Add a new RPROC_DETACHED state to take into account scenarios
where the remoteproc core needs to attach to a remote processor
that is booted by another entity.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-2-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On secure devices there exists a race condition which could lock the MSS
CONFIG AHB bus thus preventing access to BOOT_STATUS register during SSR.
Switch to polling the MSS_STATUS register with an additional 10 us delay
to reliably track boot completion.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200716120514.21588-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On platforms with 32-bit phys_addr_t the shift to get the upper word of
the base address of the memory region is invalid. Cast the base to 64
bit to resolv this.
Fixes: 549b67da66 ("remoteproc: qcom: Introduce helper to store pil info in IMEM")
Tested-by: Nathan Chancellor <natechancellor@gmail.com> # build
Reported-by: Lee Jones <lee.jones@linaro.org>
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20200716054817.157608-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Looks as though 'name' has now been moved into 'struct sysmod_event'
which is passed in instead. However, the parameter descriptions were
not updated at the same time. Let's do that now.
Fixes the following W=1 kernel build warning(s):
drivers/remoteproc/qcom_sysmon.c:78: warning: Function parameter or member 'event' not described in 'sysmon_send_event'
drivers/remoteproc/qcom_sysmon.c:78: warning: Excess function parameter 'name' description in 'sysmon_send_event'
drivers/remoteproc/qcom_sysmon.c:350: warning: Function parameter or member 'event' not described in 'ssctl_send_event'
drivers/remoteproc/qcom_sysmon.c:350: warning: Excess function parameter 'name' description in 'ssctl_send_event'
Cc: Andy Gross <agross@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200715123551.4011154-2-lee.jones@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes the following W=1 kernel build warning(s):
drivers/remoteproc/remoteproc_core.c: In function ‘rproc_find_carveout_by_name’:
drivers/remoteproc/remoteproc_core.c:257:2: warning: function ‘rproc_find_carveout_by_name’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
257 | vsnprintf(_name, sizeof(_name), name, args);
| ^~~~~~~~~
drivers/remoteproc/remoteproc_core.c: In function ‘rproc_mem_entry_init’:
drivers/remoteproc/remoteproc_core.c:993:2: warning: function ‘rproc_mem_entry_init’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
993 | vsnprintf(mem->name, sizeof(mem->name), name, args);
| ^~~~~~~~~
drivers/remoteproc/remoteproc_core.c: In function ‘rproc_of_resm_mem_entry_init’:
drivers/remoteproc/remoteproc_core.c:1029:2: warning: function ‘rproc_of_resm_mem_entry_init’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
1029 | vsnprintf(mem->name, sizeof(mem->name), name, args);
| ^~~~~~~~~
Cc: Brian Swetland <swetland@google.com>
Cc: Mark Grosen <mgrosen@ti.com>
Cc: Guzman Lugo <fernando.lugo@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Cc: Robert Tivy <rtivy@ti.com>
Cc: De Leon <x0095078@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200715123551.4011154-1-lee.jones@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
drivers/remoteproc/qcom_common.c: In function 'qcom_ssr_get_subsys':
drivers/remoteproc/qcom_common.c:210:9: error: implicit declaration of function 'kzalloc'; did you mean 'vzalloc'?
[-Werror=implicit-function-declaration]
info = kzalloc(sizeof(*info), GFP_KERNEL);
^~~~~~~
vzalloc
kzalloc() is declared in linux/slab.h, add include to fix build issue.
Tested-by: Alex Elder <elder@linaro.org>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Link: https://lore.kernel.org/r/20200713020003.134039-1-wangkefeng.wang@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The SSR subdevice only adds callback for the unprepare event. Add callbacks
for prepare, start and prepare events. The client driver for a particular
remoteproc might be interested in knowing the status of the remoteproc
while undergoing SSR, not just when the remoteproc has finished shutting
down.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/1592965408-16908-3-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently there is a single notification chain which is called whenever any
remoteproc shuts down. This leads to all the listeners being notified, and
is not an optimal design as kernel drivers might only be interested in
listening to notifications from a particular remoteproc. Create a global
list of remoteproc notification info data structures. This will hold the
name and notifier_list information for a particular remoteproc. The API
to register for notifications will use name argument to retrieve the
notification info data structure and the notifier block will be added to
that data structure's notification chain. Also move from blocking notifier
to srcu notifer based implementation to support dynamic notifier head
creation.
Reviewed-by: Alex Elder <elder@linaro.org>
Co-developed-by: Siddharth Gupta <sidgup@codeaurora.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/1592965408-16908-2-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Update the PIL relocation information in IMEM with information about
where the firmware for various remoteprocs are loaded.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200622191942.255460-4-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A region in IMEM is used to communicate load addresses of remoteproc to
post mortem debug tools. Implement a helper function that can be used to
store this information in order to enable these tools to process
collected ramdumps.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200622191942.255460-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This reverts commit a99a37f6cd.
Removing PM runtime operations from the remoteproc core in order to:
1) Keep all power management operations in platform drivers. That way we
do not loose flexibility in an area that is very HW specific.
2) Avoid making the support for remote processor managed by external
entities more complex that it already is.
3) Fix regression introduced for the Omap remoteproc driver.
Acked-by: Suman Anna <s-anna@ti.com>
Tested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200630163118.3830422-3-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The header file linux/uio.h includes crypto/hash.h which pulls in
most of the Crypto API. Since linux/uio.h is used throughout the
kernel this means that every tiny bit of change to the Crypto API
causes the entire kernel to get rebuilt.
This patch fixes this by moving it into lib/iov_iter.c instead
where it is actually used.
This patch also fixes the ifdef to use CRYPTO_HASH instead of just
CRYPTO which does not guarantee the existence of ahash.
Unfortunately a number of drivers were relying on linux/uio.h to
provide access to linux/slab.h. This patch adds inclusions of
linux/slab.h as detected by build failures.
Also skbuff.h was relying on this to provide a declaration for
ahash_request. This patch adds a forward declaration instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This introduces device managed versions of functions used to register
remoteproc devices, add support for remoteproc driver specific resource
control, enables remoteproc drivers to specify ELF class and machine for
coredumps. It integrates pm_runtime in the core for keeping resources
active while the remote is booted and holds a wake source while
recoverying a remote processor after a firmware crash.
It refactors the remoteproc device's allocation path to simplify the
logic, fix a few cleanup bugs and to not clone const strings onto the
heap. Debugfs code is simplifies using the DEFINE_SHOW_ATTRIBUTE and a
zero-length array is replaced with flexible-array.
A new remoteproc driver for the JZ47xx VPU is introduced, the Qualcomm
SM8250 gains support for audio, compute and sensor remoteprocs and the
Qualcomm SC7180 modem support is cleaned up and improved.
The Qualcomm glink subsystem-restart driver is merged into the main
glink driver, the Qualcomm sysmon driver is extended to properly notify
remote processors about all other remote processors' state transitions.
-----BEGIN PGP SIGNATURE-----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=4k54
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This introduces device managed versions of functions used to register
remoteproc devices, add support for remoteproc driver specific
resource control, enables remoteproc drivers to specify ELF class and
machine for coredumps. It integrates pm_runtime in the core for
keeping resources active while the remote is booted and holds a wake
source while recoverying a remote processor after a firmware crash.
It refactors the remoteproc device's allocation path to simplify the
logic, fix a few cleanup bugs and to not clone const strings onto the
heap. Debugfs code is simplifies using the DEFINE_SHOW_ATTRIBUTE and a
zero-length array is replaced with flexible-array.
A new remoteproc driver for the JZ47xx VPU is introduced, the Qualcomm
SM8250 gains support for audio, compute and sensor remoteprocs and the
Qualcomm SC7180 modem support is cleaned up and improved.
The Qualcomm glink subsystem-restart driver is merged into the main
glink driver, the Qualcomm sysmon driver is extended to properly
notify remote processors about all other remote processors' state
transitions"
* tag 'rproc-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc: (43 commits)
remoteproc: Fix an error code in devm_rproc_alloc()
MAINTAINERS: Add myself as reviewer for Ingenic rproc driver
remoteproc: ingenic: Added remoteproc driver
remoteproc: Add support for runtime PM
dt-bindings: Document JZ47xx VPU auxiliary processor
remoteproc: wcss: Fix arguments passed to qcom_add_glink_subdev()
remoteproc: Fix and restore the parenting hierarchy for vdev
remoteproc: Fall back to using parent memory pool if no dedicated available
remoteproc: Replace zero-length array with flexible-array
remoteproc: wcss: add support for rpmsg communication
remoteproc: core: Prevent system suspend during remoteproc recovery
remoteproc: qcom_q6v5_mss: Remove unused q6v5_da_to_va function
remoteproc: qcom_q6v5_mss: map/unmap mpss segments before/after use
remoteproc: qcom_q6v5_mss: Drop accesses to MPSS PERPH register space
dt-bindings: remoteproc: qcom: Replace halt-nav with spare-regs
remoteproc: qcom: pas: Add SM8250 PAS remoteprocs
dt-bindings: remoteproc: qcom: pas: Add SM8250 remoteprocs
remoteproc: qcom_q6v5_mss: Extract mba/mpss from memory-region
dt-bindings: remoteproc: qcom: Use memory-region to reference memory
remoteproc: qcom: pas: Add SC7180 Modem support
...
The comments say that this function should return NULL on error and the
caller expects NULL returns as well so I have modified the code to match.
Returning an ERR_PTR(-ENOMEM) would lead to an OOps.
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 305ac5a766 ("remoteproc: Add device-managed variants of rproc_alloc/rproc_add")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200520120705.GH172354@mwanda
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This driver is used to boot, communicate with and load firmwares to the
MIPS co-processor found in the VPU hardware of the JZ47xx SoCs from
Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200515104340.10473-4-paul@crapouillou.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Call pm_runtime_get_sync() before the firmware is loaded, and
pm_runtime_put() after the remote processor has been stopped.
Even though the remoteproc device has no PM callbacks, this allows the
parent device's PM callbacks to be properly called.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200515104340.10473-3-paul@crapouillou.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Recently qcom_add_glink_subdev() was extended to also take the glink_ssr
identifier as an argument and I missed this while applying '8a226e2c71bb
("remoteproc: wcss: add support for rpmsg communication")'.
Fixes: 8a226e2c71 ("remoteproc: wcss: add support for rpmsg communication")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200514185856.1598945-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The commit 086d08725d ("remoteproc: create vdev subdevice with specific
dma memory pool") has introduced a new vdev subdevice for each vdev
declared in the firmware resource table and made it as the parent for the
created virtio rpmsg devices instead of the previous remoteproc device.
This changed the overall parenting hierarchy for the rpmsg devices, which
were children of virtio devices, and does not allow the corresponding
rpmsg drivers to retrieve the parent rproc device through the
rproc_get_by_child() API.
Fix this by restoring the remoteproc device as the parent. The new vdev
subdevice can continue to inherit the DMA attributes from the remoteproc's
parent device (actual platform device).
Cc: stable@vger.kernel.org
Fixes: 086d08725d ("remoteproc: create vdev subdevice with specific dma memory pool")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200420160600.10467-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In some cases, like with OMAP remoteproc, we are not creating dedicated
memory pool for the virtio device. Instead, we use the same memory pool
for all shared memories. The current virtio memory pool handling forces
a split between these two, as a separate device is created for it,
causing memory to be allocated from bad location if the dedicated pool
is not available. Fix this by falling back to using the parent device
memory pool if dedicated is not available.
Cc: stable@vger.kernel.org
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Fixes: 086d08725d ("remoteproc: create vdev subdevice with specific dma memory pool")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200420160600.10467-2-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The system might go into suspend during recovery of any remoteproc.
This will interrupt the recovery process in between increasing the
recovery time. Make the platform device as wakeup capable and
use pm_stay_wake/pm_relax APIs to avoid system from going into
suspend during recovery.
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/1588183482-21146-1-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Remove unsed q6v5_da_to_va function as the mss driver uses a per segment
dump function.
Tested-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200415071619.6052-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The application processor accessing the mpss region when the Q6 modem is
running will lead to an XPU violation. Fix this by un-mapping the mpss
segments post copy during mpss authentication and coredumps.
Tested-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200415071619.6052-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
7C retail devices using MSA based boot will result in a fuse combination
which will prevent accesses to MSS PERPH register space where the mpss
clocks and halt-nav reside. So drop all accesses to the MPSS PERPH
register space. Issuing HALT NAV request and turning on the mss clocks
as part of SSR will no longer be required since the modem firmware will
have the necessary fixes to ensure that there are no pending NAV DMA
transactions.
Tested-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200415145110.20624-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In the absence of mba and mpss sub-child extract the mba/mpss regions
from the memory-region property.
Tested-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200421143228.8981-5-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for booting the Modem DSP found on Qualcomm's SC7180 SoCs.
Tested-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200421143228.8981-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
sizeof() when applied to a pointer typed expression gives the
size of the pointer, not that of the pointed data.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Fixes: 63c13d61ea ("remoteproc/mediatek: add SCP support for mt8183")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200509084237.36293-1-weiyongjun1@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Rather than carrying a special purpose blocking notifier for glink_ssr
in remoteproc's qcom_common.c, move it into glink_ssr so allow wider
reuse of the common one.
The rpmsg glink header file is used in preparation for the next patch.
Acked-by: Chris Lew <clew@codeaurora.org>
Acked-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20200423003736.2027371-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Pass ssr_name to glink subdevice in preparation for tying glink_ssr to
the glink subdevice, rather than having its own "ssr subdevice".
Acked-by: Chris Lew <clew@codeaurora.org>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20200423003736.2027371-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This fixes a regression in the probe error path of the Qualcomm modem
remoteproc driver and a mix up of phy_addr_t and dma_addr_t in the
Mediatek SCP control driver.
-----BEGIN PGP SIGNATURE-----
iQJPBAABCAA5FiEEBd4DzF816k8JZtUlCx85Pw2ZrcUFAl6gzV4bHGJqb3JuLmFu
ZGVyc3NvbkBsaW5hcm8ub3JnAAoJEAsfOT8Nma3FsjwQAIuUG1XqHoHxLoXubIEU
wRK0cKbbE87GaGgsnHtnt/oqlXCY6mkPN5Z9ADBPA3bRxSg/jUiqC2DaIzVrbFPX
x/a5UUr+N9B76+8QXCEg5w+HbJFM9HAMNT7IOXRddivBwduxgGzdfIiWZOouFKTV
yRYlThb1iUiSWSMi0tGTXM4SQXNFs6HrTBh4Xt+Z3bRDp39esmPXbIennwkXn+9d
A2Z9UrjOWLh7X80Iu0kvd3nQcQjMvESd6rG0bbuA7B126/htuL0VVFW93JEOs2yn
xtuoinMKto+pXBzhdUOXXOs85aFLQ1DW48H3tEfjfJsnAG/iJe/EB9j3H64Fdj8f
YgZvaveGzjuP7+5V1CnsLKbdIf/QhIQlKXAXE+8BN3kjQXEek4+otEM2cLZCh8bI
2FNVVmDwV/UqmVb5Xg5LTz+QbL+IsjjiOojXAjOBT7scVBDygutku2vFEVc84nTt
OJeYQ+UVon8SraM3qZqgjUKkle9Nwu9YjsotR7tvO9VSmAyAzqLDetotPVzBo3UQ
CvGKoqBrYYdm2Wz1G6QT70d74DdgNYwXK6K/NZg+Cresl0g5X54fCdfZBxnwtgmF
hgIPexeYAbwm4Z8vdcKtxPhxMEVivBFgbVujNIdOdo8JDgpx6EmFozJ7EopAziN2
NlzSYuuNigToV3MFxf+ubFco
=WDtr
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc fixes from Bjorn Andersson:
"This fixes a regression in the probe error path of the Qualcomm modem
remoteproc driver and a mix up of phy_addr_t and dma_addr_t in the
Mediatek SCP control driver"
* tag 'rproc-v5.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
remoteproc: mtk_scp: use dma_addr_t for DMA API
remoteproc: qcom_q6v5_mss: fix q6v5_probe() error paths
remoteproc: qcom_q6v5_mss: fix a bug in q6v5_probe()
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.
Fixes: 791c13b709 ("remoteproc: Fix NULL pointer dereference in rproc_virtio_notify")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200411160750.32573-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On some SoC architecture, it is needed to enable HW like
clock, bus, regulator, memory region... before loading
co-processor firmware.
This patch introduces prepare and unprepare ops to execute
platform specific function before firmware loading and after
stop execution.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200417002036.24359-2-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Since checks are present in the remoteproc elf loader before calling
da_to_va, loading a elf64 will work on 32bits flavors of kernel.
Indeed, if a segment size is larger than what size_t can hold, the
loader will return an error so the functionality is equivalent to
what exists today.
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20200422093017.10985-1-cleger@kalray.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add API functions devm_rproc_alloc() and devm_rproc_add(), which behave
like rproc_alloc() and rproc_add() respectively, but register their
respective cleanup function to be called on driver detach.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200417170040.174319-2-paul@crapouillou.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The current name field used in the remoteproc structure is simply
a pointer to a name field supplied during the rproc_alloc() call.
The pointer passed in by remoteproc drivers during registration is
typically a dev_name pointer, but it is possible that the pointer
will no longer remain valid if the devices themselves were created
at runtime like in the case of of_platform_populate(), and were
deleted upon any failures within the respective remoteproc driver
probe function.
So, allocate and maintain a local copy for this name field to
keep it agnostic of the logic used in the remoteproc drivers.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200417002036.24359-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Get rid of tedious error management by moving firmware and operation
allocation after calling device_initialize(). That way we take advantage
of the automatic call to rproc_type_release() to cleanup after ourselves
when put_device() is called.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200420231601.16781-5-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Make the rproc_ops allocation a function on its own in an effort
to clean up function rproc_alloc().
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200420231601.16781-4-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Improve the readability of function rproc_alloc_firmware() by using
a non-negated condition and moving the comment out of the conditional
block
Suggested-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200420231601.16781-3-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
For cases where @firmware is declared "const char *", use function
kstrdup_const() to avoid needlessly creating another copy on the
heap.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200420231601.16781-2-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Clients/services running on a remoteproc that booted up might need to be
aware of the state of already running remoteprocs. When a remoteproc boots
up (fresh or after recovery) it is not aware of the remoteprocs that booted
before it, i.e., the system state is incomplete. So to keep track of it we
send sysmon on behalf of all 'ONLINE' remoteprocs.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1586389003-26675-4-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add notification for other stages of remoteproc boot and shutdown. This
includes adding callback functions for the prepare and unprepare events,
and fleshing out the callback function for start.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1586389003-26675-3-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Current implementation of the sysmon driver does not support adding
notifications for other remoteproc events - prepare, start, unprepare.
Clients on the remoteproc side might be interested in knowing when a
remoteproc boots up. This change adds the ability to send the notification
type along with the name. For example, audio DSP is interested in knowing
when modem has crashed so that it can perform cleanup and wait for modem to
boot up before it starts processing data again.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1586389003-26675-2-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Modify drivers which are using remoteproc coredump functionality to use
rproc_coredump_set_elf_info in order to create correct elf coredump
format.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20200410102433.2672-3-cleger@kalray.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In an effort to cleanup firmware name allocation, replace the
cumbersome mechanic used to allocate a default firmware name with
function kasprintf().
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200415204858.2448-4-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Make the firmware name allocation a function on its own in an
effort to cleanup function rproc_alloc().
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200415204858.2448-3-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If ida_simple_get() returns an error when called in rproc_alloc(),
put_device() is called to clean things up. By this time the rproc
device type has been assigned, with rproc_type_release() as the
release function.
The first thing rproc_type_release() does is call:
idr_destroy(&rproc->notifyids);
But at the time the ida_simple_get() call is made, the notifyids
field in the remoteproc structure has not been initialized.
I'm not actually sure this case causes an observable problem, but
it's incorrect. Fix this by initializing the notifyids field before
calling ida_simple_get() in rproc_alloc().
Fixes: b5ab5e24e9 ("remoteproc: maintain a generic child device for each rproc")
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200415204858.2448-2-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In preparation to virtio header changes, include slab.h directly as
this module is using it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
dma_addr_t and phys_addr_t are distinct types and must not be
mixed, as both the values and the size of the type may be
different depending on what the remote device uses.
In this driver the compiler warns when the two types are different:
drivers/remoteproc/mtk_scp.c: In function 'scp_map_memory_region':
drivers/remoteproc/mtk_scp.c:454:9: error: passing argument 3 of 'dma_alloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]
454 | &scp->phys_addr, GFP_KERNEL);
| ^~~~~~~~~~~~~~~
| |
| phys_addr_t * {aka unsigned int *}
In file included from drivers/remoteproc/mtk_scp.c:7:
include/linux/dma-mapping.h:642:15: note: expected 'dma_addr_t *' {aka 'long long unsigned int *'} but argument is of type 'phys_addr_t *' {aka 'unsigned int *'}
642 | dma_addr_t *dma_handle, gfp_t gfp)
Change the phys_addr member to be typed and named according
to how it is allocated.
Fixes: 63c13d61ea ("remoteproc/mediatek: add SCP support for mt8183")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200408155450.2186471-1-arnd@arndb.de
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If an error occurs in q6v5_probe() after the proxy power domains
are attached, but before qcom_add_ipa_notify_subdev() is called,
qcom_remove_ipa_notify_subdev() is called in the error path, which
is a bug. Fix this by having that call be reached through a
different label.
Additionally, if qcom_add_sysmon_subdev() returns an error, the
subdevs that had already been added will not be properly removed.
Fix this by having the added subdevs (including the IPA notify one)
be removed in this case.
Finally, arrange for the sysmon subdev to be removed before the rest
in the event rproc_add() returns an error.
Have cleanup activity done in q6v5_remove() be done in the reverse
order they are set up in q6v5_probe() (the same order they're done
in the q6v5_probe() error path). Use a local variable for the
remoteproc pointer, which is used repeatedly.
Remove errant semicolons at the end of two function blocks.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20200403175005.17130-4-elder@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If looking up the DT "firmware-name" property fails in q6v6_probe(),
the function returns without freeing the remoteproc structure
that has been allocated. Fix this by jumping to the free_rproc
label, which takes care of this.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20200403175005.17130-3-elder@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When building arm allyesconfig:
drivers/remoteproc/omap_remoteproc.c:174:44: error: too many arguments
to function call, expected 2, have 3
timer->timer_ops->set_load(timer->odt, 0, 0);
~~~~~~~~~~~~~~~~~~~~~~~~~~ ^
1 error generated.
This is due to commit 02e6d546e3 ("clocksource/drivers/timer-ti-dm:
Enable autoreload in set_pwm") in the clockevents tree interacting with
commit e28edc5719 ("remoteproc/omap: Request a timer(s) for remoteproc
usage") from the rpmsg tree.
This should have been fixed during the merge of the remoteproc tree
since it happened after the clockevents tree merge; however, it does not
look like my email was noticed by either maintainer and I did not pay
attention when the pull was sent since I was on CC.
Fixes: c657011431 ("Merge tag 'rproc-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc")
Link: https://lore.kernel.org/lkml/20200327185055.GA22438@ubuntu-m2-xlarge-x86/
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This introduces a range of improvements to the OMAP remoeteproc driver;
among other things adding devicetree, suspend/resume and watchdog
support, and adds support the remoteprocs in the DRA7xx SoC.
It introduces support for 64-bit firmware, extends the ELF loader to
support this and fixes for a number of race conditions in the recovery
handling.
It introduces a generic mechanism to allow remoteproc drivers to sync
state with remote processors during a panic, and uses this to prepare
Qualcomm remote processors for post mortem analysis.
Finally it introduces fixes to cleanly recover from crashes in the modem
firmware on production Qualcomm devices.
-----BEGIN PGP SIGNATURE-----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=5Q77
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
- a range of improvements to the OMAP remoeteproc driver; among other
things adding devicetree, suspend/resume and watchdog support, and
adds support the remoteprocs in the DRA7xx SoC
- support for 64-bit firmware, extends the ELF loader to support this
and fixes for a number of race conditions in the recovery handling
- a generic mechanism to allow remoteproc drivers to sync state with
remote processors during a panic, and uses this to prepare Qualcomm
remote processors for post mortem analysis
- fixes to cleanly recover from crashes in the modem firmware on
production Qualcomm devices
* tag 'rproc-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc: (37 commits)
remoteproc/omap: Switch to SPDX license identifiers
remoteproc/omap: Add watchdog functionality for remote processors
remoteproc/omap: Report device exceptions and trigger recovery
remoteproc/omap: Add support for runtime auto-suspend/resume
remoteproc/omap: Add support for system suspend/resume
remoteproc/omap: Request a timer(s) for remoteproc usage
remoteproc/omap: Check for undefined mailbox messages
remoteproc/omap: Remove the platform_data header
remoteproc/omap: Add support for DRA7xx remote processors
remoteproc/omap: Initialize and assign reserved memory node
remoteproc/omap: Add the rproc ops .da_to_va() implementation
remoteproc/omap: Add support to parse internal memories from DT
remoteproc/omap: Add a sanity check for DSP boot address alignment
remoteproc/omap: Add device tree support
dt-bindings: remoteproc: Add OMAP remoteproc bindings
remoteproc: qcom: Introduce panic handler for PAS and ADSP
remoteproc: qcom: q6v5: Add common panic handler
remoteproc: Introduce "panic" callback in ops
remoteproc: Traverse rproc_list under RCU read lock
remoteproc: Fix NULL pointer dereference in rproc_virtio_notify
...
Use the appropriate SPDX license identifiers in various OMAP remoteproc
source files and drop the previous boilerplate license text.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324110035.29907-16-t-kristo@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Remote processors can be stuck in a loop, and may not be recoverable
if they do not have a built-in watchdog. The watchdog implementation
for OMAP remote processors uses external gptimers that can be used
to interrupt both the Linux host as well as the remote processor.
Each remote processor is responsible for refreshing the timer during
normal behavior - during OS task scheduling or entering the idle loop
properly. During a watchdog condition (executing a tight loop causing
no scheduling), the host processor gets interrupts and schedules a
recovery for the corresponding remote processor. The remote processor
may also get interrupted to be able to print a back trace.
A menuconfig option has also been added to enable/disable the Watchdog
functionality, with the default as disabled.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20200324110035.29907-15-t-kristo@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The OMAP remote processors send a special mailbox message
(RP_MBOX_CRASH) when they crash and detect an internal device
exception.
Add support to the mailbox handling function upon detection of
this special message to report this crash to the remoteproc core.
The remoteproc core can trigger a recovery using the prevailing
recovery mechanism, already in use for MMU Fault recovery.
Co-developed-by: Subramaniam Chanderashekarapuram <subramaniam.ca@ti.com>
Signed-off-by: Subramaniam Chanderashekarapuram <subramaniam.ca@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324110035.29907-14-t-kristo@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch enhances the PM support in the OMAP remoteproc driver to
support the runtime auto-suspend. A remoteproc may not be required to
be running all the time, and typically will need to be active only
during certain usecases. As such, to save power, it should be turned
off during potential long periods of inactivity between usecases.
This suspend and resume of the device is a relatively heavy process
in terms of latencies, so a remoteproc should be suspended only after
a certain period of prolonged inactivity. The OMAP remoteproc driver
leverages the runtime pm framework's auto_suspend feature to accomplish
this functionality. This feature is automatically enabled when a remote
processor has successfully booted. The 'autosuspend_delay_ms' for each
device dictates the inactivity period/time to wait for before
suspending the device.
The runtime auto-suspend design relies on marking the last busy time
on every communication (virtqueue kick) to and from the remote processor.
When there has been no activity for 'autosuspend_delay_ms' time, the
runtime PM framework invokes the driver's runtime pm suspend callback
to suspend the device. The remote processor will be woken up on the
initiation of the next communication message through the runtime pm
resume callback. The current auto-suspend design also allows a remote
processor to deny a auto-suspend attempt, if it wishes to, by sending a
NACK response to the initial suspend request message sent to the remote
processor as part of the suspend process. The auto-suspend request is
also only attempted if the remote processor is idled and in standby at
the time of inactivity timer expiry. This choice is made to avoid
unnecessary messaging, and the auto-suspend is simply rescheduled to
be attempted again after a further lapse of autosuspend_delay_ms.
The runtime pm callbacks functionality in this patch reuses most of the
core logic from the suspend/resume support code, and make use of an
additional auto_suspend flag to differentiate the logic in common code
from system suspend. The system suspend/resume sequences are also updated
to reflect the proper pm_runtime statuses, and also to really perform a
suspend/resume only if the remoteproc has not been auto-suspended at the
time of request. The remote processor is left in suspended state on a
system resume if it has been auto-suspended before, and will be woken up
only when a usecase needs to run.
The OMAP remoteproc driver currently uses a default value of 10 seconds
for all OMAP remoteprocs, and a different value can be chosen either by
choosing a positive value for the 'ti,autosuspend-delay-ms' under DT or
by updating the 'autosuspend_delay_ms' field at runtime through the
sysfs interface. A negative value is equivalent to disabling the runtime
suspend.
Eg: To use 25 seconds for IPU2 on DRA7xx,
echo 25000 > /sys/bus/platform/devices/55020000.ipu/power/autosuspend_delay_ms
The runtime suspend feature can also be similarly enabled or disabled by
writing 'auto' or 'on' to the device's 'control' power field. The default
is enabled.
Eg: To disable auto-suspend for IPU2 on DRA7xx SoC,
echo on > /sys/bus/platform/devices/55020000.ipu/power/control
Signed-off-by: Suman Anna <s-anna@ti.com>
[t-kristo@ti.com: converted to use ti-sysc instead of hwmod]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324110035.29907-13-t-kristo@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch adds the support for system suspend/resume to the
OMAP remoteproc driver so that the OMAP remoteproc devices can
be suspended/resumed during a system suspend/resume. The support
is added through the driver PM .suspend/.resume callbacks, and
requires appropriate support from the OS running on the remote
processors.
The IPU & DSP remote processors typically have their own private
modules like registers, internal memories, caches etc. The context
of these modules need to be saved and restored properly for a
suspend/resume to work. These are in general not accessible from
the MPU, so the remote processors themselves have to implement
the logic for the context save & restore of these modules.
The OMAP remoteproc driver initiates a suspend by sending a mailbox
message requesting the remote processor to save its context and
enter into an idle/standby state. The remote processor should
usually stop whatever processing it is doing to switch to a context
save mode. The OMAP remoteproc driver detects the completion of
the context save by checking the module standby status for the
remoteproc device. It also stops any resources used by the remote
processors like the timers. The timers need to be running only
when the processor is active and executing, and need to be stopped
otherwise to allow the timer driver to reach low-power states. The
IOMMUs are automatically suspended by the PM core during the late
suspend stage, after the remoteproc suspend process is completed by
putting the remote processor cores into reset. Thereafter, the Linux
kernel can put the domain into further lower power states as possible.
The resume sequence undoes the operations performed in the PM suspend
callback, by starting the timers and finally releasing the processors
from reset. This requires that the remote processor side OS be able to
distinguish a power-resume boot from a power-on/cold boot, restore the
context of its private modules saved during the suspend phase, and
resume executing code from where it was suspended. The IOMMUs would
have been resumed by the PM core during early resume, so they are
already enabled by the time remoteproc resume callback gets invoked.
The remote processors should save their context into System RAM (DDR),
as any internal memories are not guaranteed to retain context as it
depends on the lowest power domain that the remote processor device
is put into. The management of the DDR contents will be managed by
the Linux kernel.
Signed-off-by: Suman Anna <s-anna@ti.com>
[t-kristo@ti.com: converted to use ti-sysc instead of hwmod]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324110035.29907-12-t-kristo@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The remote processors in OMAP4+ SoCs are equipped with internal
timers, like the internal SysTick timer in a Cortex M3/M4 NVIC or
the CTM timer within Unicache in IPU & DSP. However, these timers
are gated when the processor subsystem clock is gated, making
them rather difficult to use as OS tick sources. They will not
be able to wakeup the processor from any processor-sleep induced
clock-gating states.
This can be avoided by using an external timer as the tick source,
which can be controlled independently by the OMAP remoteproc
driver code, but still allowing the processor subsystem clock to
be auto-gated when the remoteproc cores are idle.
This patch adds the support for OMAP remote processors to request
timer(s) to be used by the remoteproc. The timers are enabled and
disabled in line with the enabling/disabling of the remoteproc.
The timer data is not mandatory if the advanced device management
features are not required.
The core timer functionality is provided by the OMAP DMTimer
clocksource driver, which does not export any API. The logic is
implemented through the timer device's platform data ops. The OMAP
remoteproc driver mainly requires ops to request/free a dmtimer,
and to start/stop a timer. The split ops helps in controlling the
timer state without having to request and release a timer everytime
it needs to use the timer.
NOTE: If the gptimer is already in use by the time IPU and/or
DSP are loaded, the processors will fail to boot.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324110035.29907-11-t-kristo@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add some checks in the mailbox callback function to limit
any processing in the mailbox callback function to only
certain currently valid messages, and drop all the remaining
messages. A debug message is added to print any such invalid
messages when the appropriate trace control is enabled.
Co-developed-by: Subramaniam Chanderashekarapuram <subramaniam.ca@ti.com>
Signed-off-by: Subramaniam Chanderashekarapuram <subramaniam.ca@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324110035.29907-10-t-kristo@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
DRA7xx/AM57xx SoCs have two IPU and up to two DSP processor subsystems
for offloading different computation algorithms. The IPU processor
subsystem contains dual-core ARM Cortex-M4 processors, and is very
similar to those on OMAP5. The DSP processor subsystem is based on
the TI's standard TMS320C66x DSP CorePac core.
Support has been added to the OMAP remoteproc driver through new
DRA7xx specific compatibles for properly probing and booting all
the different processor subsystem instances on DRA7xx/AM57xx
SoCs - IPU1, IPU2, DSP1 & DSP2. A build dependency with SOC_DRA7XX
is added to enable the driver to be built in DRA7xx-only configuration.
The DSP boot address programming needed enhancement for DRA7xx as the
boot register fields are different on DRA7 compared to OMAP4 and OMAP5
SoCs. The register on DRA7xx contains additional fields within the
register and the boot address bit-field is right-shifted by 10 bits.
The internal memory parsing logic has also been updated to compute
the device addresses for the L2 RAM for DSP devices using relative
addressing logic, and to parse two additional RAMs at L1 level - L1P
and L1D. This allows the remoteproc driver to support loading into
these regions for a small subset of firmware images requiring as
such. The most common usage would be to use the L1 programmable
RAMs as L1 Caches.
The firmware lookup logic also has to be adjusted for DRA7xx as
there are (can be) more than one instance of both the IPU and DSP
remote processors for the first time in OMAP4+ SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
[t-kristo@ti.com: moved address translation quirks to pdata]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324110035.29907-8-t-kristo@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The reserved memory nodes are not assigned to platform devices by
default in the driver core to avoid the lookup for every platform
device and incur a penalty as the real users are expected to be
only a few devices.
OMAP remoteproc devices fall into the above category and the OMAP
remoteproc driver _requires_ specific CMA pools to be assigned
for each device at the moment to align on the location of the
vrings and vring buffers in the RTOS-side firmware images. So,
use the of_reserved_mem_device_init/release() API appropriately
to assign the corresponding reserved memory region to the OMAP
remoteproc device. Note that only one region per device is
allowed by the framework.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324110035.29907-7-t-kristo@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
An implementation for the rproc ops .da_to_va() has been added
that provides the address translation between device addresses
to kernel virtual addresses for internal RAMs present on that
particular remote processor device. The implementation provides
the translations based on the addresses parsed and stored during
the probe.
This ops gets invoked by the exported rproc_da_to_va() function
and allows the remoteproc core's ELF loader to be able to load
program data directly into the internal memories.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324110035.29907-6-t-kristo@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The OMAP remoteproc driver has been enhanced to parse and store
the kernel mappings for different internal RAM memories that may
be present within each remote processor IP subsystem. Different
devices have varying memories present on current SoCs. The current
support handles the L2RAM for all IPU devices on OMAP4+ SoCs. The
DSPs on OMAP4/OMAP5 only have Unicaches and do not have any L1 or
L2 RAM memories.
IPUs are expected to have the L2RAM at a fixed device address of
0x20000000, based on the current limitations on Attribute MMU
configurations.
NOTE:
The current logic doesn't handle the parsing of memories for DRA7
remoteproc devices, and will be added alongside the DRA7 support.
Signed-off-by: Suman Anna <s-anna@ti.com>
[t-kristo: converted to parse mem names / device addresses from pdata]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324110035.29907-5-t-kristo@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The DSP remote processors on OMAP SoCs require a boot register to
be programmed with a boot address, and this boot address needs to
be on a 1KB boundary. The current code is simply masking the boot
address appropriately without performing any sanity checks before
releasing the resets. An unaligned boot address results in an
undefined execution behavior and can result in various bus errors
like MMU Faults or L3 NoC errors. Such errors are hard to debug and
can be easily avoided by adding a sanity check for the alignment
before booting a DSP remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324110035.29907-4-t-kristo@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
OMAP4+ SoCs support device tree boot only. The OMAP remoteproc
driver is enhanced to support remoteproc devices created through
Device Tree, support for legacy platform devices has been
deprecated. The current DT support handles the IPU and DSP
processor subsystems on OMAP4 and OMAP5 SoCs.
The OMAP remoteproc driver relies on the ti-sysc, reset, and
syscon layers for performing clock, reset and boot vector
management (DSP remoteprocs only) of the devices, but some of
these are limited only to the machine-specific layers
in arch/arm. The dependency against control module API for boot
vector management of the DSP remoteprocs has now been removed
with added logic to parse the boot register from the DT node
and program it appropriately directly within the driver.
The OMAP remoteproc driver expects the firmware names to be
provided via device tree entries (firmware-name.) These are used
to load the proper firmware during boot of the remote processor.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
[t-kristo@ti.com: converted to use ti-sysc framework]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324110035.29907-3-t-kristo@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Make the PAS and ADSP/CDSP remoteproc drivers implement the panic
handler that will invoke a stop to prepare the remoteprocs for post
mortem debugging.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324052904.738594-5-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a common panic handler that invokes a stop request and sleep enough
to let the remoteproc flush it's caches etc in order to aid post mortem
debugging. For now a hard coded 200ms is returned to the remoteproc
core, this value is taken from the downstream kernel.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324052904.738594-4-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Introduce generic support for handling kernel panics in remoteproc
drivers, in order to allow operations needed for aiding in post mortem
system debugging, such as flushing caches etc.
The function can return a number of milliseconds needed by the remote to
"settle" and the core will wait the longest returned duration before
returning from the panic handler.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324052904.738594-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In order to be able to traverse the mostly read-only rproc_list without
locking during panic migrate traversal to be done under rcu_read_lock().
Mutual exclusion for modifications of the list continues to be handled
by the rproc_list_mutex and a synchronization point is added before
releasing objects that are popped from the list.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200324052904.738594-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If the value written to the "recovery" debugfs file is not one of
the recognized commands return an error to indicate it's invalid.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20200228183359.16229-5-elder@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Don't bother checking the remoteproc state before calling
rproc_trigger_recovery() because that function will verify the
state, and the state can only be safely checked while holding the
mutex anyway.
Make the mode for "recovery" be writable.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20200228183359.16229-3-elder@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Two places call rproc_trigger_recovery():
- rproc_crash_handler_work() sets rproc->state to CRASHED under
protection of the mutex, then calls it if recovery is not
disabled. This function is called in workqueue context when
scheduled in rproc_report_crash().
- rproc_recovery_write() calls it in two spots, both of which
the only call it if the rproc->state is CRASHED.
The mutex is taken right away in rproc_trigger_recovery(). However,
by the time the mutex is acquired, something else might have changed
rproc->state to something other than CRASHED.
The work that follows that is only appropriate for a remoteproc in
CRASHED state. So check the state after acquiring the mutex, and
only proceed with the recovery work if the remoteproc is still in
CRASHED state.
Delay reporting that recovering has begun until after we hold the
mutex and we know the remote processor is in CRASHED state.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20200228183359.16229-2-elder@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The mainline device trees lack the "st,syscfg-pdds", so probing the
driver always throws the warning. As the property is optional per binding
and the driver can deal with its absence, demote the warning to info log
level.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20200224172519.15315-1-a.fatoum@pengutronix.de
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Clang errors:
drivers/remoteproc/mtk_scp.c:364:14: error: incompatible function
pointer types initializing 'void *(*)(struct rproc *, u64, size_t)' (aka
'void *(*)(struct rproc *, unsigned long long, unsigned int)') with an
expression of type 'void *(struct rproc *, u64, int)' (aka 'void
*(struct rproc *, unsigned long long, int)')
[-Werror,-Wincompatible-function-pointer-types]
.da_to_va = scp_da_to_va,
^~~~~~~~~~~~
1 error generated.
Make the same change as commit 0fcbb369f052 ("remoteproc: Use size_t
type for len in da_to_va"), which was not updated for the acceptance of
commit 63c13d61ea ("remoteproc/mediatek: add SCP support for mt8183").
Fixes: 0fcbb369f052 ("remoteproc: Use size_t type for len in da_to_va")
Link: https://github.com/ClangBuiltLinux/linux/issues/927
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20200310211514.32288-1-natechancellor@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Now that remoteproc can load an elf64, coredump elf class should be
the same as the loaded elf class. In order to do that, add a
elf_class field to rproc with default values. If an elf is loaded
successfully, this field will be updated with the loaded elf class.
Then, the coredump core code has been modified to use the generic elf
macro in order to create an elf file with correct class.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20200302093902.27849-9-cleger@kalray.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Now that rproc_elf_sanity_check can be used by external drivers, allow
to only overwrite the sanity_check member of rproc_ops. This will allow
drivers to handle elf32 and elf64 by overwriting sanity_check with
rproc_elf_sanity_check function.
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20200302093902.27849-8-cleger@kalray.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In order to support elf64, use macros from remoteproc_elf_helpers.h
to access elf headers depending on elf class.
To allow new drivers to support elf64, add rproc_elf_sanity_check
function which make more sense than adding a elf64 named one since
it will support both elf versions.
Driver which need to support both elf32/elf64 should use this new
function for elf sanity check instead of the elf32 one.
Signed-off-by: Clement Leger <cleger@kalray.eu>
Tested-by: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200302093902.27849-7-cleger@kalray.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Since this function will be modified to support both elf32 and elf64,
rename the existing one to elf32 (which is the only supported format
at the moment). This will allow not to introduce possible side effect
when adding elf64 support (ie: all backends will still support only
elf32 if not requested explicitely using rproc_elf_sanity_check).
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20200302093902.27849-6-cleger@kalray.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
elf32 and elf64 mainly differ by their types. In order to avoid
copy/pasting the whole loader code, generate static inline functions
which will access values according to the elf class. It allows to
keep a common loader basis.
In order to accommodate both elf types sizes, the maximum size for a
elf header member is chosen using the maximum value of the field for
both elf class.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20200302093902.27849-5-cleger@kalray.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
elf64 entry is defined as a u64. Since boot_addr is used to store the
elf entry point, change boot_addr type to u64 to support both elf32
and elf64. In the same time, fix users that were using this variable.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20200302093902.27849-4-cleger@kalray.eu
[bjorn: Fixes up return type of rproc_get_boot_addr()]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Now that rproc_da_to_va uses a size_t for length, use a size_t for len
field of rproc_mem_entry. Function used to create such structures now
takes a size_t instead of int to allow full size range to be handled.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20200302093902.27849-3-cleger@kalray.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
With upcoming changes in elf loader for elf64 support, section size will
be a u64. When used with da_to_va, this will potentially lead to
overflow if using the current "int" type for len argument. Change
da_to_va prototype to use a size_t for len and fix all users of this
function.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20200302093902.27849-2-cleger@kalray.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix the following warnings when documentation is built:
drivers/remoteproc/remoteproc_virtio.c:330: warning: Function parameter
or member 'id' not described in 'rproc_add_virtio_dev'
drivers/remoteproc/remoteproc_core.c:243: warning: Function parameter
or member 'name' not described in 'rproc_find_carveout_by_name'
drivers/remoteproc/remoteproc_core.c:473: warning: Function parameter
or member 'offset' not described in 'rproc_handle_vdev'
drivers/remoteproc/remoteproc_core.c:604: warning: Function parameter
or member 'offset' not described in 'rproc_handle_trace'
drivers/remoteproc/remoteproc_core.c:678: warning: Function parameter
or member 'offset' not described in 'rproc_handle_devmem'
drivers/remoteproc/remoteproc_core.c:873: warning: Function parameter
or member 'offset' not described in 'rproc_handle_carveout'
drivers/remoteproc/remoteproc_core.c:1029: warning: cannot understand function
prototype: 'rproc_handle_resource_t rproc_loading_handlers[RSC_LAST] = '
drivers/remoteproc/remoteproc_core.c:1693: warning: Function parameter
or member 'work' not described in 'rproc_crash_handler_work'
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200212161956.10358-1-arnaud.pouliquen@st.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On secure devices after a wdog/fatal interrupt, the mba region has to be
refreshed in order to prevent the following errors during mba load.
Err Logs:
remoteproc remoteproc2: stopped remote processor 4080000.remoteproc
qcom-q6v5-mss 4080000.remoteproc: PBL returned unexpected status -284031232
qcom-q6v5-mss 4080000.remoteproc: PBL returned unexpected status -284031232
....
qcom-q6v5-mss 4080000.remoteproc: PBL returned unexpected status -284031232
qcom-q6v5-mss 4080000.remoteproc: MBA booted, loading mpss
Fixes: 7dd8ade24d ("remoteproc: qcom: q6v5-mss: Add custom dump function for modem")
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200304194729.27979-4-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The code used to sync with the MBA after each segment loaded and this is
still what's done downstream. So reduce the delta towards downstream by
switching to a model where the content is iteratively validated.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200304194729.27979-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Trying to reclaim mpss memory while the mba is not running causes the
system to crash on devices with security fuses blown, so leave it
assigned to the remote on shutdown and recover it on a subsequent boot.
Fixes: 6c5a9dc248 ("remoteproc: qcom: Make secure world call for mem ownership switch")
Cc: stable@vger.kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200304194729.27979-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Rearrange the config files for remoteproc and IPA to fix their
interdependencies.
First, have CONFIG_QCOM_Q6V5_MSS select QCOM_Q6V5_IPA_NOTIFY so the
notification code is built regardless of whether IPA needs it.
Next, represent QCOM_IPA as being dependent on QCOM_Q6V5_MSS rather
than setting its value to match QCOM_Q6V5_COMMON (which is selected
by QCOM_Q6V5_MSS).
Drop all dependencies from QCOM_Q6V5_IPA_NOTIFY. The notification
code will be built whenever QCOM_Q6V5_MSS is set, and it has no other
dependencies.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set up a subdev in the q6v5 modem remoteproc driver that generates
event notifications for the IPA driver to use for initialization and
recovery following a modem shutdown or crash.
A pair of new functions provides a way for the IPA driver to register
and deregister a notification callback function that will be called
whenever modem events (about to boot, running, about to shut down,
etc.) occur. A void pointer value (provided by the IPA driver at
registration time) and an event type are supplied to the callback
function.
One event, MODEM_REMOVING, is signaled whenever the q6v5 driver is
about to remove the notification subdevice. It requires the IPA
driver de-register its callback.
This sub-device is only used by the modem subsystem (MSS) driver,
so the code that adds the new subdev and allows registration and
deregistration of the notifier is found in "qcom_q6v6_mss.c".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define AXI_GATING_VALID_OVERRIDE and fixup comments to improve readability
of Q6 modem reset sequence on SC7180 SoCs.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200123131236.1078-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Replace the loop for HALT_ACK detection with regmap_read_poll_timeout.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200123131236.1078-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Rename the FSM timeout on SC7180 to BOOT_STATUS_TIMEOUT_US.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200117135130.3605-4-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Define CLKEN and CLKOFF for improving readability of Q6SS clock
handling.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200117135130.3605-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct fw_rsc_vdev {
...
struct fw_rsc_vdev_vring vring[0];
} __packed;
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following form:
sizeof(*rsc) + rsc->num_of_vrings * sizeof(struct fw_rsc_vdev_vring)
with:
struct_size(rsc, vring, rsc->num_of_vrings)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190830151406.GA23274@embeddedor
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Provide a basic driver to control Cortex M4 co-processor
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Link: https://lore.kernel.org/r/20191112110330.179649-3-pihsun@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the out of reset sequence support for modem sub-system on SC7180
SoCs. It requires access to an additional halt nav register to put
the modem back into reset.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20191219054506.20565-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently the mem clk is voted upon from both the active and proxy pool on
MSM8998 SoCs where only a proxy vote should suffice. Fix this by removing
mem clk from the active pool.
Fixes: 1665cbd573 ("remoteproc: qcom_q6v5_mss: Add support for MSM8998")
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20191218132217.28141-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If the rproc driver is probed before the mailbox driver and if the rproc
Device Tree node has some mailbox properties, the rproc driver probe
shall be deferred instead of being probed without mailbox support.
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Link: https://lore.kernel.org/r/1573812188-19842-1-git-send-email-fabien.dessenne@st.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If the device node defines the 'wakeup-source' property, use the WDG
exti IRQ as a wakeup source of the system.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Link: https://lore.kernel.org/r/1566833923-16718-3-git-send-email-fabien.dessenne@st.com
[bjorn: Replace ifdef with __maybe_unused for suspend/resume functions]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Index of rvring is computed using pointer arithmetic. However, since
rvring->rvdev->vring is the base of the vring array, computation
of rvring idx should be reversed. It previously lead to writing at negative
indices in the resource table.
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20191004073736.8327-1-cleger@kalray.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The mailbox callback is under interrupt context. A consequence is
that RPMsg Callbacks are also in interrupt context.
Create workqueue to treat the callbacks in normal context.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The rproc_mem_entry_init() call takes a pointer to a vm
as the second argument. The code is currently using a
plain 0 as "NULL". Change to using NULL to fix the
following sparse warnings:
drivers/remoteproc/remoteproc_core.c:339:49: warning: Using plain integer as NULL pointer
drivers/remoteproc/remoteproc_core.c:916:46: warning: Using plain integer as NULL pointer
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
MSM8998 sits between MSM8996 and SDM845 in terms of functionality needed to
boot the modem subsystem. Booting mss allows for servicing the traditional
cellular usecases along with the wireless usecases such as wifi.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
debugfs_remove_recursive will do NULL check, so remove
the redundant null check
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
rproc_handle_resources_t is not used anymore, remove it.
Signed-off-by: Clement Leger <cleger@kalray.eu>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This exposes the remoteproc's name in sysfs, allows stm32 to enter
platform standby and provides bug fixes for stm32 and Qualcomm's modem
remoteproc drivers. Finally it updates MAINTAINERS to reflect the move
to kernel.org.
-----BEGIN PGP SIGNATURE-----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=T/PI
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This exposes the remoteproc's name in sysfs, allows stm32 to enter
platform standby and provides bug fixes for stm32 and Qualcomm's modem
remoteproc drivers. Finally it updates MAINTAINERS to reflect the move
to kernel.org"
* tag 'rproc-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
MAINTAINERS: remoteproc: update git tree location
remoteproc: Remove dev_err() usage after platform_get_irq()
remoteproc: stm32: manage the get_irq probe defer case
remoteproc: stm32: clear MCU PDDS at firmware start
remoteproc: qcom: q6v5-mss: fixup q6v5_pds_enable error handling
remoteproc: Add a sysfs interface for name
remoteproc: qcom: Move glink_ssr notification after stop
Remoteproc started using dma_declare_coherent_memory recently, which is
a bad idea from drivers, and the maintainers agreed to fix that. But
until that is fixed only allow building the driver built in so that we
can remove the dma_declare_coherent_memory export and prevent other
drivers from "accidentally" using it like remoteproc. Note that the
driver would also leak the declared coherent memory on unload if it
actually was built as a module at the moment.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-remoteproc@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When remoteproc stops a firmware, it sets the MCU PDDS flag, allowing
the platform to reach the Standby power mode if needed.
Symmetrically, clear this flag before running a firmware.
This fixes the issue where the system goes to Standby mode when the
MCU crashes while MPU is in CSTOP mode.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
dev_pm_domain_attach_by_name will return NULL if the requested
power-domain is not a part device node. This could result in
NULL pointer de-reference in q6v5_pds_enable. Fix this by
checking for IS_ERR_OR_NULL and forward the appropriate error
code.
Fixes: 4760a896be ("remoteproc: q6v5-mss: Vote for rpmh power domains")
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch adds a sysfs interface that provides the name of the
remote processor to userspace. This allows the userspace to identify
a remote processor as the remoteproc devices themselves are created
based on probe order and can change from one boot to another or
at runtime.
The name is made available in debugfs originally, and is being
retained for now. This can be cleaned up after couple of releases
once users get familiar with the new interface.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
glink_ssr is used to signal a remote processor "A" about the stopping of
another remote processor "B", so that in the event that remote processor
B is ever booted again the fifos of the glink channel between A and B is
in a known state.
But if remote processor A receives this notification before B is
actually stopped the newly reset fifo indices will be interpreted as
there being "data" on the channel and either side of the channel will
enter a fatal error handler.
Move the glink_ssr notification to the "unprepare" state of the
rproc_subdev to avoid this issue.
This has the side effect of us not notifying the dying remote processor
itself about its fate, which has been seen to block in certain resource
constraint scenarios.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This adds support for the STM32 remoteproc, additional i.MX platforms
with Cortex M4 remoteprocs and Qualcomm's QCS404 Compute DSP. Initial
support for vendor specific resource table entries and support for
unprocessed Qualcomm firmware files.
-----BEGIN PGP SIGNATURE-----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=iqXq
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.3' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This adds support for the STM32 remoteproc, additional i.MX platforms
with Cortex M4 remoteprocs and Qualcomm's QCS404 Compute DSP.
Also initial support for vendor specific resource table entries and
support for unprocessed Qualcomm firmware files"
* tag 'rproc-v5.3' of git://github.com/andersson/remoteproc:
remoteproc: stm32: fix building without ARM SMCC
remoteproc: qcom: q6v5-mss: Fix build error without QCOM_MDT_LOADER
remoteproc: copy parent dma_pfn_offset for vdev
remoteproc: qcom: q6v5-mss: Support loading non-split images
soc: qcom: mdt_loader: Support loading non-split images
remoteproc: stm32: add an ST stm32_rproc driver
dt-bindings: remoteproc: add bindings for stm32 remote processor driver
dt-bindings: stm32: add bindings for ML-AHB interconnect
remoteproc: Use struct_size() helper
remoteproc: add vendor resources handling
remoteproc: imx: Fix typo in "failed"
remoteproc: imx: Broaden the Kconfig selection logic
remoteproc,rpmsg: add missing MAINTAINERS file entries
remoteproc: qcom: qdsp6-adsp: Add support for QCS404 CDSP
dt-bindings: remoteproc: Rename and amend Hexagon v56 binding
When compile testing this driver without SMCC support enabled,
we get a link error:
drivers/remoteproc/stm32_rproc.o: In function `stm32_rproc_start':
stm32_rproc.c:(.text+0x776): undefined reference to `__arm_smccc_smc'
drivers/remoteproc/stm32_rproc.o: In function `stm32_rproc_stop':
stm32_rproc.c:(.text+0x92c): undefined reference to `__arm_smccc_smc'
Make the actual call to arm_smccc_smc conditional on the Kconfig
symbol controlling its implementation.
Fixes: 13140de09c ("remoteproc: stm32: add an ST stm32_rproc driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If QCOM_Q6V5_MSS is set but QCOM_MDT_LOADER is not,
building will fails:
drivers/remoteproc/qcom_q6v5_mss.o: In function `q6v5_start':
qcom_q6v5_mss.c:(.text+0x3260): undefined reference to `qcom_mdt_read_metadata'
Add QCOM_MDT_LOADER dependency for QCOM_Q6V5_MSS.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: f04b913834 ("remoteproc: qcom: q6v5-mss: Support loading non-split images")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When preparing the subdevice for the vdev, also copy dma_pfn_offset
since this is used for sub device dma allocations. Without that, there
is incoherency between the parent dma settings and the childs one,
potentially leading to dma_alloc_coherent failure (due to phys_to_dma
using dma_pfn_offset for translation).
Fixes: 086d08725d ("remoteproc: create vdev subdevice with specific dma memory pool")
Signed-off-by: Clement Leger <cleger@kalray.eu>
Acked-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In some software releases the firmware images are not split up with each
loadable segment in it's own file. Check the size of the loaded firmware
to see if it still contains each segment to be loaded, before falling
back to the split-out segments.
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch introduces a new remoteproc driver to control Cortex-M4
co-processor of the STM32 family.
It provides with the following features:
- start and stop
- dedicated co-processor memory regions registration
- coredump and recovery
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
[bjorn: Fixup of dev_dbg types and cast of int to pointer in mbox send]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct resource_table {
...
u32 offset[0];
} __packed;
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following form:
table->num * sizeof(table->offset[0]) + sizeof(struct resource_table)
with:
struct_size(table, offset, table->num)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In order to allow rproc backend to handle vendor resources such as in
OpenAMP, add a handle_rsc hook. This hook allow the rproc backends to
handle vendor resources as they like. The hook will be called only for
vendor resources and should return RSC_HANDLED on successful resource
handling, RSC_IGNORED if resource was ignored, or a negative value on
error.
Signed-off-by: Clement Leger <cleger@kalray.eu>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several places where "failed" is spelled incorrectly.
Fix them all.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Besides i.MX6SX and i.MX7D, there are other i.MX devices that contain
Cortex M4 and could make use of the imx remoteproc driver, such as
i.MX7ULP, i.MX8M, etc.
Instead of adding new SoC entries in the Kconfig logic, make it
broader by using the more generic ARCH_MXC, which encompasses
all the 32-bit and 64-bit i.MX devices.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the clock list to adsp_pil_data, make the pdc_reset optional and
make the driver directly enable the xo, sleep and core clocks.
The three clocks are previously toggled through the clock controller,
but that means the same hardware block needs to be mapped in both
drivers. Making the remoteproc driver enable the clocks is a nop when
using the clock controller, but allow us to remove the clocks from the
clock controller.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This contains the last patches in Loic's remoteproc resource table
handling changes, a number of updates to documentation, support for
invoking the crash handler (for testing purposes), a fix for the
handling of virtio devices during recovery, performance state votes in
Qualcomm modem driver, support for specifying board specific firmware
path for Qualcomm modem driver and improved support for graceful
shutdown of Qualcomm remoteprocs.
-----BEGIN PGP SIGNATURE-----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=4xC9
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.1' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This contains the last patches in Loic's remoteproc resource table
handling changes, a number of updates to documentation, support for
invoking the crash handler (for testing purposes), a fix for the
handling of virtio devices during recovery, performance state votes in
Qualcomm modem driver, support for specifying board specific firmware
path for Qualcomm modem driver and improved support for graceful
shutdown of Qualcomm remoteprocs"
* tag 'rproc-v5.1' of git://github.com/andersson/remoteproc: (33 commits)
remoteproc: fix for "dma-mapping: remove the DMA_MEMORY_EXCLUSIVE flag"
remoteproc: fix rproc_check_carveout_da() returned error and comments
remoteproc: fix trace buffer va initialization
remoteproc: fix rproc_alloc_carveout() for rproc with iommu domain
remoteproc: add warning on resource table cast
remoteproc: fix rproc_alloc_carveout() bad variable cast
remoteproc: fix rproc_da_to_va in case of unallocated carveout
remoteproc: correct rproc_mem_entry_init() comments
remoteproc: fix recovery procedure
rpmsg: virtio: change header file sort style
rpmsg: virtio: allocate buffer from parent
remoteproc: st: add reserved memory support
remoteproc: create vdev subdevice with specific dma memory pool
remoteproc: q6v5_adsp: Remove voting for lpass_aon clock
dt-binding: remoteproc: Remove lpass_aon clock from adsp pil clock list
remoteproc: q6v5-mss: Active powerdomain for SDM845
remoteproc: q6v5-mss: Vote for rpmh power domains
remoteproc: qcom: Add support for parsing fw dt bindings
remoteproc: qcom_q6v5: don't auto boot remote processor
remoteproc: qcom: Wait for shutdown-ack/ind on sysmon shutdown
...
The commit 82c5de0ab8 ("dma-mapping: remove the DMA_MEMORY_EXCLUSIVE
flag") removed the "flags" parameter for dma_declare_coherent_memory().
Remove the parameter from the call in rproc_add_virtio_dev().
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[bjorn: Extended commit message]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix typo in comments.
Change returned error from ENOMEM to EINVAL as
not dealing with memory allocation.
Remove carveout forced da update and return an error
when no configuration match
Fixes: c874bf59ad ("remoteproc: add helper function to check carveout device address")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
With rproc_alloc_registered_carveouts() introduction, carveouts are
allocated after resource table parsing.
rproc_da_to_va() may return NULL at trace resource registering.
This patch modifies trace debufs registering to provide device address
(da) instead of va.
da to va translation is done at each trace buffer access
through debugfs interface.
Fixes: d7c51706d0 ("remoteproc: add alloc ops in rproc_mem_entry struct")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Correct remoteproc core behavior when memory carveout device
address is fixed in resource table and rproc device doesn't have
associated IOMMU.
Current returned error is breaking legacy on TI platforms.
This patch restores previous behavior. It adds a warn message when
allocation doesn't fit carveout request, but doesn't stop rproc_start()
sequence anymore.
Fixes: 3bc8140b15 ("remoteproc: configure IOMMU only if device address requested")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Today resource table supports only 32bit address fields.
This is not compliant with 64bit platform for which addresses
are cast in 32bit.
This patch adds warn messages when address cast is done.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
As dma member of struct rproc_mem_entry is dma_addr_t, no
need to cast in u32.
Fixes: d7c51706d0 ("remoteproc: add alloc ops in rproc_mem_entry struct")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
With introduction of rproc_alloc_registered_carveouts() which
delays carveout allocation just before the start of the remote
processor, rproc_da_to_va() could be called before all carveouts
are allocated.
This patch adds a check in rproc_da_to_va() to return NULL if
carveout is not allocated.
Fixes: d7c51706d0 ("remoteproc: add alloc ops in rproc_mem_entry struct")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Mathieu Poirier
Sibi Sankar
Bjorn Andersson
Lee Jones
Kefeng Wang
Rishabh Bhatnagar
Herbert Xu
Linus Torvalds
Dan Carpenter
Paul Cercueil
Suman Anna
Tero Kristo
Sivaprakash Murugesan
Wei Yongjun
Christophe JAILLET
Loic Pallardy
Clement Leger
Siddharth Gupta
Alex Elder
Michael S. Tsirkin
Yangtao Li
Arnd Bergmann
Nathan Chancellor
Nikita Shubin
Ahmad Fatoum
Arnaud Pouliquen
Gustavo A. R. Silva
Brandon Maier
Pi-Hsun Shih
Erin Lo
Ma Feng
Fabien Dessenne
Ben Dooks (Codethink)
Jeffrey Hugo
Ding Xiang
Christoph Hellwig
Stephen Boyd
YueHaibing
Thomas Gleixner
Fabio Estevam
Stephen Rothwell