In Test 9 of usbtest module, it is used for performing chapter 9 tests N
times. This patch adds to support getting bos descriptor test scenario for
USB 3.0.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB3503 driver had an incorrect depedency on REGMAP, instead of
REGMAP_I2C. This caused the build to fail since the necessary regmap
i2c pieces were not available.
Signed-off-by: Matthew Dawson <matthew@mjdsystems.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When transfer type is isochronous, the other bits (bits 5..2) of
bmAttributes in endpoint descriptor might not be set zero. So it's better
to use usb_endpoint_type routine to mask bmAttributes with
USB_ENDPOINT_XFERTYPE_MASK to judge the transfter type later.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the USB control request is allocated separately from
containing structure to prevent potential memory corruption on
non-cache-coherent systems.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the reported device-type on big-endian machines is the same as
on little-endian ones.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB Embedded High-speed Host Electrical Test (EHSET) defines the
SINGLE_STEP_SET_FEATURE test as follows:
1) The host enumerates the test device with VID:0x1A0A, PID:0x0108
2) The host sends the SETUP stage of a GetDescriptor(Device)
3) The device ACKs the request
4) The host issues SOFs for 15 seconds allowing the test operator to
raise the scope trigger just above the SOF voltage level
5) The host sends the IN packet
6) The device sends data in response, triggering the scope
7) The host sends an ACK in response to the data
This patch adds additional handling to the EHCI hub driver and allows
the EHSET driver to initiate this test mode by issuing a a SetFeature
request to the root hub with a Test Selector value of 0x06. From there
it mimics ehci_urb_enqueue() but separately submits QTDs for the
SETUP and DATA/STATUS stages in order to insert a delay in between.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[jackp@codeaurora.org: imported from commit c2084930 on codeaurora.org;
minor cleanup and updated author email]
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor so that register writes for configuration are only performed if
the device has a regmap provided and also register as a platform driver.
This allows the driver to be used to manage GPIO based control of the
device.
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are no software visible differences that I am aware of but in case
any are discovered allow the DTS to specify exactly which device is
present.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there is no runtime interface for changing modes this is probably
the most sensible default.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for supporting operation without an I2C control interface
factor out the I2C-specific parts of the probe routine from those that
don't do any register I/O.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will give access to the diagnostic infrastructure regmap has but
the main point is to support future refactoring.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the connect signal is pulled high then the device will start up meaning
that if we just pull it high on probe then the device will start running
prior to the configuration being written out. Fix this by pulling the GPIO
low when we reset and only pulling it high when configuration is finished.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The /RESET GPIO is not manipulated from atomic context so support GPIOs
that can't be written from atomic context by using _cansleep().
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intn and connect GPIO properties are swapped in the code which will
cause failures at runtime if these are connected, fix the code.
There are currently no in-tree users of this device to check or update.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch simplifies the interface presented by usb_get_status().
Instead of forcing callers to check for the proper data length and
convert the status value to host byte order, the function will now
do these things itself.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An Embedded Host High-Speed Electrical Test (EHSET) test fixture is
used to initiate test modes on a host controller in order to perform
the high speed electrical testing procedure for USB-IF compliance.
When this test fixture is connected to a host, it can enumerate as
one of several selectable VID/PID pairs, each corresponding to one
of the following test modes:
* TEST_SE0_NAK
* TEST_J
* TEST_K
* TEST_PACKET
* HS_HOST_PORT_SUSPEND_RESUME
* SINGLE_STEP_GET_DEV_DESC
* SINGLE_STEP_SET_FEATURE
The USB EHSET procedure can be found here:
http://www.usb.org/developers/onthego/EHSET_v1.01.pdf
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
[jackp@codeaurora.org: imported from commit 073c9409 on codeaurora.org;
minor cleanup and updated author email]
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that no usb misc driver is looking for CONFIG_USB_DEBUG, or DEBUG,
don't enable it in the Makefile, as that's pointless.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we don't use the dbg() macro, remove it, and the module
parameter. Also fix up the "dump_data" function to properly use the
dynamic debug core and the correct printk options, and don't call it
twice per function, as the data doesn't change from the beginning and
the end of the call.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use a custom debug macro for just one driver, instead rely on the
in-kernel dynamic debugging logic, which can handle this much better.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the unneeded tracing macros in this driver. The kernel has a
built-in trace function that can be used if this is really still needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the pr_* calls instead, which are much more descriptive.
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we don't use the dbg() macro, remove it, and the module
parameter. Also fix up the "dump_data" function to properly use the
dynamic debug core and the correct printk options, and don't call it
twice per function, as the data doesn't change from the beginning and
the end of the call.
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use a custom debug macro for just one driver, instead rely on the
in-kernel dynamic debugging logic, which can handle this much better.
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the unneeded tracing macros in this driver. The kernel has a
built-in trace function that can be used if this is really still needed.
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to get rid of CONFIG_USB_DEBUG, so remove the reliance of the
ldusb driver on it. Don't use the custom macro, or a special module
parameter, instead, rely on the in-kernel dynamic debugging
infrastructure, which is much easier to use, and consistant across the
whole kernel.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull "exotic" arch fixes from Geert Uytterhoeven:
"This is a collection of several exotic architecture fixes, and a few
other fixes for issues that were detected while doing the former"
* 'exotic-arch-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: (35 commits)
lib: Move fonts from drivers/video/console/ to lib/fonts/
console/font: Refactor font support code selection logic
Revert "staging/solo6x10: depend on CONFIG_FONTS"
input: cros_ec_keyb_clear_keyboard() depends on CONFIG_PM_SLEEP
score: Wire up asm-generic/xor.h
score: Remove unneeded <asm/dma-mapping.h>
openrisc: Wire up asm-generic/xor.h
h8300/boot: Use POSIX "$((..))" instead of bashism "$[...]"
h8300: Mark H83002 and H83048 CPU support broken
h8300: Switch h8300 to drivers/Kconfig
h8300: Limit timer channel ranges in Kconfig
h8300: Wire up asm-generic/xor.h
h8300: Fill the system call table using a CALL() macro
h8300: Fix <asm/tlb.h>
h8300: Hardcode symbol prefixes in asm sources
h8300: add missing definition for read_barries_depends()
frv: head.S - Remove commented-out initialization code
cris: Wire up asm-generic/vga.h
parport: disable PC-style parallel port support on cris
console: Disable VGA text console support on cris
...
Here is the big TTY / Serial driver merge for 3.11-rc1.
It's not all that big, nothing major changed in the tty api, which is a
nice change, just a number of serial driver fixes and updates and new
drivers, along with some n_tty fixes to help resolve some reported
issues.
All of these have been in the linux-next releases for a while, with the
exception of the last revert patch, which was reported this past weekend
by two different people as being needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHRtNIACgkQMUfUDdst+ymYgwCeKdyv9wRJ5cIWZt7Jz8ou3P/C
76YAoIvMv+fwoFBpyud/sC8eAKGTQ6KB
=Sjk6
-----END PGP SIGNATURE-----
Merge tag 'tty-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big TTY / Serial driver merge for 3.11-rc1.
It's not all that big, nothing major changed in the tty api, which is
a nice change, just a number of serial driver fixes and updates and
new drivers, along with some n_tty fixes to help resolve some reported
issues.
All of these have been in the linux-next releases for a while, with
the exception of the last revert patch, which was reported this past
weekend by two different people as being needed."
* tag 'tty-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (51 commits)
Revert "serial: 8250_pci: add support for another kind of NetMos Technology PCI 9835 Multi-I/O Controller"
pch_uart: Add uart_clk selection for the MinnowBoard
tty: atmel_serial: prepare clk before calling enable
tty: Reset itty for other pty
n_tty: Buffer work should not reschedule itself
n_tty: Fix unsafe update of available buffer space
n_tty: Untangle read completion variables
n_tty: Encapsulate minimum_to_wake within N_TTY
serial: omap: Fix device tree based PM runtime
serial: imx: Fix serial clock unbalance
serial/mpc52xx_uart: fix kernel panic when system reboot
serial: mfd: Add sysrq support
serial: imx: enable the clocks for console
tty: serial: add Freescale lpuart driver support
serial: imx: Improve Kconfig text
serial: imx: Allow module build
serial: imx: Fix warning when !CONFIG_SERIAL_IMX_CONSOLE
tty/serial/sirf: fix error propagation in sirfsoc_uart_probe()
serial: omap: fix potential NULL pointer dereference in serial_omap_runtime_suspend()
tty: serial: Enable uartlite for ARM zynq
...
The current Makefile rules to build font support are messy and buggy.
Replace them by Kconfig rules:
- Introduce CONFIG_FONT_SUPPORT, which controls the building of all font
code,
- Select CONFIG_FONT_SUPPORT for all drivers that use fonts,
- Select CONFIG_FONT_8x16 for all drivers that default to the VGA8x16
font,
- Drop the bogus console dependency for CONFIG_VIDEO_VIVI,
- Always process drivers/video/console/Makefile, as some drivers need
fonts even if CONFIG_VT is not set.
This fixes (if CONFIG_SOLO6X10=y and there are no built-in console
drivers):
drivers/built-in.o: In function `solo_osd_print':
drivers/staging/media/solo6x10/solo6x10-enc.c:144: undefined reference to `.find_font'
This fixes (if CONFIG_VT=n):
drivers/built-in.o: In function `vivi_init':
vivi.c:(.init.text+0x1a3da): undefined reference to `find_font'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> [original part]
Acked-by: Randy Dunlap <rdunlap@infradead.org> [drivers/video/Makefile]
The usb3503 driver sleeps a flat 100ms when resetting the chip, with a
comment about waiting for the reference clock. This seems to be a
board-specific detail that should not hold up boot across all platforms.
This patch reduces the sleep to the 4ms initialization delay that the
chip itself actually requires (as per its data sheet). If certain boards
require more time to set up the reference clock, they should change this
through local patches or add a proper, configurable synchronization
mechanism.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove an erroneous tab that should be a space.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to add a property 'disabled-ports' representing the unused port
of USB3503. USB3503 can support up to 3 USB host port and each ports can be
controlled to be enabled or disabled. Do not describe this property if all
ports must be enabled.
You can represent the ports to disable in the device tree.
usb3503@08{
...
disabled-ports = <2 3>;
...
};
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to disable the USB ports unconnected to USB3503. In order to
disable the port, 'port_off_mask' must be set.
* Disable PORT1 only
.port_off_mask = USB3503_OFF_PORT1;
* Disable PORT1 and PORT3 only
.port_off_mask = USB3503_OFF_PORT1 | USB3503_OFF_PORT3;
* Enables all ports
.port_off_mask = 0;
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Impact:
1:convert all remain take_over_console to do_take_over_console
2:update take_over_console to do_take_over_console in comment
Commit dc9641895a ("vt: delete unneeded functions
register_con_driver|take_over_console") delete take_over_console,
but forget to convert remain take_over_console's users to new API
do_take_over_console, this patch fix it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed the assignment error in an if statement in adutux.c
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eliminated the error of whitespace needed after a closing brace
in adutux.c
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added space after comma in dbg() and usb_fill_int_urb() function
calls in adutux.c to meet kernel coding standards.
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replaced asm/uaccess.h with linux/uaccess.h in adutux.c
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
This patch removes the depends on USB from all config symbols in
drivers/usb/host/Kconfig and replace that with an if USB / endif block
as suggested by Alan Stern. Some source ... Kconfig lines have been
shuffled around to permit a better regroupment of the Kconfig files
depending on "config USB" item. No functionnal change is introduced.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the Apple 24" LED Cinema display to the supported devices.
Signed-off-by: Ben Jencks <ben@bjencks.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A failed kzalloc() is reported with a dev_err that dereferences the null
sisusb, this will cause a NULL pointer deference error.
Instead, pass dev->dev to the dev_err() rather than &sisusb->sisusb_dev->dev
Smatch analysis:
drivers/usb/misc/sisusbvga/sisusb.c:3087 sisusb_probe() error: potential null
dereference 'sisusb'. (kzalloc returns null)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_i2c_driver() macro to make the code smaller
and a bit simpler.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbtest driver includes some rather simple-minded logic for
selecting an altsetting to test. It doesn't work well for the g_zero
gadget, because it selects altsetting 0 (which doesn't have
isochronous endpoints) rather than altsetting 1 (which does have them,
if the gadget's hardware supports them). This prevents usbtest's
isochronous tests (15, 16, 22, and 23) from working with g_zero.
Since g_zero is one of the most common gadget drivers used for USB
testing, usbtest should do a better job of supporting it. But since
some programs may rely on the current scheme for selecting
altsettings, I didn't want to change it.
Instead, this patch (as1655) adds a module parameter to usbtest, which
can be used to override the default altsetting. Since usbtest is
never used by normal users (most distributions probably don't even
build it), the new module parameter won't inconvenience anybody. In
any case, it is entirely optional -- leaving it unset preserves the
existing behavior.
The patch also fixes a related bug in usbtest: After selecting an
altsetting, the driver neglects to store its selection.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the compiler warning of uninitialized variable.
drivers/usb/misc/usb3503.c: In function ‘usb3503_probe’:
drivers/usb/misc/usb3503.c:215:13: warning: ‘mode’ may be used uninitialized
in this function [-Wuninitialized]
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added device tree support for usb3503 driver and add new document with device tree binding information.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the warning,
6a099c6365 [4/10] USB: misc: Add USB3503 High-Speed Hub Controller
drivers/usb/misc/usb3503.c:238 usb3503_probe() error: we previously assumed 'pdata' could be null (see line 196)
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds new driver of SMSC USB3503 USB 2.0 hub controller with HSIC
upstream connectivity and three USB 2.0 downstream ports. The specification
can be found from 'http://www.smsc.com/index.php?tid=295&pid=325'.
The current version have been tested very basic features switching the modes,
HUB-MODE and STANDBY-MODE.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1639) fixes a minor bug in the usbtest driver. Due to
concurrent changes, a test originally written as number 17 got changed
to number 24, but the corresponding change was not made in the log
message. This updates the log message.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an error during modpost, when ezusb is built into the kernel
while USB is built as module.
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
Cc: stable <stable@vger.kernel.org>
--
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If param->length is zero, then this could lead to a divide by zero bug
later in the function when we do: size %= max;
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
since commit b4036cc (usb: gadget: add
isochronous support to gadget zero), g_zero
has learned about isochronous transfers, which
allows us to use usbtest.ko to exercise
isochronous pipes.
All we need to do to enable that functionality
on usbtest.ko, is set the "iso" to 1 on
struct usbtest_info
Signed-off-by: Boyan Nedeltchev <boyan@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pulls in all of the USB changes in 3.7-rc3 into usb-next and
resolves the merge issue with:
drivers/usb/misc/ezusb.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the ezusb code was split out, support was added for the fx2 chip
type, but no one is using these functions, so comment it out. If
someone needs it, it can be added back in the future.
Also properly include <linux/usb/ezusb.h> into the ezusb.c file, to
ensure we catch any function prototype mis-matches
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: René Bürgel <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch
- moves drivers/usb/serial/ezusb.c to drivers/usb/misc/
- renamed CONFIG_USB_EZUSB to CONFIG_USB_EZUSB_FX2 to avoid build errors
- adapts Makefiles and Kconfigs switching from bool to tristate for CONFIG_USB_EZUSB_FX2
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"udev" can't be NULL here. The debugging printk() makes static checkers
complain when we dereference it later in the function inside the call to
usb_rcvctrlpipe().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Zack Parsons <k3bacon@gmail.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Cesar Miquel <miquel@df.uba.ar>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bMaxPacketSize0 field for super speed is a power of 2, not a count.
The size itself is always 512.
Max packet size for a super speed bulk endpoint is 1024, so
allocate the urb size in halt_simple() accordingly.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the conflict in:
drivers/usb/host/ehci-fsl.c
And picks up loads of xhci bugfixes to make it easier for others to test
with.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Zack Parsons <k3bacon@gmail.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Cesar Miquel <miquel@df.uba.ar>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Juergen Stuber <starblue@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Michael Hund <mhund@ld-didactic.de>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current probing code is setting URB_NO_TRANSFER_DMA_MAP flag into a wrong urb
structure, and this causes BUG_ON with some USB host implementations.
This patch fixes the issue.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes allocation of coherent buffer for the control-request setup-packet
buffer from the yurex driver. Using coherent buffers for setup-packet is
obsolete and does not work with some USB host implementations.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Free the two previously allocated buffers before exiting the function in an
error case.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A large `nents' from userspace could overflow the allocation size,
leading to memory corruption.
| alloc_sglist()
| usbtest_ioctl()
Use kmalloc_array() to avoid the overflow.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid overflowing context.count = param->sglen * param->iterations,
where both `sglen' and `iterations' are from userspace.
| test_ctrl_queue()
| usbtest_ioctl()
Keep -EOPNOTSUPP for error code.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This changes the max length for the usb seven segment delcom device to 8
from 6. Delcom has both 6 and 8 variants and having 8 works fine with
devices which are only 6.
Signed-off-by: Harrison Metzger <harrisonmetz@gmail.com>
Signed-off-by: Stuart Pook <stuart@acm.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Huang Rui
Greg Kroah-Hartman
Matthew Dawson
Johan Hovold
Manu Gautam
Mark Brown
Alan Stern
Jingoo Han
Jóhann B. Guðmundsson
Linus Torvalds
Geert Uytterhoeven
Julius Werner
Dongjin Kim
Wang YanQing
Lisa Nguyen
Al Viro
Masanari Iida
Florian Fainelli
Ben Jencks
Colin Ian King
Wei Yongjun
Fengguang Wu
Rene Buergel
Dan Carpenter
Boyan Nedeltchev
Dave Jones
Peter Senna Tschudin
Paul Zimmerman
Tomoki Sekiyama
Julia Lawall
Xi Wang
Harrison Metzger