Compared to other DSA switches, in the Ocelot cores, the RX filtering is
a much more important concern.
Firstly, the primary use case for Ocelot is non-DSA, so there isn't any
secondary Ethernet MAC [the DSA master's one] to implicitly drop frames
having a DMAC we are not interested in. So the switch driver itself
needs to install FDB entries towards the CPU port module (PGID_CPU) for
the MAC address of each switch port, in each VLAN installed on the port.
Every address that is not whitelisted is implicitly dropped. This is in
order to achieve a behavior similar to N standalone net devices.
Secondly, even in the secondary use case of DSA, such as illustrated by
Felix with the NPI port mode, that secondary Ethernet MAC is present,
but its RX filter is bypassed. This is because the DSA tags themselves
are placed before Ethernet, so the DMAC that the switch ports see is
not seen by the DSA master too (since it's shifter to the right).
So RX filtering is pretty important. A good RX filter won't bother the
CPU in case the switch port receives a frame that it's not interested
in, and there exists no other line of defense.
Ocelot is pretty strict when it comes to RX filtering: non-IP multicast
and broadcast traffic is allowed to go to the CPU port module, but
unknown unicast isn't. This means that traffic reception for any other
MAC addresses than the ones configured on each switch port net device
won't work. This includes use cases such as macvlan or bridging with a
non-Ocelot (so-called "foreign") interface. But this seems to be fine
for the scenarios that the Linux system embedded inside an Ocelot switch
is intended for - it is simply not interested in unknown unicast
traffic, as explained in Allan Nielsen's presentation [0].
On the other hand, the Felix DSA switch is integrated in more
general-purpose Linux systems, so it can't afford to drop that sort of
traffic in hardware, even if it will end up doing so later, in software.
Actually, unknown unicast means more for Felix than it does for Ocelot.
Felix doesn't attempt to perform the whitelisting of switch port MAC
addresses towards PGID_CPU at all, mainly because it is too complicated
to be feasible: while the MAC addresses are unique in Ocelot, by default
in DSA all ports are equal and inherited from the DSA master. This adds
into account the question of reference counting MAC addresses (delayed
ocelot_mact_forget), not to mention reference counting for the VLAN IDs
that those MAC addresses are installed in. This reference counting
should be done in the DSA core, and the fact that it wasn't needed so
far is due to the fact that the other DSA switches don't have the DSA
tag placed before Ethernet, so the DSA master is able to whitelist the
MAC addresses in hardware.
So this means that even regular traffic termination on a Felix switch
port happens through flooding (because neither Felix nor Ocelot learn
source MAC addresses from CPU-injected frames).
So far we've explained that whitelisting towards PGID_CPU:
- helps to reduce the likelihood of spamming the CPU with frames it
won't process very far anyway
- is implemented in the ocelot driver
- is sufficient for the ocelot use cases
- is not feasible in DSA
- breaks use cases in DSA, in the current status (whitelisting enabled
but no MAC address whitelisted)
So the proposed patch allows unknown unicast frames to be sent to the
CPU port module. This is done for the Felix DSA driver only, as Ocelot
seems to be happy without it.
[0]: https://www.youtube.com/watch?v=B1HhxEcU7Jg
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot has the concept of a CPU port. The CPU port is represented in the
forwarding and the queueing system, but it is not a physical device. The
CPU port can either be accessed via register-based injection/extraction
(which is the case of Ocelot), via Frame-DMA (similar to the first one),
or "connected" to a physical Ethernet port (called NPI in the datasheet)
which is the case of the Felix DSA switch.
In Ocelot the CPU port is at index 11.
In Felix the CPU port is at index 6.
The CPU bit is treated special in the forwarding, as it is never cleared
from the forwarding port mask (once added to it). Other than that, it is
treated the same as a normal front port.
Both Felix and Ocelot should use the CPU port in the same way. This
means that Felix should not use the NPI port directly when forwarding to
the CPU, but instead use the CPU port.
This patch is fixing this such that Felix will use port 6 as its CPU
port, and just use the NPI port to carry the traffic.
Therefore, eliminate the "ocelot->cpu" variable which was holding the
index of the NPI port for Felix, and the index of the CPU port module
for Ocelot, so the variable was actually configuring different things
for different drivers and causing at least part of the confusion.
Also remove the "ocelot->num_cpu_ports" variable, which is the result of
another confusion. The 2 CPU ports mentioned in the datasheet are
because there are two frame extraction channels (register based or DMA
based). This is of no relevance to the driver at the moment, and
invisible to the analyzer module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the cls_flower methods from the ocelot driver and hook them up to
the DSA passthrough layer.
Tables for the VCAP IS2 parameters, as well as half key packing (field
offsets and lengths) need to be defined for the VSC9959 core, as they
are different from Ocelot, mainly due to the different port count.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the definitions for the VCAP IS2 table from ocelot_ace.c, since
it is specific to VSC7514.
The VSC9959 VCAP IS2 table supports more rules (1024 instead of 64) and
has a different width for the action (89 bits instead of 99).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix driver is now using its own PHYLINK instance, not calling into
ocelot_adjust_link. So the port_pcs_init function pointer is an
unnecessary indirection. Remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IGR_PORT_MASK key width is different between the 11-port VSC7514 and
the 6-port VSC9959 switches. And since IGR_PORT_MASK is one of the first
fields of a VCAP key entry, it means that all further field
offset/length pairs are shifted between the 2.
The ocelot driver performs packing of VCAP half keys with the help of
some preprocessor macros:
- A set of macros for defining the HKO (Half Key Offset) and HKL (Half
Key Length) of each possible key field. The offset of each field is
defined as the sum between the offset and the sum of the previous
field.
- A set of accessors on top of vcap_key_set for shorter (aka less
typing) access to the HKO and HKL of each key field.
Since the field offsets and lengths are different between switches,
defining them through the preprocessor isn't going to fly. So introduce
a structure holding (offset, length) pairs and instantiate it in
ocelot_board.c for VSC7514. In a future patch, a similar structure will
be instantiated in felix_vsc9959.c for NXP LS1028A.
The accessors also need to go. They are based on macro name
concatenation, which is horrible to understand and follow.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot tc-flower offload binds a second flow block callback (apart
from the one for matchall) just because it uses a different block
private structure (ocelot_port_private for matchall, ocelot_port_block
for flower).
But ocelot_port_block just appears to be boilerplate, and doesn't help
with anything in particular at all, it's just useless glue between the
(global!) struct ocelot_acl_block *block pointer, and a per-netdevice
struct ocelot_port_private *priv.
So let's just simplify that, and make struct ocelot_port_private be the
private structure for the block offload. This makes us able to use the
same flow callback as in the case of matchall.
This also reveals that the struct ocelot_acl_block *block is used rather
strangely, as mentioned above: it is defined globally, allocated at
probe time, and freed at unbind time. So just move the structure to the
main ocelot structure, which gives further opportunity for
simplification.
Also get rid of backpointers from struct ocelot_acl_block and struct
ocelot_ace_rule back to struct ocelot, by reworking the function
prototypes, where necessary, to use a more DSA-friendly "struct ocelot
*ocelot, int port" format.
And finally, remove the debugging prints that were added during
development, since they provide no useful information at this point.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl4+lTYPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3nQcQAJm91+6hZbmMjlBySGS7ISjYvOcrI/hMgiOl
uhhEP0Dcylvf9A9x3wcIbLwixe+2pvie9DQh2u5F80ShYimidtFi/2xCfuTb9fKu
sxxKjrXWyVKhkpW0z+tedY08ftVhkwwcyD4m2C7uVl6AwTP7c367vFeU7XjF2APn
drfgmgbjm8U3XbSyAqv+k6z6tyqaCnFM7vbPupSKHgHJ3mfByxOa+XyBN2RdgBbs
0KrVfbXGv80zFIFrMPwaWG7G52bu7K68nVdgy44MpKdRZ6QTjhnR+kerFxHsYgV4
bM55Fya52nTCSTGdKaQakDtKwbAUdCDTSkxgOHGcQoyFi0R/VaEUJtcysnvLbI6c
+n/yFIzGyEdXcvIzfv2SoDYhogw19I6RR/M9K5Ni29eazkDVYx2z3rI+2QYeqCiF
u7cq52gW6JLP0SI/9kuUrRFiR8v19Ixap7qokAxgqQwYB3NzT8a7WsYPkzdpDZGQ
ETSDFMyBWT6UvBe/HWkQluBabbet53rG8BF0OHFrQuMK0u/ieKgSGuTB9XN2djEW
PHMOMz2vhi+8XTfpkskhF2tTxlA/k4R6QwCdIMpIkMRVnVQCh1XdPr3Fi2NrgB+S
kIXHD4vV6zLYh04zHyKewSPHAXWgraFpg2qKnvL5+KWMTnW6QH+RNjOt9xKDNXOd
+iDXpOad
=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
The commit 9209fb5189 ("riscv: move sifive_l2_cache.c to drivers/soc")
moves the sifive L2 cache driver to driver/soc. It did not move the
header file along with the driver. Therefore this patch moves the header
file to driver/soc
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
[paul.walmsley@sifive.com: updated to fix the include guard]
Fixes: 9209fb5189 ("riscv: move sifive_l2_cache.c to drivers/soc")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Since the Felix DSA driver is implementing its own PHYLINK instance due
to SoC differences, it needs access to the few registers that are
common, mainly for flow control.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ocelot switchdev driver and the Felix DSA one need it for different
reasons. Felix (or at least the VSC9959 instantiation in NXP LS1028A) is
integrated with the traditional NXP Layerscape PCS design which does not
support runtime configuration of SerDes protocol. So it needs to
pre-validate the phy-mode from the device tree and prevent PHYLINK from
attempting to change it. For this, it needs to cache it in a private
variable.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building this on a 64-bit platform gcc rightly warns that the
error checking is broken (-ENOMEM stored in an u32 does not compare
greater than (unsigned long)-MAX_ERRNO). Instead, change the
ucc_fast_[tr]x_virtual_fifo_base_offset members to s32 and use an
ordinary check-for-negative. Also, this avoids treating 0 as "this
cannot have been returned from qe_muram_alloc() so don't free it".
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
When trying to build this for a 64-bit platform, one gets warnings
from using IS_ERR_VALUE on something which is not sizeof(long).
Instead, change the various *_offset fields to store a signed integer,
and simply check for a negative return from qe_muram_alloc(). Since
qe_muram_free() now accepts and ignores a negative argument, we only
need to make sure these fields are initialized with -1, and we can
just unconditionally call qe_muram_free() in ucc_slow_free().
Note that the error case for us_pram_offset failed to set that field
to 0 (which, as noted earlier, is anyway a bogus sentinel value).
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Nobody uses the return value from cpm_muram_free, and functions that
free resources usually return void. One could imagine a use for a "how
much have I allocated" a la ksize(), but knowing how much one had
access to after the fact is useless.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
There are a number of problems with cpm_muram_alloc() and its
callers. Most callers assign the return value to some variable and
then use IS_ERR_VALUE to check for allocation failure. However, when
that variable is not sizeof(long), this leads to warnings - and it is
indeed broken to do e.g.
u32 foo = cpm_muram_alloc();
if (IS_ERR_VALUE(foo))
on a 64-bit platform, since the condition
foo >= (unsigned long)-ENOMEM
is tautologically false. There are also callers that ignore the
possibility of error, and then there are those that check for error by
comparing the return value to 0...
One could fix that by changing all callers to store the return value
temporarily in an "unsigned long" and test that. However, use of
IS_ERR_VALUE() is error-prone and should be restricted to things which
are inherently long-sized (stuff in pt_regs etc.). Instead, let's aim
for changing to the standard kernel style
int foo = cpm_muram_alloc();
if (foo < 0)
deal_with_it()
some->where = foo;
Changing the return type from unsigned long to s32 (aka signed int)
doesn't change the value that gets stored into any of the callers'
variables except if the caller was storing the result in a u64 _and_
the allocation failed, so in itself this patch should be a no-op.
Another problem with cpm_muram_alloc() is that it can certainly
validly return 0 - and except if some cpm_muram_alloc_fixed() call
interferes, the very first cpm_muram_alloc() call will return just
that. But that shows that both ucc_slow_free() and ucc_fast_free() are
buggy, since they assume that a value of 0 means "that field was never
allocated". We'll later change cpm_muram_free() to accept (and ignore)
a negative offset, so callers can use a sentinel of -1 instead of 0
and just unconditionally call cpm_muram_free().
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
asm/cpm.h under arch/powerpc is now just a wrapper for including
soc/fsl/cpm.h. In order to make the qe.h header usable on other
architectures, use the latter path directly.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Some drivers, e.g. ucc_uart, need definitions from cpm.h. In order to
allow building those drivers for non-ppc based SOCs, move the header
to include/soc/fsl. For now, leave a trivial wrapper at the old
location so drivers can be updated one by one.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The public qe_ic.h header is no longer included by anything but
qe_ic.c. Merge both headers into qe_ic.c, and drop the unused
constants.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
These are only called from within qe_ic.c, so make them static.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
There are no current callers of these functions, and they use the
ppc-specific virq_to_hw(). So removing them gets us one step closer to
building QE support for ARM.
If the functionality is ever actually needed, the code can be dug out
of git and then adapted to work on all architectures, but for future
reference please note that I believe qe_ic_set_priority is buggy: The
"priority < 4" should be "priority <= 4", and in the else branch 24
should be replaced by 28, at least if I'm reading the data sheet right.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
These functions are only ever called through a function pointer, and
therefore it makes no sense for them to be "static inline" - gcc has
no choice but to emit a copy in each translation unit that takes the
address of one of these. Since they are now only referenced from
qe_ic.c, just make them local to that file.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Having to call qe_ic_init() from platform-specific code makes it
awkward to allow building the QE drivers for ARM. It's also a needless
duplication of code, and slightly error-prone: Instead of the caller
needing to know the details of whether the QUICC Engine High and QUICC
Engine Low are actually the same interrupt (see e.g. the machine_is()
in mpc85xx_mds_qeic_init), just let the init function choose the
appropriate handlers after it has parsed the DT and figured it out. If
the two interrupts are distinct, use separate handlers, otherwise use
the handler which first checks the CHIVEC register (for the high
priority interrupts), then the CIVEC.
All existing callers pass 0 for flags, so continue to do that from the
new single caller. Later cleanups will remove that argument
from qe_ic_init and simplify the body, as well as make qe_ic_init into
a proper init function for an IRQCHIP_DECLARE, eliminating the need to
manually look up the fsl,qe-ic node.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The *_ipic and *_mpic handlers are almost identical - the only
difference is that the latter end with an unconditional
chip->irq_eoi() call. Since IPIC does not have ->irq_eoi, we can
reduce some code duplication by calling irq_eoi conditionally.
This is similar to what is already done in mpc8xxx_gpio_irq_cascade().
This leaves the functions slightly misnamed, but that will be fixed in
a subsequent patch.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The QUICC engine drivers use the powerpc-specific out_be32() etc. In
order to allow those drivers to build for other architectures, those
must be replaced by iowrite32be(). However, on powerpc, out_be32() is
a simple inline function while iowrite32be() is out-of-line. So in
order not to introduce a performance regression on powerpc when making
the drivers work on other architectures, introduce qe_io* helpers.
Also define the qe_{clr,set,clrset}bits* helpers in terms of these new
macros.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Make it clear that these operate on big-endian registers (i.e. use the
iowrite*be primitives) before we introduce more uses of them and allow
the QE drivers to be built for platforms other than ppc32.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
msm-next:
- OCMEM support for a3xx and a4xx GPUs.
- a510 support + display support
core:
- mst payload deletion fix
i915:
- uapi alignment fix
- fix for power usage regression due to security fixes
- change default preemption timeout to 640ms from 100ms
- EHL voltage level display fixes
- TGL DGL PHY fix
- gvt - MI_ATOMIC cmd parser fix, CFL non-priv warning
- CI spotted deadlock fix
- EHL port D programming fix
amdgpu:
- VRAM lost fixes on BACO for CI/VI
- navi14 DC fixes
- misc SR-IOV, gfx10 fixes
- XGMI fixes for arcturus
- SRIOV fixes
amdkfd:
- KFD on ppc64le enabled
- page table optimisations
radeon:
- fix for r1xx/2xx register checker.
tegra:
- displayport regression fixes
- DMA API regression fixes
mgag200:
- fix devices that can't scanout except at 0 addr
omap:
- fix dma_addr refcounting
-----BEGIN PGP SIGNATURE-----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=3cs2
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-12-06' of git://anongit.freedesktop.org/drm/drm
Pull more drm updates from Dave Airlie:
"Rob pointed out I missed his pull request for msm-next, it's been in
next for a while outside of my tree so shouldn't cause any unexpected
issues, it has some OCMEM support in drivers/soc that is acked by
other maintainers as it's outside my tree.
Otherwise it's a usual fixes pull, i915, amdgpu, the main ones, with
some tegra, omap, mgag200 and one core fix.
Summary:
msm-next:
- OCMEM support for a3xx and a4xx GPUs.
- a510 support + display support
core:
- mst payload deletion fix
i915:
- uapi alignment fix
- fix for power usage regression due to security fixes
- change default preemption timeout to 640ms from 100ms
- EHL voltage level display fixes
- TGL DGL PHY fix
- gvt - MI_ATOMIC cmd parser fix, CFL non-priv warning
- CI spotted deadlock fix
- EHL port D programming fix
amdgpu:
- VRAM lost fixes on BACO for CI/VI
- navi14 DC fixes
- misc SR-IOV, gfx10 fixes
- XGMI fixes for arcturus
- SRIOV fixes
amdkfd:
- KFD on ppc64le enabled
- page table optimisations
radeon:
- fix for r1xx/2xx register checker.
tegra:
- displayport regression fixes
- DMA API regression fixes
mgag200:
- fix devices that can't scanout except at 0 addr
omap:
- fix dma_addr refcounting"
* tag 'drm-next-2019-12-06' of git://anongit.freedesktop.org/drm/drm: (100 commits)
drm/dp_mst: Correct the bug in drm_dp_update_payload_part1()
drm/omap: fix dma_addr refcounting
drm/tegra: Run hub cleanup on ->remove()
drm/tegra: sor: Make the +5V HDMI supply optional
drm/tegra: Silence expected errors on IOMMU attach
drm/tegra: vic: Export module device table
drm/tegra: sor: Implement system suspend/resume
drm/tegra: Use proper IOVA address for cursor image
drm/tegra: gem: Remove premature import restrictions
drm/tegra: gem: Properly pin imported buffers
drm/tegra: hub: Remove bogus connection mutex check
ia64: agp: Replace empty define with do while
agp: Add bridge parameter documentation
agp: remove unused variable num_segments
agp: move AGPGART_MINOR to include/linux/miscdevice.h
agp: remove unused variable size in agp_generic_create_gatt_table
drm/dp_mst: Fix build on systems with STACKTRACE_SUPPORT=n
drm/radeon: fix r1xx/r2xx register checker for POT textures
drm/amdgpu: fix GFX10 missing CSIB set(v3)
drm/amdgpu: should stop GFX ring in hw_fini
...
Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo
-----BEGIN PGP SIGNATURE-----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=dk7w
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
Convert to use skb queue instead of the list of skbs.
The skb queue could provide protection with lock.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to use ocelot_port_add_txtstamp_skb() for adding skbs which
require TX timestamp into list. Export it so that DSA Felix driver
could reuse it too.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method getting TX timestamp by reading timestamp FIFO and
matching skbs list is common for DSA Felix driver too.
So move code out of ocelot_board.c, convert to use
ocelot_get_txtstamp() function and export it.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export ocelot_hwstamp_get/set functions so that DSA driver
is able to reuse them.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix DSA driver needs to write to SYS_RAM_INIT_RAM_INIT for its own
chip initialization process.
Also update the MAINTAINERS file such that the headers exported by the
ocelot driver are under the same maintainers' umbrella as the driver
itself.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will be registering another switch driver based on ocelot, which
lives under drivers/net/dsa.
Make sure the Felix DSA front-end has the necessary abstractions to
implement a new Ocelot driver instantiation. This includes the function
prototypes for implementing DSA callbacks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce driver for the External Memory Controller (EMC) found on Tegra30
chips, it controls the external DRAM on the board. The purpose of this
driver is to program memory timing for external memory on the EMC clock
rate change.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Before this change, unbinding the QMan portals did not trigger a
corresponding unbinding of the dpaa_eth making use of it; the first
QMan portal related operation issued afterwards crashed the kernel.
The device link ensures the dpaa_eth dependency upon the qman portal
used is honoured at the QMan portal removal.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the API required to make sure that the devices that use
the QMan portal are unbound when the portal is unbound.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kbuild bot reported the following compiler errors when compiling on
MIPS with CONFIG_QCOM_OCMEM disabled:
In file included from <command-line>:0:0:
>> include/soc/qcom/ocmem.h:43:49: warning: 'struct device' declared
inside parameter list will not be visible outside of this
definition or declaration
static inline struct ocmem *of_get_ocmem(struct device *dev)
^~~~~~
include/soc/qcom/ocmem.h: In function 'of_get_ocmem':
>> include/soc/qcom/ocmem.h:45:9: error: implicit declaration of
function 'ERR_PTR' [-Werror=implicit-function-declaration]
return ERR_PTR(-ENODEV);
^~~~~~~
>> include/soc/qcom/ocmem.h:45:18: error: 'ENODEV' undeclared (first
use in this function)
return ERR_PTR(-ENODEV);
Add the proper includes to fix the compiler errors.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reported-by: kbuild test robot <lkp@intel.com>
Tested-by: Gabriel Francisco <frc.gabriel@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The OCMEM driver handles allocation and configuration of the On Chip
MEMory that is present on some Snapdragon SoCs. Devices which have
OCMEM do not have GMEM inside the GPU core, so the GPU must instead
use OCMEM to be functional. Since the GPU is currently the only OCMEM
user with an upstream driver, this is just a minimal implementation
sufficient for statically allocating to the GPU it's chunk of OCMEM.
This driver currently does not read the gmu-sram node that is described
in the device tree bindings. The starting memory address of the GPU's
reserved memory region is hardcoded to zero to match what the hardware
expects. The driver can be updated to read the reserved memory regions
from device tree once other users of OCMEM are added upstream.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Co-developed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Gabriel Francisco <frc.gabrielgmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Here is the big char/misc driver pull request for 5.4-rc1.
As has been happening in previous releases, more and more individual
driver subsystem trees are ending up in here. Now if that is good or
bad I can't tell, but hopefully it makes your life easier as it's more
of an aggregation of trees together to one merge point for you.
Anyway, lots of stuff in here:
- habanalabs driver updates
- thunderbolt driver updates
- misc driver updates
- coresight and intel_th hwtracing driver updates
- fpga driver updates
- extcon driver updates
- some dma driver updates
- char driver updates
- android binder driver updates
- nvmem driver updates
- phy driver updates
- parport driver fixes
- pcmcia driver fix
- uio driver updates
- w1 driver updates
- configfs fixes
- other assorted driver updates
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIT1g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym9lwCgrHZlMMvfYNVm6GQ5ge58JJsVTL4AoNatTcL4
hfVMA6pCHWBjV65xVSf6
=Tijw
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver pull request for 5.4-rc1.
As has been happening in previous releases, more and more individual
driver subsystem trees are ending up in here. Now if that is good or
bad I can't tell, but hopefully it makes your life easier as it's more
of an aggregation of trees together to one merge point for you.
Anyway, lots of stuff in here:
- habanalabs driver updates
- thunderbolt driver updates
- misc driver updates
- coresight and intel_th hwtracing driver updates
- fpga driver updates
- extcon driver updates
- some dma driver updates
- char driver updates
- android binder driver updates
- nvmem driver updates
- phy driver updates
- parport driver fixes
- pcmcia driver fix
- uio driver updates
- w1 driver updates
- configfs fixes
- other assorted driver updates
All of these have been in linux-next for a long time with no reported
issues"
* tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (200 commits)
misc: mic: Use PTR_ERR_OR_ZERO rather than its implementation
habanalabs: correctly cast variable to __le32
habanalabs: show correct id in error print
habanalabs: stop using the acronym KMD
habanalabs: display card name as sensors header
habanalabs: add uapi to retrieve aggregate H/W events
habanalabs: add uapi to retrieve device utilization
habanalabs: Make the Coresight timestamp perpetual
habanalabs: explicitly set the queue-id enumerated numbers
habanalabs: print to kernel log when reset is finished
habanalabs: replace __le32_to_cpu with le32_to_cpu
habanalabs: replace __cpu_to_le32/64 with cpu_to_le32/64
habanalabs: Handle HW_IP_INFO if device disabled or in reset
habanalabs: Expose devices after initialization is done
habanalabs: improve security in Debug IOCTL
habanalabs: use default structure for user input in Debug IOCTL
habanalabs: Add descriptive name to PSOC app status register
habanalabs: Add descriptive names to PSOC scratch-pad registers
habanalabs: create two char devices per ASIC
habanalabs: change device_setup_cdev() to be more generic
...
Here are the interconnect driver updates for the 5.4-rc1 merge window.
- New feature is the path tagging support that helps with grouping and
aggregating the bandwidth requests into separate buckets based on a tag.
- The first user of the path tagging is the Qualcomm sdm845 driver that
now implements support for wake/sleep sets. This allows consumer drivers
to express their bandwidth needs for the different CPU power states.
- New interconnect driver for the qcs404 platforms and a driver that
communicates bandwidth requests with remote processor over shared memory.
- Cleanups and fixes.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
-----BEGIN PGP SIGNATURE-----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=TVC/
-----END PGP SIGNATURE-----
Merge tag 'icc-5.4-rc1' of https://git.linaro.org/people/georgi.djakov/linux into char-misc-next
Georgi writes:
interconnect patches for 5.4
Here are the interconnect driver updates for the 5.4-rc1 merge window.
- New feature is the path tagging support that helps with grouping and
aggregating the bandwidth requests into separate buckets based on a tag.
- The first user of the path tagging is the Qualcomm sdm845 driver that
now implements support for wake/sleep sets. This allows consumer drivers
to express their bandwidth needs for the different CPU power states.
- New interconnect driver for the qcs404 platforms and a driver that
communicates bandwidth requests with remote processor over shared memory.
- Cleanups and fixes.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
* tag 'icc-5.4-rc1' of https://git.linaro.org/people/georgi.djakov/linux:
drivers: qcom: Add BCM vote macro to header
interconnect: qcom: remove COMPILE_TEST from CONFIG_INTERCONNECT_QCOM_QCS404
interconnect: qcom: Add QCS404 interconnect provider driver
interconnect: qcom: Add interconnect RPM over SMD driver
dt-bindings: interconnect: Add Qualcomm QCS404 DT bindings
interconnect: qcom: Add tagging and wake/sleep support for sdm845
interconnect: Add pre_aggregate() callback
interconnect: Add support for path tags
Remove the "struct mtk_smi_iommu" to simplify the code since it has only
one item in it right now.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The "mediatek,larb-id" has already been parsed in MTK IOMMU driver.
It's no need to parse it again in SMI driver. Only clean some codes.
This patch is fit for all the current mt2701, mt2712, mt7623, mt8173
and mt8183.
After this patch, the "mediatek,larb-id" only be needed for mt2712
which have 2 M4Us. In the other SoCs, we can get the larb-id from M4U
in which the larbs in the "mediatek,larbs" always are ordered.
Correspondingly, the larb_nr in the "struct mtk_smi_iommu" could also
be deleted.
CC: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
- Support for Edge Triggered IRQs in ARC IDU intc
- other fixes here and there
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CJKr
-----END PGP SIGNATURE-----
Merge tag 'arc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- support for Edge Triggered IRQs in ARC IDU intc
- other fixes here and there
* tag 'arc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
arc: prefer __section from compiler_attributes.h
dt-bindings: IDU-intc: Add support for edge-triggered interrupts
dt-bindings: IDU-intc: Clean up documentation
ARCv2: IDU-intc: Add support for edge-triggered interrupts
ARC: unwind: Mark expected switch fall-throughs
ARC: [plat-hsdk]: allow to switch between AXI DMAC port configurations
ARC: fix typo in setup_dma_ops log message
ARCv2: entry: early return from exception need not clear U & DE bits
This adds support for an optional extra interrupt cell to specify edge
vs level triggered. It is backward compatible with dts files with only
one cell, and will default to level-triggered in such a case.
Note that I had to make a change to idu_irq_set_affinity as well, as
this function was setting the interrupt type to "level" unconditionally,
since this was the only type supported previously.
Signed-off-by: Mischa Jonker <mischa.jonker@synopsys.com>
Reviewed-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The macro to generate a Bus Controller Manager (BCM) TCS command is used
by the interconnect driver but might also be interesting to other
drivers that need to construct TCS commands for sub processors so move
it out of the sdm845 specific file and into the header.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework
-----BEGIN PGP SIGNATURE-----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=ek+j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (84 commits)
reset: remove redundant null check on pointer dev
soc: rockchip: work around clang warning
dt-bindings: reset: imx7: Fix the spelling of 'indices'
soc: imx: Add i.MX8MN SoC driver support
soc: aspeed: lpc-ctrl: Fix probe error handling
soc: qcom: geni: Add support for ACPI
firmware: ti_sci: Fix gcc unused-but-set-variable warning
firmware: ti_sci: Use the correct style for SPDX License Identifier
soc: imx8: Use existing of_root directly
soc: imx8: Fix potential kernel dump in error path
firmware/psci: psci_checker: Park kthreads before stopping them
memory: move jedec_ddr.h from include/memory to drivers/memory/
memory: move jedec_ddr_data.c from lib/ to drivers/memory/
MAINTAINERS: Remove myself as qcom maintainer
soc: aspeed: lpc-ctrl: make parameter optional
soc: qcom: apr: Don't use reg for domain id
soc: qcom: fix QCOM_AOSS_QMP dependency and build errors
memory: tegra: Fix -Wunused-const-variable
firmware: tegra: Early resume BPMP
soc/tegra: Select pinctrl for Tegra194
...
Convert docs to ReST and add them to the arch-specific
book.
The conversion here was trivial, as almost every file there
was already using an elegant format close to ReST standard.
The changes were mostly to mark literal blocks and add a few
missing section title identifiers.
One note with regards to "--": on Sphinx, this can't be used
to identify a list, as it will format it badly. This can be
used, however, to identify a long hyphen - and "---" is an
even longer one.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> # cxl
Vladimir Oltean
Linus Torvalds
David S. Miller
Yash Shah
Rasmus Villemoes
Yangbo Lu
Dmitry Osipenko
Madalin Bucur
Brian Masney
Joerg Roedel
Greg Kroah-Hartman
Yong Wu
Mischa Jonker
Jordan Crouse
Jonathan Corbet
Mauro Carvalho Chehab