 04:58:19 -05:00
Akira Iguchi 246ce3b675 libata: add another IRQ calls (libata drivers)
This patch is against each libata driver.

Two IRQ calls are added in ata_port_operations.
- irq_on() is used to enable interrupts.
- irq_ack() is used to acknowledge a device interrupt.

In most drivers, ata_irq_on() and ata_irq_ack() are used for
irq_on and irq_ack respectively.

In some drivers (ex: ahci, sata_sil24) which cannot use them
as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used.

Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:38 -05:00
Tejun Heo 0d5ff56677 libata: convert to iomap
Convert libata core layer and LLDs to use iomap.

* managed iomap is used.  Pointer to pcim_iomap_table() is cached at
  host->iomap and used through out LLDs.  This basically replaces
  host->mmio_base.

* if possible, pcim_iomap_regions() is used

Most iomap operation conversions are taken from Jeff Garzik
<jgarzik@pobox.com>'s iomap branch.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:38 -05:00
Tejun Heo 24dc5f33ea libata: update libata LLDs to use devres
Update libata LLDs to use devres.  Core layer is already converted to
support managed LLDs.  This patch simplifies initialization and fixes
many resource related bugs in init failure and detach path.  For
example, all converted drivers now handle ata_device_add() failure
gracefully without excessive resource rollback code.

As most resources are released automatically on driver detach, many
drivers don't need or can do with much simpler ->{port|host}_stop().
In general, stop callbacks are need iff port or host needs to be given
commands to shut it down.  Note that freezing is enough in many cases
and ports are automatically frozen before being detached.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:37 -05:00
Alan d73f30e1c9 sata_via: PATA support
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:30 -05:00
Jeff Garzik f20b16ff7c [libata] trim trailing whitespace
Most of these contributed by that mysterious figger known as A.C.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:29 -05:00
Tejun Heo d025987217 sata_via: style clean up, no indirect method call in LLD
Call ata_bmdma_irq_clear() directly instead of through
ap->ops->irq_clear() according to libata style guideline.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-01-26 17:24:07 -05:00
Tejun Heo 17234246eb sata_via: don't diddle with ATA_NIEN in ->freeze
vt6420 completely loses its ability to raise IRQ for ATAPI devices if
ATA_NIEN is diddled with in ->freeze.  Further investigation is
necessary to determine whether this problem is shared on other
controllers but it doesn't seem to be at this point.

Make vt6420's ->freeze only clear IRQ to fix this problem.  This makes
vt6420 relatively more prone to IRQ storms but the controller is way
too braindamaged to worry about that anyway.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-01-25 17:22:47 -05:00
Luca Pedrielli 96bc103f4c sata_via: add PCI ID 0x5337
Add PCI ID 0x5337 to supported PCI ID.  This is VT8237 in IDE mode.

Signed-off-by: Luca Pedrielli <luca.pedrielli@barradev.it>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-01-19 19:18:49 -05:00
Jeff Garzik 68ff6e8e0e [libata] sata_via: fix obvious typo
Spotted by Martin Devera.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-11-08 07:46:02 -05:00
Jeff Garzik 2d2744fc8b [libata] PCI ID table cleanup in various drivers
* Use PCI_VDEVICE() macro
* const-ify pci_device_id table
* standardize list terminator as "{ }"
* convert spaces to tab in pci_driver struct (Alan-ism)
* various minor whitespace cleanups

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-28 20:21:59 -04:00
Jeff Garzik 29da9f6d9c [libata] Fix oops introduced in non-uniform port handling fix
Noticed by several people.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-25 21:56:33 -04:00
Jeff Garzik cca3974e48 libata: Grand renaming.
The biggest change is that ata_host_set is renamed to ata_host.

* ata_host_set			=> ata_host
* ata_probe_ent->host_flags	=> ata_probe_ent->port_flags
* ata_probe_ent->host_set_flags	=> ata_probe_ent->_host_flags
* ata_host_stats		=> ata_port_stats
* ata_port->host		=> ata_port->scsi_host
* ata_port->host_set		=> ata_port->host
* ata_port_info->host_flags	=> ata_port_info->flags
* ata_(.*)host_set(.*)\(\)	=> ata_\1host\2()

The leading underscore in ata_probe_ent->_host_flags is to avoid
reusing ->host_flags for different purpose.  Currently, the only user
of the field is libata-bmdma.c and probe_ent itself is scheduled to be
removed.

ata_port->host is reused for different purpose but this field is used
inside libata core proper and of different type.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-08-24 03:19:22 -04:00
Jeff Garzik 54a86bfc3d Merge branch 'upstream-fixes' into upstream 2006-08-24 02:51:38 -04:00