Comment was not updated when tty_insert_flip_string was generalised.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CC drivers/char/tty_buffer.o
drivers/char/tty_buffer.c: In function ‘tty_insert_flip_string_fixed_flag’:
drivers/char/tty_buffer.c:251: warning: comparison of distinct pointer types lacks a cast
drivers/char/tty_buffer.c: In function ‘tty_insert_flip_string_flags’:
drivers/char/tty_buffer.c:288: warning: comparison of distinct pointer types lacks a cast
Fix it by replacing min() with min_t() in tty_insert_flip_string_flags and
tty_insert_flip_string_fixed_flag().
Signed-off-by: Fang Wenqi <antonf@turbolinux.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (220 commits)
USB: backlight, appledisplay: fix incomplete registration failure handling
USB: pl2303: remove unnecessary reset of usb_device in urbs
USB: ftdi_sio: remove obsolete check in unthrottle
USB: ftdi_sio: remove unused tx_bytes counter
USB: qcaux: driver for auxiliary serial ports on Qualcomm devices
USB: pl2303: initial TIOCGSERIAL support
USB: option: add Longcheer/Longsung vendor ID
USB: fix I2C API usage in ohci-pnx4008.
USB: usbmon: mask seconds properly in text API
USB: sisusbvga: no unnecessary GFP_ATOMIC
USB: storage: onetouch: unnecessary GFP_ATOMIC
USB: serial: ftdi: add CONTEC vendor and product id
USB: remove references to port->port.count from the serial drivers
USB: tty: Prune uses of tty_request_room in the USB layer
USB: tty: Add a function to insert a string of characters with the same flag
USB: don't read past config->interface[] if usb_control_msg() fails in usb_reset_configuration()
USB: tty: kill request_room for USB ACM class
USB: tty: sort out the request_room handling for whiteheat
USB: storage: fix misplaced parenthesis
USB: vstusb.c: removal of driver for Vernier Software & Technology, Inc., devices and spectrometers
...
The USB drivers often want to insert a series of bytes all with the same
flag set - provide a helper for this case.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We allocate during interrupts so while our buffering is normally diced up
small anyway on some hardware at speed we can pressure the VM excessively
for page pairs. We don't really need big buffers to be linear so don't try
so hard.
In order to make this work well we will tidy up excess callers to request_room,
which cannot itself enforce this break up.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This way all flush_to_ldisc work is always done through the workqueues,
and we thus have a single point of serialization.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We really don't want to mark the pty as a low-latency device, because as
Alan points out, the ->write method can be called from an IRQ (ppp?),
and that means we can't use ->low_latency=1 as we take mutexes in the
low_latency case.
So rather than using low_latency to force the written data to be pushed
to the ldisc handling at 'write()' time, just make the reader side (or
the poll function) do the flush when it checks whether there is data to
be had.
This also fixes the problem with lost data in an emacs compile buffer
(bugzilla 13815), and we can thus revert the low_latency pty hack
(commit 3a54297478e6578f96fd54bf4daa1751130aca86: "pty: quickfix for the
pty ENXIO timing problems").
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[ Modified to do the tty_flush_to_ldisc() inside input_available_p() so
that it triggers for both read and poll() - Linus]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The two are basically independent chunks of code so lets split them up for
readability and sanity. It also makes the API boundaries much clearer.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>