Replace usage of atomic_notifier_call_chain with
blocking_notifier_call_chain as the notifier function,
lineinfo_changed_notify, calls gpio_desc_to_lineinfo,
which calls pinctrl_gpio_can_use_line, which can sleep.
The chain isn't being called from an atomic context so the
the blocking notifier is a suitable substitute.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Move gpiolib-sysfs function declarations into their own header.
These functions are in gpiolib-sysfs.c, and are only required by gpiolib.c,
and so should be in a module header, not gpiolib.h.
This brings gpiolib-sysfs into line with gpiolib-cdev, and is another step
towards removing the sysfs inferface.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- use kobj_to_dev() in sysfs interface
- kerneldoc and documentation fixes
- relax the interrupt flags in gpio-mpc8xxx
- support new model in gpio-pca953x
- remove a redundant check from gpio-max732x
- support a new platform in gpio-zynq (+ some minor fixes)
- don't depend on GPIOLIB when already inside the "if GPIOLIB" in Kconfig
- support PM ops for suspend in gpio-omap
- minor tweaks in gpiolib
-----BEGIN PGP SIGNATURE-----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=TwKk
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.9-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.9
- use kobj_to_dev() in sysfs interface
- kerneldoc and documentation fixes
- relax the interrupt flags in gpio-mpc8xxx
- support new model in gpio-pca953x
- remove a redundant check from gpio-max732x
- support a new platform in gpio-zynq (+ some minor fixes)
- don't depend on GPIOLIB when already inside the "if GPIOLIB" in Kconfig
- support PM ops for suspend in gpio-omap
- minor tweaks in gpiolib
bitmap_full() is a shortcut to find_first_zero_bit().
Thus, no need to call it twice.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Split the cdev specific functionality out of gpiolib.c and into
gpiolib-cdev.c. This improves the readability and maintainability of both
the cdev and core gpiolib code.
Suggested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20200616093615.5167-1-warthog618@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- A new GPIO aggregator driver has been merged: this can
join a few select GPIO lines into a new aggregated GPIO
chip. This can be used for security: a process can be
granted access to only these lines, for example for
industrial control. Another way to use this is to
reexpose certain select lines to a virtual machine or
container.
- Warn if the gpio-line-names is too long in he DT parser
core.
- GPIO lines can now be looked up by line name in addition
to being looked up by offset.
New drivers:
- A new generic regmap GPIO driver has been merged. Too
many regmap drivers are starting to look like each other
so we need to create some common ground and try to move
drivers over to using that.
- The F7188X driver now supports F81865.
Driver improvements:
- Large improvements to the PCA953x expander, get multiple lines
and several cleanups.
- Large improvements to the DesignWare DWAPB driver, and Sergey
Semin has volunteered to maintain it.
- PL061 can now be built as a module, this is part of a bigger
effort to make the ARM platforms more modular.
-----BEGIN PGP SIGNATURE-----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=B5OK
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.8 kernel cycle.
Core changes:
- A new GPIO aggregator driver has been merged: this can join a few
select GPIO lines into a new aggregated GPIO chip. This can be used
for security: a process can be granted access to only these lines,
for example for industrial control. Another way to use this is to
reexpose certain select lines to a virtual machine or container.
- Warn if the gpio-line-names is too long in he DT parser core.
- GPIO lines can now be looked up by line name in addition to being
looked up by offset.
New drivers:
- A new generic regmap GPIO driver has been merged. Too many regmap
drivers are starting to look like each other so we need to create
some common ground and try to move drivers over to using that.
- The F7188X driver now supports F81865.
Driver improvements:
- Large improvements to the PCA953x expander, get multiple lines and
several cleanups.
- Large improvements to the DesignWare DWAPB driver, and Sergey Semin
has volunteered to maintain it.
- PL061 can now be built as a module, this is part of a bigger effort
to make the ARM platforms more modular"
* tag 'gpio-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: pca953x: Drop unneeded ACPI_PTR()
MAINTAINERS: Add gpio regmap section
gpio: add a reusable generic gpio_chip using regmap
gpiolib: Introduce gpiochip_irqchip_add_domain()
gpio: gpiolib: Allow GPIO IRQs to lazy disable
gpiolib: Separate GPIO_GET_LINEINFO_WATCH_IOCTL conditional
gpio: rcar: Fix runtime PM imbalance on error
gpio: pca935x: Allow IRQ support for driver built as a module
gpio: pxa: Add COMPILE_TEST support
dt-bindings: gpio: Add renesas,em-gio bindings
MAINTAINERS: Fix file name for DesignWare GPIO DT schema
gpio: dwapb: Remove unneeded has_irq member in struct dwapb_port_property
gpio: dwapb: Don't use IRQ 0 as valid Linux interrupt
gpio: dwapb: avoid error message for optional IRQ
gpio: dwapb: Call acpi_gpiochip_free_interrupts() on GPIO chip de-registration
gpio: max730x: bring gpiochip_add_data after port config
MAINTAINERS: Add GPIO Aggregator section
docs: gpio: Add GPIO Aggregator documentation
gpio: Add GPIO Aggregator
gpiolib: Add support for GPIO lookup by line name
...
The function connects an IRQ domain to a gpiochip and reuses
gpiochip_to_irq() which is provided by gpiolib.
gpiochip_irqchip_* and regmap_irq partially provide the same
functionality. This function will help to connect just the
minimal functionality of the gpiochip_irqchip which is needed to
work together with regmap-irq.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200528145845.31436-2-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We provided the right semantics on open drain lines being
by definition output but incidentally the irq set up function
would only allow IRQs on lines that were "not output".
Fix the semantics to allow output open drain lines to be used
for IRQs.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Russell King <linux@armlinux.org.uk>
Cc: stable@vger.kernel.org # v5.3+
Link: https://lore.kernel.org/r/20200527140758.162280-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With 'commit 461c1a7d47 ("gpiolib: override irq_enable/disable")' gpiolib
overrides irqchip's irq_enable and irq_disable callbacks. If irq_disable
callback is implemented then genirq takes unlazy path to disable irq.
Underlying irqchip may not want to implement irq_disable callback to lazy
disable irq when client drivers invokes disable_irq(). By overriding
irq_disable callback, gpiolib ends up always unlazy disabling IRQ.
Allow gpiolib to lazy disable IRQs by overriding irq_disable callback only
if irqchip implemented irq_disable. In cases where irq_disable is not
implemented irq_mask is overridden. Similarly override irq_enable callback
only if irqchip implemented irq_enable otherwise irq_unmask is overridden.
Fixes: 461c1a7d47 ("gpiolib: override irq_enable/disable")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/r/1590253873-11556-2-git-send-email-mkshah@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We already have two conditionals inside the outer one to check
if the command is GPIO_GET_LINEINFO_WATCH_IOCTL. I think it's
time to actually do what I have proposed in the first place, i.e.
to separate GPIO_GET_LINEINFO_WATCH_IOCTL from GPIO_GET_LINEINFO_IOCTL.
It's +13 LOCs, and surprisingly only +13 bytes of binary on x86_32,
but for the price of much better readability.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200525194028.74236-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently a GPIO lookup table can only refer to a specific GPIO by a
tuple, consisting of a GPIO controller label and a GPIO offset inside
the controller.
However, a GPIO may also carry a line name, defined by DT or ACPI.
If present, the line name is the most use-centric way to refer to a
GPIO. Hence add support for looking up GPIOs by line name.
Note that there is no guarantee that GPIO line names are globally
unique, so this will use the first match found.
Implement this by reusing the existing gpiod_lookup infrastructure.
Rename gpiod_lookup.chip_label to gpiod_lookup.key, to make it clear
that this field can have two meanings, and update the kerneldoc and
GPIO_LOOKUP*() macros.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Link: https://lore.kernel.org/r/20200511145257.22970-4-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- fix probing for chips without PWM in gpio-mvebu
- fix ida_simple_get() error path in gpio-exar
- fix user-space notifications for line state changes
-----BEGIN PGP SIGNATURE-----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=mll0
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v5.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into fixes
gpio fixes for v5.7-rc6
- fix probing for chips without PWM in gpio-mvebu
- fix ida_simple_get() error path in gpio-exar
- fix user-space notifications for line state changes
gpiochip_set_desc_names() no longer rejects GPIO line name collisions.
Hence GPIO line names are not guaranteed to be globally unique.
In case of multiple GPIO lines with the same name, gpio_name_to_desc()
will return the first match found.
Update the comments for gpio_name_to_desc() and
gpiochip_set_desc_names() to match reality.
Fixes: f881bab038 ("gpio: keep the GPIO line names internal")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200511101828.30046-1-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently we emit the REQUESTED line state event after the line is
requested but before the flags are configured. This is obviously wrong
as we want to pass the updated lineinfo to user-space together with the
event.
Since the flags can be configured in different ways depending on how the
line is being requested - we need to call the notifier chain in different
places separately.
Fixes: 51c1064e82 ("gpiolib: add new ioctl() for monitoring changes in line info")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The symbol 'gpio_of_notifier' doesn't exist without both CONFIG_OF_GPIO
and CONFIG_OF_DYNAMIC enabled, but is referenced when only
CONFIG_OF_DYNAMIC is enabled.
This broke building with 'make ARCH=um allyesconfig':
---------------
/usr/bin/ld: drivers/gpio/gpiolib.o: in function `gpiolib_dev_init':
./drivers/gpio/gpiolib.c:5293: undefined reference to `gpio_of_notifier'
collect2: error: ld returned 1 exit status
---------------
Fixes: 63636d956c ("gpio: of: Add DT overlay support for GPIO hogs")
Signed-off-by: David Gow <davidgow@google.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200425044655.166257-1-davidgow@google.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simplify the printing of kernel messages and make the messages more
accurate by using the most appropriate {dev,chip,gpiod}_*() helpers.
Sample impact:
-gpiochip_setup_dev: registered GPIOs 496 to 511 on device: gpiochip0 (e6050000.gpio)
+gpio gpiochip0: registered GPIOs 496 to 511 on e6050000.gpio
-no flags found for gpios
+gpio-953 (?): no flags found for gpios
-GPIO line 355 (PCIE/SATA switch) hogged as output/low
+gpio-355 (PCIE/SATA switch): hogged as output/low
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200424141432.11400-1-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We must not call pinctrl_gpio_can_use_line() with the gpio_lock taken
as it takes a mutex internally. Let's move the call before taking the
spinlock and store the return value.
This isn't perfect - there's a moment between calling
pinctrl_gpio_can_use_line() and taking the spinlock where the situation
can change but it isn't a regression either: previously this part wasn't
protected at all and it only affects the information user-space is
seeing.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: d2ac257982 ("gpiolib: provide a dedicated function for setting lineinfo")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This makes the new ioctl() a bit more robust - we now check if a line
is already being watched and return -EBUSY if the user-space tries to
start watching it again. Same for unwatch - return -EBUSY if user-space
tries to unwatch a line that's not being watched.
Fixes: 51c1064e82 ("gpiolib: add new ioctl() for monitoring changes in line info")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Core and userspace API:
- The userspace API KFIFOs have been imoproved with locks that
do not block interrupts. This makes us better at getting
events to userspace without blocking or disturbing new events
arriving in the same time. This was reviewed by the KFIFO
maintainer Stefani. This is a generic improvement which
paves the road for similar improvements in other subsystems.
- We provide a new ioctl() for monitoring changes in the line
information, such as when multiple clients are taking lines
and giving them back, possibly reconfiguring them in the
process: we can now monitor that and not get stuck with stale
static information.
- An example tool 'gpio-watch' is provided to showcase this
functionality.
- Timestamps for events are switched to ktime_get_ns() which is
monotonic. We previously had a 'realtime' stamp which could
move forward and *backward* in time, which probably would just
cause silent bugs and weird behaviour. In the long run we
see two relevant timestamps: ktime_get_ns() or the timestamp
sometimes provided by the GPIO hardware itself, if that
exists.
- Device Tree overlay support for GPIO hogs. On systems that
load overlays, these overlays can now contain hogs, and will
then be respected.
- Handle pin control interaction with nonexisting pin ranges
in the GPIO library core instead of in the individual
drivers.
New drivers:
- New driver for the Mellanox BlueField 2 GPIO controller.
Driver improvements:
- Introduce the BGPIOF_NO_SET_ON_INPUT flag to the generic
MMIO GPIO library and use this flag in the MT7621 driver.
- Texas Instruments OMAP CPU power management improvements,
such as blocking of idle on pending GPIO interrupts.
-----BEGIN PGP SIGNATURE-----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=EFm/
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO development for the v5.7 kernel cycle.
Core and userspace API:
- The userspace API KFIFOs have been imoproved with locks that do not
block interrupts. This makes us better at getting events to
userspace without blocking or disturbing new events arriving in the
same time. This was reviewed by the KFIFO maintainer Stefani. This
is a generic improvement which paves the road for similar
improvements in other subsystems.
- We provide a new ioctl() for monitoring changes in the line
information, such as when multiple clients are taking lines and
giving them back, possibly reconfiguring them in the process: we
can now monitor that and not get stuck with stale static
information.
- An example tool 'gpio-watch' is provided to showcase this
functionality.
- Timestamps for events are switched to ktime_get_ns() which is
monotonic. We previously had a 'realtime' stamp which could move
forward and *backward* in time, which probably would just cause
silent bugs and weird behaviour. In the long run we see two
relevant timestamps: ktime_get_ns() or the timestamp sometimes
provided by the GPIO hardware itself, if that exists.
- Device Tree overlay support for GPIO hogs. On systems that load
overlays, these overlays can now contain hogs, and will then be
respected.
- Handle pin control interaction with nonexisting pin ranges in the
GPIO library core instead of in the individual drivers.
New drivers:
- New driver for the Mellanox BlueField 2 GPIO controller.
Driver improvements:
- Introduce the BGPIOF_NO_SET_ON_INPUT flag to the generic MMIO GPIO
library and use this flag in the MT7621 driver.
- Texas Instruments OMAP CPU power management improvements, such as
blocking of idle on pending GPIO interrupts"
* tag 'gpio-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (59 commits)
Revert "gpio: eic-sprd: Use devm_platform_ioremap_resource()"
pinctrl: Unconditionally assign .request()/.free()
gpio: Unconditionally assign .request()/.free()
gpio: export of_pinctrl_get to modules
pinctrl: Define of_pinctrl_get() dummy for !PINCTRL
gpio: Rename variable in core APIs
gpio: Avoid using pin ranges with !PINCTRL
gpiolib: Remove unused gpio_chip parameter from gpio_set_bias()
gpiolib: Pass gpio_desc to gpio_set_config()
gpiolib: Introduce gpiod_set_config()
tools: gpio: Fix out-of-tree build regression
gpio: gpiolib: fix a doc warning
gpio: tegra186: Add Tegra194 pin ranges for GG.0 and GG.1
gpio: tegra186: Add support for pin ranges
gpio: Support GPIO controllers without pin-ranges
ARM: integrator: impd1: Use GPIO_LOOKUP() helper macro
gpio: brcmstb: support gpio-line-names property
tools: gpio: Fix typo in gpio-utils
tools: gpio-hammer: Apply scripts/Lindent and retain good changes
gpiolib: gpio_name_to_desc: factor out !name check
...
There are no core changes this time, only driver developments.
- New driver for the Dialog Semiconductor DA9062 Power Management
Integrated Circuit (PMIC).
- Renesas SH-PFC has improved consistency, with group and
register checks in the configuration checker.
- New subdriver for the Qualcomm IPQ6018.
- Add the RGMII pin control functionality to Qualcomm IPQ8064.
- Performance and code quality cleanups in the Mediatek
driver.
- Improve the Broadcom BCM2835 support to cover all the GPIOs
that exist in it.
- The Allwinner/Sunxi driver properly masks non-wakeup IRQs on
suspend.
- Add some missing groups and functions to the Ingenic driver.
- Convert some of the Freescale device tree bindings to use the
new and all improved JSON YAML markup.
- Refactorings and support for the SFIO/GPIO in the Tegra194
SoC driver.
- Support high impedance mode in the Spreadtrum/Unisoc driver.
-----BEGIN PGP SIGNATURE-----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=1ZKq
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.7 kernel cycle.
There are no core changes this time, only driver developments:
- New driver for the Dialog Semiconductor DA9062 Power Management
Integrated Circuit (PMIC).
- Renesas SH-PFC has improved consistency, with group and register
checks in the configuration checker.
- New subdriver for the Qualcomm IPQ6018.
- Add the RGMII pin control functionality to Qualcomm IPQ8064.
- Performance and code quality cleanups in the Mediatek driver.
- Improve the Broadcom BCM2835 support to cover all the GPIOs that
exist in it.
- The Allwinner/Sunxi driver properly masks non-wakeup IRQs on
suspend.
- Add some missing groups and functions to the Ingenic driver.
- Convert some of the Freescale device tree bindings to use the new
and all improved JSON YAML markup.
- Refactorings and support for the SFIO/GPIO in the Tegra194 SoC
driver.
- Support high impedance mode in the Spreadtrum/Unisoc driver"
* tag 'pinctrl-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (64 commits)
pinctrl: qcom: fix compilation error
pinctrl: qcom: use scm_call to route GPIO irq to Apps
pinctrl: sprd: Add pin high impedance mode support
pinctrl: sprd: Use the correct pin output configuration
pinctrl: tegra: Add SFIO/GPIO programming on Tegra194
pinctrl: tegra: Renumber the GG.0 and GG.1 pins
pinctrl: tegra: Do not add default pin range on Tegra194
pinctrl: tegra: Pass struct tegra_pmx for pin range check
pinctrl: tegra: Fix "Scmitt" -> "Schmitt" typo
pinctrl: tegra: Fix whitespace issues for improved readability
pinctrl: mediatek: Use scnprintf() for avoiding potential buffer overflow
pinctrl: freescale: drop the dependency on ARM64 for i.MX8M
Revert "pinctrl: mvebu: armada-37xx: use use platform api"
dt-bindings: pinctrl: at91: Fix a typo ("descibe")
pinctrl: meson: add tsin pinctrl for meson gxbb/gxl/gxm
pinctrl: sprd: Fix the kconfig warning
pinctrl: ingenic: add hdmi-ddc pin control group
pinctrl: sirf/atlas7: Replace zero-length array with flexible-array member
pinctrl: sprd: Allow the SPRD pinctrl driver building into a module
pinctrl: Export some needed symbols at module load time
...
There is struct gpio *gc, *chip and *gpiochip, and yes
I am responsible for some of the inconsistencies. I want
this to be just gc everywhere for minimizing cognitive
resistance when reading the code: more compact function
signatures and less clutter.
Purely syntactic changes intended. No semantic effects.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200329140405.52276-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Do not use the struct gpio_device's .pin_ranges field if the PINCTRL
Kconfig symbol is not selected to avoid build failures.
Fixes: 2ab73c6d83 ("gpio: Support GPIO controllers without pin-ranges")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200330090257.2332864-1-thierry.reding@gmail.com
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All callers of gpio_set_config() have to convert a gpio_desc to a
gpio_chip and offset. Avoid these duplicated conversion steps by
letting gpio_set_config() take a gpio_desc pointer directly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200325100439.14000-2-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO Aggregator will need a method to forward a .set_config() call
to its parent gpiochip. This requires obtaining the gpio_chip and
offset for a given gpio_desc. While gpiod_to_chip() is public,
gpio_chip_hwgpio() is not, so there is currently no method to obtain the
needed GPIO offset parameter.
Hence introduce a public gpiod_set_config() helper, which invokes the
.set_config() callback through a gpio_desc pointer, like is done for
most other gpio_chip callbacks.
Rewrite the existing gpiod_set_debounce() helper as a wrapper around
gpiod_set_config(), to avoid duplication.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200324135653.6676-5-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use a different markup for the ERR_PTR, as %FOO doesn't work
if there are parenthesis. So, use, instead:
``ERR_PTR(-EINVAL)``
This fixes the following warning:
./drivers/gpio/gpiolib.c:139: WARNING: Inline literal start-string without end-string.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/51197e3568f073e22c280f0584bfa20b44436708.1584456635.git.mchehab+huawei@kernel.org
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Wake gpiochip_generic_request() call into the pinctrl helpers only if a
GPIO controller had any pin-ranges assigned to it. This allows a driver
to unconditionally use this helper if it supports multiple devices of
which only a subset have pin-ranges assigned to them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200319122737.3063291-2-thierry.reding@gmail.com
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since name == NULL can't ever match, move the check out of
IRQ-disabled region.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
These two devres functions devm_gpiochip_[add|remove]()
were in the wrong file. They should be in gpiolib-devres.c
not gpiolib.c.
Link: https://lore.kernel.org/r/20200313081522.35143-1-linus.walleij@linaro.org
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The implementation if .irq_disable() which kicks in between
the gpiolib and the driver is not properly mimicking the
expected semantics of the irqchip core: the irqchip will
call .irq_disable() if that exists, else it will call
mask_irq() which first checks if .irq_mask() is defined
before calling it.
Since we are calling it unconditionally, we get this bug
from drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c, as it only
defines .irq_mask_ack and not .irq_mask:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = (ptrval)
(...)
PC is at 0x0
LR is at gpiochip_irq_disable+0x20/0x30
Fix this by only calling .irq_mask() if it exists.
Cc: Brian Masney <masneyb@onstation.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Fixes: 461c1a7d47 ("gpiolib: override irq_enable/disable")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200306132326.1329640-1-linus.walleij@linaro.org
- replace z zero-length array with flexible-array member in gpio-uniphier
- make naming of variables consistent in uapi line event code
- fix the behavior of line watch/unwatch ioctl()
-----BEGIN PGP SIGNATURE-----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=ASHn
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.7-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.7 part 2
- replace z zero-length array with flexible-array member in gpio-uniphier
- make naming of variables consistent in uapi line event code
- fix the behavior of line watch/unwatch ioctl()
The optimization to check for requested lines actually optimized for the
uncomon error case, where one of the GPIO lines is still in use.
Hence the error message must be printed when the loop is terminated
early, not when it went through all available GPIO lines.
Fixes: 869233f813 ("gpiolib: Optimize gpiochip_remove() when check for requested line")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200302082448.11795-1-geert+renesas@glider.be
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When operating on the bits of watched_lines bitmap, we're using
desc_to_gpio() which returns the GPIO number from the global numberspace.
This leads to all sorts of memory corruptions and invalid behavior. We
should switch to using gpio_chip_hwgpio() instead.
Fixes: 51c1064e82 ("gpiolib: add new ioctl() for monitoring changes in line info")
Reported-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Kent Gibson <warthog618@gmail.com>
Fix the field having a bit cleared by the unwatch ioctl().
Fixes: 51c1064e82 ("gpiolib: add new ioctl() for monitoring changes in line info")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Rename 'event' to 'ge' to be consistent with other use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Here are the following optimizations have been done:
- break the loop after first found requested line
- due to above, drop redundant boolean variable
- replace open coded variant of gpiochip_is_requested()
- due to above, drop redundant pointer to struct gpio_desc
- use 'unsigned int' instead of 'unsigned' for loop counter
Note, pointer to struct gpio_chip followed by pointer to struct gpio_device
is still valid, back link is not.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200225114725.839-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function was currently used internal by the gpiolib. Since commit
56cc3af4e8 ("pinctrl: da9062: add driver support") it is also used by
drivers so we need to export the symbol.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20200225093102.10964-1-m.felsch@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As GPIO hogs are configured at GPIO controller initialization time,
adding/removing GPIO hogs in DT overlays does not work.
Add support for GPIO hogs described in DT overlays by registering an OF
reconfiguration notifier, to handle the addition and removal of GPIO hog
subnodes to/from a GPIO controller device node.
Note that when a GPIO hog device node is being removed, its "gpios"
properties is no longer available, so we have to keep track of which
node a hog belongs to, which is done by adding a pointer to the hog's
device node to struct gpio_desc.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200220130149.26283-3-geert+renesas@glider.be
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The existing use of ktime_get_real_ns() in the timestamps from
the GPIO events is dubious.
We have had several discussions about this timestamp, and it is
unclear whether userspace has ever taken into account that a
timestamp from ktime_get_real_ns() can actually move backwards
in time relative the previous timetamp, and userspace is more
likely to expect a monotonic counter.
Background:
https://lore.kernel.org/linux-gpio/CAK8P3a1Skvm48sje8FNDPLYqyz9Lf8q0qX1QETWtyZTxuX4k1g@mail.gmail.com/https://marc.info/?l=linux-gpio&m=151661955709074&w=2
The change is ABI incompatible, but incompatible in a way that
is IMO more likely to fix future bugs rather than break current
userspace. To the best of my knowledge all userspace expects
a monotonic timestamp and users are just lucky that they very
seldom move backwards in time.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Whenever retrieving a descriptor from a gpiochip: use the provided
helper which checks for errors.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200219094702.6463-1-brgl@bgdev.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently there is no way for user-space to be informed about changes
in status of GPIO lines e.g. when someone else requests the line or its
config changes. We can only periodically re-read the line-info. This
is fine for simple one-off user-space tools, but any daemon that provides
a centralized access to GPIO chips would benefit hugely from an event
driven line info synchronization.
This patch adds a new ioctl() that allows user-space processes to reuse
the file descriptor associated with the character device for watching
any changes in line properties. Every such event contains the updated
line information.
Currently the events are generated on three types of status changes: when
a line is requested, when it's released and when its config is changed.
The first two are self-explanatory. For the third one: this will only
happen when another user-space process calls the new SET_CONFIG ioctl()
as any changes that can happen from within the kernel (i.e.
set_transitory() or set_debounce()) are of no interest to user-space.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
We'll soon be filling out the gpioline_info structure in multiple
places. Add a separate function that given a gpio_desc sets all relevant
fields.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Currently if the line-event kfifo is full, we just silently drop any new
events. Add a ratelimited debug message so that we at least have some
trace in the kernel log of event overflow.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The read_lock mutex is supposed to prevent collisions between reading
and writing to the line event kfifo but it's actually only taken when
the events are being read from it.
Drop the mutex entirely and reuse the spinlock made available to us in
the waitqueue struct. Take the lock whenever the fifo is modified or
inspected. Drop the call to kfifo_to_user() and instead first extract
the new element from kfifo when the lock is taken and only then pass
it on to the user after the spinlock is released.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Remove unnecessary argument when setting PIN_CONFIG_BIAS_DISABLE. No
argument is expected by pinctrl, so removing it should be harmless.
Fixes: 2148ad7790 ("gpiolib: add support for disabling line bias")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Commit d90f36851d ("gpiolib: have a single place of calling
set_config()") introduced a regression where we don't pass the right
variable as argument to the set_config() callback of gpio driver from
gpio_set_config(). After reverting two additional patches that came
on top of it - this addresses the issue by changing the type of the last
argument of gpio_do_set_config() to unsigned long and making sure the
packed config variable is actually used in gpio_set_config().
Fixes: d90f36851d ("gpiolib: have a single place of calling set_config()")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
This reverts commit e5e42ad224.
This patch came on top of another patch that introduced a regression.
Revert it before addressing the culprit.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Kent Gibson
Linus Walleij
Andy Shevchenko
Linus Torvalds
Michael Walle
Maulik Shah
Geert Uytterhoeven
Bartosz Golaszewski
David Gow
Thierry Reding
Mauro Carvalho Chehab
Michał Mirosław
Marco Felsch