Add notifier chain for changes in atm_dev.
Clients like br2684 will call register_atmdevice_notifier() to be notified of
changes. Drivers will call atm_dev_signal_change() to notify clients like
br2684 of the change.
On DSL and ATM devices it's usefull to have a know if you have a carrier
signal. netdevice LOWER_UP changes can be propagated to userspace via netlink
monitor.
Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides safety against negative optlen at the type
level instead of depending upon (sometimes non-trivial)
checks against this sprinkled all over the the place, in
each and every implementation.
Based upon work done by Arjan van de Ven and feedback
from Linus Torvalds.
Signed-off-by: David S. Miller <davem@davemloft.net>
We lack compat ioctl support through most of the ATM code. This patch
deals with most of it, and I can now at least use BR2684 and PPPoATM
with 32-bit userspace.
I haven't added a .compat_ioctl method to struct atm_ioctl, because
AFAICT none of the current users need any conversion -- so we can just
call the ->ioctl() method in every case. I looked at br2684, clip, lec,
mpc, pppoatm and atmtcp.
In svc_compat_ioctl() the only mangling which is needed is to change
COMPAT_ATM_ADDPARTY to ATM_ADDPARTY. Although it's defined as
_IOW('a', ATMIOC_SPECIAL+4,struct atm_iobuf)
it doesn't actually _take_ a struct atm_iobuf as an argument -- it takes
a struct sockaddr_atmsvc, which _is_ the same between 32-bit and 64-bit
code, so doesn't need conversion.
Almost all of vcc_ioctl() would have been identical, so I converted that
into a core do_vcc_ioctl() function with an 'int compat' argument.
I've done the same with atm_dev_ioctl(), where there _are_ a few
differences, but still it's relatively contained and there would
otherwise have been a lot of duplication.
I haven't done any of the actual device-specific ioctls, although I've
added a compat_ioctl method to struct atmdev_ops.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
linux/device.h header is not included in the David Woodhouse's
kernel-headers git tree which is used for userspace kernel headers. Which
results in compile errors when building iproute2. Attached patch moves
linux/device.h include under the #ifdef __KERNEL__ section.
Signed-off-by: Ismail Donmez <ismail@pardus.org.tr>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
atm_dev_deregister() removes device from atm_dev list immediately to
prevent operations on a phantom device. Decision to free device based
only on ->refcnt now. Remove shutdown_atm_dev() use atm_dev_deregister()
instead. atm_dev_deregister() also asynchronously releases all vccs
related to device.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Mitchell Blank Jr <mitch@sfgoth.com>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix implicit nocast warnings in atm code:
net/atm/atm_misc.c:35:44: warning: implicit cast to nocast type
drivers/atm/fore200e.c:183:33: warning: implicit cast to nocast type
Also use kzalloc() instead of kmalloc().
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!