Now that the mfd is using the register map cache there's no need for the
CODEC driver to do any register cache management or any funny dances to
interact with the other drivers using the device so just remove the cache
initialisation and volatility information.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Just go directly to the regmap API, saving code and making integration
that bit more direct.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since they don't actually have power bits but do have events associated
with them it's important that we bootstrap their state properly which
making them virtual does.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The existence of this parameter is purely historical. None of the CODEC drivers
uses it and we always pass in the same value anyway, so it should be safe to
remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Still have a manual free in there for some realloc()ed memory as there's
no devm version of that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow systems to override the default microphone detection rates using
platform data in case the settings are not suitable (eg, due to an
unusually noisy jack).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't need to rerun DAPM if the clock source is the same but we do
need to adjust the microphone detection rate in case we are moving from
an audio to a non-audio rate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1811A features an advanced low power accessory detection subsystem
which allows the device to be maintained in a very low power state while
the system is idle without sacrificing any accessory detection features.
Implement software support for this, automatically managing the power
configuration of the device depending on the detected accessory.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8958 and WM1811 support detecting a range of buttons. Allow the
user to provide platform data enabling more of these levels without
having to write a custom detection handler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Actively manage the detection rate for microphones with WM8958, providing
improved power consumption and maximising the benefit from the hardware
debounce.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When we don't have any active audio we can put the microphone biases into
bypass mode to save power at the expense of performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure SYSCLK is enabled while running accessory detection on WM8958.
It is always required so there is no sense in requiring machine drivers
to individually do this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 1ee46ebd("ASoC: Make the DAI ops constant in the DAI structure")
introduced the possibility to have constant DAI ops structures, yet this is
barley used in both existing drivers and also new drivers being submitted,
although none of them modifies its DAI ops structure. The later is not
surprising since existing drivers are often used as templates for new drivers.
So this patch just constifies all existing snd_soc_dai_ops structs to eliminate
the issue altogether.
The patch was generated with the following coccinelle semantic patch:
// <smpl>
@@
identifier ops;
@@
-struct snd_soc_dai_ops ops =
+const struct snd_soc_dai_ops ops =
{ ... };
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Occasionally we may see an accessory reported before we have a stable
impedance for the accessory. If this happens then reread the status in
order to ensure that the handler can take the appropriate action for the
status change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The field is no longer initialised so this will crash if running on
wm8958.
Reported-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The field is no longer initialised so this will crash if running on
wm8958.
Reported-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Evaluation of larger quantities of material has provided new DCS codes
values to be applied for WM1811.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
We set hw_params callback for wm8994_aif3_dai_ops to wm8994_aif3_hw_params.
Thus no need to check wm8994-aif3 in wm8994_hw_params.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For wm8994-aif2, the rate_reg should be WM8994_AIF2_RATE.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
snd_soc_update_bits() will only write new register value
if the old value is different from the new value.
In additional, snd_soc_update_bits() returns 0 for no change.
No need to read WM8994_CLOCKING_1 register before calling snd_soc_update_bits().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1811 is mostly register compatible with the WM8994 and WM8958,
providing a high performance audio hub CODEC in a small form factor
suitable for ultra compact system designs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ALSA doesn't really have good mechanisms for dealing with these so we just
log them - the hardware already has automatic shutdown support.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull control is availalbe for WM8994 AIF2, generally disabled as part of
the GPIO configuration in order to save power after system startup. As on
newer devices in the series there is no GPIO functionality on these pins
this will happen less naturally so have the driver disable the pulls as the
AIF is probed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On WM8994 class devices only the analogue portions of the CODEC require
VMID so when running digital only paths we can leave VMID disabled.
On some earlier devices the FLL uses VMID so we don't use DAPM reference
counting alone, we maintain an internal reference count which is also
enabled and disabled by the FLL startup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Currently this does not actually do anything, it is being introduced in
order to facilitate additional power optimisations for current generation
devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This error would have no effect on current silicon revisions, the fall
through case has the same behaviour.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Some devices can have performance optimized by setting different offsets
for left and right channels.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Later WM8994 devices implement a new DC servo readback mode with the
register used to access the offset moved to register 0x59. Implement
support for this and enable it on the appropriate devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The WM8994 and WM8958 series of devices have two MICBIAS supplies rather
than one, the current widget actually manages the microphone detection
control register bit (which is managed separately by the relevant API).
Fix this, hooking the relevant supplies up to the MICBIAS1 and MICBIAS2
widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
If DAIs are idle but their clocks are in use for some reason (eg, as
SYSCLK or for accessory detect) then set the clock dividers to the maximum
to reduce slightly the power consumption of the unclocked circuits.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Try the completion before we start the FLL so that if an interrupt was
delayed long enough for us to miss it we don't wait for the completion
it signalled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown
Lars-Peter Clausen
Axel Lin