This patch adds the DT node for the uniperif reader
IP block found on STiH407 family silicon.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
This patch adds the DT nodes for the uniperif player
IP blocks found on STiH407 family silicon.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
This patch adds the dt node for the internal audio
codec IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
This patch adds the pinctrl config for the spidf out
pins used by the sasg codec IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
This patch adds the pinctrl config for the i2s_in pins
used by the uniperif reader IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
This patch adds the pinctrl config for the i2s_out pins
used by the uniperif player IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
These nodes are required to get the fdma driver working
on STiH407 based silicon.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Add the hva (multi-format video encoder for STMicroelectronics SoC)
dt nodes for the hva device, defining register address, interrupt
and clock.
Signed-off-by: Jean-Christophe TROTIN <jean-christophe.trotin@st.com>
This allows to make the board boot even if clock handling
by all drivers is not properly done.
Reported-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch allows to use second parameter to the gpio
specifier, which is used to specify whether the gpio is
active high or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch allows to use second parameter to the gpio
specifier, which is used to specify whether the gpio is
active high or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
- Remove useless gpio-cells
- Update second parameter by using GPIO_ACTIVE_HIGH/LOW
instead of hardcoded value
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
- Remove useless gpio-cells
- Update second parameter by using GPIO_ACTIVE_HIGH/LOW
instead of hardcoded value
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch allows to use second parameter to the gpio
specifier, which is used to specify whether the gpio is
active high or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
B2260 board is the STMicroelectronics 96Board
based on STiH410 soc :
- 1GB DDR
- On-Board USB combo WiFi/Bluetooth RTL8723BU
with PCB soldered antenna
- Ethernet 1000-BaseT
- Sata
- HDMI
- 2 x USB2 type A
- micro USB2 type AB
- SD card slot
- High speed connector (SD/I2C/USB interfaces)
- Slow speed connector (UART/I2C/GPIO/SPI/PCM interfaces)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Despite ST AHCI version = 1.3, reading HOST_PORTS_IMPL
returns 0. So force HOST_PORTS_IMPL to 1 by using
ports-implemented DT property.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
On 96board, we can't reuse rgmii1-mdio as the pin pio1 3
( mdint ) is dedicated for user led green 1. So create
rgmii1_mdio_1 for 96board on which only mdio and mdc pins
are useful.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Due to 96board which uses mmc0 node for SD card, the non-removable
property must be moved from STiH407-family to board file for B2120
and B2199 boards.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Add missing pin muxing for I2C2 alternate 2. This
i2c2 pin muxing is dedicated for 96board high speed
expansion connector.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
[Lee: Correct spacing between nodes]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
[Lee: Changed node name and added the unit address]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
* x86 nested virt tweak and OOPS fix
* Simplify pvclock code (vdso bits acked by Andy Lutomirski).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXpKOnAAoJEL/70l94x66D5z4H/R2660Vy3brQrI8lGxCtkXJt
AVe8PwI8nDfYJ/UkMZ2KcHPSvy+sHW2ydaZXYNqXHVBeTaUxiPW9rTgK61ebypGL
1tPOgJ3kGZF6XEdAz6gS8LniNFc+D3W6Y6sRylkEsqPj39/hxe7QMoOMSCQ9imbW
WMIx7/81i1EMw6oi+9FVtq+yHCpvyfFnD8t1TDsYWOReVn1J15SxbEs4Ih+hBMLz
HZ5DEjp9cAmzeR7GLje5eH1t6TEEoNb1MNgFWuscoAsDf8D9DKqRB9s0hC+TLFYn
oZbGSqjQwu3/VMblgedinH6X9MTm8V0zW29ToGnDcoO00AUmdlNmXSaZUhvT/Rs=
=H5cD
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
- ARM bugfix and MSI injection support
- x86 nested virt tweak and OOPS fix
- Simplify pvclock code (vdso bits acked by Andy Lutomirski).
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
nvmx: mark ept single context invalidation as supported
nvmx: remove comment about missing nested vpid support
KVM: lapic: fix access preemption timer stuff even if kernel_irqchip=off
KVM: documentation: fix KVM_CAP_X2APIC_API information
x86: vdso: use __pvclock_read_cycles
pvclock: introduce seqcount-like API
arm64: KVM: Set cpsr before spsr on fault injection
KVM: arm: vgic-irqfd: Workaround changing kvm_set_routing_entry prototype
KVM: arm/arm64: Enable MSI routing
KVM: arm/arm64: Enable irqchip routing
KVM: Move kvm_setup_default/empty_irq_routing declaration in arch specific header
KVM: irqchip: Convey devid to kvm_set_msi
KVM: Add devid in kvm_kernel_irq_routing_entry
KVM: api: Pass the devid in the msi routing entry
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.8. Also includes is a
minor SSB cleanup as SSB code traditionally is merged through the MIPS
tree:
ATH25:
- MIPS: Add default configuration for ath25
Boot:
- For zboot, copy appended dtb to the end of the kernel
- store the appended dtb address in a variable
BPF:
- Fix off by one error in offset allocation
Cobalt code:
- Fix typos
Core code:
- debugfs_create_file returns NULL on error, so don't use IS_ERR for
testing for errors.
- Fix double locking issue in RM7000 S-cache code. This would only
affect RM7000 ARC systems on reboot.
- Fix page table corruption on THP permission changes.
- Use compat_sys_keyctl for 32 bit userspace on 64 bit kernels.
David says, there are no compatibility issues raised by this fix.
- Move some signal code around.
- Rewrite r4k count/compare clockevent device registration such that
min_delta_ticks/max_delta_ticks files are guaranteed to be
initialized.
- Only register r4k count/compare as clockevent device if we can
assume the clock to be constant.
- Fix MSA asm warnings in control reg accessors
- uasm and tlbex fixes and tweaking.
- Print segment physical address when EU=1.
- Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO.
- CP: Allow booting by VP other than VP 0
- Cache handling fixes and optimizations for r4k class caches
- Add hotplug support for R6 processors
- Cleanup hotplug bits in kconfig
- traps: return correct si code for accessing nonmapped addresses
- Remove cpu_has_safe_index_cacheops
Lantiq:
- Register IRQ handler for virtual IRQ number
- Fix EIU interrupt loading code
- Use the real EXIN count
- Fix build error.
Loongson 3:
- Increase HPET_MIN_PROG_DELTA and decrease HPET_MIN_CYCLES
Octeon:
- Delete built-in DTB pruning code for D-Link DSR-1000N.
- Clean up GPIO definitions in dlink_dsr-1000n.dts.
- Add more LEDs to the DSR-100n DTS
- Fix off by one in octeon_irq_gpio_map()
- Typo fixes
- Enable SATA by default in cavium_octeon_defconfig
- Support readq/writeq()
- Remove forced mappings of USB interrupts.
- Ensure DMA descriptors are always in the low 4GB
- Improve USB reset code for OCTEON II.
Pistachio:
- Add maintainers entry for pistachio SoC Support
- Remove plat_setup_iocoherency
Ralink:
- Fix pwm UART in spis group pinmux.
SSB:
- Change bare unsigned to unsigned int to suit coding style
Tools:
- Fix reloc tool compiler warnings.
Other:
- Delete use of ARCH_WANT_OPTIONAL_GPIOLIB"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (61 commits)
MIPS: mm: Fix definition of R6 cache instruction
MIPS: tools: Fix relocs tool compiler warnings
MIPS: Cobalt: Fix typo
MIPS: Octeon: Fix typo
MIPS: Lantiq: Fix build failure
MIPS: Use CPHYSADDR to implement mips32 __pa
MIPS: Octeon: Dlink_dsr-1000n.dts: add more leds.
MIPS: Octeon: Clean up GPIO definitions in dlink_dsr-1000n.dts.
MIPS: Octeon: Delete built-in DTB pruning code for D-Link DSR-1000N.
MIPS: store the appended dtb address in a variable
MIPS: ZBOOT: copy appended dtb to the end of the kernel
MIPS: ralink: fix spis group pinmux
MIPS: Factor o32 specific code into signal_o32.c
MIPS: non-exec stack & heap when non-exec PT_GNU_STACK is present
MIPS: Use per-mm page to execute branch delay slot instructions
MIPS: Modify error handling
MIPS: c-r4k: Use SMP calls for CM indexed cache ops
MIPS: c-r4k: Avoid small flush_icache_range SMP calls
MIPS: c-r4k: Local flush_icache_range cache op override
MIPS: c-r4k: Split r4k_flush_kernel_vmap_range()
...
Pull x86 fixes from Ingo Molnar:
"Two fixes and a cleanup-fix, to the syscall entry code and to ptrace"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/syscalls/64: Add compat_sys_keyctl for 32-bit userspace
x86/ptrace: Stop setting TS_COMPAT in ptrace code
x86/vdso: Error out if the vDSO isn't a valid DSO
support for the J-Core J2 processor, an open source synthesizable
reimplementation of the SH-2 ISA, resolve a longstanding sigcontext
ABI mismatch issue, and fix various bugs including nommu-specific
issues and minor regressions introduced in 4.6.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJXpQweAAoJELcQ+SIFb8Ha2vgH/Rm3YTHEgGeQhRvBle8DTPNv
l9xBCQ6UMVb9T8C5nyP0jdioAVDQr7gh7sv2c7inIjN8hQh16DXFtNV8X6G3b0jv
OC0+rBmcYjpO7gGC/L2sRE8ghuNpoIBJFojZy6bwOIvpF6EDMAZ9bAU/VFbY28so
nCUdEo0gAmrdqGyHRfEJke7D7AKPvpAnN/cmRcvNQPhkkzKjRSNg5rHLthmvAKyp
1ChASb3YYPTgOY09izD8JUp4rk7v7q2smpgfeZfGQhIN/w6QKpv5OIqe+vrm1iKU
B6q5gBHS7Y2VYilp1zKQedLM9ZthH6rnpkB25RzyH655uTwf//6ihyP3kEwlPkc=
=wwNa
-----END PGP SIGNATURE-----
Merge tag 'sh-for-4.8' of git://git.libc.org/linux-sh
Pull arch/sh updates from Rich Felker:
"These changes improve device tree support (including builtin DTB), add
support for the J-Core J2 processor, an open source synthesizable
reimplementation of the SH-2 ISA, resolve a longstanding sigcontext
ABI mismatch issue, and fix various bugs including nommu-specific
issues and minor regressions introduced in 4.6.
The J-Core arch support is included here but to be usable it needs
drivers that are waiting on approval/inclusion from their subsystem
maintainers"
* tag 'sh-for-4.8' of git://git.libc.org/linux-sh: (23 commits)
sh: add device tree source for J2 FPGA on Mimas v2 board
sh: add defconfig for J-Core J2
sh: use common clock framework with device tree boards
sh: system call wire up
sh: Delete unnecessary checks before the function call "mempool_destroy"
sh: do not perform IPI-based cache flush except on boards that need it
sh: add SMP support for J2
sh: SMP support for SH2 entry.S
sh: add working futex atomic ops on userspace addresses for smp
sh: add J2 atomics using the cas.l instruction
sh: add AT_HWCAP flag for J-Core cas.l instruction
sh: add support for J-Core J2 processor
sh: fix build regression with CONFIG_OF && !CONFIG_OF_FLATTREE
sh: allow clocksource drivers to register sched_clock backends
sh: make heartbeat driver explicitly non-modular
sh: make board-secureedge5410 explicitly non-modular
sh: make mm/asids-debugfs explicitly non-modular
sh: make time.c explicitly non-modular
sh: fix futex/robust_list on nommu models
sh: disable aliased page logic on NOMMU models
...
- Fix HugeTLB leak due to CoW and PTE_RDONLY mismatch
- Avoid accessing unmapped FDT fields when checking validity
- Correctly account for vDSO AUX entry in ARCH_DLINFO
- Fix kallsyms with absolute expressions in linker script
- Kill unnecessary symbol-based relocs in vmlinux
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJXpFZ5AAoJELescNyEwWM0PI4IALsTuHRzClOSMDLiqMUj8t+5
WNAcqybxAjCOVxAHckhweju++TeJBxcRH1nvBoNwiHIdHTv4fq1TZ3PeEq9kWMg5
JbKjYjvd9dW8k6LXMya8iXCYtG3kzbNejkNpOTVebC86yvas1IiEjNb/ztPdhJeM
HBSOkhfk8RcskfNxhuscZzGXbbdH9/R+XSTNRHN/RwCZH8PlInmduD9BbMvDhZyP
NLFonD2IgQ4as1kYG/HdIcw0BamHiURjd043+gyoqMvm7JjPksRzlQnr91SMkX17
LykXjHYPi2Me3aTrZ1NtkUNd5FHLHZ6/b9Wg6nA19d5KWkd3ER9uSJqGxkkbnt0=
=dtGK
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- fix HugeTLB leak due to CoW and PTE_RDONLY mismatch
- avoid accessing unmapped FDT fields when checking validity
- correctly account for vDSO AUX entry in ARCH_DLINFO
- fix kallsyms with absolute expressions in linker script
- kill unnecessary symbol-based relocs in vmlinux
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix copy-on-write referencing in HugeTLB
arm64: mm: avoid fdt_check_header() before the FDT is fully mapped
arm64: Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO
arm64: relocatable: suppress R_AARCH64_ABS64 relocations in vmlinux
arm64: vmlinux.lds: make __rela_offset and __dynsym_offset ABSOLUTE
- Prevent the low-level assembly hibernate code on x86-64 from
referring to __PAGE_OFFSET directly as a symbol which doesn't work
when the kernel identity mapping base is randomized, in which case
__PAGE_OFFSET is a variable (Rafael Wysocki).
- Avoid selecting CPU_FREQ_STAT by default as the statistics are not
required for proper cpufreq operation (Borislav Petkov).
- Add Skylake-X and Broadwell-X IDs to the intel_pstate's list of
processors where out-of-band (OBB) control of P-states is possible
and if that is in use, intel_pstate should not attempt to manage
P-states (Srinivas Pandruvada).
- Drop some unnecessary checks from the wakeup IRQ handling code in
the PM core (Markus Elfring).
- Reduce the number operating performance point (OPP) lookups in
one of the OPP framework's helper functions (Jisheng Zhang).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=WvPB
-----END PGP SIGNATURE-----
Merge tag 'pm-extra-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"A few more fixes and cleanups in the x86-64 low-level hibernation
code, PM core, cpufreq (Kconfig and intel_pstate), and the operating
points framework.
Specifics:
- Prevent the low-level assembly hibernate code on x86-64 from
referring to __PAGE_OFFSET directly as a symbol which doesn't work
when the kernel identity mapping base is randomized, in which case
__PAGE_OFFSET is a variable (Rafael Wysocki).
- Avoid selecting CPU_FREQ_STAT by default as the statistics are not
required for proper cpufreq operation (Borislav Petkov).
- Add Skylake-X and Broadwell-X IDs to the intel_pstate's list of
processors where out-of-band (OBB) control of P-states is possible
and if that is in use, intel_pstate should not attempt to manage
P-states (Srinivas Pandruvada).
- Drop some unnecessary checks from the wakeup IRQ handling code in
the PM core (Markus Elfring).
- Reduce the number operating performance point (OPP) lookups in one
of the OPP framework's helper functions (Jisheng Zhang)"
* tag 'pm-extra-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
x86/power/64: Do not refer to __PAGE_OFFSET from assembly code
cpufreq: Do not default-yes CPU_FREQ_STAT
cpufreq: intel_pstate: Add more out-of-band IDs
PM / OPP: optimize dev_pm_opp_set_rate() performance a bit
PM-wakeup: Delete unnecessary checks before three function calls
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup rtc-cmos,
rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after shutdown for QNAP
TS-41x
- s3c: clock fixes
-----BEGIN PGP SIGNATURE-----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=rpGB
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"RTC for 4.8
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup
rtc-cmos, rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after
shutdown for QNAP TS-41x
- s3c: clock fixes"
* tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (65 commits)
rtc: rv8803: Clear V1F when setting the time
rtc: rv8803: Stop the clock while setting the time
rtc: rv8803: Always apply the I²C workaround
rtc: rv8803: Fix read day of week
rtc: rv8803: Remove the check for valid time
rtc: rv8803: Kconfig: Indicate rx8900 support
rtc: asm9260: remove .owner field for driver
rtc: at91sam9: Fix missing spin_lock_init()
rtc: m41t80: add suspend handlers for alarm IRQ
rtc: m41t80: make it a real error message
rtc: pcf85063: Add support for the PCF85063A device
rtc: pcf85063: fix year range
rtc: hym8563: in .read_alarm set .tm_sec to 0 to signal minute accuracy
rtc: explicitly set tm_sec = 0 for drivers with minute accurancy
rtc: s3c: Add s3c_rtc_{enable/disable}_clk in s3c_rtc_setfreq()
rtc: s3c: Remove unnecessary call to disable already disabled clock
rtc: abx80x: use devm_add_action_or_reset()
rtc: m41t80: use devm_add_action_or_reset()
rtc: fix a typo and reduce three empty lines to one
rtc: s35390a: improve two comments in .set_alarm
...
* pm-sleep:
x86/power/64: Do not refer to __PAGE_OFFSET from assembly code
* pm-cpufreq:
cpufreq: Do not default-yes CPU_FREQ_STAT
cpufreq: intel_pstate: Add more out-of-band IDs
* pm-core:
PM-wakeup: Delete unnecessary checks before three function calls
* pm-opp:
PM / OPP: optimize dev_pm_opp_set_rate() performance a bit
Fixes:
- Fix early access to cpu_spec relocation from Benjamin Herrenschmidt
- Fix incorrect event codes in power9-event-list from Madhavan Srinivasan
- Move register_process_table() out of ppc_md from Michael Ellerman
Use jump_label for [cpu|mmu]_has_feature() from Aneesh Kumar K.V, Kevin Hao and Michael Ellerman:
- Add mmu_early_init_devtree() from Michael Ellerman
- Move disable_radix handling into mmu_early_init_devtree() from Michael Ellerman
- Do hash device tree scanning earlier from Michael Ellerman
- Do radix device tree scanning earlier from Michael Ellerman
- Do feature patching before MMU init from Michael Ellerman
- Check features don't change after patching from Michael Ellerman
- Make MMU_FTR_RADIX a MMU family feature from Aneesh Kumar K.V
- Convert mmu_has_feature() to returning bool from Michael Ellerman
- Convert cpu_has_feature() to returning bool from Michael Ellerman
- Define radix_enabled() in one place & use static inline from Michael Ellerman
- Add early_[cpu|mmu]_has_feature() from Michael Ellerman
- Convert early cpu/mmu feature check to use the new helpers from Aneesh Kumar K.V
- jump_label: Make it possible for arches to invoke jump_label_init() earlier from Kevin Hao
- Call jump_label_init() in apply_feature_fixups() from Aneesh Kumar K.V
- Remove mfvtb() from Kevin Hao
- Move cpu_has_feature() to a separate file from Kevin Hao
- Add kconfig option to use jump labels for cpu/mmu_has_feature() from Michael Ellerman
- Add option to use jump label for cpu_has_feature() from Kevin Hao
- Add option to use jump label for mmu_has_feature() from Kevin Hao
- Catch usage of cpu/mmu_has_feature() before jump label init from Aneesh Kumar K.V
- Annotate jump label assembly from Michael Ellerman
TLB flush enhancements from Aneesh Kumar K.V:
- radix: Implement tlb mmu gather flush efficiently
- Add helper for finding SLBE LLP encoding
- Use hugetlb flush functions
- Drop multiple definition of mm_is_core_local
- radix: Add tlb flush of THP ptes
- radix: Rename function and drop unused arg
- radix/hugetlb: Add helper for finding page size
- hugetlb: Add flush_hugetlb_tlb_range
- remove flush_tlb_page_nohash
Add new ptrace regsets from Anshuman Khandual and Simon Guo:
- elf: Add powerpc specific core note sections
- Add the function flush_tmregs_to_thread
- Enable in transaction NT_PRFPREG ptrace requests
- Enable in transaction NT_PPC_VMX ptrace requests
- Enable in transaction NT_PPC_VSX ptrace requests
- Adapt gpr32_get, gpr32_set functions for transaction
- Enable support for NT_PPC_CGPR
- Enable support for NT_PPC_CFPR
- Enable support for NT_PPC_CVMX
- Enable support for NT_PPC_CVSX
- Enable support for TM SPR state
- Enable NT_PPC_TM_CTAR, NT_PPC_TM_CPPR, NT_PPC_TM_CDSCR
- Enable support for NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR
- Enable support for EBB registers
- Enable support for Performance Monitor registers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Q8E
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"These were delayed for various reasons, so I let them sit in next a
bit longer, rather than including them in my first pull request.
Fixes:
- Fix early access to cpu_spec relocation from Benjamin Herrenschmidt
- Fix incorrect event codes in power9-event-list from Madhavan Srinivasan
- Move register_process_table() out of ppc_md from Michael Ellerman
Use jump_label use for [cpu|mmu]_has_feature():
- Add mmu_early_init_devtree() from Michael Ellerman
- Move disable_radix handling into mmu_early_init_devtree() from Michael Ellerman
- Do hash device tree scanning earlier from Michael Ellerman
- Do radix device tree scanning earlier from Michael Ellerman
- Do feature patching before MMU init from Michael Ellerman
- Check features don't change after patching from Michael Ellerman
- Make MMU_FTR_RADIX a MMU family feature from Aneesh Kumar K.V
- Convert mmu_has_feature() to returning bool from Michael Ellerman
- Convert cpu_has_feature() to returning bool from Michael Ellerman
- Define radix_enabled() in one place & use static inline from Michael Ellerman
- Add early_[cpu|mmu]_has_feature() from Michael Ellerman
- Convert early cpu/mmu feature check to use the new helpers from Aneesh Kumar K.V
- jump_label: Make it possible for arches to invoke jump_label_init() earlier from Kevin Hao
- Call jump_label_init() in apply_feature_fixups() from Aneesh Kumar K.V
- Remove mfvtb() from Kevin Hao
- Move cpu_has_feature() to a separate file from Kevin Hao
- Add kconfig option to use jump labels for cpu/mmu_has_feature() from Michael Ellerman
- Add option to use jump label for cpu_has_feature() from Kevin Hao
- Add option to use jump label for mmu_has_feature() from Kevin Hao
- Catch usage of cpu/mmu_has_feature() before jump label init from Aneesh Kumar K.V
- Annotate jump label assembly from Michael Ellerman
TLB flush enhancements from Aneesh Kumar K.V:
- radix: Implement tlb mmu gather flush efficiently
- Add helper for finding SLBE LLP encoding
- Use hugetlb flush functions
- Drop multiple definition of mm_is_core_local
- radix: Add tlb flush of THP ptes
- radix: Rename function and drop unused arg
- radix/hugetlb: Add helper for finding page size
- hugetlb: Add flush_hugetlb_tlb_range
- remove flush_tlb_page_nohash
Add new ptrace regsets from Anshuman Khandual and Simon Guo:
- elf: Add powerpc specific core note sections
- Add the function flush_tmregs_to_thread
- Enable in transaction NT_PRFPREG ptrace requests
- Enable in transaction NT_PPC_VMX ptrace requests
- Enable in transaction NT_PPC_VSX ptrace requests
- Adapt gpr32_get, gpr32_set functions for transaction
- Enable support for NT_PPC_CGPR
- Enable support for NT_PPC_CFPR
- Enable support for NT_PPC_CVMX
- Enable support for NT_PPC_CVSX
- Enable support for TM SPR state
- Enable NT_PPC_TM_CTAR, NT_PPC_TM_CPPR, NT_PPC_TM_CDSCR
- Enable support for NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR
- Enable support for EBB registers
- Enable support for Performance Monitor registers"
* tag 'powerpc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (48 commits)
powerpc/mm: Move register_process_table() out of ppc_md
powerpc/perf: Fix incorrect event codes in power9-event-list
powerpc/32: Fix early access to cpu_spec relocation
powerpc/ptrace: Enable support for Performance Monitor registers
powerpc/ptrace: Enable support for EBB registers
powerpc/ptrace: Enable support for NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR
powerpc/ptrace: Enable NT_PPC_TM_CTAR, NT_PPC_TM_CPPR, NT_PPC_TM_CDSCR
powerpc/ptrace: Enable support for TM SPR state
powerpc/ptrace: Enable support for NT_PPC_CVSX
powerpc/ptrace: Enable support for NT_PPC_CVMX
powerpc/ptrace: Enable support for NT_PPC_CFPR
powerpc/ptrace: Enable support for NT_PPC_CGPR
powerpc/ptrace: Adapt gpr32_get, gpr32_set functions for transaction
powerpc/ptrace: Enable in transaction NT_PPC_VSX ptrace requests
powerpc/ptrace: Enable in transaction NT_PPC_VMX ptrace requests
powerpc/ptrace: Enable in transaction NT_PRFPREG ptrace requests
powerpc/process: Add the function flush_tmregs_to_thread
elf: Add powerpc specific core note sections
powerpc/mm: remove flush_tlb_page_nohash
powerpc/mm/hugetlb: Add flush_hugetlb_tlb_range
...
Just a few minor fixes:
- Fix another incorrect inline asm register constraint, which has been
lying quietly for 5 and a half years before finally causing build
breakage during this merge window.
- Removal of duplicated KERN_INFO from Joe Perches.
- Typo fixes from Andrea Gelmini.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8ih8
-----END PGP SIGNATURE-----
Merge tag 'metag-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull metag architecture updates from James Hogan:
"Just a few minor fixes:
- Fix another incorrect inline asm register constraint, which has
been lying quietly for 5 and a half years before finally causing
build breakage during this merge window.
- Removal of duplicated KERN_INFO from Joe Perches
- Typo fixes from Andrea Gelmini"
* tag 'metag-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: Fix __cmpxchg_u32 asm constraint for CMP
metag: Remove duplicate KERN_<LEVEL> prefix
metag: Fix typos
This defconfig is intended not to be specific to a particular board;
it enables drivers for all currently-supported hardware, and should be
updated to include additional drivers as they are added.
Signed-off-by: Rich Felker <dalias@libc.org>
Enable common clk framework for DT-based boards and disable code that
depends on the legacy sh clk framework when common clk is enabled.
Once legacy drivers are converted over, the old code can be removed
entirely.
Signed-off-by: Rich Felker <dalias@libc.org>
The mempool_destroy() function tests whether its argument is NULL
and then returns immediately. Thus the test around the calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Rich Felker <dalias@libc.org>
Support is hooked up via a cpu start method specified in the device
tree, and also depends on DT nodes that describe the interfaces for
performing IPI and identifying which cpu execution is taking place on.
The currently used method is a form of spin table, where secondary
cpus are unblocked by writing to a special address.
Signed-off-by: Rich Felker <dalias@libc.org>
The SH2 version of entry.S uses global variables, which need to be
cpu-local in order to work with SMP. For ease of access from asm,
simply use arrays indexed by cpu number, and require the availability
of an address (mmio register or properly setup per-cpu memory) from
which the current cpu's index can be read.
Signed-off-by: Rich Felker <dalias@libc.org>
Peter Griffin
Jean-Christophe Trotin
Patrice Chotard
Lee Jones
Linus Torvalds
Rafael J. Wysocki
Rich Felker
Yoshinori Sato
Markus Elfring