Set DMA max seg size correctly to get rid of warnings on 64 bit
platforms:
DMA-API: cal 6f03000.cal: mapping sg segment longer than device claims to support [len=720896] [max=65536]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAL_CSI2_CTX register has LINES field, which, according to the
documentation, should be programmed to the number of lines transmitted
by the camera. If the number of lines is unknown, it can be set to 0.
The driver sets the field to 0 for some reason, even if we know the
number of lines.
This patch sets the number of lines properly, which will allow the HW to
discard extra lines (if the sensor would send such for some reason),
and, according to documentation: "This leads to regular video timings
and avoids potential artifacts".
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After ComplexIO reset, a dummy read to PHY is needed as per CAL spec to
finish the reset. Currently the driver reads a ComplexIO register, not
PHY register. Fix this.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move the code to enable and disable ComplexIO power to its own function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Simplify the code by using reg_write_field() where trivially possible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove a bunch of IRQ defines, of which only CAL_HL_IRQ_ENABLE and
CAL_HL_IRQ_CLEAR are used, and these defines only end up obfuscating
code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
These macros only obfuscate the code, so drop them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of having identical code block to handle irqs for the two CAL
ports, we can have a for loop and a single code block.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver does not print any errors on ComplexIO reset timeout or when
waiting for stop-state, making it difficult to debug and notice
problems.
Add error prints for these cases.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAL reports various errors via IRQs, which are not handled at all by the
current driver. Add code to enable and catch those IRQs and print
errors. This will make it much easier to notice and debug issues with
sensors.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix: spaces preferred around that '-']
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Now that cal_runtime_get and cal_runtime_put are only direct wrappers to
pm_runtime_get/put, we can drop cal_runtime_get and cal_runtime_put.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We need to do errata handling every time CAL is being enabled. The code
is currently in cal_runtime_get(), which is not the correct place for
it.
Move the code to cal_runtime_resume, which is called every time CAL is
enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
i913_errata() sets a bit to 1 in PHY_REG10, but for some reason uses
CAL_CSI2_PHY_REG0_HSCLOCKCONFIG_DISABLE for the bit value. The value of
that macro is 1, so it works, but is still wrong.
Fix this to 1.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IRQENABLE_SET registers are (usually) not meant to be read, only written
to. The current driver needlessly uses read-modify-write cycle to enable
IRQ bits.
The read-modify-write has no bad side effects here, but it's still
better to clean this up by only using write.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the CAL driver stops streaming, it will shut everything down
without waiting for the current frame to finish. This leaves the CAL DMA
in a slightly undefined state, and when CAL DMA is enabled when the
stream is started the next time, the old DMA transfer will continue.
It is not clear if the old DMA transfer continues with the exact
settings of the original transfer, or is it a mix of old and new
settings, but in any case the end result is memory corruption as the
destination memory address is no longer valid.
I could not find any way to ensure that any old DMA transfer would be
discarded, except perhaps full CAL reset. But we cannot do a full reset
when one port is getting enabled, as that would reset both ports.
This patch tries to make sure that the DMA transfer is finished properly
when the stream is being stopped. I say "tries", as, as mentioned above,
I don't see a way to force the DMA transfer to finish. I believe this
fixes the corruptions for normal cases, but if for some reason the DMA
of the final frame would stall a lot, resulting in timeout in the code
waiting for the DMA to finish, we'll again end up with unfinished DMA
transfer. However, I don't know what could cause such a timeout.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Venus driver is voting Configuration NoC during .probe but not clear
voting in .suspend. Because of this NoC is up during shutdown also. As a
consequence the whole device could leak energy while in .suspend.
So correct this by moving voting in .resume and unvoting
in .suspend
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement pmruntime autosuspend in video decoder. This will
allow to save power while the userspace is inactive for some
reasonable period of time. Here we power-off venus core clocks
and power domain and don't touch vcodec because it is under
hardware control. The later decision is made to simplify the
code and avoid a mess in the power management code.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
v4l2_ctrl_handler_free() uses hdl->lock, which in ov5640 driver is set
to sensor's own sensor->lock. In ov5640_remove(), the driver destroys the
sensor->lock first, and then calls v4l2_ctrl_handler_free(), resulting
in the use of the destroyed mutex.
Fix this by calling moving the mutex_destroy() to the end of the cleanup
sequence, as there's no need to destroy the mutex as early as possible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org # v4.14+
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are several markups there that doesn't follow the
specs. Fields should be like:
@foo:
with a collon at the end. Also, continuation lines should
be aligned.
Failing to do that would cause kernel-doc to parse it wrong.
Some of the troubles will even cause warnings:
$ ./scripts/kernel-doc -none drivers/media/test_drivers/vimc/vimc-common.h
drivers/media/test_drivers/vimc/vimc-common.h:59: error: Cannot parse struct or union!
drivers/media/test_drivers/vimc/vimc-common.h:77: warning: Function parameter or member 'bpp' not described in 'vimc_pix_map'
drivers/media/test_drivers/vimc/vimc-common.h:120: warning: Function parameter or member 'pipe_cfg' not described in 'vimc_device'
drivers/media/test_drivers/vimc/vimc-common.h:120: warning: Function parameter or member 'ent_devs' not described in 'vimc_device'
drivers/media/test_drivers/vimc/vimc-common.h:120: warning: Function parameter or member 'mdev' not described in 'vimc_device'
drivers/media/test_drivers/vimc/vimc-common.h:120: warning: Function parameter or member 'v4l2_dev' not described in 'vimc_device'
drivers/media/test_drivers/vimc/vimc-common.h:137: warning: Function parameter or member 'add' not described in 'vimc_ent_type'
drivers/media/test_drivers/vimc/vimc-common.h:137: warning: Function parameter or member 'unregister' not described in 'vimc_ent_type'
drivers/media/test_drivers/vimc/vimc-common.h:137: warning: Function parameter or member 'release' not described in 'vimc_ent_type'
drivers/media/test_drivers/vimc/vimc-common.h:150: warning: Function parameter or member 'name' not described in 'vimc_ent_config'
drivers/media/test_drivers/vimc/vimc-common.h:150: warning: Function parameter or member 'type' not described in 'vimc_ent_config'
drivers/media/test_drivers/vimc/vimc-common.h:197: warning: bad line: flags of the pads
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This spinlock is used solely to call v4l2_m2m_buf_done().
Since buffers are obtained only after being removed
from the ready queue, there's no concurrent access, and
so no need for synchronization.
Remove the spinlock to make sure no one copies this pattern.
Some archaeology shows this is a small leftover from ancient code.
This driver (then called m2m_testdev) used the videobuf1 framework;
commit d80ee38cd8 ("[media] v4l: mem2mem: port m2m_testdev to vb2")
converted it to videobuf2. The spinlock was then no longer needed,
and this simply went unnoticed.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since each vimc entity type is defined by the
callbacks implementation, it is a good idea to
add a struct to hold these callbacks.
Each vimc entity then declare its type in the file for
the entity.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are some missing and extra fields and typos in
structs documentations in vimc-common.h. Fix it.
[mchehab+huawei@kernel.org: add a missing ':' after @bayer field]
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently when the 'add' callback of an entity fails, a
NULL is returned. This hides the error code of the failure
and always returns -EINVAL.
Replace return NULL with return ERR_PTR(ret) to improve debugging.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In case the 'add' callback of an entity fails,
then all other entities should unregister and released.
This should be done inside vimc_add_subdevs so that
the function handles its own failure.
In order to call vimc_unregister_subdevs and vimc_release_subdevs from
vimc_add_subdevs, the order of the function should change.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The function vimc_unregister is called only from
one place in the code and has only 3 lines so it
has no justification.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Each jpeg can have the huffman tables optimized for its specific content
meaning that the table lenghts and values don't match the standard table
of substitutions so there's no reason to hardcode and expect the standard
lengths, otherwise we just end up rejecting optimized jpegs altogether.
Tested on CODA960.
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Similar to commit 9ee50a9489 ("media: coda: lock capture queue wakeup
against encoder stop command"), make sure that a JPEG decoder stop
command running concurrently with a decoder finish_run always either
flags the last returned buffer or wakes up the capture queue to signal
the end of stream condition afterwards.
This was not necessary for BIT processor contexts because of the need to
release the bitstream buffer with the stream end condition. In contrast,
the JPEG decoder can be finished with decoding the image between the
time the application queues the last output buffer and the time it
issues the decoder stop command.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If a JPEG decoding application queues the last capture and output
buffers, issues a decoder stop command after the decoding is already
done, and then dequeues the last capture buffer, it is not marked as
last. Detect this condition in the decoder stop command and mark the
last buffer on the capture done list.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Split marking the last metadata entry into a helper function to simplify
coda_decoder_cmd.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch adds JPEG decoding support for CODA960, handling the JPEG
hardware directly. A separate JPEG decoder video device is created due
to the separate hardware unit and different supported pixel formats.
While the hardware can not change subsampling on the fly, it can decode
4:2:2 subsampled JPEG images into YUV422P.
[m.felsch@pengutronix.de: fix qsequence counting by explicitly
checking for the !use_bit case]
[hverkuil-cisco@xs4all.nl: fix 'warning: missing braces around initializer']
[mchehab+huawei@kernel.org: fix 'BRACES: Unbalanced braces around else statement']
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add helpers for JPEG header parsing. They allow both scanning for marker
segment positions and later parsing the segments individually, as
required by s5p-jpeg, as well as parsing all headers in one go, as
required by coda-vpu. The frame header is always parsed, as basically
all decoders are interested in width, height, and number of components.
For convenience, the JPEG chroma subsampling factors are decoded into a
v4l2_jpeg_chroma_subsampling enum.
Only baseline and extended sequential DCT encoded JPEGs with 8-bit or
12-bit precision with up to four components are supported.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The BIT decoders always write 16x16 macroblocks. Align stride and height to
avoid spilling luma data into the top of the chroma planes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
V4L2_PIX_FMT_GREY format is Ycbcr format without
the color data, therefore its pixel_enc should
set to V4L2_PIXEL_ENC_YUV.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move away from the deprecated API.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move away from the deprecated API and make use of the fact that
unregistering devices is NULL- and ERR_PTR-safe.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move away from the deprecated API.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move away from the deprecated API and make use of the fact that
unregistering devices is NULL- and ERR_PTR-safe.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the request API is used, typically an OUTPUT (src) buffer
will be part of a request. A userspace process will be typically
blocked, waiting on the request file descriptor.
Returning the OUTPUT (src) buffer will wake-up such processes,
who will immediately attempt to dequeue the CAPTURE buffer,
only to find it's still unavailable.
Therefore, change v4l2_m2m_buf_done_and_job_finish returning
the CAPTURE (dst) buffer first, to avoid signalling the request
file descriptor prematurely, i.e. before the CAPTURE buffer is done.
When the request API is not used, this change should have
no impact.
Tested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Changing from "depends on" to "select" may cause some
side-effects. This patch is not ready to be merged yet,
as it requires some adjustments.
So, let's revert it.
This reverts commit a3b91d8bd1.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are some uAPI stuff that are driver-specific. Add them
to the main media uAPI body.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Those documents don't really describe the driver API.
Instead, they contain development-specific information.
Yet, as the main index file describes the content of it as:
"how specific kernel subsystems work
from the point of view of a kernel developer"
It seems to be the better fit.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Most of the driver-specific documentation is meant to help
users of the media subsystem.
Move them to the admin-guide.
It should be noticed, however, that several of those files
are outdated and will require further work in order to make
them useful again.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since 2017, there is an space reserved for userspace API,
created by changeset 1d596dee38 ("docs: Create a user-space API guide").
As the media subsystem was one of the first subsystems to use
Sphinx, until this patch, we were keeping things on a separate
place.
Let's just use the new location, as having all uAPI altogether
will likely make things easier for developers.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are two places inside this file that points to the
cx2341x documentation, with was split into two. Looking
at changeset dcc0ef8820
("V4L/DVB (10442): cx18: Fixes for enforcing when Encoder Raw VBI params can be set")
with added those comments, it was originally pointing to:
Documentation/video4linux/cx2341x/fw-encoder-api.txt
Well, the firmware details went to
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While making the menu invisible seemed a good idea, there's
a drawback: when the menu is not visible, it is not parsing
the "default" dependency.
So, instead, let's just avoid the items at the menu to be
prompted, by using the "prompt ... if" construction.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Right now, there are I2C drivers that don't depend on
camera support before and after those.
Move the camera support drivers to the end, and add
a notice at the "endif", in order to make easier to
maintain and to avoid adding extra dependencies at
the other i2c/*/Kconfig files.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After this change, the menu is displayed like above.
1) When filtering is not active:
--- Multimedia support
[ ] Filter devices by their types
[*] Autoselect ancillary drivers (tuners, sensors, i2c, spi, frontends)
Media core support --->
Video4Linux options --->
Media controller options --->
Digital TV options --->
HDMI CEC options --->
Media drivers --->
2) When filtering is active:
--- Multimedia support
[*] Filter devices by their types
[*] Autoselect ancillary drivers (tuners, sensors, i2c, spi, frontends)
Media device types --->
Video4Linux options --->
Media controller options --->
Digital TV options --->
HDMI CEC options --->
Media drivers --->
The per-API menu will only be displayed if the corresponding
core support is enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Advanced and embedded users know what to do, so, by default,
they will likely want to be able to open the entire set of
Kconfig media options.
Normal "poor" users usually needs more help when setting
stuff, so let's open an more simplified version to them by
default.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Let's place the sub-driver-autoselection option just below
the device filtering one, as it also controls a filter menu,
with is not even visible if !EXPERT && !EMBEDDED.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
That should make easier for people setting the media
subsystem config options, as they'll be split by the
type of functionality that will be enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Let's place the main API selections at the media/Kconfig file,
as this way we can better organize things.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This option is part of V4L2 API extra functionality set.
Move it to be at the v4l2-core/Kconfig, where it belongs,
cleaning the main Kconfig file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In order to cleanup the main media Kconfig, move the DVB-core
specific options to dvb-core/Kconfig.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's no need to have the CEC definitions inside the
media Kconfig, as the Kconfig parser doesn't require
symbols to be declared before their usages.
With that, the main Kconfig menu becomes cleaner.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As per a tester feedback, add an option to report when
the drivers are filtered at the Kconfig menu.
Cc: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The per-device option selection is a feature that some
developers love, while others hate...
So, let's make both happy by making it optional.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The media subsystem has hundreds of driver-specific options.
The *_SUPPORT config options work as a sort of filter,
allowing to reduce its complexity for users that won't
want to dig into thousands of options they don't need.
Yet, it the filtering options are becoming large. So, let's
place it on a sub-menu.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The comments before some of the drivers support look
weird, because their Kconfig have their own "comment"
directive inside it. So, rearrange them to make it
look a little nicer for the ones with are not too
familiar with the media system.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are lots of drivers that only work when the media controller
and/or the V4L2 subdev APIs are present.
Right now, someone need to first enable those APIs before
using those drivers.
Well, ideally, drivers, should, instead *optionally*
depend on it, in order for PC camera drivers to be able to use
them, but nowadays most drivers are UVC cameras, with don't
require a sensor driver.
So, be it.
Let's instead make them select the MEDIA_CONTROLLER and the
SUBDEV API, in order to make easier for people to be able
of enabling them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
All modern Linux distributions nowadays use udev or some
alternative (like systemd). So, it makes sense to change
the default to use dynamic minors.
Please notice that this default doesn't enable any code.
It just changes the dvb-core behavior.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Most of media Kconfig/Makefile files already has SPDX,
but there are a few ones still missing. Add it to them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are some long-time mistakes related to build test
drivers, with regards to depends on/select. Also, as we
now want to build any test driver without needing to
enable anything else, change the logic in order to properly
filter them.
Please notice that the PCI skeleton is somewhat an
exception, as it requires to select *both* SAMPLES and
MEDIA_TEST_SUPPORT. I almost changed it to be either one,
but decided to keep it as-is, as this is something that
we don't really need to be included on any distribution.
The only reason for someone to build it is for COMPILE_TEST
purposes.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Right now, if one has an hybrid TV card, it has to select
both analog and digital TV support, as otherwise the needed
core support won't be selected.
Change the logic to auto-select the core support for those
drivers, as this is a way more intuitive.
It should be noticed that, as now both DVB_CORE and VIDEO_DEV
defaults depends on selecting a hybrid cards, we had to remove
the explicit dependencies there, in order to avoid circular
dependencies.
That requires some tricks:
1) the prompt should not be not visible when an hybrid card
is selected, as the user shold not change it.
2) When a media hybrid device is selected, the modular
option for DVB_CORE and VIDEO_DEV will follow the
MEDIA_SUPPORT dependency, as we can't have a core
built with "y" with a driver built as module.
Note: while here, moved two pure V4L2 PCI drivers out of the
"hybrid" part of config and consider pvrusb2 as an hybrid
device.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
both DVB_CORE and VIDEO_DEV already depends on MEDIA_SUPPORT,
as they're below an if block.
So, remove this double dependency.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Neither the PCI skeleton nor the DVB dummy driver are real
drivers. They're there just as an example for a driver
writter.
Distros should not enable those drivers. So, hide them if
MEDIA_TEST_SUPPORT is not selected.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cleanup the ddbridge's dummy driver by removing the parts
that aren't needed by ddbridge, adding it to the building
system and changing the binding at the driver to use the
newer function name.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As the name of this driver is now ddbridge-dummy, do some
renames internally.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As we'll be transforming the dvb-dummy-fe driver soon into a
virtual driver, let's first copy the existing one to ddbridge
as-is, as it is needed there.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This option is used only by av7110 and by an USB driver. As
the av7110 is the first DVB hardware, hardly found those
days, let's opt to place it at usb/Kconfig, as the driver
with needs it might have a longer lifetime.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Showing this comment without showing the Siano mmc option
is very weird! Place the option together, and make it
visible only when showing Siano configuration.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the first test device was added (vivi.c), there were just
one file. I was too lazy on that time to create a separate
directory just for it, so I kept it together with platform.
Now, we have vivid, vicodec, vim2m and vimc. Also, a new
virtual driver has been prepared to support DVB API.
So, it is time to solve this mess, by placing test stuff
on a separate directory.
It should be noticed that we also have some skeleton drivers
(for V4L and for DVB). For now, we'll keep them separate,
as they're not really test drivers, but instead, just
examples. The DVB frontend ones will likely be part of a new DVB
test driver. By that time, it should make sense to move them
here as well.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are more things than just cameras and TV devices on
media. Update the help message accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The V4L2 PCI skeleton is not part of the V4L2 core. Move it
to appear together with the other PCI drivers, at the end,
as this is something that normal users don't even need to
bother.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the platform drivers got added, they were all part of
complex camera support. This is not the case anymore, as we
now have codecs and other stuff there too.
So, fix the dependencies, in order to not require users to
manually select something that it doesn't make sense.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Most systems don't need support for those, while others only
need those, instead of the others.
So, add an option to filter in/out platform drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
At least some of the supported boards by dvb-usb
driver need to load the cypress firmware, so select
it, as otherwise missing dependencies may popup.
Also, as the cypress firmware load routines are needed
only by the dvb-usb, dvb-usb-v2 and go7007 drivers, and
those all (now) select it, there's no need to ask the
user for manually select it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
- Clean up and rework the PM QoS API to simplify the code and
reduce the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370
and similar platforms where the USB plug/unplug events are
handled by the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to
run on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate driver
and update its documentation (Rafael Wysocki, Alex Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file
and use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result (Leonard
Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level
PM QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences
in a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies).
-----BEGIN PGP SIGNATURE-----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=cBQd
-----END PGP SIGNATURE-----
Merge tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These clean up and rework the PM QoS API, address a suspend-to-idle
wakeup regression on some ACPI-based platforms, clean up and extend a
few cpuidle drivers, update multiple cpufreq drivers and cpufreq
documentation, and fix a number of issues in devfreq and several other
things all over.
Specifics:
- Clean up and rework the PM QoS API to simplify the code and reduce
the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370 and
similar platforms where the USB plug/unplug events are handled by
the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to run
on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate
driver and update its documentation (Rafael Wysocki, Alex
Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file and
use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result
(Leonard Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level PM
QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences in
a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies)"
* tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (78 commits)
cpufreq: intel_pstate: Simplify intel_pstate_cpu_init()
tools/power/x86/intel_pstate_tracer: fix a broken y-axis scale
ACPI: PM: s2idle: Refine active GPEs check
ACPICA: Allow acpi_any_gpe_status_set() to skip one GPE
PM: sleep: wakeup: Skip wakeup_source_sysfs_remove() if device is not there
PM / devfreq: Get rid of some doc warnings
PM / devfreq: Fix handling dev_pm_qos_remove_request result
PM / devfreq: Fix a typo in a comment
PM / devfreq: Change to DEVFREQ_GOV_UPDATE_INTERVAL event name
PM / devfreq: Remove unneeded extern keyword
PM / devfreq: Use constant name of userspace governor
ACPI: PM: s2idle: Fix comment in acpi_s2idle_prepare_late()
cpufreq: qcom: Add support for krait based socs
cpufreq: imx6q-cpufreq: Improve the logic of -EPROBE_DEFER handling
cpufreq: Use scnprintf() for avoiding potential buffer overflow
cpuidle: psci: Split psci_dt_cpu_init_idle()
PM / Domains: Allow no domain-idle-states DT property in genpd when parsing
PM / hibernate: Remove unnecessary compat ioctl overrides
PM: hibernate: fix docs for ioctls that return loff_t via pointer
Documentation: intel_pstate: update links for references
...
With the latest cleanup in qcom scm driver the secure monitor
call for setting the remote processor state returns EINVAL when
it is called for the first time and after another scm call
auth_and_reset. The error returned from scm call could be ignored
because the state transition is already done in auth_and_reset.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mt8173 VPU firmware has been moved to a sub-folder of
linux-firmware, so load vpu-fw from the new location first,
if it fails, then from the old one.
Signed-off-by: Rui Wang <gtk_ruiwang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix build fault when CONFIG_HWMON is a module, and CONFIG_VIDEO_I2C
as builtin. This is due to 'imply hwmon' in the respective Kconfig.
Issue build log:
ld: drivers/media/i2c/video-i2c.o: in function `amg88xx_hwmon_init':
video-i2c.c:(.text+0x2e1): undefined reference to `devm_hwmon_device_register_with_info
Cc: rdunlap@infradead.org
Fixes: acbea67989 (media: video-i2c: add hwmon support for amg88xx)
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The initial physical address was one too low for the outputs.
E.g. if 1.0.0.0 was expected, then it was set to 0.0.0.0, and
2.0.0.0 became 1.0.0.0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Johan Korsnes <johan.korsnes@gmail.com>
Fixes: 4ee895e71a ("media: vivid: reorder CEC allocation and control set-up")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This function is no longer used by other drivers, so it can be
made static.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This argument refers to a stable name for an HDMI port, mostly i915
(ACPI) specific. Since we'll be introducing a more generic 'name' argument
as well later, rename this now to avoid confusion.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch makes use of to_vpfe() to get a pointer to vpfe_device
Signed-off-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The new format is called V4L2_PIX_FMT_Y14. Like V4L2_PIX_FMT_Y10 and
V4L2_PIX_FMT_Y12 it is stored in two bytes per pixel but has only two
unused bits at the top.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Check the return value of of_clk_get and print an error
message if not EPROBE_DEFER.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Change stm32-cec driver to not print an error message when the
device probe operation is deferred.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Change stm32-cec driver to defer probe when auxiliary clock
"hdmi-cec" is registered in the system not has not been probed yet.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make sure to check that we have two alternate settings and at least one
endpoint before accessing the second altsetting structure and
dereferencing the endpoint arrays.
This specifically avoids dereferencing NULL-pointers or corrupting
memory when a device does not have the expected descriptors.
Note that the sanity check in cit_get_packet_size() is not redundant as
the driver is mixing looking up altsettings by index and by number,
which may not coincide.
Fixes: 659fefa0eb ("V4L/DVB: gspca_xirlink_cit: Add support for camera with a bcd version of 0.01")
Fixes: 59f8b0bf3c ("V4L/DVB: gspca_xirlink_cit: support bandwidth changing for devices with 1 alt setting")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make sure to check that we have two alternate settings and at least one
endpoint before accessing the second altsetting structure and
dereferencing the endpoint arrays.
This specifically avoids dereferencing NULL-pointers or corrupting
memory when a device does not have the expected descriptors.
Note that the sanity checks in stv06xx_start() and pb0100_start() are
not redundant as the driver is mixing looking up altsettings by index
and by number, which may not coincide.
Fixes: 8668d504d7 ("V4L/DVB (12082): gspca_stv06xx: Add support for st6422 bridge and sensor")
Fixes: c0b33bdc5b ("[media] gspca-stv06xx: support bandwidth changing")
Cc: stable <stable@vger.kernel.org> # 2.6.31
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make sure to check that we have at least one endpoint before accessing
the endpoint array to avoid dereferencing a NULL-pointer on stream
start.
Note that these sanity checks are not redundant as the driver is mixing
looking up altsettings by index and by number, which need not coincide.
Fixes: 1876bb923c ("V4L/DVB (12079): gspca_ov519: add support for the ov511 bridge")
Fixes: b282d87332 ("V4L/DVB (12080): gspca_ov519: Fix ov518+ with OV7620AE (Trust spacecam 320)")
Cc: stable <stable@vger.kernel.org> # 2.6.31
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As of `s5c73m3.h` the auto focus cluster in `s5c73m3_ctrls` has 5 and not 6
controls.
Signed-off-by: Sebastian Gross <sebastian.gross@emlix.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This dprintk is supposed to be informational, not an error. Set it to
the same level as the other messages related to memory allocations so
the kernel log does not get filled by messages during normal operation.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pad is now checked by v4l2_subdev_call_wappers
call_g_frame_interval-> check_frame_interval-> check_pad
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
From the measured hardware signal, OV5695 reset pin goes high for a
short period of time during boot-up. From the sensor specification, the
reset pin is active low and the DT binding defines the pin as active
low, which means that the values set by the driver are inverted and thus
the value requested in probe ends up high.
Fix it by changing probe to request the reset GPIO initialized to high,
which makes the initial state of the physical signal low.
In addition, DOVDD rising must occur before DVDD rising from spec., but
regulator_bulk_enable() API enables all the regulators asynchronously.
Use an explicit loops of regulator_enable() instead.
For power off sequence, it is required that DVDD falls first. Given the
bulk API does not give any guarantee about the order of regulators,
change the driver to use regulator_disable() instead.
The sensor also requires a delay between reset high and first I2C
transaction, which was assumed to be 8192 XVCLK cycles, but 1ms is
recommended by the vendor. Fix this as well.
Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IMX219 sensor is capable for RAW8/RAW10 modes. This commit adds support
for RAW8 bayer format.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When supporting Rpi Camera v2 Module on the RZ/G2E, found the driver had
some issues with rcar mipi-csi driver. The sensor never entered into LP-11
state.
The powerup sequence in the datasheet[1] shows the sensor entering into
LP-11 in streaming mode, so to fix this issue transitions are performed
from "streaming -> standby" in the probe() after power up.
With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.
[1] https://publiclab.org/system/images/photos/000/023/294/original/
RASPBERRY_PI_CAMERA_V2_DATASHEET_IMX219PQH5_7.0.0_Datasheet_XXX.PDF
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While upgrading from 5.5.2 -> 5.5.6 I was surprised by:
ld: drivers/media/i2c/tvp5150.o: in function `tvp5150_probe':
tvp5150.c:(.text+0x11ac): undefined reference to
`__devm_regmap_init_i2c'
make: *** [Makefile:1078: vmlinux] Error 1
The fix was quick enough, make VIDEO_TVP5150 select REGMAP_I2C
And a quick grep showed that it was needed by more targets.
Signed-off-by: Ian Kumlien <ian.kumlien@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The debug output for tvp5150_selmux() isn't really intuitive. Register
values are printed decimal formatted and the input/output driver states
are printed as enum. Even more the "normal" output enum mapps to zero so
a active output will printing output=0 and a inactive output=1.
Change this by brinting the register values hex formatted and the states
as more readable string.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The tvp5150 accepts NTSC(M,J,4.43), PAL (B,D,G,H,I,M,N) and SECAM video
data and is able to auto-detect the input signal. The auto-detection
does not work if the connector does not receive an input signal and the
tvp5150 might not be configured correctly. This misconfiguration leads
into wrong decoded video streams if the tvp5150 gets powered on before
the video signal is present.
Limit the supported sdtv standards according to the actual selected
connector to avoid a misconfiguration.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Bring the device into a working state upon a open/close call. Currently
this involves only the interrupt enable/disable process but can be
extended in the future.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the driver notifies internal subdevs if the signal is locked
or not. This information is also useful for userpace applications e.g. to
switch to another input device upon a signal lost event.
This commit adds the support for the userspace to subscribe to the
V4L2_EVENT_SOURCE_CHANGE and V4L2_EVENT_CTRL events.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As documented in [1] the runtime-pm ops are used to set the device into
a fully 'workable' state. Therefore it can be used to enable or disable
the irqs.
[1] https://www.kernel.org/doc/html/latest/power/runtime_pm.html
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are several debug prints in the tvp5150_parse_dt() function, which
do not print the prefix, because the v4l2_subdev is not initialized, yet.
Initialize the v4l2_subdev before parsing the device tree to fix the
debug messages.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since commit 10d5509c8d ("[media] v4l2: remove g/s_crop from video ops")
the 'which' field for set/get_selection must be FORMAT_ACTIVE. There is
no way to try different selections. The patch adds a helper function to
select the correct selection memory space (sub-device file handle or
driver state) which will be set/returned.
The selection rectangle is updated if the format is FORMAT_ACTIVE and
the rectangle position and/or size differs from the current set
rectangle.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently a local copy of sel->r is made and adapted to the hardware
constraints. After the adaption the value is applied to the hardware but
the driver forgot to reflect the adapted value to the user space.
Drop the local copy and work directly on the requested rectangle
instead to fix this.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch adds the of_graph support to describe the tvp input connections.
Physical the TVP5150 has three ports: AIP1A, AIP1B and YOUT. As result
of discussion [1],[2] the device-tree maps these ports 1:1. Look at the
Documentation for more information. Since the TVP5150 is a converter/bridge
the device-tree must contain at least 1-input and 1-output port. The
mc-connectors and mc-links are only created if the device-tree contains the
corresponding connector nodes. If more than one connector is available the
media_entity_operations.link_setup() callback ensures that only one
connector is active.
[1] https://www.spinics.net/lists/linux-media/msg138545.html
[2] https://www.spinics.net/lists/linux-media/msg138546.html
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit f7b4b54e63 ("[media] tvp5150: add HW input connectors support")
added input signals support for the tvp5150, but the approach was found
to be incorrect so the corresponding DT binding commit 82c2ffeb21
("[media] tvp5150: document input connectors DT bindings") was reverted.
This left the driver with an undocumented (and wrong) DT parsing logic,
so lets get rid of this code as well until the input connectors support
is implemented properly.
It's a partial revert due other patches added on top of mentioned commit
not allowing the commit to be reverted cleanly anymore. But all the code
related to the DT parsing logic and input entities creation are removed.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[m.felsch@pengutronix.de: rm TVP5150_INPUT_NUM define]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The patch adds the initial connector parsing code, so we can move from a
driver specific parsing code to a generic one. Currently only the
generic fields and the analog-connector specific fields are parsed. Parsing
the other connector specific fields can be added by a simple callbacks.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
[hverkuil-cisco@xs4all.nl: replace ; with break; in a empty case]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
A link is between two endpoints not between two ports to be more
precise. Add the local_id/remote_id field which stores the endpoint
reg/port property to the link. Now the link holds all necessary
information about a link.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This helper was introduced before those helpers where awailable. Convert
it to cleanup the code and improbe readability.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the driver differentiate the port number property handling for
ACPI and DT. This is wrong as because ACPI should use the "reg" val too
[1].
[1] https://patchwork.kernel.org/patch/11421985/
Fixes: ca50c197bd ("[media] v4l: fwnode: Support generic fwnode for parsing standardised properties")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling ccdc_data_size_max_bit() to validate data_sz in
vpfe_ccdc_validate_param(), it's treated as an enumeration ranging from
0 to 7 while essentially it's an 32 bit unsigned integer directly from
user space. This can make the return value of ccdc_data_size_max_bit()
underflow and bypass the following check.
To fix this, an additional check is added to the following if clause to
keep this enumaration variable in range. And if its value is not legal,
return -EINVAL properly.
Signed-off-by: Changming Liu <charley.ashbringer@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After the switch to use v4l2_async_notifier_add_subdev() and
v4l2_async_notifier_cleanup(), unloading the ti_cal module would cause a
kernel oops.
This was root cause to the fact that v4l2_async_notifier_cleanup() tries
to kfree the asd pointer passed into v4l2_async_notifier_add_subdev().
In our case the asd reference was from a statically allocated struct.
So in effect v4l2_async_notifier_cleanup() was trying to free a pointer
that was not kalloc.
So here we switch to using a kzalloc struct instead of a static one.
To achieve this we re-order some of the calls to prevent asd allocation
from leaking.
Fixes: d079f94c90 ("media: platform: Switch to v4l2_async_notifier_add_subdev")
Cc: stable@vger.kernel.org
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Previously, vpu->recv_buf and send_buf are forced cast from
void __iomem *tcm. vpu->recv_buf->share_buf is passed to
vpu_ipi_desc.handler(). It's not able to do unaligned access. Otherwise
kernel would crash due to unable to handle kernel paging request.
struct vpu_run {
u32 signaled;
char fw_ver[VPU_FW_VER_LEN];
unsigned int dec_capability;
unsigned int enc_capability;
wait_queue_head_t wq;
};
fw_ver starts at 4 byte boundary. If system enables
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS, strscpy() will do
read_word_at_a_time(), which tries to read 8-byte: *(unsigned long *)addr
vpu_init_ipi_handler() calls strscpy(), which would lead to crash.
vpu_init_ipi_handler() and several other handlers (eg.
vpu_dec_ipi_handler) only do read access to this data, so they can be
const, and we can use memcpy_fromio() to copy the buf to another non iomem
buffer then pass to handler.
Fixes: 85709cbf15 ("media: replace strncpy() by strscpy()")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add encoder control for enabling/disabling frame rate control via
V4L2_CID_MPEG_VIDEO_FRAME_RC_ENABLE. It is enabled by default.
Signed-off-by: Jeffrey Kardatzke <jkardatzke@google.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This fixes the following smatch warning in the error path:
drivers/media/platform/qcom/venus/vdec.c:968 vdec_start_streaming()
warn: inconsistent returns 'mutex:&inst->lock'.
Locked on: line 952
Unlocked on: line 963
line 968
by goto mutex unlock.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The variable gate is being initialized and also checked and re-assigned
with values that are never read as it is being re-assigned later in a
for-loop with a new value. The assignments are redundant and can be
removed.
Addresses Coverity ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The shifting of buf[3] by 24 bits to the left will be promoted to
a 32 bit signed int and then sign-extended to an unsigned long. In
the unlikely event that the the top bit of buf[3] is set then all
then all the upper bits end up as also being set because of
the sign-extension and this affect the ev->post_bit_error sum.
Fix this by using the temporary u32 variable bit_error to avoid
the sign-extension promotion. This also removes the need to do the
computation twice.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 267897a470 ("[media] tda10071: implement DVBv5 statistics")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is required to support the Terratec S2 USB Box Revision 4, which
reused usb vid:pid, but has a different demodulator (m88ds3103b) at
i2c address 0x6a.
[fixed checkpatch issues]
Signed-off-by: Michael Bunk <micha@freedict.org>
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hauppauge 461e rev2 is a DVB-S/S2 usb device containing:
- m88ds3103b demod
- ts2022 tuner
- A8293 SEC
Device is the same as Hauppauge 461e,
except it contains updated m88ds3103b demod.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ds3103b demodulator identifies as an m88rs600, but requires different
clock settings and firmware, along with differences in register settings.
Changes were reverse engineered using an instrumented downstream GPLv2
driver to compare i2c traffic and clocking. The mclk functions are from
the downstream GPLv2 driver.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are many protocols that encode more than 32 bit. We want 64 bit
support so that BPF IR decoders can decode more than 32 bit. None of
the existing kernel IR decoders/encoders support 64 bit, for now.
The MSC_SCAN event can only contain 32 bit scancodes, so we only generate
MSC_SCAN events if the scancode fits into 32 bits. The full 64 bit
scancode can be read from the lirc chardev.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the previously introduced v4l2-mem2mem core APIs to handle the drainig,
stopped and next-buf-is-last states.
With these changes, the v4l2-compliance still passes with the following
commands :
>>>><><><><><><><><><><><><><><><><>< 15.53 fps
15.53 fps
><><><><><><><><><><><><>< 13.99 fps
13.99 fps
><><><><><><><><><><><>< 13.52 fps
13.52 fps
><><><><><><><><><><><><>< 13.41 fps
13.41 fps
><><><><><><><><><><><><>< 13.21 fps
13.21 fps
><><><><><><><><><><><>< 13.09 fps
13.09 fps
><><><><><><><
STOP ENCODER
<<<
EOS EVENT
v4l2-compliance SHA: 7ead0e1856b89f2e19369af452bb03fd0cd16793, 64 bits
[...]
Total for vicodec device /dev/video0: 50, Succeeded: 50, Failed: 0, Warnings: 0
The full output is available at [1]
v4l2-compliance SHA: 7ead0e1856b89f2e19369af452bb03fd0cd16793, 64 bits
[...]
Total for vicodec device /dev/video1: 50, Succeeded: 50, Failed: 0, Warnings: 0
The full output is available at [2]
No functional changes should be noticed.
[1] https://termbin.com/25nn
[2] https://termbin.com/dza4
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Suggested-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since the draining and stop phase of the HW decoder mem2mem bahaviour is
now clearly defined, we can move handling of the following states to the
common v4l2-mem2mem core code:
- draining
- stopped
- next-buf-is-last
By introducing the following v4l2-mem2mem APIs:
- v4l2_m2m_encoder_cmd/v4l2_m2m_ioctl_encoder_cmd to handle start/stop command
- v4l2_m2m_decoder_cmd/v4l2_m2m_ioctl_decoder_cmd to handle start/stop command
- v4l2_m2m_update_start_streaming_state to update state on start of streaming
of the de/encoder queue
- v4l2_m2m_update_stop_streaming_state to update state on stop of streaming
of the de/encoder queue
- v4l2_m2m_last_buffer_done to make the current dest buffer as the last one
And inline helpers:
- v4l2_m2m_mark_stopped to mark the de/encoding process as stopped
- v4l2_m2m_clear_state to clear the de/encoding state
- v4l2_m2m_dst_buf_is_last to detect the current dequeued dst_buf is the last
- v4l2_m2m_has_stopped to detect the de/encoding stopped state
- v4l2_m2m_is_last_draining_src_buf to detect the current source buffer should
be the last processing before stopping the de/encoding process
The special next-buf-is-last when min_buffers != 1 case is also handled
in v4l2_m2m_qbuf() by reusing the other introduced APIs.
This state management has been stolen from the vicodec implementation,
and is no-op for drivers not calling the v4l2_m2m_encoder_cmd or
v4l2_m2m_decoder_cmd and v4l2_m2m_update_start/stop_streaming_state.
The vicodec will be the first one to be converted as an example.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the request is completed, all controls are copied to the request object.
However, when VIDIOC_G_EXT_CTRLS attempts to read control values from the
request it will read the current value instead for any control reference that
has a NULL ref->req pointer. But that's wrong: after completing the request
*all* controls should have a non-NULL ref->req pointer since they are after
all copied to the request.
So set ref->req if it wasn't set already.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
disable_irqs() was mistakenly disabling all interrupts when called.
This cause all port stream to stop even if only stopping one of them.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The entity variable was being initialized in the wrong place, before the
parameters have been checked.
To solve this, completely removed the entity variable and replaced it
with the initialization value : &sd->entity.
This will avoid dereferencing 'sd' pointer before it's being checked if
it's NULL.
Fixes: 61f5db549d ("[media] v4l: Make v4l2_subdev inherit from media_entity")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
sd->devnode is released after calling
v4l2_subdev_release. Therefore it should be set
to NULL so that the subdev won't hold a pointer
to a released object. This fixes a reference
after free bug in function
v4l2_device_unregister_subdev
Fixes: 0e43734d4c ("media: v4l2-subdev: add release() internal op")
Cc: stable@vger.kernel.org
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In future patch, the release of the device will move
to the release callback of v4l2_device. Therefore the
device will be released only when the last fh will be
closed. Dynamic allocation will then be needed since
when the device is unbounded and then bounded again,
it might be that the probe callback will run before
the release of the last device is finished. In that
case both operations will run on the same memory
concurrently and cause memory corruption.
This patch also removes the pdev field of
vimc_device since it is not needed anymore.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
replace 'vimc->pdev.dev' with 'vimc->mdev.dev'
in debug prints and in assignment to
vimc_ent_device.dev. This helps to unify the debug
statements. This will also eliminate the need to use
the pdev field in vimc_device in future patch.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the dma channel request error code is EPROBE_DEFER there is no need to
print error message.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Video engine in AST2600 has the exactly same register set with
AST2500 except VR084 register which provides more precise JPEG
size read back. This commit adds support for the difference and
adds 'aspeed,ast2600-video-engine' compatible OF string.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove a spurious 'b' in the "contiguous chunk is too small %lu/%lu b"
message.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
VP9 bitstream specification indicate segment data should reset to
default when meet key frames, intra only frames or enable error
resilience mode. So memset segmentation map buffer before every
decode process is not appropriate.
Reset segment data only when needed, then start decoder hardware
Signed-off-by: Rui Wang <gtk_ruiwang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Josef reported that his old-and-good Plextor ConvertX M402U video
converter spews lots of WARNINGs on the recent kernels, and it turned
out that the device uses a bulk endpoint for interrupt handling just
like 2250 board.
For fixing it, generalize the check with the proper verification of
the endpoint instead of hard-coded board type check.
Fixes: 7e5219d18e ("[media] go7007: Fix 2250 urb type")
Reported-and-tested-by: Josef Möllers <josef.moellers@suse.com>
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1162583
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206427
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Allwinner A83T contains rotation core which can rotate and flip images.
Add a driver for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[hverkuil-cisco@xs4all.nl: MAINTAINERS paths were out of date, fix that]
[hverkuil-cisco@xs4all.nl: VFL_TYPE_GRABBER -> _VIDEO]
[hverkuil-cisco@xs4all.nl: Fix module build]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently, v4l2_pipeline_pm_use() prototype is:
int v4l2_pipeline_pm_use(struct media_entity *entity, int use)
Where the 'use' argument shall only be set to '1' for enable/power-on,
or to '0' for disable/power-off. The integer return is specified
as only meaningful when 'use' is set to '1'.
Let's enforce this semantic by splitting the function in two:
v4l2_pipeline_pm_get and v4l2_pipeline_pm_put. This is done
for several reasons.
It makes the API easier to use (or harder to misuse).
It removes the constraint on the values the 'use' argument
shall take. Also, it removes the need to constraint
the return value, by making v4l2_pipeline_pm_put void return.
And last, it's more consistent with other kernel APIs, such
as the runtime pm APIs, which makes the code more symmetric.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver is deprecated and scheduled for removal by the end
of 2020. The reason is that this driver is for old and obsolete
hardware, and it produces a continuous stream of syzbot errors due
to poor code.
In order to prevent removal the following actions would have to
be taken:
- clean up the code
- convert to the vb2 framework
- fix the disconnect and free-on-last-user handling (i.e., add
a release callback for struct v4l2_device and rework the code
to use that correctly).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Slave demod needs some time to wake up otherwise it may not respond to the
following probe commands. This problem manifested randomly on my Astrometa
DVB-T2 dongle.
Signed-off-by: Mario Hros <git@reversity.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is a spelling mistake in a dev_dbg message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
include/media/i2c/smiapp.h was meant to serve systems where the sensor is
enumerated through platform data. That's no longer necessary, hopefully
not even in out-of-tree use cases. Move the definitions to the appropriate
headers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Combine the two trivial functions reading limits into one. Also rename
smiapp_get_all_limits() as smiapp_read_all_smia_limits().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of direct array access, turn accessing limit information into a
function. Going forward, more elaborate CCS limits will replace most SMIA
limits, and conversion will be less complicated this way.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use get_unaligned_be* and put_unaligned_be* functions to convert register
values to CPU endianness. Consequently, two instances of BUG() are
removed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the only8 boolean to determine whether 8-bit access is required for
reading.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit ... prevented restarting CCDC through its interrupt handler when
it's about to be disabled. It missed to address the case when CCDC might
be enabled due to queueing a buffer. Do that now.
Fixes: dd12ed17ce ("omap3isp: Don't restart CCDC if we're about to stop")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Adds a driver for the 8MPix Sony IMX219 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
8MPix @ 15fps, 1080P @ 30fps (cropped FOV), and 1640x1232 (2x2 binned)
@ 30fps are currently supported.
[Sakari Ailus: make imx219_check_hwcfg static]
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In order to use dynamic video codec assignment add a new sdm845-v2
DT compatible and new venus_resource structure to cover the binding
where all pmdomains and clocks are under the venus_core control.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Handle 10bit video streams in the decoder by using dithering, i.e
the decoder output buffers will be in 8bit format.
The runtime handling is implemented by sending v4l2 event to
userspace application, then the application should stop the
streaming on capture queue and initiate format negotiation, and
start streaming again.
Signed-off-by: Aniket Masule <amasule@codeaurora.org>
Co-developed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Presently the core (vcodec pipelines) assignment is static. Here we
introduce dynamic load balancing across the cores depending on the
current session load. The load on earch core is calculated and core
with minimum load is assigned to given instance. This will be
applicable on Venus v4 with more than one vcodec cores.
Signed-off-by: Aniket Masule <amasule@codeaurora.org>
Co-developed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Redesign core (vcodec) clock control to give the venus core more
freedom to control them in order to make possible to use core
selection feature on Venus IP v4.
Move all clock and pmdomain functions in separate file and abstract
power control with common operations per Venus IP version.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Those two properties are not implemented for Venus v4 (sdm845),
thus don't set them to firmware.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace explicit use of members of struct resource by %pR to print
the resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some older MSM8916 Venus firmware versions also seem to indicate
support for encoding HEVC, even though they really can't.
This will lead to errors later because hfi_session_init() fails
in this case.
HEVC is already ignored for "dec_codecs", so add the same for
"enc_codecs" to make these old firmware versions work correctly.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use WARN_ON instead of BUG_ON.
Add two new WARN_ONs to verify that the source pad is really a source
and that the sink pad is really a sink.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: use ! instead of == NULL for source and sink]
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ignore errors returned from kthread_stop since the
vimc subdevices should still be notified that
streaming stopped so they can release the memory for
the streaming, and also kthread should be set to NULL.
kthread_stop can return -EINTR in case the thread
did not yet run. This can happen if userspace calls
streamon and streamoff right after.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's a mistakenly written self assignment in
`static int vpfe_enum_fmt_vid_cap(..)`.
Fixed it according to Prabhakar Lad's feedback.
Signed-off-by: Cengiz Can <cengiz@kernel.wtf>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'GRABBER' is a weird name, all other types map to the /dev
device names. Rename to 'VIDEO' to be consistent with the
other types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'GRABBER' is a weird name, all other types map to the /dev
device names. Rename to 'VIDEO' to be consistent with the
other types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'GRABBER' is a weird name, all other types map to the /dev
device names. Rename to 'VIDEO' to be consistent with the
other types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'GRABBER' is a weird name, all other types map to the /dev
device names. Rename to 'VIDEO' to be consistent with the
other types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'GRABBER' is a weird name, all other types map to the /dev
device names. Rename to 'VIDEO' to be consistent with the
other types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We currently have the following devnode types:
enum vfl_devnode_type {
VFL_TYPE_GRABBER = 0,
VFL_TYPE_VBI,
VFL_TYPE_RADIO,
VFL_TYPE_SUBDEV,
VFL_TYPE_SDR,
VFL_TYPE_TOUCH,
VFL_TYPE_MAX /* Shall be the last one */
};
They all make sense, except for the first: GRABBER really refers to /dev/videoX
devices, which can be capture, output or m2m, so 'grabber' doesn't even refer to
their function anymore.
Let's call a spade a spade and rename this to VFL_TYPE_VIDEO.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver forgets to disable and unprepare clock when remove.
Add a call to clk_disable_unprepare() to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is an NEC remote control device shipped with the Videostrong KII Pro
tv box as well as other devices from videostrong.
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The variable rc is being initialized with a value that is never
read and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid submitting an URB to an invalid endpoint.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: c4018fa2e4 ("[media] dib0700: fix RC support on Hauppauge Nova-TD")
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
commit 1b976fc6d6 ("media: b2c2-flexcop-usb: add sanity checking") added
an endpoint sanity check to address a NULL-pointer dereference on probe.
Unfortunately the check was done on the current altsetting which was later
changed.
Fix this by moving the sanity check to after the altsetting is changed.
Fixes: 1b976fc6d6 ("media: b2c2-flexcop-usb: add sanity checking")
Cc: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The hardware does not support capturing the field types
V4L2_FIELD_SEQ_TB and V4L2_FIELD_SEQ_BT. To capture in these formats the
driver needs to adjust the offset of the capture buffer and capture
twice to each vb2 buffer.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To support SEQ_TB/BT not all buffers given to the hardware will be
equal, the driver needs to keep track of different buffer types. Move
the tracking of buffers given to hardware into a struct so additional
tracking fields can be associated with each buffer.
[hverkuil: fix small checkpatch warning]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In case kthread_run fails, the vimc subdevices
should be notified that streaming stopped so they can
release the memory for the streaming. Also, kthread should be
set to NULL.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a init_cfg pad operation so that configurations allocated with
v4l2_subdev_alloc_pad_config() are initialized.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging on
various user requests due to a malfunctioning (or malicious) device
until the device is physically disconnected.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: f3d27f34fd ("[media] usbtv: Add driver for Fushicai USBTV007 video frame grabber")
Fixes: c53a846c48 ("[media] usbtv: add video controls")
Cc: stable <stable@vger.kernel.org> # 3.11
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This exposes the white balance configuration of the ISC as v4l2 controls
into userspace.
There are 8 controls available:
4 gain controls, sliders, for each of the BAYER components: R, B, GR, GB.
These gains are multipliers for each component, in format unsigned 0:4:9
with a default value of 512 (1.0 multiplier).
4 offset controls, sliders, for each of the BAYER components: R, B, GR, GB.
These offsets are added/substracted from each component, in format signed
1:12:0 with a default value of 0 (+/- 0)
To expose this to userspace, added 8 custom controls, in an auto cluster.
To summarize the functionality:
The auto cluster switch is the auto white balance control, and it works
like this:
AWB == 1: autowhitebalance is on, the do_white_balance button is inactive,
the gains/offsets are inactive, but volatile and readable.
Thus, the results of the whitebalance algorithm are available to userspace
to read at any time.
AWB == 0: autowhitebalance is off, cluster is in manual mode, user can
configure the gain/offsets directly. More than that, if the
do_white_balance button is pressed, the driver will perform
one-time-adjustment, (preferably with color checker card) and the userspace
can read again the new values.
With this feature, the userspace can save the coefficients and reinstall
them for example after reboot or reprobing the driver.
[hverkuil: fix checkpatch warning]
[hverkuil: minor spacing adjustments in the functionality description]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the preferred form for GPL2+, and add IBM and Intel as the authors.
The driver was initially upstreamed by Eddie from IBM, and has had major
contributions from Jae at Intel.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The aspeed video IP has some differences between SoC families. Currently
the driver decides which registers to use at compile time, which means
a single kernel can not be used between platforms.
Switch to using runtime configuration of the registers that vary between
SoC families. This is in preparation for upcoming ast2600 support.
[hverkuil: replace ;; by ;]
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the recently introduced function devm_platform_ioremap_resource to
save a few lines of code. This makes the driver match common platform
device probe patterns.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Tomi Valkeinen
Mansur Alisha Shaik
Gustavo A. R. Silva
Stanimir Varbanov
Mauro Carvalho Chehab
Ezequiel Garcia
Dafna Hirschfeld
Adrian Ratiu
Philipp Zabel
Wolfram Sang
Linus Torvalds
Rafael J. Wysocki
Rui Wang
Matt Ranostay
Hans Verkuil
Takashi Iwai
Lad Prabhakar
Daniel Glöckner
Sakari Ailus
Matthias Brugger
Etienne Carriere
Johan Hovold
Sebastian Gross
Alexandre Courbot
Ricardo Ribalda Delgado
Dongchun Zhu
Lad Prabhakar
Ian Kumlien
Marco Felsch
Michael Tretter
Javier Martinez Canillas
Changming Liu
Benoit Parrot
Hsin-Yi Wang
Jeffrey Kardatzke
Colin Ian King
Brad Love
Sean Young
Neil Armstrong
Sergiu Cuciurean
Eugen Hristev
Peter Ujfalusi
Jae Hyun Yoo
Jernej Skrabec
Mario Hros
Kuninori Morimoto
Dave Stevenson
Shawn Tu
Dikshita Agarwal
Aniket Masule
Andy Shevchenko
Stephan Gerhold
Cengiz Can
YueHaibing
Chuhong Yuan
Mohammad Rasim
Niklas Söderlund
Joel Stanley