This reverts commit 40f11adc7c.
Jens found that iwlwifi firmware loading failed on a Lenovo X1 Carbon,
gen4:
iwlwifi 0000:04:00.0: Direct firmware load for iwlwifi-8000C-34.ucode failed with error -2
iwlwifi 0000:04:00.0: Direct firmware load for iwlwifi-8000C-33.ucode failed with error -2
iwlwifi 0000:04:00.0: Direct firmware load for iwlwifi-8000C-32.ucode failed with error -2
iwlwifi 0000:04:00.0: loaded firmware version 31.532993.0 op_mode iwlmvm
iwlwifi 0000:04:00.0: Detected Intel(R) Dual Band Wireless AC 8260, REV=0x208
...
iwlwifi 0000:04:00.0: Failed to load firmware chunk!
iwlwifi 0000:04:00.0: Could not load the [0] uCode section
iwlwifi 0000:04:00.0: Failed to start INIT ucode: -110
iwlwifi 0000:04:00.0: Failed to run INIT ucode: -110
He bisected it to 40f11adc7c ("PCI: Avoid race while enabling upstream
bridges"). Revert that commit to fix the regression.
Link: http://lkml.kernel.org/r/4bcbcbc1-7c79-09f0-5071-bc2f53bf6574@kernel.dk
Fixes: 40f11adc7c ("PCI: Avoid race while enabling upstream bridges")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Srinath Mannam <srinath.mannam@broadcom.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Luca Coelho <luca@coelho.fi>
CC: Johannes Berg <johannes@sipsolutions.net>
CC: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9cLP
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add enhanced Downstream Port Containment support, which prints more
details about Root Port Programmed I/O errors (Dongdong Liu)
- add Layerscape ls1088a and ls2088a support (Hou Zhiqiang)
- add MediaTek MT2712 and MT7622 support (Ryder Lee)
- add MediaTek MT2712 and MT7622 MSI support (Honghui Zhang)
- add Qualcom IPQ8074 support (Varadarajan Narayanan)
- add R-Car r8a7743/5 device tree support (Biju Das)
- add Rockchip per-lane PHY support for better power management (Shawn
Lin)
- fix IRQ mapping for hot-added devices by replacing the
pci_fixup_irqs() boot-time design with a host bridge hook called at
probe-time (Lorenzo Pieralisi, Matthew Minter)
- fix race when enabling two devices that results in upstream bridge
not being enabled correctly (Srinath Mannam)
- fix pciehp power fault infinite loop (Keith Busch)
- fix SHPC bridge MSI hotplug events by enabling bus mastering
(Aleksandr Bezzubikov)
- fix a VFIO issue by correcting PCIe capability sizes (Alex
Williamson)
- fix an INTD issue on Xilinx and possibly other drivers by unifying
INTx IRQ domain support (Paul Burton)
- avoid IOMMU stalls by marking AMD Stoney GPU ATS as broken (Joerg
Roedel)
- allow APM X-Gene device assignment to guests by adding an ACS quirk
(Feng Kan)
- fix driver crashes by disabling Extended Tags on Broadcom HT2100
(Extended Tags support is required for PCIe Receivers but not
Requesters, and we now enable them by default when Requesters support
them) (Sinan Kaya)
- fix MSIs for devices that use phantom RIDs for DMA by assuming MSIs
use the real Requester ID (not a phantom RID) (Robin Murphy)
- prevent assignment of Intel VMD children to guests (which may be
supported eventually, but isn't yet) by not associating an IOMMU with
them (Jon Derrick)
- fix Intel VMD suspend/resume by releasing IRQs on suspend (Scott
Bauer)
- fix a Function-Level Reset issue with Intel 750 NVMe by waiting
longer (up to 60sec instead of 1sec) for device to become ready
(Sinan Kaya)
- fix a Function-Level Reset issue on iProc Stingray by working around
hardware defects in the CRS implementation (Oza Pawandeep)
- fix an issue with Intel NVMe P3700 after an iProc reset by adding a
delay during shutdown (Oza Pawandeep)
- fix a Microsoft Hyper-V lockdep issue by polling instead of blocking
in compose_msi_msg() (Stephen Hemminger)
- fix a wireless LAN driver timeout by clearing DesignWare MSI
interrupt status after it is handled, not before (Faiz Abbas)
- fix DesignWare ATU enable checking (Jisheng Zhang)
- reduce Layerscape dependencies on the bootloader by doing more
initialization in the driver (Hou Zhiqiang)
- improve Intel VMD performance allowing allocation of more IRQ vectors
than present CPUs (Keith Busch)
- improve endpoint framework support for initial DMA mask, different
BAR sizes, configurable page sizes, MSI, test driver, etc (Kishon
Vijay Abraham I, Stan Drozd)
- rework CRS support to add periodic messages while we poll during
enumeration and after Function-Level Reset and prepare for possible
other uses of CRS (Sinan Kaya)
- clean up Root Port AER handling by removing unnecessary code and
moving error handler methods to struct pcie_port_service_driver
(Christoph Hellwig)
- clean up error handling paths in various drivers (Bjorn Andersson,
Fabio Estevam, Gustavo A. R. Silva, Harunobu Kurokawa, Jeffy Chen,
Lorenzo Pieralisi, Sergei Shtylyov)
- clean up SR-IOV resource handling by disabling VF decoding before
updating the corresponding resource structs (Gavin Shan)
- clean up DesignWare-based drivers by unifying quirks to update Class
Code and Interrupt Pin and related handling of write-protected
registers (Hou Zhiqiang)
- clean up by adding empty generic pcibios_align_resource() and
pcibios_fixup_bus() and removing empty arch-specific implementations
(Palmer Dabbelt)
- request exclusive reset control for several drivers to allow cleanup
elsewhere (Philipp Zabel)
- constify various structures (Arvind Yadav, Bhumika Goyal)
- convert from full_name() to %pOF (Rob Herring)
- remove unused variables from iProc, HiSi, Altera, Keystone (Shawn
Lin)
* tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (170 commits)
PCI: xgene: Clean up whitespace
PCI: xgene: Define XGENE_PCI_EXP_CAP and use generic PCI_EXP_RTCTL offset
PCI: xgene: Fix platform_get_irq() error handling
PCI: xilinx-nwl: Fix platform_get_irq() error handling
PCI: rockchip: Fix platform_get_irq() error handling
PCI: altera: Fix platform_get_irq() error handling
PCI: spear13xx: Fix platform_get_irq() error handling
PCI: artpec6: Fix platform_get_irq() error handling
PCI: armada8k: Fix platform_get_irq() error handling
PCI: dra7xx: Fix platform_get_irq() error handling
PCI: exynos: Fix platform_get_irq() error handling
PCI: iproc: Clean up whitespace
PCI: iproc: Rename PCI_EXP_CAP to IPROC_PCI_EXP_CAP
PCI: iproc: Add 500ms delay during device shutdown
PCI: Fix typos and whitespace errors
PCI: Remove unused "res" variable from pci_resource_io()
PCI: Correct kernel-doc of pci_vpd_srdt_size(), pci_vpd_srdt_tag()
PCI/AER: Reformat AER register definitions
iommu/vt-d: Prevent VMD child devices from being remapping targets
x86/PCI: Use is_vmd() rather than relying on the domain number
...
Sporadic reset issues have been observed with an Intel 750 NVMe drive while
assigning the physical function to the guest machine. The sequence of
events observed is as follows:
- perform a Function Level Reset (FLR)
- sleep up to 1000ms total
- read ~0 from PCI_COMMAND (CRS completion for config read)
- warn that the device didn't return from FLR
- touch the device before it's ready
- device drops config writes when we restore register settings (there's
no mechanism for software to learn about CRS completions for writes)
- incomplete register restore leaves device in inconsistent state
- device probe fails because device is in inconsistent state
After reset, an endpoint may respond to config requests with Configuration
Request Retry Status (CRS) to indicate that it is not ready to accept new
requests. See PCIe r3.1, sec 2.3.1 and 6.6.2.
Increase the timeout value from 1 second to 60 seconds to cover the period
where device responds with CRS and also report polling progress.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: include the mandatory 100ms in the delays we print]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that we have a custom printf format specifier, convert users of
full_name() to use %pOF instead. This is preparation for removing storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
When we enable a device, we first enable any upstream bridges. If a bridge
has multiple downstream devices and we enable them simultaneously, the race
to enable the upstream bridge may cause problems. Consider this hierarchy:
bridge A --+-- device B
+-- device C
If drivers for B and C call pci_enable_device() simultaneously, both will
attempt to enable A, which involves setting PCI_COMMAND_MASTER via
pci_set_master() and PCI_COMMAND_MEMORY via pci_enable_resources().
In the following sequence, B's update to set A's PCI_COMMAND_MEMORY is
lost, and neither B nor C will work correctly:
B C
pci_set_master(A)
cmd = read(A, PCI_COMMAND)
cmd |= PCI_COMMAND_MASTER
pci_set_master(A)
cmd = read(A, PCI_COMMAND)
cmd |= PCI_COMMAND_MASTER
write(A, PCI_COMMAND, cmd)
pci_enable_device(A)
pci_enable_resources(A)
cmd = read(A, PCI_COMMAND)
cmd |= PCI_COMMAND_MEMORY
write(A, PCI_COMMAND, cmd)
write(A, PCI_COMMAND, cmd)
Avoid this race by holding a new pci_bridge_mutex while enabling a bridge.
This ensures that both PCI_COMMAND_MASTER and PCI_COMMAND_MEMORY will be
updated before another thread can start enabling the bridge.
Note that although pci_enable_bridge() is recursive, it enables any
upstream bridges *before* acquiring the mutex. When it acquires the mutex
and calls pci_set_master() and pci_enable_device(), any upstream bridges
have already been enabled so pci_enable_device() will not deadlock by
calling pci_enable_bridge() again.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
[bhelgaas: changelog, comment]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the pci_find_pcie_root_port() function is called on a root port
itself, return the root port rather than NULL.
This effectively reverts commit 0e40523287 ("PCI: fix oops when
try to find Root Port for a PCI device") which added an extra check
that would now be redundant.
Fixes: a99b646afa ("PCI: Disable PCIe Relaxed Ordering if unsupported")
Fixes: c56d4450eb ("PCI: Turn off Request Attributes to avoid Chelsio T5 Completion erratum")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix TCP checksum offload handling in iwlwifi driver, from Emmanuel
Grumbach.
2) In ksz DSA tagging code, free SKB if skb_put_padto() fails. From
Vivien Didelot.
3) Fix two regressions with bonding on wireless, from Andreas Born.
4) Fix build when busypoll is disabled, from Daniel Borkmann.
5) Fix copy_linear_skb() wrt. SO_PEEK_OFF, from Eric Dumazet.
6) Set SKB cached route properly in inet_rtm_getroute(), from Florian
Westphal.
7) Fix PCI-E relaxed ordering handling in cxgb4 driver, from Ding
Tianhong.
8) Fix module refcnt leak in ULP code, from Sabrina Dubroca.
9) Fix use of GFP_KERNEL in atomic contexts in AF_KEY code, from Eric
Dumazet.
10) Need to purge socket write queue in dccp_destroy_sock(), also from
Eric Dumazet.
11) Make bpf_trace_printk() work properly on 32-bit architectures, from
Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
bpf: fix bpf_trace_printk on 32 bit archs
PCI: fix oops when try to find Root Port for a PCI device
sfc: don't try and read ef10 data on non-ef10 NIC
net_sched: remove warning from qdisc_hash_add
net_sched/sfq: update hierarchical backlog when drop packet
net_sched: reset pointers to tcf blocks in classful qdiscs' destructors
ipv4: fix NULL dereference in free_fib_info_rcu()
net: Fix a typo in comment about sock flags.
ipv6: fix NULL dereference in ip6_route_dev_notify()
tcp: fix possible deadlock in TCP stack vs BPF filter
dccp: purge write queue in dccp_destroy_sock()
udp: fix linear skb reception with PEEK_OFF
ipv6: release rt6->rt6i_idev properly during ifdown
af_key: do not use GFP_KERNEL in atomic contexts
tcp: ulp: avoid module refcnt leak in tcp_set_ulp
net/cxgb4vf: Use new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag
net/cxgb4: Use new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag
PCI: Disable Relaxed Ordering Attributes for AMD A1100
PCI: Disable Relaxed Ordering for some Intel processors
PCI: Disable PCIe Relaxed Ordering if unsupported
...
Add two reasons for returning 0 value to the description of
pci_set_power_state() to include the cases when:
- the transition is to D1 or D2 but D1 and D2 are not supported
- the transition is to D3 but D3 is not supported
Signed-off-by: Piotr Gregor <piotrgregor@rsyncme.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The implementation of PCI workarounds may require that the device is reset
from its probe function. This implies that the PCI device lock is already
held, and makes calling pci_reset_function() impossible (since it will
itself try to take that lock).
Add pci_reset_function_locked(), which is the equivalent of
pci_reset_function(), except that it requires the PCI device lock to be
already held by the caller.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[bhelgaas: folded in fix for conflict with 52354b9d1f ("PCI: Remove
__pci_dev_reset() and pci_dev_reset()")]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # 4.11: 52354b9d1f46: PCI: Remove __pci_dev_reset() and pci_dev_reset()
Cc: stable@vger.kernel.org # 4.11
PCI bridges only have a reason to generate wakeup signals on behalf
of devices below them, so avoid preparing bridges for wakeup directly
in pci_enable_wake().
Also drop the pci_has_subordinate() check from pci_pm_default_resume()
as this will be done by pci_enable_wake() itself now.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Commit dc15e71eef (PCI / PM: Restore PME Enable if skipping wakeup
setup) introduced a mechanism by which the PME Enable bit can be
restored by pci_enable_wake() if dev->wakeup_prepared is set in
case it has been overwritten by PCI config space restoration.
However, that commit overlooked the fact that on some systems (Dell
XPS13 9360 in particular) the AML handling wakeup events checks PME
Status and PME Enable and it won't trigger a Notify() for devices
where those bits are not set while it is running.
That happens during resume from suspend-to-idle when pci_restore_state()
invoked by pci_pm_default_resume_early() clears PME Enable before the
wakeup events are processed by AML, effectively causing those wakeup
events to be ignored.
Fix this issue by restoring the PME Enable configuration right after
pci_restore_state() has been called instead of doing that in
pci_enable_wake().
Fixes: dc15e71eef (PCI / PM: Restore PME Enable if skipping wakeup setup)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/virtualization:
PCI: Remove __pci_dev_reset() and pci_dev_reset()
PCI: Split ->reset_notify() method into ->reset_prepare() and ->reset_done()
PCI: Protect pci_error_handlers->reset_notify() usage with device_lock()
PCI: Protect pci_driver->sriov_configure() usage with device_lock()
PCI: Mark Intel XXV710 NIC INTx masking as broken
PCI: Restore PRI and PASID state after Function-Level Reset
PCI: Cache PRI and PASID bits in pci_dev
The pci_error_handlers->reset_notify() method had a flag to indicate
whether to prepare for or clean up after a reset. The prepare and done
cases have no shared functionality whatsoever, so split them into separate
methods.
[bhelgaas: changelog, update locking comments]
Link: http://lkml.kernel.org/r/20170601111039.8913-3-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/resource:
PCI: Work around poweroff & suspend-to-RAM issue on Macbook Pro 11
PCI: Do not disregard parent resources starting at 0x0
Conflicts:
arch/x86/pci/fixup.c
* pci/pm:
PCI/PM: Avoid using device_may_wakeup() for runtime PM
x86/PCI: Avoid AMD SB7xx EHCI USB wakeup defect
PCI/PM: Restore the status of PCI devices across hibernation
drm/radeon: make MacBook Pro d3_delay quirk more generic
drm/amdgpu: remove unnecessary save/restore of pdev->d3_delay
PCI/PM: Add needs_resume flag to avoid suspend complete optimization
PCI: imx6: Fix config read timeout handling
switchtec: Fix minor bug with partition ID register
switchtec: Use new cdev_device_add() helper function
PCI: endpoint: Make PCI_ENDPOINT depend on HAS_DMA
pci_target_state() calls device_may_wakeup() which checks whether or not
the device may wake up the system from sleep states, but pci_target_state()
is used for runtime PM too.
Since runtime PM is expected to always enable remote wakeup if possible,
modify pci_target_state() to take additional argument indicating whether or
not it should look for a state from which the device can signal wakeup and
pass either the return value of device_can_wakeup(), or "false" (if the
device itself is not wakeup-capable) to it from the code related to runtime
PM.
While at it, fix the comment in pci_dev_run_wake() which is not about sleep
states.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The run_wake flag in struct dev_pm_info is used to indicate whether
or not the device is capable of generating remote wakeup signals at
run time (or in the system working state), but the distinction
between runtime remote wakeup and system wakeup signaling has always
been rather artificial. The only practical reason for it to exist
at the core level was that ACPI and PCI treated those two cases
differently, but that's not the case any more after recent changes.
For this reason, get rid of the run_wake flag and, when applicable,
use device_set_wakeup_capable() and device_can_wakeup() instead of
device_set_run_wake() and device_run_wake(), respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
After previous changes it is not necessary to distinguish between
device wakeup for run time and device wakeup from system sleep states
any more, so rework the PCI device wakeup settings code accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The test for INTx masking via PCI_COMMAND_INTX_DISABLE performed in
pci_intx_mask_supported() should be done before the device can be used.
This is to avoid writing PCI_COMMAND while the driver owns the device, in
case that has any effect on MSI/MSI-X interrupts.
Move the content of pci_intx_mask_supported() to pci_intx_mask_broken() and
call it from pci_setup_device().
The test result can be queried at any time later using the same
pci_intx_mask_supported() interface as before (though with changed
implementation), so callers (uio, vfio) should be unaffected.
Signed-off-by: Piotr Gregor <piotrgregor@rsyncme.org>
[bhelgaas: changelog, remove quirk check, remove locking, move
dev->broken_intx_masking assignment to caller]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Every method in struct device_driver or structures derived from it like
struct pci_driver MUST provide exclusion vs the driver's ->remove() method,
usually by using device_lock().
Protect use of pci_error_handlers->reset_notify() by holding the device
lock while calling it.
Note:
- pci_dev_lock() calls device_lock() in addition to blocking user-space
config accesses.
- pci_err_handlers->reset_notify() is used inside
pci_dev_save_and_disable() and pci_dev_restore(). We could hold the
device lock directly in pci_reset_notify(), but we expand the region
since we have several calls following each other.
Without this, ->reset_notify() may race with ->remove() calls, which can be
easily triggered in NVMe.
[bhelgaas: changelog, add pci_reset_notify() comment]
[bhelgaas: fold in fix from Dan Carpenter <dan.carpenter@oracle.com>:
http://lkml.kernel.org/r/20170701135323.x5vaj4e2wcs2mcro@mwanda]
Link: http://lkml.kernel.org/r/20170601111039.8913-2-hch@lst.de
Reported-by: Rakesh Pandit <rakesh@tuxera.com>
Tested-by: Rakesh Pandit <rakesh@tuxera.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The wakeup_prepared PCI device flag is used for preventing subsequent
changes of PCI device wakeup settings in the same way (e.g. enabling
device wakeup twice in a row).
However, in some cases PME Enable may be updated by things like PCI
configuration space restoration in the meantime and it may need to be
set again even though the rest of the settings need not change, so
modify __pci_enable_wake() to do that when it is about to return
early.
Also, it is reasonable to expect that __pci_enable_wake() will always
clear PME Status when invoked to disable device wakeup, so make it do
so even if it is going to return early then.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
After a Function-Level Reset, PCI states need to be restored. Save PASID
features and PRI reqs cached.
[bhelgaas: search for capability only if PRI/PASID were enabled]
Signed-off-by: CQ Tang <cq.tang@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Jean-Phillipe Brucker <jean-philippe.brucker@arm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Some drivers - like i915 - may not support the system suspend direct
complete optimization due to differences in their runtime and system
suspend sequence. Add a flag that when set resumes the device before
calling the driver's system suspend handlers which effectively disables
the optimization.
Needed by a future patch fixing suspend/resume on i915.
Suggested by Rafael.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org
Commit f44116ae88 ("PCI: Remove pci_find_parent_resource() use for
allocation") updated the logic that iterates over all bus resources and
compares them to a given resource, in order to decide whether one is the
parent of the latter.
This change inadvertently causes pci_find_parent_resource() to disregard
resources starting at address 0x0, resulting in an error such as the one
below on ARM systems whose I/O window starts at 0x0.
pci_bus 0000:00: root bus resource [mem 0x10000000-0x3efeffff window]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff window]
pci_bus 0000:00: root bus resource [mem 0x8000000000-0xffffffffff window]
pci_bus 0000:00: root bus resource [bus 00-0f]
pci 0000:00:01.0: PCI bridge to [bus 01]
pci 0000:00:02.0: PCI bridge to [bus 02]
pci 0000:00:03.0: PCI bridge to [bus 03]
pci 0000:00:03.0: can't claim BAR 13 [io 0x0000-0x0fff]: no compatible bridge window
pci 0000:03:01.0: can't claim BAR 0 [io 0x0000-0x001f]: no compatible bridge window
While this never happens on x86, it is perfectly legal in general for a PCI
MMIO or IO window to start at address 0x0, and it was supported in the code
before commit f44116ae88.
Drop the test for res->start != 0; resource_contains() already checks
whether [start, end) completely covers the resource, and so it should be
redundant.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/virtualization:
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: Call pcie_flr() from reset_chelsio_generic_dev()
PCI: Call pcie_flr() from reset_intel_82599_sfp_virtfn()
PCI: Export pcie_flr()
PCI: Add sysfs sriov_drivers_autoprobe to control VF driver binding
PCI: Avoid FLR for Intel 82579 NICs
Conflicts:
include/linux/pci.h
* pci/resource:
PCI: Don't resize resources when realigning all devices in system
PCI: Don't reassign resources that are already aligned
PCI: Factor pci_reassigndev_resource_alignment()
powerpc/powernv: Override pcibios_default_alignment() to force PCI devices to be page aligned
PCI: Add pcibios_default_alignment() for arch-specific alignment control
PCI: Fix calculation of bridge window's size and alignment
PCI: Ignore requested alignment for IOV BARs
PCI: Make PCI_ROM_ADDRESS_MASK a 32-bit constant
* pci/ioremap:
PCI: versatile: Update PCI config space remap function
PCI: keystone-dw: Update PCI config space remap function
PCI: layerscape: Update PCI config space remap function
PCI: hisi: Update PCI config space remap function
PCI: tegra: Update PCI config space remap function
PCI: xgene: Update PCI config space remap function
PCI: armada8k: Update PCI config space remap function
PCI: designware: Update PCI config space remap function
PCI: iproc-platform: Update PCI config space remap function
PCI: qcom: Update PCI config space remap function
PCI: rockchip: Update PCI config space remap function
PCI: spear13xx: Update PCI config space remap function
PCI: xilinx-nwl: Update PCI config space remap function
PCI: xilinx: Update PCI config space remap function
PCI: ECAM: Map config region with pci_remap_cfgspace()
PCI: Implement devm_pci_remap_cfgspace()
devres: fix devm_ioremap_*() offset parameter kerneldoc description
ARM: Implement pci_remap_cfgspace() interface
ARM64: Implement pci_remap_cfgspace() interface
linux/io.h: Add pci_remap_cfgspace() interface
PCI: Remove __weak tag from pci_remap_iospace()
The introduction of the pci_remap_cfgspace() interface allows PCI host
controller drivers to map PCI config space through a dedicated kernel
interface. Current PCI host controller drivers use the devm_ioremap_*()
devres interfaces to map PCI configuration space regions so in order to
update them to the new pci_remap_cfgspace() mapping interface a new set of
devres interfaces should be implemented so that PCI host controller drivers
can make use of them.
Introduce two new functions in the PCI kernel layer and Devres
documentation:
- devm_pci_remap_cfgspace()
- devm_pci_remap_cfg_resource()
so that PCI host controller drivers can make use of them to map PCI
configuration space regions.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
These are useful for PCIe host drivers, and those drivers can be modules.
[bhelgaas: don't remove __weak; it's removed elsewhere]
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Currently we opencode the FLR sequence in lots of place; export a core
helper instead. We split out the probing for FLR support as all the
non-core callers already know their hardware.
Note that in the new pci_has_flr() function the quirk check has been moved
before the capability check as there is no point in reading the capability
in this case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_remap_iospace() is marked as a weak symbol even though no architecture
is currently overriding it; given that its implementation internals have
already code paths that are arch specific (ie PCI_IOBASE and
ioremap_page_range() attributes) there is no need to leave the weak symbol
in the kernel since the same functionality can be achieved by customizing
per-arch the corresponding functionality.
Remove the __weak symbol from pci_remap_iospace().
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The "pci=resource_alignment" argument aligns BARs of designated devices by
artificially increasing their size. Increasing the size increases the
alignment and prevents other resources from being assigned in the same
alignment region, e.g., in the same page, but it can break drivers that use
the BAR size to locate things, e.g., ilo_map_device() does this:
off = pci_resource_len(pdev, bar) - 0x2000;
The new pcibios_default_alignment() interface allows an arch to request
that *all* BARs in the system be aligned to a larger size. In this case,
we don't need to artificially increase the resource size because we know
every BAR of every device will be realigned, so nothing will share the same
alignment region.
Use IORESOURCE_STARTALIGN to request realignment of PCI BARs when we know
we're realigning all BARs in the system.
[bhelgaas: comment, changelog]
Signed-off-by: Yongji Xie <elohimes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "pci=resource_alignment=" kernel argument designates devices for which
we want alignment greater than is required by the PCI specs. Previously we
set IORESOURCE_UNSET for every MEM resource of those devices, even if the
resource was *already* sufficiently aligned.
If a resource is already sufficiently aligned, leave it alone and don't try
to reassign it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull the BAR size adjustment out into a new function,
pci_request_resource_alignment(), and add a comment about how and why we
increase the resource size and alignment.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When VFIO passes through a PCI device to a guest, it does not allow the
guest to mmap BARs that are smaller than PAGE_SIZE unless it can reserve
the rest of the page (see vfio_pci_probe_mmaps()). This is because a page
might contain several small BARs for unrelated devices and a guest should
not be able to access all of them.
VFIO emulates guest accesses to non-mappable BARs, which is functional but
slow. On systems with large page sizes, e.g., PowerNV with 64K pages, BARs
are more likely to share a page and performance is more likely to be a
problem.
Add a weak function to set default alignment for all PCI devices. An arch
can override it to force the PCI core to place memory BARs on their own
pages.
Signed-off-by: Yongji Xie <elohimes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Laurent Pinchart reported that the Renesas R-Car H2 Lager board (r8a7790)
crashes during suspend tests. Geert Uytterhoeven managed to reproduce the
issue on an M2-W Koelsch board (r8a7791):
It occurs when the PME scan runs, once per second. During PME scan, the
PCI host bridge (rcar-pci) registers are accessed while its module clock
has already been disabled, leading to the crash.
One reproducer is to configure s2ram to use "s2idle" instead of "deep"
suspend:
# echo 0 > /sys/module/printk/parameters/console_suspend
# echo s2idle > /sys/power/mem_sleep
# echo mem > /sys/power/state
Another reproducer is to write either "platform" or "processors" to
/sys/power/pm_test. It does not (or is less likely) to happen during full
system suspend ("core" or "none") because system suspend also disables
timers, and thus the workqueue handling PME scans no longer runs. Geert
believes the issue may still happen in the small window between disabling
module clocks and disabling timers:
# echo 0 > /sys/module/printk/parameters/console_suspend
# echo platform > /sys/power/pm_test # Or "processors"
# echo mem > /sys/power/state
(Make sure CONFIG_PCI_RCAR_GEN2 and CONFIG_USB_OHCI_HCD_PCI are enabled.)
Rafael Wysocki agrees that PME scans should be suspended before the host
bridge registers become inaccessible. To that end, queue the task on a
workqueue that gets frozen before devices suspend.
Rafael notes however that as a result, some wakeup events may be missed if
they are delivered via PME from a device without working IRQ (which hence
must be polled) and occur after the workqueue has been frozen. If that
turns out to be an issue in practice, it may be possible to solve it by
calling pci_pme_list_scan() once directly from one of the host bridge's
pm_ops callbacks.
Stacktrace for posterity:
PM: Syncing filesystems ... [ 38.566237] done.
PM: Preparing system for sleep (mem)
Freezing user space processes ... [ 38.579813] (elapsed 0.001 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
PM: Suspending system (mem)
PM: suspend of devices complete after 152.456 msecs
PM: late suspend of devices complete after 2.809 msecs
PM: noirq suspend of devices complete after 29.863 msecs
suspend debug: Waiting for 5 second(s).
Unhandled fault: asynchronous external abort (0x1211) at 0x00000000
pgd = c0003000
[00000000] *pgd=80000040004003, *pmd=00000000
Internal error: : 1211 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted
4.9.0-rc1-koelsch-00011-g68db9bc814362e7f #3383
Hardware name: Generic R8A7791 (Flattened Device Tree)
Workqueue: events pci_pme_list_scan
task: eb56e140 task.stack: eb58e000
PC is at pci_generic_config_read+0x64/0x6c
LR is at rcar_pci_cfg_base+0x64/0x84
pc : [<c041d7b4>] lr : [<c04309a0>] psr: 600d0093
sp : eb58fe98 ip : c041d750 fp : 00000008
r10: c0e2283c r9 : 00000000 r8 : 600d0013
r7 : 00000008 r6 : eb58fed6 r5 : 00000002 r4 : eb58feb4
r3 : 00000000 r2 : 00000044 r1 : 00000008 r0 : 00000000
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
Control: 30c5387d Table: 6a9f6c80 DAC: 55555555
Process kworker/1:1 (pid: 20, stack limit = 0xeb58e210)
Stack: (0xeb58fe98 to 0xeb590000)
fe80: 00000002 00000044
fea0: eb6f5800 c041d9b0 eb58feb4 00000008 00000044 00000000 eb78a000 eb78a000
fec0: 00000044 00000000 eb9aff00 c0424bf0 eb78a000 00000000 eb78a000 c0e22830
fee0: ea8a6fc0 c0424c5c eaae79c0 c0424ce0 eb55f380 c0e22838 eb9a9800 c0235fbc
ff00: eb55f380 c0e22838 eb55f380 eb9a9800 eb9a9800 eb58e000 eb9a9824 c0e02100
ff20: eb55f398 c02366c4 eb56e140 eb5631c0 00000000 eb55f380 c023641c 00000000
ff40: 00000000 00000000 00000000 c023a928 cd105598 00000000 40506a34 eb55f380
ff60: 00000000 00000000 dead4ead ffffffff ffffffff eb58ff74 eb58ff74 00000000
ff80: 00000000 dead4ead ffffffff ffffffff eb58ff90 eb58ff90 eb58ffac eb5631c0
ffa0: c023a844 00000000 00000000 c0206d68 00000000 00000000 00000000 00000000
ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 3a81336c 10ccd1dd
[<c041d7b4>] (pci_generic_config_read) from [<c041d9b0>]
(pci_bus_read_config_word+0x58/0x80)
[<c041d9b0>] (pci_bus_read_config_word) from [<c0424bf0>]
(pci_check_pme_status+0x34/0x78)
[<c0424bf0>] (pci_check_pme_status) from [<c0424c5c>] (pci_pme_wakeup+0x28/0x54)
[<c0424c5c>] (pci_pme_wakeup) from [<c0424ce0>] (pci_pme_list_scan+0x58/0xb4)
[<c0424ce0>] (pci_pme_list_scan) from [<c0235fbc>]
(process_one_work+0x1bc/0x308)
[<c0235fbc>] (process_one_work) from [<c02366c4>] (worker_thread+0x2a8/0x3e0)
[<c02366c4>] (worker_thread) from [<c023a928>] (kthread+0xe4/0xfc)
[<c023a928>] (kthread) from [<c0206d68>] (ret_from_fork+0x14/0x2c)
Code: ea000000 e5903000 f57ff04f e3a00000 (e5843000)
---[ end trace 667d43ba3aa9e589 ]---
Fixes: df17e62e5b ("PCI: Add support for polling PME state on suspended legacy PCI devices")
Reported-and-tested-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reported-and-tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org # 2.6.37+
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
We would call pci_reassigndev_resource_alignment() before
pci_init_capabilities(). So the requested alignment would never work for
IOV BARs.
Furthermore, it's meaningless to request additional alignment for IOV BARs,
the IOV BAR alignment is only determined by the VF BAR size.
Signed-off-by: Yongji Xie <xyjxie@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Per Intel Specification Update 335553-002 (see link below), some 82579
network adapters advertise a Function Level Reset (FLR) capability, but
they can hang when an FLR is triggered.
To reproduce the problem, attach the device to a VM, then detach and try to
attach again.
Add a quirk to prevent the use of FLR on these devices.
[bhelgaas: changelog, comments]
Link: http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/82579lm-82579v-gigabit-network-connection-spec-update.pdf
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the PCI device is disconnected, return false immediately from
pci_device_is_present(). pci_device_is_present() uses the bus accessors,
so the early return in the device accessors doesn't help here.
Tested-by: Krishna Dhulipala <krishnad@fb.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Wei Zhang <wzhang@fb.com>
msleep() still sleeps 1 jiffy even when told to sleep for zero
milliseconds. That can end up being 1-2 milliseconds or more. In the
cases of d3_delay and d3cold_delay, that unnecessarily increases suspend
and/or resume latencies.
Do not sleep at all for the respective cases if d3_delay is zero or
d3cold_delay is zero.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Bjorn Helgaas
Linus Torvalds
Rafael J. Wysocki
Sinan Kaya
Rob Herring
Srinath Mannam
Thierry Reding
dingtianhong
Piotr Gregor
Marc Zyngier
Christoph Hellwig
CQ Tang
Imre Deak
Ard Biesheuvel
Lorenzo Pieralisi
Brian Norris
Yongji Xie
Lukas Wunner
Yongji Xie
Sasha Neftin
Keith Busch
Adrian Hunter