Instead of open-coding irqchip handling in the driver we can take advantage
of the new irqchip helpers provided by the gpiolib core.
While doing this we also make sure that we call gpiochip_irqchip_add()
after the gpiochip itself is registered as required.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for GPIO controller used by Xilinx Zynq.
v3 changes:
- Use linux/gpio/driver.h instead of linux/gpio.h
- Make irq a local variable in probe
v2 changes:
- convert to pm_runtime_force_(suspend|resume)
- add pm_runtime_set_active in probe()
- also (un)prepare clocks when they are dis-/enabled
- add some missing calls to pm_runtime_get()
- use pm_runtime_put() instead of sync variant
- remove gpio chip in driver remove()
- remove redundant type casts
- directly use IO helpers
- use BIT macro to set/clear bits
- migrate to GPIOLIB_IRQCHIP
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the STMPE driver to use the gpiolib irqchip
helpers.
Tested-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Devices based on Intel SoC products such as Baytrail have a Power
Management IC. In the PMIC there are subsystems for voltage regulation,
A/D conversion, GPIO and PWMs. The PMIC in Baytrail-T platform is
called Crystal Cove.
This patch adds support for the GPIO function in Crystal Cove.
Signed-off-by: Yang, Bin <bin.yang@intel.com>
Signed-off-by: Zhu, Lejun <lejun.zhu@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These helpers depend on the IRQ_DOMAIN so select it explicitly,
as it will not be present on all platforms such as Intel
desktops and laptops using Intel-MID.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the PCA953x driver over to using the gpiolib irqchip
helpers to handle the threaded interrups cascaded off this
GPIO chip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Renesas R-Car GPIO driver is only useful on shmobile unless build
testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Magnus Damm <damm@opensource.se>
Cc: Alexandre Courbot <gnurou@gmail.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio-pch driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 4df42de9d3e "gpio: omap: add a GPIO_OMAP option instead of using
ARCH_OMAP" made it possible to build OMAP kernels without the GPIO driver,
which at least on OMAP2 and OMAP3 causes build errors because of functions
used by the platform power management code:
arch/arm/mach-omap2/built-in.o: In function `omap_sram_idle':
arch/arm/mach-omap2/pm24xx.c:129: undefined reference to `omap2_gpio_prepare_for_idle'
arch/arm/mach-omap2/pm24xx.c:129: undefined reference to `omap2_gpio_resume_after_idle'
We presumably always want the GPIO driver on OMAP, so this adds a slightly
broader dependency and only allows disabling the driver only when no
OMAP2PLUS platform is selected.
However, it seems entirely reasonable to include the driver in build tests
on other platforms, so we should also allow building it for COMPILE_TEST
builds and select the required GENERIC_IRQ_CHIP that may not already be
enabled on other platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Converts the GPIO OMAP driver to register its chained irq
handler and irqchip using the helpers in the gpiolib core.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ARCH_OMAP config option was used to built the GPIO OMAP
driver but this is not consistent with the rest of the GPIO
drivers that have their own Kconfig option.
Also, this make it harder to add dependencies or reverse
dependencies (i.e: select) since that would mean touching the
sub-arch config option.
So is better to add a boolean Kconfig option for this driver
that defaults to true if ARCH_OMAP is enabled.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO_TIMBERDALE doesn't need an explicit dependency on HAS_IOMEM,
because it depends on MFD_TIMBERDALE which itself depends on
HAS_IOMEM already.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that the gpiolib irqchip helpers can support nested, threaded
IRQ handlers, switch the TC3589x driver over to using this new
infrastructure. Tested on the Ux500.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask
us to pick up the changes to avoid conflicts. A large chunk of this
are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
that, reset controllers for STi as well as a large rework of the
Marvell Orion/EBU watchdog driver are notable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u/FI
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
This converts the PL061 driver to register its chained irq
handler and irqchip using the helpers in the gpiolib core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This provides a function gpiochip_irqchip_add() to set
up an irqchip for a GPIO controller, and a function
gpiochip_set_chained_irqchip() to chain it to a parent
irqchip.
Most GPIOs are of the type where a number of lines form
a cascaded interrupt controller chained onto
the primary system interrupt controller (or further down the
chain) so let's add this helper and factor the code to
request the lines to be used as IRQs, the .to_irq() function
and the irqdomain into the core as well.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SYSCON driver was designed for using memory areas (registers)
that are used in several subsystems. There are systems (CPUs)
which use bits in one register for various purposes and thus
should be handled by various kernel subsystems. This driver
allows you to use the individual SYSCON bits as GPIOs.
ARM CLPS711X SYSFLG1 input lines has been added as first user
of this driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bus and architecture dependencies are already on MFD_CS5535, so
there is no need to repeat them here.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
fix build error with this message:
kernel/irq/Kconfig:41:error: recursive dependency detected!
kernel/irq/Kconfig:41: symbol GENERIC_IRQ_CHIP is selected by GPIO_DWAPB
drivers/gpio/Kconfig:131: symbol GPIO_DWAPB depends on IRQ_DOMAIN
kernel/irq/Kconfig:46: symbol IRQ_DOMAIN is selected by GENERIC_IRQ_CHIP
Signed-off-by: Alan Tull <atull@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of just depending on OF and getting build failures,
depend on ARM && OF_GPIO.
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Synopsys DesignWare block is used in some ARM devices (picoxcell)
and can be configured to provide multiple banks of GPIO pins.
v12: - Add irq_startup/shutdown
- do irq_create_mapping() in probe, irq_find_mapping() in to_irq()
- Adjust mappings to show support for 1 gpio per port.
- gpio-cells = <1>
v11: - Use NULL when checking existence of 'interrupts' property
- Bindings descriptions cleanup
v10: - in documentation nr-gpio -> nr-gpios
v9: - cleanup in dt bindings doc
- use of_get_child_count()
v8: - remove socfpga.dtsi changes
- minor cleanup in devicetree documentation
v7: - use irq_generic_chip
- support one irq per gpio line or one irq for many
- s/bank/port/ and other cleanup
v6: - (atull) squash the set of patches
- use linear irq domain
- build fixes. Original driver was reviewed on v3.2.
- Fix setting irq edge type for 'rising' and 'both'.
- Support as a loadable module.
- Use bgpio_chip's spinlock during register access.
- Clean up register names to match spec
- s/bank/port/ because register names use the word 'port'
- s/nr-gpio/nr-gpios/
- don't get/put the of_node
- remove signoffs/acked-by's because of changes
- other cleanup
v5: - handle sparse bank population correctly
v3: - depend on rather than select IRQ_DOMAIN
- split IRQ support into a separate patch
v2: - use Rob Herring's irqdomain in generic irq chip patches
- use reg property to indicate bank index
- support irqs on both edges based on LinusW's u300 driver
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Alan Tull <atull@altera.com>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver supports the GPIO controller found in LSI ZEVIO SoCs.
It has been successfully tested on a TI nspire CX calculator.
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no point in displaying the TS5500-specific driver entries if
TS5500 board support itself isn't enabled.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Merge "qcom driver changes for v3.15" from Kumar Gala:
We've split Qualcomm MSM support into legacy and multiplatform. These
drivers are only relevant on the multiplatform supported SoCs so switch the
Kconfig depends to ARCH_QCOM.
* tag 'qcom-drivers-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
gpio: msm: switch Kconfig to ARCH_QCOM depends
hwrng: msm: switch Kconfig to ARCH_QCOM depends
power: reset: msm - switch Kconfig to ARCH_QCOM depends
drm/msm: drop ARCH_MSM Kconfig depend
tty: serial: msm: Enable building msm_serial for ARCH_QCOM
We've split Qualcomm MSM support into legacy and multiplatform. The gpio
msm-v2 driver is only relevant on the multiplatform supported SoCs so
switch the Kconfig depends to ARCH_QCOM.
CC: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add the NXP PCA9698 40-bit GPIO expander to the supported list.
Note: This only enables GPIO functionality.
Tested-by: Bob Schmitz <bschmitz@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Graeme Smecher <gsmecher@threespeedlogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pca953x driver supports tca6424 (24-bit) and pca9505 (40-bit)
devices. They were the only supported devices not mentioned in the
Kconfig help.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Graeme Smecher <gsmecher@threespeedlogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit f1f70479e9 "gpio: pl061: support irqdomain" drops the support of
irq generic chip and use irqdomain instead. Thus fixes the dependency by
selecting IRQ_DOMAIN rather than GENERIC_IRQ_CHIP.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio-tb10x driver uses generic irq chip APIs (irq_alloc_domain_generic_chips,
irq_remove_generic_chip), so it needs to select GENERIC_IRQ_CHIP to avoid build
error.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et. al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL' removal,
unused uninitialised warning mitigation, error message clarity,
removal of redundant/duplicate checks, licensing (GPL -> GPL2),
coding consistency, duplicate function declaration, ret checks,
commit corrections, redundant of_match_ptr() helper removal,
spelling, #if-deffery removal and header guards name changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=PuTE
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd
Pull MFD changes from Lee Jones:
"New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and
Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM
Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et.al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL'
removal, unused uninitialised warning mitigation, error
message clarity, removal of redundant/duplicate checks,
licensing (GPL -> GPL2), coding consistency, duplicate
function declaration, ret checks, commit corrections,
redundant of_match_ptr() helper removal, spelling,
#if-deffery removal and header guards name changes"
* tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd: (78 commits)
mfd: wm5110: Add register patch for rev D chip
mfd: omap-usb-tll: Don't hold lock during pm_runtime_get/put_sync()
gpio: lp3943: Remove redundant of_match_ptr helper
mfd: sta2x11-mfd: Use named constants for pci_power_t values
Documentation: mfd: Fix LDO index in s2mps11.txt
mfd: Cleanup mfd-mcp-sa11x0.h header
mfd: max8997: Use "IS_ENABLED(CONFIG_OF)" for DT code.
mfd: twl6030: Fix endianness problem in IRQ handler
mfd: sec-core: Add cells for S5M8767-clocks
mfd: max14577: Remove redundant of_match_ptr helper
mfd: twl6040: Fix sparse non static symbol warning
mfd: Revert "mfd: Always assign of_node in mfd_add_device()"
mfd: rtsx: Fix sparse non static symbol warning
mfd: max77693: Set proper maximum register for MUIC regmap
mfd: max77686: Fix regmap resource leak on driver remove
mfd: Represent correct filenames in file headers
mfd: rtsx: Add support for card reader rtl8402
mfd: rtsx: Add set pull control macro and simplify rtl8411
mfd: max8997: Enforce mfd_add_devices() return value check
mfd: mc13xxx: Simplify probe() & remove()
...
A big set this merge window, as we have much going on in
this subsystem. Major changes this time:
- Some core improvements and cleanups to the new GPIO
descriptor API. This seems to be working now so we can
start the exodus to this API, moving gradually away from
the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move
the few GPIO ACPI clients we have to the GPIO descriptor
API right *now* before we go any further. We actually
managed to contain this *before* we started to litter
the kernel with yet another hackish global numberspace for
the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have
been migrated to use the GPIO descriptors rather than
fixed number assignments. Tegra machine has been migrated
as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x.
Those should be really good examples of how I expect a
nice GPIO driver to look these days.
- Do away with custom GPIO implementations on a major
part of the ARM machines: ks8695, lpc32xx, mv78xx0.
Make a first step towards the same in the horribly
convoluted Samsung S3C include forest. We expect to
continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em,
intel-mid and lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line
is used for IRQs and can then enforce some semantics such
as disallowing a GPIO line marked as in use for IRQ to be
switched to output mode.
- Drop all use of irq_set_chip_and_handler_name().
The name provided in these cases were just unhelpful
tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em
74x164 and msm drivers.
- Some non-urgent bug fixes here and there, duplicate
#includes and that usual kind of cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lW2i
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO tree bulk changes from Linus Walleij:
"A big set this merge window, as we have much going on in this
subsystem. The changes to other subsystems (notably a slew of ARM
machines as I am doing away with their custom APIs) have all been
ACKed to the extent possible.
Major changes this time:
- Some core improvements and cleanups to the new GPIO descriptor API.
This seems to be working now so we can start the exodus to this
API, moving gradually away from the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move the few
GPIO ACPI clients we have to the GPIO descriptor API right *now*
before we go any further. We actually managed to contain this
*before* we started to litter the kernel with yet another hackish
global numberspace for the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have been
migrated to use the GPIO descriptors rather than fixed number
assignments. Tegra machine has been migrated as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x. Those
should be really good examples of how I expect a nice GPIO driver
to look these days.
- Do away with custom GPIO implementations on a major part of the ARM
machines: ks8695, lpc32xx, mv78xx0. Make a first step towards the
same in the horribly convoluted Samsung S3C include forest. We
expect to continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em, intel-mid and
lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line is used
for IRQs and can then enforce some semantics such as disallowing a
GPIO line marked as in use for IRQ to be switched to output mode.
- Drop all use of irq_set_chip_and_handler_name(). The name provided
in these cases were just unhelpful tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em 74x164 and
msm drivers.
- Some non-urgent bug fixes here and there, duplicate #includes and
that usual kind of cleanups"
Fix up broken Kconfig file manually to make this all compile.
* tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: mcp23s08: fix casting caused build warning
gpio: mcp23s08: depend on OF_GPIO
gpio: mcp23s08: Add irq functionality for i2c chips
ARM: S5P[v210|c100|64x0]: Fix build error
gpio: pxa: clamp gpio get value to [0,1]
ARM: s3c24xx: explicit dependency on <plat/gpio-cfg.h>
ARM: S3C[24|64]xx: move includes back under <mach/> scope
Documentation / ACPI: update to GPIO descriptor API
gpio / ACPI: get rid of acpi_gpio.h
gpio / ACPI: register to ACPI events automatically
mmc: sdhci-acpi: convert to use GPIO descriptor API
ARM: s3c24xx: fix build error
gpio: f7188x: set can_sleep attribute
gpio: samsung: Update documentation
gpio: samsung: Remove hardware.h inclusion
gpio: xtensa: depend on HAVE_XTENSA_GPIO32
gpio: clps711x: Enable driver compilation with COMPILE_TEST
gpio: clps711x: Use of_match_ptr()
net: rfkill: gpio: convert to descriptor-based GPIO interface
leds: s3c24xx: Fix build failure
...
This is one of LP3943 MFD driver.
LP3943 is configurable as a GPIO expander, up to 16 GPIOs.
* Application note: how to configure LP3943 as a GPIO expander
http://www.ti.com/lit/an/snva287a/snva287a.pdf
* Supported GPIO controller operations
request, free, direction_input, direction_output, get and set
* GPIO direction register not supported
LP3943 doesn't have the GPIO direction register. It only provides input and
output status registers.
So, private data for the direction should be handled manually.
This variable is updated whenever the direction is changed and
used in 'get' operation.
* Pin assignment
A driver data, 'pin_used' is checked when a GPIO is requested.
If the GPIO is already assigned, then returns as failure.
If the GPIO is available, 'pin_used' is set.
When the GPIO is not used anymore, then it is cleared.
It is defined as unsigned long type for atomic bit operation APIs,
but only LSB 16bits are used because LP3943 has 16 outputs.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MCP drivers fails to compile on trial builds due to missing
Kconfig dependency on OF_GPIO. Fix it.
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds interrupt functionality for i2c chips to the driver.
They can act as a interrupt-controller and generate interrupts, if
the inputs change.
This is tested with a mcp23017 chip on an arm based platform.
v3:
- be a bit more clear that the irq functionality is also available
on spi versions of the chips, but the linux driver does not support
this yet
v2:
- some more word about irq-mirror property in binding doc
- use of_read_bool instead of of_find_property for
"interrupt-contrller" and "irq-mirror"
- cache the "interrupt-controller" for remove function
- do set the irq-mirror bit only if device is marked as
interrupt-controller
- do create the irq mapping and setup of irq_desc of all possible
interrupts in probe path instead of in gpio_to_irq
- mark gpios as in use as interrupts in irq in irq_startup and
unlock it in irq_shutdown
- rename virq to child_irq
- remove dev argument from mcp23s08_irq_setup function
- move gpiochip_add before mcp23s08_irq_setup in probe path
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Prevent build failure when the selected variant does not support GPIO32.
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The compatible to Davinci GPIO HW block is used by other TI SoCs, like
Keystone, where GPIO support is declared as optional.
Hence, introduce GPIO_DAVINCI Kconfig option which will allow to enable
Davinci GPIO driver for Keystone SoCs when needed. At same time, kept
Davinci GPIO driver enabled for Davinci SoCs by default.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch adds support for the GPIOs found on the SMSC "Super I/
SCH311x.
The chip detection and I/O functions are copied from sch311x_wdt.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO32 is a standard optional extension to the Xtensa architecture
core that provides preconfigured output and input ports for intra
SoC signaling. The GPIO32 option is implemented as 32bit Tensilica
Instruction Extension (TIE) output state called EXPSTATE, and 32bit
input wire called IMPWIRE. This driver treats input and output
states as two distinct devices.
v3:
* Use BUG() in xtensa_impwire_set_value() to indicate that
it should never be called (Linus Walleij)
v2:
* Address the comments of Linus Walleij:
- Add a few comments
- Expand commit log message
- Use the BIT() macro for bit offsets
- Rewrite CPENABLE handling as static inlines
- Use device_initcall()
* Depend on !SMP for reason explained in the comments (Marc Gauthier)
* Use XCHAL_CP_ID_XTIOP to enable/disable GPIO32 only
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 20bc4d5d56
(gpio: 74x164: Add support for the daisy-chaining) introduce check
for DT for the driver, so driver cannot be used without DT.
There are no in-tree users of this driver, so remove non-DT support
completely.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Change CONFIG_GPIO_LYNXPOINT from bool to tristate so that the
gpio-lynxpoint driver can be built as a module.
Add the required glue: an exit function to unregister the driver, and
module information.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Merged the GPIO descriptor API from Alexandre Courbot.
This is a first step toward trying to get rid of the
global GPIO numberspace for the future.
- Add an API so that driver can flag that a certain GPIO
line is being used by a irqchip backend for generating
IRQs, so that we can enforce checks, like not allowing
users to switch that line to an output at runtime, since
this makes no sense. Implemented corresponding calls
in a few select drivers.
- ACPI GPIO cleanups, refactorings and switch to using the
descriptor-based interface.
- Support for the TPS80036 Palmas GPIO variant.
- A new driver for the Broadcom Kona GPIO SoC IP block.
- Device tree support for the PCF857x driver.
- A set of ARM GPIO refactorings with the goal of getting
rid of a bunch of custom GPIO implementations from the
arch/arm/* tree:
- Move the IOP GPIO driver to the GPIO subsystem and
fix all users to use the gpiolib API for accessing
GPIOs. Delete the old custom GPIO implementation.
- Delete the unused custom PXA GPIO implemention.
- Convert all users of the IXP4 custom GPIO
implementation to use gpiolib and delete the custom
implementation.
- Delete the custom Gemini GPIO implementation, also
completely unused.
- Various cleanups and renamings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=881E
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"Here is the bulk of GPIO changes for the v3.13 development cycle.
I've got ACKs for the things that affect other subsystems (or it's my
own subsystem, like pinctrl). Most of that pertain to an attempt from
my side to consolidate and get rid of custom GPIO implementations in
the ARM tree. I will continue doing this.
The main change this time is the new GPIO descriptor API, background
for this can be found in Corbet's summary from this january in LWN:
http://lwn.net/Articles/533632/
Summary:
- Merged the GPIO descriptor API from Alexandre Courbot. This is a
first step toward trying to get rid of the global GPIO numberspace
for the future.
- Add an API so that driver can flag that a certain GPIO line is
being used by a irqchip backend for generating IRQs, so that we can
enforce checks, like not allowing users to switch that line to an
output at runtime, since this makes no sense. Implemented
corresponding calls in a few select drivers.
- ACPI GPIO cleanups, refactorings and switch to using the
descriptor-based interface.
- Support for the TPS80036 Palmas GPIO variant.
- A new driver for the Broadcom Kona GPIO SoC IP block.
- Device tree support for the PCF857x driver.
- A set of ARM GPIO refactorings with the goal of getting rid of a
bunch of custom GPIO implementations from the arch/arm/* tree:
* Move the IOP GPIO driver to the GPIO subsystem and fix all users
to use the gpiolib API for accessing GPIOs. Delete the old
custom GPIO implementation.
* Delete the unused custom PXA GPIO implemention.
* Convert all users of the IXP4 custom GPIO implementation to use
gpiolib and delete the custom implementation.
* Delete the custom Gemini GPIO implementation, also completely
unused.
- Various cleanups and renamings"
* tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: gpio-mxs: Remove unneeded dt checks
gpio: pl061: don't depend on CONFIG_ARM
gpio: bcm-kona: add missing .owner to struct gpio_chip
gpiolib: provide a declaration of seq_file in gpio/driver.h
gpiolib: include gpio/consumer.h in of_gpio.h for desc_to_gpio()
gpio: provide stubs for devres gpio functions
gpiolib: devres: add missing headers
gpiolib: make GPIO_DEVRES depend on GPIOLIB
gpiolib: devres: fix devm_gpiod_get_index()
gpiolib / ACPI: document the GPIO descriptor based interface
gpiolib / ACPI: allow passing GPIOF_ACTIVE_LOW for GpioInt resources
gpiolib / ACPI: add ACPI support for gpiod_get_index()
gpiolib / ACPI: convert to gpiod interfaces
gpiolib: add gpiod_get() and gpiod_put() functions
gpiolib: port of_ functions to use gpiod
gpiolib: export descriptor-based GPIO interface
Fixup "MAINTAINERS: GPIO-INTEL-MID: add maintainer"
gpio: bcm281xx: Don't print addresses of GPIO area in probe()
gpio: tegra: use new gpio_lock_as_irq() API
gpio: rcar: Include linux/of.h header
...
The pl061 driver has no real dependency on ARM, so remove the kconfig
dependency.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current Kconfig allows GPIO_DEVRES to be selected and compiled without
GPIOLIB. This does not make sense anymore since GPIOLIB has become the
exclusive way to deal with GPIOs. This patch makes GPIO_DEVRES available
only if GPIOLIB is selected.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO driver for the Abilis Systems TB10x series of SOCs based on ARC700
CPUs. It supports GPIO control and GPIO interrupt generation. This driver
works in conjunction with the TB10x pinctrl driver.
Signed-off-by: Sascha Leuenberger <sascha.leuenberger@abilis.com>
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio-langwell is a deprecated name. Despite the driver was made
initially for Langwell, it supports now other Intel Mid SoC's.
This patch does no change beside the file renaming with Kconfig/Makefile
update.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the IOP GPIO driver to live with its siblings in the
GPIO subsystem.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the recent code cleanup from Marek Vasut, driver gpio-ucb1400 can
be built as a module, so change symbol GPIO_UCB1400 from bool to
tristate.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the GPIO driver for the Broadcom bcm281xx family of mobile SoCs.
These GPIO controllers may contain up to 8 banks where each bank
includes 32 pins that can be driven high or low and act as an edge
sensitive interrupt.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
[Added depends on OF_GPIO]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
EMEV2 is now a DT platform, however the GPIO driver cannot be used
from a DT file since it does not fill out the of_node field in its
gpio_chip structure.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull MIPS updates from Ralf Baechle:
"This has been sitting in -next for a while with no objections and all
MIPS defconfigs except one are building fine; that one platform got
broken by another patch in your tree and I'm going to submit a patch
separately.
- a handful of fixes that didn't make 3.11
- a few bits of Octeon 3 support with more to come for a later
release
- platform enhancements for Octeon, ath79, Lantiq, Netlogic and
Ralink SOCs
- a GPIO driver for the Octeon
- some dusting off of the DECstation code
- the usual dose of cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (65 commits)
MIPS: DMA: Fix BUG due to smp_processor_id() in preemptible code
MIPS: kexec: Fix random crashes while loading crashkernel
MIPS: kdump: Skip walking indirection page for crashkernels
MIPS: DECstation HRT calibration bug fixes
MIPS: Export copy_from_user_page() (needed by lustre)
MIPS: Add driver for the built-in PCI controller of the RT3883 SoC
MIPS: DMA: For BMIPS5000 cores flush region just like non-coherent R10000
MIPS: ralink: Add support for reset-controller API
MIPS: ralink: mt7620: Add cpu-feature-override header
MIPS: ralink: mt7620: Add spi clock definition
MIPS: ralink: mt7620: Add wdt clock definition
MIPS: ralink: mt7620: Improve clock frequency detection
MIPS: ralink: mt7620: This SoC has EHCI and OHCI hosts
MIPS: ralink: mt7620: Add verbose ram info
MIPS: ralink: Probe clocksources from OF
MIPS: ralink: Add support for systick timer found on newer ralink SoC
MIPS: ralink: Add support for periodic timer irq
MIPS: Netlogic: Built-in DTB for XLP2xx SoC boards
MIPS: Netlogic: Add support for USB on XLP2xx
MIPS: Netlogic: XLP2xx update for I2C controller
...
This patch adds support for the GPIOs found on the Fintek super-I/O
chips F71882FG and F71889F.
A super-I/O is a legacy I/O controller embedded on x86 motherboards. It
is used to connect the low-bandwidth devices. Among others functions the
F71882FG/F71889F provides: a parallel port, two serial ports, a keyboard
controller, an hardware monitoring controller and some GPIO pins.
Note that this super-I/Os are embedded on some Atom-based LaCie NASes.
The GPIOs are used to control the LEDs and the hard drive power.
Changes since v3:
- Use request_muxed_region to protect the I/O ports against concurrent
accesses.
Changes since v2:
- Remove useless NULL setters for driver data.
Changes since v1:
- Enhance the commit message by describing what is a Super-I/O.
- Use self-explanatory names for the GPIO register macros.
- Add a comment to explain the platform device and driver registration.
- Fix gpio_get when GPIO is configured in input mode. I only had
the hardware to check this mode recently...
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SOCs in the OCTEON family have 16 (or in some cases 20) on-chip
GPIO pins, this driver handles them all. Configuring the pins as
interrupt sources is handled elsewhere (OCTEON's irq handling code).
Signed-off-by: David Daney <david.daney@cavium.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5633/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add gpio support for the on-board PLD found on some Kontron embedded modules.
Originally-from: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert gpio-tz1090 driver to use generic irqchips. This allows the
irq_ack, irq_mask, and irq_unmask callbacks and associated helper
functions to be removed. Also switch to using irq_setup_alt_chip() in
the irq_set_type callback instead of using __irq_set_handler_locked().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a GPIO driver for the low-power Powerdown Controller GPIOs in the
TZ1090 SoC.
The driver is instantiated by device tree and supports interrupts for
the SysWake GPIOs only.
Changes in v4:
- fix typos in DT bindings compatible properties
- reference Documentation/devicetree/bindings/gpio/gpio.txt in
gpio-ranges description in DT bindings
- fix gpio-ranges examples in DT bindings (it must now have 3 cells)
Changes in v3:
- separated from irq-imgpdc and removed arch/metag changes to allow
these patches to go upstream separately via the pinctrl[/gpio] trees
(particularly the pinctrl drivers depend on the new pinconf DT
bindings).
- some s/unsigned/unsigned int/.
- gpio-tz1090*: refer to <dt-bindings/gpio/gpio.h> and
<dt-bindings/interrupt-controller/irq.h> flags in bindings.
- gpio-tz1090*: move initcall from postcore to subsys.
Changes in v2:
- gpio-tz1090-pdc: remove references to Linux flags in dt bindings
- gpio-tz1090-pdc: make use of BIT() from linux/bitops.h
- gpio-tz1090-pdc: make register accessors inline to match pinctrl
- gpio-tz1090-pdc: update gpio-ranges to use 3 cells after recent ABI
breakage
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a GPIO driver for the main GPIOs found in the TZ1090 (Comet) SoC.
This doesn't include low-power GPIOs as they're controlled separately
via the Powerdown Controller (PDC) registers.
The driver is instantiated by device tree and supports interrupts for
all GPIOs.
Changes in v4:
- fix typos in DT bindings compatible properties
- reference Documentation/devicetree/bindings/gpio/gpio.txt in
gpio-ranges description in DT bindings
- fix gpio-ranges examples in DT bindings (it must now have 3 cells)
- gpio-tz1090: use of_property_read_u32 instead of of_get_property
Changes in v3:
- separated from irq-imgpdc and removed arch/metag changes to allow
these patches to go upstream separately via the pinctrl[/gpio] trees
(particularly the pinctrl drivers depend on the new pinconf DT
bindings).
- some s/unsigned/unsigned int/.
- some s/unsigned int/bool/ and use of BIT().
- gpio-tz1090*: refer to <dt-bindings/gpio/gpio.h> and
<dt-bindings/interrupt-controller/irq.h> flags in bindings.
- gpio-tz1090*: move initcall from postcore to subsys.
- gpio-tz1090: add REG_ prefix to some constants for consistency.
- gpio-tz1090: add comment to explain tz1090_gpio_irq_next_edge
cunningness.
Changes in v2:
- gpio-tz1090: remove references to Linux flags in dt bindings
- gpio-tz1090: make use of BIT() from linux/bitops.h
- gpio-tz1090: make register accessors inline to match pinctrl
- gpio-tz1090: update gpio-ranges to use 3 cells after recent ABI
breakage
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Incremental development for the Langwell (Atom SoC),
Xilinx, ICH and RCAR drivers.
- Cleanups from Jingoo Han, Axel Lin, Wei Jongjun,
Wolfram Sang, Tushar Behera, Sachin Kamat and Yijing Wang.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=5JfC
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is a batch of GPIO changes for v3.11. I have agreed with Grant
to take care of the pull requests for this development cycle.
No special things are happening in the GPIO tree this time (nice with
some calm) and I have been extra careful to do regression builds and
it's well boiled in -next.
GPIO changes for the v3.11 development cycle:
- Incremental development for the Langwell (Atom SoC), Xilinx, ICH
and RCAR drivers.
- Cleanups from Jingoo Han, Axel Lin, Wei Jongjun, Wolfram Sang,
Tushar Behera, Sachin Kamat and Yijing Wang"
* tag 'gpio-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (35 commits)
Gpio/trivial: replace numeric with standard PM state macros
gpiolib: remove warnning of allocations with IRQs disabled
gpio: grgpio: Staticize local symbols
gpio-langwell: remove Withney point support
gpio: ich: add GPO_BLINK support
gpio-sta2x11: Convert to use devm_ioremap_resource
gpio_msm: Convert to use devm_ioremap_resource
gpio-rcar: Use OUTDT when reading GPIOs configured as output
gpio-sta2x11: Fix potential NULL pointer dereference
gpio/omap: omap_gpio_init_context stub must be inline
gpio: msm-v1: Remove errant __devinit to fix compile
gpio: devres: make comments proper
GPIO: xilinx: Enable driver for Xilinx zynq
DT: Add documentation for gpio-xilinx
GPIO: xilinx: Use BIT macro
GPIO: xilinx: Use __raw_readl/__raw_writel IO functions
GPIO: xilinx: Add support for dual channel
GPIO: xilinx: Simplify driver probe function
gpio: sx150x: convert to use devm_* functions
MAINTAINERS: add linux-gpio mailing list
...
These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in
this branch, both containing almost no platform specific code at all,
since they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part of
the SoC specific code. With the changes done by Thomas Petazzoni, we can
now more easily have PCI host controller drivers as loadable modules and
keep them separate from the platform code in drivers/pci/host. This has
already led to the discovery that three platforms (exynos, spear and imx)
are actually using an identical PCIe host controller and will be able
to share a driver once support for spear and imx is added.
Conflicts:
* asm/glue-proc.h has one CPU type getting added that conflicts
with another addition in 3.10-rc7
* Simple context changes in arch/arm/Makefile and arch/arm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0r9S
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
- remove board file for exynos
- remove legacy files which are not used anymore
- decouple ARCH_EXYNOS from PLAT_S5P
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SHg+
-----END PGP SIGNATURE-----
Merge tag 'remove-nondt-exynos-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
From Kukjin Kim:
cleanup and removing dead code for only support DT for exynos
- remove board file for exynos
- remove legacy files which are not used anymore
- decouple ARCH_EXYNOS from PLAT_S5P
* tag 'remove-nondt-exynos-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (35 commits)
ARM: EXYNOS: Remove remaining dead code after non-DT support removal
ARM: EXYNOS: Remove legacy L2X0 initialization
ARM: EXYNOS: Use exynos_init_io() as map_io callback
ARM: EXYNOS: Remove custom init_irq callbacks
ARM: EXYNOS: Remove mach/regs-usb-phy.h header
thermal: exynos: Support both EXYNOS4X12 SoCs
ARM: EXYNOS: Remove unused base addresses from mach/map.h header
ARM: EXYNOS: Remove mach/irqs.h header
ARM: EXYNOS: Select SPARSE_IRQ for Exynos
ARM: SAMSUNG: Make legacy MFC support code depend on SAMSUNG_ATAGS
ARM: EXYNOS: Remove mach/regs-gpio.h header
ARM: EXYNOS: Remove mach/gpio.h
ARM: EXYNOS: Remove setup-i2c0.c
ARM: EXYNOS: Do not select legacy Kconfig symbols any more
ARM: SAMSUNG: Include most of mach/ headers conditionally
ARM: EXYNOS: Decouple ARCH_EXYNOS from PLAT_S5P
USB: Check for ARCH_EXYNOS separately
platform: Check for ARCH_EXYNOS separately
ARM: SAMSUNG: Compile legacy IRQ and GPIO PM code only with ATAGS support
ARM: EXYNOS: Provide compatibility stubs for PM code in pm-core.h header
...
Conflicts:
arch/arm/mach-exynos/Kconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds Kconfig entry that selects whether legacy Samsung GPIO
driver should be built or not. For platforms that support only DT based
boot, the new pinctrl driver is used and so the old one is not needed.
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Enable gpio driver for usage on Xilinx ARM zynq platform.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These are a handful of cleanups to the MSM tree. The gpio cleanups
get us closer to having proper pinmux and gpio support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=9wS3
-----END PGP SIGNATURE-----
Merge tag 'msm-cleanup-for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/cleanup
From David Brown:
Cleanups for MSM for 3.11
These are a handful of cleanups to the MSM tree. The gpio cleanups
get us closer to having proper pinmux and gpio support.
* tag 'msm-cleanup-for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
mfd: ssbi: Use devm_* and simplify code
gpio: msm: Add device tree and irqdomain support for gpio-msm-v2
ARM: msm: Remove gpiomux-v2 and re-organize MSM_GPIOMUX configs
msm: iomap: Remove unused bases and mappings
msm: Remove unused file core.h
ARM: msm: Remove init_irq declaration in machine description
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/boot/dts/msm8660-surf.dts
arch/arm/boot/dts/msm8960-cdp.dts
This cleans up the gpio-msm-v2 driver of all the global define usage.
The number of gpios are now defined in the device tree. This enables
adding irqdomain support as well.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
max7301 is controlled through SPI interface which means another driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes below build error when CONFIG_SPI_MASTER=y && CONFIG_I2C=m &&
CONFIG_GPIO_MCP23S08=y.
LD init/built-in.o
drivers/built-in.o: In function `mcp23017_write':
clkdev.c:(.text+0x1e14): undefined reference to `i2c_smbus_write_word_data'
drivers/built-in.o: In function `mcp23017_read':
clkdev.c:(.text+0x1e24): undefined reference to `i2c_smbus_read_word_data'
drivers/built-in.o: In function `mcp23008_write':
clkdev.c:(.text+0x1e8c): undefined reference to `i2c_smbus_write_byte_data'
drivers/built-in.o: In function `mcp23008_read':
clkdev.c:(.text+0x1e98): undefined reference to `i2c_smbus_read_byte_data'
drivers/built-in.o: In function `mcp23008_read_regs':
clkdev.c:(.text+0x1ed0): undefined reference to `i2c_smbus_read_byte_data'
drivers/built-in.o: In function `mcp23s08_init':
clkdev.c:(.init.text+0x30): undefined reference to `i2c_register_driver'
drivers/built-in.o: In function `mcp23s08_exit':
clkdev.c:(.exit.text+0x30): undefined reference to `i2c_del_driver'
make: *** [vmlinux] Error 1
When CONFIG_I2C=m, meaning we can't build the drivers in with I2C support.
Thus don't allow the drivers to be compiled as built-in when CONFIG_I2C=m.
The real fix though is to break the driver apart into a SPI part, an I2C part
and a common part. But that's something for 3.11 while this is something for
3.10/stable.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
These patches are all for Renesas shmobile, and depend on the earlier
pinctrl updates. Remarkably, this adds support for three new SoCs:
r8a73a4, r8a73a4 and r8a7778. The bulk of the code added for these is
for pinctrl (using the new subsystem) and for clocks (not yet using the
common clock subsystem). The latter will have to get converted in one
of the upcoming releases, but shmobile is not ready for that yet.
The series also contains Renesas shmobile board changes, adding one
board file for each of the three new SoCs. These boards are using a
mix of classic and device-tree based probing, as there is still a lot of
infrastructure in shmobile that has not been converted to DT yet. Once
those are resolved to the degree that no board specific setup code is
needed, they can get folded into the respective SoC setup files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xaLf
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 2) from Arnd Bergmann:
"These patches are all for Renesas shmobile, and depend on the earlier
pinctrl updates. Remarkably, this adds support for three new SoCs:
r8a73a4, r8a73a4 and r8a7778. The bulk of the code added for these is
for pinctrl (using the new subsystem) and for clocks (not yet using
the common clock subsystem). The latter will have to get converted in
one of the upcoming releases, but shmobile is not ready for that yet.
The series also contains Renesas shmobile board changes, adding one
board file for each of the three new SoCs. These boards are using a
mix of classic and device-tree based probing, as there is still a lot
of infrastructure in shmobile that has not been converted to DT yet.
Once those are resolved to the degree that no board specific setup
code is needed, they can get folded into the respective SoC setup files."
* tag 'soc-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (78 commits)
ARM: shmobile: use r8a7790 timer setup code on Lager
ARM: shmobile: force enable of r8a7790 arch timer
ARM: shmobile: Add second I/O range for r8a7790 PFC
ARM: shmobile: bockw: enable network settings on bootargs
ARM: shmobile: bockw: add SMSC ethernet support
ARM: shmobile: R8A7778: add Ether support
ARM: shmobile: bockw: enable SMSC ethernet on defconfig
ARM: shmobile: r8a7778: add r8a7778_init_irq_extpin()
ARM: shmobile: r8a7778: remove pointless PLATFORM_INFO()
ARM: shmobile: mackerel: clean up MMCIF vs. SDHI1 selection
ARM: shmobile: mackerel: add interrupt names for SDHI0
ARM: shmobile: mackerel: switch SDHI and MMCIF interfaces to slot-gpio
ARM: shmobile: mackerel: remove OCR masks, where regulators are used
ARM: shmobile: mackerel: SDHI resources do not have to be numbered
ARM: shmobile: Initial r8a7790 Lager board support
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
ARM: shmobile: APE6EVM base support
ARM: shmobile: kzm9g-reference: add ethernet support
ARM: shmobile: add R-Car M1A Bock-W platform support
...
The usual selection of bug fixes and driver updates for GPIO. Nothing
really stands out except the addition of the GRGPIO driver and some
enhacements to ACPI support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PwUd
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull GPIO changes from Grant Likely:
"The usual selection of bug fixes and driver updates for GPIO. Nothing
really stands out except the addition of the GRGPIO driver and some
enhacements to ACPI support"
I'm pulling this despite the earlier mess. Let's hope it compiles these
days.
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux: (46 commits)
gpio: grgpio: Add irq support
gpio: grgpio: Add device driver for GRGPIO cores
gpiolib-acpi: introduce acpi_get_gpio_by_index() helper
GPIO: gpio-generic: remove kfree() from bgpio_remove call
gpio / ACPI: Handle ACPI events in accordance with the spec
gpio: lpc32xx: Fix off-by-one valid range checking for bank
gpio: mcp23s08: convert driver to DT
gpio/omap: force restore if context loss is not detectable
gpio/omap: optimise interrupt service routine
gpio/omap: remove extra context restores in *_runtime_resume()
gpio/omap: free irq domain in probe() failure paths
gpio: gpio-generic: Add 16 and 32 bit big endian byte order support
gpio: samsung: Add terminating entry for exynos_pinctrl_ids
gpio: mvebu: add dbg_show function
MAX7301 GPIO: Do not force SPI speed when using OF Platform
gpio: gpio-tps65910.c: fix checkpatch error
gpio: gpio-timberdale.c: fix checkpatch error
gpio: gpio-tc3589x.c: fix checkpatch errors
gpio: gpio-stp-xway.c: fix checkpatch error
gpio: gpio-sch.c: fix checkpatch error
...
This driver supports GRGPIO gpio cores available in the GRLIB VHDL IP
core library from Aeroflex Gaisler.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GENERIC_GPIO has been made equivalent to GPIOLIB in architecture code
and all driver code has been switch to depend on GPIOLIB. It is thus
safe to have GENERIC_GPIO removed.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
With the move to a combined pinctrl/gpio driver, the arch-vt8500
gpio driver is no longer required.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch is V3 of a GPIO driver for the R-Car series of
SoCs from Renesas. This driver is designed to be reusable
between multiple SoCs that share the same basic building block,
but so far it has only been used on R-Car H1 (r8a7779).
Each driver instance handles 32 GPIOs with individually
maskable IRQs. The driver operates on a single I/O memory
range and the 32 GPIOs are hooked up a single interrupt.
In the case of R-Car H1 either external IRQ pins or GPIOs
with interrupts can be used for on-board interupts. For
external IRQs 4 pins are supported, and in the case of GPIO
there are 202 GPIOS as 202 interrupts hooked up via 6 driver
instances and to the GIC and the Cortex-A9 Quad.
At this point this driver is interfacing as a regular
platform device driver. In the future DT support will be
submitted as an incremental feature patch.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Lynxpoint gpio driver uses X86 specific io-ports to control gpios
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This branch contains the usual set of individual driver improvements and
bug fixes, as well as updates to the core code. The more notable changes
include:
- Internally add new API for referencing GPIOs by gpio_desc instead of
number. Eventually this will become a public API
- ACPI GPIO binding support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJRK77kAAoJEEFnBt12D9kBwZ0P/iJ++tvmUg9mt9qzN0Le0Q02
TKCQpgOivxng03oTcLIQRK46PNPWdq2zDb1v5seqXKxdMjRd++WLxPxj4eRZNdqA
J0K820KvqYSLAqEUDwqO288ciOyP6ThDfeT+SUUUCOwFHkFCVS0xYuxLjcX0evah
pcXuIu6nev2Yo/RivgXVaVkOTVBf7ssR7rTpdkDl/RvK2BMZTfpmt4fAXdDcCb9k
JlBeSC6Ifx6iUcl+lV+jA0PeA7vOEHBhXWqoy5ivtNPcBbPL//cz0ZdAL0jfVtgn
17RPugskNv/s2uVJlhiyKA3kF2IzbE3pKGxyl2Teb4Xus398pqqaHPtiLNeKIiSV
KUJRIu2mGdvb4Vyvno0e5Vll9PcUPX0uIeQ2uzrMAB7XtI4EHw7d9+qwj4qOI6Dg
edCFNcI9zTeuU/Z3fAg/+ufdIY7muQz8OsKnh3R8fY29SVSa+6o6TT+tgX5M7tjH
IEI11RaYQQEJSri9bAR0vE1nsFleWsoW6QljVIHLpNS/tBz/S8KYpbQ5qPNXknxf
lgD0FzkNYPWWi9D3wNutwNeaktCacRfcCTH1Z4FzE+PmxoYeiCzf/4pjFbxU06dm
WJ7i8E0SRrVW+cM8z7M+Lj6emqtQ5En0bg5ZTo75SM2X+9sNrWtw3UMQ7Ea4gxKM
362n9tWp2k626DixWzBd
=JN4M
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull GPIO changes from Grant Likely:
"This branch contains the usual set of individual driver improvements
and bug fixes, as well as updates to the core code. The more notable
changes include:
- Internally add new API for referencing GPIOs by gpio_desc instead
of number. Eventually this will become a public API
- ACPI GPIO binding support"
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux: (33 commits)
arm64: select ARCH_WANT_OPTIONAL_GPIOLIB
gpio: em: Use irq_domain_add_simple() to fix runtime error
gpio: using common order: let 'static const' instead of 'const static'
gpio/vt8500: memory cleanup missing
gpiolib: Fix locking on gpio debugfs files
gpiolib: let gpio_chip reference its descriptors
gpiolib: use descriptors internally
gpiolib: use gpio_chips list in gpiochip_find_base
gpiolib: use gpio_chips list in sysfs ops
gpiolib: use gpio_chips list in gpiochip_find
gpiolib: use gpio_chips list in gpiolib_sysfs_init
gpiolib: link all gpio_chips using a list
gpio/langwell: cleanup driver
gpio/langwell: Add Cloverview ids to pci device table
gpio/lynxpoint: add chipset gpio driver.
gpiolib: add missing braces in gpio_direction_show
gpiolib-acpi: Fix error checks in interrupt requesting
gpio: mpc8xxx: don't set IRQ_TYPE_NONE when creating irq mapping
gpiolib: remove gpiochip_reserve()
arm: pxa: tosa: do not use gpiochip_reserve()
...
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data consolidation,
OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee Jones. In
particular, the debugfs and the sysct interfaces got extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the twl-core
driver, with a much needed module id lookup code improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the palmas
GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra and
Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and ab9540 based
devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a better
card detection code path and now also supports the RTS5227 chipset, thanks
to Wei Wang and Roger Tseng.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BhC1
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS updates from Samuel Ortiz:
"This is the MFD pull request for the 3.9 merge window.
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data
consolidation, OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee
Jones. In particular, the debugfs and the sysct interfaces got
extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the
twl-core driver, with a much needed module id lookup code
improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the
palmas GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra
and Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and
ab9540 based devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to
Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a
better card detection code path and now also supports the RTS5227
chipset, thanks to Wei Wang and Roger Tseng."
* tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (109 commits)
mfd: lpc_ich: Use devres API to allocate private data
mfd: lpc_ich: Add Device IDs for Intel Wellsburg PCH
mfd: lpc_sch: Accomodate partial population of the MFD devices
mfd: da9052-i2c: Staticize da9052_i2c_fix()
mfd: syscon: Fix sparse warning
mfd: twl-core: Fix kernel panic on boot
mfd: rtsx: Fix issue that booting OS with SD card inserted
mfd: ab8500: Fix compile error
mfd: Add missing GENERIC_HARDIRQS dependecies
Documentation: Add docs for max8925 dt
mfd: max8925: Add dts
mfd: max8925: Support dt for backlight
mfd: max8925: Fix onkey driver irq base
mfd: max8925: Fix mfd device register failure
mfd: max8925: Add irqdomain for dt
mfd: vexpress: Allow vexpress-sysreg to self-initialise
mfd: rtsx: Support RTS5227
mfd: rtsx: Implement driving adjustment to device-dependent callbacks
mfd: vexpress: Add pseudo-GPIO based LEDs
mfd: ab8500: Rename ab8500 to abx500 for hwmon driver
...
Pull s390 update from Martin Schwidefsky:
"The most prominent change in this patch set is the software dirty bit
patch for s390. It removes __HAVE_ARCH_PAGE_TEST_AND_CLEAR_DIRTY and
the page_test_and_clear_dirty primitive which makes the common memory
management code a bit less obscure.
Heiko fixed most of the PCI related fallout, more often than not
missing GENERIC_HARDIRQS dependencies. Notable is one of the 3270
patches which adds an export to tty_io to be able to resize a tty.
The rest is the usual bunch of cleanups and bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits)
s390/module: Add missing R_390_NONE relocation type
drivers/gpio: add missing GENERIC_HARDIRQ dependency
drivers/input: add couple of missing GENERIC_HARDIRQS dependencies
s390/cleanup: rename SPP to LPP
s390/mm: implement software dirty bits
s390/mm: Fix crst upgrade of mmap with MAP_FIXED
s390/linker skript: discard exit.data at runtime
drivers/media: add missing GENERIC_HARDIRQS dependency
s390/bpf,jit: add vlan tag support
drivers/net,AT91RM9200: add missing GENERIC_HARDIRQS dependency
iucv: fix kernel panic at reboot
s390/Kconfig: sort list of arch selected config options
phylib: remove !S390 dependeny from Kconfig
uio: remove !S390 dependency from Kconfig
dasd: fix sysfs cleanup in dasd_generic_remove
s390/pci: fix hotplug module init
s390/pci: cleanup clp page allocation
s390/pci: cleanup clp inline assembly
s390/perf: cpum_cf: fallback to software sampling events
s390/mm: provide PAGE_SHARED define
...
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
The VIA VX855/VX875 GPIO and RDC R-321x GPIO support drivers select
MFD_CORE which itself depends on GENERIC_HARDIRQ support.
So add this dependency to these two drivers as well to prevent
selection of MFD_CORE.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add gpio driver for TI Palmas series PMIC. This has 8 gpio which can
work as input/output.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add gpio support for Intel Lynxpoint chipset.
Lynxpoint supports 94 gpio pins which can generate interrupts.
Driver will fail requests for pins that are marked as owned by ACPI, or
set in an alternate mode (non-gpio).
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The AB8500 GPIO driver has been marked BROKEN for ages, and we
have something better in store: a shiny new pinctrl driver. So
let use delete this old driver as the first step.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some architectures (e.g. blackfin) provide gpio API without requiring
GPIOLIB support (ARCH_WANT_OPTIONAL_GPIOLIB). devm_gpio_* functions
should also work for these architectures, since they do not really
depend on GPIOLIB.
Add a new option GPIO_DEVRES (enabled by default) to control the build
of devres.c. It also removes the empty version of devm_gpio_*
functions for !GENERIC_GPIO build from linux/gpio.h, and moves the
function declarations from asm-generic/gpio.h into linux/gpio.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building without device tree support (for the mv78x00 SoCs for
example), the build failed because of_irq_count is undeclared. However
mvebu-gpio is not designed to build without device tree support. So
make it depends on OF_CONFIG, remove the #ifdef OF_CONFIG line and the
platform_device_id.
Tested on RD-78x00-mASA, DB-78460-BP, DB-88F6710-BP-DDR3,
DB-MV784MP-GP, Mirabox and OpenBlocks AX3.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We have several new drivers, most of the time coming with their sub devices
drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap I/O and IRQ
APIs and a conversion to the recently added PWM framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have Mark's
wm5xxx and wm8xxx patchset.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F790
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS update from Samuel Ortiz:
"This is the MFD patch set for the 3.8 merge window.
We have several new drivers, most of the time coming with their sub
devices drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap
I/O and IRQ APIs and a conversion to the recently added PWM
framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have
Mark's wm5xxx and wm8xxx patchset."
Far amount of annoying but largely trivial conflicts. Many due to
__devinit/exit removal, others due to one or two of the new drivers also
having come in through another tree.
* tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (119 commits)
mfd: tps6507x: Convert to devm_kzalloc
mfd: stmpe: Update DT support for stmpe driver
mfd: wm5102: Add readback of DSP status 3 register
mfd: arizona: Log if we fail to create the primary IRQ domain
mfd: tps80031: MFD_TPS80031 needs to select REGMAP_IRQ
mfd: tps80031: Add terminating entry for tps80031_id_table
mfd: sta2x11: Fix potential NULL pointer dereference in __sta2x11_mfd_mask()
mfd: wm5102: Add tuning for revision B
mfd: arizona: Defer patch initialistation until after first device boot
mfd: tps65910: Fix wrong ack_base register
mfd: tps65910: Remove unused data
mfd: stmpe: Get rid of irq_invert_polarity
mfd: ab8500-core: Fix invalid free of devm_ allocated data
mfd: wm5102: Mark DSP memory regions as volatile
mfd: wm5102: Correct default for LDO1_CONTROL_2
mfd: arizona: Register haptics devices
mfd: wm8994: Make current device behaviour the default
mfd: tps65090: MFD_TPS65090 needs to select REGMAP_IRQ
mfd: Fix stmpe.c build when OF is not enabled
mfd: jz4740-adc: Use devm_kzalloc
...
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
Continued device tree conversion and enablement across a number of
platforms; Kirkwood, tegra, i.MX, Exynos, zynq and a couple of other
smaller series as well.
ux500 has seen continued conversion for platforms. Several platforms have
seen pinctrl-via-devicetree conversions for simpler multiplatform. Tegra
is adding data for new devices/drivers, and Exynos has a bunch of new
bindings and devices added as well.
So, pretty much the same progression in the right direction as the last
few releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Rk9v
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree conversions and enablement from Olof Johansson:
"Continued device tree conversion and enablement across a number of
platforms; Kirkwood, tegra, i.MX, Exynos, zynq and a couple of other
smaller series as well.
ux500 has seen continued conversion for platforms. Several platforms
have seen pinctrl-via-devicetree conversions for simpler
multiplatform. Tegra is adding data for new devices/drivers, and
Exynos has a bunch of new bindings and devices added as well.
So, pretty much the same progression in the right direction as the
last few releases."
Fix up conflicts as per Olof.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (185 commits)
ARM: ux500: Rename dbx500 cpufreq code to be more generic
ARM: dts: add missing ux500 device trees
ARM: ux500: Stop registering the PCM driver from platform code
ARM: ux500: Move board specific GPIO info out to subordinate DTS files
ARM: ux500: Disable the MMCI gpio-regulator by default
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
...
Primarily device driver additions, features and bug fixes. Not much
touching gpio common subsystem support. Should not be scary.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2XeO
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO updates from Grant Likely:
"GPIO follow up patch and type change for v3.5 merge window
Primarily device driver additions, features and bug fixes. Not much
touching gpio common subsystem support. Should not be scary."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
gpio: Provide the STMPE GPIO driver with its own IRQ Domain
gpio: add TS-5500 DIO blocks support
gpio: pcf857x: use client->irq for gpio_to_irq()
gpio: stmpe: Add DT support for stmpe gpio
gpio: pl061 depends on ARM
gpio/pl061: remove old comment
gpio: SPEAr: add spi chipselect control driver
gpio: gpio-max710x: Support device tree probing
gpio: twl4030: Use only TWL4030_MODULE_LED for LED configuration
gpio: tegra: read output value when gpio is set in direction_out
gpio: pca953x: Add compatible strings to gpio-pca953x driver
gpio: pca953x: Register an IRQ domain
gpio: mvebu: Set free callback for gpio_chip
gpio: tegra: Drop exporting static functions
gpio: tegra: Staticize non-exported symbols
gpio: tegra: fix suspend/resume apis
gpio-pch: Set parent dev for gpio chip
gpio: em: Fix build errors
GPIO: clps711x: use platform_device_unregister in gpio_clps711x_init()
gpio/tc3589x: convert to use the simple irqdomain
...
Technologic Systems TS-5500 provides digital I/O lines exposed through
pin blocks. On this platform, there are three of them, named DIO1, DIO2
and LCD port, that may be used as a DIO block.
The TS-5500 pin blocks are described in the product's wiki:
http://wiki.embeddedarm.com/wiki/TS-5500#Digital_I.2FO
This driver is not limited to the TS-5500 blocks. It can be extended to
support similar boards pin blocks, such as on the TS-5600.
This patch is the V2 of the previous https://lkml.org/lkml/2012/9/25/671
with corrections suggested by Linus Walleij.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit dece904d (gpio: pl061: use chained_irq_* functions in irq
handler) introduced chained_irq_enter/exit, which is only
available for arch/arm and the driver won't compile elsewhere.
The dependency is thus made explicit, because AMBA is used in the x86
world by a PCI-to-AMBA bridge, to be submitted.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for translating ACPI GPIO pin numbers to Linux GPIO API pins.
Needs a gpio controller driver with the acpi handler hook set.
Drivers can use acpi_get_gpio() to translate ACPI5 GpioIO and GpioInt
resources to Linux GPIO's.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Kirkwood & Dove can also use this driver, so expand the scope to
include all platform orion devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This adds the mfd cell to use the gpio a and gpio b part
of the Nano River Technologies viperboard.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
SPEAr platform provides a provision to control chipselects of ARM PL022
Prime Cell spi controller through its system registers, which otherwise
remains under PL022 control which some protocols do not want.
This commit intends to provide the spi chipselect control in software over
gpiolib interface. spi chip drivers can use the exported gpiolib interface to
define their chipselect through DT or platform data.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver accesses the of_node field of struct gpio_chip, which is only
available if OF_GPIO is selected. This solves a build issue on SPARC
which conflicts with OF_GPIO and therefore does not provide this field.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The CLPS711X CPUs provide some GPIOs for use in the system. This
driver provides support for these via gpiolib. Due to platform
limitations, driver does not support interrupts, only inputs and
outputs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is the GPIO patch for the DA9055 PMIC. This patch has got
dependency on the DA9055 MFD core.
This patch is functionally tested on SMDK6410 board.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform merges,
so they were kept separate from the rest, and not separated into the
traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which
is a piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP since
it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and mvebu
- New clean gpio driver for mvebu
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xVaJ
-----END PGP SIGNATURE-----
Merge tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM soc platform updates from Olof Johansson:
"This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform
merges, so they were kept separate from the rest, and not separated
into the traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and
non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which is a
piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP
since it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few
drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and
mvebu
- New clean gpio driver for mvebu"
* tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (98 commits)
ARM: mvebu: fix build breaks from multi-platform conversion
ARM: OMAP4460/4470: PMU: Enable PMU for OMAP4460/70
ARM: OMAP2+: PMU: Add runtime PM support
ARM: OMAP4430: PMU: prepare to create PMU device via HWMOD
ARM: OMAP2+: PMU: Convert OMAP2/3 devices to use HWMOD
ARM: OMAP3: hwmod data: Add debugss HWMOD data
ARM: OMAP2+: clockdomain/hwmod: add workaround for EMU clockdomain idle problems
ARM: OMAP: Add a timer attribute for timers that can interrupt the DSP
hwrng: OMAP: remove SoC restrictions from driver registration
ARM: OMAP: split OMAP1, OMAP2+ RNG device registration
hwrng: OMAP: convert to use runtime PM
hwrng: OMAP: store per-device data in per-device variables, not file statics
ARM: OMAP2xxx: hwmod/CM: add RNG integration data
ARM: OMAP2+: gpmc: minimal driver support
ARM: OMAP2+: gpmc: Adapt to HWMOD
ARM: OMAP2/3: hwmod data: add gpmc
ARM: OMAP4: hwmod data: add mmu hwmod for ipu and dsp
ARM: OMAP3: hwmod data: add mmu data for iva and isp
ARM: OMAP: iommu: fix including iommu.h without IOMMU_API selected
ARM: OMAP4: hwmod data: add missing HWMOD_NO_IDLEST flags to some PRCM IP blocks
...
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x, palmas,
ab8500, wm8994, wm5110, max8907 and the tps65xxx family.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n6lp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"MFD bits for the 3.7 merge window.
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."
Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.
Guys, DON'T REBASE!
* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
ARM: dts: Enable 88pm860x pmic
mfd: 88pm860x: Move gpadc init into touch
mfd: 88pm860x: Device tree support
mfd: 88pm860x: Use irqdomain
mfd: smsc: Add support for smsc gpio io/keypad driver
backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
mfd: DA9055 core driver
mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
mfd: wm5110: Add register patches for revision B
mfd: wm5110: Disable control interface error report for WM5110 rev B
mfd: max8907: Remove regulator-compatible from DT docs
backlight: Add TPS65217 WLED driver
mfd: Add backlight as subdevice to the tps65217
mfd: Provide the PRCMU with its own IRQ domain
mfd: Fix max8907 sparse warning
mfd: Add lp8788 mfd driver
mfd: dbx500: Provide a more accurate smp_twd clock
mfd: rc5t583: Fix warning messages
regulator: palmas: Add DT support
mfd: palmas: Change regulator defns to better suite DT
...
- refactoring from Thierry Redding at Arnd Bergmann's request to use
the seq_file iterator interface in gpiolib.
- A new driver for Avionic Design's N-bit GPIO expander.
- Two instances of mutexes replaced by spinlocks from Axel Lin to
code that is supposed to be fastpath compliant.
- IRQ demuxer and gpio_to_irq() support for pcf857x by Kuninori
Morimoto.
- Dynamic GPIO numbers, device tree support, daisy chaining and some
other fixes for the 74x164 driver by Maxime Ripard.
- IRQ domain and device tree support for the tc3589x driver by
Lee Jones.
- Some conversion to use managed resources devm_* code.
- Some instances of clk_prepare() or clk_prepare_enable() added to
support the new, stricter common clock framework.
- Some for_each_set_bit() simplifications.
- Then a lot of fixes as we fixed up all of the above tripping over
our own shoelaces and that kind of thing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=jbUM
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"So this is the LW GPIO patch stack for v3.7:
- refactoring from Thierry Redding at Arnd Bergmann's request to use
the seq_file iterator interface in gpiolib.
- A new driver for Avionic Design's N-bit GPIO expander.
- Two instances of mutexes replaced by spinlocks from Axel Lin to
code that is supposed to be fastpath compliant.
- IRQ demuxer and gpio_to_irq() support for pcf857x by Kuninori
Morimoto.
- Dynamic GPIO numbers, device tree support, daisy chaining and some
other fixes for the 74x164 driver by Maxime Ripard.
- IRQ domain and device tree support for the tc3589x driver by Lee
Jones.
- Some conversion to use managed resources devm_* code.
- Some instances of clk_prepare() or clk_prepare_enable() added to
support the new, stricter common clock framework.
- Some for_each_set_bit() simplifications.
- Then a lot of fixes as we fixed up all of the above tripping over
our own shoelaces and that kind of thing."
* tag 'gpio-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (34 commits)
gpio: pcf857x: select IRQ_DOMAIN
gpio: Document device_node's det_debounce
gpio-lpc32xx: Add GPI_28
gpio: adnp: dt: Reference generic interrupt binding
gpio: Add Avionic Design N-bit GPIO expander support
gpio: pxa: using for_each_set_bit to simplify the code
gpio_msm: using for_each_set_bit to simplify the code
gpio: Enable the tc3298x GPIO expander driver for Device Tree
gpio: Provide the tc3589x GPIO expander driver with an IRQ domain
ARM: shmobile: kzm9g: use gpio-keys instead of gpio-keys-polled
gpio: pcf857x: fixup smatch WARNING
gpio: 74x164: Add support for the daisy-chaining
gpio: 74x164: dts: Add documentation for the dt binding
dt: Fix incorrect reference in gpio-led documentation
gpio: 74x164: Add device tree support
gpio: 74x164: Use dynamic gpio number assignment if no pdata is present
gpio: 74x164: Use devm_kzalloc
gpio: 74x164: Use module_spi_driver boiler plate function
gpio: sx150x: Use irq_data_get_irq_chip_data() at appropriate places
gpio: em: Use irq_data_get_irq_chip_data() at appropriate places
...
Patch 6e20a0a4 "gpio: pcf857x: enable gpio_to_irq() support"
added IRQ domain support to the pcf857x driver, but some configurations
(e.g. davinci_all_defconfig) don't already enable CONFIG_IRQ_DOMAIN.
Always selecting it from the Kconfig in this case is what other
such drivers do as well, and avoids these build errors:
Without this patch, building davinci_all_defconfig results in:
drivers/gpio/gpio-pcf857x.c: In function 'pcf857x_to_irq':
drivers/gpio/gpio-pcf857x.c:167:2: error: implicit declaration of function 'irq_create_mapping'
drivers/gpio/gpio-pcf857x.c: In function 'pcf857x_irq_demux_work':
drivers/gpio/gpio-pcf857x.c:183:3: error: implicit declaration of function 'irq_find_mapping'
drivers/gpio/gpio-pcf857x.c: In function 'pcf857x_irq_domain_cleanup':
drivers/gpio/gpio-pcf857x.c:218:3: error: implicit declaration of function 'irq_domain_remove'
drivers/gpio/gpio-pcf857x.c: In function 'pcf857x_irq_domain_init':
drivers/gpio/gpio-pcf857x.c:230:2: error: implicit declaration of function 'irq_domain_add_linear'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver aims at replacing the arch/arm/plat-orion/gpio.c driver,
and is designed to be compatible with all Marvell EBU SoCs: Orion,
Kirkwood, Dove, Armada 370/XP and Discovery.
It has been successfully tested on Dove and Armada XP at the moment.
Compared to the plat-orion driver, this new driver has the following
added benefits:
*) Support for Armada 370 and Armada XP
*) It is integrated with the mvebu pinctrl driver so that GPIO pins
are properly muxed, and the GPIO driver knows which GPIO pins are
output-only or input-only.
*) Properly placed in drivers/gpio
*) More extensible mechanism to support platform differences. The
plat-orion driver uses a simple mask-offset DT property, which
works fine for Discovery MV78200 but not for Armada XP. The new
driver uses different compatible strings to identify the different
variants of the GPIO controllers.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Converted the existing arch-vt8500 gpio to a platform_device.
Added support for WM8505 and WM8650 GPIO controllers.
Replaced existing readl/writel calls with _relaxed variants.
Replaced existing unsigned variables with u32 to match register size.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
TWL6040 provides GPO lines to be used for controlling external devices.The number
of lines different between versions: twl6040 have 3 GPO while TWL6041 have 1.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This commit adds a driver for the Avionic Design N-bit GPIO expander.
The expander provides a variable number of GPIO pins with interrupt
support.
Changes in v2:
- allow building the driver as a module
- assign of_node unconditionally
- use linear mapping IRQ domain
- properly cleanup IRQ domain
- add OF device table and annotate device tables
- emulate rising and falling edge triggers
- increase #gpio-cells to 2
- drop support for !OF
- use IS_ENABLED to conditionalize DEBUG_FS code
Changes in v3:
- make IRQ support runtime configurable (interrupt-controller property)
- drop interrupt-controller and #interrupt-cells from DT binding
- add inline to_adnp() function to wrap container_of() macro
- consistently use adnp as name for struct adnp variables
- remove irq_mask_cur and rename irq_mask to irq_enable
- fix a subtle deadlock in adnp_gpio_direction_output()
- remove dynamic allocations from debugfs code
- rename regs to num_regs to avoid confusion
- annotate non-trivial code with comments
- don't acquire mutex in adnp_gpio_get()
- assume NO_IRQ == 0
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The fix for MFD part is merged so remove the broken mark for da9052 gpio driver.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make GPIO_MC9S08DZ60 depend on I2C=y, this fixes below build error:
LD init/built-in.o
drivers/built-in.o: In function `mc9s08dz60_get_value':
clk-fixed-factor.c:(.text+0x7214): undefined reference to `i2c_smbus_read_byte_data'
drivers/built-in.o: In function `mc9s08dz60_set':
clk-fixed-factor.c:(.text+0x727c): undefined reference to `i2c_smbus_read_byte_data'
clk-fixed-factor.c:(.text+0x72bc): undefined reference to `i2c_smbus_write_byte_data'
drivers/built-in.o: In function `mc9s08dz60_i2c_driver_init':
clk-fixed-factor.c:(.init.text+0x290): undefined reference to `i2c_register_driver'
drivers/built-in.o: In function `mc9s08dz60_i2c_driver_exit':
clk-fixed-factor.c:(.exit.text+0x2c): undefined reference to `i2c_del_driver'
make: *** [vmlinux] Error 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c28c
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD bits from Samuel Ortiz:
"We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core."
Fix up mostly trivial conflicts, with the exception of
drivers/usb/host/ehci-omap.c in particular, which had some
re-organization of the reset sequence (commit 1a49e2ac9651: "EHCI:
centralize controller initialization") that clashed with commit
2761a63945 ("mfd: USB: Fix the omap-usb EHCI ULPI PHY reset fix
issues").
In particular, commit 2761a63945 moved the usb_add_hcd() to the
*middle* of the reset sequence, which clashes fairly badly with the
reset sequence re-organization (although it could have been done inside
the new omap_ehci_init() function).
I left that part of commit 2761a63945 just undone.
* tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (110 commits)
mfd: Ensure AB8500 platform data is passed through db8500-prcmu to MFD Core
mfd: Arizone core should select MFD_CORE
mfd: Fix arizona-irq.c build by selecting REGMAP_IRQ
mfd: Add debug trace on entering and leaving arizone runtime suspend
mfd: Correct tps65090 cell names
mfd: Remove gpio support from tps6586x core driver
ARM: tegra: defconfig: Enable tps6586x gpio
gpio: tps6586x: Add gpio support through platform driver
mfd: Cache tps6586x register through regmap
mfd: Use regmap for tps6586x register access.
mfd: Use devm managed resources for tps6586x
input: Add onkey support for 88PM80X PMIC
mfd: Add support for twl6041
mfd: Fix twl6040 revision information
mfd: Matches should be NULL when populate anatop child devices
input: ab8500-ponkey: Create AB8500 domain IRQ mapping
mfd: Add missing out of memory check for pcf50633
Documentation: Describe the AB8500 Device Tree bindings
mfd: Add tps65910 32-kHz-crystal-input init
mfd: Drop modifying mc13xxx driver's id_table in probe
...
- New driver for AMD-8111 southbridge GPIOs
- New driver for Wolfson Micro Arizona devices
- Propagate device tree parse errors
- Probe deferral finalizations - all expected calls to
GPIO will now hopefully request deferral where apropriate
- Misc updates to TCA6424, WM8994, LPC32xx, PCF857x, Samsung
MXC, OMAP and PCA953X drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=tujx
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
- New driver for AMD-8111 southbridge GPIOs
- New driver for Wolfson Micro Arizona devices
- Propagate device tree parse errors
- Probe deferral finalizations - all expected calls to GPIO will now
hopefully request deferral where apropriate
- Misc updates to TCA6424, WM8994, LPC32xx, PCF857x, Samsung MXC, OMAP
and PCA953X drivers.
Fix up gpio_idx conflicts in drivers/gpio/gpio-mxc.c
* tag 'gpio-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: of_get_named_gpio_flags() return -EPROBE_DEFER if GPIO not yet available
gpiolib: Defer failed gpio requests by default
MAINTAINERS: add entry OMAP GPIO driver
gpio/pca953x: increase variables size to support 24 bit of data
GPIO: PCA953X: Increase size of invert variable to support 24 bit
gpio/omap: move bank->dbck initialization to omap_gpio_mod_init()
gpio/mxc: use the edge_sel feature if available
gpio: propagate of_parse_phandle_with_args errors
gpio: samsung: add flags specifier to device-tree binding
gpiolib: Add support for Wolfson Microelectronics Arizona class devices
gpio: gpio-lpc32xx: Add gpio_to_irq mapping
gpio: pcf857x: share 8/16 bit access functions
gpio: LPC32xx: Driver cleanup
MAINTAINERS: Add Wolfson gpiolib drivers to the Wolfson entry
gpiolib: wm8994: Convert to devm_kzalloc()
gpiolib: wm8994: Use irq_domain mappings for gpios
gpio: add a driver for GPIO pins found on AMD-8111 south bridge chips
gpio/tca6424: merge I2C transactions, remove cast
gpio/of: fix a typo of comment message
Converting the gpio driver of tps6586x to a platform
driver in place of registering the gpio through core
driver.
The motivation of the change is:
- This is inline with the mfd drivers implementation.
- This will move the related gpio support to gpio driver
folder where all gpio related drivers are available.
This will be easy the maintenance and enhancement is
anything done for gpio.
- The gpio functionality can be selected through config
variable.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Arizona class devices provide some GPIOs for use in the system. This
driver provides support for these via gpiolib. Currently interrupts are
not supported, normally the GPIOs are outputs only.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[Fold in WM5110 support patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a driver to use GPIO pins available on several AMD south bridges
(currently only AMD 8111 is supported).
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The feature GPIO_MSM_V1 is only available on three SoCs. On all other MSM SoCs
the INT_GPIO_GROUP{1,2} is undeclared, but Kconfig does allow such
configurations. Therefore the produced configuration is valid, but does not
compile. The problem is fixed by adding the missing Kconfig constraints.
drivers/gpio/gpio-msm-v1.c: In function âmsm_init_gpioâ:
drivers/gpio/gpio-msm-v1.c:629:26: error: 'INT_GPIO_GROUP1' undeclared
drivers/gpio/gpio-msm-v1.c:630:26: error: 'INT_GPIO_GROUP2' undeclared
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull MIPS updates from Ralf Baechle:
"The whole series has been sitting in -next for quite a while with no
complaints. The last change to the series was before the weekend the
removal of an SPI patch which Grant - even though previously acked by
himself - appeared to raise objections. So I removed it until the
situation is clarified. Other than that all the patches have the acks
from their respective maintainers, all MIPS and x86 defconfigs are
building fine and I'm not aware of any problems introduced by this
series.
Among the key features for this patch series is a sizable patchset for
Lantiq which among other things introduces support for Lantiq's
flagship product, the FALCON SOC. It also means that the opensource
developers behind this patchset have overtaken Lantiq's competing
inhouse development team that was working behind closed doors.
Less noteworthy the ath79 patchset which adds support for a few more
chip variants, cleanups and fixes. Finally the usual dose of tweaking
of generic code."
Fix up trivial conflicts in arch/mips/lantiq/xway/gpio_{ebu,stp}.c where
printk spelling fixes clashed with file move and eventual removal of the
printk.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (81 commits)
MIPS: lantiq: remove orphaned code
MIPS: Remove all -Wall and almost all -Werror usage from arch/mips.
MIPS: lantiq: implement support for FALCON soc
MTD: MIPS: lantiq: verify that the NOR interface is available on falcon soc
MTD: MIPS: lantiq: implement OF support
watchdog: MIPS: lantiq: implement OF support and minor fixes
SERIAL: MIPS: lantiq: implement OF support
GPIO: MIPS: lantiq: convert gpio-stp-xway to OF
GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio
GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder
MIPS: pci: convert lantiq driver to OF
MIPS: lantiq: convert dma to platform driver
MIPS: lantiq: implement support for clkdev api
MIPS: lantiq: drop ltq_gpio_request() and gpio_to_irq()
OF: MIPS: lantiq: implement irq_domain support
OF: MIPS: lantiq: implement OF support
MIPS: lantiq: drop mips_machine support
OF: PCI: const usage needed by MIPS
MIPS: Cavium: Remove smp_reserve_lock.
MIPS: Move cache setup to setup_arch().
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Rh0r
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"Besides the usual cleanups, this one brings:
* Support for 5 new chipsets: Intel's ICH LPC and SCH Centerton,
ST-E's STAX211, Samsung's MAX77693 and TI's LM3533.
* Device tree support for the twl6040, tps65910, da9502 and ab8500
drivers.
* Fairly big tps56910, ab8500 and db8500 updates.
* i2c support for mc13xxx.
* Our regular update for the wm8xxx driver from Mark."
Fix up various conflicts with other trees, largely due to ab5500 removal
etc.
* tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (106 commits)
mfd: Fix build break of max77693 by adding REGMAP_I2C option
mfd: Fix twl6040 build failure
mfd: Fix max77693 build failure
mfd: ab8500-core should depend on MFD_DB8500_PRCMU
gpio: tps65910: dt: process gpio specific device node info
mfd: Remove the parsing of dt info for tps65910 gpio
mfd: Save device node parsed platform data for tps65910 sub devices
mfd: Add r_select to lm3533 platform data
gpio: Add Intel Centerton support to gpio-sch
mfd: Emulate active low IRQs as well as active high IRQs for wm831x
mfd: Mark two lm3533 zone registers as volatile
mfd: Fix return type of lm533 attribute is_visible
mfd: Enable Device Tree support in the ab8500-pwm driver
mfd: Enable Device Tree support in the ab8500-sysctrl driver
mfd: Add support for Device Tree to twl6040
mfd: Register the twl6040 child for the ASoC codec unconditionally
mfd: Allocate twl6040 IRQ numbers dynamically
mfd: twl6040 code cleanup in interrupt initialization part
mfd: Enable ab8500-gpadc driver for Device Tree
mfd: Prevent unassigned pointer from being used in ab8500-gpadc driver
...
Lots of gpio changes, both to core code and drivers. Changes do touch
architecture code to remove the need for separate arm/gpio.h includes
in most architectures. Some new drivers are added, and a number of
gpio drivers are converted to use irq_domains for gpio inputs used as
interrupts. Device tree support has been amended to allow multiple
gpio_chips to use the same device tree node. Remaining changes are
primarily bug fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPvpFBAAoJEEFnBt12D9kB50EP/0q2co+Ddlz4DWM07TLMgTw8
eCSi79+oB85RcE+0FlAo/SJu9VlYDKSLT3wMbIyycfJi3cUtOb+hay0j+wxcn4bz
G2qXj2Het5rX6hFI2tSCvJfDqMwU0wEygn9a6a/bw3VGSOIVmMTmRswrbbBcFzVu
8xobviN7LANLEZyhd4Ip5YfrcWH9ABmmhZX7ihn1AJubVL47xGo0uds9ZFX1sAKB
Zyr80+BeUK7mhZ74UUfQHtS+x24JD62OLM9eaQN0/BBAqBewQJlxhMakPbTGmcuO
Vy3CPmZiWw6tdVWgKvxE7cIXLI4YbB2B6w2TRJBBkFAlz4RsO2bFU/ibEv1vg9YE
oxAUelMj0INdY4iRT135fDJTIGauWon22Tqd2MVtun4r6fwcL0BgFYN6yCMtEqbx
bpYkKTi6tdyE7k2Ph+carCIuw9SwOk/4pm1xCWC0k6YdAnRE0zykCLvAuAabpmzs
i/H1jcp/F4KSYldEoDlGYG4lFZiISthxOy9l6/d4GrBj723attrmztolMfrpFLF6
XPTf7HODQFmZ6n7mBIjCg4hoqydAYyKcW7lROc7DKkEXIWOeeeA+EoTytkwPLLz5
CBLoZfDoqUT8xa2vv4MZ/+G9chSDi5vMryqEYi9tXMbVEZW31xqh6hxk0xPMcY13
qVAaRlcz49AQjWq/0vR4
=U6hj
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO driver changes from Grant Likely:
"Lots of gpio changes, both to core code and drivers.
Changes do touch architecture code to remove the need for separate
arm/gpio.h includes in most architectures.
Some new drivers are added, and a number of gpio drivers are converted
to use irq_domains for gpio inputs used as interrupts. Device tree
support has been amended to allow multiple gpio_chips to use the same
device tree node.
Remaining changes are primarily bug fixes."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (33 commits)
gpio/generic: initialize basic_mmio_gpio shadow variables properly
gpiolib: Remove 'const' from data argument of gpiochip_find()
gpio/rc5t583: add gpio driver for RICOH PMIC RC5T583
gpiolib: quiet gpiochip_add boot message noise
gpio: mpc8xxx: Prevent NULL pointer deref in demux handler
gpio/lpc32xx: Add device tree support
gpio: Adjust of_xlate API to support multiple GPIO chips
gpiolib: Implement devm_gpio_request_one()
gpio-mcp23s08: dbg_show: fix pullup configuration display
Add support for TCA6424A
gpio/omap: (re)fix wakeups on level-triggered GPIOs
gpio/omap: fix broken context restore for non-OFF mode transitions
gpio/omap: fix missing check in *_runtime_suspend()
gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()
gpio/omap: remove suspend/resume callbacks
gpio/omap: remove retrigger variable in gpio_irq_handler
gpio/omap: remove saved_wakeup field from struct gpio_bank
gpio/omap: remove suspend_wakeup field from struct gpio_bank
gpio/omap: remove saved_fallingdetect, saved_risingdetect
gpio/omap: remove virtual_irq_start variable
...
Conflicts:
drivers/gpio/gpio-samsung.c
This patch adds the Intel Centerton processor device ID for GPIO.
The device ID is defined in include/linux/pci_ids.h
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Move the 2 drivers from arch/mips/lantiq/xway/ to the subsystem and make them
buildable.
The following 2 patches will convert the drivers to OF.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3838/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PMIC device RC5T583 from RICOH supports 8 gpios.
Adding gpio driver for this device to access the pins
control through gpio library.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[grant.likely: slight cosmetic changes]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch is V2 of the Emma Mobile GPIO driver. This
driver is designed to be reusable between multiple SoCs
that share the same basic building block, but so far it
has only been used on Emma Mobile EV2.
Each driver instance handles 32 GPIOs with individually
maskable IRQs. The driver operates on two I/O memory
ranges and the 32 GPIOs are hooked up to two interrupts.
In the case of Emma Mobile EV2 this GPIO building block
is used as main external interrupt controller hooking up
159 GPIOS as 159 interrupts via 5 driver instances and
10 interrupts to the GIC and the Cortex-A9 Dual.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Rather than requiring architectures that use gpiolib but don't have any
need to define anything custom to copy an asm/gpio.h provide a Kconfig
symbol which architectures must select in order to include gpio.h and
for other architectures just provide the trivial implementation directly.
This makes it much easier to do gpiolib updates and is also a step towards
making gpiolib APIs available on every architecture.
For architectures with existing boilerplate code leave a stub header in
place which warns on direct inclusion of asm/gpio.h and includes
linux/gpio.h to catch code that's doing this. Direct inclusion of
asm/gpio.h has long been deprecated.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jonas Bonn <jonas@southpole.se>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add gpio support for Intel MSIC chips found in Intel Medfield platforms.
MSIC supports totally 24 GPIOs with 16 low voltage and 8 high voltage pins.
Driver uses MSIC mfd interface for MSIC access.
(Updated comment to indicate why locking is actually safe)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This introduces 128 gpio bits (for each PCI device installed) with
working interrupt support.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
irq_domain already provides a facility to translate from hardware IRQ
numbers to Linux IRQ numbers so use that instead of open-coding the logic
in the driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This driver works on many Intel chipsets, including the ICH6, ICH7,
ICH8, ICH9, ICH10, 3100, Series 5/3400 (Ibex Peak), Series 6/C200
(Cougar Point), and NM10 (Tiger Point).
Additional Intel chipsets should be easily supported if needed, eg the
ICH1-5, EP80579, etc.
Tested on QM67 (Cougar Point), QM57 (Ibex Peak), 3100 (Whitmore Lake),
and NM10 (Tiger Point).
Includes work from Jean Delvare:
- Resource leak removal during module load/unload
- GPIO API bit value enforcement
Also includes code cleanup from Guenter Roeck and Grant Likely.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The irqdomain api changed significantly in v3.4 which caused a build
failure for this driver.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Hans J. Koch <hjk@linutronix.de>
Cc: Torben Hohn <torbenh@linutronix.de>
The code in drivers/of/gpio.c isn't shared by any other subsystem since it
is all gpiolib specific. drivers/gpio is a better place to maintain these
functions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
The Kconfig description and help text doesn't list all of the devices
supported by this driver. This patch adds the PCA957x devices.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Primarily gpio device driver changes with some minor side effects
under arch/arm and arch/x86. Also includes a few core changes such as
explicitly supporting (electrical) open source and open drain outputs
and some help for parsing gpio devicetree properties.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=BSW8
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO changes for v3.4 from Grant Likely:
"Primarily gpio device driver changes with some minor side effects
under arch/arm and arch/x86. Also includes a few core changes such as
explicitly supporting (electrical) open source and open drain outputs
and some help for parsing gpio devicetree properties."
Fix up context conflict due to Laxman Dewangan adding sleep control for
the tps65910 driver separately for gpio's and regulators.
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
gpio/ep93xx: Remove unused inline function and useless pr_err message
gpio/sodaville: Mark broken due to core irqdomain migration
gpio/omap: fix redundant decoding of gpio offset
gpio/omap: fix incorrect update to context.irqenable1
gpio/omap: fix incorrect context restore logic in omap_gpio_runtime_*
gpio/omap: fix missing dataout context save in _set_gpio_dataout_reg
gpio/omap: fix _set_gpio_irqenable implementation
gpio/omap: fix trigger type to unsigned
gpio/omap: fix wakeup_en register update in _set_gpio_wakeup()
gpio: tegra: tegra_gpio_config shouldn't be __init
gpio/davinci: fix enabling unbanked GPIO IRQs
gpio/davinci: fix oops on unbanked gpio irq request
gpio/omap: Fix section warning for omap_mpuio_alloc_gc()
ARM: tegra: export tegra_gpio_{en,dis}able
gpio/gpio-stmpe: Fix the value returned by _get_value routine
Documentation/gpio.txt: Explain expected pinctrl interaction
GPIO: LPC32xx: Add output reading to GPO P3
GPIO: LPC32xx: Fix missing bit selection mask
gpio/omap: fix wakeups on level-triggered GPIOs
gpio/omap: Fix IRQ handling for SPARSE_IRQ
...
The sodaville driver doesn't build anymore due to the transition to
common irq_domain in the core code. It needs to be reworked, but
the rework isn't trivial. Since this is a new driver anyway for
v3.4, mark it as broken now and a fixup patch can re-enable it when
the rework change has been tested.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The GE GPIO driver provides basic support (set direction, read/write state)
for the GPIO provided on some GE single board computers. This patch moves
the driver from the 86xx specific platform directrory to the GPIO subsystem
so that it can be used on non-86xx boards.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Sodaville has GPIO controller behind the PCI bus. To my suprissed it is
not the same as on PXA.
The interrupt & gpio chip can be referenced from the device tree like
from any other driver. Unfortunately the driver which uses the gpio
interrupt has to use irq_of_parse_and_map() instead of
platform_get_irq(). The problem is that the platform device (which is
created from the device tree) is most likely created before the
interrupt chip is registered and therefore irq_of_parse_and_map() fails.
In theory the driver works as module. In reality most of the irq
functions are not exported to modules and it is possible that _this_
module is unloaded while the provided irqs are still in use.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
[torbenh@linutronix.de: make it work after the irq namespace cleanup,
add some device tree entries.]
Signed-off-by: Torben Hohn <torbenh@linutronix.de>
[bigeasy@linutronix.de: convert to generic irq & gpio chip]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[grant.likely@secretlab.ca: depend on x86 to avoid irq_domain breakage]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
we only use the gpio function of mc9s08dz60 mcu chip, so just
add the gpio driver, as this mcu will never be used in other board.
Signed-off-by: Wu Guoxing <b39297@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This driver does an unconditional read of io space during module init which
causes a bad dereference on ARM. It looks to me like this is an x86 only
drivers, so restrict it to only compile on x86.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Denis Turischev <denis@compulab.co.il>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (31 commits)
pinctrl: remove unnecessary max pin number
pinctrl: correct a offset while enumerating pins
pinctrl: some typo fixes
pinctrl: rename U300 and SIRF pin controllers
pinctrl: pass name instead of device to pin_config_*
pinctrl: add "struct seq_file;" to pinconf.h
pinctrl: conjure names for unnamed pins
pinctrl: add a group-specific hog macro
pinctrl: don't create a device for each pin controller
arm/u300: don't use PINMUX_MAP_PRIMARY*
pinctrl: implement PINMUX_MAP_SYS_HOG
pinctrl: add a pin config interface
pinctrl/coh901: driver to request its pins
pinctrl: u300-pinmux: register proper GPIO ranges
pinctrl: move the U300 GPIO driver to pinctrl
ARM: u300: localize GPIO assignments
pinctrl: make it possible to add multiple maps
pinctrl: make a copy of pinmux map
pinctrl: GPIO direction support for muxing
pinctrl: print pin range in GPIO range debugs
...
Mika Westerberg
Harini Katakam
Linus Walleij
Zhu, Lejun
Jean Delvare
Arnd Bergmann
Javier Martinez Canillas
Linus Torvalds
Alexander Shiyan
Geert Uytterhoeven
Alan Tull
Jamie Iles
Fabian Vogt
Kumar Gala
Aaron Sierra
Axel Lin
Milo Kim
Lars Poeschel
Baruch Siach
Grygorii Strashko
Bruno Randolf
Jonas Jensen
Rob Herring
Alexandre Courbot
Christian Ruppert
David Cohen
Markus Mayer
Ian Molton
Martin Schwidefsky
Simon Guinot
David Daney
Guenter Roeck
James Hogan
Tomasz Figa
Michal Simek
Olof Johansson
Rohit Vaswani
Andreas Larsson
Tony Prisk
Magnus Damm
Mathias Nyman
Heiko Carstens
Laxman Dewangan
Grant Likely
Shawn Guo
Kees Cook
Gregory CLEMENT
Vivien Didelot
Masanari Iida
Alessandro Rubini
Rafael J. Wysocki
Andrew Lunn
Shiraz Hashim
Thierry Reding
David S. Miller
Ashish Jangam
Thomas Petazzoni
Peter Ujfalusi
Axel Lin
Mark Brown
Dmitry Eremin-Solenikov
Christian Dietrich
Seth Heasley
John Crispin
Peter Tyser
Martyn Welch
Sebastian Andrzej Siewior
wu guoxing