Add shift capabilties for the frequency multiplier (DIV_SELECT) to
support Vybrid's USB PLL oddity. The PLL3 and PLL7 are the only
PLL control registers which have the DIV_SELECT bit shifted by
one. Be aware, there are known documentation errors in the
reference manual too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
ret variable is redundant. Call clk_pllv3_wait_lock() in the end
return.
Signed-off-by: Dmitry Voytik <voytikd@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since ENABLE and BYPASS bits of PLLs are now implemented as separate
gate and mux clocks by clock drivers, the code handling these two bits
can be removed from clk-pllv3 driver.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Currently, POWER and BYPASS bits are set up in a single write to pllv3
register. This causes problem occasionally from the IPU/HDMI testing.
Let's follow FSL BSP code to set up POWER bit, relock, and then BYPASS
sequentially.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The pllv3 nees relock not only when powering up but also when rate
changes. The patch creates a helper function clk_pllv3_wait_lock() and
moves the relock code from clk_pllv3_prepare() into there, so that
both .prepare() and .set_rate() hooks of pllv3 can call into the helper
for relocking.
Since relock is only needed when PLL is powered up while clk_set_rate()
could be called before clk is prepared, we need to add a check in
clk_pllv3_wait_lock() to skip the relock if PLL is not powered.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The pllv3 relock time varies in the range of 50us ~ 500us, depending on
the specific PLL type, e.g. 50us for ARM PLL and 450us for Audio/Video
PLL. Let's add a usleep_range() call instead of doing busy wait during
relock.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There are two improvements for this commit:
- Add comparing pll lock condition after while loop. It can
fix potential fake timeout problem caused by the code is just
scheduled out before compare the timeout, and the time of
scheduling out are more than one jiffies.
- Move timeout assignment more close to compare the timeout.
It can reduce the possibility the code is scheduled out, and
the timeout can be more precise.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
MLB PLL should be handled internally in MLB driver,
so remove it from pllv3.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Now that the additional enable bits in the enet PLL are handled
as gates, the gate_mask is identical for all plls. Remove the
gate_mask from the code and use the BM_PLL_ENABLE bit for
enabling/disabling the PLL.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
In current code the ethernet PLL is not handled correctly. The PLL runs at 500MHz
and has different outputs. Only the enet reference clock is implemented. This
patch changes the PLL so that it outputs 500MHz and adds the additional outputs
as dividers. This now matches the datasheet which says:
> This PLL synthesizes a low jitter clock from 24 MHz reference clock.
> The PLL outputs a 500 MHz clock. The reference clocks generated by this PLL are:
> • Ref_PCIe = 125 MHz
> • Ref_SATA = 100 MHz
> • Ref_ethernet, which is configurable based on the PLL_ENET[1:0] register field.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Stefan Agner
Dmitry Voytik
Shawn Guo
Shawn Guo
Peter Chen
Jiada Wang
Sascha Hauer