set_fs() is used in HD-audio vmaster code to retrieve the TLV data of
each slave kctl. Since the slave is supposed to be a standard amp
kctl, we can call directly the supposed tlv callback instead of the
indirect call, so that we can remove the set_fs() hack.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now all the users of this workaround code is gone, and we can finally
remove the legacy codes from the core HD-audio module.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The generic parser is the only user of the bind-mixer controls, so we
can move the code there and clean up the core helper.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The beep mute switch for ALC268 needs to touch two NIDs, and we used
to apply the bind-mixer stuff. But the use case for ALC268 is fairly
easy to convert to an open-code in a shorter form. Since this is the
only user of the bind-ctls, we can clean up the common helper codes
later.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The comment at endif line was forgotten to be corrected when the
condition was converted to IS_REACHABLE(). Fix it, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rewrite the complex ifdef condition with IS_REACHABLE().
The ifdef in opl4_local.h was without defined(MODLE) check, but this
is likely the oversight. Use IS_REACHABLE() here as well.
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM notifier code is used only by OSS emulation layer, so we can
build it conditionally for reducing the size.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ak4113, ak4114 and ak4117 i2c drivers have some tricky codes to
access the struct fields in the callback. This can be simplified by
replacing the struct fields with the array.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The vxpocket driver is using the explicit cast from the parent class
pointer, but it'll be broken when the structure field randomization is
applied. Use container_of() in a modern manner, instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC299 has no loopback mixer, but the driver still tries to add a beep
control over the mixer NID which leads to the error at accessing it.
This patch fixes it by properly declaring mixer_nid=0 for this codec.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195775
Fixes: 28f1f9b26c ("ALSA: hda/realtek - Add new codec ID ALC299")
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AVR32 is gone. Now it's time to clean up the driver by removing
leftovers that was used by AVR32 related code.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Not calling pm_runtime_enable() means that runtime PM can't be
enabled at all via sysfs. So we definitely need to call it
from somewhere.
Calling it from the driver seems like a bad idea because it
would have to be paired with a pm_runtime_disable() at driver
unload time, otherwise the core gets upset. Also if there's
no LPE audio driver loaded then we couldn't runtime suspend
i915 either.
So it looks like a better plan is to call it from i915 when
we register the platform device. That seems to match how
pci generally does things. I cargo culted the
pm_runtime_forbid() and pm_runtime_set_active() calls from
pci as well.
The exposed runtime PM API is massive an thorougly misleading, so
I don't actually know if this is how you're supposed to use the API
or not. But it seems to work. I can now runtime suspend i915 again
with or without the LPE audio driver loaded, and reloading the
LPE audio driver also seems to work.
Note that powertop won't auto-tune runtime PM for platform devices,
which is a little annoying. So I'm not sure that leaving runtime
PM in "on" mode by default is the best choice here. But I've left
it like that for now at least.
Also remove the comment about there not being much benefit from
LPE audio runtime PM. Not allowing runtime PM blocks i915 runtime
PM, which will also block s0ix, and that could have a measurable
impact on power consumption.
Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Fixes: 0b6b524f39 ("ALSA: x86: Don't enable runtime PM as default")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-2-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>
(cherry picked from commit 183c00350c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The vx222 driver is using the explicit cast from the parent class
pointer, but it'll be broken when the structure field randomization is
applied. Use container_of() in a modern manner, instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This USB driver currently depends on X86 for some undocumented reason.
Since it compiles just fine for arm, we can at least enable compile
testing.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the device-id table and a private flag to determine the device type
(US122 or US144) rather than spreading product-id conditionals
throughout the driver.
This USB driver currently depends on X86 (why?), but we should still add
the missing endianness conversions when accessing the USB
device-descriptor fields.
Compile-tested only.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add missing endianness conversion when using the USB device-descriptor
bcdDevice field when applying the Amanero Combo384 (endianness!) quirk.
Fixes: 3eff682d76 ("ALSA: usb-audio: Support both DSD LE/BE Amanero firmware versions")
Cc: Jussi Laako <jussi@sonarnerd.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the SRM lock check section of code the '&' bitwise operator is
used as part of checking lock status. Functionally the code works
as intended, but the conditional statement is a boolean comparison
so should really use '&&' logical operator instead. This commit
rectifies this discrepancy.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Thinkpad Helix 2 is a tablet PC, the audio is powered by Core M
broadwell-audio and rt286 codec. For all versions of Linux kernel,
the stereo output doesn't work properly when earphones are plugged
in, the sound was coming out from both channels even if the audio
contains only the left or right channel. Furthermore, if a music
recorded in stereo is played, the two channels cancle out each other
out, as a result, no voice but only distorted background music can be
heard, like a sound card with builtin a Karaoke sount effect.
Apparently this tablet uses a combo jack with polarity incorrectly
set by rt286 driver. This patch adds DMI information of Thinkpad Helix 2
to force_combo_jack_table[] and the issue is resolved. The microphone
input doesn't work regardless to the presence of this patch and still
needs help from other developers to investigate.
This is my first patch to LKML directly, sorry for CC-ing too many
people here.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=93841
Signed-off-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Mark Brown <broonie@kernel.org>
The i915 component framework expects the caller to be invoking
snd_hdac_i915_init() from a thread context. Otherwise it results in
lockups on drm side.
So move the registering of component interface and probing of codecs on
this bus to a worker thread.
init_failed in skl structure is not used currently, so renamed to
init_done and used to track the initialization done in worker thread.
Reported-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sodhi, VunnyX <vunnyx.sodhi@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This contains a one-liner change that has a significant impact:
disabling the build of OSS. It's been unmaintained for long time,
and we'd like to drop the stuff. Finally, as the first step, stop
the build. Let's see whether it works without much complaints.
Other than that, there are two small fixes for HD-audio.
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEECxfAB4MH3rD5mfB6bDGAVD0pKaQFAlkVr2YOHHRpd2FpQHN1
c2UuZGUACgkQbDGAVD0pKaQPqRAAoTbIYoB30Wzrg/CraNwTC0ks0pVF1Pjk6mQF
2phnpwbUZ/Hj2bD+4ydlaeNO93pXJHlyvoQwfxlb/tJEg8pVZ2PwyLZ/nfKAGDHg
BJHpGuv3CUvrU/OzZ2xXGfKeiMibhE7Bfjnl/hriztiCNdeEVE6tQU5hRczSUzk8
zgo3fmDsmP4NZqBR9DnrfTsti+HWcclAYKbxaHPxOfVOkKpd5waVQu4AAU5JgBhE
mifvey0QaRUhpDs8ETlDZhvLJICbB6Ybb2l2hK+HyQBwSOSUjHNBXlnsBXpeXUVJ
Ay/hJ4/u0PfeNafxZm66fTEHHTvyXCiCfjStKvIqGkjkAgI73r2H5qrdk4FhyFDI
ovOGMR8j5YKH4smcU13Yx8qoQqmpjNJiL1eplFsRv+BImiIAADH8AMhdKySOQa9/
wmw6qWcwo+LHkxu+l+FCjaQlsZbRhaBmYRnSG4A0IU/lTWhcFk0BYa98Hj/TpjoB
Yo1JmUhYW80h424p0eqV/vl/VDCiUpMct4YcvK3nNDi/1uuLC8qC8jr+qH8Bssg8
9xZjaXDKf3Hf2x7r++kU2xjb1NEWH5WMBFzpXEuN6I+nY/BJG5i/JrXlvWBAG+qZ
Cn3rOAE2ACM9Vs6wtIhaDU7aMoaCb/GlkkmcF7y3XRSmUF53yVICoCNLZ1zFuJrh
Pr2CjJ4=
=Na0H
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains a one-liner change that has a significant impact:
disabling the build of OSS. It's been unmaintained for long time, and
we'd like to drop the stuff. Finally, as the first step, stop the
build. Let's see whether it works without much complaints.
Other than that, there are two small fixes for HD-audio"
* tag 'sound-fix-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
sound: Disable the build of OSS drivers
ALSA: hda: Fix cpu lockup when stopping the cmd dmas
ALSA: hda - Add mute led support for HP EliteBook 840 G3
OSS drivers are left as badly unmaintained, and now we're facing a
problem to clean up the hackish set_fs() usage in their codes. Since
most of drivers have been covered by ALSA, and the others are dead old
and inactive, let's leave them RIP.
This patch is the first step: disable the build of OSS drivers.
We'll eventually drop the whole codes and clean up later.
Note that sound/oss/dmasound is still kept, since it's a completely
different implementation of OSS, and it doesn't suffer from set_fs()
hack. Moreover, the build of ALSA is disabled on M68K by some reason,
thus disabling it shall result in a regression. This one will be
disabled / removed once when we add the support in ALSA side.
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
set_memory_* functions have moved to set_memory.h. Switch to this
explicitly.
Link: http://lkml.kernel.org/r/1488920133-27229-14-git-send-email-labbott@redhat.com
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This typo is quite common. Fix it and add it to the spelling file so
that checkpatch catches it earlier.
Link: http://lkml.kernel.org/r/20170317011131.6881-2-sboyd@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It was a relatively calm development cycle, and no scaring changes are
seen in both core and driver sides. Here are some highlights:
ASoC:
- A new API for hooking up jacks more generically and easily
- Card longname is set based on DMI for a unique UCM profile
- Lots of Intel driver fixes: Atom, Broxton, Skylake and newer chips
- New drivers for Cirrus CS35L35, DIO DIO2125, Everest ES7132,
HiSilicon hi6210, Maxim MAX98927, MT2701 systems with WM8960, Nuvoton
NAU8824, Odroid systems, ST STM32 SAI controllers and x86 systems with
DA7213
HD-audio:
- Many new quirks to support headset for various devices (mostly ASUS
ones) as usual
- Support for dual codecs on some Gigabyte mobos and Lenovo laptop
- Improvement on PCM position reporting for Skylake and newer
FireWire:
- New drivers for MOTU and RME Fireface series
- Updates for Digidesign Digi00x and TASCAM series
- Support for tracepoints
Others:
- USB-audio: improved support for quirk_alias option
- Cleanups, constification allover the places
-----BEGIN PGP SIGNATURE-----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=8RhW
-----END PGP SIGNATURE-----
Merge tag 'sound-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It was a relatively calm development cycle, and no scaring changes are
seen in both core and driver sides. Here are some highlights:
ASoC:
- A new API for hooking up jacks more generically and easily
- Card longname is set based on DMI for a unique UCM profile
- Lots of Intel driver fixes: Atom, Broxton, Skylake and newer chips
- New drivers for Cirrus CS35L35, DIO DIO2125, Everest ES7132,
HiSilicon hi6210, Maxim MAX98927, MT2701 systems with WM8960,
Nuvoton NAU8824, Odroid systems, ST STM32 SAI controllers and x86
systems with DA7213
HD-audio:
- Many new quirks to support headset for various devices (mostly ASUS
ones) as usual
- Support for dual codecs on some Gigabyte mobos and Lenovo laptop
- Improvement on PCM position reporting for Skylake and newer
FireWire:
- New drivers for MOTU and RME Fireface series
- Updates for Digidesign Digi00x and TASCAM series
- Support for tracepoints
Others:
- USB-audio: improved support for quirk_alias option
- Cleanups, constification allover the places"
* tag 'sound-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (299 commits)
ASoC: codec: wm8960: Relax bit clock computation when using PLL
ASoC: codec: wm9860: avoid maybe-uninitialized warning
ASoC: nau8824: leave Class D gain at chip default
ASoC: nau8824: rename controls to match DAPM controls
ASoC: Intel: Skylake: Return negative error code
ASoC: Intel: Skylake: Fix unused variable warning
ASoC: Intel: Skylake: fix uninitialized pointer use
ASoC: sti: Fix error handling if of_clk_get() fails
ASoC: cs4271: configure reset GPIO as output
ASoC: dwc: Disallow building designware_pcm as a module
ALSA: ali5451: fix spelling mistake in "ali_capture_preapre"
ASoC: stm32: add SAI driver
ASoC: stm32: add bindings for SAI
ASoC: Intel: Skylake: Add loadable module support on KBL platform
ASoC: Intel: Skylake: Modify load_lib_ipc arguments for a nowait version
ASoC: Intel: Skylake: Register dsp_fw_ops for kabylake
ASoC: Intel: Skylake: Modify arguments to reuse module transfer function
ASoC: Intel: Skylake: Commonize library load
ASoC: Intel: Skylake: Move sst common initialization to a helper function
ASoC: nau8824: new driver
...
A quiet release for the core, but lots of new drivers this time around:
- A new, generalized, API for hooking up jacks which makes it easier to
write generic machine drivers for simple cases.
- Continuing fixes for issues with the x86 CPU drivers.
- New drivers for Cirrus CS35L35, DIO DIO2125, Everest ES7132,
HiSilicon hi6210, Maxim MAX98927, MT2701 systems with WM8960, Nuvoton
NAU8824, Odroid systems, ST STM32 SAI controllers and x86 systems with
DA7213
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlkH9Q4THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0D24B/4oQ67H01Tcq0ghrIsr/UNQnPi+ywx2
e5nkWNvWTM7gSUDOFjmD3ZM07Gf66IIyiFFSt6w93/lDQaOcGgsmBo9tnujR7ytQ
XXUiE1bvx7liZ09/2Rq7DyDXTpYcFAbxLdWt8uGs72misj0XrVToVFJhl5YcMRBE
qnbV1woxQwIvJ5m+GmbW2NZ8bRCnnsMQbBWCIWOtvSPhtZQlQ+m7waYTVn3/ieGR
cWIHwY4lSZycqaYDWZ+RPFipcAwzKTNt0MiXoCI02EX95275AbIHdWAgrVta04Al
muWP1XTkufO73NFqfvEF+Rrpi69pRCNhAS7TJY++d1moKCYgSpG8bAvD
=W3eF
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.12
A quiet release for the core, but lots of new drivers this time around:
- A new, generalized, API for hooking up jacks which makes it easier to
write generic machine drivers for simple cases.
- Continuing fixes for issues with the x86 CPU drivers.
- New drivers for Cirrus CS35L35, DIO DIO2125, Everest ES7132,
HiSilicon hi6210, Maxim MAX98927, MT2701 systems with WM8960, Nuvoton
NAU8824, Odroid systems, ST STM32 SAI controllers and x86 systems with
DA7213
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=gJJi
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"New drivers:
- add LED support for MT6323 PMIC
- add LED support for Motorola CPCAP PMIC
New features and improvements:
- add LED trigger for all CPUs aggregated which is useful on tiny
boards with more CPU cores than LED pins
- add OF variants of LED registering functions as a preparation for
adding generic support for Device Tree parsing
- dell-led improvements and cleanups, followed by moving it to the
x86 platform driver subsystem which is a more appropriate place for
it
- extend pca9532 Device Tree support by adding the LEDs
'default-state' property
- extend pca963x Device Tree support by adding nxp,inverted-out
property for inverting the polarity of the output
- remove ACPI support for lp3952 since it relied on a non-official
ACPI IDs"
* tag 'leds_for_4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: pca9532: Extend pca9532 device tree support
leds: cpcap: new driver
mfd: cpcap: Add missing include dependencies
leds: lp3952: Use 'if (ret)' pattern
leds: lp3952: Remove ACPI support for lp3952
leds: mt6323: Fix an off by one bug in probe
dt-bindings: leds: Add document bindings for leds-mt6323
leds: Add LED support for MT6323 PMIC
leds: gpio: use OF variant of LED registering function
leds: core: add OF variants of LED registering functions
platform/x86: dell-wmi-led: fix coding style issues
dell-led: move driver to drivers/platform/x86/dell-wmi-led.c
dell-led: remove code related to mic mute LED
platform/x86: dell-laptop: import dell_micmute_led_set() from drivers/leds/dell-led.c
ALSA: hda - rename dell_led_set_func to dell_micmute_led_set_func
ALSA: hda - use dell_micmute_led_set() instead of dell_app_wmi_led_set()
dell-led: remove GUID check from dell_micmute_led_set()
leds/trigger/cpu: Add LED trigger for all CPUs aggregated
A few last minute fixes for v4.11, the STI fix is relatively large but
driver specific and has been cooking in -next for a little while now:
- A fix from Takashi for some suspend/resume related crashes in the
Intel drivers.
- A fix from Mousumi Jana for issues with incorrectly created
enumeration controls generated from topology files which could cause
problems for userspace.
- Fixes from Arnaud Pouliquen for some crashes due to races with the
interrupt handler in the STI driver.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlj/auUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JEJB/9fZoEPm2Flfp9d4tXDmNihyv/STARr
UbIIBxJUsDG2U6nMxv1kTKRk/9puuzDfNjt4giiLyMNDMbh4G5QRbgMF53ryeTuM
8Nqq6PEvhZ4/YftOnh4uD4PmsVKTV8OauQDzZquLPB9/lRF6wLvSskSfZXTsYbv9
Oem4Sop1XzXt68cUIcMHQlwXrhxIaQUHiOS8QfhQXNw1y5xgGB5Rj0ak5fWdn+KY
6j10ldQgrwYSCx4zbqLsS6Fjlo2zdUj/Rn7fQrarzsjQtrZq+k6iYvAWAblkMhWi
7hL/RK4U0konSeo12ftIESDpZFjW2Yi9Q74+4i6soEYbOVTzMam+XMo+
=qmpO
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.11-rc7' into asoc-linus
ASoC: Fixes for v4.11
A few last minute fixes for v4.11, the STI fix is relatively large but
driver specific and has been cooking in -next for a little while now:
- A fix from Takashi for some suspend/resume related crashes in the
Intel drivers.
- A fix from Mousumi Jana for issues with incorrectly created
enumeration controls generated from topology files which could cause
problems for userspace.
- Fixes from Arnaud Pouliquen for some crashes due to races with the
interrupt handler in the STI driver.
# gpg: Signature made Wed 26 Apr 2017 00:27:33 KST
# gpg: using RSA key ADE668AA675718B59FE29FEA24D68B725D5487D0
# gpg: issuer "broonie@kernel.org"
# gpg: key 0D9EACE2CD7BEEBC: no public key for trusted key - skipped
# gpg: key 0D9EACE2CD7BEEBC marked as ultimately trusted
# gpg: key CCB0A420AF88CD16: no public key for trusted key - skipped
# gpg: key CCB0A420AF88CD16 marked as ultimately trusted
# gpg: key 162614E316005C11: no public key for trusted key - skipped
# gpg: key 162614E316005C11 marked as ultimately trusted
# gpg: key A730C53A5621E907: no public key for trusted key - skipped
# gpg: key A730C53A5621E907 marked as ultimately trusted
# gpg: key 276568D75C6153AD: no public key for trusted key - skipped
# gpg: key 276568D75C6153AD marked as ultimately trusted
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>" [ultimate]
# gpg: aka "Mark Brown <broonie@debian.org>" [ultimate]
# gpg: aka "Mark Brown <broonie@kernel.org>" [ultimate]
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>" [ultimate]
# gpg: aka "Mark Brown <broonie@linaro.org>" [ultimate]
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>" [ultimate]
Bitclk is derived from sysclk using bclk_divs.
Sysclk can be derived in two ways:
(1) directly from MLCK
(2) MCLK via PLL
Commit 3c01b9ee2a ("ASoC: codec: wm8960: Relax bit clock
computation")
relaxed bitclk computation when sysclk is directly derived from MCLK.
Lets do the same thing when sysclk is derived via PLL.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new PLL configuration code triggers a harmless warning:
sound/soc/codecs/wm8960.c: In function 'wm8960_configure_clocking':
sound/soc/codecs/wm8960.c:735:3: error: 'best_freq_out' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
wm8960_set_pll(codec, freq_in, best_freq_out);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sound/soc/codecs/wm8960.c:699:12: note: 'best_freq_out' was declared
here
Fix this by reworking the code such that:
1) When there is no PLL freq available return -EINVAL and make
sure *bclk_idx, *dac_idx, *sysclk_idx are initialized with
invalid values.
2) When there is a PLL freq available initialize *bclk_idx,
*dac_idx and *sysclk_idx with correct values and immediately
return the freq available.
Fixes: 84fdc00d51 ("ASoC: codec: wm9860: Refactor PLL out freq search")
Fixes: 303e8954af ("ASoC: codec: wm8960: Stop when a matching PLL freq is found")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove initial configuration of Class D gain for 1R and 2L.
Leave them at the chip default.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: John Hsu <supercraig0719@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename the name of kcontrols to match up the DAPM
widget controls.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: John Hsu <supercraig0719@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
skl_tplg_add_pipe() returned EEXIST instead of negative EEXIST, so fix that
and handle the return value as well.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
With compiler option W=1, we have one more warning in the driver for
'set but unused variable', so remove the unused variable to fix it.
sound/soc/intel/skylake/skl-pcm.c: In function ‘skl_platform_open’:
sound/soc/intel/skylake/skl-pcm.c:954:26: warning: variable ‘runtime’ set but not used [-Wunused-but-set-variable]
struct snd_pcm_runtime *runtime;
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
The error handling in bxt_sst_dsp_init() got changed in a way that
it now derefences an uninitialized pointer when printing a warning
about the device not being found:
sound/soc/intel/skylake/bxt-sst.c: In function 'bxt_sst_dsp_init':
sound/soc/intel/skylake/bxt-sst.c:567:14: error: 'skl' may be used uninitialized in this function [-Werror=maybe-uninitialized]
As we do have a valid device pointer available at the call site,
let's use that instead.
Fixes: 9fe9c71192 ("ASoC: Intel: Skylake: Move sst common initialization to a helper function")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
We intended to return here. The current code has a static checker
warning because we set "ret" but don't use it.
Fixes: 76c2145ded ("ASoC: sti: Add CPU DAI driver for playback")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During reset "refactoring" the output configuration was lost.
This commit repairs sound on EDB93XX boards.
Fixes: 9a397f4 ("ASoC: cs4271: add regulator consumer support")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org> # 4.6+
Designware PCM is an extension to Designware I2S and they are dependent
on each other. For this reason, make Designware PCM a boolean which will
compile with Desigwnare I2S module. The name of the module is not changed
but the name of the files need to be changed.
Also, without this commit we get errors when probbing designware_i2s module
because of unspecified license:
designware_pcm: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
designware_pcm: Unknown symbol __rcu_read_lock (err 0)
designware_pcm: Unknown symbol devm_snd_soc_register_platform (err 0)
designware_pcm: Unknown symbol synchronize_rcu (err 0)
designware_pcm: Unknown symbol __rcu_read_unlock (err 0)
designware_pcm: Unknown symbol snd_soc_set_runtime_hwparams (err 0)
So, this is really needed as a fix.
Fixes: 79361b2b98 ("ASoC: dwc: Add PIO PCM extension")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
trivial fix to spelling mistake in dev_warn message,
"ali_capture_preapre" should be "ali_capture_prepare"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kabylake platform expects modules in a library manifest. After loading
base firmware library manifest is loaded using load library IPC. This is
followed by module load using load multiple modules IPC.
Signed-off-by: Sodhi, VunnyX <vunnyx.sodhi@intel.com>
Signed-off-by: G Kranthi <gudishax.kranthikumar@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kabylake uses code loader dma and wait on notification instead of ipc
reply for load library ipc status. So modify the argument of
skl_sst_ipc_load_library to check on flag to wait for ipc reply.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For audio kabylake is same as skylake except the module load approach.
This patch registers different dsp_fw_ops for kabylake and next patch
adds the module load support for kabylake.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kabylake also uses code loader dma for module load and library load.
skl_transfer_module can be reused. Modify the arguments to include
library index to be passed to lib load ipc and module/lib check to use
correct ipc for lib/module load.
Signed-off-by: G Kranthi <gudishax.kranthikumar@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
request firmware, strip extended manifest and release library changes
are common to kabylake and APL.
So move these common code to utils to be reused in later patches for
kabylake library load.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some skl sst context are not dependent of platform and initializing them
independently for each platform can lead to errors. So optimize by
moving them to a helper function and platform specific init code can
call this.
Signed-off-by: G Kranthi <gudishax.kranthikumar@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for NAU88L24.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: John Hsu <supercraig0719@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lenovo P520/420 build with two codecs.
ALC233 for front panel.
ALC662 for rear panel.
This patch will rename capture name for slove conflicts.
And create a card longname for UCM profile.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few last minute fixes for v4.11, the STI fix is relatively large but
driver specific and has been cooking in -next for a little while now:
- A fix from Takashi for some suspend/resume related crashes in the
Intel drivers.
- A fix from Mousumi Jana for issues with incorrectly created
enumeration controls generated from topology files which could cause
problems for userspace.
- Fixes from Arnaud Pouliquen for some crashes due to races with the
interrupt handler in the STI driver.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlj/auUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JEJB/9fZoEPm2Flfp9d4tXDmNihyv/STARr
UbIIBxJUsDG2U6nMxv1kTKRk/9puuzDfNjt4giiLyMNDMbh4G5QRbgMF53ryeTuM
8Nqq6PEvhZ4/YftOnh4uD4PmsVKTV8OauQDzZquLPB9/lRF6wLvSskSfZXTsYbv9
Oem4Sop1XzXt68cUIcMHQlwXrhxIaQUHiOS8QfhQXNw1y5xgGB5Rj0ak5fWdn+KY
6j10ldQgrwYSCx4zbqLsS6Fjlo2zdUj/Rn7fQrarzsjQtrZq+k6iYvAWAblkMhWi
7hL/RK4U0konSeo12ftIESDpZFjW2Yi9Q74+4i6soEYbOVTzMam+XMo+
=qmpO
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.11
A few last minute fixes for v4.11, the STI fix is relatively large but
driver specific and has been cooking in -next for a little while now:
- A fix from Takashi for some suspend/resume related crashes in the
Intel drivers.
- A fix from Mousumi Jana for issues with incorrectly created
enumeration controls generated from topology files which could cause
problems for userspace.
- Fixes from Arnaud Pouliquen for some crashes due to races with the
interrupt handler in the STI driver.
tas2552_suspend() and tas2552_resume() currently always return success,
even though they may fail.
Fix this behaviour by always propagating the error code.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that quirks can be overridden with a module parameter,
log errors so that non-sensical quirks introduced by mistake
are identified.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The previous patch for adding the quirk module option had a typo in
its info print, which results in a weird output. Also, the parameter
type should be rather unsigned int instead of signed int.
Fixes: 9f2cf73ed6 ("ASoC: bytcr_rt5640: Allow quirk set via module option")
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FE setups of Intel SST bytcr_rt5640 and bytcr_rt5651 drivers carry
the ignore_suspend flag, and this prevents the suspend/resume working
properly while the stream is running, since SST core code has the
check of the running streams and returns -EBUSY. Drop these
superfluous flags for fixing the behavior.
Also, the bytcr_rt5640 driver lacks of nonatomic flag in some FE
definitions, which leads to the kernel Oops at suspend/resume like:
BUG: scheduling while atomic: systemd-sleep/3144/0x00000003
Call Trace:
dump_stack+0x5c/0x7a
__schedule_bug+0x55/0x70
__schedule+0x63c/0x8c0
schedule+0x3d/0x90
schedule_timeout+0x16b/0x320
? del_timer_sync+0x50/0x50
? sst_wait_timeout+0xa9/0x170 [snd_intel_sst_core]
? sst_wait_timeout+0xa9/0x170 [snd_intel_sst_core]
? remove_wait_queue+0x60/0x60
? sst_prepare_and_post_msg+0x275/0x960 [snd_intel_sst_core]
? sst_pause_stream+0x9b/0x110 [snd_intel_sst_core]
....
This patch addresses these appropriately, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org> # v4.1+
Trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bytcr-rt5640 driver has a few quirk setups depending on the board,
where the quirk value is set by DMI matching. When you have a new
device to add the support, you often experience to try the different
quirk by trial-and-error. Or, you may have a development model that
still has no proper DMI string. In either case, you'd need to compile
the driver at each time.
This patch introduces a module option to override the quirk value on
the fly. User can boot like snd-soc-sst-bytcr-rt5640.quirk=0x4004 to
override the default value without recompilation. It's a raw value,
so user needs to check the source code for the meaning of each bit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since recently UCM can pick up a configuration specific to the board
via card longname field, and we introduced a helper function
snd_soc_set_dmi_name() for that. So far, it was used only in one
place (sound/soc/intel/boards/broadwell.c), but it should be more
widely applied.
This patch puts a big hammer for that: it lets snd_soc_register_card()
calling snd_soc_set_dmi_name() unconditionally, so that all x86
devices get the better longname string. This would have no impact for
other systems without DMI support, as snd_soc_set_dmi_name() is no-op
on them.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For systems without DMI, it makes no sense to have the code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the following variables are global:
- card_priv, sample_rate and sample_format
,which is not a good idea as it prevents the usage of multiple
instances.
Make sample_rate and sample_format part of the imx_priv structure
and allocate imx_priv via the standard devm_kzalloc() mechanism
inside the probe function.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This dedicated driver allows to support SoC specific clock
settings and helps to ensure proper number of channels gets
negotiated in multicodec system configurations.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The clock names for the two supported codecs are either
"mi2s-*" name variants generated by code. This naming scheme
does not work for platforms like MSM8660 which has I2S channels
named CODEC_I2S_SPKR (rather than just "MI2S tertiary" and other
repetitive names) and consequently have clocks named
"codec-i2s-spkr-osr-clk" and similar.
Skip the runtime generation of clock names and replace it with
name lookup tables encoded into the variant data.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On the chip the IMON signal is a full 24-bits however normally only
some of the bits will be sent over the bus. The chip provides a field
to select which bits of the IMON will be sent back, this is the only
feedback signal that has this feature.
Add an additional entry to the cirrus,imon device tree property to
allow the IMON scale parameter to be passed.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to use the _safe() version of list_for_each_entry() here because
of the kfree(modules).
Fixes: b8c722ddd5 ("ASoC: Intel: Skylake: Add support for deferred DSP module bind")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The direction argument is of type enum dma_transfer_direction, and
not enum dma_data_direction. The enumeration values are the same
so this did not had an effect in practise.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should not select drivers that depend on I2C when that is disabled,
as it results in a build error:
warning: (SND_SOC_MT2701_WM8960) selects SND_SOC_WM8960 which has unmet direct dependencies (SOUND && !M68K && !UML && SND && SND_SOC && I2C)
sound/soc/codecs/wm8960.c:1469:1: error: data definition has no type or storage class [-Werror]
sound/soc/codecs/wm8960.c:1469:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
Fixes: 8625c1dbd8 ("ASoC: mediatek: Add mt2701-wm8960 machine driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
My static checker complains that if snd_hdac_bus_get_response() returns
-EIO then "res" is uninitialized. Fix this by initializing it to -1 so
that the error is handled correctly.
Fixes: d8c2dab838 ("ASoC: Intel: Add Skylake HDA audio driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
25165f79ad
("ASoC: rsnd: enable clock-frequency for both 44.1kHz/48kHz")
supports both 44.1kHz/48kHz clock-frequency settings for ADG
which will be used for AUDIO_OLKOUTn.
But some board doesn't need it, thus, it is not mandatory.
But, above patch didn't care about the case of "clock-frequency" DT
property was not present.
This patch ignores ADG settings if AUDIO_OLKOUTn was not used.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
[Kuninori: tidyup not to break non AUDIO_OLKOUTn case]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds some workarounds to make Gigabyte GA-AX370 Gaming 5
board working without the conflicts of kctls, etc. In general, the
dual codec configs result in the conflicts of the following stuff:
- Master controls
- Capture controls
- Analog loopback controls
In addition, the auto-mute and the auto-mic can't work well among
multiple codecs.
The current "solution" is to disable all these features, and use UCM
for a better PulseAudio management. For a dedicated UCM profile, the
patch overrides the card longname so that the system an get a unique
profile path.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195305
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Headset microphone does not work out of the box on ASUS Nx51
laptops. This patch fixes it.
Patch tested on Asus N551 laptop. Asus N751 part is not tested, but
according to [1] this laptop uses the same audiosystem.
1. https://bugzilla.kernel.org/show_bug.cgi?id=117781
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195437
Signed-off-by: Mikhail Paulyshka <me@mixaill.tk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In development period for Linux v4.10, ktime_t became an alias of s64,
instead of union. I forgot it. We can just assign zero, instead of usage
of ktime_set(0, 0).
Fixes: 1917429578 ("ALSA: fireface: add transaction support")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in sound/pci/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jaroslav Kysela <perex@perex.cz>
cc: Takashi Iwai <tiwai@suse.com>
cc: alsa-devel@alsa-project.org
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in sound/oss/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jaroslav Kysela <perex@perex.cz>
cc: Takashi Iwai <tiwai@suse.com>
cc: Andrew Veliath <andrewtv@usa.net>
cc: alsa-devel@alsa-project.org
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in sound/isa/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jaroslav Kysela <perex@perex.cz>
cc: Takashi Iwai <tiwai@suse.com>
cc: alsa-devel@alsa-project.org
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in sound/drivers/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
cc: Jaroslav Kysela <perex@perex.cz>
cc: alsa-devel@alsa-project.org
Two functions were introduced for the purpose of tracing but cause warnings
when tracing is disabled:
sound/firewire/motu/amdtp-motu.c:284:13: error: 'copy_message' defined but not used [-Werror=unused-function]
static void copy_message(u64 *frames, __be32 *buffer, unsigned int data_blocks,
sound/firewire/motu/amdtp-motu.c:271:13: error: 'copy_sph' defined but not used [-Werror=unused-function]
static void copy_sph(u32 *frames, __be32 *buffer, unsigned int data_blocks,
Marking them as __maybe_unused will do the right thing here.
Fixes: 17909c1b30 ("ALSA: firewire-motu: add tracepoints for SPH in IEC 61883-1 fashion")
Fixes: c6b0b9e65f ("ALSA: firewire-motu: add tracepoints for messages for unique protocol")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current clock-frequency allows only 1 clock, but ADG can
handle both 44.1kHz/48kHz base clocks. This patch enables these.
On Salvator-X board, AUDIO_CLKOUT which is generated by ADG
is connected to ak4613 MCKI, and it should be synchronized with
LRCK. Thus, we need both 44.1kHz/48kHz base clock-frequency.
Otherwise, either one sounds strange in high frequency sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_mod_make_sure() will be used any situation,
thus, under DEBUG is not realistic.
This patch move it to non DEBUG area
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The HP ZBook 15u G3 has a Conexant CX20724 with mute led on GPIO1 and
mic mute led on GPIO2.
Adding CXT_FIXUP_MUTE_LED_GPIO inspired on patch_realtek's one.
Signed-off-by: Jerónimo Borque <jeronimo@borque.com.ar>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct some minor errors in the register defaults.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently variable i is being for 2 nested for loops. Fix this by
using integer loop counter j for the inside for loop.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Thinkpad Tablet tablet has a similar audio setup as the Intel Braswell
platform.
A quirk is needed to detect the platform and setup the platform data
properly:
Manufacturer: LENOVO
Product Name: 20C1CTO1WW
Version: ThinkPad 10
Manufacturer: LENOVO
Product Name: 20C3001VHH
Version: ThinkPad 10
Manufacturer: LENOVO
Product Name: 20C10024GE
Version: ThinkPad Tablet B
Manufacturer: LENOVO
Product Name: 20359
Version: Lenovo Miix 2 10
Signed-off-by: Nicole Faerber <nicole.faerber@id3p.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are multiple skews of the same Lenovo audio hardware
based on the Realtek RT5670 codec.
Manufacturer: LENOVO
Product Name: 20C1CTO1WW
Version: ThinkPad 10
Manufacturer: LENOVO
Product Name: 20C3001VHH
Version: ThinkPad 10
Manufacturer: LENOVO
Product Name: 20C10024GE
Version: ThinkPad Tablet B
Manufacturer: LENOVO
Product Name: 20359
Version: Lenovo Miix 2 10
For all these devices, the same quirk is used to force
the machine driver to be based on RT5670 instead of RT5640
as indicated by the BIOS.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96691
Tested-by: Nicole Faerber <nicole.faerber@dpin.de>
Tested-by: Viacheslav Ostroukh <v.dev@ostroukh.me>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The /proc/bus/usb devices don't exist anymore, since when we
got rid of usbfs. Those devices are now seen at
/dev/bus/usb.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The rt5514 can get confused and incorrectly detect a start bit if the
SCL/SDA lines happen to both go low and then high again. This
situation has been seen to happen at reboot time and is also
theoretically possible during suspend/resume if the rt5514 keeps power
but we shut down the i2c connection.
When this happens the rt5514 is confused about the state of the i2c
bus and won't recognize its own address. That will lead to the rt5514
incorrectly NAKing the first transfer.
A single i2c transfer to any address should be enough to get the
rt5514 out of this funky state.
It is currently believed that this problem should be fixed in the
rt5514 driver itself because it seems that the i2c controller in the
rt5514 is easily confused. Most i2c devices wouldn't detect a start
bit in this case.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In rt5514_i2c_probe() if the regmap_read(RT5514_VENDOR_ID2) fails then
"val" may be left as uninitialized. Current code relies on "val" not
being RT5514_DEVICE_ID, but that's potentially unsafe.
Let's check for errors from regmap_read() and also explicitly init the
value do we're not passing a possibly uninitialized int to printk.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no reason for rt5514_i2c_driver to be non-static.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA driver for TASCAM FireWire series transfers MIDI messages in system
workqueue. In current design of the driver, applications should wait for
sequence of transmission when they close ALSA rawmidi character devices.
However, when considering design of rawmidi interface, it's preferable
to wait in drain ioctl.
This commit adds support for the drain ioctl to wait for the end of
the transmission.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Units on TASCAM FireWire series handle MIDI messages with support for
running status. Drivers for the series should remember current running
status and transfer valid MIDI messages. For this purpose, current
ALSA driver for the series has some members in its top-level structure.
This is due to better abstraction of async midi port. Nowadays, the
abstraction was localized just for the driver.
This commit moves the members to structure for async midi port.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In current design of ALSA driver for TASCAM FireWire series, initialization
of members in asymc midi port structure is done at device probing. Some of
the members should be initialized every time to use rawmidi devices because
they're changed in sequence of transmission for MIDI messages.
This commit adds a new function to initialize them. Invariant parameters
during object lifetime are kept as is.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA driver for TASCAM FireWire series internally allocates 4 byte buffer
for asynchronous transaction to transfer MIDI messages. However, the buffer
can be allocated with memory object of parent structure.
This commit adds 4 byte array as a member of the structure and obsoletes
the redundant allocation. This is deallocated with memory object of parent
structure.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Units on TASCAM FireWire series receive MIDI messages by asynchronous
transactions on IEEE 1394 bus. Although the transaction is sent to a
certain register, current ALSA driver for this series has a redundant design.
This commit use the same address for the transaction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series uses asynchronous transactions with fixed length
payload for MIDI messaging. On the other hand, ALSA driver for the series
has a redundant design to handle different length of payload.
This commit removes the redundant abstraction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As a result of localization of async midi port, ALSA driver for TASCAM
FireWire series can call helper function directly instead of callback
registration.
This commit removes the redundant design.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In Linux kernel 4.4, firewire-lib got a feature called as 'async midi port'
for transmission of MIDI message via IEEE 1394 asynchronous communication,
however actual consumer of this feature is ALSA driver for TASCAM FireWire
series only. When adding this feature, I assumed that ALSA driver for
Digi00x might also be a consumer, actually it's not.
This commit moves the feature from firewire-lib to firewire-tascam module.
Two minor kernel APIs are removed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In kernel APIs of ALSA control interface, drivers can create a control
element set by a call of snd_ctl_new1() with a template. This template
is known to have const qualifier in general cases.
This commit adds the qualifier to template array, for safer program and
runtime. Application of this change moves the symbol from .data section
to .rodata section.
Cc: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
An abstraction of asynchronous transaction for transmission of MIDI
messages was introduced in Linux v4.4. Each driver can utilize this
abstraction to transfer MIDI messages via fixed-length payload of
transaction to a certain unit address. Filling payload of the transaction
is done by callback. In this callback, each driver can return negative
error code, however current implementation assigns the return value to
unsigned variable.
This commit changes type of the variable to fix the bug.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: <stable@vger.kernel.org> # 4.4+
Fixes: 585d7cba5e ("ALSA: firewire-lib: add helper functions for asynchronous transactions to transfer MIDI messages")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_use_lock_sync() (thus its implementation
snd_use_lock_sync_helper()) has the 5 seconds timeout to break out of
the sync loop. It was introduced from the beginning, just to be
"safer", in terms of avoiding the stupid bugs.
However, as Ben Hutchings suggested, this timeout rather introduces a
potential leak or use-after-free that was apparently fixed by the
commit 2d7d54002e ("ALSA: seq: Fix race during FIFO resize"):
for example, snd_seq_fifo_event_in() -> snd_seq_event_dup() ->
copy_from_user() could block for a long time, and snd_use_lock_sync()
goes timeout and still leaves the cell at releasing the pool.
For fixing such a problem, we remove the break by the timeout while
still keeping the warning.
Suggested-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Geminilake vendor nid is different from other Skylake variants, but rest
of the initialization code is same.
So a variable is added in hdmi_spec to store the platform specific vendor
nid and move the initialization code to a helper function to be used by
both platform specific init.
Fixes: 126cfa2f5e ("ALSA: hda: Add Geminilake HDMI codec ID")
Signed-off-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Jaikrishna Nemallapudi <jaikrishnax.nemallapudi@intel.com>
Cc: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Module at the end of DSP pipeline that needs to be connected to a module
in another pipeline are represented as a PGA(leaf node) and in PGA event
handler these modules are bound/unbounded. Modules other than PGA leaf
can be connected directly or via switch to a module in another pipeline.
Example: reference path.
To support the deferred DSP module bind, following changes are done:
o When the path is enabled, the destination module that needs to be
bound may not be initialized. If the module is not initialized, add
these modules in a deferred bind list.
o When the destination module is initialized, check for these modules
in deferred bind list. If found, bind them.
o When the destination module is deleted, Unbind the modules.
o When the source module is deleted, remove the entry from the deferred
bind list.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need for defining FSL_ESAI_RATES locally as the standard
SNDRV_PCM_RATE_8000_192000 definition can be used instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare snd_kcontrol_new strcutures as const as they are only passed as
an argument to the function snd_ctl_new1. This argument is of type const,
so snd_kcontrol_new structures having this property can be made const too.
Done using Coccinelle:
@r disable optional_qualifier@
identifier x;
position p;
@@
static struct snd_kcontrol_new x@p={...};
@ok@
identifier r.x;
position p;
@@
snd_ctl_new1(&x@p,...)
@bad@
position p != {r.p,ok.p};
identifier r.x;
@@
x@p
@depends on !bad disable optional_qualifier@
identifier r.x;
@@
+const
struct snd_kcontrol_new x;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Declare snd_kcontrol_new strcutures as const as they are only passed as
an argument to the function snd_ctl_new1. This argument is of type const,
so snd_kcontrol_new structures having this property can be made const too.
Done using Coccinelle:
@r disable optional_qualifier@
identifier x;
position p;
@@
static struct snd_kcontrol_new x@p={...};
@ok@
identifier r.x;
position p;
@@
snd_ctl_new1(&x@p,...)
@bad@
position p != {r.p,ok.p};
identifier r.x;
@@
x@p
@depends on !bad disable optional_qualifier@
identifier r.x;
@@
+const
struct snd_kcontrol_new x;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
During packet streaming, maximum length of payload for isochronous packet
is invariable, therefore no need to recalculate. Current ALSA IEC 61883-1/6
engine calls a function to calculate it 8,000 or more times per second
for incoming packet processing.
This commit adds a member to have maximum length of payload into 'struct
amdtp_stream', to reduces the function calls. At first callback from
isochronous context, the length is calculated and stored for later
processing.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Per feedback from Mark Brown, this patch updates the hi6210-i2s
driver to use devm_snd_soc_register_component which simplifies
the logic a bit.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown suggested a style change to use break in the final
default of a switch statement, so this patch addresses that.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch addresses feedback from Mark Brown, adding a few
extra error returns in cases that shouldn't happen
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the case of error in tas2552_codec_probe() we should better
propagate the real error code instead of always returning '-EIO'.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing enum texts store in soc_enum.
Signed-off-by: Mousumi Jana <mousumix.jana@intel.com>
Signed-off-by: Pardha Saradhi K <pardha.saradhi.kesapragada@intel.com>
Signed-off-by: Kranthikumar, GudishaX <gudishax.kranthikumar@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now, we can use .set_jack callback function on codec level. So we
don't need export rt5665_set_jack_detect.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MOTU units transfer/receive messages in each data block of their
isochronous packet payload. A part of content in the message is cleard for
MIDI message transmission, while the rest is unknown yet. Additional
features are required to assist users and developers to reveal the
details.
This commit adds tracepoints for the purpose. The tracepoints are designed
for MOTU's protocol version 2 and 3 (Protocol version 1 is not upstreamed
yet). In the tracepoints, events are probed to gather first two 24 bit
data chunks of each data block. The chunks are formatted into elements
of 64 bit array with padding in MSB.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unique protocol is used for MOTU FireWire series. In this protocol,
data block format is not compliant to AM824 in IEC 61883-1/6. Each of
the data block consists of 24 bit data chunks, except for a first
quadlet. The quadlet is used for source packet header (SPH) described
in IEC 61883-1.
The sequence of SPH seems to represent presentation timestamp
corresponding to included data. Developers have experienced that invalid
sequence brings disorder of units in the series.
Unfortunately, current implementation of ALSA IEC 61883-1/6 engine and
firewire-motu driver brings periodical noises to the units at sampling
transmission frequency based on 44.1 kHz. The engine generates the SPH with
even interval and this mechanism seems not to be suitable to the units.
Further work is required for this issue and infrastructure is preferable
to assist the work.
This commit adds tracepoints for the purpose. In the tracepoints, events
are probed to gather the SPHs from each data blocks.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unique protocol is used for RME Fireface series. In this protocol,
payload format for isochronous packet is not compliant to CIP in
IEC 61883-1/6. The packet includes data blocks just with data channels,
without headers and any metadata.
In previous commits, ALSA IEC 61883-1/6 engine supports this protocol.
However, tracepoints are not supported yet, unlike implementation for
IEC 61883-1/6 protocol. This commit adds support of tracepoints for
the protocol.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce the "lrclk-strength" property to allow LRCLK pad drive strength
to be changed via device tree.
When running a stress playback loop test on a mx6dl wandboard channel
swap can be noticed on about 10% of the times.
While debugging this issue I noticed that when probing the SGTL5000
LRCLK pin with the scope the swap did not happen. After removing
the probe the swap started to happen again.
After changing the LRCLK pad drive strength to the maximum value the
issue is gone.
Same fix works on a mx6dl Colibri board as well.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are many codecs with the capability of jack detection. Usually,
we create a jack on machine driver but there is no common function for
machine driver to deliver the jack pointer to codec driver.
snd_soc_codec_set_jack can be used for delivering the jack pointer to
codec driver and enable the jack detection function. To make it work,
codec driver need to define a callback function to receive the jack
pointer and do all necessary procedure for enabling jack detection.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for hi6210 i2s controller found on hi6220 boards.
Signed-off-by: Andy Green <andy.green@linaro.org>
[jstultz: Forward ported to mainline, fairly major rework
based on suggestions from Mark Brown]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Code can be simplified by using the standard tolower() funtion.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The comment for the FSLSSI_I2S_RATES definition states that the
driver currently only supports I2S slave mode, which is no longer
correct.
As FSLSSI_I2S_RATES is the same as the standard SNDRV_PCM_RATE_CONTINUOUS,
just remove its definition and its comments to make the code simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Another preliminary patch for the dual-codec support: since the
support of vmaster over multiple codecs is difficult, simply disable
it by a new flag to hda_codec struct. A new user hint is added as
well for consistency.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a preliminary patch for a smooth multi-codec support, and it
introduces a new flag, force_pin_prefix, to struct hda_codec.
This flag is used to force to add the pin location prefix to each
input pin. For example, when there is only one microphone pin,
usually the auto-parser assigns the string "Mic". With this flag on,
it'll be like "Front Mic". Also, the creation of "Master" or "PCM"
playback volume for a single pin is suppressed, too.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195305
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some Intel platforms, the audio clock may not be set correctly
with initial setting. This will cause the audio playback/capture
rates wrong.
This patch checks the audio clock setting and will set it to a
proper value if it is set incorrectly.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188411
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch refines the definition of AZX_MLCTL_SPA and AZX_MLCTL_CPA
and add more definitions of ML registers
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With RTlinux a race condition has been found that leads to NULL ptr crash:
- On CPU 0: uni_player_irq_handler is called to treat XRUN
"(player->state == UNIPERIF_STATE_STOPPED)" is FALSE so status is checked,
dev_err(player->dev, "FIFO underflow error detected") is printed
and then snd_pcm_stream_lock should be called to lock stream for stopping.
- On CPU 1: application stop and close the stream.
Issue is that the stop and shutdown functions are executed while
"FIFO underflow error detected" is printed.
So when CPU 0 calls snd_pcm_stream_lock, player->substream is already null.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using an external boost supply the PDN_DONE bit is not set, update
the handling in this case to use to use an appropriate fixed delay.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Shorten the time it takes to power down the amp by disabling the volume
ramp whilst doing the final shutdown. The driver has already muted the
amplifier at this stage so doing the volume ramp serves no purpose.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When a matching PLL freq is found, searching continues even this is
not necessary. The problem was introduced with the following refactoring
commit 84fdc00d51 ("ASoC: codec: wm9860: Refactor PLL out freq search)
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using rsnd_kctrl_new_m/s/e function,
but the differences are very few.
This patch merge these rsnd_kctrl_new_m/s/e into rsnd_kctrl_new
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current src->convert_rate will be set on .hw_param, and
be reset on .quit timing.
But, .hw_param will not be called again if user did Ctrl-Z + fg.
It should be reset on initial of .hw_param to keep its value.
Here, ctu.c already do this.
This patch solves this issue, other wise, MIXed sound will be
strange if user did like below.
> aplay -D plughw:0,0 sound_44100.wav &
> aplay -D plughw:0,1 sound_96000.wav
> Ctrl-Z
> fg # 96kHz will be played as 44.1kHz
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In ALSA firewire stack, some AV/C commands are supported, including
vendor's extensions. Drivers includes response parser of each command,
according to its requirements, while the parser is written with loose
fashion in two points; error check and length check. This doesn't cause
any issues such as kernel corruption, but should be improved.
This commit modifies evaluations of return value on each parsers.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In protocol version 3, drivers can read current sampling clock status from
register 0x'ffff'f000'0b14. 8 bits of LSB of this register represents type
of signal as source of clock.
Current driver code includes invalid bitshift to handle the parameter. This
commit fixes the bug.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 5992e30034 ("ALSA: firewire-motu: add support for MOTU 828mk3 (FireWire/Hybrid) as a model with protocol version 3")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At a commit 6c29230e2a ("ALSA: oxfw: delayed registration of sound
card"), ALSA oxfw driver fails to handle SCS.1m/1d, due to -EBUSY at a call
of snd_card_register(). The cause is that the driver manages to register
two rawmidi instances with the same device number 0. This is a regression
introduced since kernel 4.7.
This commit fixes the regression, by fixing up device property after
discovering stream formats.
Fixes: 6c29230e2a ("ALSA: oxfw: delayed registration of sound card")
Cc: <stable@vger.kernel.org> # 4.7+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For digi00x series, asynchronous transaction is not used to transfer MIDI
messages to/from control surface. One of transction handlers in my previous
work loses its practical meaning.
This commit removes the handler. I note that unit of console type
transfers 0x00001000 to registered address of host space when switching
to 'standalone' mode. Then the unit generates bus reset.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At a commit c5fcee0373 ("ALSA: firewire-digi00x: add MIDI operations for
MIDI control port"), I described that MIDI messages for control surface is
transferred by a different way from the messages for physical ports.
However, this is wrong. MIDI messages to/from all of MIDI ports are
transferred by isochronous packets.
This commit removes codes to transfer MIDI messages via asynchronous
transaction, from MIDI handling layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At a commit 9dc5d31cdc ("ALSA: firewire-digi00x: handle MIDI messages in
isochronous packets"), a functionality to handle MIDI messages on
isochronous packet was supported. But this includes some of my
misunderstanding. This commit is to fix them.
For digi00x series, first data channel of data blocks in rx/tx packet
includes MIDI messages. The data channel has 0x80 in 8 bit of its MSB,
however it's against IEC 61883-6. Unique data format is applied:
- Upper 4 bits of LSB represent port number.
- 0x0: port 1.
- 0x2: port 2.
- 0xe: console port.
- Lower 4 bits of LSB represent the number of included MIDI message bytes;
0x0/0x1/0x2.
- Two bytes of middle of this data channel have MIDI bytes.
Especially, MIDI messages from/to console surface are also transferred by
isochronous packets, as well as physical MIDI ports.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Digi00x series includes two types of unit; rack and console. As long as
reading information on config rom of Digi 002 console, 'MODEL_ID' field
has a different value from the one on Digi 002 rack.
We've already got a test report from users with Digi 003 rack. We can
assume that console type and rack type has different value in the field.
This commit adds a device entry for console type. For following commits,
this commit also adds a member to 'struct snd_digi00x' to identify console
type.
$ cd linux-firewire-utils/src
$ python2 ./crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 0404f9d0 bus_info_length 4, crc_length 4, crc 63952
404 31333934 bus_name "1394"
408 60647002 irmc 0, cmc 1, isc 1, bmc 0, cyc_clk_acc 100, max_rec 7 (256)
40c 00a07e00 company_id 00a07e |
410 00a30000 device_id 0000a30000 | EUI-64 00a07e0000a30000
root directory
-----------------------------------------------------------------
414 00058a39 directory_length 5, crc 35385
418 0c0043a0 node capabilities
41c 04000001 hardware version
420 0300a07e vendor
424 81000007 --> descriptor leaf at 440
428 d1000001 --> unit directory at 42c
unit directory at 42c
-----------------------------------------------------------------
42c 00046674 directory_length 4, crc 26228
430 120000a3 specifier id
434 13000001 version
438 17000001 model
43c 81000007 --> descriptor leaf at 458
descriptor leaf at 440
-----------------------------------------------------------------
440 00055913 leaf_length 5, crc 22803
444 000050f2 descriptor_type 00, specifier_ID 50f2
448 80000000
44c 44696769
450 64657369
454 676e0000
descriptor leaf at 458
-----------------------------------------------------------------
458 0004a6fd leaf_length 4, crc 42749
45c 00000000 textual descriptor
460 00000000 minimal ASCII
464 44696769 "Digi"
468 20303032 " 002"
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface 400 is a second model of RME Fireface series, released in 2006.
This commit adds support for this model.
This model supports 8 analog channels, 2 S/PDIF channels and 8 ADAT
channels in both of tx/rx packet. The number of ADAT channels differs
depending on each mode of sampling transmission frequency.
$ python2 linux-firewire-utils/src/crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 04107768 bus_info_length 4, crc_length 16, crc 30568 (should be 61311)
404 31333934 bus_name "1394"
408 20009002 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 0, max_rec 9 (1024)
40c 000a3501 company_id 000a35 |
410 1bd0862a device_id 011bd0862a | EUI-64 000a35011bd0862a
root directory
-----------------------------------------------------------------
414 000485ec directory_length 4, crc 34284
418 03000a35 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 8d000006 --> eui-64 leaf at 438
424 d1000001 --> unit directory at 428
unit directory at 428
-----------------------------------------------------------------
428 000314c4 directory_length 3, crc 5316
42c 12000a35 specifier id
430 13000002 version
434 17101800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 000261a8 leaf_length 2, crc 25000
43c 000a3501 company_id 000a35 |
440 1bd0862a device_id 011bd0862a | EUI-64 000a35011bd0862a
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds hwdep interface so as the other drivers for audio and
music units on IEEE 1394 have.
This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds PCM functionality to transmit/receive PCM frames on
isochronous packet streaming. This commit enables userspace applications
to start/stop packet streaming via ALSA PCM interface.
Sampling rate requested by applications is used as sampling transmission
frequency of IEC 61883-1/6packet streaming. As I described in followed
commits, units in this series manages sampling clock frequency
independently of sampling transmission frequency, and they supports
resampling between their packet streaming/data block processing layer and
sampling data processing layer. This commit take this driver to utilize
these features for usability.
When internal clock is selected as source signal of sampling clock, this
driver allows user space applications to start PCM substreams at any rate
which packet streaming engine supports as sampling transmission frequency.
In this case, this driver expects units to perform resampling PCM frames
for rx/tx packets when sampling clock frequency and sampling transmission
frequency are mismatched. This is for daily use cases.
When any external clock is selected as the source signal, this driver
gets configured sampling rate from units, then restricts available
sampling rate to the rate for PCM applications. This is for studio use
cases.
Models in this series supports 64.0/128.0 kHz of sampling rate, however
these frequencies are not supported by IEC 61883-6 as sampling transmission
frequency. Therefore, packet streaming engine of ALSA firewire stack can't
handle them. When units are configured to use any external clock as source
signal of sampling clock and one of these unsupported rate is configured
as rate of the sampling clock, this driver returns EIO to user space
applications.
Anyway, this driver doesn't voluntarily configure parameters of sampling
clock. It's better for users to work with appropriate user space
implementations to configure the parameters in advance of usage.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds management functionality for packet streaming.
As long as investigating Fireface 400, there're three modes depending
on sampling transmission frequency. The number of data channels in each
data block is different depending on the mode. The set of available
data channels for each mode might be different for each protocol and
model.
The length of registers for the number of isochronous channel is just
three bits, therefore 0-7ch are available.
When bus reset occurs on IEEE 1394 bus, the device discontinues to
transmit packets. This commit aborts PCM substreams at bus reset handler.
As I described in followed commits, The device manages its sampling clock
independently of sampling transmission frequency against IEC 61883-6.
Thus, it's a lower cost to change the sampling transmission frequency,
while data fetch between streaming layer and DSP require larger buffer
for resampling. As a result, device latency might tend to be larger than
ASICs for IEC 61883-1/6 such as DM1000/DM1100/DM1500 (BeBoB),
DiceII/TCD2210/TCD2220/TCD3070 and OXFW970/971.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating Fireface 400, format of payload of each
isochronous packet is not IEC 61883-1/6, thus its format of data block
is not AM824. The remarkable points of the format are:
* The payload just consists of some data channels of quadlet size without
CIP header.
* Each data channels includes data aligned to little endian order.
* One data channel consists of two parts; 8 bit ancillary field and 24 bit
PCM frame.
Due to lack of CIP headers, rx/tx packets include no CIP headers and
different way to check packet discontinuity. For tx packet, the ancillary
field is used for counter. However, the way of counting is different
depending on positions of data channels. At 44.1 kHz, ancillary field in:
* 1st/6th/9th/10th/14th/17th data channels: not used for this purpose.
* 2nd/18th data channels: incremented every data block (0x00-0xff).
* 3rd/4th/5th/11th/12th/13th data channels: incremented every 256 data
blocks (0x00-0x07).
* 7th/8th/15th/16th data channels: incremented per the number of data
blocks in a packet. The increment can occur per packet (0x00-0xff).
For tx packet, tag of each isochronous packet is used for this purpose.
The value of tag cyclically changes between 0, 1, 2 and 3 in this order.
The interval is different depending on sampling transmission frequency.
At 44.1/48.0 kHz, it's 256 data blocks. At 88.2 kHz, it's 96 data blocks.
The number of data blocks in tx packet is exactly the same as
SYT_INTERVAL. There's no empty packet or no-data packet, thus the
throughput is not 8,000 packets per sec. On the other hand, the one in
rx packet is 8,000 packets per sec, thus the number of data blocks is
different between each packet, depending on sampling transmission
frequency:
* 44.1 kHz: 5 or 6
* 48.0 kHz: 5 or 6 or 7
* 88.2 kHz: 10 or 11 or 12
This commit adds data processing layer to satisfy the above specification
in a policy of 'best effort'. Although PCM frames are handled for
intermediate buffer to user space, the ancillary data is not handled at all
to reduce CPU usage, thus counter is not checked. 0 is always used for tag
of isochronous packet. Furthermore, the packet streaming layer is
responsible for calculation of the number of data blocks for each packet,
thus it's not exactly the same sequence from the above observation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating Fireface 400, IEC 61883-1/6 is not applied to
its packet streaming protocol. Remarks of the specific protocol are:
* Each packet doesn't include CIP headers.
* 64,0 and 128,0 kHz are supported.
* The device doesn't necessarily transmit 8,000 packets per second.
* 0, 1, 2, 3 are used as tag for rx isochronous packets, however 0 is
used for tx isochronous packets.
On the other hand, there's a common feature. The number of data blocks
transferred in a second is the same as sampling transmission frequency.
Current ALSA IEC 61883-1/6 engine already has a method to calculate it and
this driver can utilize it for rx packets, as well as tx packets.
This commit adds support for the transferring protocol. CIP_NO_HEADERS
flag is newly added. When this flag is set:
* Both of 0 (without CIP header) and 1 (with CIP header) are used as tag
to handle incoming isochronous packet.
* 0 (without CIP header) is used as tag to transfer outgoing isochronous
packet.
* Skip CIP header evaluation.
* Use unique way to calculate the quadlets of isochronous packet payload.
In ALSA PCM interface, 128.0 kHz is not supported, and the ALSA
IEC 61883-1/6 engine doesn't support 64.0 kHz. These modes are dropped.
The sequence of rx packet has a remarkable quirk about tag. This will be
described in later commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Audio and music units of RME Fireface series use its own protocol for
isochronous packets to transfer data. This protocol requires ALSA IEC
61883-1/6 engine to have alternative functions.
This commit is a preparation for the protocol.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Drivers can retrieve the state and configuration of clock by read
transactions.
This commit allows protocol abstraction layer to to dump the
information for debugging, via proc interface.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In previous commit, fireface driver supports unique transaction mechanism
for MIDI feature. This commit adds MIDI functionality for userspace
applications.
As I wrote in a followed commit, user space applications get some
requirement from this driver. It should not touch a register to which
units transmit MIDI messages. It should configure a register in which
MIDI transmission is controlled.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating Fireface 400, MIDI messages are transferred by
asynchronous communication over IEEE 1394 bus.
Fireface 400 receives MIDI messages by write transactions to two addresses;
0x'0000'0801'8000 and 0x'0000'0801'9000. Each of two seems to correspond to
MIDI port 1 and 2.
Fireface 400 transfers MIDI messages by write transactions to certain
addresses which configured by drivers. The drivers can decide upper 4 byte
of the addresses by write transactions to 0x'0000'0801'03f4. For the rest
part of the address, drivers can select from below options:
* 0x'0000'0000
* 0x'0000'0080
* 0x'0000'0100
* 0x'0000'0180
Selected options are represented in register 0x'0000'0801'051c as bit
flags. Due to this mechanism, drivers are restricted to use addresses on
'Memory space' of IEEE 1222, even if transactions to the address have
some side effects.
This commit adds transaction support for MIDI messaging, based on my
assumption that the similar mechanism is used on the other protocols. To
receive asynchronous transactions, the driver allocates a range of address
in 'Memory space'. I apply a strategy to use 0x'0000'0000 as lower 4 byte
of the address. When getting failure from Linux FireWire subsystem, this
driver retries to allocate addresses.
Unfortunately, read transaction to address 0x'0000'0801'051c returns zero
always, however write transactions have effects to the other features such
as status of sampling clock. For this reason, this commit delegates a task
to configure this register to user space applications. The applications
should set 3rd bit in LSB in little endian order.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As of 2016, RME discontinued its Fireface series, thus it's OK for us
to focus on released firmwares to drive known units.
As long as investigating Fireface 400 with Windows driver and comparing
the result to FFADO implementation, I can see these firmwares have
different register assignments. On the other hand, according to manuals
of each models, features relevant to packet streaming seem to be common,
because GUIs for these models have the same options. It's reasonable to
assume an abstraction layer of protocols to communicate to each models.
This commit adds the abstraction layer for the protocols. This layer
includes some functions to operate common features of models in this
series.
In IEC 61883-1/6, the sequence of packet can transfer timing information
to synchronize receivers to transmitters. Units of each node on IEEE 1394
bus can generate transmitter's timing clock by handling value of SYT field
in CIP header with high-precision clock. For audio and music units on
IEEE 1394 bus, this recovered clock is designed to used for sampling clock
to capture/generate PCM frames on DSP/ADC/DAC. (Actually, in this world,
there's no units to implement this specification as is, as long as I
know).
Fireface series doesn't use this mechanism. Besides, It doesn't use
isochronous packet with CIP header. It uses internal crystal unit as its
initial sampling clock. When detecting input signals which can be
available for sampling clock (e.g. ADAT input), drivers can configure
units to use the signals as source of sampling clock. When something goes
wrong, e.g. frequency mismatching between the signal and configured value,
units fallback to the other detected signals alternatively. When detecting
no alternatives, internal crystal unit is used as source of sampling
clock. On manual of Fireface 400, this mechanism is described as
'Autosync'.
On the units, packet streaming is controlled by write transactions to
certain registers. Format of the packet, e.g. the number of data channels
in a data block, is also configured by the same manner. For this purpose,
.begin_session and .finish_session is added.
The remarkable point of this protocol is to allow drivers to configure
arbitrary sampling transmission frequency; e.g. 12.345 Hz. As long as I
know, there's no actual DAC/ADC chips which support this kind of
capability. I think a pair of packet streaming layer and data block
processing layer is isolated from sampling data processing layer in a
point of governed clock. In short, between these parts, resampling layer
exists. Actually, for Fireface 400, write transactions to
0x'0000'8010'051c has an effect to change sampling clock frequency with
base frequencies (32.0/44.1/48.0 kHz) and its multipliers (x2/x4),
regardless of sampling transmission frequency.
For this reason, the abstraction layer doesn't handle parameters for
sampling clock. Instead, each implementation of .begin_session is
expected to configure sampling transmission frequency.
For packet streaming layer, it's enough to get current selection of
source signals for the sampling clock and its frequency. In the
abstraction layer, when internal crystal is selected, drivers can sets
arbitrary sampling frequency, else they should follow configured
frequency. For this purpose, .get_clock is added.
Drivers are allows to bank up data fetching from a pair of packet
streaming/data block processing layer and sampling data processing layer.
This feature seems to suppress noises at starting/stopping packet
streaming. For this purpose, .switch_fetching_mode is added.
As I described in the above, units have remarkable mechanism to manage
sampling clock and process sampling data. For debugging purpose,
.dump_sync_status and .dump_clock_config are added. I don't have a need
to common interface to represent the status and configuration,
developers can add actual implementation of the abstraction layer as they
like.
Unlike PCM frames, MIDI messages are transferred by asynchronous
communication over IEEE 1394 bus, thus target addresses are important for
this feature. The .midi_high_addr_reg, .midi_rx_port_0_reg and
.midi_rx_port_1_reg are for this purpose. I'll describe them in following
commit.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
RME Fireface series has several models and their specifications are
different. Currently, we find no way to retrieve the specifications
from actual devices and need to implement them in this driver.
This commit adds a structure to describe model specific data. This
structure has an identical name for each unit, and maximum number of
data channels in each mode. I'll describe about the mode in following
commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just after appearing on IEEE 1394 bus, this unit generates several bus
resets. This is due to loading firmware from on-board flash memory and
initialize hardware. It's better to postpone sound card registration.
This commit schedules workqueue to process actual probe processing
2 seconds after the last bus-reset. The card instance is kept at unit
probe callback and released at card free callback. Therefore, when the
actual probe processing fails, the memory block is wasted. This is due to
simplify driver implementation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new driver for RME Fireface series. This commit just
creates/removes card instance according to IEEE 1394 bus event. More
functions will be added in following commits.
Three types of firmware have released by RME GmbH; for Fireface 400, for
Fireface 800 and for UCX/802/UFX. It's reasonable that these models use
different protocol for communication. Currently, I've investigated
Fireface 400 and nothing others.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current ALSA SoC Sound Card basically consists of CPU/Codec/Platform
components. If system uses Kernel modules, we can disable these drivers
by using rmmod command. In such case, we can't disable
CPU/Codec/Platform driver without disabling Sound Card driver.
But on the other hand, we can disable these drivers by using unbind
command. In such case, we can disable these drivers randomly.
In this case, we can create dirty Sound Card which is missing necessary
components.
(1) If user disabled Sound Card first, but did nothing to other drivers,
user can't use Sound because Sound Card is no longer exists.
(2) If user disabled CPU/Codec/Platform driver randomly, but did nothing
to Sound Card, user still be able to use Sound Card, because dirty Sound
Card still exists. In this case, Sound system will be crashed if user
started sound playback/capture. But we can't block such random unbind
now.
To avoid Sound Card crash in (2) case, we need to unregister Sound Card
whenever CPU/Codec/Platform component were unregistered.
This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a separate function for deriving (sysclk, lrclk, bclk)
when the clock is auto or pll.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-rt5677.ko | grep alias
alias: i2c:RT5677CE:00
alias: i2c:rt5676
alias: i2c:rt5677
After this patch:
$ modinfo sound/soc/codecs/snd-soc-rt5677.ko | grep alias
alias: of:N*T*Crealtek,rt5677C*
alias: of:N*T*Crealtek,rt5677
alias: i2c:RT5677CE:00
alias: i2c:rt5676
alias: i2c:rt5677
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-wm8978.ko | grep alias
alias: i2c:wm8978
After this patch:
$ modinfo sound/soc/codecs/snd-soc-wm8978.ko | grep alias
alias: i2c:wm8978
alias: of:N*T*Cwlf,wm8978C*
alias: of:N*T*Cwlf,wm8978
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-uda1380.ko | grep alias
alias: i2c:uda1380
After this patch:
$ modinfo sound/soc/codecs/snd-soc-uda1380.ko | grep alias
alias: of:N*T*Cnxp,uda1380C*
alias: of:N*T*Cnxp,uda1380
alias: i2c:uda1380
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-sta529.ko | grep alias
alias: i2c:sta529
After this patch:
$ modinfo sound/soc/codecs/snd-soc-sta529.ko | grep alias
alias: of:N*T*Cst,sta529C*
alias: of:N*T*Cst,sta529
alias: i2c:sta529
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-ssm4567.ko | grep alias
alias: acpi*:INT343B:*
alias: i2c:ssm4567
After this patch:
$ modinfo sound/soc/codecs/snd-soc-ssm4567.ko | grep alias
alias: acpi*:INT343B:*
alias: of:N*T*Cadi,ssm4567C*
alias: of:N*T*Cadi,ssm4567
alias: i2c:ssm4567
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-rt5645.ko | grep alias
alias: acpi*:10EC3270:*
alias: acpi*:10EC5640:*
alias: acpi*:10EC5650:*
alias: acpi*:10EC5648:*
alias: acpi*:10EC5645:*
alias: i2c:rt5650
alias: i2c:rt5645
After this patch:
$ modinfo sound/soc/codecs/snd-soc-rt5645.ko | grep alias
alias: of:N*T*Crealtek,rt5650C*
alias: of:N*T*Crealtek,rt5650
alias: of:N*T*Crealtek,rt5645C*
alias: of:N*T*Crealtek,rt5645
alias: acpi*:10EC3270:*
alias: acpi*:10EC5640:*
alias: acpi*:10EC5650:*
alias: acpi*:10EC5648:*
alias: acpi*:10EC5645:*
alias: i2c:rt5650
alias: i2c:rt5645
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver has an OF device ID table but the struct i2c_driver
.of_match_table field is not set.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
While there, move the MODULE_DEVICE_TABLE(i2c, max9867_i2c_id) just next
to the I2C device table declaration, for consistency with other drivers.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-max9867.ko | grep alias
alias: i2c:max9867
After this patch:
$ modinfo sound/soc/codecs/snd-soc-max9867.ko | grep alias
alias: i2c:max9867
alias: of:N*T*Cmaxim,max9867C*
alias: of:N*T*Cmaxim,max9867
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Newer ADSP2V2 codecs include a memory protection unit that can
be set to trap illegal accesses. When enabling an ADSPV2 core we
must configure the memory region traps so that the firmware can
access its own memory.
Signed-off-by: Mayuresh Kulkarni <mkulkarni@opensource.wolfsonmicro.com>
Signed-off-by: Nikesh Oswal <Nikesh.Oswal@wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adds support for ADSP2V2 cores. Primary differences are that
they use a 32-bit register map compared to the 16-bit register
map of ADSP2V1, and there are some changes to clocking control.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new controls will give user the ability to route the left PDM channel
data to the right headset/handsfree DAC.
HS mono to stereo switch: PDM channel 1 (or mono) data to both HS DAC.
HF mono to stereo switch: PDM channel 3 data to both HF DAC.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Apply the same methods to obtain the current stream position as ASoC
Intel SKL driver uses. It reads the position from DPIB for a playback
stream while it still reads from the position buffer for a capture
stream. For a capture stream, some ugly workaround is needed to
settle down the inconsistent position.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The macros _snd_hdac_chip_read() and *_write() expand to different
types (b,w,l) per their argument. They were thought to be used only
internally for other snd_hdac_chip_*() macros, but in some situations
we need to call these directly, and they are way too ugly.
Instead of saving a few lines, we just write these macros explicitly
with the types, so that they can be used in a saner way.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With the previous unsigned long value clang generates warnings like
this:
sound/pci/hda/patch_ca0132.c:860:37: error: implicit conversion from
'unsigned long' to 'u32' (aka 'unsigned int') changes value from
18446744073709551615 to 4294967295 [-Werror,-Wconstant-conversion]
spec->curr_chip_addx = (res < 0) ? ~0UL : chip_addx;
~ ^~~~
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai
Andy Shevchenko
Ville Syrjälä
Johan Hovold
Adam Thomson
Yifeng Li
Vinod Koul
Linus Torvalds
Jeeja KP
Laura Abbott
Stephen Boyd
Florin Tudorache
Mark Brown
Daniel Baluta
John Hsu
Guneshwor Singh
Arnd Bergmann
Dan Carpenter
Alexander Sverdlin
Jose Abreu
Colin Ian King
olivier moysan
Sodhi, VunnyX
Subhransu S. Prusty
G Kranthi
Kailang Yang
Fabio Estevam
Pierre-Louis Bossart
Sylwester Nawrocki
Linus Walleij
Charles Keepax
Stefan Agner
Marek Vasut
kbuild test robot
Mikhail Paulyshka
Takashi Sakamoto
David Howells
Kuninori Morimoto
Jerónimo Borque
Nicole Faerber
Mauro Carvalho Chehab
Douglas Anderson
Ander Conselvan De Oliveira
Bhumika Goyal
John Stultz
Mousumi Jana
Bard Liao
Andy Green
Libin Yang
Arnaud Pouliquen
Ryan Lee
Javier Martinez Canillas
Mayuresh Kulkarni
Richard Fitzgerald
Peter Ujfalusi
Matthias Kaehlcke