The value hwirq is received from DT. If it exceeds the maximum
valid value it causes the code to address unexisting irq chips
reading outside the array boundary.
Check the value of hwirq before using it.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220606162757.415354-4-antonio.borneo@foss.st.com
The driver has to mask/unmask the corresponding flag in the
Interrupt Mask Register (IMR).
This is already done for configurable event, while direct events
only forward the mask/unmask request to the parent.
Use the existing stm32_exti_h_mask()/stm32_exti_h_unmask() for
direct events too.
Signed-off-by: Loic Pallardy <loic.pallardy@foss.st.com>
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220606162757.415354-3-antonio.borneo@foss.st.com
When there is no parent, there is no specific action to do in
stm32-exti irqchip. In such case, it's incorrect returning an
error.
Let irq_set_affinity to return IRQ_SET_MASK_OK_DONE when there is
no parent.
Signed-off-by: Ludovic Barre <ludovic.barre@foss.st.com>
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220606162757.415354-2-antonio.borneo@foss.st.com
The T-HEAD PLIC ignores additional edges seen while an edge-triggered
interrupt is being handled. Because of this behavior, the driver needs
to complete edge-triggered interrupts in the .irq_ack callback before
handling them, instead of in the .irq_eoi callback afterward. Otherwise,
it could miss some interrupts.
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220630100241.35233-5-samuel@sholland.org
The Renesas RZ/Five SoC has a RISC-V AX45MP AndesCore with NCEPLIC100. The
NCEPLIC100 supports both edge-triggered and level-triggered interrupts. In
case of edge-triggered interrupts NCEPLIC100 ignores the next interrupt
edge until the previous completion message has been received and
NCEPLIC100 doesn't support pending interrupt counter, hence losing the
interrupts if not acknowledged in time.
So the workaround for edge-triggered interrupts to be handled correctly
and without losing is that it needs to be acknowledged first and then
handler must be run so that we don't miss on the next edge-triggered
interrupt.
This patch adds a new compatible string for NCEPLIC100 (from Andes
Technology) interrupt controller found on Renesas RZ/Five SoC and adds
quirk bits to priv structure and implements PLIC_QUIRK_EDGE_INTERRUPT
quirk to change the interrupt flow.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220630100241.35233-3-samuel@sholland.org
The sparse tool complains as follows:
drivers/irqchip/irq-apple-aic.c:231:1: warning:
symbol 'use_fast_ipi' was not declared. Should it be static?
This symbol is not used outside of irq-apple-aic.c, so marks it static.
Fixes: 2cf6821166 ("irqchip/apple-aic: Add Fast IPI support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220618072824.562350-1-weiyongjun1@huawei.com
Commit b84dc7f0e3 ("irqchip/xilinx: Remove microblaze+zynq
dependency") relaxed the dependencies on the Xilinx interrupt controller
to be OF only, but some OF architectures (s390 for example) do not
support OF_ADDRESS and so a build of the driver will result in undefined
references to of_iomap/iounmap and friends.
Fixes: b84dc7f0e3 ("irqchip/xilinx: Remove microblaze+zynq dependency")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220630111008.3838307-1-jamie@jamieiles.com
The mask_ack operation clears the interrupt by writing to the PICSR
register. This we don't want for level triggered interrupt because
it does not actually clear the interrupt on the source hardware.
This was causing issues in qemu with multi core setups where
interrupts would continue to fire even though they had been cleared in
PICSR.
Just remove the mask_ack operation.
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Due to a silly oversight on my part, making the simple switch to
of_io_request_and_map() in the DT path inadvertently introduced
divergent behaviour, whereby failng to request an iomem region now
becomes fatal for DT, vs. being silently ignored for ACPI.
Refactor a bit harder, so that request errors are non-fatal in both
paths as intended, but also consistently reported as well.
Reported-by: Matt Ranostay <mranostay@ti.com>
Fixes: 2b2cd74a06 ("irqchip/gic-v3: Claim iomem resources")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/5f2b57a0131f3082fae9d3002d360bf784ccb092.1655387206.git.robin.murphy@arm.com
Fix -Woverflow warnings for tegra irqchip driver which is a result
of moving arm64 custom MMIO accessor macros to asm-generic function
implementations giving a bonus type-checking now and uncovering these
overflow warnings.
drivers/irqchip/irq-tegra.c: In function ‘tegra_ictlr_suspend’:
drivers/irqchip/irq-tegra.c:151:18: warning: large integer implicitly truncated to unsigned type [-Woverflow]
writel_relaxed(~0ul, ictlr + ICTLR_COP_IER_CLR);
^
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fa84f89395 ("irqchip/loongson-liointc: Fix build error for
LoongArch") replaced get_ebase_cpunum with physical processor
id from SMP facilities. However that breaks MIPS non-SMP build
and makes booting from other cores inpossible on non-SMP kernel.
Thus we revert get_ebase_cpunum back and use get_csr_cpuid for
LoongArch.
Fixes: fa84f89395 ("irqchip/loongson-liointc: Fix build error for LoongArch")
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220609175242.977-1-jiaxun.yang@flygoat.com
of_find_node_by_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
This function doesn't call of_node_put() in error path.
Call of_node_put() directly after of_property_read_u32() to cover
both normal path and error path.
Fixes: 9f3a0f34b8 ("irqchip: Add support for Realtek RTL838x/RTL839x interrupt controller")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220601080930.31005-7-linmq006@gmail.com
of_find_node_by_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: e3825ba1af ("irqchip/gic-v3: Add support for partitioned PPIs")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220601080930.31005-6-linmq006@gmail.com
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
When kcalloc fails, it missing of_node_put() and results in refcount
leak. Fix this by goto out_put_node label.
Fixes: 52085d3f20 ("irqchip/gic-v3: Dynamically allocate PPI partition descriptors")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220601080930.31005-5-linmq006@gmail.com
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: a5e8801202 ("irqchip/apple-aic: Parse FIQ affinities from device-tree")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220601080930.31005-4-linmq006@gmail.com
of_find_node_by_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: a5e8801202 ("irqchip/apple-aic: Parse FIQ affinities from device-tree")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220601080930.31005-3-linmq006@gmail.com
of_find_matching_node_and_match() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 82b0a434b4 ("irqchip/gic/realview: Support more RealView DCC variants")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220601080930.31005-2-linmq006@gmail.com
The Xilinx IRQ controller doesn't really have any architecture
dependencies - it's a generic AXI component that can be used for any
FPGA core from Zynq hard processor systems to microblaze+riscv soft
cores and more.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220606213952.298686-1-jamie@jamieiles.com
liointc driver is shared by MIPS and LoongArch, this patch adjust the
code to fix build error for LoongArch.
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: WANG Xuerui <git@xen0n.name>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
HTVEC will be shared by both MIPS-based and LoongArch-based Loongson
processors (not only Loongson-3), so we adjust its description. HTPIC is
only used by MIPS-based Loongson, so we add a MIPS dependency.
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: WANG Xuerui <git@xen0n.name>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
- use ioread()/iowrite() interfaces instead of raw inb()/outb() in drivers
- make irqchips immutable due to the new warning popping up when drivers try to
modify the irqchip structures
- add new compatibles to dt-bindings for realtek-otto, renesas-rcar and pca95xx
- add support for new models to gpio-rcar, gpio-pca953x & gpio-realtek-otto
- allow parsing of GPIO hogs represented as children nodes of gpio-uniphier
- define a set of common GPIO consumer strings in dt-bindings
- shrink code in gpio-ml-ioh by using more devres interfaces
- pass arguments to devm_kcalloc() in correct order in gpio-sim
- add new helpers for iterating over GPIO firmware nodes and descriptors to
gpiolib core and use it in several drivers
- drop unused syscon_regmap_lookup_by_compatible() function
- correct format specifiers and signedness of variables in GPIO ACPI
- drop unneeded error checks in gpio-ftgpio
- stop using the deprecated of_gpio.h header in gpio-zevio
- drop platform_data support in gpio-max732x
- simplify Kconfig dependencies in gpio-vf610
- use raw spinlocks where needed to make PREEMPT_RT happy
- fix return values in board files using gpio-pcf857x
- convert more drivers to using fwnode instead of of_node
- minor fixes and improvements in gpiolib core
-----BEGIN PGP SIGNATURE-----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=tj/B
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have lots of small changes all over the place, but no huge reworks
or new drivers:
- use ioread()/iowrite() interfaces instead of raw inb()/outb() in
drivers
- make irqchips immutable due to the new warning popping up when
drivers try to modify the irqchip structures
- add new compatibles to dt-bindings for realtek-otto, renesas-rcar
and pca95xx
- add support for new models to gpio-rcar, gpio-pca953x &
gpio-realtek-otto
- allow parsing of GPIO hogs represented as children nodes of
gpio-uniphier
- define a set of common GPIO consumer strings in dt-bindings
- shrink code in gpio-ml-ioh by using more devres interfaces
- pass arguments to devm_kcalloc() in correct order in gpio-sim
- add new helpers for iterating over GPIO firmware nodes and
descriptors to gpiolib core and use it in several drivers
- drop unused syscon_regmap_lookup_by_compatible() function
- correct format specifiers and signedness of variables in GPIO ACPI
- drop unneeded error checks in gpio-ftgpio
- stop using the deprecated of_gpio.h header in gpio-zevio
- drop platform_data support in gpio-max732x
- simplify Kconfig dependencies in gpio-vf610
- use raw spinlocks where needed to make PREEMPT_RT happy
- fix return values in board files using gpio-pcf857x
- convert more drivers to using fwnode instead of of_node
- minor fixes and improvements in gpiolib core"
* tag 'gpio-updates-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (55 commits)
gpio: sifive: Make the irqchip immutable
gpio: rcar: Make the irqchip immutable
gpio: pcf857x: Make the irqchip immutable
gpio: pca953x: Make the irqchip immutable
gpio: dwapb: Make the irqchip immutable
gpio: sim: Use correct order for the parameters of devm_kcalloc()
gpio: ml-ioh: Convert to use managed functions pcim* and devm_*
gpio: ftgpio: Remove unneeded ERROR check before clk_disable_unprepare
gpio: ws16c48: Utilize iomap interface
gpio: gpio-mm: Utilize iomap interface
gpio: 104-idio-16: Utilize iomap interface
gpio: 104-idi-48: Utilize iomap interface
gpio: 104-dio-48e: Utilize iomap interface
gpio: zevio: drop of_gpio.h header
gpio: max77620: Make the irqchip immutable
dt-bindings: gpio: pca95xx: add entry for pca6408
gpio: pca953xx: Add support for pca6408
gpio: max732x: Drop unused support for irq and setup code via platform data
gpio: vf610: drop the SOC_VF610 dependency for GPIO_VF610
gpio: syscon: Remove usage of syscon_regmap_lookup_by_compatible
...
The asm-generic tree contains three separate changes for linux-5.19:
- The h8300 architecture is retired after it has been effectively
unmaintained for a number of years. This is the last architecture we
supported that has no MMU implementation, but there are still a few
architectures (arm, m68k, riscv, sh and xtensa) that support CPUs with
and without an MMU.
- A series to add a generic ticket spinlock that can be shared by most
architectures with a working cmpxchg or ll/sc type atomic, including
the conversion of riscv, csky and openrisc. This series is also a
prerequisite for the loongarch64 architecture port that will come as
a separate pull request.
- A cleanup of some exported uapi header files to ensure they can be
included from user space without relying on other kernel headers.
-----BEGIN PGP SIGNATURE-----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=ri2Q
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"The asm-generic tree contains three separate changes for linux-5.19:
- The h8300 architecture is retired after it has been effectively
unmaintained for a number of years. This is the last architecture
we supported that has no MMU implementation, but there are still a
few architectures (arm, m68k, riscv, sh and xtensa) that support
CPUs with and without an MMU.
- A series to add a generic ticket spinlock that can be shared by
most architectures with a working cmpxchg or ll/sc type atomic,
including the conversion of riscv, csky and openrisc. This series
is also a prerequisite for the loongarch64 architecture port that
will come as a separate pull request.
- A cleanup of some exported uapi header files to ensure they can be
included from user space without relying on other kernel headers"
* tag 'asm-generic-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
h8300: remove stale bindings and symlink
sparc: add asm/stat.h to UAPI compile-test coverage
powerpc: add asm/stat.h to UAPI compile-test coverage
mips: add asm/stat.h to UAPI compile-test coverage
riscv: add linux/bpf_perf_event.h to UAPI compile-test coverage
kbuild: prevent exported headers from including <stdlib.h>, <stdbool.h>
agpgart.h: do not include <stdlib.h> from exported header
csky: Move to generic ticket-spinlock
RISC-V: Move to queued RW locks
RISC-V: Move to generic spinlocks
openrisc: Move to ticket-spinlock
asm-generic: qrwlock: Document the spinlock fairness requirements
asm-generic: qspinlock: Indicate the use of mixed-size atomics
asm-generic: ticket-lock: New generic ticket-based spinlock
remove the h8300 architecture
- Add new infrastructure to stop gpiolib from rewriting irq_chip
structures behind our back. Convert a few of them, but this will
obviously be a long effort.
- A bunch of GICv3 improvements, such as using MMIO-based invalidations
when possible, and reducing the amount of polling we perform when
reconfiguring interrupts.
- Another set of GICv3 improvements for the Pseudo-NMI functionality,
with a nice cleanup making it easy to reason about the various
states we can be in when an NMI fires.
- The usual bunch of misc fixes and minor improvements.
-----BEGIN PGP SIGNATURE-----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=nQxd
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- Add new infrastructure to stop gpiolib from rewriting irq_chip
structures behind our back. Convert a few of them, but this will
obviously be a long effort.
- A bunch of GICv3 improvements, such as using MMIO-based invalidations
when possible, and reducing the amount of polling we perform when
reconfiguring interrupts.
- Another set of GICv3 improvements for the Pseudo-NMI functionality,
with a nice cleanup making it easy to reason about the various
states we can be in when an NMI fires.
- The usual bunch of misc fixes and minor improvements.
Link: https://lore.kernel.org/all/20220519165308.998315-1-maz@kernel.org
* irq/gic-v3-nmi-fixes-5.19:
: .
: GICv3 pseudo-NMI fixes from Mark Rutland:
:
: "These patches fix a couple of issues with the way GICv3 pseudo-NMIs are
: handled:
:
: * The first patch adds a barrier we missed from NMI handling due to an
: oversight.
:
: * The second patch refactors some logic around reads from ICC_IAR1_EL1
: and adds commentary to explain what's going on.
:
: * The third patch descends into madness, reworking gic_handle_irq() to
: consistently manage ICC_PMR_EL1 + DAIF and avoid cases where these can
: be left in an inconsistent state while softirqs are processed."
: .
irqchip/gic-v3: Fix priority mask handling
irqchip/gic-v3: Refactor ISB + EOIR at ack time
irqchip/gic-v3: Ensure pseudo-NMIs have an ISB between ack and handling
Signed-off-by: Marc Zyngier <maz@kernel.org>
Not all of these drivers are needed on every ARCH_SUNXI platform. In
particular, the ARCH_SUNXI symbol will be reused for the Allwinner D1,
a RISC-V SoC which contains none of these irqchips.
Introduce Kconfig symbols so we can select only the drivers actually
used by a particular set of platforms. This also lets us move the
irqchip driver dependencies to a more appropriate location.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220509034941.30704-1-samuel@sholland.org
When a kernel is built with CONFIG_ARM64_PSEUDO_NMI=y and pseudo-NMIs
are enabled at runtime, GICv3's gic_handle_irq() can leave DAIF and
ICC_PMR_EL1 in an unexpected state in some cases, breaking subsequent
usage of local_irq_enable() and resulting in softirqs being run with
IRQs erroneously masked (possibly resulting in deadlocks).
This can happen when an IRQ exception is taken from a context where
regular IRQs were unmasked, and either:
(1) ICC_IAR1_EL1 indicates a special INTID (e.g. as a result of an IRQ
being withdrawn since the IRQ exception was taken).
(2) ICC_IAR1_EL1 and ICC_RPR_EL1 indicate an NMI was acknowledged.
When an NMI is taken from a context where regular IRQs were masked,
there is no problem.
When CONFIG_ARM64_DEBUG_PRIORITY_MASKING=y, this can be detected with
perf, e.g.
| # ./perf record -a -g -e cycles:k ls -alR / > /dev/null 2>&1
| ------------[ cut here ]------------
| WARNING: CPU: 0 PID: 14 at arch/arm64/include/asm/irqflags.h:32 arch_local_irq_enable+0x4c/0x6c
| Modules linked in:
| CPU: 0 PID: 14 Comm: ksoftirqd/0 Not tainted 5.18.0-rc5-00004-g876c38e3d20b #12
| Hardware name: linux,dummy-virt (DT)
| pstate: 204000c5 (nzCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
| pc : arch_local_irq_enable+0x4c/0x6c
| lr : __do_softirq+0x110/0x5d8
| sp : ffff8000080bbbc0
| pmr_save: 000000f0
| x29: ffff8000080bbbc0 x28: ffff316ac3a6ca40 x27: 0000000000000000
| x26: 0000000000000000 x25: ffffa04611c06008 x24: ffffa04611c06008
| x23: 0000000040400005 x22: 0000000000000200 x21: ffff8000080bbe20
| x20: ffffa0460fe10320 x19: 0000000000000009 x18: 0000000000000000
| x17: ffff91252dfa9000 x16: ffff800008004000 x15: 0000000000004000
| x14: 0000000000000028 x13: ffffa0460fe17578 x12: ffffa0460fed4294
| x11: ffffa0460fedc168 x10: ffffffffffffff80 x9 : ffffa0460fe10a70
| x8 : ffffa0460fedc168 x7 : 000000000000b762 x6 : 00000000057c3bdf
| x5 : ffff8000080bbb18 x4 : 0000000000000000 x3 : 0000000000000001
| x2 : ffff91252dfa9000 x1 : 0000000000000060 x0 : 00000000000000f0
| Call trace:
| arch_local_irq_enable+0x4c/0x6c
| __irq_exit_rcu+0x180/0x1ac
| irq_exit_rcu+0x1c/0x44
| el1_interrupt+0x4c/0xe4
| el1h_64_irq_handler+0x18/0x24
| el1h_64_irq+0x74/0x78
| smpboot_thread_fn+0x68/0x2c0
| kthread+0x124/0x130
| ret_from_fork+0x10/0x20
| irq event stamp: 193241
| hardirqs last enabled at (193240): [<ffffa0460fe10a9c>] __do_softirq+0x10c/0x5d8
| hardirqs last disabled at (193241): [<ffffa0461102ffe4>] el1_dbg+0x24/0x90
| softirqs last enabled at (193234): [<ffffa0460fe10e00>] __do_softirq+0x470/0x5d8
| softirqs last disabled at (193239): [<ffffa0460fea9944>] __irq_exit_rcu+0x180/0x1ac
| ---[ end trace 0000000000000000 ]---
The necessary manipulation of DAIF and ICC_PMR_EL1 depends on the
interrupted context, but the structure of gic_handle_irq() makes this
also depend on whether the GIC reports an IRQ, NMI, or special INTID:
* When the interrupted context had regular IRQs masked (and hence the
interrupt must be an NMI), the entry code performs the NMI
entry/exit and gic_handle_irq() should return with DAIF and
ICC_PMR_EL1 unchanged.
This is handled correctly today.
* When the interrupted context had regular IRQs unmasked, the entry code
performs IRQ entry/exit, but expects gic_handle_irq() to always update
ICC_PMR_EL1 and DAIF.IF to unmask NMIs (but not regular IRQs) prior to
returning (which it must do prior to invoking any regular IRQ
handler).
This unbalanced calling convention is necessary because we don't know
whether an NMI has been taken until acknowledged by a read from
ICC_IAR1_EL1, and so we need to perform the read with NMI masked in
case an NMI has been taken (and needs to be handled with NMIs masked).
Unfortunately, this is not handled consistently:
- When ICC_IAR1_EL1 reports a special INTID, gic_handle_irq() returns
immediately without manipulating ICC_PMR_EL1 and DAIF.
- When RPR_EL1 indicates an NMI, gic_handle_irq() calls
gic_handle_nmi() to invoke the NMI handler, then returns without
manipulating ICC_PMR_EL1 and DAIF.
- For regular IRQs, gic_handle_irq() manipulates ICC_PMR_EL1 and DAIF
prior to invoking the IRQ handler.
There were related problems with special INTID handling in the past,
where if an exception was taken from a context with regular IRQs masked
and ICC_IAR_EL1 reported a special INTID, gic_handle_irq() would
erroneously unmask NMIs in NMI context permitted an unexpected nested
NMI. That case specifically was fixed by commit:
a97709f563 ("irqchip/gic-v3: Do not enable irqs when handling spurious interrups")
... but unfortunately that commit added an inverse problem, where if an
exception was taken from a context with regular IRQs *unmasked* and
ICC_IAR_EL1 reported a special INTID, gic_handle_irq() would erroneously
fail to unmask NMIs (and consequently regular IRQs could not be
unmasked during softirq processing). Before and after that commit, if an
NMI was taken from a context with regular IRQs unmasked gic_handle_irq()
would not unmask NMIs prior to returning, leading to the same problem
with softirq handling.
This patch fixes this by restructuring gic_handle_irq(), splitting it
into separate irqson/irqsoff helper functions which consistently perform
the DAIF + ICC_PMR1_EL1 manipulation based upon the interrupted context,
regardless of the event indicated by ICC_IAR1_EL1.
The special INTID handling is moved into the low-level IRQ/NMI handler
invocation helper functions, so that early returns don't prevent the
required manipulation of DAIF + ICC_PMR_EL1.
Fixes: f32c926651 ("irqchip/gic-v3: Handle pseudo-NMIs")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220513133038.226182-4-mark.rutland@arm.com
There are cases where a context synchronization event is necessary
between an IRQ being raised and being handled, and there are races such
that we cannot rely upon the exception entry being subsequent to the
interrupt being raised. To fix this, we place an ISB between a read of
IAR and the subsequent invocation of an IRQ handler.
When EOI mode 1 is in use, we need to EOI an interrupt prior to invoking
its handler, and we have a write to EOIR for this. As this write to EOIR
requires an ISB, and this is provided by the gic_write_eoir() helper, we
omit the usual ISB in this case, with the logic being:
| if (static_branch_likely(&supports_deactivate_key))
| gic_write_eoir(irqnr);
| else
| isb();
This is somewhat opaque, and it would be a little clearer if there were
an unconditional ISB, with only the write to EOIR being conditional,
e.g.
| if (static_branch_likely(&supports_deactivate_key))
| write_gicreg(irqnr, ICC_EOIR1_EL1);
|
| isb();
This patch rewrites the code that way, with this logic factored into a
new helper function with comments explaining what the ISB is for, as
were originally laid out in commit:
39a06b67c2 ("irqchip/gic: Ensure we have an ISB between ack and ->handle_irq")
Note that since then, we removed the IAR polling in commit:
342677d70a ("irqchip/gic-v3: Remove acknowledge loop")
... which removed one of the two race conditions.
For consistency, other portions of the driver are made to manipulate
EOIR using write_gicreg() and explcit ISBs, and the gic_write_eoir()
helper function is removed.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220513133038.226182-3-mark.rutland@arm.com
There are cases where a context synchronization event is necessary
between an IRQ being raised and being handled, and there are races such
that we cannot rely upon the exception entry being subsequent to the
interrupt being raised.
We identified and fixes this for regular IRQs in commit:
39a06b67c2 ("irqchip/gic: Ensure we have an ISB between ack and ->handle_irq")
Unfortunately, we forgot to do the same for psuedo-NMIs when support for
those was added in commit:
f32c926651 ("irqchip/gic-v3: Handle pseudo-NMIs")
Which means that when pseudo-NMIs are used for PMU support, we'll hit
the same problem.
Apply the same fix as for regular IRQs. Note that when EOI mode 1 is in
use, the call to gic_write_eoir() will provide an ISB.
Fixes: f32c926651 ("irqchip/gic-v3: Handle pseudo-NMIs")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220513133038.226182-2-mark.rutland@arm.com
Register ARMADA_370_XP_INT_FABRIC_MASK_OFFS is Armada 370 and XP specific
and on new Armada platforms it has different meaning. It does not configure
Performance Counter Overflow interrupt masking. So do not touch this
register on non-A370/XP platforms (A375, A38x and A39x).
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 28da06dfd9 ("irqchip: armada-370-xp: Enable the PMU interrupts")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220425113706.29310-1-pali@kernel.org
Issue the warning for interrupt lines that have an incorrect interrupt
type and also print the hardware interrupt number to facilitate the
resolution of such problems.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220308201117.3870678-1-f.fainelli@gmail.com
There are now SoCs that integrate the irqsteer controller within
a separate power domain. In order to allow this domain to be
powered down when not needed, add runtime PM support to the driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220406163701.1277930-2-l.stach@pengutronix.de
With multiple devices attached via PCIe to an Armada 385 it is possible
to overwhelm a single CPU with MSI interrupts. Under certain scenarios
configuring the interrupts to be handled by more than one CPU would
prevent the system from being overwhelmed. However the
irqchip-aramada-370-xp driver is configured to only handle MSIs on the
boot CPU, and provides no affinity configuration.
This change adds support to the armada-370-xp driver to allow for
configuring the affinity of specific MSI irqs and to generate the
interrupts on secondary CPUs. This is done by enabling the private
doorbell for all online CPUs and configures all CPUs to unmask MSI
specific private doorbell bits. The CPU affinity selection of the
interrupt is handled by the target list of the software triggered
interrupt value, which is provided as the MSI message. The message has
the associated CPU bit set for the target CPU. For private doorbell
interrupts only one bit can be set otherwise all CPUs will receive the
interrupt, so the lowest CPU in the affinity mask is used. This means
that by default the first CPU will handle all the interrupts as was the
case before.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220422043532.146946-1-nathan@nathanrossi.com
sparse complains about using an integer as a NULL pointer.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220424173952.36591-1-samuel@sholland.org
When irq-xtensa-mx chip is used in non-SMP configuration its
irq_set_affinity callback is not called leaving IRQ affinity set empty.
As a result IRQ delivery does not work in that configuration.
Initialize IRQ affinity of the xtensa MX interrupt distributor to CPU 0
for all external IRQ lines.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220426161912.1113784-1-jcmvbkbc@gmail.com
Currently the EXIU uses the fasteoi interrupt flow that is configured by
it's parent (irq-gic-v3.c). With this flow the only chance to clear the
interrupt request happens during .irq_eoi() and (obviously) this happens
after the interrupt handler has run. EXIU requires edge triggered
interrupts to be acked prior to interrupt handling. Without this we
risk incorrect interrupt dismissal when a new interrupt is delivered
after the handler reads and acknowledges the peripheral but before the
irq_eoi() takes place.
Fix this by clearing the interrupt request from .irq_ack() if we are
configured for edge triggered interrupts. This requires adopting the
fasteoi-ack flow instead of the fasteoi to ensure the ack gets called.
These changes have been tested using the power button on a
Developerbox/SC2A11 combined with some hackery in gpio-keys so I can
play with the different trigger mode [and an mdelay(500) so I can
can check what happens on a double click in both modes].
Fixes: 706cffc1b9 ("irqchip/exiu: Add support for Socionext Synquacer EXIU controller")
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220503134541.2566457-1-daniel.thompson@linaro.org
As a simple quality-of-life tweak, claim our MMIO regions when mapping
them, such that the GIC shows up in /proc/iomem. No effort is spent on
trying to release them, since frankly if the GIC fails to probe then
it's never getting a second try anyway.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/c534c2a458a3bf94ccdae8abc6edc3d45a689c30.1649777295.git.robin.murphy@arm.com
Recent work on the KVM GIC emulation has revealed that the GICv3
driver is a bit RWP-happy, as it polls this bit for each and
every write MMIO access involving a single interrupt.
As it turns out, polling RWP is only required when:
- Disabling an SGI, PPI or SPI
- Disabling LPIs at the redistributor level
- Disabling groups
- Enabling ARE
- Dealing with DPG*
Simplify the driver by removing all the other instances of RWP
polling, and add the one that was missing when enabling the distributor
(as that's where we set ARE).
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220405183857.205960-4-maz@kernel.org
Since GICv4.1, an implementation can offer the same MMIO-based
implementation as DirectLPI, only with an ITS. Given that this
can be hugely beneficial for workloads that are very LPI masking
heavy (although these workloads are admitedly a bit odd).
Interestingly, this is independent of RVPEI, which only *implies*
the functionnality.
So let's detect whether the implementation has GICR_CTLR.IR set,
and propagate this as DirectLPI to the ITS driver.
While we're at it, repaint the GICv3 banner so that we advertise
the various capabilities at boot time to be slightly less invasive.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220405183857.205960-3-maz@kernel.org
The boardfiles for IXP4xx have been deleted. Delete all the
quirks and code dealing with that boot path and rely solely on
device tree boot.
Fix some missing static keywords that the kernel test robot
was complaining about while we're at it.
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
bcm6345_l1_of_init() calls cpumask_weight() to check if any bit of a given
cpumask is set.
This can be done more efficiently with cpumask_empty() because
cpumask_empty() stops traversing the cpumask as soon as it finds first set
bit, while cpumask_weight() counts all bits unconditionally.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220210224933.379149-21-yury.norov@gmail.com
Now that the core code has been fixed to always give us an affinity
that only includes online CPUs, directly use this affinity when
computing a target CPU.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20220405185040.206297-4-maz@kernel.org
At the moment the GIC IRQ domain translation routine happily converts
ACPI table GSI numbers below 16 to GIC SGIs (Software Generated
Interrupts aka IPIs). On the Devicetree side we explicitly forbid this
translation, actually the function will never return HWIRQs below 16 when
using a DT based domain translation.
We expect SGIs to be handled in the first part of the function, and any
further occurrence should be treated as a firmware bug, so add a check
and print to report this explicitly and avoid lengthy debug sessions.
Fixes: 64b499d8df ("irqchip/gic-v3: Configure SGIs as standard interrupts")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220404110842.2882446-1-andre.przywara@arm.com
It turns out that our polling of RWP is totally wrong when checking
for it in the redistributors, as we test the *distributor* bit index,
whereas it is a different bit number in the RDs... Oopsie boo.
This is embarassing. Not only because it is wrong, but also because
it took *8 years* to notice the blunder...
Just fix the damn thing.
Fixes: 021f653791 ("irqchip: gic-v3: Initial support for GICv3")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20220315165034.794482-2-maz@kernel.org
The way KVM drives GICv4.{0,1} is as follows:
- vcpu_load() makes the VPE resident, instructing the RD to start
scanning for interrupts
- just before entering the guest, we check that the RD has finished
scanning and that we can start running the vcpu
- on preemption, we deschedule the VPE by making it invalid on
the RD
However, we are preemptible between the first two steps. If it so
happens *and* that the RD was still scanning, we nonetheless write
to the GICR_VPENDBASER register while Dirty is set, and bad things
happen (we're in UNPRED land).
This affects both the 4.0 and 4.1 implementations.
Make sure Dirty is cleared before performing the deschedule,
meaning that its_clear_vpend_valid() becomes a sort of full VPE
residency barrier.
Reported-by: Jingyi Wang <wangjingyi11@huawei.com>
Tested-by: Nianyao Tang <tangnianyao@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fixes: 57e3cebd02 ("KVM: arm64: Delay the polling of the GICR_VPENDBASER.Dirty bit")
Link: https://lore.kernel.org/r/4aae10ba-b39a-5f84-754b-69c2eb0a2c03@huawei.com
If MAILBOX is n, building fails:
drivers/irqchip/irq-qcom-mpm.o: In function `mpm_pd_power_off':
irq-qcom-mpm.c:(.text+0x174): undefined reference to `mbox_send_message'
irq-qcom-mpm.c:(.text+0x174): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `mbox_send_message'
Make QCOM_MPM depends on MAILBOX to fix this.
Fixes: a6199bb514 ("irqchip: Add Qualcomm MPM controller driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220317131956.30004-1-yuehaibing@huawei.com
* 'remove-h8300' of git://git.infradead.org/users/hch/misc:
remove the h8300 architecture
This is clearly the least actively maintained architecture we have at
the moment, and probably the least useful. It is now the only one that
does not support MMUs at all, and most of the boards only support 4MB
of RAM, out of which the defconfig kernel needs more than half just
for .text/.data.
Guenter Roeck did the original patch to remove the architecture in 2013
after it had already been obsolete for a while, and Yoshinori Sato brought
it back in a much more modern form in 2015. Looking at the git history
since the reinstantiation, it's clear that almost all commits in the tree
are build fixes or cross-architecture cleanups:
$ git log --no-merges --format=%an v4.5.. arch/h8300/ | sort | uniq
-c | sort -rn | head -n 12
25 Masahiro Yamada
18 Christoph Hellwig
14 Mike Rapoport
9 Arnd Bergmann
8 Mark Rutland
7 Peter Zijlstra
6 Kees Cook
6 Ingo Molnar
6 Al Viro
5 Randy Dunlap
4 Yury Norov
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are three sets of updates for 5.18 in the asm-generic tree:
- The set_fs()/get_fs() infrastructure gets removed for good. This
was already gone from all major architectures, but now we can
finally remove it everywhere, which loses some particularly
tricky and error-prone code.
There is a small merge conflict against a parisc cleanup, the
solution is to use their new version.
- The nds32 architecture ends its tenure in the Linux kernel. The
hardware is still used and the code is in reasonable shape, but
the mainline port is not actively maintained any more, as all
remaining users are thought to run vendor kernels that would never
be updated to a future release.
There are some obvious conflicts against changes to the removed
files.
- A series from Masahiro Yamada cleans up some of the uapi header
files to pass the compile-time checks.
-----BEGIN PGP SIGNATURE-----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=vtCN
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are three sets of updates for 5.18 in the asm-generic tree:
- The set_fs()/get_fs() infrastructure gets removed for good.
This was already gone from all major architectures, but now we can
finally remove it everywhere, which loses some particularly tricky
and error-prone code. There is a small merge conflict against a
parisc cleanup, the solution is to use their new version.
- The nds32 architecture ends its tenure in the Linux kernel.
The hardware is still used and the code is in reasonable shape, but
the mainline port is not actively maintained any more, as all
remaining users are thought to run vendor kernels that would never
be updated to a future release.
- A series from Masahiro Yamada cleans up some of the uapi header
files to pass the compile-time checks"
* tag 'asm-generic-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (27 commits)
nds32: Remove the architecture
uaccess: remove CONFIG_SET_FS
ia64: remove CONFIG_SET_FS support
sh: remove CONFIG_SET_FS support
sparc64: remove CONFIG_SET_FS support
lib/test_lockup: fix kernel pointer check for separate address spaces
uaccess: generalize access_ok()
uaccess: fix type mismatch warnings from access_ok()
arm64: simplify access_ok()
m68k: fix access_ok for coldfire
MIPS: use simpler access_ok()
MIPS: Handle address errors for accesses above CPU max virtual user address
uaccess: add generic __{get,put}_kernel_nofault
nios2: drop access_ok() check from __put_user()
x86: use more conventional access_ok() definition
x86: remove __range_not_ok()
sparc64: add __{get,put}_kernel_nofault()
nds32: fix access_ok() checks in get/put_user
uaccess: fix nios2 and microblaze get_user_8()
sparc64: fix building assembly files
...
Updates for IRQ stacks and virtually mapped stack support for ARM from
the following pull requests, etc:
1) ARM: support for IRQ and vmap'ed stacks
This PR covers all the work related to implementing IRQ stacks and
vmap'ed stacks for all 32-bit ARM systems that are currently supported
by the Linux kernel, including RiscPC and Footbridge. It has been
submitted for review in three different waves:
- IRQ stacks support for v7 SMP systems [0],
- vmap'ed stacks support for v7 SMP systems[1],
- extending support for both IRQ stacks and vmap'ed stacks for all
remaining configurations, including v6/v7 SMP multiplatform kernels
and uniprocessor configurations including v7-M [2]
[0] https://lore.kernel.org/linux-arm-kernel/20211115084732.3704393-1-ardb@kernel.org/
[1] https://lore.kernel.org/linux-arm-kernel/20211122092816.2865873-1-ardb@kernel.org/
[2] https://lore.kernel.org/linux-arm-kernel/20211206164659.1495084-1-ardb@kernel.org/
2) ARM: support for IRQ and vmap'ed stacks [v6]
This tag covers the changes between the version of vmap'ed + IRQ stacks
support pulled into rmk/devel-stable [0] (which was dropped from v5.17
due to issues discovered too late in the cycle), and my v5 proposed for
the v5.18 cycle [1].
[0] git://git.kernel.org/pub/scm/linux/kernel/git/ardb/linux.git arm-irq-and-vmap-stacks-for-rmk
[1] https://lore.kernel.org/linux-arm-kernel/20220124174744.1054712-1-ardb@kernel.org/
3) ARM: ftrace fixes and cleanups
Make all flavors of ftrace available on all builds, regardless of ISA
choice, unwinder choice or compiler:
- use ADD not POP where possible
- fix a couple of Thumb2 related issues
- enable HAVE_FUNCTION_GRAPH_FP_TEST for robustness
- enable the graph tracer with the EABI unwinder
- avoid clobbering frame pointer registers to make Clang happy
Link: https://lore.kernel.org/linux-arm-kernel/20220203082204.1176734-1-ardb@kernel.org/
4) Fixes for the above.
-----BEGIN PGP SIGNATURE-----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=AVCL
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
"Updates for IRQ stacks and virtually mapped stack support, and ftrace:
- Support for IRQ and vmap'ed stacks
This covers all the work related to implementing IRQ stacks and
vmap'ed stacks for all 32-bit ARM systems that are currently
supported by the Linux kernel, including RiscPC and Footbridge. It
has been submitted for review in four different waves:
- IRQ stacks support for v7 SMP systems [0]
- vmap'ed stacks support for v7 SMP systems[1]
- extending support for both IRQ stacks and vmap'ed stacks for all
remaining configurations, including v6/v7 SMP multiplatform
kernels and uniprocessor configurations including v7-M [2]
- fixes and updates in [3]
- ftrace fixes and cleanups
Make all flavors of ftrace available on all builds, regardless of
ISA choice, unwinder choice or compiler [4]:
- use ADD not POP where possible
- fix a couple of Thumb2 related issues
- enable HAVE_FUNCTION_GRAPH_FP_TEST for robustness
- enable the graph tracer with the EABI unwinder
- avoid clobbering frame pointer registers to make Clang happy
- Fixes for the above"
[0] https://lore.kernel.org/linux-arm-kernel/20211115084732.3704393-1-ardb@kernel.org/
[1] https://lore.kernel.org/linux-arm-kernel/20211122092816.2865873-1-ardb@kernel.org/
[2] https://lore.kernel.org/linux-arm-kernel/20211206164659.1495084-1-ardb@kernel.org/
[3] https://lore.kernel.org/linux-arm-kernel/20220124174744.1054712-1-ardb@kernel.org/
[4] https://lore.kernel.org/linux-arm-kernel/20220203082204.1176734-1-ardb@kernel.org/
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (62 commits)
ARM: fix building NOMMU ARMv4/v5 kernels
ARM: unwind: only permit stack switch when unwinding call_with_stack()
ARM: Revert "unwind: dump exception stack from calling frame"
ARM: entry: fix unwinder problems caused by IRQ stacks
ARM: unwind: set frame.pc correctly for current-thread unwinding
ARM: 9184/1: return_address: disable again for CONFIG_ARM_UNWIND=y
ARM: 9183/1: unwind: avoid spurious warnings on bogus code addresses
Revert "ARM: 9144/1: forbid ftrace with clang and thumb2_kernel"
ARM: mach-bcm: disable ftrace in SMC invocation routines
ARM: cacheflush: avoid clobbering the frame pointer
ARM: kprobes: treat R7 as the frame pointer register in Thumb2 builds
ARM: ftrace: enable the graph tracer with the EABI unwinder
ARM: unwind: track location of LR value in stack frame
ARM: ftrace: enable HAVE_FUNCTION_GRAPH_FP_TEST
ARM: ftrace: avoid unnecessary literal loads
ARM: ftrace: avoid redundant loads or clobbering IP
ARM: ftrace: use trampolines to keep .init.text in branching range
ARM: ftrace: use ADD not POP to counter PUSH at entry
ARM: ftrace: ensure that ADR takes the Thumb bit into account
ARM: make get_current() and __my_cpu_offset() __always_inline
...
- Add support for the STM32MP13 variant
- Move parent device away from struct irq_chip
- Remove all instances of non-const strings assigned to
struct irq_chip::name, enabling a nice cleanup for VIC and GIC)
- Simplify the Qualcomm PDC driver
- A bunch of SiFive PLIC cleanups
- Add support for a new variant of the Meson GPIO block
- Add support for the irqchip side of the Apple M1 PMU
- Add support for the Apple M1 Pro/Max AICv2 irqchip
- Add support for the Qualcomm MPM wakeup gadget
- Move the Xilinx driver over to the generic irqdomain handling
- Tiny speedup for IPIs on GICv3 systems
- The usual odd cleanups
-----BEGIN PGP SIGNATURE-----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=cf1B
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- Add support for the STM32MP13 variant
- Move parent device away from struct irq_chip
- Remove all instances of non-const strings assigned to
struct irq_chip::name, enabling a nice cleanup for VIC and GIC)
- Simplify the Qualcomm PDC driver
- A bunch of SiFive PLIC cleanups
- Add support for a new variant of the Meson GPIO block
- Add support for the irqchip side of the Apple M1 PMU
- Add support for the Apple M1 Pro/Max AICv2 irqchip
- Add support for the Qualcomm MPM wakeup gadget
- Move the Xilinx driver over to the generic irqdomain handling
- Tiny speedup for IPIs on GICv3 systems
- The usual odd cleanups
Link: https://lore.kernel.org/all/20220313105142.704579-1-maz@kernel.org
The removal of the old-style irq entry broke obscure NOMMU
configurations on machines that have an MMU:
ld.lld: error: undefined symbol: generic_handle_arch_irq
referenced by kernel/entry-armv.o:(__irq_svc) in archive arch/arm/built-in.a
A follow-up patch to convert nvic to the generic_handle_arch_irq()
could have fixed this by removing the Kconfig conditional, but did
it differently.
Change the Kconfig logic so ARM machines now unconditionally
enable the feature.
I have also submitted a patch to remove support for the configurations
that broke, but fixing the regression first is a trivial and correct
change.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 54f481a230 ("ARM: remove old-style irq entry")
Fixes: 52d2408717 ("irqchip: nvic: Use GENERIC_IRQ_MULTI_HANDLER")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Qualcomm SoCs based on the RPM architecture have a MSM Power Manager (MPM)
in always-on domain. In addition to managing resources during sleep, the
hardware also has an interrupt controller that monitors the interrupts
when the system is asleep, wakes up the APSS when one of these interrupts
occur and replays it to GIC after it becomes operational.
It adds an irqchip driver for this interrupt controller, and here are
some notes about it.
- For given SoC, a fixed number of MPM pins are supported, e.g. 96 pins
on QCM2290. Each of these MPM pins can be either a MPM_GIC pin or
a MPM_GPIO pin. The mapping between MPM_GIC pin and GIC interrupt
is defined by SoC, as well as the mapping between MPM_GPIO pin and
GPIO number. The former mapping is retrieved from device tree, while
the latter is defined in TLMM pinctrl driver.
- The power domain (PD) .power_off hook is used to notify RPM that APSS
is about to power collapse. This requires MPM PD be the parent PD of
CPU cluster.
- When SoC gets awake from sleep mode, the driver will receive an
interrupt from RPM, so that it can replay interrupt for particular
polarity.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220308080534.3384532-3-shawn.guo@linaro.org
* irq/aic-v2:
: .
: Add support for the interrupt controller found is the latest
: incarnation of Apple M1 systems, courtesy of Hector Martin.
: .
irqchip/apple-aic: Add support for AICv2
irqchip/apple-aic: Support multiple dies
irqchip/apple-aic: Dynamically compute register offsets
irqchip/apple-aic: Switch to irq_domain_create_tree and sparse hwirqs
irqchip/apple-aic: Add Fast IPI support
dt-bindings: interrupt-controller: apple,aic2: New binding for AICv2
PCI: apple: Change MSI handling to handle 4-cell AIC fwspec form
Signed-off-by: Marc Zyngier <maz@kernel.org>
Introduce support for the new AICv2 hardware block in t6000/t6001 SoCs.
It seems these blocks are missing the information required to compute
the event register offset in the capability registers, so we specify
that in the DT as a second reg entry.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220309192123.152028-8-marcan@marcan.st
Multi-die support in AICv2 uses several sets of IRQ registers. Introduce
a die count and compute the register group offset based on the die ID
field of the hwirq number, as reported by the hardware.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220309192123.152028-7-marcan@marcan.st
This allows us to support AIC variants with different numbers of IRQs
based on capability registers.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220309192123.152028-6-marcan@marcan.st
This allows us to directly use the hardware event number as the hwirq
number. Since IRQ events have bit 16 set (type=1), FIQs now move to
starting at hwirq number 0.
This will become more important once multi-die support is introduced in
a later commit.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220309192123.152028-5-marcan@marcan.st
The newer AICv2 present in t600x SoCs does not have legacy IPI support
at all. Since t8103 also supports Fast IPIs, implement support for this
first. The legacy IPI code is left as a fallback, so it can be
potentially used by older SoCs in the future.
The vIPI code is shared; only the IPI firing/acking bits change for Fast
IPIs.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220309192123.152028-4-marcan@marcan.st
An emparassing typo: allocating a pointer instead of the object
pointed to. No harm done, as the pointer is large enough for
what we are using the object for, but still...
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220310050238.4478-1-guozhengkui@vivo.com
* irq/meson-gpio:
: .
: Expand meson-gpio support to deal with the new Meson-S4 SoC
: .
irqchip/meson-gpio: Add support for meson s4 SoCs
irqchip/meson-gpio: add select trigger type callback
irqchip/meson-gpio: support more than 8 channels gpio irq
dt-bindings: interrupt-controller: New binding for Meson-S4 SoCs
Signed-off-by: Marc Zyngier <maz@kernel.org>
The meson s4 SoCs support 12 gpio irq lines compared with previous
serial chips and have something different, details are as below.
IRQ Number:
- 80:68 13 pins on bank Z
- 67:48 20 pins on bank X
- 47:36 12 pins on bank H
- 35:24 12 pins on bank D
- 23:22 2 pins on bank E
- 21:14 8 pins on bank C
- 13:0 13 pins on bank B
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
[maz: fixed some W=1 build warnings]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220225055207.1048-5-qianggui.song@amlogic.com
The nds32 architecture, also known as AndeStar V3, is a custom 32-bit
RISC target designed by Andes Technologies. Support was added to the
kernel in 2016 as the replacement RISC-V based V5 processors were
already announced, and maintained by (current or former) Andes
employees.
As explained by Alan Kao, new customers are now all using RISC-V,
and all known nds32 users are already on longterm stable kernels
provided by Andes, with no development work going into mainline
support any more.
While the port is still in a reasonably good shape, it only gets
worse over time without active maintainers, so it seems best
to remove it before it becomes unusable. As always, if it turns
out that there are mainline users after all, and they volunteer
to maintain the port in the future, the removal can be reverted.
Link: https://lore.kernel.org/linux-mm/YhdWNLUhk+x9RAzU@yamatobi.andestech.com/
Link: https://lore.kernel.org/lkml/20220302065213.82702-1-alankao@andestech.com/
Link: https://www.andestech.com/en/products-solutions/andestar-architecture/
Signed-off-by: Alan Kao <alankao@andestech.com>
[arnd: rewrite changelog to provide more background]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Due to some chips may use different registers and offset, provide
a set trigger type call back and add one for old controller.
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220225055207.1048-4-qianggui.song@amlogic.com
Current meson gpio irqchip driver only support 8 channels for gpio irq
line, later chips may have more then 8 channels, so need to modify code
to support more.
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220225055207.1048-3-qianggui.song@amlogic.com
* irq/misc-5.18:
: .
: Misc irq chip changes for 5.18
:
: - GICv3: Relax ordering of previous stores to only include the ISH domain
:
: - nvic: Unmap MMIo region on probe failure
:
: - xilinx: Switch to GENERIC_IRQ_MULTI_HANDLER when used on microblaze
: .
irqchip/xilinx: Switch to GENERIC_IRQ_MULTI_HANDLER
irqchip/nvic: Release nvic_base upon failure
irqchip/gic-v3: Use dsb(ishst) to order writes with ICC_SGI1R_EL1 accesses
Signed-off-by: Marc Zyngier <maz@kernel.org>
* irq/plic-cleanups:
: .
: SiFive PLIC cleanups from Niklas Cassel:
:
: - Clarify some of the namings in the driver
:
: - Make sure S-mode interrupts are disabled when running in M-mode
: .
irqchip/sifive-plic: Disable S-mode IRQs if running in M-mode
irqchip/sifive-plic: Improve naming scheme for per context offsets
Signed-off-by: Marc Zyngier <maz@kernel.org>
Register the Xilinx driver as the root interrupt controller using
the GENERIC_IRQ_MULTI_HANDLER API, instead of the arch-specific hack.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Asserhall <stefan.asserhall@xilinx.com>
[maz: repainted commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/e6c6595a81f662bf839cee3109d0fa58a596ea47.1646380284.git.michal.simek@xilinx.com
When detecting a context for a privilege mode different from the current
running privilege mode, we simply skip to the next context register.
This means that we never clear the S-mode enable bits when running in
M-mode.
On canaan k210, a bunch of S-mode interrupts are enabled by the bootrom.
These S-mode specific interrupts should never trigger, since we never set
the mie.SEIE bit in the parent interrupt controller (riscv-intc).
However, we will be able to see the mip.SEIE bit set as pending.
This isn't a good default when CONFIG_RISCV_M_MODE is set, since in that
case we will never enter a lower privilege mode (e.g. S-mode).
Let's clear the S-mode enable bits when running the kernel in M-mode, such
that we won't have a interrupt pending bit set, which we will never clear.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220302131544.3166154-3-Niklas.Cassel@wdc.com
The PLIC supports a fixed number of contexts (15872).
Each context has fixed register offsets in PLIC.
The number of contexts that we need to initialize depends on the privilege
modes supported by each hart. Therefore, this mapping between PLIC context
registers to hart privilege modes is platform specific, and is currently
supplied via device tree.
For example, canaan,k210 has the following mapping:
Context0: hart0 M-mode
Context1: hart0 S-mode
Context2: hart1 M-mode
Context3: hart1 S-mode
While sifive,fu540 has the following mapping:
Context0: hart0 M-mode
Context1: hart1 M-mode
Context2: hart1 S-mode
Because the number of contexts per hart is not fixed, the names
ENABLE_PER_HART and CONTEXT_PER_HART for the register offsets are quite
confusing and might mislead the reader to think that these are fixed
register offsets per hart.
Rename the offsets to more clearly highlight that these are per PLIC
context and not per hart.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220302131544.3166154-2-Niklas.Cassel@wdc.com
* irq/qcom-pdc-cleanup:
: .
: Spring cleanup for the Qualcomm PDC driver, simplifying its
: use of irq domains, replacing open-coded functionnalities with
: the core code equivalent, and fixing the dodgy locking.
: .
irqchip/qcom-pdc: Drop open coded version of __assign_bit()
irqchip/qcom-pdc: Fix broken locking
irqchip/qcom-pdc: Kill qcom_pdc_translate helper
irqchip/qcom-pdc: Kill non-wakeup irqdomain
irqchip/qcom-pdc: Kill PDC_NO_PARENT_IRQ
Signed-off-by: Marc Zyngier <maz@kernel.org>
smatch warning was reported as below ->
smatch warnings:
drivers/irqchip/irq-nvic.c:131 nvic_of_init()
warn: 'nvic_base' not released on lines: 97.
Release nvic_base upon failure.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Souptick Joarder (HPE) <jrdr.linux@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220218163303.33344-1-jrdr.linux@gmail.com
The driver uses what looks like an open-coded version of __assign_bit().
Replace it with the real thing.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Maulik Shah <quic_mkshah@quicinc.com>
Link: https://lore.kernel.org/r/20220224101226.88373-6-maz@kernel.org
pdc_enable_intr() serves as a primitive to qcom_pdc_gic_{en,dis}able,
and has a raw spinlock for mutual exclusion, which is uses with
interruptible primitives.
This means that this critical section can itself be interrupted.
Should the interrupt also be a PDC interrupt, and the endpoint driver
perform an irq_disable() on that interrupt, we end-up in a deadlock.
Fix this by using the irqsave/irqrestore variants of the locking
primitives.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Maulik Shah <quic_mkshah@quicinc.com>
Link: https://lore.kernel.org/r/20220224101226.88373-5-maz@kernel.org
qcom_pdc_translate() really is nothing but an open coded version
of irq_domain_translate_twocell(). Get rid of it and use the common
version instead.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Maulik Shah <quic_mkshah@quicinc.com>
Link: https://lore.kernel.org/r/20220224101226.88373-4-maz@kernel.org
A careful look at the way the PDC driver works shows that:
- all interrupts are in the same space
- all interrupts are treated the same
And yet the driver creates two domains based on whether
the interrupt gets mapped directly or from the pinctrl code,
which is obviously a waste of resources.
Kill the non-wakeup domain and unify all the interrupt handling.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220224101226.88373-3-maz@kernel.org
PDC_NO_PARENT_IRQ is pretty pointless, as all it indicates is
that the PDC terminates the interrupt hierarchy. Which is
exactly the same as not having a mapping in the GIC space.
This is also bad practice to treat the absence of a hwirq
as a hwirq itself.
Just explicitly use the region mapping pointer, and drop
the definition.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Maulik Shah <quic_mkshah@quicinc.com>
Link: https://lore.kernel.org/r/20220224101226.88373-2-maz@kernel.org
A dsb(ishst) barrier should be enough to order previous writes with
the system register generating the SGI, as we only need to guarantee
the visibility of data to other CPUs in the inner shareable domain
before we send the SGI.
A micro-benchmark is written to verify the performance impact on
kunpeng920 machine with 2 sockets, each socket has 2 dies, and
each die has 24 CPUs, so totally the system has 2 * 2 * 24 = 96
CPUs. ~2% performance improvement can be seen by this benchmark.
The code of benchmark module:
#include <linux/module.h>
#include <linux/timekeeping.h>
volatile int data0 ____cacheline_aligned;
volatile int data1 ____cacheline_aligned;
volatile int data2 ____cacheline_aligned;
volatile int data3 ____cacheline_aligned;
volatile int data4 ____cacheline_aligned;
volatile int data5 ____cacheline_aligned;
volatile int data6 ____cacheline_aligned;
static void ipi_latency_func(void *val)
{
}
static int __init ipi_latency_init(void)
{
ktime_t stime, etime, delta;
int cpu, i;
int start = smp_processor_id();
stime = ktime_get();
for ( i = 0; i < 1000; i++)
for (cpu = 0; cpu < 96; cpu++) {
data0 = data1 = data2 = data3 = data4 = data5 = data6 = cpu;
smp_call_function_single(cpu, ipi_latency_func, NULL, 1);
}
etime = ktime_get();
delta = ktime_sub(etime, stime);
printk("%s ipi from cpu%d to cpu0-95 delta of 1000times:%lld\n",
__func__, start, delta);
return 0;
}
module_init(ipi_latency_init);
static void ipi_latency_exit(void)
{
}
module_exit(ipi_latency_exit);
MODULE_DESCRIPTION("IPI benchmark");
MODULE_LICENSE("GPL");
run the below commands 10 times on both Vanilla and the kernel with this
patch:
# taskset -c 0 insmod test.ko
# rmmod test
The result on vanilla:
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:126757449
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:126784249
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:126177703
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:127022281
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:126184883
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:127374585
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:125778089
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:126974441
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:127357625
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:126228184
The result on the kernel with this patch:
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:124467401
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:123474209
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:123558497
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:122993951
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:122984223
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:123323609
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:124507583
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:123386963
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:123340664
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:123285324
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
[maz: tidied up commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220220061910.6155-1-21cnbao@gmail.com
* irq/print_chip:
: .
: Convert irqchip drivers that use the .name field as a topology
: description to the .irq_print_chip callback, which allows the
: name to be made dymanic. The irq_chip structures are then made
: 'const' in order to prevent further abuse.
: .
irqchip/versatile-fpga: Switch to dynamic chip name output
irqchip/ts4800: Switch to dynamic chip name output
irqchip/mvebu-pic: Switch to dynamic chip name output
irqchip/lpc32xx: Switch to dynamic chip name output
irqchip/gic: Switch to dynamic chip name output
genirq/debugfs: Use irq_print_chip() when provided by irqchip
genirq: Allow irq_chip registration functions to take a const irq_chip
irqdomain: Let irq_domain_set_{info,hwirq_and_chip} take a const irq_chip
Signed-off-by: Marc Zyngier <maz@kernel.org>
Move the name output to the relevant callback, which allows us
some nice cleanups (mostly owing to the fact that the driver is
now DT only.
We also drop a random include directive from the ftintc010 driver.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220209162607.1118325-8-maz@kernel.org
Instead of overriding the name field, track the corresponding device
and use the relevant callback to output its name.
This allows us to make the irq_chip structure const.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220209162607.1118325-6-maz@kernel.org
Instead of overriding the name field with the device name, use
the relevant callback. This allows us to make the irq_chip structure
const.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220209162607.1118325-5-maz@kernel.org
The last dynamic aspect of the GIC's irq_chip structure is the
name that is associated to it.
Move the output of that name to the relevant callback, which
allows us to do a bit of cleanup and mark the structures const.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220209162607.1118325-4-maz@kernel.org
* irq/parent_device:
: .
: Move irq_chip::parent_device to irq_domain::dev to track the
: PM state of the device implementing the irqchip.
: .
genirq: Kill irq_chip::parent_device
pinctrl: starfive: Move PM device over to irq domain
pinctrl: npcm: Fix broken references to chip->parent_device
gpio: tpmx86: Move PM device over to irq domain
gpio: rcar: Move PM device over to irq domain
gpio: omap: Move PM device over to irq domain
gpio: mt7621: Kill parent_device usage
irqchip/imx-intmux: Move PM device over to irq domain
irqchip/renesas-irqc: Move PM device over to irq domain
irqchip/renesas-intc-irqpin: Move PM device over to irq domain
irqchip/gic: Move PM device over to irq domain
genirq: Allow the PM device to originate from irq domain
Signed-off-by: Marc Zyngier <maz@kernel.org>
Enhance stm32-exti driver to support STM32MP13 SoC. This SoC uses the same
hardware version than STM32MP15. Only EXTI line mapping is changed and
following EXTI lines are supported: GPIO, RTC, I2C[1-5], UxART[1-8],
USBH_EHCI, USBH_OHCI, USB_OTG, LPTIM[1-5], ETH[1-2].
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220202140005.860-3-alexandre.torgue@foss.st.com
Move the reference to the device over to the irq domain.
This allows the irq_chip structure to be directly used instead
of taking a copy for each instance.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220201120310.878267-6-maz@kernel.org
Move the reference to the device over to the irq domain.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220201120310.878267-5-maz@kernel.org
Move the reference to the device over to the irq domain.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220201120310.878267-4-maz@kernel.org
Move the reference to the GIC device over to the irq domain.
This allows for some localised cleanup.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220201120310.878267-3-maz@kernel.org
As we are about to have a PMU driver, move the PMU bits from the AIC
driver into a common include file.
Reviewed-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Add the necessary code to configure and P and E-core PMU interrupts
with their respective affinities. When such an interrupt fires, map
it onto the right pseudo-interrupt.
Reviewed-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
In order to be able to tell the core IRQ code about the affinity
of the PMU interrupt in later patches, parse the affinities kindly
provided in the device-tree.
Signed-off-by: Marc Zyngier <maz@kernel.org>
The thead,c900-plic has been used in opensbi to distinguish
PLIC [1]. Although PLICs have the same behaviors in Linux,
they are different hardware with some custom initializing in
firmware(opensbi).
Qute opensbi patch commit-msg by Samuel:
The T-HEAD PLIC implementation requires setting a delegation bit
to allow access from S-mode. Now that the T-HEAD PLIC has its own
compatible string, set this bit automatically from the PLIC driver,
instead of reaching into the PLIC's MMIO space from another driver.
[1]: 78c2b19218
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Cc: Anup Patel <anup@brainfault.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Samuel Holland <samuel@sholland.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220130135634.1213301-3-guoren@kernel.org
We have some systems out there that have both LPI support and an
ITS, but that don't expose the ITS in their firmware tables
(either because it is broken or because they run under a hypervisor
that hides it...).
Is such a configuration, we still register the HP notifier to free
the allocated tables if needed, resulting in a warning as there is
no memory to free (nothing was allocated the first place).
Fix it by keying the HP notifier on the presence of at least one
sucessfully probed ITS.
Fixes: d23bc2bc1d ("irqchip/gic-v3-its: Postpone LPI pending table freeing and memreserve")
Reported-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lore.kernel.org/r/20220202103454.2480465-1-maz@kernel.org
- Drop an unused private data field in the AIC driver
- Various fixes to the realtek-rtl driver
- Make the GICv3 ITS driver compile again in !SMP configurations
- Force reset of the GICv3 ITSs at probe time to avoid issues during kexec
- Yet another kfree/bitmap_free conversion
- Various DT updates (Renesas, SiFive)
-----BEGIN PGP SIGNATURE-----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=0mrS
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
- Drop an unused private data field in the AIC driver
- Various fixes to the realtek-rtl driver
- Make the GICv3 ITS driver compile again in !SMP configurations
- Force reset of the GICv3 ITSs at probe time to avoid issues during kexec
- Yet another kfree/bitmap_free conversion
- Various DT updates (Renesas, SiFive)
Link: https://lore.kernel.org/r/20220128174217.517041-1-maz@kernel.org
A recent bug report outlined that the way GICv4.1 is handled across
kexec is pretty bad. We can end-up in a situation where ITSs share
memory (this is the case when SVPET==1) and reprogram the base
registers, creating a situation where ITSs that are part of a given
affinity group see different pointers. Which is illegal. Boo.
In order to restore some sanity, reset the BASERn registers to 0
*before* probing any ITS. Although this isn't optimised at all,
this is only a once-per-boot cost, which shouldn't show up on
anyone's radar.
Cc: Jay Chen <jkchen@linux.alibaba.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20211216190315.GA14220@lpieralisi
Link: https://lore.kernel.org/r/20220124133809.1291195-1-maz@kernel.org
Commit 835f442fdb ("irqchip/gic-v3-its: Limit memreserve cpuhp state
lifetime") added a reference to cpus_booted_once_mask, which does not
exist on !SMP builds, breaking the build for such configurations.
Given the intent of the check, short circuit it to always pass.
Cc: Valentin Schneider <valentin.schneider@arm.com>
Fixes: 835f442fdb ("irqchip/gic-v3-its: Limit memreserve cpuhp state lifetime")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220122151614.133766-1-ardb@kernel.org
Instead of only servicing the lowest pending interrupt line, make sure
all pending SoC interrupts are serviced before exiting the chained
handler. This adds a small overhead if only one interrupt is pending,
but should prevent rapid re-triggering of the handler.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/5082ad3cb8b4eedf55075561b93eff6570299fe1.1641739718.git.sander@svanheule.net
There is an offset between routing values (1..6) and the connected MIPS
CPU interrupts (2..7), but no distinction was made between these two
values.
This issue was previously hidden during testing, because an interrupt
mapping was used where for each required interrupt another (unused)
routing was configured, with an offset of +1.
Offset the CPU IRQ numbers by -1 to retrieve the correct routing value.
Fixes: 9f3a0f34b8 ("irqchip: Add support for Realtek RTL838x/RTL839x interrupt controller")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/177b920aa8d8610615692d0e657e509f363c85ca.1641739718.git.sander@svanheule.net
The driver assigned the irqchip and irq handler to the hardware irq,
instead of the virq. This is incorrect, and only worked because these
irq numbers happened to be the same on the devices used for testing the
original driver.
Fixes: 9f3a0f34b8 ("irqchip: Add support for Realtek RTL838x/RTL839x interrupt controller")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/4b4936606480265db47df152f00bc2ed46340599.1641739718.git.sander@svanheule.net
Treewide cleanup and consolidation of MSI interrupt handling in
preparation for further changes in this area which are necessary to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space
-----BEGIN PGP SIGNATURE-----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=vKzd
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI irq updates from Thomas Gleixner:
"Rework of the MSI interrupt infrastructure.
This is a treewide cleanup and consolidation of MSI interrupt handling
in preparation for further changes in this area which are necessary
to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space"
* tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
genirq/msi: Populate sysfs entry only once
PCI/MSI: Unbreak pci_irq_get_affinity()
genirq/msi: Convert storage to xarray
genirq/msi: Simplify sysfs handling
genirq/msi: Add abuse prevention comment to msi header
genirq/msi: Mop up old interfaces
genirq/msi: Convert to new functions
genirq/msi: Make interrupt allocation less convoluted
platform-msi: Simplify platform device MSI code
platform-msi: Let core code handle MSI descriptors
bus: fsl-mc-msi: Simplify MSI descriptor handling
soc: ti: ti_sci_inta_msi: Remove ti_sci_inta_msi_domain_free_irqs()
soc: ti: ti_sci_inta_msi: Rework MSI descriptor allocation
NTB/msi: Convert to msi_on_each_desc()
PCI: hv: Rework MSI handling
powerpc/mpic_u3msi: Use msi_for_each-desc()
powerpc/fsl_msi: Use msi_for_each_desc()
powerpc/pasemi/msi: Convert to msi_on_each_dec()
powerpc/cell/axon_msi: Convert to msi_on_each_desc()
powerpc/4xx/hsta: Rework MSI handling
...
- Fix GICv3 redistributor table reservation with RT across kexec
- Fix GICv4.1 redistributor view of the VPE table across kexec
- Add support for extra interrupts on spear-shirq
- Make obtaining some interrupts optional for the Renesas drivers
- Various cleanups and bug fixes
-----BEGIN PGP SIGNATURE-----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=MDM3
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- Fix GICv3 redistributor table reservation with RT across kexec
- Fix GICv4.1 redistributor view of the VPE table across kexec
- Add support for extra interrupts on spear-shirq
- Make obtaining some interrupts optional for the Renesas drivers
- Various cleanups and bug fixes
Link: https://lore.kernel.org/lkml/20220108130807.4109738-1-maz@kernel.org
* irq/misc-5.17:
: .
: Misc irqchip fixes:
:
: - Disable GICv4.1 RD's VPE table at boot time to avoid RAS errors
: - Fix Ingenic TCU's u32/unsigned long abuse
: - Some GICv2m constifying
: - Mark imx_gpcv2_instance as __ro_after_init
: - Enable a few missing IRQs on Spear
: - Conversion to platform_get_irq_optional() for the Renesas irqchips
: .
irqchip/renesas-intc-irqpin: Use platform_get_irq_optional() to get the interrupt
irqchip/renesas-irqc: Use platform_get_irq_optional() to get the interrupt
irqchip/gic-v4: Disable redistributors' view of the VPE table at boot time
irqchip/ingenic-tcu: Use correctly sized arguments for bit field
irqchip/gic-v2m: Add const to of_device_id
irqchip/imx-gpcv2: Mark imx_gpcv2_instance with __ro_after_init
irqchip/spear-shirq: Add support for IRQ 0..6
Signed-off-by: Marc Zyngier <maz@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypassed the hierarchical setup and messed up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_optional().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211216182121.5323-1-prabhakar.mahadev-lad.rj@bp.renesas.com
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypassed the hierarchical setup and messed up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_optional().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211216182121.5323-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Use the common msi_index member and get rid of the pointless wrapper struct.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20211210221814.540704224@linutronix.de
It's hard to distinguish what platform_msi_domain_alloc() and
platform_msi_domain_alloc_irqs() are about. Make the distinction more
explicit and add comments which explain the use cases properly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20211210221814.228706214@linutronix.de
The only unconditional part of MSI data in struct device is the irqdomain
pointer. Everything else can be allocated on demand. Create a data
structure and move the irqdomain pointer into it. The other MSI specific
parts are going to be removed from struct device in later steps.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211210221813.617178827@linutronix.de
Jay Chen reported that using a kdump kernel on a GICv4.1 system
results in a RAS error being delivered when the secondary kernel
configures the ITS's view of the new VPE table.
As it turns out, that's because each RD still has a pointer to
the previous instance of the VPE table, and that particular
implementation is very upset by seeing two bits of the HW that
should point to the same table with different values.
To solve this, let's invalidate any reference that any RD has to
the VPE table when discovering the RDs. The ITS can then be
programmed as expected.
Reported-by: Jay Chen <jkchen@linux.alibaba.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20211214064716.21407-1-jkchen@linux.alibaba.com
Link: https://lore.kernel.org/r/20211216144804.1578566-1-maz@kernel.org
The find.h APIs are designed to be used only on unsigned long arguments.
This can technically result in a over-read, but it is harmless in this
case. Regardless, fix it to avoid the warning seen under -Warray-bounds,
which we'd like to enable globally:
In file included from ./include/linux/bitmap.h:9,
from ./include/linux/cpumask.h:12,
from ./include/linux/smp.h:13,
from ./include/linux/lockdep.h:14,
from ./include/linux/mutex.h:17,
from ./include/linux/notifier.h:14,
from ./include/linux/clk.h:14,
from drivers/irqchip/irq-ingenic-tcu.c:7:
drivers/irqchip/irq-ingenic-tcu.c: In function 'ingenic_tcu_intc_cascade':
./include/linux/find.h:40:23: warning: array subscript 'long unsigned int[0]' is partly outside array bounds of 'uint32_t[1]' {aka 'unsigned int[1]'} [-Warray-bounds]
40 | val = *addr & GENMASK(size - 1, offset);
| ^~~~~
drivers/irqchip/irq-ingenic-tcu.c:30:18: note: while referencing 'irq_reg'
30 | uint32_t irq_reg, irq_mask;
| ^~~~~~~
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211215232457.2069969-1-keescook@chromium.org
imx_gpcv2_instance will not be updated after init, so mark it with
__ro_after_init.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211214084711.1357325-1-peng.fan@oss.nxp.com
IRQ 0..7 are not supported by the driver for SPEAr320 SOC family.
IRQ 0 is not reserved in SPEAr320 SOC (assigned to GPIOINT).
Furthermore, in SPEAr320s SOC variant, IRQ 0..6 are assigned
as follow:
IRQ 6 - NGPIO_INTR: Combined status of edge programmable
interrupts from GPIO ports
IRQ 5 - TX_OR_INTR: I2S interrupt on Transmit FIFO overrun
IRQ 4 - TX_EMP_INTR: I2S interrupt on Transmit FIFO empty
IRQ 3 - RX_OR_INTR: I2S interrupt on Receive FIFO overrun
IRQ 2 - RX_DA_INTR: I2S interrupt on data available in Receive FIFO
IRQ 1 - Reserved
IRQ 0 - GPIO_INTR: Legacy interrupt from GPIO ports
Add support for these IRQs in SPEAr320 SOC family.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211202095255.165797-6-herve.codina@bootlin.com
The new memreserve cpuhp callback only needs to survive up until a point
where every CPU in the system has booted once. Beyond that, it becomes a
no-op and can be put in the bin.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211027151506.2085066-4-valentin.schneider@arm.com
Memory used by the LPI tables have to be made persistent for kexec to have
a chance to work, as explained in [1]. If they have been made persistent
and we are booting into a kexec'd kernel, we also need to free the pages
that were preemptively allocated by the new kernel for those tables.
Both of those operations currently happen during its_cpu_init(), which
happens in a _STARTING (IOW atomic) cpuhp callback for secondary
CPUs. efi_mem_reserve_iomem() issues a GFP_ATOMIC allocation, which
unfortunately doesn't work under PREEMPT_RT (this ends up grabbing a
non-raw spinlock, which can sleep under PREEMPT_RT). Similarly, freeing the
pages ends up grabbing a sleepable spinlock.
Since the memreserve is only required by kexec, it doesn't have to be done
so early in the secondary boot process. Issue the reservation in a new
CPUHP_AP_ONLINE_DYN cpuhp callback, and piggy-back the page freeing on top
of it. A CPU gets to run the body of this new callback exactly once.
As kexec issues a machine_shutdown() prior to machine_kexec(), it will be
serialized vs a CPU being plugged to life by the hotplug machinery - either
the CPU will have been brought up and have had its redistributor's pending
table memreserved, or it never went online and will have its table
allocated by the new kernel.
[1]: https://lore.kernel.org/lkml/20180921195954.21574-1-marc.zyngier@arm.com/
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211027151506.2085066-3-valentin.schneider@arm.com
Later patches will require tracking some per-rdist status. Reuse the bytes
"lost" to padding within the __percpu rdist struct as a flags field, and
re-encode ->lpi_enabled within said flags.
No change in functionality intended.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211027151506.2085066-2-valentin.schneider@arm.com
This was found by coccicheck:
./drivers/irqchip/irq-bcm7120-l2.c,328,1-7,ERROR missing put_device;
call of_find_device_by_node on line 234, but without a corresponding
object release within this function.
./drivers/irqchip/irq-bcm7120-l2.c,341,1-7,ERROR missing put_device;
call of_find_device_by_node on line 234, but without a corresponding
object release within this function.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211109055958.130287-1-ye.guojin@zte.com.cn
There is no point to have this function public as it is set by the PCI core
anyway when a PCI/MSI irqdomain is created.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # PCI
Link: https://lore.kernel.org/r/20211206210224.157070464@linutronix.de
INVALL CMD specifies that the ITS must ensure any caching associated with
the interrupt collection defined by ICID is consistent with the LPI
configuration tables held in memory for all Redistributors. SYNC is
required to ensure that INVALL is executed.
Currently, LPI configuration data may be inconsistent with that in the
memory within a short period of time after the INVALL command is executed.
Signed-off-by: Wudi Wang <wangwudi@hisilicon.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fixes: cc2d3216f5 ("irqchip: GICv3: ITS command queue")
Link: https://lore.kernel.org/r/20211208015429.5007-1-zhangshaokun@hisilicon.com
This function is only called from the driver init code.
Signed-off-by: Donghyeok Kim <dthex5d@gmail.com>
Acked-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211204164228.5920-1-dthex5d@gmail.com
Rather then restructuring the ARMv7M entrly logic per TODO, just move
NVIC to GENERIC_IRQ_MULTI_HANDLER.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
According to ARM(v7M) ARM Interrupt Priority Offsets located at
0xE000E400-0xE000E5EC, while 0xE000E300-0xE000E33C covers read-only
Interrupt Active Bit Registers
Fixes: 292ec08049 ("irqchip: Add support for ARMv7-M NVIC")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211201110259.84857-1-vladimir.murzin@arm.com
The interrupt status bits are cleared by writing 1, we should force a
write to clear the interrupt without checking if the value has changed.
Fixes: 04f605906f ("irqchip: Add Aspeed SCU interrupt controller")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211124094348.11621-1-billy_tsai@aspeedtech.com
Cc: stable@vger.kernel.org
irq-armada-370-xp driver already sets MSI_FLAG_MULTI_PCI_MSI flag into
msi_domain_info structure. But allocated interrupt numbers for Multi-MSI
needs to be properly aligned otherwise devices send MSI interrupt with
wrong number.
Fix this issue by using function bitmap_find_free_region() instead of
bitmap_find_next_zero_area() to allocate aligned interrupt numbers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: a71b9412c9 ("irqchip/armada-370-xp: Allow allocation of multiple MSIs")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211125130057.26705-2-pali@kernel.org
When using "devm_request_threaded_irq(,,,,IRQF_ONESHOT,,)" in a driver,
only the first interrupt is handled, and following interrupts are never
delivered (initially reported in [1]).
That's because the RISC-V PLIC cannot EOI masked interrupts, as explained
in the description of Interrupt Completion in the PLIC spec [2]:
<quote>
The PLIC signals it has completed executing an interrupt handler by
writing the interrupt ID it received from the claim to the claim/complete
register. The PLIC does not check whether the completion ID is the same
as the last claim ID for that target. If the completion ID does not match
an interrupt source that *is currently enabled* for the target, the
completion is silently ignored.
</quote>
Re-enable the interrupt before completion if it has been masked during
the handling, and remask it afterwards.
[1] http://lists.infradead.org/pipermail/linux-riscv/2021-July/007441.html
[2] 8bc15a35d0/riscv-plic.adoc
Fixes: bb0fed1c60 ("irqchip/sifive-plic: Switch to fasteoi flow")
Reported-by: Vincent Pelletier <plr.vincent@gmail.com>
Tested-by: Nikita Shubin <nikita.shubin@maquefel.me>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Cc: stable@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
[maz: amended commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211105094748.3894453-1-guoren@kernel.org
The mask/unmask must be implemented, and enable/disable supplement
them if the HW requires something different at startup time. When
irq source is disabled by mask, mpintc could complete irq normally.
So drop enable/disable if favour of mask/unmask.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211101134534.3804542-1-guoren@kernel.org
* irq/irq_cpu_offline:
: .
: Make irq_cpu_{on,off}line() deprecated kernel API, and only
: enable it for some obscure Cavium platform after having
: moved all the other users away from it.
:
: Next step, drop the platform itself.
: .
genirq: Hide irq_cpu_{on,off}line() behind a deprecated option
irqchip/mips-gic: Get rid of the reliance on irq_cpu_online()
MIPS: loongson64: Drop call to irq_cpu_offline()
Signed-off-by: Marc Zyngier <maz@kernel.org>
* irq/remove-handle-domain-irq-20211026:
: Large rework of the architecture entry code from Mark Rutland.
: From the cover letter:
:
: <quote>
: The handle_domain_{irq,nmi}() functions were oringally intended as a
: convenience, but recent rework to entry code across the kernel tree has
: demonstrated that they cause more pain than they're worth and prevent
: architectures from being able to write robust entry code.
:
: This series reworks the irq code to remove them, handling the necessary
: entry work consistently in entry code (be it architectural or generic).
: </quote>
MIPS: irq: Avoid an unused-variable error
irq: remove handle_domain_{irq,nmi}()
irq: remove CONFIG_HANDLE_DOMAIN_IRQ_IRQENTRY
irq: riscv: perform irqentry in entry code
irq: openrisc: perform irqentry in entry code
irq: csky: perform irqentry in entry code
irq: arm64: perform irqentry in entry code
irq: arm: perform irqentry in entry code
irq: add a (temporary) CONFIG_HANDLE_DOMAIN_IRQ_IRQENTRY
irq: nds32: avoid CONFIG_HANDLE_DOMAIN_IRQ
irq: arc: avoid CONFIG_HANDLE_DOMAIN_IRQ
irq: add generic_handle_arch_irq()
irq: unexport handle_irq_desc()
irq: simplify handle_domain_{irq,nmi}()
irq: mips: simplify do_domain_IRQ()
irq: mips: stop (ab)using handle_domain_irq()
irq: mips: simplify bcm6345_l1_irq_handle()
irq: mips: avoid nested irq_enter()
Signed-off-by: Marc Zyngier <maz@kernel.org>
The MIPS GIC driver uses irq_cpu_online() to go and program the
per-CPU interrupts. However, this method iterates over all IRQs
in the system, despite only 3 per-CPU interrupts being of interest.
Let's be terribly bold and do the iteration ourselves. To ensure
mutual exclusion, hold the gic_lock spinlock that is otherwise
taken while dealing with these interrupts.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20211021170414.3341522-3-maz@kernel.org
Now that entry code handles IRQ entry (including setting the IRQ regs)
before calling irqchip code, irqchip code can safely call
generic_handle_domain_irq(), and there's no functional reason for it to
call handle_domain_irq().
Let's cement this split of responsibility and remove handle_domain_irq()
entirely, updating irqchip drivers to call generic_handle_domain_irq().
For consistency, handle_domain_nmi() is similarly removed and replaced
with a generic_handle_domain_nmi() function which also does not perform
any entry logic.
Previously handle_domain_{irq,nmi}() had a WARN_ON() which would fire
when they were called in an inappropriate context. So that we can
identify similar issues going forward, similar WARN_ON_ONCE() logic is
added to the generic_handle_*() functions, and comments are updated for
clarity and consistency.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
In preparation for removing HANDLE_DOMAIN_IRQ_IRQENTRY, have arch/arm
perform all the irqentry accounting in its entry code.
For configurations with CONFIG_GENERIC_IRQ_MULTI_HANDLER, we can use
generic_handle_arch_irq(). Other than asm_do_IRQ(), all C calls to
handle_IRQ() are from irqchip handlers which will be called from
generic_handle_arch_irq(), so to avoid double accounting IRQ entry, the
entry logic is moved from handle_IRQ() into asm_do_IRQ().
For ARMv7M the entry assembly is tightly coupled with the NVIC irqchip, and
while the entry code should logically live under arch/arm/, moving the
entry logic there makes things more convoluted. So for now, place the
entry logic in the NVIC irqchip, but separated into a separate
function to make the split of responsibility clear.
For all other configurations without CONFIG_GENERIC_IRQ_MULTI_HANDLER,
IRQ entry is already handled in arch code, and requires no changes.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> # ARMv7M
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
In preparation for removing HANDLE_DOMAIN_IRQ, have arch/nds32 perform
all the necessary IRQ entry accounting in its entry code.
Currently arch/nds32 is tightly coupled with the ativic32 irqchip, and
while the entry code should logically live under arch/nds32/, moving the
entry logic there makes things more convoluted. So for now, place the
entry logic in the ativic32 irqchip, but separated into a separate
function to make the split of responsibility clear.
In future this should probably use GENERIC_IRQ_MULTI_HANDLER to cleanly
decouple this.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vincent Chen <deanbo422@gmail.com>
As bcm6345_l1_irq_handle() only needs to know /whether/ an IRQ was
resolved, and doesn't need to know the specific IRQ, it's simpler for it
to call generic_handle_domain_irq() directly and check the return code,
so let's do that.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Suggested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
As bcm6345_l1_irq_handle() is a chained irqchip handler, it will be
invoked within the context of the root irqchip handler, which must have
entered IRQ context already.
When bcm6345_l1_irq_handle() calls arch/mips's do_IRQ() , this will nest
another call to irq_enter(), and the resulting nested increment to
`rcu_data.dynticks_nmi_nesting` will cause rcu_is_cpu_rrupt_from_idle()
to fail to identify wakeups from idle, resulting in failure to preempt,
and RCU stalls.
Chained irqchip handlers must invoke IRQ handlers by way of thee core
irqchip code, i.e. generic_handle_irq() or generic_handle_domain_irq()
and should not call do_IRQ(), which is intended only for root irqchip
handlers.
Fix bcm6345_l1_irq_handle() by calling generic_handle_irq() directly.
Fixes: c7c42ec2ba ("irqchips/bmips: Add bcm6345-l1 interrupt controller")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
* irq/mchp-eic:
: .
: New irqchip driver for the Microchip EIC block
: .
irqchip/mchp-eic: Fix return value check in mchp_eic_init()
irqchip/mchp-eic: Add support for the Microchip EIC
dt-bindings: microchip,eic: Add bindings for the Microchip EIC
Signed-off-by: Marc Zyngier <maz@kernel.org>
* irq/modular-irqchips:
: .
: Update a set of irqchip drivers to be build as modules.
:
: This includes an Amlogic and multiple Broadcom drivers, triggering
: a cascade of other changes (MIPS arch code, symbols being exported,
: config changes)
: .
irqchip: Fix kernel-doc parameter typo for IRQCHIP_DECLARE
ARM: bcm: Removed forced select of interrupt controllers
arm64: broadcom: Removed forced select of interrupt controllers
irqchip/irq-bcm7120-l2: Switch to IRQCHIP_PLATFORM_DRIVER
genirq: Export irq_gc_noop()
irqchip/irq-brcmstb-l2: Switch to IRQCHIP_PLATFORM_DRIVER
genirq: Export irq_gc_{unmask_enable,mask_disable}_reg
irqchip/irq-bcm7038-l1: Switch to IRQCHIP_PLATFORM_DRIVER
irqchip/irq-bcm7038-l1: Restrict affinity setting to MIPS
irqchip/irq-bcm7038-l1: Gate use of CPU logical map to MIPS
irqchip/irq-bcm7038-l1: Use irq_get_irq_data()
irqchip/irq-bcm7038-l1: Remove .irq_cpu_offline()
MIPS: BMIPS: Remove use of irq_cpu_offline
arm64: meson: remove MESON_IRQ_GPIO selection
irqchip/meson-gpio: Make it possible to build as a module
irqchip: Provide stronger type checking for IRQCHIP_MATCH/IRQCHIP_DECLARE
Signed-off-by: Marc Zyngier <maz@kernel.org>
In case of error, the function of_iomap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211025050055.1129845-1-yangyingliang@huawei.com
Allow the user selection and building of this interrupt controller
driver as a module since it is used on ARM/ARM64 based systems as a
second level interrupt controller hanging off the ARM GIC and is
therefore loadable during boot.
To avoid using of_irq_count() which is not exported towards module,
switch the driver to use the platform_device provided by the irqchip
platform driver code and resolve the number of interrupts using
platform_irq_count().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211020184859.2705451-11-f.fainelli@gmail.com
Allow the user selection and building of this interrupt controller
driver as a module since it is used on ARM/ARM64 based systems as a
second level interrupt controller hanging off the ARM GIC and is
therefore loadable during boot.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211020184859.2705451-9-f.fainelli@gmail.com
Allow the user selection and building of this interrupt controller
driver as a module since it is used on ARM/ARM64 based systems as a
second level interrupt controller hanging off the ARM GIC and is
therefore loadable during boot.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211020184859.2705451-7-f.fainelli@gmail.com
Only MIPS based platforms using this interrupt controller as first level
interrupt controller can actually change the affinity of interrupts by
re-programming the affinity mask of the interrupt controller and use
another word group to have another CPU process the interrupt.
When this interrupt is used as a second level interrupt controller on
ARM/ARM64 there is no way to change the interrupt affinity. This fixes a
NULL pointer de-reference while trying to change the affinity since
there is only a single word group in that case, and we would have been
overruning the intc->cpus[] array.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211020184859.2705451-6-f.fainelli@gmail.com
The use of the cpu_logical_map[] array is only relevant for MIPS based
platform where this driver is used as a first level interrupt controller
and contains multiple register groups to map with an associated CPU.
On ARM/ARM64 based systems this interrupt controller is present and used
as a second level interrupt controller hanging off the ARM GIC. That
copy of the interrupt controller contains a single group, resulting in
the intc->cpus[] array to be of size 1.
Things happened to work in that case because we install that interrupt
controller as a chained handler which does not allow it to be affine to
any CPU but the boot CPU which happens to be 0, therefore we never
de-reference past intc->cpus[] but with the current code in place, we do
leave a chance of de-referencing the array past its bounds.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211020184859.2705451-5-f.fainelli@gmail.com
Using irq_desc_get_irq_data(irq_to_desc()) to retrieve the irq_data
structure from a virtual interrupt number is going to be problematic to
make irq-bcm7038-l1 a module because irq_to_desc() is not exported, and
there is no intent to export it to modules, see 64a1b95bb9 ("genirq:
Restrict export of irq_to_desc()").
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211020184859.2705451-4-f.fainelli@gmail.com
With arch/mips/kernel/smp-bmips.c having been migrated away from
irq_cpu_offline() and use irq_migrate_all_off_this_cpu() instead, we no
longer need to implement an .irq_cpu_offline() callback. This is a
necessary change to facilitate the building of this driver as a module.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211020184859.2705451-3-f.fainelli@gmail.com
Add support for Microchip External Interrupt Controller. The controller
supports 2 external interrupt lines. For every external input there is
a connection to GIC. The interrupt controllers contains only 4
registers:
- EIC_GFCS (read only): which indicates that glitch filter configuration
is ready (not addressed in this implementation)
- EIC_SCFG0R, EIC_SCFG1R (read, write): allows per interrupt specific
settings: enable, polarity/edge settings, glitch filter settings
- EIC_WPMR, EIC_WPSR: enables write protection mode specific settings
(which are architecture specific) for the controller and are not
addressed in this implementation
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210927063657.2157676-3-claudiu.beznea@microchip.com
In order to reduce the kernel Image size on multi-platform distributions,
make it possible to build the Amlogic GPIO IRQ controller as a module
by switching it to a platform driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Saravana Kannan <saravanak@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210902134914.176986-2-narmstrong@baylibre.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210908105723.1831-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210908105715.1780-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210908105708.1729-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210908105701.1678-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210908105653.1627-1-caihuoqing@baidu.com
Geert reported that the GIC driver locks up on a Renesas system
since 005c34ae4b ("irqchip/gic: Atomically update affinity")
fixed the driver to use writeb_relaxed() instead of writel_relaxed().
As it turns out, the interconnect used on this system mandates
32bit wide accesses for all MMIO transactions, even if the GIC
architecture specifically mandates for some registers to be byte
accessible. Gahhh...
Work around the issue by crudly detecting the offending system,
and falling back to an inefficient RMW+lock implementation.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/CAMuHMdV+Ev47K5NO8XHsanSq5YRMCHn2gWAQyV-q2LpJVy9HiQ@mail.gmail.com
This code works, but it is cleaner to use semicolons at the end of
statements instead of commas.
Extracted from a big anonymous patch by Julia Lawall
<julia.lawall@inria.fr>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/b1710bb6ea5faa7a7fe74404adb0beb951e0bf8c.1631699160.git.geert+renesas@glider.be
In its_vpe_irq_domain_alloc, when its_vpe_init() returns an error,
there is an off-by-one in the number of VPEs to be freed.
Fix it by simply passing the number of VPEs allocated, which is the
index of the loop iterating over the VPEs.
Fixes: 7d75bbb4bc ("irqchip/gic-v3-its: Add VPE irq domain allocation/teardown")
Signed-off-by: Kaige Fu <kaige.fu@linux.alibaba.com>
[maz: fixed commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/d9e36dee512e63670287ed9eff884a5d8d6d27f2.1631672311.git.kaige.fu@linux.alibaba.com
Fix kernel-doc warnings in irq-mbigen.c:
irq-mbigen.c:29: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* In mbigen vector register
irq-mbigen.c:43: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* offset of clear register in mbigen node
irq-mbigen.c:50: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* offset of interrupt type register
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Jun Ma <majun258@huawei.com>
Cc: Yun Wu <wuyun.wu@huawei.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Aditya Srivastava <yashsri421@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210905033644.15988-1-rdunlap@infradead.org
When converting the driver to using handle_percpu_devid_irq,
we forgot to repaint the irq_eoi() callback into irq_ack(),
as handle_percpu_devid_fasteoi_ipi() was actually using EOI
really early in the handling. Yes this was a stupid idea.
Fix this by using the HW ack method as irq_ack().
Fixes: e52e73b7e9 ("irqchip/armada-370-xp: Make IPIs use handle_percpu_devid_irq()")
Reported-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87tuiexq5f.fsf@pengutronix.de
* irq/qcom-pdc-nowake-cleanup:
: Fix the QCOM PDC mishandling of the interrupt hierarchy by trimming
: it when necessary.
: Export irq_domain_disconnect_hierarchy as a consequence of it.
irqchip/qcom-pdc: Trim unused levels of the interrupt hierarchy
irqdomain: Export irq_domain_disconnect_hierarchy()
Signed-off-by: Marc Zyngier <maz@kernel.org>
The QCOM PDC driver creates a bunch of unnecessary levels in
the interrupt hierarchy when dealing with non-wakeup-capable
interrupts. By definition, these lines are terminated at the
PDC level, and everything below this is completely fake.
This also results in additional complexity as most of the
callbacks have to check for the validity of the parent level.
Needless to say, this doesn't look very good.
Solve this by disconnecting the interrupt hierarchy below
the last valid level, and considerably simplify the handling
of all the other interrupts by avoiding now unnecessary cheks.
In most cases, the standard irq_*_parent() handlers are directly
used.
This also cures an issue reporting by Maulik where gpio_to_irq()
returns an error after having observed a set of invalid levels.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1629705880-27877-3-git-send-email-mkshah@codeaurora.org
* irq/misc-5.15:
: .
: Various irqchip fixes:
:
: - Fix edge interrupt support on loongson systems
: - Advertise lack of wake-up logic on mtk-sysirq
: - Fix mask tracking on the Apple AIC
: - Correct priority reading of arm64 pseudo-NMI when SCR_EL3.FIQ==0
: .
irqchip/gic-v3: Fix priority comparison when non-secure priorities are used
irqchip/apple-aic: Fix irq_disable from within irq handlers
Signed-off-by: Marc Zyngier <maz@kernel.org>
When non-secure priorities are used, compared to the raw priority set,
the value read back from RPR is also right-shifted by one and the
highest bit set.
Add a macro to do the modifications to the raw priority when doing the
comparison against the RPR value. This corrects the pseudo-NMI behavior
when non-secure priorities in the GIC are used. Tested on 5.10 with
the "IPI as pseudo-NMI" series [1] applied on MT8195.
[1] https://lore.kernel.org/linux-arm-kernel/1604317487-14543-1-git-send-email-sumit.garg@linaro.org/
Fixes: 3367805909 ("irqchip/gic-v3: Support pseudo-NMIs when SCR_EL3.FIQ == 0")
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
[maz: Added comment contributed by Alex]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210811171505.1502090-1-wenst@chromium.org
When disable_irq_nosync for an interrupt is called from within its
interrupt handler, this interrupt is only marked as disabled with the
intention to mask it when it triggers again.
The AIC hardware however automatically masks the interrupt when it is read.
aic_irq_eoi then unmasks it again if it's not disabled *and* not masked.
This results in a state mismatch between the hardware state and the
state kept in irq_data: The hardware interrupt is masked but
IRQD_IRQ_MASKED is not set. Any further calls to unmask_irq will directly
return and the interrupt can never be enabled again.
Fix this by keeping the hardware and irq_data state in sync by unmasking in
aic_irq_eoi if and only if the irq_data state also assumes the interrupt to
be unmasked.
Fixes: 76cde26394 ("irqchip/apple-aic: Add support for the Apple Interrupt Controller")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210812100942.17206-1-sven@svenpeter.dev
- Fix edge interrupt support on loongson systems
- Advertise lack of wake-up logic on mtk-sysirq
* irq/misc-5.15:
irqchip/mtk-sysirq: Skip setting irq-wake
irqchip/loongson-pch-pic: Improve edge triggered interrupt support
Signed-off-by: Marc Zyngier <maz@kernel.org>
mtk-sysirq doesn't require specific logic to work with wakeup IRQs. To
allow registered IRQs to be used as a wakeup-source, add the flag
IRQCHIP_SKIP_SET_WAKE.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210707062004.782787-1-msp@baylibre.com
- Add support for partitionned EPPIs, modeled after the existing
partitioned PPI support
* irq/gicv3-eppi-partition:
irqchip/gic-v3: Fix selection of partition domain for EPPIs
irqchip/gic-v3: Add __gic_get_ppi_index() to find the PPI number from hwirq
Signed-off-by: Marc Zyngier <maz@kernel.org>
commit 5f51f80382 ("irqchip/gic-v3: Add EPPI range support") added
GIC_IRQ_TYPE_PARTITION support for EPPI to gic_irq_domain_translate(),
and commit 52085d3f20 ("irqchip/gic-v3: Dynamically allocate PPI
partition descriptors") made the gic_data.ppi_descs array big enough for
EPPI, but neither gic_irq_domain_select() nor partition_domain_translate()
were updated.
This means partitions are created by partition_create_desc() for the
EPPI range, but can't be registered as they will always match the root
domain and map to the summary interrupt.
Update gic_irq_domain_select() to match PPI and EPPI. The fwspec for
PPI and EPPI both start from 0. Use gic_irq_domain_translate() to find
the hwirq from the fwspec, then convert this to a ppi index.
Reported-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210729172748.28841-3-james.morse@arm.com
gic_get_ppi_index() is a useful concept for ppi partitions, as the GIC
has two PPI ranges but needs mapping to a single range when used as an
index in the gic_data.ppi_descs[] array.
Add a double-underscore version which takes just the intid. This will
be used in the partition domain select and translate helpers to enable
partition support for the EPPI range.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210729172748.28841-2-james.morse@arm.com
Edge-triggered mode and level-triggered mode need different handlers,
and edge-triggered mode need a specific ack operation. So improve it.
Fixes: ef8c01eb64 ("irqchip: Add Loongson PCH PIC controller")
Signed-off-by: Chen Zhu <zhuchen@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210805132216.3539007-1-chenhuacai@loongson.cn
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210618151657.65305-7-andriy.shevchenko@linux.intel.com
Switch to devm_bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210618151657.65305-6-andriy.shevchenko@linux.intel.com
Switch to devm_bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210618151657.65305-5-andriy.shevchenko@linux.intel.com
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210618151657.65305-4-andriy.shevchenko@linux.intel.com
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210618151657.65305-3-andriy.shevchenko@linux.intel.com
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210618151657.65305-2-andriy.shevchenko@linux.intel.com
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210618151657.65305-1-andriy.shevchenko@linux.intel.com
- Fix a MIPS bug where irqdomain loopkups could occur in a context
where RCU is not allowed
- Fix a documentation bug for handle_domain_irq
-----BEGIN PGP SIGNATURE-----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=eTw3
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
- Fix a MIPS bug where irqdomain loopkups could occur in a context
where RCU is not allowed
- Fix a documentation bug for handle_domain_irq
Since d4a45c68dc ("irqdomain: Protect the linear revmap with RCU"),
any irqdomain lookup requires the RCU read lock to be held.
This assumes that the architecture code will be structured such as
irq_enter() will be called *before* the interrupt is looked up
in the irq domain. However, this isn't the case for MIPS, and a number
of drivers are structured to do it the other way around when handling
an interrupt in their root irqchip (secondary irqchips are OK by
construction).
This results in a RCU splat on a lockdep-enabled kernel when the kernel
takes an interrupt from idle, as reported by Guenter Roeck.
Note that this could have fired previously if any driver had used
tree-based irqdomain, which always had the RCU requirement.
To solve this, provide a MIPS-specific helper (do_domain_IRQ())
as the pendent of do_IRQ() that will do thing in the right order
(and maybe save some cycles in the process).
Ideally, MIPS would be moved over to using handle_domain_irq(),
but that's much more ambitious.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
[maz: add dependency on CONFIG_IRQ_DOMAIN after report from the kernelci bot]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20210705172352.GA56304@roeck-us.net
Link: https://lore.kernel.org/r/20210706110647.3979002-1-maz@kernel.org
Core changes:
- Cleanup and simplification of common code to invoke the low level
interrupt flow handlers when this invocation requires irqdomain
resolution. Add the necessary core infrastructure.
- Provide a proper interface for modular PMU drivers to set the
interrupt affinity.
- Add a request flag which allows to exclude interrupts from spurious
interrupt detection. Useful especially for IPI handlers which always
return IRQ_HANDLED which turns the spurious interrupt detection into a
pointless waste of CPU cycles.
Driver changes:
- Bulk convert interrupt chip drivers to the new irqdomain low level flow
handler invocation mechanism.
- Add device tree bindings for the Renesas R-Car M3-W+ SoC
- Enable modular build of the Qualcomm PDC driver
- The usual small fixes and improvements.
-----BEGIN PGP SIGNATURE-----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=FIKh
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2021-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core changes:
- Cleanup and simplification of common code to invoke the low level
interrupt flow handlers when this invocation requires irqdomain
resolution. Add the necessary core infrastructure.
- Provide a proper interface for modular PMU drivers to set the
interrupt affinity.
- Add a request flag which allows to exclude interrupts from spurious
interrupt detection. Useful especially for IPI handlers which
always return IRQ_HANDLED which turns the spurious interrupt
detection into a pointless waste of CPU cycles.
Driver changes:
- Bulk convert interrupt chip drivers to the new irqdomain low level
flow handler invocation mechanism.
- Add device tree bindings for the Renesas R-Car M3-W+ SoC
- Enable modular build of the Qualcomm PDC driver
- The usual small fixes and improvements"
* tag 'irq-core-2021-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (38 commits)
dt-bindings: interrupt-controller: arm,gic-v3: Describe GICv3 optional properties
irqchip: gic-pm: Remove redundant error log of clock bulk
irqchip/sun4i: Remove unnecessary oom message
irqchip/irq-imx-gpcv2: Remove unnecessary oom message
irqchip/imgpdc: Remove unnecessary oom message
irqchip/gic-v3-its: Remove unnecessary oom message
irqchip/gic-v2m: Remove unnecessary oom message
irqchip/exynos-combiner: Remove unnecessary oom message
irqchip: Bulk conversion to generic_handle_domain_irq()
genirq: Move non-irqdomain handle_domain_irq() handling into ARM's handle_IRQ()
genirq: Add generic_handle_domain_irq() helper
irqchip/nvic: Convert from handle_IRQ() to handle_domain_irq()
irqdesc: Fix __handle_domain_irq() comment
genirq: Use irq_resolve_mapping() to implement __handle_domain_irq() and co
irqdomain: Introduce irq_resolve_mapping()
irqdomain: Protect the linear revmap with RCU
irqdomain: Cache irq_data instead of a virq number in the revmap
irqdomain: Use struct_size() helper when allocating irqdomain
irqdomain: Make normal and nomap irqdomains exclusive
powerpc: Move the use of irq_domain_add_nomap() behind a config option
...
- Add MTE support in guests, complete with tag save/restore interface
- Reduce the impact of CMOs by moving them in the page-table code
- Allow device block mappings at stage-2
- Reduce the footprint of the vmemmap in protected mode
- Support the vGIC on dumb systems such as the Apple M1
- Add selftest infrastructure to support multiple configuration
and apply that to PMU/non-PMU setups
- Add selftests for the debug architecture
- The usual crop of PMU fixes
PPC:
- Support for the H_RPT_INVALIDATE hypercall
- Conversion of Book3S entry/exit to C
- Bug fixes
S390:
- new HW facilities for guests
- make inline assembly more robust with KASAN and co
x86:
- Allow userspace to handle emulation errors (unknown instructions)
- Lazy allocation of the rmap (host physical -> guest physical address)
- Support for virtualizing TSC scaling on VMX machines
- Optimizations to avoid shattering huge pages at the beginning of live migration
- Support for initializing the PDPTRs without loading them from memory
- Many TLB flushing cleanups
- Refuse to load if two-stage paging is available but NX is not (this has
been a requirement in practice for over a year)
- A large series that separates the MMU mode (WP/SMAP/SMEP etc.) from
CR0/CR4/EFER, using the MMU mode everywhere once it is computed
from the CPU registers
- Use PM notifier to notify the guest about host suspend or hibernate
- Support for passing arguments to Hyper-V hypercalls using XMM registers
- Support for Hyper-V TLB flush hypercalls and enlightened MSR bitmap on
AMD processors
- Hide Hyper-V hypercalls that are not included in the guest CPUID
- Fixes for live migration of virtual machines that use the Hyper-V
"enlightened VMCS" optimization of nested virtualization
- Bugfixes (not many)
Generic:
- Support for retrieving statistics without debugfs
- Cleanups for the KVM selftests API
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmDV9UYUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroOIRgf/XX8fKLh24RnTOs2ldIu2AfRGVrT4
QMrr8MxhmtukBAszk2xKvBt8/6gkUjdaIC3xqEnVjxaDaUvZaEtP7CQlF5JV45rn
iv1zyxUKucXrnIOr+gCioIT7qBlh207zV35ArKioP9Y83cWx9uAs22pfr6g+7RxO
h8bJZlJbSG6IGr3voANCIb9UyjU1V/l8iEHqRwhmr/A5rARPfD7g8lfMEQeGkzX6
+/UydX2fumB3tl8e2iMQj6vLVdSOsCkehvpHK+Z33EpkKhan7GwZ2sZ05WmXV/nY
QLAYfD10KegoNWl5Ay4GTp4hEAIYVrRJCLC+wnLdc0U8udbfCuTC31LK4w==
=NcRh
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"This covers all architectures (except MIPS) so I don't expect any
other feature pull requests this merge window.
ARM:
- Add MTE support in guests, complete with tag save/restore interface
- Reduce the impact of CMOs by moving them in the page-table code
- Allow device block mappings at stage-2
- Reduce the footprint of the vmemmap in protected mode
- Support the vGIC on dumb systems such as the Apple M1
- Add selftest infrastructure to support multiple configuration and
apply that to PMU/non-PMU setups
- Add selftests for the debug architecture
- The usual crop of PMU fixes
PPC:
- Support for the H_RPT_INVALIDATE hypercall
- Conversion of Book3S entry/exit to C
- Bug fixes
S390:
- new HW facilities for guests
- make inline assembly more robust with KASAN and co
x86:
- Allow userspace to handle emulation errors (unknown instructions)
- Lazy allocation of the rmap (host physical -> guest physical
address)
- Support for virtualizing TSC scaling on VMX machines
- Optimizations to avoid shattering huge pages at the beginning of
live migration
- Support for initializing the PDPTRs without loading them from
memory
- Many TLB flushing cleanups
- Refuse to load if two-stage paging is available but NX is not (this
has been a requirement in practice for over a year)
- A large series that separates the MMU mode (WP/SMAP/SMEP etc.) from
CR0/CR4/EFER, using the MMU mode everywhere once it is computed
from the CPU registers
- Use PM notifier to notify the guest about host suspend or hibernate
- Support for passing arguments to Hyper-V hypercalls using XMM
registers
- Support for Hyper-V TLB flush hypercalls and enlightened MSR bitmap
on AMD processors
- Hide Hyper-V hypercalls that are not included in the guest CPUID
- Fixes for live migration of virtual machines that use the Hyper-V
"enlightened VMCS" optimization of nested virtualization
- Bugfixes (not many)
Generic:
- Support for retrieving statistics without debugfs
- Cleanups for the KVM selftests API"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (314 commits)
KVM: x86: rename apic_access_page_done to apic_access_memslot_enabled
kvm: x86: disable the narrow guest module parameter on unload
selftests: kvm: Allows userspace to handle emulation errors.
kvm: x86: Allow userspace to handle emulation errors
KVM: x86/mmu: Let guest use GBPAGES if supported in hardware and TDP is on
KVM: x86/mmu: Get CR4.SMEP from MMU, not vCPU, in shadow page fault
KVM: x86/mmu: Get CR0.WP from MMU, not vCPU, in shadow page fault
KVM: x86/mmu: Drop redundant rsvd bits reset for nested NPT
KVM: x86/mmu: Optimize and clean up so called "last nonleaf level" logic
KVM: x86: Enhance comments for MMU roles and nested transition trickiness
KVM: x86/mmu: WARN on any reserved SPTE value when making a valid SPTE
KVM: x86/mmu: Add helpers to do full reserved SPTE checks w/ generic MMU
KVM: x86/mmu: Use MMU's role to determine PTTYPE
KVM: x86/mmu: Collapse 32-bit PAE and 64-bit statements for helpers
KVM: x86/mmu: Add a helper to calculate root from role_regs
KVM: x86/mmu: Add helper to update paging metadata
KVM: x86/mmu: Don't update nested guest's paging bitmasks if CR0.PG=0
KVM: x86/mmu: Consolidate reset_rsvds_bits_mask() calls
KVM: x86/mmu: Use MMU role_regs to get LA57, and drop vCPU LA57 helper
KVM: x86/mmu: Get nested MMU's root level from the MMU's role
...
- Fix GICv3 NMI handling where an IRQ could be mistakenly handled
as a NMI, with disatrous effects
-----BEGIN PGP SIGNATURE-----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=yKDo
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
- Fix GICv3 NMI handling where an IRQ could be mistakenly handled
as a NMI, with disatrous effects
Link: https://lore.kernel.org/r/20210610171127.2404752-1-maz@kernel.org
Various minor irqchip driver updates:
- QC PDC now compiles as a module
- HiSilicon MBIGEN fix for compile-time warning when !ACPI
* irq/irqchip-driver-updates:
irqchip/mbigen: Fix compile warning when CONFIG_ACPI is disabled
irqchip/qcom-pdc: Switch to IRQCHIP_PLATFORM_DRIVER and allow as a module
Simplify the handling of interrupts that require an IRQ domain
resolution:
- domains now cache the irqdata instead of the irq number
- consistent behaviour wrt RCU
- single lookup for architectures using sparse IRQs
- reduced boilerplate code in drivers.
* irq/generic_handle_domain_irq-core: (26 commits)
irqchip: Bulk conversion to generic_handle_domain_irq()
genirq: Move non-irqdomain handle_domain_irq() handling into ARM's handle_IRQ()
genirq: Add generic_handle_domain_irq() helper
irqchip/nvic: Convert from handle_IRQ() to handle_domain_irq()
irqdesc: Fix __handle_domain_irq() comment
genirq: Use irq_resolve_mapping() to implement __handle_domain_irq() and co
irqdomain: Introduce irq_resolve_mapping()
irqdomain: Protect the linear revmap with RCU
irqdomain: Cache irq_data instead of a virq number in the revmap
irqdomain: Use struct_size() helper when allocating irqdomain
irqdomain: Make normal and nomap irqdomains exclusive
powerpc: Move the use of irq_domain_add_nomap() behind a config option
irqdomain: Reimplement irq_linear_revmap() with irq_find_mapping()
irqdomain: Kill irq_domain_add_legacy_isa
powerpc: Drop dependency between asm/irq.h and linux/irqdomain.h
powerpc: Convert irq_domain_add_legacy_isa use to irq_domain_add_legacy
scsi/ibmvscsi: Directly include linux/{of.h,irqdomain.h}
powerpc: Add missing linux/{of.h,irqdomain.h} include directives
MIPS: Do not include linux/irqdomain.h from asm/irq.h
MIPS: Add missing linux/irqdomain.h includes
...
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609141428.14737-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609141150.14637-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609140828.14584-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609140643.14531-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609140534.14478-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210609140335.14425-1-thunder.leizhen@huawei.com
The arm64 entry code suffers from an annoying issue on taking
a NMI, as it sets PMR to a value that actually allows IRQs
to be acknowledged. This is done for consistency with other parts
of the code, and is in the process of being fixed. This shouldn't
be a problem, as we are not enabling interrupts whilst in NMI
context.
However, in the infortunate scenario that we took a spurious NMI
(retired before the read of IAR) *and* that there is an IRQ pending
at the same time, we'll ack the IRQ in NMI context. Too bad.
In order to avoid deadlocks while running something like perf,
teach the GICv3 driver about this situation: if we were in
a context where no interrupt should have fired, transiently
set PMR to a value that only allows NMIs before acking the pending
interrupt, and restore the original value after that.
This papers over the core issue for the time being, and makes
NMIs great again. Sort of.
Fixes: 4d6a38da8e ("arm64: entry: always set GIC_PRIO_PSR_I_SET during entry")
Co-developed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/lkml/20210610145731.1350460-1-maz@kernel.org
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Given that the nvic driver is fully irqdomain aware, there is no
reason for it to use the arch-specific handle_IRQ(), and it can
be moved over to handle_domain_irq().
Signed-off-by: Marc Zyngier <maz@kernel.org>
This drivers currently obtains linux/irqdomain.h by luck and
a chain of bizarre inclusions, which we're about to fix.
Let's include the required file directly.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fix the following compile warning:
drivers/irqchip/irq-mbigen.c:372:36: warning: ‘mbigen_acpi_match’ defined but not used [-Wunused-const-variable=]
static const struct acpi_device_id mbigen_acpi_match[] = {
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210519050455.1693953-1-yangyingliang@huawei.com
This patch revives changes from Saravana Kannan to switch the
qcom-pdc driver to use IRQCHIP_PLATFORM_DRIVER helper macros,
and allows qcom-pdc driver to be loaded as a permanent module.
Earlier attempts at this ran into trouble with loading
dependencies, but with Saravana's fw_devlink=on set by default
now we should avoid those.
[jstultz: Folded in with my changes to allow the driver to be
loadable as a permenent module]
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maulik Shah <mkshah@codeaurora.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: iommu@lists.linux-foundation.org
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210518211922.3474368-1-john.stultz@linaro.org
The CPUs in the Apple M1 SoC partially implement a virtual GICv3
CPU interface, although one that is incapable of HW deactivation
of interrupts, nor masking the maintenance interrupt.
Advertise the support to KVM.
Signed-off-by: Marc Zyngier <maz@kernel.org>
The vGIC advertising code is unsurprisingly very much tied to
the GIC implementations. However, we are about to extend the
support to lesser implementations.
Let's dissociate the vgic registration from the GIC code and
move it into KVM, where it makes a bit more sense. This also
allows us to mark the gic_kvm_info structures as __initdata.
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210511125428.6108-2-thunder.leizhen@huawei.com
The Apple Interrupt Controller is only present on Apple Silicon SoCs.
Hence add a dependency on ARCH_APPLE, to prevent asking the user about
this driver when configuring a kernel without Apple Silicon SoC support.
Drop the default, as ARCH_APPLE already selects APPLE_AIC.
Fixes: 76cde26394 ("irqchip/apple-aic: Add support for the Apple Interrupt Controller")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/f37e8daea37d50651d2164b0b3dad90780188548.1618316398.git.geert+renesas@glider.be
- Stage-2 isolation for the host kernel when running in protected mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
x86:
- Optimizations and cleanup of nested SVM code
- AMD: Support for virtual SPEC_CTRL
- Optimizations of the new MMU code: fast invalidation,
zap under read lock, enable/disably dirty page logging under
read lock
- /dev/kvm API for AMD SEV live migration (guest API coming soon)
- support SEV virtual machines sharing the same encryption context
- support SGX in virtual machines
- add a few more statistics
- improved directed yield heuristics
- Lots and lots of cleanups
Generic:
- Rework of MMU notifier interface, simplifying and optimizing
the architecture-specific code
- Some selftests improvements
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmCJ13kUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroM1HAgAqzPxEtiTPTFeFJV5cnPPJ3dFoFDK
y/juZJUQ1AOtvuWzzwuf175ewkv9vfmtG6rVohpNSkUlJYeoc6tw7n8BTTzCVC1b
c/4Dnrjeycr6cskYlzaPyV6MSgjSv5gfyj1LA5UEM16LDyekmaynosVWY5wJhju+
Bnyid8l8Utgz+TLLYogfQJQECCrsU0Wm//n+8TWQgLf1uuiwshU5JJe7b43diJrY
+2DX+8p9yWXCTz62sCeDWNahUv8AbXpMeJ8uqZPYcN1P0gSEUGu8xKmLOFf9kR7b
M4U1Gyz8QQbjd2lqnwiWIkvRLX6gyGVbq2zH0QbhUe5gg3qGUX7JjrhdDQ==
=AXUi
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"This is a large update by KVM standards, including AMD PSP (Platform
Security Processor, aka "AMD Secure Technology") and ARM CoreSight
(debug and trace) changes.
ARM:
- CoreSight: Add support for ETE and TRBE
- Stage-2 isolation for the host kernel when running in protected
mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
x86:
- AMD PSP driver changes
- Optimizations and cleanup of nested SVM code
- AMD: Support for virtual SPEC_CTRL
- Optimizations of the new MMU code: fast invalidation, zap under
read lock, enable/disably dirty page logging under read lock
- /dev/kvm API for AMD SEV live migration (guest API coming soon)
- support SEV virtual machines sharing the same encryption context
- support SGX in virtual machines
- add a few more statistics
- improved directed yield heuristics
- Lots and lots of cleanups
Generic:
- Rework of MMU notifier interface, simplifying and optimizing the
architecture-specific code
- a handful of "Get rid of oprofile leftovers" patches
- Some selftests improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (379 commits)
KVM: selftests: Speed up set_memory_region_test
selftests: kvm: Fix the check of return value
KVM: x86: Take advantage of kvm_arch_dy_has_pending_interrupt()
KVM: SVM: Skip SEV cache flush if no ASIDs have been used
KVM: SVM: Remove an unnecessary prototype declaration of sev_flush_asids()
KVM: SVM: Drop redundant svm_sev_enabled() helper
KVM: SVM: Move SEV VMCB tracking allocation to sev.c
KVM: SVM: Explicitly check max SEV ASID during sev_hardware_setup()
KVM: SVM: Unconditionally invoke sev_hardware_teardown()
KVM: SVM: Enable SEV/SEV-ES functionality by default (when supported)
KVM: SVM: Condition sev_enabled and sev_es_enabled on CONFIG_KVM_AMD_SEV=y
KVM: SVM: Append "_enabled" to module-scoped SEV/SEV-ES control variables
KVM: SEV: Mask CPUID[0x8000001F].eax according to supported features
KVM: SVM: Move SEV module params/variables to sev.c
KVM: SVM: Disable SEV/SEV-ES if NPT is disabled
KVM: SVM: Free sev_asid_bitmap during init if SEV setup fails
KVM: SVM: Zero out the VMCB array used to track SEV ASID association
x86/sev: Drop redundant and potentially misleading 'sev_enabled'
KVM: x86: Move reverse CPUID helpers to separate header file
KVM: x86: Rename GPR accessors to make mode-aware variants the defaults
...
- removed broken/unmaintained MIPS KVM trap and emulate support
- added support for Loongson-2K1000
- fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=w/c4
-----END PGP SIGNATURE-----
Merge tag 'mips_5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- removed get_fs/set_fs
- removed broken/unmaintained MIPS KVM trap and emulate support
- added support for Loongson-2K1000
- fixes and cleanups
* tag 'mips_5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (107 commits)
MIPS: BCM63XX: Use BUG_ON instead of condition followed by BUG.
MIPS: select ARCH_KEEP_MEMBLOCK unconditionally
mips: Do not include hi and lo in clobber list for R6
MIPS:DTS:Correct the license for Loongson-2K
MIPS:DTS:Fix label name and interrupt number of ohci for Loongson-2K
MIPS: Avoid handcoded DIVU in `__div64_32' altogether
lib/math/test_div64: Correct the spelling of "dividend"
lib/math/test_div64: Fix error message formatting
mips/bootinfo:correct some comments of fw_arg
MIPS: Avoid DIVU in `__div64_32' is result would be zero
MIPS: Reinstate platform `__div64_32' handler
div64: Correct inline documentation for `do_div'
lib/math: Add a `do_div' test module
MIPS: Makefile: Replace -pg with CC_FLAGS_FTRACE
MIPS: pci-legacy: revert "use generic pci_enable_resources"
MIPS: Loongson64: Add kexec/kdump support
MIPS: pci-legacy: use generic pci_enable_resources
MIPS: pci-legacy: remove busn_resource field
MIPS: pci-legacy: remove redundant info messages
MIPS: pci-legacy: stop using of_pci_range_to_resource
...
The Apple M1 is the processor used it all current generation Apple
Macintosh computers. Support for this platform so far is rudimentary,
but it boots and can use framebuffer and serial console over a special
USB cable.
Support for several essential on-chip devices (USB, PCIe, IOMMU, NVMe)
is work in progress but was not ready in time.
A very detailed description of what works is in the merge commit
and on the AsahiLinux wiki.
Link: https://lore.kernel.org/linux-arm-kernel/bdb18e9f-fcd7-1e31-2224-19c0e5090706@marcan.st/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=pBZy
-----END PGP SIGNATURE-----
Merge tag 'arm-apple-m1-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM Apple M1 platform support from Arnd Bergmann:
"The Apple M1 is the processor used it all current generation Apple
Macintosh computers. Support for this platform so far is rudimentary,
but it boots and can use framebuffer and serial console over a special
USB cable.
Support for several essential on-chip devices (USB, PCIe, IOMMU, NVMe)
is work in progress but was not ready in time.
A very detailed description of what works is in the commit message of
commit 1bb2fd3880 ("Merge tag 'm1-soc-bringup-v5' [..]") and on the
AsahiLinux wiki"
Link: https://lore.kernel.org/linux-arm-kernel/bdb18e9f-fcd7-1e31-2224-19c0e5090706@marcan.st/
* tag 'arm-apple-m1-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
asm-generic/io.h: Unbork ioremap_np() declaration
arm64: apple: Add initial Apple Mac mini (M1, 2020) devicetree
dt-bindings: display: Add apple,simple-framebuffer
arm64: Kconfig: Introduce CONFIG_ARCH_APPLE
irqchip/apple-aic: Add support for the Apple Interrupt Controller
dt-bindings: interrupt-controller: Add DT bindings for apple-aic
arm64: Move ICH_ sysreg bits from arm-gic-v3.h to sysreg.h
of/address: Add infrastructure to declare MMIO as non-posted
asm-generic/io.h: implement pci_remap_cfgspace using ioremap_np
arm64: Implement ioremap_np() to map MMIO as nGnRnE
docs: driver-api: device-io: Document ioremap() variants & access funcs
docs: driver-api: device-io: Document I/O access functions
asm-generic/io.h: Add a non-posted variant of ioremap()
arm64: arch_timer: Implement support for interrupt-names
dt-bindings: timer: arm,arch_timer: Add interrupt-names support
arm64: cputype: Add CPU implementor & types for the Apple M1 cores
dt-bindings: arm: cpus: Add apple,firestorm & icestorm compatibles
dt-bindings: arm: apple: Add bindings for Apple ARM platforms
dt-bindings: vendor-prefixes: Add apple prefix
New HW support:
- New driver for the Nuvoton WPCM450 interrupt controller
- New driver for the IDT 79rc3243x interrupt controller
- Add support for interrupt trigger configuration to the MStar irqchip
- Add more external interrupt support to the STM32 irqchip
- Add new compatible strings for QCOM SC7280 to the qcom-pdc binding
Fixes and cleanups:
- Drop irq_create_strict_mappings() and irq_create_identity_mapping()
from the irqdomain API, with cleanups in a couple of drivers
- Fix nested NMI issue with spurious interrupts on GICv3
- Don't allow GICv4.1 vSGIs when the CPU doesn't support them
- Various cleanups and minor fixes
-----BEGIN PGP SIGNATURE-----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=RqVj
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip and irqdomain updates from Marc Zyngier:
New HW support:
- New driver for the Nuvoton WPCM450 interrupt controller
- New driver for the IDT 79rc3243x interrupt controller
- Add support for interrupt trigger configuration to the MStar irqchip
- Add more external interrupt support to the STM32 irqchip
- Add new compatible strings for QCOM SC7280 to the qcom-pdc binding
Fixes and cleanups:
- Drop irq_create_strict_mappings() and irq_create_identity_mapping()
from the irqdomain API, with cleanups in a couple of drivers
- Fix nested NMI issue with spurious interrupts on GICv3
- Don't allow GICv4.1 vSGIs when the CPU doesn't support them
- Various cleanups and minor fixes
Link: https://lore.kernel.org/r/20210424094640.1731920-1-maz@kernel.org
Previously the XILINX_INTC config option was hidden and only
auto-selected on the MicroBlaze platform. However, this IP can also be
used on the Zynq and ZynqMP platforms as a secondary cascaded
controller. Allow this option to be user-enabled on those platforms.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210423185853.2556087-1-robert.hancock@calian.com
IDT 79rc3243x SoCs have rather simple interrupt controllers connected
to the MIPS CPU interrupt lines. Each of them has room for up to
32 interrupts.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210422145330.73452-1-tsbogend@alpha.franken.de
GIC CPU interfaces versions predating GIC v4.1 were not built to
accommodate vINTID within the vSGI range; as reported in the GIC
specifications (8.2 "Changes to the CPU interface"), it is
CONSTRAINED UNPREDICTABLE to deliver a vSGI to a PE with
ID_AA64PFR0_EL1.GIC < b0011.
Check the GIC CPUIF version by reading the SYS_ID_AA64_PFR0_EL1.
Disable vSGIs if a CPUIF version < 4.1 is detected to prevent using
vSGIs on systems where they may misbehave.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210317100719.3331-2-lorenzo.pieralisi@arm.com
Use the 'fallthrough' macro to document that this switch case
does indeed fall through to the next case.
../drivers/irqchip/irq-tb10x.c: In function 'tb10x_irq_set_type':
../drivers/irqchip/irq-tb10x.c:62:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
62 | flow_type = IRQ_TYPE_LEVEL_LOW;
../drivers/irqchip/irq-tb10x.c:63:2: note: here
63 | case IRQ_TYPE_LEVEL_LOW:
| ^~~~
Fixes: b06eb0173e ("irqchip: Add TB10x interrupt controller driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210422051620.23021-1-rdunlap@infradead.org
This is the root interrupt controller used on Apple ARM SoCs such as the
M1. This irqchip driver performs multiple functions:
* Handles both IRQs and FIQs
* Drives the AIC peripheral itself (which handles IRQs)
* Dispatches FIQs to downstream hard-wired clients (currently the ARM
timer).
* Implements a virtual IPI multiplexer to funnel multiple Linux IPIs
into a single hardware IPI
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Hector Martin <marcan@marcan.st>
This driver is (for now) ARM specific, and currently doesn't
build with a variety of architectures (ia64, RISC-V, x86_64
at the very least).
Drop COMPILE_TEST from Kconfig until it gets sorted out.
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Support irq polarity configuration and save and restore the config
when system suspend and resume.
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
[maz: fixed irq_set_type callback]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210315131848.31840-1-mark-pk.tsai@mediatek.com
The WPCM450 AIC ("Advanced Interrupt Controller") is the interrupt
controller found in the Nuvoton WPCM450 SoC and other Winbond/Nuvoton
SoCs.
The list of registers if based on the AMI vendor kernel and the
Nuvoton W90N745 datasheet.
Although the hardware supports other interrupt modes, the driver only
supports high-level interrupts at the moment, because other modes could
not be tested so far.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210406120921.2484986-7-j.neuschaefer@gmx.net
Add following usart instances exti direct event support (used for UART wake
up).
- exti 26 (USART1) is mapped to GIC 37
- exti 27 (USART2) is mapped to GIC 38
- exti 28 (USART3) is mapped to GIC 39
- exti 29 (USART6) is mapped to GIC 71
- exti 31 (UART5) is mapped to GIC 53
- exti 32 (UART7) is mapped to GIC 82
- exti 33 (UART8) is mapped to GIC 83
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210319184253.5841-4-erwan.leray@foss.st.com
When building with extra warnings enabled, clang points out a
mistake in the error handling:
drivers/irqchip/irq-gic-v3-mbi.c:306:21: error: result of comparison of constant 18446744073709551615 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (mbi_phys_base == OF_BAD_ADDR) {
Truncate the constant to the same type as the variable it gets compared
to, to shut make the check work and void the warning.
Fixes: 505287525c ("irqchip/gic-v3: Add support for Message Based Interrupts as an MSI controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210323131842.2773094-1-arnd@kernel.org
All of these two are never modified after init, so they can be
__ro_after_init.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210330020911.26423e9e@xhacker
Add IO interrupt controller support for Loongson-2K1000, different
from the Loongson-3A series is that Loongson-2K1000 has 64 interrupt
sources, 0-31 correspond to the device tree liointc0 device node, and
the other correspond to liointc1 node.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Qing Zhang <zhangqing@loongson.cn>
Tested-by: Ming Wang <wangming01@loongson.cn>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
GICv4.1 gives a way to get the VLPI state, which needs to map the
vPE first, and after the state read, we may remap the vPE back while
the VPT is not empty. So we can't assume that the VPT is empty at
the first map. Besides, the optimization of PTZ is probably limited
since the HW should be fairly efficient to parse the empty VPT. Let's
drop the setting of PTZ altogether.
Signed-off-by: Shenming Lu <lushenming@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210322060158.1584-3-lushenming@huawei.com
In order to be able to manipulate the VPT once a vPE has been
unmapped, perform the required CMO to invalidate the CPU view
of the VPT.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Shenming Lu <lushenming@huawei.com>
Link: https://lore.kernel.org/r/20210322060158.1584-2-lushenming@huawei.com
The purpose of separating loongson_system_configuration from boot_param.h
is to keep the other structure consistent with the firmware.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Qing Zhang <zhangqing@loongson.cn>
Acked-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add support for the interrupt controller found in the JZ4760 SoC, which
works exactly like the one in the JZ4770.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210307172014.73481-2-paul@crapouillou.net
Implementing CONFIG_GENERIC_IRQ_MULTI_HANDLER is a decision that is
made at the architecture level, and shouldn't involve the irqchip
at all (we even provide a fallback helper when the option isn't
selected).
Drop all instances of such selection from non-arch code.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210217142800.2547737-1-maz@kernel.org
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Hector Martin <marcan@marcan.st>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
- New driver for the MIPS-based Realtek RTL838x/RTL839x SoC
- Conversion of the sun6i-r support code to a hierarchical setup
- Fix wake-up interrupts for the ls-extirq driver
- Fix MSI allocation for the loongson-pch-msi driver
- Add compatible strings for new Qualcomm SoCs
- Tidy up a few Kconfig entries (IMX, CSKY)
- Spelling phyksiz
- Remove the sirfsoc and tango drivers
-----BEGIN PGP SIGNATURE-----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=hhRV
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier
- New driver for the MIPS-based Realtek RTL838x/RTL839x SoC
- Conversion of the sun6i-r support code to a hierarchical setup
- Fix wake-up interrupts for the ls-extirq driver
- Fix MSI allocation for the loongson-pch-msi driver
- Add compatible strings for new Qualcomm SoCs
- Tidy up a few Kconfig entries (IMX, CSKY)
- Spelling phyksiz
- Remove the sirfsoc and tango drivers
Link: https://lore.kernel.org/r/20210214124015.3333457-1-maz@kernel.org
Merely enabling CONFIG_COMPILE_TEST should not enable additional code.
To fix this, restrict the automatic enabling of IMX_INTMUX to ARCH_MXC,
and ask the user in case of compile-testing.
Fixes: 66968d7dfc ("irqchip: Add COMPILE_TEST support for IMX_INTMUX")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210208145605.422943-1-geert+renesas@glider.be
Currently we use bitmap_alloc() to allocate msi bitmap which should be
initialized with zero. This is obviously wrong but it works because msi
can fallback to legacy interrupt mode. So use bitmap_zalloc() instead.
Fixes: 632dcc2c75 ("irqchip: Add Loongson PCH MSI controller")
Cc: stable@vger.kernel.org
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210209071051.2078435-1-chenhuacai@loongson.cn
The irq-csky-mpintc driver is only supported on CPU_CK860 and
it will generate a compilation error when selected with CPU_CK610.
As it is already selected directly in the architecture Kconfig,
drop the option to select it manually.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
[maz: rewrote commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210204074609.3553018-1-guoren@kernel.org
This is a standard IRQ driver with only status and mask registers.
The mapping from SoC interrupts (18-31) to MIPS core interrupts is
done via an interrupt-map in device tree.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210122204224.509124-3-bert@biot.com
The ls-extirq driver doesn't implement the irq_set_wake()
callback, while being wake-up capable. This results in
ugly behaviours across suspend/resume cycles.
Advertise this by adding IRQCHIP_SKIP_SET_WAKE to
the irqchip flags
Fixes: b16a1caf46 ("irqchip/ls-extirq: Add LS1043A, LS1088A external interrupt support")
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210129095034.33821-1-biwen.li@oss.nxp.com
Maintain bitmaps of wake-enabled IRQs and mux inputs, and program them
to the hardware during the syscore phase of suspend and shutdown. Then
restore the original set of enabled IRQs (only the NMI) during resume.
This serves two purposes. First, it lets power management firmware
running on the ARISC coprocessor know which wakeup sources Linux wants
to have enabled. That way, it can avoid turning them off when it shuts
down the remainder of the clock tree. Second, it preconfigures the
coprocessor's interrupt controller, so the firmware's wakeup logic
is as simple as waiting for an interrupt to arrive.
The suspend/resume logic is not conditional on PM_SLEEP because it is
identical to the init/shutdown logic. Wake IRQs may be enabled during
shutdown to allow powering the board back on. As an example, see
commit a5c5e50cce ("Input: gpio-keys - add shutdown callback").
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210118055040.21910-5-samuel@sholland.org
The R_INTC in the A31 and newer sun8i/sun50i SoCs is more similar to the
original sun4i interrupt controller than the sun7i/sun9i NMI controller.
It is used for two distinct purposes:
- To control the trigger, latch, and mask for the NMI input pin
- To provide the interrupt input for the ARISC coprocessor
As this interrupt controller is not documented, information about it
comes from vendor-provided firmware blobs and from experimentation.
Differences from the sun4i interrupt controller appear to be:
- It only has one or two registers of each kind (max 32 or 64 IRQs)
- Multiplexing logic is added to support additional inputs
- There is no FIQ-related logic
- There is no interrupt priority logic
In order to fulfill its two purposes, this hardware block combines four
types of IRQs. First, the NMI pin is routed to the "IRQ 0" input on this
chip, with a trigger type controlled by the NMI_CTRL_REG. The "IRQ 0
pending" output from this chip, if enabled, is then routed to a SPI IRQ
input on the GIC. In other words, bit 0 of IRQ_ENABLE_REG *does* affect
the NMI IRQ seen at the GIC.
The NMI is followed by a contiguous block of 15 "direct" (my name for
them) IRQ inputs that are connected in parallel to both R_INTC and the
GIC. Or in other words, these bits of IRQ_ENABLE_REG *do not* affect the
IRQs seen at the GIC.
Following the direct IRQs are the ARISC's copy of banked IRQs for shared
peripherals. These are not relevant to Linux. The remaining IRQs are
connected to a multiplexer and provide access to the first (up to) 128
SPIs from the ARISC. This range of SPIs overlaps with the direct IRQs.
Because of the 1:1 correspondence between R_INTC and GIC inputs, this is
a perfect scenario for using a stacked irqchip driver. We want to hook
into setting the NMI trigger type, but not actually handle any IRQ here.
To allow access to all multiplexed IRQs, this driver requires a new
binding where the interrupt number matches the GIC interrupt number.
(This moves the NMI from number 0 to 32 or 96, depending on the SoC.)
For simplicity, copy the three-cell GIC binding; this disambiguates
interrupt 0 in the old binding (the NMI) from interrupt 0 in the new
binding (SPI 0) by the number of cells.
Since R_INTC is in the always-on power domain, and its output is visible
to the power management coprocessor, a stacked irqchip driver provides a
simple way to add wakeup support to any of its IRQs. That is the next
patch; for now, just the NMI is moved over.
This commit mostly reverts commit 173bda53b3 ("irqchip/sunxi-nmi:
Support sun6i-a31-r-intc compatible").
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210118055040.21910-4-samuel@sholland.org
The GICv3 driver explanation related to PMR/RPR and SCR_EL3.FIQ
secure/non-secure priority handling contains a couple of typos.
Fix them.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210121182252.29320-1-lorenzo.pieralisi@arm.com
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <baohua@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210120133008.2421897-3-arnd@kernel.org
The tango platform is getting removed, so the driver is no
longer needed.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210120133008.2421897-2-arnd@kernel.org
Antonio Borneo
Loic Pallardy
Ludovic Barre
Samuel Holland
Lad Prabhakar
Wei Yongjun
Jamie Iles
Stafford Horne
Robin Murphy
Sai Prakash Ranjan
Thomas Gleixner
Jiaxun Yang
Kunihiko Hayashi
Miaoqian Lin
Huacai Chen
Linus Torvalds
Marc Zyngier
Mark Rutland
Pali Rohár
Florian Fainelli
Haowen Bai
Lucas Stach
Nathan Rossi
Krzysztof Kozlowski
Max Filippov
Daniel Thompson
Linus Walleij
Yury Norov
Andre Przywara
Yang Yingliang
YueHaibing
Arnd Bergmann
Shawn Guo
Hector Martin
Qianggui Song
Alan Kao
Michal Simek
Niklas Cassel
Souptick Joarder (HPE)
Christoph Hellwig
Barry Song
Alexandre Torgue
Guo Ren
Ard Biesheuvel
Christophe JAILLET
Sander Vanheule
Kees Cook
Xiang wangx
Peng Fan
Herve Codina
Valentin Schneider
Ye Guojin
Wudi Wang
Donghyeok Kim
Vladimir Murzin
Geert Uytterhoeven
Billy Tsai
Claudiu Beznea
Neil Armstrong
Cai Huoqing
Kaige Fu
Randy Dunlap
Chen-Yu Tsai
Sven Peter
Markus Schneider-Pargmann
James Morse
Andy Shevchenko
Chunfeng Yun
Zhen Lei
Saravana Kannan
Robert Hancock
He Ying
Thomas Bogendoerfer
Lorenzo Pieralisi
Mark-PK Tsai
Jonathan Neuschäfer
Erwan Le Ray
Jisheng Zhang
Hao Fang
Qing Zhang
Shenming Lu
Ingo Molnar
Paul Cercueil
Bert Vermeulen
Biwen Li