devlink suffers from a few kdoc warnings:
net/core/devlink.c:5292: warning: Function parameter or member 'dev' not described in 'devlink_register'
net/core/devlink.c:5351: warning: Function parameter or member 'port_index' not described in 'devlink_port_register'
net/core/devlink.c:5753: warning: Function parameter or member 'parent_resource_id' not described in 'devlink_resource_register'
net/core/devlink.c:5753: warning: Function parameter or member 'size_params' not described in 'devlink_resource_register'
net/core/devlink.c:5753: warning: Excess function parameter 'top_hierarchy' description in 'devlink_resource_register'
net/core/devlink.c:5753: warning: Excess function parameter 'reload_required' description in 'devlink_resource_register'
net/core/devlink.c:5753: warning: Excess function parameter 'parent_reosurce_id' description in 'devlink_resource_register'
net/core/devlink.c:6451: warning: Function parameter or member 'region' not described in 'devlink_region_snapshot_create'
net/core/devlink.c:6451: warning: Excess function parameter 'devlink_region' description in 'devlink_region_snapshot_create'
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh says:
====================
net: aquantia: minor bug fixes after static analysis
This patchset fixes minor errors and warnings found by smatch and kasan.
Extra patch is to replace AQ_HW_WAIT_FOR with readx_poll_timeout
to improve readability.
V2:
use readx_poll
resubmitted to net-next since the changeset became quite big.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace some direct registers reads with better
online functions.
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David noticed the original define was hiding 'err' variable
reference. Thats confusing and counterintuitive.
Andrew noted the whole macro could be replaced with standard readx_poll
kernel macro. This makes code more readable.
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a real stack undercorruption found by kasan build.
The issue did no harm normally because it only overflowed
2 bytes after `bitary` array which on most architectures
were mapped into `err` local.
Fixes: bab6de8fd1 ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.")
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The overflow is detected by smatch:
drivers/net/ethernet/aquantia/atlantic/aq_pci_func.c: 175
aq_pci_func_free_irqs() error: buffer overflow 'self->aq_vec' 8 <= 31
In reality msix_entry_mask always restricts number of iterations.
Adding extra condition to make logic clear and smatch happy.
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/aquantia/atlantic/aq_nic.c: 991:1:
warning: no newline at end of file
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not careful array dereference caused analysis tools
to think there could be memory overflow.
There was actually no corruption because the array is
two dimensional.
drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c: 140
aq_ethtool_get_strings() error:
memcpy() '*aq_ethtool_stat_names' too small (32 vs 704)
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ip rules, we need to use 'ipproto ipv6-icmp' to match ICMPv6 headers.
But for ip -6 route, currently we only support tcp, udp and icmp.
Add ICMPv6 support so we can match ipv6-icmp rules for route lookup.
v2: As David Ahern and Sabrina Dubroca suggested, Add an argument to
rtm_getroute_parse_ip_proto() to handle ICMP/ICMPv6 with different family.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: eacb9384a3 ("ipv6: support sport, dport and ip_proto in RTM_GETROUTE")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compiling xdpsock_user.c with 4.8.5, I hit the following
compilation warning:
HOSTCC samples/bpf/xdpsock_user.o
/data/users/yhs/work/net-next/samples/bpf/xdpsock_user.c: In function ‘main’:
/data/users/yhs/work/net-next/samples/bpf/xdpsock_user.c:449:6: warning: ‘idx_cq’ may be used unini
tialized in this function [-Wmaybe-uninitialized]
u32 idx_cq, idx_fq;
^
/data/users/yhs/work/net-next/samples/bpf/xdpsock_user.c:606:7: warning: ‘idx_rx’ may be used unini
tialized in this function [-Wmaybe-uninitialized]
u32 idx_rx, idx_tx = 0;
^
/data/users/yhs/work/net-next/samples/bpf/xdpsock_user.c:506:6: warning: ‘idx_rx’ may be used unini
tialized in this function [-Wmaybe-uninitialized]
u32 idx_rx, idx_fq = 0;
As an example, the code pattern looks like:
u32 idx_cq;
...
ret = xsk_ring_prod__reserve(&xsk->umem->fq, rcvd, &idx_fq);
if (ret) {
...
}
... idx_fq ...
The compiler warns since it does not know whether &idx_fq is assigned
or not inside the library function xsk_ring_prod__reserve().
Let us assign an initial value 0 to such auto variables to silence
compiler warning.
Fixes: 248c7f9c0e ("samples/bpf: convert xdpsock to use libbpf for AF_XDP access")
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This is to avoid permission denied error. A lot of systems
may have a much lower number, e.g., 64KB, for RLIMIT_MEMLOCK,
which may not be sufficient for the test to run successfully.
Fixes: e0b27b3f97 ("bpf: Add test_sock_fields for skb->sk and bpf_tcp_sock")
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Andrii Nakryiko says:
====================
A bunch of BPF-related docs typo, wording and formatting fixes.
v1->v2:
- split off non-documentation changes into separate patchset
====================
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reflow paragraphs to more fully and evenly fill 78 character lines.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Fix various typos, some of the formatting and wording for
Documentation/btf.rst.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
We need to iterate through all possible cpus.
Fixes: 492ecee892 ("bpf: enable program stats")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The MIPS eBPF JIT calls flush_icache_range() in order to ensure the
icache observes the code that we just wrote. Unfortunately it gets the
end address calculation wrong due to some bad pointer arithmetic.
The struct jit_ctx target field is of type pointer to u32, and as such
adding one to it will increment the address being pointed to by 4 bytes.
Therefore in order to find the address of the end of the code we simply
need to add the number of 4 byte instructions emitted, but we mistakenly
add the number of instructions multiplied by 4. This results in the call
to flush_icache_range() operating on a memory region 4x larger than
intended, which is always wasteful and can cause crashes if we overrun
into an unmapped page.
Fix this by correcting the pointer arithmetic to remove the bogus
multiplication, and use braces to remove the need for a set of brackets
whilst also making it obvious that the target field is a pointer.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: b6bd53f9c4 ("MIPS: Add missing file for eBPF JIT.")
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: netdev@vger.kernel.org
Cc: bpf@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add the upcoming ConnectX-6 Dx.
In addition, add "ConnectX Family mlx5Gen Virtual Function" device ID.
Every new HCA VF will be identified with this device ID. Different VF
models will be distinguished by their revision id.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Update the predicate that determines if to duplicate rules installed on
vport reps to account also for the multipath case.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current check only validates if both netdevs use the same ops
which means both are vf reps or both uplink reps.
Unlike the case where the two uplinks are bonded (VF LAG), under
multipath scheme the switchdev parent id is not unified between the
uplink reps (and all the associated vf reps). However, we still want
to duplicate in the driver encap flows, adjust the merged eswitch
check for that matter.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As part of creating the tunnel headers while offloading TC encap rules,
we resolve the route and neighbour in order to get the source /
destination mac.
Since the way we offload multipath route is by having two HW rules,
one per uplink port, doing naive route lookup might get us a "wrong"
routing path which goes through the peer uplink and this will get us
eventually to create a wrong L2 header for the tunnel.
To avoid that, we use a device hint to get the correct route.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Under multipath when encap rules are duplicated to HW in the driver,
it's possible for one flow to be currently un-offloaded (e.g. lack of
next-hop route or neigh entry) while the other flow is offloaded. As
such, we move to query the counters of both flows at all times.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Under multipath it's possible for us to offload the flow only through
the e-switch for which proper route through the uplink exists.
When the port is up and the next-hop route is set again we want to
offload through it as well.
We generate SW event from the FIB event handler when multipath port
affinity changes. The tc offloads code gets this event, goes over the
flows which were marked as of having missing route and attempts to
offload them.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Under multipath offload scheme, as part of handling fib events, emit
mlx5 port affinity event on the enabled ports which will be handled by
the tc offloads code.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In a similar manner to uplink/VF LAG, under multipath we add encap peer
rule on the second port as well.
However, unlike the LAG case, we do want to allow failure for adding
one of the rules. This happens due to using a routing hint while doing
the route lookup when one path (next hop device) is down.
Introduce a new flag to indicate that route lookup failed for encap
flow. Note that a flow may still not be offloaded to hw due to missing
neighbour, in that case, the neigh update event will take care of it.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the peer flow inherits the flags from the original flow
after we've set it. At this time the flags are set according to
the flow state, e.g marked as going to slow path and such.
Even if not getting us to real bugs now, this opens the door to
get us to troubles later. Future proof the code and avoid the
inheritance, use the peer flags as were set on input when we
started adding the original flow.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
To support multipath offload we are going to track SW multipath route
and related nexthops. To do that we register to FIB notifier and handle
the route and next-hops events and reflect that as port affinity to HW.
When there is a new multipath route entry that all next-hops are the
ports of an HCA we will activate LAG in HW.
Egress wise, we use HW LAG as the means to emulate multipath on current
HW which doesn't support port selection based on xmit hash. In the
presence of multiple VFs which use multiple SQs (send queues) this
yields fairly good distribution.
HA wise, HW LAG buys us the ability for a given RQ (receive queue) to
receive traffic from both ports and for SQs to migrate xmitting over
the active port if their base port fails.
When the route entry is being updated to single path we will update
the HW port affinity to use that port only.
If a next-hop becomes dead we update the HW port affinity to the living
port.
When all next-hops are alive again we reset the affinity to default.
Due to FW/HW limitations, when a route is deleted we are not disabling
the HW LAG since doing so will not allow us to enable it again while
VFs are bounded. Typically this is just a temporary state when a
routing daemon removes dead routes and later adds them back as needed.
This patch only handles events for AF_INET.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to offload ecmp-on-host scheme where next-hop routes are used,
we will make use of HW LAG. Add accessor function to let upper layers
in the driver to realize if the lag acts in multi-path mode.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Instead of using the system workqueue, allocate our own workqueue.
This workqueue will be used to handle more work in the next patch.
This patch doesn't change functionality.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The change is a refactoring step towards a multipath use case.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This fix checkpatch check
CHECK: Avoid using bool structure members because of possible alignment
issues
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
EAGAIN is treated as a specific case when we consider the attachment
successful but wait for neigh event before offloading the flow.
This can result in unwanted behavior when sub calls on the offloading
path will return EAGAIN and we pass this error up.
Instead of attaching to a specific error code return a boolean value
from the attach encap operation saying if the encap is valid or not.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the tunnel info argument which we can get from the other args.
Also reorder the args to have input args first and output args later.
This patch doesn't change functionality.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Function mlx5e_tx_reporter_recover_from_ctx is only used within mlx5e tx
reporter, move it to be statically declared in en/reporter_tx.c.
Fixes: de8650a820 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Jakub Kicinski says:
====================
nfp: control processor DMA support and RJ45
This series starts with adding support for reporting twisted pair
media type in ethtool.
Remaining patches add support for using DMA with the control/service
processor. Currently we always copy the command data into card's
memory. DMA support allows us to have the NSP read the data from
host memory by itself. Unfortunately, the FW loading and flashing
cannot directly map the buffers for DMA because (a) the firmware
ABI returns const buffers, and (b) the buffers may be vmalloc()ed
in many mysterious/unmappable way. So just bite the bullet -
allocate new host buffer for the command and copy.
As Dirk explains, the NSP now supports updating all FWs at once
which means the max flashing time grew significantly. He bumps
the max wait to avoid timeouts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The management firmware now supports being passed a bundle with
multiple components to be stored in flash at once. This makes it
easier to update all components to a known state with a single
user command, however, this also has the potential to increase
the time required to perform the update significantly.
The management firmware only updates the components out of a bundle
which are outdated, however, we need to make sure we can handle
the absolute worst case where a CPLD update can take a long time
to perform.
We set a very conservative total timeout of 900s which already
adds a contingency.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer versions of NSP can access host memory. Simplest access
type requires all data to be in one contiguous area. Since we
don't have the guarantee on where callers of the NSP ABI will
allocate their buffers we allocate a bounce buffer and copy
the data in and out.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA version of NSP communication is coming, move the code which
copies data into the NFP buffer into a separate function.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NSP expresses the buffer size in MB and 4 kB blocks. For small
buffers the kB part may make a difference, so count it in.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reporting twisted pair port type.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been observed that tx queue stalls while downloading
from certain web sites (example www.speedtest.net)
The cause has been tracked down to a corner case where
dma descriptors where not setup properly. And there for a tx
completion interrupt was not signaled.
This fix corrects the problem by properly marking the end of
a multi descriptor transmission.
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When debugging an issue I found implausible values in state->pause.
Reason in that state->pause isn't initialized and later only single
bits are changed. Also the struct itself isn't initialized in
phylink_resolve(). So better initialize state->pause and other
not yet initialized fields.
v2:
- use right function name in subject
v3:
- initialize additional fields
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently the maximum number of queues was increased up to 8, but
NIC was not fully configured for 8 queues. In setups with more than 4 CPU
cores parts of TX traffic gets lost if the kernel routes it to queues 4th-8th.
This patch sets a tx hw traffic mode with 8 queues.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202651
Fixes: 71a963cfc5 ("net: aquantia: increase max number of hw queues")
Reported-by: Nicholas Johnson <nicholas.johnson@outlook.com.au>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation for UDP GRO tests is racy: the receiver
may flush the RX queue while the sending is still transmitting and
incorrectly report RX errors, with a wrong number of packet received.
Add explicit timeouts to the receiver for both connection activation
(first packet received for UDP) and reception completion, so that
in the above critical scenario the receiver will wait for the
transfer completion.
Fixes: 3327a9c463 ("selftests: add functionals test for UDP GRO")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comphy driver for Armada 3700 by Miquèl Raynal (which is currently
in linux-next) does not actually set comphy mode when phy_set_mode_ext
is called. The mode is set at next call of phy_power_on.
Update the driver to semantics similar to mvpp2: helper
mvneta_comphy_init sets comphy mode and powers it on.
When mode is to be changed in mvneta_mac_config, first power the comphy
off, then call mvneta_comphy_init (which sets the mode to new one).
Only do this when new mode is different from old mode.
This should also work for Armada 38x, since in that comphy driver
methods power_on and power_off are unimplemented.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil says:
====================
enetc: Add mdio support and device tree nodes
This is the missing part to enable PCI probing of the ENETC ethernet
ports on the LS1028A SoC and external traffic on the LS1028A RDB board.
It's one of the first items on the TODO list for the recently merged
ENETC ethernet driver.
v3: Add DT bindings doc for ENETC connections
v4: none
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Define connection bindings (external PHY connections and internal links)
for the ENETC on-chip ethernet controllers.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each ENETC PF has its own MDIO interface, the corresponding
MDIO registers are mapped in the ENETC's Port register block.
The current patch adds a driver for these PF level MDIO buses,
so that each PF can manage directly its own external link.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LS1028A RDB board features an Atheros PHY connected over
SGMII to the ENETC PF0 (or Port0). ENETC Port1 (PF1) has no
external connection on this board, so it can be disabled for now.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LS1028A SoC features a PCI Integrated Endpoint Root Complex
(IERC) defining several integrated PCI devices, including the ENETC
ethernet controller integrated endpoints (IEPs). The IERC implements
ECAM (Enhanced Configuration Access Mechanism) to provide access
to the PCIe config space of the IEPs. This means the the IEPs
(including ENETC) do not support the standard PCIe BARs, instead
the Enhanced Allocation (EA) capability structures in the ECAM space
are used to fix the base addresses in the system, and the PCI
subsystem uses these structures for device enumeration and discovery.
The "ranges" entries contain basic information from these EA capabily
structures required by the kernel for device enumeration.
The current patch also enables the first 2 ENETC PFs (Physiscal
Functions) and the associated VFs (Virtual Functions), 2 VFs for
each PF. Each of these ENETC PFs has an external ethernet port
on the LS1028A SoC.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski
David S. Miller
Nikita Danilov
Igor Russkikh
Hangbin Liu
Yonghong Song
Daniel Borkmann
Andrii Nakryiko
Eric Dumazet
Paul Burton
Eran Ben Elisha
Roi Dayan
Dirk van der Merwe
Bryan Whitehead
Heiner Kallweit
Dmitry Bogdanov
Paolo Abeni
Marek Behún
Claudiu Manoil