The complete size ("total_size") of the fragmented packet is stored in the
fragment header and in the size of the fragment chain. When the fragments
are ready for merge, the skbuff's tail of the first fragment is expanded to
have enough room after the data pointer for at least total_size. This means
that it gets expanded by total_size - first_skb->len.
But this is ignoring the fact that after expanding the buffer, the fragment
header is pulled by from this buffer. Assuming that the tailroom of the
buffer was already 0, the buffer after the data pointer of the skbuff is
now only total_size - len(fragment_header) large. When the merge function
is then processing the remaining fragments, the code to copy the data over
to the merged skbuff will cause an skb_over_panic when it tries to actually
put enough data to fill the total_size bytes of the packet.
The size of the skb_pull must therefore also be taken into account when the
buffer's tailroom is expanded.
Fixes: 610bfc6bc9 ("batman-adv: Receive fragmented packets and merge")
Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Co-authored-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The announcement messages of batman-adv COMPAT_VERSION 15 have the
possibility to announce additional information via a dynamic TVLV part.
This part is optional for the ELP packets and currently not parsed by the
Linux implementation. Still out-of-tree versions are using it to transport
things like neighbor hashes to optimize the rebroadcast behavior.
Since the ELP broadcast packets are smaller than the minimal ethernet
packet, it often has to be padded. This is often done (as specified in
RFC894) with octets of zero and thus work perfectly fine with the TVLV
part (making it a zero length and thus empty). But not all ethernet
compatible hardware seems to follow this advice. To avoid ambiguous
situations when parsing the TVLV header, just force the 4 bytes (TVLV
length + padding) after the required ELP header to zero.
Fixes: d6f94d91f7 ("batman-adv: ELP - adding basic infrastructure")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
The batadv interfaces are virtual interfaces which just tunnel the traffic
over other ethernet compatible interfaces. It doesn't need serialization
during the tx phase and is using RCU for most of its internal
datastructures. Since it doesn't have actual queues which could be locked
independently, the throughput gets significantly reduced by the extra lock
in the core net code.
8 parallel TCP connections forwarded by an IPQ4019 based hardware over
5GHz could reach:
* without LLTX: 349 Mibit/s
* with LLTX: 563 Mibit/s
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
B.A.T.M.A.N. IV requires the number of rebroadcast from a neighboring
originator. These statistics are gathered per interface which transmitted
the OGM (and then received it again). Since an originator is not interface
specific, a resizable array was used in each originator.
This resizable array had an entry for each interface and had to be resizes
(for all OGMs) when the number of active interface was modified. This could
cause problems when a large number of interface is added and not enough
continuous memory is available to allocate the array.
There is already a per interface originator structure "batadv_orig_ifinfo"
which can be used to store this information.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
A private debug logging infrastructure is currently provided via
$debug_fs/batman_adv/*/log when CONFIG_BATMAN_ADV_DEBUG is enabled. This is
not well integrated in the rest of the tracing infrastructure of the
kernel.
Other components (like mac80211 or ath10k) allow to gather the debug
messages using generic trace events which are better integrated. This makes
it possible to interact with them using the existing userspace tools.
The tracepoint batadv:batadv_dbg will now be available when
CONFIG_BATMAN_ADV_DEBUG and CONFIG_BATMAN_ADV_TRACING is activated. The log
level mask is still used for filtering as usual.
A full system trace for offline parsing can be created (and read) using:
$ batctl ll all
$ trace-cmd record -e batadv:batadv_dbg
$ trace-cmd report
The same can also be done without recording to a file
$ batctl ll all
$ trace-cmd stream -e batadv:batadv_dbg
The trace infrastructure is especially helpful when tracing processes:
$ batctl ll all
$ ./tools/perf/perf trace --event "batadv:*" batctl p 10.204.32.1
0.000 batadv:batadv_dbg:batman_adv bat0 Parsing outgoing ARP REQUEST
0.045 batadv:batadv_dbg:batman_adv bat0 ARP MSG = [src: a2:64:14:53:f8:22-10.204.32.185 dst: 00:00:00:00:00:00-10.204.32.1]
0.067 batadv:batadv_dbg:batman_adv bat0 Entry updated: 10.204.32.185 a2:64:14:53:f8:22 (vid: -1)
0.099 batadv:batadv_dbg:batman_adv bat0 batadv_dat_select_candidates(): IP=10.204.32.1 hash(IP)=48902
0.757 batadv:batadv_dbg:batman_adv bat0 dat_select_candidates() 0: selected fe:2c:91:68:29:2b addr=48977 dist=65460
1.178 batadv:batadv_dbg:batman_adv bat0 dat_select_candidates() 1: selected fe:81:ab:c5:e3:03 addr=49181 dist=65256
1.809 batadv:batadv_dbg:batman_adv bat0 dat_select_candidates() 2: selected 66:25:a7:48:37:fb addr=49328 dist=65109
1.828 batadv:batadv_dbg:batman_adv bat0 DHT_SEND for 10.204.32.1
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
CONFIG_BATMAN_ADV_DEBUGFS is disabled by default because debugfs is not
supported for batman-adv interfaces in any non-default netns. Any remaining
users of this interface should still be informed about the deprecation and
the generic netlink alternative.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The hardif_neigh refcounter is to be decreased by the queued work and
currently is never decreased if the queue_work() call fails.
Fix by checking the queue_work() return value and decrease refcount
if necessary.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The backbone_gw refcounter is to be decreased by the queued work and
currently is never decreased if the queue_work() call fails.
Fix by checking the queue_work() return value and decrease refcount
if necessary.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_tvlv_handler_register is responsible for adding new
tvlv_handler to the handler_list. It first checks whether the entry
already is in the list or not. If it is, then the creation of a new entry
is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: ef26157747 ("batman-adv: tvlv - basic infrastructure")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_tt_global_orig_entry_add is responsible for adding new
tt_orig_list_entry to the orig_list. It first checks whether the entry
already is in the list or not. If it is, then the creation of a new entry
is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: d657e621a0 ("batman-adv: add reference counting for type batadv_tt_orig_list_entry")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_softif_vlan_get is responsible for adding new
softif_vlan to the softif_vlan_list. It first checks whether the entry
already is in the list or not. If it is, then the creation of a new entry
is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: 5d2c05b213 ("batman-adv: add per VLAN interface attribute framework")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_nc_get_nc_node is responsible for adding new nc_nodes
to the in_coding_list and out_coding_list. It first checks whether the
entry already is in the list or not. If it is, then the creation of a new
entry is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: d56b1705e2 ("batman-adv: network coding - detect coding nodes and remove these after timeout")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_gw_node_add is responsible for adding new gw_node to
the gateway_list. It is expecting that the caller already checked that
there is not already an entry with the same key or not.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The per hardif sysfs file "batman_adv/elp_interval" is using the generic
functions to store/show uint values. The helper __batadv_store_uint_attr
requires the softif net_device as parameter to print the resulting change
as info text when the users writes to this file. It uses the helper
function batadv_info to add it at the same time to the kernel ring buffer
and to the batman-adv debug log (when CONFIG_BATMAN_ADV_DEBUG is enabled).
The function batadv_info requires as first parameter the batman-adv softif
net_device. This parameter is then used to find the private buffer which
contains the debug log for this batman-adv interface. But
batadv_store_throughput_override used as first argument the slave
net_device. This slave device doesn't have the batadv_priv private data
which is access by batadv_info.
Writing to this file with CONFIG_BATMAN_ADV_DEBUG enabled can either lead
to a segfault or to memory corruption.
Fixes: 0744ff8fa8 ("batman-adv: Add hard_iface specific sysfs wrapper macros for UINT")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The per hardif sysfs file "batman_adv/throughput_override" prints the
resulting change as info text when the users writes to this file. It uses
the helper function batadv_info to add it at the same time to the kernel
ring buffer and to the batman-adv debug log (when CONFIG_BATMAN_ADV_DEBUG
is enabled).
The function batadv_info requires as first parameter the batman-adv softif
net_device. This parameter is then used to find the private buffer which
contains the debug log for this batman-adv interface. But
batadv_store_throughput_override used as first argument the slave
net_device. This slave device doesn't have the batadv_priv private data
which is access by batadv_info.
Writing to this file with CONFIG_BATMAN_ADV_DEBUG enabled can either lead
to a segfault or to memory corruption.
Fixes: 0b5ecc6811 ("batman-adv: add throughput override attribute to hard_ifaces")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The probe ELPs for WiFi interfaces are expanded to contain at least
BATADV_ELP_MIN_PROBE_SIZE bytes. This is usually a lot more than the
number of bytes which the template ELP packet requires.
These extra padding bytes were not initialized and thus could contain data
which were previously stored at the same location. It is therefore required
to set it to some predefined or random values to avoid leaking private
information from the system transmitting these kind of packets.
Fixes: e4623c913508 ("batman-adv: Avoid probe ELP information leak")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
- Don't call BATMAN_V experimental in Kconfig anymore, by Sven Eckelmann
- Enable DAT by default at compile time, by Antonio Quartulli
- Remove obsolete default n in Kconfig, by Sven Eckelmann
- Fix checkpatch spelling errors, by Sven Eckelmann
- Unify header guards style, by Sven Eckelmann
- Consolidate batadv_purge_orig functions, by Sven Eckelmann
- Replace type define with proper typedef, by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=dmZo
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20180717' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- Don't call BATMAN_V experimental in Kconfig anymore, by Sven Eckelmann
- Enable DAT by default at compile time, by Antonio Quartulli
- Remove obsolete default n in Kconfig, by Sven Eckelmann
- Fix checkpatch spelling errors, by Sven Eckelmann
- Unify header guards style, by Sven Eckelmann
- Consolidate batadv_purge_orig functions, by Sven Eckelmann
- Replace type define with proper typedef, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The #define for batadv_dat_addr_t is doing nothing else than giving u16 a
new typename. But C already has the special keyword "typedef" which is also
better supported by kernel-doc.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The single line function batadv_purge_orig_ref has no function beside
providing the name used by other source files. This can also be done
simpler by just renaming _batadv_purge_orig to batadv_purge_orig_ref.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
All other include guards in batman-adv use the style:
* _NET_BATMAN_ADV_$(FILENAME)_
* uppercase only
* "." & "-" replaced with "_"
Use this also in the B.A.T.M.A.N. IV/V OGM implementation headers.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
commit a2d4df9b673c ("spelling.txt: add more spellings to spelling.txt")
introduced the spellcheck of "cache" for checkpatch.pl.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The "default n" is the default value for any bool or tristate Kconfig
setting. It is therefore not necessary to add it to a config entry.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
DAT (Distributed ARP Table) has been enabled by default
in the out-of-tree batman-adv kernel module for several
years already.
It can now be enabled in the kernel too.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The Kconfig option BATMAN_ADV_BATMAN_V is now enabled by default when the
BATMAN_ADV is enabled. A feature which is enabled by default for a module
should not be considered experimental.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
When a (broken) node wrongly sends multicast TT entries with a ROAM
flag then this causes any receiving node to drop all entries for the
same multicast MAC address announced by other nodes, leading to
packet loss.
Fix this DoS vector by only storing TT sync flags. For multicast TT
non-sync'ing flag bits like ROAM are unused so far anyway.
Fixes: 1d8ab8d3c1 ("batman-adv: Modified forwarding behaviour for multicast packets")
Reported-by: Leonardo Mörlein <me@irrelefant.net>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Since commit 54e22f265e ("batman-adv: fix TT sync flag inconsistencies")
TT sync flags and TT non-sync'd flags are supposed to be stored
separately.
The previous patch missed to apply this separation on a TT entry with
only a single TT orig entry.
This is a minor fix because with only a single TT orig entry the DDoS
issue the former patch solves does not apply.
Fixes: 54e22f265e ("batman-adv: fix TT sync flag inconsistencies")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batman-adv is creating special debugfs directories in the init
net_namespace for each created soft-interface (batadv net_device). But it
is possible to rename a net_device to a completely different name then the
original one.
It can therefore happen that a user registers a new batadv net_device with
the name "bat0". batman-adv is then also adding a new directory under
$debugfs/batman-adv/ with the name "wlan0".
The user then decides to rename this device to "bat1" and registers a
different batadv device with the name "bat0". batman-adv will then try to
create a directory with the name "bat0" under $debugfs/batman-adv/ again.
But there already exists one with this name under this path and thus this
fails. batman-adv will detect a problem and rollback the registering of
this device.
batman-adv must therefore take care of renaming the debugfs directories for
soft-interfaces whenever it detects such a net_device rename.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batman-adv is creating special debugfs directories in the init
net_namespace for each valid hard-interface (net_device). But it is
possible to rename a net_device to a completely different name then the
original one.
It can therefore happen that a user registers a new net_device which gets
the name "wlan0" assigned by default. batman-adv is also adding a new
directory under $debugfs/batman-adv/ with the name "wlan0".
The user then decides to rename this device to "wl_pri" and registers a
different device. The kernel may now decide to use the name "wlan0" again
for this new device. batman-adv will detect it as a valid net_device and
tries to create a directory with the name "wlan0" under
$debugfs/batman-adv/. But there already exists one with this name under
this path and thus this fails. batman-adv will detect a problem and
rollback the registering of this device.
batman-adv must therefore take care of renaming the debugfs directories
for hard-interfaces whenever it detects such a net_device rename.
Fixes: 5bc7c1eb44 ("batman-adv: add debugfs structure for information per interface")
Reported-by: John Soros <sorosj@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
A reference for the best gateway is taken when the list of gateways in the
mesh is sent via netlink. This is necessary to check whether the currently
dumped entry is the currently selected gateway or not. This information is
then transferred as flag BATADV_ATTR_FLAG_BEST.
After the comparison of the current entry is done,
batadv_v_gw_dump_entry() has to decrease the reference counter again.
Otherwise the reference will be held and thus prevents a proper shutdown of
the batman-adv interfaces (and some of the interfaces enslaved in it).
Fixes: b71bb6f924 ("batman-adv: add B.A.T.M.A.N. V bat_gw_dump implementations")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
A reference for the best gateway is taken when the list of gateways in the
mesh is sent via netlink. This is necessary to check whether the currently
dumped entry is the currently selected gateway or not. This information is
then transferred as flag BATADV_ATTR_FLAG_BEST.
After the comparison of the current entry is done,
batadv_iv_gw_dump_entry() has to decrease the reference counter again.
Otherwise the reference will be held and thus prevents a proper shutdown of
the batman-adv interfaces (and some of the interfaces enslaved in it).
Fixes: efb766af06 ("batman-adv: add B.A.T.M.A.N. IV bat_gw_dump implementations")
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Tested-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
random_ether_addr is a #define for eth_random_addr which is
generally preferred in kernel code by ~3:1
Convert the uses of random_ether_addr to enable removing the #define
Miscellanea:
o Convert &vfmac[0] to equivalent vfmac and avoid unnecessary line wrap
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Virtual interface drivers such as tun / tap interfaces, VLAN, etc tend
to initialize the interface throughput with some value for the sake of
having a throughput number to export via ethtool. This exported
throughput leaves batman-adv to conclude the interface throughput is
genuine (reflecting reality), thus no measurements are necessary.
Based on the observation that those interface types also tend to set
the link auto-negotiation to 'off', batman-adv shall check this
setting to differentiate between genuine link throughput information
and placeholders installed by virtual interfaces.
The "default throughput" setting exported via sysfs still allows to
configure the batman-adv throughput for the interface, thus disabling
the measurements.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
A translation table TVLV changset sent with an OGM consists
of a number of headers (one per VLAN) plus the changeset
itself (addition and/or deletion of entries).
The per-VLAN headers are used by OGM recipients for consistency
checks. Said consistency check might determine that a full
translation table request is needed to restore consistency. If
the TT sender adds per-VLAN headers of empty VLANs into the OGM,
recipients are led to believe to have reached an inconsistent
state and thus request a full table update. The full table does
not contain empty VLANs (due to missing entries) the cycle
restarts when the next OGM is issued.
Consequently, when the translation table TVLV headers are
composed, empty VLANs are to be excluded.
Fixes: 21a57f6e7a3b ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The previous TT sync fix so far only fixed TT responses issued by the
target node directly. So far, TT responses issued by intermediate nodes
still lead to the wrong flags being added, leading to CRC mismatches.
This behaviour was observed at Freifunk Hannover in a 800 nodes setup
where a considerable amount of nodes were still infected with 'WI'
TT flags even with (most) nodes having the previous TT sync fix applied.
I was able to reproduce the issue with intermediate TT responses in a
four node test setup and this patch fixes this issue by ensuring to
use the per originator instead of the summarized, OR'd ones.
Fixes: e9c00136a4 ("batman-adv: fix tt_global_entries flags update")
Reported-by: Leonardo Mörlein <me@irrelefant.net>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The functions batadv_tt_prepare_tvlv_local_data and
batadv_tt_prepare_tvlv_global_data are responsible for preparing a buffer
which can be used to store the TVLV container for TT and add the VLAN
information to it.
This will be done in three phases:
1. count the number of VLANs and their entries
2. allocate the buffer using the counters from the previous step and limits
from the caller (parameter tt_len)
3. insert the VLAN information to the buffer
The step 1 and 3 operate on a list which contains the VLANs. The access to
these lists must be protected with an appropriate lock or otherwise they
might operate on on different entries. This could for example happen when
another context is adding VLAN entries to this list.
This could lead to a buffer overflow in these functions when enough entries
were added between step 1 and 3 to the VLAN lists that the buffer room for
the entries (*tt_change) is smaller then the now required extra buffer for
new VLAN entries.
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
[sven@narfation.org: fixed alignment]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The debug_dir variable in the main structures is only accessed when
CONFIG_BATMAN_ADV_DEBUGFS is enabled. It can be dropped to potentially save
some bytes of memory.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Using the bool type for structure member is considered inappropriate [1]
for the kernel. Its size is not well defined (but usually 1 byte but maybe
also 4 byte).
[1] https://lkml.org/lkml/2017/11/21/384
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Instead of disabling multicast optimizations mesh-wide once a node with
no multicast optimizations capabilities joins the mesh, do the
following:
Just insert such nodes into the WANT_ALL_IPV4/IPV6 lists. This is
sufficient to avoid multicast packet loss to such unsupportive nodes.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
All tools which were known to the batman-adv development team are
supporting the batman-adv netlink interface since a while. Also debugfs is
not supported for batman-adv interfaces in any non-default netns. Thus
disabling CONFIG_BATMAN_ADV_DEBUGFS by default should not cause problems on
most systems. It is still possible to enable it in case it is still
required in a specific setup.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
In the case where hard_iface is NULL, the error path may pass a null
pointer to batadv_hardif_put causing a null pointer dereference error.
Avoid this by only calling the function if hard_iface not null.
Detected by CoverityScan, CID#1466456 ("Explicit null dereferenced")
Fixes: 53dd9a68ba ("batman-adv: add multicast flags netlink support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Minor conflicts in drivers/net/ethernet/mellanox/mlx5/core/en_rep.c,
we had some overlapping changes:
1) In 'net' MLX5E_PARAMS_LOG_{SQ,RQ}_SIZE -->
MLX5E_REP_PARAMS_LOG_{SQ,RQ}_SIZE
2) In 'net-next' params->log_rq_size is renamed to be
params->log_rq_mtu_frames.
3) In 'net-next' params->hard_mtu is added.
Signed-off-by: David S. Miller <davem@davemloft.net>
DHCP connectivity issues can currently occur if the following conditions
are met:
1) A DHCP packet from a client to a server
2) This packet has a multicast destination
3) This destination has a matching entry in the translation table
(FF:FF:FF:FF:FF:FF for IPv4, 33:33:00:01:00:02/33:33:00:01:00:03
for IPv6)
4) The orig-node determined by TT for the multicast destination
does not match the orig-node determined by best-gateway-selection
In this case the DHCP packet will be dropped.
The "gateway-out-of-range" check is supposed to only be applied to
unicasted DHCP packets to a specific DHCP server.
In that case dropping the the unicasted frame forces the client to
retry via a broadcasted one, but now directed to the new best
gateway.
A DHCP packet with broadcast/multicast destination is already ensured to
always be delivered to the best gateway. Dropping a multicasted
DHCP packet here will only prevent completing DHCP as there is no
other fallback.
So far, it seems the unicast check was implicitly performed by
expecting the batadv_transtable_search() to return NULL for multicast
destinations. However, a multicast address could have always ended up in
the translation table and in fact is now common.
To fix this potential loss of a DHCP client-to-server packet to a
multicast address this patch adds an explicit multicast destination
check to reliably bail out of the gateway-out-of-range check for such
destinations.
The issue and fix were tested in the following three node setup:
- Line topology, A-B-C
- A: gateway client, DHCP client
- B: gateway server, hop-penalty increased: 30->60, DHCP server
- C: gateway server, code modifications to announce FF:FF:FF:FF:FF:FF
Without this patch, A would never transmit its DHCP Discover packet
due to an always "out-of-range" condition. With this patch,
a full DHCP handshake between A and B was possible again.
Fixes: be7af5cf9c ("batman-adv: refactoring gateway handling code")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Sven Eckelmann
David S. Miller
Simon Wunderlich
Marek Lindner
Antonio Quartulli
Linus Lüssing
Joe Perches
Luc Van Oostenryck
Colin Ian King