This patch adds a driver for Fixed MMIO clock.
The driver reads a clock frequency value from a single 32-bit memory
mapped register and registers it as a fixed rate clock.
It can be enabled with COMMON_CLK_FIXED_MMIO Kconfig option.
Signed-off-by: Jan Kotas <jank@cadence.com>
[sboyd@kernel.org: Make of_fixed_mmio_clk_setup() static, use clk_hw
based APIs]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Commit d360b130e2 ("clk: imx: Make the i.MX8MQ CCM clock driver
CLK_IMX8MQ dependant") introduced this duplicate and incorrectly ordered
kconfig include.
Fixes: d360b130e2 ("clk: imx: Make the i.MX8MQ CCM clock driver CLK_IMX8MQ dependant")
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Remove the dependency between the i.MX8MQ CCM clock driver
and the CONFIG_SOC_IMX8MQ and use CONFIG_CLK_IMX8MQ instead.
CONFIG_CLK_IMX8MQ depends on ARCH_MXC && ARM64.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The patch introduces CONFIG_MXC_CLK option for legacy MMIO clocks,
this is required to compile legacy MMIO clock conditionally when adding
SCU based clocks for MX8 platforms later.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
ROHM bd71837 and bd71847 contain 32768Hz clock gate. Support the clock
using generic clock framework. Note, only bd71837 is tested but bd71847
should be identical what comes to clk parts.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
because of summer time holidays/vacations. The biggest change in the diffstat
is in the Qualcomm clk driver, where they got support for CPUs and handful of
SoCs. After that, the at91 driver got a major rewrite for newer DT bindings
that should make things easier going forward and the TI code moved to a
clockdomain based design. The long tail is mostly small driver updates for
newer clks and some simpler SoC clock drivers such as the Hisilicon and imx
support.
In the core framework, we only have two small changes this time. One is a new
clk API to get all clks for a device with the bulk clk APIs. This allows
drivers that don't care about doing anything besides turning on all the clks to
just clk_get() them all and turn them on. The other change is the beginning of
a way to support save and restore of clk settings in the clk framework. TI is
the only user right now, but we will want to expand upon this design in the
future to support more save and restore of clk registers. At least this gets
us started and works well enough for one SoC, but there's more work in the
future.
Core:
- clk_bulk_get_all() API and friends to get all the clks for a device
- Basic clk state save/restore hooks
New Drivers:
- Renesas RZ/A2 (R7S9210) SoC, including early clocks
- Rensas RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs
- Rensas RZ/G2M (r8a774a1) SoC
- Qualcomm Krait CPU clk support
- Qualcomm QCS404 GCC support
- Qualcomm SDM660 GCC support
- Qualcomm SDM845 camera clock controller
- Ingenic jz4725b CGU
- Hisilicon 3670 SoC support
- TI SCI clks on K3 SoCs
- iMX6 MMDC clks
- Reset Controller (RMU) support for Actions Semi Owl S900 and S700 SoCs
Updates:
- Rework at91 PMC clock driver for new DT bindings
- Nvidia Tegra clk driver MBIST workaround fix
- S2RAM support for Marvell mvebu periph clks
- Use updated printk format for OF node names
- Fix TI code to only search DT subnodes
- Various static analysis finds
- Tag various drivers with SPDX license tags
- Support dynamic frequency switching (DFS) on qcom SDM845 GCC
- Only use s2mps11 dt-binding defines instead of redefining them in the driver
- Add some more missing clks to qcom MSM8996 GCC
- Quad SPI clks on qcom SDM845
- Add support for CMT timer clocks on R-Car V3H
- Add support for SHDI and various timer clocks on R-Car V3M
- Improve OSC and RCLK (watchdog) handling on R-Car Gen3 SoCs
- Amlogic clk-pll driver improvements and updates
- Amlogic axg audio controller system clocks
- Register Amlogic meson8b clock controller early
- Add support for SATA and Fine Display Processor (FDP) clocks on R-Car M3-N
- Consolidation of system suspend related code in Exynos, S5P, S3C SoC clk drivers
- Fixes for system suspend support on Exynos542x (Odroid boards) and Exynos5433 SoC
- Remove obsoleted Exynos4212 ISP clock definitions
- Migrated TI am3/4/5 and dra7 SoCs to clockdomain based design
- TI RTC+DDR sleep mode support for clock save/restore
- Allwinner A64 display engine support and fixes
- Allwinner A83t display engine support and fixes
-----BEGIN PGP SIGNATURE-----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=V5aK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time it looks like a quieter release cycle in the clk tree. I
guess that's because of summer time holidays/vacations. The biggest
change in the diffstat is in the Qualcomm clk driver, where they got
support for CPUs and handful of SoCs. After that, the at91 driver got
a major rewrite for newer DT bindings that should make things easier
going forward and the TI code moved to a clockdomain based design.
The long tail is mostly small driver updates for newer clks and some
simpler SoC clock drivers such as the Hisilicon and imx support.
In the core framework, we only have two small changes this time.
One is a new clk API to get all clks for a device with the bulk clk
APIs. This allows drivers that don't care about doing anything besides
turning on all the clks to just clk_get() them all and turn them on.
The other change is the beginning of a way to support save and restore
of clk settings in the clk framework. TI is the only user right now,
but we will want to expand upon this design in the future to support
more save and restore of clk registers. At least this gets us started
and works well enough for one SoC, but there's more work in the
future.
Core:
- clk_bulk_get_all() API and friends to get all the clks for a device
- Basic clk state save/restore hooks
New Drivers:
- Renesas RZ/A2 (R7S9210) SoC, including early clocks
- Rensas RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs
- Rensas RZ/G2M (r8a774a1) SoC
- Qualcomm Krait CPU clk support
- Qualcomm QCS404 GCC support
- Qualcomm SDM660 GCC support
- Qualcomm SDM845 camera clock controller
- Ingenic jz4725b CGU
- Hisilicon 3670 SoC support
- TI SCI clks on K3 SoCs
- iMX6 MMDC clks
- Reset Controller (RMU) support for Actions Semi Owl S900 and S700 SoCs
Updates:
- Rework at91 PMC clock driver for new DT bindings
- Nvidia Tegra clk driver MBIST workaround fix
- S2RAM support for Marvell mvebu periph clks
- Use updated printk format for OF node names
- Fix TI code to only search DT subnodes
- Various static analysis finds
- Tag various drivers with SPDX license tags
- Support dynamic frequency switching (DFS) on qcom SDM845 GCC
- Only use s2mps11 dt-binding defines instead of redefining them in the driver
- Add some more missing clks to qcom MSM8996 GCC
- Quad SPI clks on qcom SDM845
- Add support for CMT timer clocks on R-Car V3H
- Add support for SHDI and various timer clocks on R-Car V3M
- Improve OSC and RCLK (watchdog) handling on R-Car Gen3 SoCs
- Amlogic clk-pll driver improvements and updates
- Amlogic axg audio controller system clocks
- Register Amlogic meson8b clock controller early
- Add support for SATA and Fine Display Processor (FDP) clocks on R-Car M3-N
- Consolidation of system suspend related code in Exynos, S5P, S3C SoC clk drivers
- Fixes for system suspend support on Exynos542x (Odroid boards) and Exynos5433 SoC
- Remove obsoleted Exynos4212 ISP clock definitions
- Migrated TI am3/4/5 and dra7 SoCs to clockdomain based design
- TI RTC+DDR sleep mode support for clock save/restore
- Allwinner A64 display engine support and fixes
- Allwinner A83t display engine support and fixes"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (186 commits)
clk: qcom: Remove unused arrays in SDM845 GCC
clk: fixed-rate: fix of_node_get-put imbalance
clk: s2mps11: Add used attribute to s2mps11_dt_match
clk: qcom: gcc-sdm660: Add MODULE_LICENSE
clk: qcom: Add safe switch hook for krait mux clocks
dt-bindings: clock: Document qcom,krait-cc
clk: qcom: Add Krait clock controller driver
dt-bindings: arm: Document qcom,kpss-gcc
clk: qcom: Add KPSS ACC/GCC driver
clk: qcom: Add support for Krait clocks
clk: qcom: Add IPQ806X's HFPLLs
clk: qcom: Add MSM8960/APQ8064's HFPLLs
dt-bindings: clock: Document qcom,hfpll
clk: qcom: Add HFPLL driver
clk: qcom: Add support for High-Frequency PLLs (HFPLLs)
ARM: Add Krait L2 register accessor functions
clk: imx6q: add mmdc0 ipg clock
clk: imx6sl: add mmdc ipg clocks
clk: imx6sll: add mmdc1 ipg clock
clk: imx6sx: add mmdc1 ipg clock
...
Previously, the CGU code corresponding to the SoC for which we're
compiling the kernel was the only one enabled, which made it impossible
to build one kernel that supports them all.
Now, it is possible to select more than one SoC to support.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch adds CCF compliant clock driver for ZynqMP.
Clock driver queries supported clock information from
firmware and regiters pll and output clocks with CCF.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Tejas Patel <tejasp@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Jolly Shah <jolly.shah@xilinx.com>
Acked-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds a driver for MAX9485, a programmable audio clock generator.
The device requires a 27.000 MHz clock input. It can provide a gated
buffered output of its input clock and two gated outputs of a PLL that can
generate one out of 16 discrete frequencies. There is only one PLL however,
so the two gated outputs will always have the same frequency but they can
be switched individually.
The driver for this device exposes 4 clocks in total:
- MAX9485_MCLKOUT: A gated, buffered output of the input clock
- MAX9485_CLKOUT: A PLL that can be configured to 16 different
discrete frequencies
- MAX9485_CLKOUT[1,2]: Two gated outputs for MAX9485_CLKOUT
Some PLL output frequencies can be achieved with different register
settings. The driver will select the one with lowest jitter in such cases.
Signed-off-by: Daniel Mack <daniel@zonque.org>
[sboyd@kernel.org: Use local variable for val in max9485_clkout_recalc_rate()
and shorten line of max9485_of_clk_get()]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
general cleanups, but nothing too major. The majority of the diff goes to
two SoCs, Actions Semi and Qualcomm. A brand new driver is introduced for
Actions Semi so it takes up some lines to add all the different types, and
the Qualcomm diff is there because we add support for two SoCs and it's quite
a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic platforms. And
then the long tail of driver updates for various fixes and stuff follows
after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock
-----BEGIN PGP SIGNATURE-----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=KK/v
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time we have a good set of changes to the core framework that do
some general cleanups, but nothing too major. The majority of the diff
goes to two SoCs, Actions Semi and Qualcomm. A brand new driver is
introduced for Actions Semi so it takes up some lines to add all the
different types, and the Qualcomm diff is there because we add support
for two SoCs and it's quite a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic
platforms. And then the long tail of driver updates for various fixes
and stuff follows after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
clk: qcom: Export clk_fabia_pll_configure()
clk: bcm: Update and add Stingray clock entries
dt-bindings: clk: Update Stingray binding doc
clk-si544: Properly round requested frequency to nearest match
clk: ingenic: jz4770: Add 150us delay after enabling VPU clock
clk: ingenic: jz4770: Enable power of AHB1 bus after ungating VPU clock
clk: ingenic: jz4770: Modify C1CLK clock to disable CPU clock stop on idle
clk: ingenic: jz4770: Change OTG from custom to standard gated clock
clk: ingenic: Support specifying "wait for clock stable" delay
clk: ingenic: Add support for clocks whose gate bit is inverted
clk: use match_string() helper
clk: bcm2835: use match_string() helper
clk: Return void from debug_init op
clk: remove clk_debugfs_add_file()
clk: tegra: no need to check return value of debugfs_create functions
clk: davinci: no need to check return value of debugfs_create functions
clk: bcm2835: no need to check return value of debugfs_create functions
clk: no need to check return value of debugfs_create functions
clk: imx6: add EPIT clock support
clk: mvebu: use correct bit for 98DX3236 NAND
...
Clock driver is mandatory if the machine is selected.
Then don't use 'bool' and 'depends on' commands, but 'def_bool'
with the machine(s).
Fixes: da32d3539f ("clk: stm32: add configuration flags for each of the stm32 drivers")
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
for the TI Davinci family of SoCs. So far those clks have been supported
with a custom implementation of the clk API in the arch port instead of in
the CCF. With this driver merged we're one step closer to having a single
clk API implementation.
The other large diff is from the Amlogic clk driver that underwent some
major surgery to use regmap. Beyond that, the biggest hitter is Samsung
which needed some reworks to properly handle clk provider power domains
and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some cleanups
and small fixes for some of the more esoteric features. And the usual
set of driver non-critical fixes, cleanups, and minor additions are here as
well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC
-----BEGIN PGP SIGNATURE-----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=ys4O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The large diff this time around is from the addition of a new clk
driver for the TI Davinci family of SoCs. So far those clks have been
supported with a custom implementation of the clk API in the arch port
instead of in the CCF. With this driver merged we're one step closer
to having a single clk API implementation.
The other large diff is from the Amlogic clk driver that underwent
some major surgery to use regmap. Beyond that, the biggest hitter is
Samsung which needed some reworks to properly handle clk provider
power domains and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some
cleanups and small fixes for some of the more esoteric features. And
the usual set of driver non-critical fixes, cleanups, and minor
additions are here as well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (233 commits)
clk: davinci: add a reset lookup table for psc0
clk: imx: add clock driver for imx6sll
dt-bindings: imx: update clock doc for imx6sll
clk: imx: add new gate/gate2 wrapper funtion
clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux
clk: cs2000: set pm_ops in hibernate-compatible way
clk: bcm2835: De-assert/assert PLL reset signal when appropriate
clk: imx7d: Move clks_init_on before any clock operations
clk: imx7d: Correct ahb clk parent select
clk: imx7d: Correct dram pll type
clk: imx7d: Add USB clock information
clk: socfpga: stratix10: add clock driver for Stratix10 platform
dt-bindings: documentation: add clock bindings information for Stratix10
clk: ti: fix flag space conflict with clkctrl clocks
clk: uniphier: add additional ethernet clock lines for Pro4
clk: uniphier: add SATA clock control support
clk: uniphier: add PCIe clock control support
clk: Add driver for the si544 clock generator chip
clk: davinci: Remove redundant dev_err calls
clk: uniphier: add ethernet clock control support for PXs3
...
Add support for Actions Semi common clock driver with generic structures
and interface functions.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk-davinci:
clk: davinci: Remove redundant dev_err calls
clk: davinci: cfgchip: Add TI DA8XX USB PHY clocks
clk: davinci: New driver for TI DA8XX CFGCHIP clocks
dt-bindings: clock: Add bindings for DA8XX CFGCHIP clocks
clk: davinci: Add platform information for TI DM646x PSC
clk: davinci: Add platform information for TI DM644x PSC
clk: davinci: Add platform information for TI DM365 PSC
clk: davinci: Add platform information for TI DM355 PSC
clk: davinci: Add platform information for TI DA850 PSC
clk: davinci: Add platform information for TI DA830 PSC
clk: davinci: New driver for davinci PSC clocks
dt-bindings: clock: New bindings for TI Davinci PSC
clk: davinci: Add platform information for TI DM646x PLL
clk: davinci: Add platform information for TI DM644x PLL
clk: davinci: Add platform information for TI DM365 PLL
clk: davinci: Add platform information for TI DM355 PLL
clk: davinci: Add platform information for TI DA850 PLL
clk: davinci: Add platform information for TI DA830 PLL
clk: davinci: New driver for davinci PLL clocks
dt-bindings: clock: Add new bindings for TI Davinci PLL clocks
* clk-si544:
clk: Add driver for the si544 clock generator chip
* clk-rockchip:
clk: rockchip: assign correct id for pclk_ddr and hclk_sd in rk3399
clk: rockchip: Fix error return in phase clock registration
clk: rockchip: Correct the behaviour of restoring cached phase
clk: rockchip: Fix wrong parents for MMC phase clock for rk3328
clk: rockchip: Fix wrong parent for SDMMC phase clock for rk3228
clk: rockchip: Add 1.6GHz PLL rate for rk3399
clk: rockchip: Restore the clock phase after the rate was changed
clk: rockchip: Prevent calculating mmc phase if clock rate is zero
clk: rockchip: Free the memory on the error path
clk: rockchip: document hdmi_phy external input for rk3328
clk: rockchip: add flags for rk3328 dclk_lcdc
clk: rockchip: remove ignore_unused flag from rk3328 vio_h2p clocks
clk: rockchip: protect all remaining rk3328 interconnect clocks
clk: rockchip: export sclk_hdmi_sfc on rk3328
clk: rockchip: remove HCLK_VIO from rk3328 dt header
clk: rockchip: fix hclk_vio_niu on rk3328
* clk-uniphier:
clk: uniphier: add additional ethernet clock lines for Pro4
clk: uniphier: add SATA clock control support
clk: uniphier: add PCIe clock control support
clk: uniphier: add ethernet clock control support for PXs3
clk: uniphier: add Pro4/Pro5/PXs2 audio system clock
* clk-ti-flag-fix:
clk: ti: fix flag space conflict with clkctrl clocks
clk: ti: clkctrl: add support for CLK_SET_RATE_PARENT flag
This patch adds the driver and devicetree documentation for the
Silicon Labs SI544 clock generator chip. This is an I2C controlled
oscillator capable of generating clock signals ranging from 200kHz
to 1500MHz.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
[sboyd: assign max_freq to 0 in is_valid_frequency() to squelch warning]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Without COMMON_CLK_HI655X Wifi and bluetooth are non-functional on Hikey.
As suggested by Arnd, enable the driver automatically when the parent
driver is selected. With sensible defaults in place, we can leave other
choices for EXPERT.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Suggested-by: Arnd Bergmann <arnd@linaro.org>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add two configuration flags to be able to not compile all the time
stm32f and stm32h7 drivers when ARCH_STM32 is set.
That help to save some space on those small platforms.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch introduces the mechanism to probe stm32mp1 driver.
It also defines registers definition.
This patch also introduces the generic mechanism to register
a clock (a simple gate, divider and fixed factor).
All clocks will be defined in one table.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control. System Control and Management Interface(SCMI) Message Protocol
is defined for the communication between the Application Cores(AP)
and the SCP.
This patch adds support for the clocks provided by SCP using SCMI
protocol.
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
* clk-aspeed:
clk: aspeed: Handle inverse polarity of USB port 1 clock gate
clk: aspeed: Fix return value check in aspeed_cc_init()
clk: aspeed: Add reset controller
clk: aspeed: Register gated clocks
clk: aspeed: Add platform driver and register PLLs
clk: aspeed: Register core clocks
clk: Add clock driver for ASPEED BMC SoCs
dt-bindings: clock: Add ASPEED constants
* clk-lock-UP:
clk: fix reentrancy of clk_enable() on UP systems
* clk-mediatek:
clk: mediatek: adjust dependency of reset.c to avoid unexpectedly being built
clk: mediatek: Fix all warnings for missing struct clk_onecell_data
clk: mediatek: fixup test-building of MediaTek clock drivers
clk: mediatek: group drivers under indpendent menu
* clk-allwinner:
clk: sunxi-ng: a83t: Add M divider to TCON1 clock
clk: sunxi-ng: fix the A64/H5 clock description of DE2 CCU
clk: sunxi-ng: add support for Allwinner H3 DE2 CCU
dt-bindings: fix the binding of Allwinner DE2 CCU of A83T and H3
clk: sunxi-ng: sun8i: a83t: Use sigma-delta modulation for audio PLL
clk: sunxi-ng: sun8i: a83t: Add /2 fixed post divider to audio PLL
clk: sunxi-ng: Support fixed post-dividers on NM style clocks
clk: sunxi-ng: sun50i: a64: Add 2x fixed post-divider to MMC module clocks
clk: sunxi-ng: Support fixed post-dividers on MP style clocks
clk: sunxi: Use PTR_ERR_OR_ZERO()
This adds the stub of a driver for the ASPEED SoCs. The clocks are
defined and the static registration is set up.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Added Spreadtrum's clock driver framework together with common
structures and interface functions.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The RK808 and RK805 PMICs are using a similar register map.
We can reuse the clk driver for the RK805 PMIC. So let's add
the RK805 in the Kconfig description.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
HSDK board manages its clocks using various PLLs. These PLL have same
dividers and corresponding control registers mapped to different addresses.
So we add one common driver for such PLLs.
Each PLL on HSDK board consists of three dividers: IDIV, FBDIV and
ODIV. Output clock value is managed using these dividers.
We add pre-defined tables with supported rate values and appropriate
configurations of IDIV, FBDIV and ODIV for each value.
As of today we add support for PLLs that generate clock for the
HSDK arc cpus, system, ddr, AXI tunnel and hdmi.
By this patch we add support for several plls (arc cpus pll and others),
so we had to use two different init types: CLK_OF_DECLARE for arc cpus pll
and regular probing for others plls.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Update IDT VersaClock 5 driver to support IDT VersaClock 6 5P49V6901.
This chip has two clock inputs (external XTAL or external CLKIN), four
fractional dividers (FODs) and five clock outputs (four universal clock
outputs and one reference clock output at OUT0_SELB_I2C).
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
on Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pull MIPS updates from Ralf Baechle:
"Boston platform support:
- Document DT bindings
- Add CLK driver for board clocks
CM:
- Avoid per-core locking with CM3 & higher
- WARN on attempt to lock invalid VP, not BUG
CPS:
- Select CONFIG_SYS_SUPPORTS_SCHED_SMT for MIPSr6
- Prevent multi-core with dcache aliasing
- Handle cores not powering down more gracefully
- Handle spurious VP starts more gracefully
DSP:
- Add lwx & lhx missaligned access support
eBPF:
- Add MIPS support along with many supporting change to add the
required infrastructure
Generic arch code:
- Misc sysmips MIPS_ATOMIC_SET fixes
- Drop duplicate HAVE_SYSCALL_TRACEPOINTS
- Negate error syscall return in trace
- Correct forced syscall errors
- Traced negative syscalls should return -ENOSYS
- Allow samples/bpf/tracex5 to access syscall arguments for sane
traces
- Cleanup from old Kconfig options in defconfigs
- Fix PREF instruction usage by memcpy for MIPS R6
- Fix various special cases in the FPU eulation
- Fix some special cases in MIPS16e2 support
- Fix MIPS I ISA /proc/cpuinfo reporting
- Sort MIPS Kconfig alphabetically
- Fix minimum alignment requirement of IRQ stack as required by
ABI / GCC
- Fix special cases in the module loader
- Perform post-DMA cache flushes on systems with MAARs
- Probe the I6500 CPU
- Cleanup cmpxchg and add support for 1 and 2 byte operations
- Use queued read/write locks (qrwlock)
- Use queued spinlocks (qspinlock)
- Add CPU shared FTLB feature detection
- Handle tlbex-tlbp race condition
- Allow storing pgd in C0_CONTEXT for MIPSr6
- Use current_cpu_type() in m4kc_tlbp_war()
- Support Boston in the generic kernel
Generic platform:
- yamon-dt: Pull YAMON DT shim code out of SEAD-3 board
- yamon-dt: Support > 256MB of RAM
- yamon-dt: Use serial* rather than uart* aliases
- Abstract FDT fixup application
- Set RTC_ALWAYS_BCD to 0
- Add a MAINTAINERS entry
core kernel:
- qspinlock.c: include linux/prefetch.h
Loongson 3:
- Add support
Perf:
- Add I6500 support
SEAD-3:
- Remove GIC timer from DT
- Set interrupt-parent per-device, not at root node
- Fix GIC interrupt specifiers
SMP:
- Skip IPI setup if we only have a single CPU
VDSO:
- Make comment match reality
- Improvements to time code in VDSO"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (86 commits)
locking/qspinlock: Include linux/prefetch.h
MIPS: Fix MIPS I ISA /proc/cpuinfo reporting
MIPS: Fix minimum alignment requirement of IRQ stack
MIPS: generic: Support MIPS Boston development boards
MIPS: DTS: img: Don't attempt to build-in all .dtb files
clk: boston: Add a driver for MIPS Boston board clocks
dt-bindings: Document img,boston-clock binding
MIPS: Traced negative syscalls should return -ENOSYS
MIPS: Correct forced syscall errors
MIPS: Negate error syscall return in trace
MIPS: Drop duplicate HAVE_SYSCALL_TRACEPOINTS select
MIPS16e2: Provide feature overrides for non-MIPS16 systems
MIPS: MIPS16e2: Report ASE presence in /proc/cpuinfo
MIPS: MIPS16e2: Subdecode extended LWSP/SWSP instructions
MIPS: MIPS16e2: Identify ASE presence
MIPS: VDSO: Fix a mismatch between comment and preprocessor constant
MIPS: VDSO: Add implementation of gettimeofday() fallback
MIPS: VDSO: Add implementation of clock_gettime() fallback
MIPS: VDSO: Fix conversions in do_monotonic()/do_monotonic_coarse()
MIPS: Use current_cpu_type() in m4kc_tlbp_war()
...
Add a driver for the clocks provided by the MIPS Boston board from
Imagination Technologies. 2 clocks are provided - the system clock & the
CPU clock - and each is a simple fixed rate clock whose frequency can be
determined by reading a register provided by the board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16483/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Cortina Systems Gemini (SL3516/CS3516) has an on-chip clock
controller that derive all clocks from a single crystal, using some
documented and some undocumented PLLs, half dividers, counters and
gates. This is a best attempt to construct a clock driver for the
clocks so at least we can gate off unused hardware and driver the
PCI bus clock.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[sboyd@codeaurora.org: Fix devm_ioremap_resource() return value
checking]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In K2G, the clock handling is done through firmware executing on a
separate core. Linux kernel needs to communicate to the firmware
through TI system control interface to access any power management
related resources, including clocks.
The keystone sci-clk driver does this, by communicating to the
firmware through the TI SCI driver. The driver adds support for
registering clocks through DT, and basic required clock operations
like prepare/get_rate, etc.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[sboyd@codeaurora.org: Make ti_sci_init_clocks() static]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The hi655x multi function device is a PMIC providing regulators.
The PMIC also provides a clock for the WiFi and the Bluetooth, let's implement
this clock in order to add it in the hi655x MFD and allow proper wireless
initialization.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[sboyd@codeaurora.org: Remove clkdev usage]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These
chips have two clock inputs, XTAL or CLK, which are muxed into single
PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip
while the 5P49V5923 requires external XTAL.
The PLL feeds two fractional dividers. Each fractional divider feeds
output mux, which allows selecting between clock from the fractional
divider itself or from output mux on output N-1. In case of output
mux 0, the output N-1 is instead connected to the output from the mux
feeding the PLL.
The driver thus far supports only the 5P49V5923 and 5P49V5933, while
it should be easily extensible to the whole 5P49V59xx family of chips
as they are all pretty similar.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The CDCE925 is a member of the CDCE(L)9xx programmable clock generator
family. There are also CDCE913, CDCE937, CDCE949 which have different
number of PLLs and outputs.
The clk-cdce925 driver supports only CDCE925 in the family. This adds
support for the CDCE913, CDCE937, CDCE949, too.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Cc: Michael Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
s2mps11 and max77686 clock drivers can be compile tested to increase
build coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This includes UniPhier clock driver code, except SoC-specific
data arrays.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a Kconfig to define clock configuration for each SoC, and
modify the Makefile to build drivers that only selected in config.
Signed-off-by: Shunli Wang <shunli.wang@mediatek.com>
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Tested-by: John Crispin <blogic@openwrt.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Maxim Max77620 has one 32KHz clock output and the clock HW
IP used on this PMIC is same as what it is there in the MAX77686.
Add clock driver support for MAX77620 on the MAX77686 driver.
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
CC: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clock IP used on the Maxim PMICs max77686 and max77802 are
same. The configuration of clock register is also same except
the number of clocks.
Part of common code utilisation, there is 3 files for these chips
clock driver, one for common and two files for driver registration.
Combine both drivers into single file and move common code into
same common file reduces the 2 files and make max77686 and max77802
clock driver in single fine. This driver does not depends on the
parent driver structure. The regmap handle is acquired through
regmap APIs for the register access.
This combination of driver helps on adding clock driver for different
Maxim PMICs which has similar clock IP like MAX77620 and MAX20024.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
CC: Javier Martinez Canillas <javier@dowhile0.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clk-oxnas driver is specific to its architecture, so do not
propose it on other architectures, unless build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160707091844.196a7930@endymion
Start our new clock infrastructure by adding the registration code, common
structure and common code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160629190535.11855-3-maxime.ripard@free-electrons.com
The RK808 and RK818 PMICs are using a similar register map.
We can reuse the clk driver for the RK818 PMIC. So let's add
the RK818 in the Kconfig description.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1464850228-17244-4-git-send-email-w.egorov@phytec.de
Break the AmLogic clock code up so that only the necessary parts are
compiled and linked. The core code is selected by both arm and arm64
builds with COMMON_CLK_AMLOGIC. The individual drivers have their own
config options as well.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
do have a couple core changes in here as well.
Core:
- CLK_IS_CRITICAL support has been added. This should allow drivers
to properly express that a certain clk should stay on even if
their prepare/enable count drops to 0 (and in turn the parents of
these clks should stay enabled).
- A clk registration API has been added, clk_hw_register(), and
an OF clk provider API has been added, of_clk_add_hw_provider().
These APIs have been put in place to further split clk providers
from clk consumers, with the goal being to have clk providers
never deal with struct clk pointers at all. Conversion of provider
drivers is on going. clkdev has also gained support for registering
clk_hw pointers directly so we can convert drivers that don't use
devicetree.
New Drivers:
- Marvell ap806 and cp110 system controllers (with clks inside!)
- Hisilicon Hi3519 clock and reset controller
- Axis ARTPEC-6 clock controllers
- Oxford Semiconductor OXNAS clock controllers
- AXS10X I2S PLL
- Rockchip RK3399 clock and reset controller
Updates:
- MMC2 and UART2 clks on Samsung Exynos 3250, ACLK on Samsung Exynos 542x
SoCs, and some more clk ID exporting for bus frequency scaling
- Proper BCM2835 PCM clk support and various other clks
- i.MX clk updates for i.MX6SX, i.MX7, and VF610
- Renesas updates for R-Car H3
- Tegra210 got updates for DisplayPort and HDMI 2.0
- Rockchip driver refactorings and fixes due to adding RK3399 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=aEzb
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"It's the usual big pile of driver updates and additions, but we do
have a couple core changes in here as well.
Core:
- CLK_IS_CRITICAL support has been added. This should allow drivers
to properly express that a certain clk should stay on even if their
prepare/enable count drops to 0 (and in turn the parents of these
clks should stay enabled).
- A clk registration API has been added, clk_hw_register(), and an OF
clk provider API has been added, of_clk_add_hw_provider(). These
APIs have been put in place to further split clk providers from clk
consumers, with the goal being to have clk providers never deal
with struct clk pointers at all. Conversion of provider drivers is
on going. clkdev has also gained support for registering clk_hw
pointers directly so we can convert drivers that don't use
devicetree.
New Drivers:
- Marvell ap806 and cp110 system controllers (with clks inside!)
- Hisilicon Hi3519 clock and reset controller
- Axis ARTPEC-6 clock controllers
- Oxford Semiconductor OXNAS clock controllers
- AXS10X I2S PLL
- Rockchip RK3399 clock and reset controller
Updates:
- MMC2 and UART2 clks on Samsung Exynos 3250, ACLK on Samsung Exynos
542x SoCs, and some more clk ID exporting for bus frequency scaling
- Proper BCM2835 PCM clk support and various other clks
- i.MX clk updates for i.MX6SX, i.MX7, and VF610
- Renesas updates for R-Car H3
- Tegra210 got updates for DisplayPort and HDMI 2.0
- Rockchip driver refactorings and fixes due to adding RK3399 support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (139 commits)
clk: fix critical clock locking
clk: qcom: mmcc-8996: Remove clocks that should be controlled by RPM
clk: ingenic: Allow divider value to be divided
clk: sunxi: Add display and TCON0 clocks driver
clk: rockchip: drop old_rate calculation on pll rate changes
clk: rockchip: simplify GRF handling in pll clocks
clk: rockchip: lookup General Register Files in rockchip_clk_init
clk: rockchip: fix the rk3399 sdmmc sample / drv name
clk: mvebu: new driver for Armada CP110 system controller
dt-bindings: arm: add DT binding for Marvell CP110 system controller
clk: mvebu: new driver for Armada AP806 system controller
clk: hisilicon: add CRG driver for hi3519 soc
clk: hisilicon: export some hisilicon APIs to modules
reset: hisilicon: add reset controller driver for hisilicon SOCs
clk: bcm/kona: Do not use sizeof on pointer type
clk: qcom: msm8916: Fix crypto clock flags
clk: nxp: lpc18xx: Initialize clk_init_data::flags to 0
clk/axs10x: Add I2S PLL clock driver
clk: imx7d: fix ahb clock mux 1
clk: fix comment of devm_clk_hw_register()
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.7. Here's the summary of
the changes:
- ATH79: Support for DTB passuing using the UHI boot protocol
- ATH79: Remove support for builtin DTB.
- ATH79: Add zboot debug serial support.
- ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
and DPT-Module.
- ATH79: Update devicetree clock support for AR9132 and AR9331.
- ATH79: Cleanup the DT code.
- ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
- ATH79: Fix regression in PCI window initialization.
- BCM47xx: Move SPROM driver to drivers/firmware/
- BCM63xx: Enable partition parser in defconfig.
- BMIPS: BMIPS5000 has I cache filing from D cache
- BMIPS: BMIPS: Add cpu-feature-overrides.h
- BMIPS: Add Whirlwind support
- BMIPS: Adjust mips-hpt-frequency for BCM7435
- BMIPS: Remove maxcpus from BCM97435SVMB DTS
- BMIPS: Add missing 7038 L1 register cells to BCM7435
- BMIPS: Various tweaks to initialization code.
- BMIPS: Enable partition parser in defconfig.
- BMIPS: Cache tweaks.
- BMIPS: Add UART, I2C and SATA devices to DT.
- BMIPS: Add BCM6358 and BCM63268support
- BMIPS: Add device tree example for BCM6358.
- BMIPS: Improve Improve BCM6328 and BCM6368 device trees
- Lantiq: Add support for device tree file from boot loader
- Lantiq: Allow build with no built-in DT.
- Loongson 3: Reserve 32MB for RS780E integrated GPU.
- Loongson 3: Fix build error after ld-version.sh modification
- Loongson 3: Move chipset ACPI code from drivers to arch.
- Loongson 3: Speedup irq processing.
- Loongson 3: Add basic Loongson 3A support.
- Loongson 3: Set cache flush handlers to nop.
- Loongson 3: Invalidate special TLBs when needed.
- Loongson 3: Fast TLB refill handler.
- MT7620: Fallback strategy for invalid syscfg0.
- Netlogic: Fix CP0_EBASE redefinition warnings
- Octeon: Initialization fixes
- Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
- Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
- Octeon: Correctly handle endian-swapped initramfs images.
- Octeon: Support CN73xx, CN75xx and CN78xx.
- Octeon: Remove dead code from cvmx-sysinfo.
- Octeon: Extend number of supported CPUs past 32.
- Octeon: Remove some code limiting NR_IRQS to 255.
- Octeon: Simplify octeon_irq_ciu_gpio_set_type.
- Octeon: Mark some functions __init in smp.c
- Octeon: Octeon: Add Octeon III CN7xxx interface detection
- PIC32: Add serial driver and bindings for it.
- PIC32: Add PIC32 deadman timer driver and bindings.
- PIC32: Add PIC32 clock timer driver and bindings.
- Pistachio: Determine SoC revision during boot
- Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
- Sibyte: Strip redundant comments from bcm1480_regs.h.
- Panic immediately if panic_on_oops is set.
- module: fix incorrect IS_ERR_VALUE macro usage.
- module: Make consistent use of pr_*
- Remove no longer needed work_on_cpu() call.
- Remove CONFIG_IPV6_PRIVACY from defconfigs.
- Fix registers of non-crashing CPUs in dumps.
- Handle MIPSisms in new vmcore_elf32_check_arch.
- Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
- Allow RIXI to be used on non-R2 or R6 cores.
- Reserve nosave data for hibernation
- Fix siginfo.h to use strict POSIX types.
- Don't unwind user mode with EVA.
- Fix watchpoint restoration
- Ptrace watchpoints for R6.
- Sync icache when it fills from dcache
- I6400 I-cache fills from dcache.
- Various MSA fixes.
- Cleanup MIPS_CPU_* definitions.
- Signal: Move generic copy_siginfo to signal.h
- Signal: Fix uapi include in exported asm/siginfo.h
- Timer fixes for sake of KVM.
- XPA TLB refill fixes.
- Treat perf counter feature
- Update John Crispin's email address
- Add PIC32 watchdog and bindings.
- Handle R10000 LL/SC bug in set_pte()
- cpufreq: Various fixes for Longson1.
- R6: Fix R2 emulation.
- mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
- ELF: ABI and FP fixes.
- Allow for relocatable kernel and use that to support KASLR.
- Fix CPC_BASE_ADDR mask
- Plenty fo smp-cps, CM, R6 and M6250 fixes.
- Make reset_control_ops const.
- Fix kernel command line handling of leading whitespace.
- Cleanups to cache handling.
- Add brcm, bcm6345-l1-intc device tree bindings.
- Use generic clkdev.h header
- Remove CLK_IS_ROOT usage.
- Misc small cleanups.
- CM: Fix compilation error when !MIPS_CM
- oprofile: Fix a preemption issue
- Detect DSP ASE v3 support:1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
MIPS: pic32mzda: fix getting timer clock rate.
MIPS: ath79: fix regression in PCI window initialization
MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
MIPS: Fix VZ probe gas errors with binutils <2.24
MIPS: perf: Fix I6400 event numbers
MIPS: DEC: Export `ioasic_ssr_lock' to modules
MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
MIPS: CM: Fix compilation error when !MIPS_CM
MIPS: Fix genvdso error on rebuild
USB: ohci-jz4740: Remove obsolete driver
MIPS: JZ4740: Probe OHCI platform device via DT
MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
MIPS: pistachio: Determine SoC revision during boot
MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
MIPS: Prevent "restoration" of MSA context in non-MSA kernels
MIPS: cevt-r4k: Dynamically calculate min_delta_ns
MIPS: malta-time: Take seconds into account
MIPS: malta-time: Start GIC count before syncing to RTC
MIPS: Force CPUs to lose FP context during mode switches
...
Stephen Boyd
Jan Kotas
Abel Vesa
Aisheng Dong
Matti Vaittinen
Linus Torvalds
Paul Cercueil
Jolly Shah
Daniel Mack
Gabriel Fernandez
Manivannan Sadhasivam
Mike Looijmans
Riku Voipio
Benjamin Gaignard
Sudeep Holla
Stephen Boyd
Joel Stanley
Chunyan Zhang
Elaine Zhang
Eugeniy Paltsev
Marek Vasut
Paul Burton
Linus Walleij
Tero Kristo
Daniel Lezcano
Akinobu Mita
Krzysztof Kozlowski
Masahiro Yamada
James Liao
Laxman Dewangan
Jean Delvare
Michael Turquette
Maxime Ripard
Wadim Egorov
Ezequiel Garcia