These command do have variable length and the length can go up to 251,
so this changes the struct to not use a fixed size and then when
creating the PDU only the actual length of the data send to the
controller.
Fixes: a0fb3726ba ("Bluetooth: Use Set ext adv/scan rsp data if controller supports")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
blacklist -> reject list
whitelist -> accept list
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
master -> central
slave -> peripheral
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Disable duplicates filter when scanning for advertisement monitor for
the following reasons. The scanning includes active scan and passive
scan.
For HW pattern filtering (ex. MSFT), Realtek and Qualcomm controllers
ignore RSSI_Sampling_Period when the duplicates filter is enabled.
For SW pattern filtering, when we're not doing interleaved scanning, it
is necessary to disable duplicates filter, otherwise hosts can only
receive one advertisement and it's impossible to know if a peer is still
in range.
Signed-off-by: Yun-Hao Chung <howardchung@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to
walk all map elements in a more robust and easier to verify
fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF
on s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices
which don't need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability
on next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is
slow in reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take
place correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP
packets before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used
to define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
-independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and
bnxt support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP
which define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay
for packets sampled from switch HW (and corresponding egress
and policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP
forwarding, bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface
to distribute MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x -
11-port Ethernet switch with 8x 1-Gigabit Ethernet
and 3x 10-Gigabit interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
and BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack,
matching on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode
changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vcbA
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
There is a possible race condition vulnerability between issuing a HCI
command and removing the cont. Specifically, functions hci_req_sync()
and hci_dev_do_close() can race each other like below:
thread-A in hci_req_sync() | thread-B in hci_dev_do_close()
| hci_req_sync_lock(hdev);
test_bit(HCI_UP, &hdev->flags); |
... | test_and_clear_bit(HCI_UP, &hdev->flags)
hci_req_sync_lock(hdev); |
|
In this commit we alter the sequence in function hci_req_sync(). Hence,
the thread-A cannot issue th.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Cc: Marcel Holtmann <marcel@holtmann.org>
Fixes: 7c6a329e44 ("[Bluetooth] Fix regression from using default link policy")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
own_address_type has to changed to 0x02 and 0x03 only when
HCI_ENABLE_LL_PRIVACY flag is set.
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is a possibility where HCI_INQUIRY flag is set but we still
send HCI_OP_INQUIRY anyway.
Such a case can be reproduced by connecting to an LE device while
active scanning. When the device is discovered, we initiate a
connection, stop LE Scan, and send Discovery MGMT with status
disabled, but we don't cancel the inquiry.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
1. Add space when needed;
2. Block comments style fix;
3. Move open brace '{' following function definitions to the next line;
4. Remove unnecessary braces '{}' for single statement blocks.
Signed-off-by: Meng Yu <yumeng18@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Not cancelling it has caused a bug where passive background scanning is
disabled out of the blue, preventing BLE keyboards/mice to reconnect.
Here is how it happens:
After hci_req_stop_discovery, there is still le_scan_restart_work
scheduled. Invocation of le_scan_restart_work causes a harmful
le_scan_disable_work to be scheduled. This le_scan_disable_work will
eventually disable passive scanning when the timer fires.
Sample btmon trace:
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7
Type: Passive (0x00)
Interval: 367.500 msec (0x024c)
Window: 37.500 msec (0x003c)
Own address type: Public (0x00)
Filter policy: Accept all advertisement (0x00)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Scan Parameters (0x08|0x000b) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2
Scanning: Enabled (0x01)
Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Scan Enable (0x08|0x000c) ncmd 2
Status: Success (0x00)
...
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2
Scanning: Disabled (0x00)
Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Scan Enable (0x08|0x000c) ncmd 2
Status: Success (0x00)
// Background scanning is not working here onwards.
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
An issue was found, where if a bluetooth client requests a broadcast
advertisement with scan response data, it will not be properly
registered with the controller. This is because at the time that the
hci_cp_le_set_scan_param structure is created, the scan response will
not yet have been received since it comes in a second MGMT call. With
empty scan response, the request defaults to a non-scannable PDU type.
On some controllers, the subsequent scan response request will fail due
to incorrect PDU type, and others will succeed and not use the scan
response.
This fix allows the advertising parameters MGMT call to include a flag
to let the kernel know whether a scan response will be coming, so that
the correct PDU type is used in the first place. A bluetoothd change is
also incoming to take advantage of it.
To test this, I created a broadcast advertisement with scan response
data and registered it on the hatch chromebook. Without this change, the
request fails, and with it will succeed.
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During suspend, there are a few scan enable and set event filter
commands that don't need to be sent unless there are actual BR/EDR
devices capable of waking the system. Check the HCI_PSCAN bit before
writing scan enable and use a new dev flag, HCI_EVENT_FILTER_CONFIGURED
to control whether to clear the event filter.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds logic to disable and reenable advertisement filters during
suspend and resume. After this patch, we would only receive packets from
devices in allow list during suspend.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When MSFT extension is supported, we don't have to interleave the scan
as we could just do allowlist scan.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a missing SUSPEND_SCAN_ENABLE in passive scan, remove the separate
function for configuring le scan during suspend and update the request
complete function to clear both enable and disable tasks.
Fixes: dce0a4be80 ("Bluetooth: Set missing suspend task bits")
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When suspending, mark SUSPEND_SCAN_ENABLE and SUSPEND_SCAN_DISABLE tasks
correctly when either classic or le scanning is modified.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch takes the min/max intervals and tx power optionally provided
in mgmt interface, stores them in the advertisement struct, and uses
them when configuring the hci requests. While tx power is not used if
extended advertising is unavailable, software rotation will use the min
and max advertising intervals specified by the client.
This change is validated manually by ensuring the min/max intervals are
propagated to the controller on both hatch (extended advertising) and
kukui (no extended advertising) chromebooks, and that tx power is
propagated correctly on hatch. These tests are performed with multiple
advertisements simultaneously.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch add a configurable parameter to switch off the interleave
scan feature.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds code to handle the active scan during interleave
scan. The interleave scan will be canceled when users start active scan,
and it will be restarted after active scan stopped.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds code to handle the system suspension during interleave
scan. The interleave scan will be canceled when the system is going to
sleep, and will be restarted after waking up.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch implements the interleaving between allowlist scan and
no-filter scan. It'll be used to save power when at least one monitor is
registered and at least one pending connection or one device to be
scanned for.
The durations of the allowlist scan and the no-filter scan are
controlled by MGMT command: Set Default System Configuration. The
default values are set randomly for now.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This renames get_adv_instance_scan_rsp to adv_instance_is_scannable and
make it return a bool since it was not actually properly return the size
of the scan response as one could expect.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Current code is actually failing on the following tests of mgmt-tester
because get_adv_instance_scan_rsp_len did not account for flags that
cause scan response data to be included resulting in non-scannable
instance when in fact it should be scannable.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This replaces the BT_DBG function to bt_dev_dbg as it is cleaner to show
the controller index in the debug message.
Signed-off-by: Howard Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When adding device to white list the device is added to resolving list
also. It has to be added only when HCI_ENABLE_LL_PRIVACY flag is set.
HCI_ENABLE_LL_PRIVACY flag has to be tested before adding/deleting devices
to resolving list. use_ll_privacy macro is used only to check if controller
supports LL_Privacy.
https://bugzilla.kernel.org/show_bug.cgi?id=209745
Fixes: 0eee35bdfa ("Bluetooth: Update resolving list when updating whitelist")
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When an LE connection request is made, advertising is disabled and never
resumed. When a client has an active advertisement, this is disruptive.
This change adds resume logic for client-configured (non-directed)
advertisements after the connection attempt.
The patch was tested by registering an advertisement, initiating an LE
connection from a remote peer, and verifying that the advertisement is
re-activated after the connection is established. This is performed on
Hatch and Kukui Chromebooks.
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During system powercycle when trying to get the random address
hci_get_random_address set own_addr_type as 0x01. In which if we enable
ll_privacy it is supposed to be 0x03.
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Set scan parameters when there is at least one Advertisement monitor.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently, the controller will continue advertising when the system
enters suspend. This patch makes sure that all advertising instances are
paused when entering suspend, and resumed when suspend exits.
The Advertising and Suspend/Resume test suites were both run on this
change on 4.19 kernel with both hardware offloaded multi-advertising and
software rotated multi-advertising. In addition, a new test was added
that performs the following steps:
* Register 3 advertisements via bluez RegisterAdvertisement
* Verify reception of all advertisements by remote peer
* Enter suspend on DUT
* Verify failure to receive all advertisements by remote peer
* Exit suspend on DUT
* Verify reception of all advertisements by remote peer
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only set extended scan response only when it exists. Otherwise, clear
the scan response data.
Per the core spec v5.2, Vol 4, Part E, 7.8.55
If the advertising set is non-scannable and the Host uses this command
other than to discard existing data, the Controller shall return the
error code Invalid HCI Command Parameters (0x12).
On WCN3991, the controller correctly responds with Invalid Parameters
when this is sent. That error causes __hci_req_hci_power_on to fail
with -EINVAL and LE devices can't connect because background scanning
isn't configured.
Here is an hci trace of where this issue occurs during power on:
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
Handle: 0x00
Properties: 0x0010
Use legacy advertising PDUs: ADV_NONCONN_IND
Min advertising interval: 181.250 msec (0x0122)
Max advertising interval: 181.250 msec (0x0122)
Channel map: 37, 38, 39 (0x07)
Own address type: Random (0x01)
Peer address type: Public (0x00)
Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
Filter policy: Allow Scan Request from Any, Allow Connect...
TX power: 127 dbm (0x7f)
Primary PHY: LE 1M (0x01)
Secondary max skip: 0x00
Secondary PHY: LE 1M (0x01)
SID: 0x00
Scan request notifications: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 5
LE Set Extended Advertising Parameters (0x08|0x0036) ncmd 1
Status: Success (0x00)
TX power (selected): 9 dbm (0x09)
< HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7
Advertising handle: 0x00
Advertising random address: 08:FD:55:ED:22:28 (OUI 08-FD-55)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertising Set Random Address (0x08|0x0035) ncmd
Status: Success (0x00)
< HCI Command: LE Set Extended Scan Response Data (0x08|0x0038) plen 35
Handle: 0x00
Operation: Complete scan response data (0x03)
Fragment preference: Minimize fragmentation (0x01)
Data length: 0x0d
Name (short): Chromebook
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Scan Response Data (0x08|0x0038) ncmd 1
Status: Invalid HCI Command Parameters (0x12)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When an LE connection is requested and an RPA update is needed via
hci_connect_le_scan, the default scanning parameters are used rather
than the connect parameters. This leads to significant delays in the
connection establishment process when using lower duty cycle scanning
parameters.
The patch simply looks at the pended connection list when trying to
determine which scanning parameters should be used.
Before:
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
#378 [hci0] 1659.247156
Own address type: Public (0x00)
Filter policy: Ignore not in white list (0x01)
PHYs: 0x01
Entry 0: LE 1M
Type: Passive (0x00)
Interval: 367.500 msec (0x024c)
Window: 37.500 msec (0x003c)
After:
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
#39 [hci0] 7.422109
Own address type: Public (0x00)
Filter policy: Ignore not in white list (0x01)
PHYs: 0x01
Entry 0: LE 1M
Type: Passive (0x00)
Interval: 60.000 msec (0x0060)
Window: 60.000 msec (0x0060)
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Yu Liu <yudiliu@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support to enable the use of RPA Address resolution
using expermental feature mgmt command.
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In this patch if le_create_conn process is started restrict to
disable address resolution and same is disabled during
le_enh_connection_complete
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When address resolution is enabled and set_privacy is enabled let's
use own address type as 0x03
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the whitelist is updated, then also update the entries of the
resolving list for devices where IRKs are available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the LL Privacy support is available, then as part of enabling or
disabling passive background scanning, it is required to set up the
controller based address resolution as well.
Since only passive background scanning is utilizing the whitelist, the
address resolution is now bound to the whitelist and passive background
scanning. All other resolution can be easily done by the host stack.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add functionality to disable and remove advertising instances,
and use that functionality in MGMT add/remove advertising calls.
Currently, advertising is globally-disabled, i.e. all instances are
disabled together, even if hardware offloading is available. This
patch adds functionality to disable and remove individual adv
instances, solving two issues:
1. On new advertisement registration, a global disable was done, and
then only the new instance was enabled. This meant only the newest
instance was actually enabled.
2. On advertisement removal, the structure was removed, but the instance
was never disabled or removed, which is incorrect with hardware offload
support.
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Reviewed-by: Shyh-In Hwang <josephsih@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Even with one advertisement monitor in place, the scan policy should use
the whitelist while the system is going to suspend to prevent waking by
random advertisement.
The following test was performed.
- With a paired device, register one advertisement monitor, suspend
the system and verify that the host was not awaken by random
advertisements.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes active scans to use the configured default parameters.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When restarting LE scanning, check if it's currently paused before
enabling passive scanning.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the extended advertisement feature is enabled, a hardcoded min and
max interval of 0x8000 is used. This patch fixes this issue by using
the configured min/max value.
This was validated by setting min/max in main.conf and making sure the
right setting is applied:
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen
25 #93 [hci0] 10.953011
…
Min advertising interval: 181.250 msec (0x0122)
Max advertising interval: 181.250 msec (0x0122)
…
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This calls hci_update_background_scan() when there is any update on the
advertisement monitors. If there is at least one advertisement monitor,
the filtering policy of scan parameters should be 0x00. This also reports
device found mgmt events if there is at least one monitor.
The following cases were tested with btmgmt advmon-* commands.
(1) add a ADV monitor and observe that the passive scanning is
triggered.
(2) remove the last ADV monitor and observe that the passive scanning is
terminated.
(3) with a LE peripheral paired, repeat (1) and observe the passive
scanning continues.
(4) with a LE peripheral paired, repeat (2) and observe the passive
scanning continues.
(5) with a ADV monitor, suspend/resume the host and observe the passive
scanning continues.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Replace the wakeable boolean with flags in hci_conn_params and all users
of this boolean. This will be used by the get/set device flags mgmt op.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the classic device list now supports flags, convert the wakeable
list into a flag on the existing device list.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch centralized the initialization of default parameters. This
is required to allow clients to more easily customize the default
system parameters.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Check current scan state by checking HCI_LE_SCAN flag and send scan
disable command only if scan is already enabled.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Renamed BT_SUSPEND_COMPLETE to BT_SUSPEND_CONFIGURE_WAKE since it sets
up the event filter and whitelist for wake-up.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When a device is suspended, it doesn't need to be as responsive to
connection events. Increase the interval to 640ms (creating a duty cycle
of roughly 1.75%) so that passive scanning uses much less power (vs
previous duty cycle of 18.75%). The new window + interval combination
has been tested to work with HID devices (which are currently the only
devices capable of wake up).
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The types for window and interval should be uint16, not uint8.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz
Archie Pusaka
Yun-Hao Chung
Linus Torvalds
Lin Ma
Sathish Narasimman
Meng Yu
Sonny Sasaka
Daniel Winkler
Abhishek Pandit-Subedi
Howard Chung
Sathish Narasimman
Alain Michaud
Marcel Holtmann
Miao-chen Chou
Manish Mandlik