The DLCI driver (dlci.c) implements the Frame Relay protocol. However,
we already have another newer and better implementation of Frame Relay
provided by the HDLC_FR driver (hdlc_fr.c).
The DLCI driver's implementation of Frame Relay is used by only one
hardware driver in the kernel - the SDLA driver (sdla.c).
The SDLA driver provides Frame Relay support for the Sangoma S50x devices.
However, the vendor provides their own driver (along with their own
multi-WAN-protocol implementations including Frame Relay), called WANPIPE.
I believe most users of the hardware would use the vendor-provided WANPIPE
driver instead.
(The WANPIPE driver was even once in the kernel, but was deleted in
commit 8db60bcf30 ("[WAN]: Remove broken and unmaintained Sangoma
drivers.") because the vendor no longer updated the in-kernel WANPIPE
driver.)
Cc: Mike McLagan <mike.mclagan@linux.org>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201114150921.685594-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If memory allocation for 'kbuf' succeed, cosa_write() doesn't have a
corresponding kfree() in exception handling. Thus add kfree() for this
function implementation.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Acked-by: Jan "Yenya" Kasprzak <kas@fi.muni.cz>
Link: https://lore.kernel.org/r/20201110144614.43194-1-wanghai38@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver transports LAPB (X.25 link layer) frames over TTY links.
I can safely say that this driver has no actual user because it was
not working at all until:
commit 8fdcabeac3 ("drivers/net/wan/x25_asy: Fix to make it work")
The code in its current state still has problems:
1.
The uses of "struct x25_asy" in x25_asy_unesc (when receiving) and in
x25_asy_write_wakeup (when sending) are not protected by locks against
x25_asy_change_mtu's changing of the transmitting/receiving buffers.
Also, all "netif_running" checks in this driver are not protected by
locks against the ndo_stop function.
2.
The driver stops all TTY read/write when the netif is down.
I think this is not right because this may cause the last outgoing frame
before the netif goes down to be incompletely transmitted, and the first
incoming frame after the netif goes up to be incompletely received.
And there may also be other problems.
I was planning to fix these problems but after recent discussions about
deleting other old networking code, I think we may just delete this
driver, too.
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20201105073434.429307-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change the fr_rx function to make this driver support any Ethertype
when receiving skbs on normal (non-Ethernet-emulating) PVC devices.
(This driver is already able to handle any Ethertype when sending.)
Originally in the fr_rx function, the code that parses the long (10-byte)
header only recognizes a few Ethertype values and drops frames with other
Ethertype values. This patch replaces this code to make fr_rx support
any Ethertype. This patch also creates a new function fr_snap_parse as
part of the new code.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
1.
Change the skb->len check from "<= 4" to "< 4".
At first we only need to ensure a 4-byte header is present. We indeed
normally need the 5th byte, too, but it'd be more logical and cleaner
to check its existence when we actually need it.
2.
Add an fh->ea2 check to the initial checks in fr_rx. fh->ea2 == 1 means
the second address byte is the final address byte. We only support the
case where the address length is 2 bytes.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When an skb is received on a normal (non-Ethernet-emulating) PVC device,
call skb_reset_mac_header before we pass it to upper layers.
This is because normal PVC devices don't have header_ops, so any header we
have would not be visible to upper layer code when sending, so the header
shouldn't be visible to upper layer code when receiving, either.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The eth_type_trans function is called when we receive frames carrying
Ethernet frames. This function expects a non-NULL pointer as an argument,
and assigns it directly to skb->dev.
However, the code handling other types of frames first assigns the pointer
to "dev", and then at the end checks whether the value is NULL, and if it
is not NULL, assigns it to skb->dev.
The two flows are different. Mixing them in this function makes the code
messy. It's better that we convert the second flow to align with how
eth_type_trans does things.
So this patch changes the code to: first make sure the pointer is not
NULL, then assign it directly to skb->dev. "dev" is no longer needed until
the end where we use it to update stats.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the fr_rx function drops a received frame (because the protocol type
is not supported, or because the PVC virtual device that corresponds to
the DLCI number and the protocol type doesn't exist), the function frees
the skb and returns.
The code for freeing the skb and returning is repeated several times, this
patch uses "goto rx_drop" to replace them so that the code looks cleaner.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/wan/lmc/lmc_main.c: In function ‘lmc_ioctl’:
drivers/net/wan/lmc/lmc_main.c:356:25: warning: variable ‘mii’ set but not used [-Wunused-but-set-variable]
356 | u16 mii;
| ^~~
drivers/net/wan/lmc/lmc_main.c:427:25: warning: variable ‘mii’ set but not used [-Wunused-but-set-variable]
427 | u16 mii;
| ^~~
drivers/net/wan/lmc/lmc_main.c: In function ‘lmc_interrupt’:
drivers/net/wan/lmc/lmc_main.c:1188:9: warning: variable ‘firstcsr’ set but not used [-Wunused-but-set-variable]
1188 | u32 firstcsr;
This file has funky indentation, and makes little use of tabs. Keep
with this style in the patch, but that makes checkpatch unhappy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201031181417.1081511-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver calls ether_setup to set up the network device.
The ether_setup function would add the IFF_TX_SKB_SHARING flag to the
device. This flag indicates that it is safe to transmit shared skbs to
the device.
However, this is not true. This driver may pad the frame (in eth_tx)
before transmission, so the skb may be modified.
Fixes: 550fd08c2c ("net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared")
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201020063420.187497-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hdlc_rcv function is used as hdlc_packet_type.func to process any
skb received in the kernel with skb->protocol == htons(ETH_P_HDLC).
The purpose of this function is to provide second-stage processing for
skbs not assigned a "real" L3 skb->protocol value in the first stage.
This function assumes the device from which the skb is received is an
HDLC device (a device created by this module). It assumes that
netdev_priv(dev) returns a pointer to "struct hdlc_device".
However, it is possible that some driver in the kernel (not necessarily
in our control) submits a received skb with skb->protocol ==
htons(ETH_P_HDLC), from a non-HDLC device. In this case, the skb would
still be received by hdlc_rcv. This will cause problems.
hdlc_rcv should be able to recognize and drop invalid skbs. It should
first make sure "dev" is actually an HDLC device, before starting its
processing. This patch adds this check to hdlc_rcv.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Link: https://lore.kernel.org/r/20201020013152.89259-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the skb_headroom check out of fr_hard_header and into pvc_xmit.
This has two benefits:
1. Originally we only do this check for skbs sent by users on Ethernet-
emulating PVC devices. After the change we do this check for skbs sent on
normal PVC devices, too.
(Also add a comment to make it clear that this is only a protection
against upper layers that don't take dev->needed_headroom into account.
Such upper layers should be rare and I believe they should be fixed.)
2. After the change we can simplify the parameter list of fr_hard_header.
We no longer need to use a pointer to pointers (skb_p) because we no
longer need to replace the skb inside fr_hard_header.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Keep the code for the normal (non-error) flow at the lowest
indentation level. And use "goto drop" for all error handling.
2. Replace code that pads short Ethernet frames with a "__skb_pad" call.
3. Change "dev_kfree_skb" to "kfree_skb" in error handling code.
"kfree_skb" is the correct function to call when dropping an skb due to
an error. "dev_kfree_skb", which is an alias of "consume_skb", is for
dropping skbs normally (not due to an error).
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fr_hard_header function is used to prepend the header to skbs before
transmission. It is used in 3 situations:
1) When a control packet is generated internally in this driver;
2) When a user sends an skb on an Ethernet-emulating PVC device;
3) When a user sends an skb on a normal PVC device.
These 3 situations need to be handled differently by fr_hard_header.
Different headers should be prepended to the skb in different situations.
Currently fr_hard_header distinguishes these 3 situations using
skb->protocol. For situation 1 and 2, a special skb->protocol value
will be assigned before calling fr_hard_header, so that it can recognize
these 2 situations. All skb->protocol values other than these special ones
are treated by fr_hard_header as situation 3.
However, it is possible that in situation 3, the user sends an skb with
one of the special skb->protocol values. In this case, fr_hard_header
would incorrectly treat it as situation 1 or 2.
This patch tries to solve this issue by using skb->dev instead of
skb->protocol to distinguish between these 3 situations. For situation
1, skb->dev would be NULL; for situation 2, skb->dev->type would be
ARPHRD_ETHER; and for situation 3, skb->dev->type would be ARPHRD_DLCI.
This way fr_hard_header would be able to distinguish these 3 situations
correctly regardless what skb->protocol value the user tries to use in
situation 3.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lmc_trace() was first introduced in commit e7a392d5158af ("Import
2.3.99pre6-5") and was not touched ever since.
The reason for looking at this was to get rid of the in_interrupt() usage,
but while looking at it the following observations were made:
- At least lmc_get_stats() (->ndo_get_stats()) is invoked with disabled
preemption which is not detected by the in_interrupt() check, which
would cause schedule() to be called from invalid context.
- The code is hidden behind #ifdef LMC_TRACE which is not defined within
the kernel and wasn't at the time it was introduced.
- Three jiffies don't match 50ms. msleep() would be a better match which
would also avoid the schedule() invocation. But why have it to begin
with?
- Nobody would do something like this today. Either netdev_dbg() or
trace_printk() or a trace event would be used. If only the functions
related to this driver are interesting then ftrace can be used with
filtering.
As it is obviously broken for years, simply remove it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
1.
Move the lapb_register/lapb_unregister calls into the ndo_open/ndo_stop
functions.
This makes the LAPB protocol start/stop when the network interface
starts/stops. When the network interface is down, the LAPB protocol
shouldn't be running and the LAPB module shoudn't be generating control
frames.
2.
Move netif_start_queue/netif_stop_queue into the ndo_open/ndo_stop
functions.
This makes the TX queue start/stop when the network interface
starts/stops.
(netif_stop_queue was originally in the ndo_stop function. But to make
the code look better, I created a new function to use as ndo_stop, and
made it call the original ndo_stop function. I moved netif_stop_queue
from the original ndo_stop function to the new ndo_stop function.)
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets skb->protocol before transmitting frames on the HDLC
device, so that a user listening on the HDLC device with an AF_PACKET
socket will see outgoing frames' sll_protocol field correctly set and
consistent with that of incoming frames.
1. Control frames in hdlc_cisco and hdlc_ppp
When these drivers send control frames, skb->protocol is not set.
This value should be set to htons(ETH_P_HDLC), because when receiving
control frames, their skb->protocol is set to htons(ETH_P_HDLC).
When receiving, hdlc_type_trans in hdlc.h is called, which then calls
cisco_type_trans or ppp_type_trans. The skb->protocol of control frames
is set to htons(ETH_P_HDLC) so that the control frames can be received
by hdlc_rcv in hdlc.c, which calls cisco_rx or ppp_rx to process the
control frames.
2. hdlc_fr
When this driver sends control frames, skb->protocol is set to internal
values used in this driver.
When this driver sends data frames (from upper stacked PVC devices),
skb->protocol is the same as that of the user data packet being sent on
the upper PVC device (for normal PVC devices), or is htons(ETH_P_802_3)
(for Ethernet-emulating PVC devices).
However, skb->protocol for both control frames and data frames should be
set to htons(ETH_P_HDLC), because when receiving, all frames received on
the HDLC device will have their skb->protocol set to htons(ETH_P_HDLC).
When receiving, hdlc_type_trans in hdlc.h is called, and because this
driver doesn't provide a type_trans function in struct hdlc_proto,
all frames will have their skb->protocol set to htons(ETH_P_HDLC).
The frames are then received by hdlc_rcv in hdlc.c, which calls fr_rx
to process the frames (control frames are consumed and data frames
are re-received on upper PVC devices).
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is a virtual driver stacked on top of Ethernet interfaces.
When this driver transmits data on the Ethernet device, the skb->protocol
setting is inconsistent with the Ethernet header prepended to the skb.
This causes a user listening on the Ethernet interface with an AF_PACKET
socket, to see different sll_protocol values for incoming and outgoing
frames, because incoming frames would have this value set by parsing the
Ethernet header.
This patch changes the skb->protocol value for outgoing Ethernet frames,
making it consistent with the Ethernet header prepended. This makes a
user listening on the Ethernet device with an AF_PACKET socket, to see
the same sll_protocol value for incoming and outgoing frames.
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
x25_type_trans only needs to be called before we call netif_rx to pass
the skb to upper layers.
It does not need to be called before lapb_data_received. The LAPB module
does not need the fields that are set by calling it.
In the other two X.25 drivers - lapbether and hdlc_x25. x25_type_trans
is only called before netif_rx and not before lapb_data_received.
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "SLF_OUTWAIT" flag defined in x25_asy.h is not actually used.
It is only cleared at one place in x25_asy.c but is never read or set.
So we can remove it.
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a couple bugs here:
1) If opt[1] is zero then this results in a forever loop. If the value
is less than 2 then it is invalid.
2) It assumes that "len" is more than sizeof(valid_accm) or 6 which can
result in memory corruption.
In the case of LCP_OPTION_ACCM, then we should check "opt[1]" instead
of "len" because, if "opt[1]" is less than sizeof(valid_accm) then
"nak_len" gets out of sync and it can lead to memory corruption in the
next iterations through the loop. In case of LCP_OPTION_MAGIC, the
only valid value for opt[1] is 6, but the code is trying to log invalid
data so we should only discard the data when "len" is less than 6
because that leads to a read overflow.
Reported-by: ChenNan Of Chaitin Security Research Lab <whutchennan@gmail.com>
Fixes: e022c2f07a ("WAN: new synchronous PPP implementation for generic HDLC.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
PVC devices are virtual devices in this driver stacked on top of the
actual HDLC device. They are the devices normal users would use.
PVC devices have two types: normal PVC devices and Ethernet-emulating
PVC devices.
When transmitting data with PVC devices, the ndo_start_xmit function
will prepend a header of 4 or 10 bytes. Currently this driver requests
this headroom to be reserved for normal PVC devices by setting their
hard_header_len to 10. However, this does not work when these devices
are used with AF_PACKET/RAW sockets. Also, this driver does not request
this headroom for Ethernet-emulating PVC devices (but deals with this
problem by reallocating the skb when needed, which is not optimal).
This patch replaces hard_header_len with needed_headroom, and set
needed_headroom for Ethernet-emulating PVC devices, too. This makes
the driver to request headroom for all PVC devices in all cases.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
Change the default value of hard_header_len in hdlc.c from 16 to 0.
Currently there are 6 HDLC protocol drivers, among them:
hdlc_raw_eth, hdlc_cisco, hdlc_ppp, hdlc_x25 set hard_header_len when
attaching the protocol, overriding the default. So this patch does not
affect them.
hdlc_raw and hdlc_fr don't set hard_header_len when attaching the
protocol. So this patch will change the hard_header_len of the HDLC
device for them from 16 to 0.
This is the correct change because both hdlc_raw and hdlc_fr don't have
header_ops, and the code in net/packet/af_packet.c expects the value of
hard_header_len to be consistent with header_ops.
In net/packet/af_packet.c, in the packet_snd function,
for AF_PACKET/DGRAM sockets it would reserve a headroom of
hard_header_len and call dev_hard_header to fill in that headroom,
and for AF_PACKET/RAW sockets, it does not reserve the headroom and
does not call dev_hard_header, but checks if the user has provided a
header of length hard_header_len (in function dev_validate_header).
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver didn't set hard_header_len. This patch sets hard_header_len
for it according to its header_ops->create function.
This driver's header_ops->create function (cisco_hard_header) creates
a header of (struct hdlc_header), so hard_header_len should be set to
sizeof(struct hdlc_header).
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the skb's network_header before it is passed to the underlying
Ethernet device for transmission.
This patch fixes the following issue:
When we use this driver with AF_PACKET sockets, there would be error
messages of:
protocol 0805 is buggy, dev (Ethernet interface name)
printed in the system "dmesg" log.
This is because skbs passed down to the Ethernet device for transmission
don't have their network_header properly set, and the dev_queue_xmit_nit
function in net/core/dev.c complains about this.
Reason of setting the network_header to this place (at the end of the
Ethernet header, and at the beginning of the Ethernet payload):
Because when this driver receives an skb from the Ethernet device, the
network_header is also set at this place.
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The underlying Ethernet device may request necessary tailroom to be
allocated by setting needed_tailroom. This driver should also set
needed_tailroom to request the tailroom needed by the underlying
Ethernet device to be allocated.
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/wan/dlci.c: In function ‘dlci_close’:
drivers/net/wan/dlci.c:298:8: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Mike McLagan <mike.mclagan@linux.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Added a skb->len check
This driver expects upper layers to include a pseudo header of 1 byte
when passing down a skb for transmission. This driver will read this
1-byte header. This patch added a skb->len check before reading the
header to make sure the header exists.
2. Added needed_headroom and set hard_header_len to 0
When this driver transmits data,
first this driver will remove a pseudo header of 1 byte,
then the lapb module will prepend the LAPB header of 2 or 3 bytes.
So the value of needed_headroom in this driver should be 3 - 1.
Because this driver has no header_ops, according to the logic of
af_packet.c, the value of hard_header_len should be 0.
Reason of setting needed_headroom and hard_header_len at this place:
This driver is written using the API of the hdlc module, the hdlc
module enables this driver (the protocol driver) to run on any hardware
that has a driver (the hardware driver) written using the API of the
hdlc module.
Two other hdlc protocol drivers - hdlc_ppp and hdlc_raw_eth, also set
things like hard_header_len at this place. In hdlc_ppp, it sets
hard_header_len after attach_hdlc_protocol and before setting dev->type.
In hdlc_raw_eth, it sets hard_header_len by calling ether_setup after
attach_hdlc_protocol and after memcpy the settings.
3. Reset needed_headroom when detaching protocols (in hdlc.c)
When detaching a protocol from a hardware device, the hdlc module will
reset various parameters of the device (including hard_header_len) to
the default values. We add needed_headroom here so that needed_headroom
will also be reset.
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Added a skb->len check
This driver expects upper layers to include a pseudo header of 1 byte
when passing down a skb for transmission. This driver will read this
1-byte header. This patch added a skb->len check before reading the
header to make sure the header exists.
2. Added needed_headroom
When this driver transmits data,
first this driver will remove a pseudo header of 1 byte,
then the lapb module will prepend the LAPB header of 2 or 3 bytes.
So the value of needed_headroom in this driver should be 3 - 1.
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Added a skb->len check
This driver expects upper layers to include a pseudo header of 1 byte
when passing down a skb for transmission. This driver will read this
1-byte header. This patch added a skb->len check before reading the
header to make sure the header exists.
2. Changed to use needed_headroom instead of hard_header_len to request
necessary headroom to be allocated
In net/packet/af_packet.c, the function packet_snd first reserves a
headroom of length (dev->hard_header_len + dev->needed_headroom).
Then if the socket is a SOCK_DGRAM socket, it calls dev_hard_header,
which calls dev->header_ops->create, to create the link layer header.
If the socket is a SOCK_RAW socket, it "un-reserves" a headroom of
length (dev->hard_header_len), and assumes the user to provide the
appropriate link layer header.
So according to the logic of af_packet.c, dev->hard_header_len should
be the length of the header that would be created by
dev->header_ops->create.
However, this driver doesn't provide dev->header_ops, so logically
dev->hard_header_len should be 0.
So we should use dev->needed_headroom instead of dev->hard_header_len
to request necessary headroom to be allocated.
This change fixes kernel panic when this driver is used with AF_PACKET
SOCK_RAW sockets.
Call stack when panic:
[ 168.399197] skbuff: skb_under_panic: text:ffffffff819d95fb len:20
put:14 head:ffff8882704c0a00 data:ffff8882704c09fd tail:0x11 end:0xc0
dev:veth0
...
[ 168.399255] Call Trace:
[ 168.399259] skb_push.cold+0x14/0x24
[ 168.399262] eth_header+0x2b/0xc0
[ 168.399267] lapbeth_data_transmit+0x9a/0xb0 [lapbether]
[ 168.399275] lapb_data_transmit+0x22/0x2c [lapb]
[ 168.399277] lapb_transmit_buffer+0x71/0xb0 [lapb]
[ 168.399279] lapb_kick+0xe3/0x1c0 [lapb]
[ 168.399281] lapb_data_request+0x76/0xc0 [lapb]
[ 168.399283] lapbeth_xmit+0x56/0x90 [lapbether]
[ 168.399286] dev_hard_start_xmit+0x91/0x1f0
[ 168.399289] ? irq_init_percpu_irqstack+0xc0/0x100
[ 168.399291] __dev_queue_xmit+0x721/0x8e0
[ 168.399295] ? packet_parse_headers.isra.0+0xd2/0x110
[ 168.399297] dev_queue_xmit+0x10/0x20
[ 168.399298] packet_sendmsg+0xbf0/0x19b0
......
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
- Prepare for tasklet API modernization (Romain Perier, Allen Pais, Kees Cook)
-----BEGIN PGP SIGNATURE-----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=hb+e
-----END PGP SIGNATURE-----
Merge tag 'tasklets-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull tasklets API update from Kees Cook:
"These are the infrastructure updates needed to support converting the
tasklet API to something more modern (and hopefully for removal
further down the road).
There is a 300-patch series waiting in the wings to get set out to
subsystem maintainers, but these changes need to be present in the
kernel first. Since this has some treewide changes, I carried this
series for -next instead of paining Thomas with it in -tip, but it's
got his Ack.
This is similar to the timer_struct modernization from a while back,
but not nearly as messy (I hope). :)
- Prepare for tasklet API modernization (Romain Perier, Allen Pais,
Kees Cook)"
* tag 'tasklets-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
tasklet: Introduce new initialization API
treewide: Replace DECLARE_TASKLET() with DECLARE_TASKLET_OLD()
usb: gadget: udc: Avoid tasklet passing a global
This converts all the existing DECLARE_TASKLET() (and ...DISABLED)
macros with DECLARE_TASKLET_OLD() in preparation for refactoring the
tasklet callback type. All existing DECLARE_TASKLET() users had a "0"
data argument, it has been removed here as well.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
The .suspend() and .resume() callbacks are not defined for this driver.
Still, their power management structure follows the legacy framework. To
bring it under the generic framework, simply remove the binding of
callbacks from "struct pci_driver".
Change code indentation from space to tab in "struct pci_driver".
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed 2 issues with the usage of skb_cow in LAPB drivers
"lapbether" and "hdlc_x25":
1) After skb_cow fails, kfree_skb should be called to drop a reference
to the skb. But in both drivers, kfree_skb is not called.
2) skb_cow should be called before skb_push so that is can ensure the
safety of skb_push. But in "lapbether", it is incorrectly called after
skb_push.
More details about these 2 issues:
1) The behavior of calling kfree_skb on failure is also the behavior of
netif_rx, which is called by this function with "return netif_rx(skb);".
So this function should follow this behavior, too.
2) In "lapbether", skb_cow is called after skb_push. This results in 2
logical issues:
a) skb_push is not protected by skb_cow;
b) An extra headroom of 1 byte is ensured after skb_push. This extra
headroom has no use in this function. It also has no use in the
upper-layer function that this function passes the skb to
(x25_lapb_receive_frame in net/x25/x25_dev.c).
So logically skb_cow should instead be called before skb_push.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is not working because of problems of its receiving code.
This patch fixes it to make it work.
When the driver receives an LAPB frame, it should first pass the frame
to the LAPB module to process. After processing, the LAPB module passes
the data (the packet) back to the driver, the driver should then add a
one-byte pseudo header and pass the data to upper layers.
The changes to the "x25_asy_bump" function and the
"x25_asy_data_indication" function are to correctly implement this
procedure.
Also, the "x25_asy_unesc" function ignores any frame that is shorter
than 3 bytes. However the shortest frames are 2-byte long. So we need
to change it to allow 2-byte frames to pass.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Reviewed-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xie He
Jakub Kicinski
Wang Hai
Andrew Lunn
Tom Rix
David S. Miller
Sebastian Andrzej Siewior
Dan Carpenter
Linus Torvalds
YueHaibing
Joe Perches
Gustavo A. R. Silva
Lee Jones
Christophe JAILLET
Kees Cook
Vaibhav Gupta