If we've just created an interface and the an rport is
logging in we may have a request on the wire (say PRLI).
If we destroy the interface, we'll go through each rport
on the disc->rports list and set each rport's state to NONE.
Then the lport will reset the EM. The EM reset will send a
CLOSED event to the prli_resp() handler which will notice
that the state != PRLI. In this case it frees the frame
pointer, decrements the refcount and unlocks the rport.
The problem is that there isn't a frame in this case. It's
just a pointer with an embedded error code. The free causes
an Oops.
This patch moves the error checking to be before the state
checking.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Just rename the variable as per our naming convention.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We only need to use this macro when assigning a value to
rport->dd_data. All other accesses should just use dd_data.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When a sequence cannot be delivered to the target, the local
port will schedule retries, While this process is in progress,
if we destroy the FCoE interface, the fcoe_sw_destroy routine is
entered, and the fc_exch_mgr_free(lp->emp) is called. Thus
if fc_exch_alloc() is called when retrying the sequence,
the mempool_alloc() will fail to allocate the exchange because
the mempool of the exchange manager has already been released.
This patch is to cancel any pending retry work of the local
port before we start to destroy the interface.
Also, when resetting the local port, we should also stop the
scheduled pending retries.
Signed-off-by: Steve Ma <steve.ma@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The fc_fcp_complete_locked detected data underrun in this case and set
the FC_DATA_UNDRUN but that was ignored by fc_io_compl for all cases
including read underrun.
Added code to not to ignore FC_DATA_UNDRUN for read IO and instead
suggested scsi-ml to retry cmd to recover from lost data frame.
Not sure if it is okay to ignore FC_DATA_UNDRUN for other case, so let
code as is for other cases but removed or-ing with zero valued fsp->cdb_status
for those cases.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This allows any rport ELS to retry on LS_RJT.
The rport error handling would only retry on resource allocation failures
and exchange timeouts. I have a target that will occasionally reject PLOGI
when we do a quick LOGO/PLOGI. When a critical ELS was rejected, libfc would
fail silently leaving the rport in a dead state.
The retry count and delay are managed by fc_rport_error_retry. If the retry
count is exceeded fc_rport_error will be called. When retrying is not the
correct course of action, fc_rport_error can be called directly.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The fcoe_xmit could call fc_pause in case the pending skb queue len is larger
than FCOE_MAX_QUEUE_DEPTH, the fc_pause was trying to grab lport->lp_muex to
change lport->link_status and that had these issues :-
1. The fcoe_xmit was getting called with bh disabled, thus causing
"BUG: scheduling while atomic" when grabbing lport->lp_muex with bh disabled.
2. fc_linkup and fc_linkdown function calls lport_enter function with
lport->lp_mutex held and these enter function in turn calls fcoe_xmit to send
lport related FC frame, e.g. fc_linkup => fc_lport_enter_flogi to send flogi
req. In this case grabbing the same lport->lp_mutex again in fc_puase from
fcoe_xmit would cause deadlock.
The lport->lp_mutex was used for setting FC_PAUSE in fcoe_xmit path but
FC_PAUSE bit was not used anywhere beside just setting and clear this
bit in lport->link_status, instead used a separate field qfull in fc_lport
to eliminate need for lport->lp_mutex to track pending queue full condition
and in turn avoid above described two locking issues.
Also added check for lp->qfull in fc_fcp_lport_queue_ready to trigger
SCSI_MLQUEUE_HOST_BUSY when lp->qfull is set to prevent more scsi-ml cmds
while lp->qfull is set.
This patch eliminated FC_LINK_UP and FC_PAUSE and instead used dedicated
fields in fc_lport for this, this simplified all related conditional
code.
Also removed fc_pause and fc_unpause functions and instead used newly added
lport->qfull directly in fcoe.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The fc_seq_start_next grabs ep->ex_lock but this lock was already held here,
so instead called fc_seq_start_next_locked to avoid soft lockup.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cleanup exchange held due to RRQ when RRQ exch times out, in this case the
ABTS is already done causing RRQ req therefore proceeding with cleanup in
fc_exch_rrq_resp should be okay to restore exch resource.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When a rport goes away, libFC does a plogi which will reset exchanges
at the rport. Clean exchanges at our end, both in transport and libFC.
If transport hooks into exch_mgr_reset, it will call back into
fc_exch_mgr_reset() to clean up libFC exchanges.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
fc_exch_mgr structure is private to fc_exch.c. To export exch_mgr_reset to
transport, transport needs access to the exch manager. Change
exch_mgr_reset to use lport param which is the shared structure between
libFC and transport.
Alternatively, fc_exch_mgr definition can be moved to libfc.h so that lport
can be accessed from mp*.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We currently try to spin up drives connected to standby and unavailable
ports. This will never succeed and wastes a lot of time. Fail quickly
if the sense data reports the port is in standby or unavailable state.
Reported-by: Narayanan Rengarajan <narayanan.rengarajan@hp.com>
Tested-by: Narayanan Rengarajan <narayanan.rengarajan@hp.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Instead of terminating after five retries, commands terminated by
ABORTED_COMMAND sense are retrying forever. The problem was
introduced by:
commit b60af5b0ad
Author: Alan Stern <stern@rowland.harvard.edu>
Date: Mon Nov 3 15:56:47 2008 -0500
[SCSI] simplify scsi_io_completion()
Which introduced an error whereby ABORTED_COMMAND now gets erroneously
retried in scsi_io_completion. Fix this by returning the behaviour
back to the default no retry.
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit f27bac2761 which converted sd to
use ida instead of idr incorrectly removed sd_index_lock around id
allocation and free. idr/ida do have internal locks but they protect
their free object lists not the allocation itself. The caller is
responsible for that. This missing synchronization led to the same id
being assigned to multiple devices leading to oops.
Reported and tracked down by Stuart Hayes of Dell.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Need to make sure the outgoing pdu can fit into a single skb. When
calulating the max. outgoing pdu payload size, take into consideration
of
- data can be held in the skb's fragment list, assume 512 bytes per
fragment, and
- data can be held in the headroom.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
added per-task struct cxgb3i_task_data to track the data transmiting
progress and the state of the pdus to be transmitted.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- resize the work-request credit array to be based on skb's MAX_SKB_FRAGS.
- split the skb cb into tx and rx portion
- increase the default transmit window to 128K.
- stop queueing up the outgoing pdus if transmit window is full.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Bits 31-8 are marked as reserved and should be ignored while
interpreting a region's code.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The clearing of a vha's req_ques were overrunning during vport
creation. During deletion, vport queues should be torn-down
after all cleanup has occurred.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
To ensure smooth operations amongst the FCoE and NIC side
components of the ISP81xx chip, the FCoE driver (qla2xxx) must
ensure the 10gb NIC driver (qlge) does not timeout waiting for
IDC (Inter-Driver Communication) acknowledgments. The
acknowledgment requirements are trivial -- a simple mirroring of
incoming mailbox registers during the AEN to a process-context
capable mailbox command.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Correct response-queue-0 processing by instructing the firmware
to run with interrupt-handshaking disabled, similarly to what is
now done for all non-0 response queues. Since all
response-queues now run in the same mode, the driver no longer
needs the hot-path 'is-disabled-HCCR' test.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Yanling Qi from LSI found the root cause of the panic, below is his
analysis:
Problem description: the open iscsi driver installs eh_timed_out handler
to the
blank_transport_template of the scsi middle level that causes panic of
timed
out command of other host
Here are the details
Iscsi Session creation
During iscsi session creation time, the iscsi_tcp_session_create() of
iscsi_tpc.c will create a scsi-host for the session. See the statement
marked
with the label A. The statement B replaces the shost->transportt point
with a
local struct variable.
static struct iscsi_cls_session *
iscsi_tcp_session_create(struct iscsi_endpoint *ep, uint16_t cmds_max,
uint16_t qdepth, uint32_t initial_cmdsn,
uint32_t *hostno)
{
struct iscsi_cls_session *cls_session;
struct iscsi_session *session;
struct Scsi_Host *shost;
int cmd_i;
if (ep) {
printk(KERN_ERR "iscsi_tcp: invalid ep %p.\n", ep);
return NULL;
}
A shost = iscsi_host_alloc(&iscsi_sht, 0, qdepth);
if (!shost)
return NULL;
B shost->transportt = iscsi_tcp_scsi_transport;
shost->max_lun = iscsi_max_lun;
Please note the scsi host is allocated by invoking isccsi_host_alloc()
in
libiscsi.c
Polluting the middle level blank_transport_template in
iscsi_host_alloc() of
libiscsi.c
The iscsi_host_alloc() invokes the middle level function
scsi_host_alloc() in
hosts.c for allocating a scsi_host. Then the statement marked with C
assigns
the iscsi_eh_cmd_timed_out handler to the eh_timed_out callback
function.
struct Scsi_Host *iscsi_host_alloc(struct scsi_host_template *sht,
int dd_data_size, uint16_t qdepth)
{
struct Scsi_Host *shost;
struct iscsi_host *ihost;
shost = scsi_host_alloc(sht, sizeof(struct iscsi_host) +
dd_data_size);
if (!shost)
return NULL;
C shost->transportt->eh_timed_out = iscsi_eh_cmd_timed_out;
Please note the shost->transport is the middle level
blank_transport_template
as shown in the code segment below. We see two problems here. 1.
iscsi_eh_cmd_timed_out is installed to the blank_transport_template that
will
cause some body else problem. 2. iscsi_eh_cmd_timed_out will never be
invoked
when iscsi command gets timeout because the statement B resets the
pointer.
Middle level blank_transport_template
In the middle level function scsi_host_alloc() of hosts.c, the middle
level
assigns a blank_transport_template for those hosts not implementing its
transport layer. All HBAs without supporting a specific scsi_transport
will
share the middle level blank_transport_template. Please see the
statement D
struct Scsi_Host *scsi_host_alloc(struct scsi_host_template *sht, int
privsize)
{
struct Scsi_Host *shost;
gfp_t gfp_mask = GFP_KERNEL;
int rval;
if (sht->unchecked_isa_dma && privsize)
gfp_mask |= __GFP_DMA;
shost = kzalloc(sizeof(struct Scsi_Host) + privsize, gfp_mask);
if (!shost)
return NULL;
shost->host_lock = &shost->default_lock;
spin_lock_init(shost->host_lock);
shost->shost_state = SHOST_CREATED;
INIT_LIST_HEAD(&shost->__devices);
INIT_LIST_HEAD(&shost->__targets);
INIT_LIST_HEAD(&shost->eh_cmd_q);
INIT_LIST_HEAD(&shost->starved_list);
init_waitqueue_head(&shost->host_wait);
mutex_init(&shost->scan_mutex);
shost->host_no = scsi_host_next_hn++; /* XXX(hch): still racy */
shost->dma_channel = 0xff;
/* These three are default values which can be overridden */
shost->max_channel = 0;
shost->max_id = 8;
shost->max_lun = 8;
/* Give each shost a default transportt */
D shost->transportt = &blank_transport_template;
Why we see panic at iscsi_eh_cmd_timed_out()
The mpp virtual HBA doesn’t have a specific scsi_transport. Therefore,
the
blank_transport_template will be assigned to the virtual host of the MPP
virtual HBA by SCSI middle level. Please note that the statement C has
assigned
iscsi-transport eh_timedout handler to the blank_transport_template.
When a mpp
virtual command gets timedout, the iscsi_eh_cmd_timed_out() will be
invoked to
handle mpp virtual command timeout from the middle level
scsi_times_out()
function of the scsi_error.c.
enum blk_eh_timer_return scsi_times_out(struct request *req)
{
struct scsi_cmnd *scmd = req->special;
enum blk_eh_timer_return (*eh_timed_out)(struct scsi_cmnd *);
enum blk_eh_timer_return rtn = BLK_EH_NOT_HANDLED;
scsi_log_completion(scmd, TIMEOUT_ERROR);
if (scmd->device->host->transportt->eh_timed_out)
E eh_timed_out =
scmd->device->host->transportt->eh_timed_out;
else if (scmd->device->host->hostt->eh_timed_out)
eh_timed_out = scmd->device->host->hostt->eh_timed_out;
else
eh_timed_out = NULL;
if (eh_timed_out) {
rtn = eh_timed_out(scmd);
It is very easy to understand why we get panic in the
iscsi_eh_cmd_timed_out().
A scsi_cmnd from a no-iscsi device definitely can not resolve out a
session and
session->lock. The panic can be happed anywhere during the differencing.
static enum blk_eh_timer_return iscsi_eh_cmd_timed_out(struct scsi_cmnd
*scmd)
{
struct iscsi_cls_session *cls_session;
struct iscsi_session *session;
struct iscsi_conn *conn;
enum blk_eh_timer_return rc = BLK_EH_NOT_HANDLED;
cls_session = starget_to_session(scsi_target(scmd->device));
session = cls_session->dd_data;
debug_scsi("scsi cmd %p timedout\n", scmd);
spin_lock(&session->lock);
This patch fixes the problem by moving the setting of the
iscsi_eh_cmd_timed_out to iscsi_add_host, which is after the LLDs
have set their transport template to shost->transportt.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
During cancel testing it has been shown that 15 seconds is not
nearly long enough for the VIOS to respond to a cancel under
loaded situations. Increasing this timeout to 60 seconds allows
time for the VIOS to cancel the outstanding commands and prevents
us from escalating to a full host reset, which can take much longer.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ibmvfc driver has a bug in its SCN handling. If it receives
an ELS event such asn an N-Port SCN event or an unsolicited PLOGI,
or any other SCN event which causes ibmvfc_reinit_host to be called,
it is possible that we will call fc_remote_port_add for a target
that already has an rport added, which can result in duplicate
rports getting created for the same targets. Fix this by calling
fc_remote_port_rolechg in this scenario instead to report any possible
role change that may have occurred.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently the ibmvfc driver sets the IBMVFC_CLASS_3_ERR flag
in the VFC Frame if both the adapter and the device claim support
for Class 3. However, this bit actually refers to Class 3 Error
Recovery, which is currently not supported by the VIOS. Setting this
bit can cause lots of command timeout responses from the VIOS resulting
in general instability. Fix this by never setting this bit.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Hi,
we have run into an issue with blktrace being started for sg devices.
Please apply.
Thanks,
Martin
From: Martin Peschke <mpeschke@linux.vnet.ibm.com>
The device number denoting a generic SCSI devices (sg) in a blktrace
trace is broken; major and minor are always 0. It looks like
sdp->device->sdev_gendev.devt is not initialized properly.
The fix below uses other data to make up a valid device number,
similar to the way an sg device number is generated for sysfs output.
Reported-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We were running i/o and performing a bunch of hba resets in a loop.
This forces a lot of target removes and then rescans. Since the
resets are occuring during scan it's causing the scan i/o to timeout,
invoking error recovery, etc. We end up getting some nasty crashing
in scsi_scan.c due to references to old sdevs that are failing
but had some lingering references that kept them around.
Fix by setting device state to SDEV_DEL if the LLD's slave_alloc
fails.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ibmvscsi client driver is not unmapping the SCSI command after
encountering a DMA mapping error while trying to map an indirect
scattergather list for the event pool. This leads to a leak of DMA
entitlement that could result in the device failing future DMA operations
in a CMO environment.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently, netlink_broadcast() reports errors to the caller if no
messages at all were delivered:
1) If, at least, one message has been delivered correctly, returns 0.
2) Otherwise, if no messages at all were delivered due to skb_clone()
failure, return -ENOBUFS.
3) Otherwise, if there are no listeners, return -ESRCH.
With this patch, the caller knows if the delivery of any of the
messages to the listeners have failed:
1) If it fails to deliver any message (for whatever reason), return
-ENOBUFS.
2) Otherwise, if all messages were delivered OK, returns 0.
3) Otherwise, if no listeners, return -ESRCH.
In the current ctnetlink code and in Netfilter in general, we can add
reliable logging and connection tracking event delivery by dropping the
packets whose events were not successfully delivered over Netlink. Of
course, this option would be settable via /proc as this approach reduces
performance (in terms of filtered connections per seconds by a stateful
firewall) but providing reliable logging and event delivery (for
conntrackd) in return.
This patch also changes some clients of netlink_broadcast() that
may report ENOBUFS errors via printk. This error handling is not
of any help. Instead, the userspace daemons that are listening to
those netlink messages should resync themselves with the kernel-side
if they hit ENOBUFS.
BTW, netlink_broadcast() clients include those that call
cn_netlink_send(), nlmsg_multicast() and genlmsg_multicast() since they
internally call netlink_broadcast() and return its error value.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently a DMA mapping leak that can occur in the ibmvfc
driver if we fail to allocate a scatterlist. Fix this by unmapping
the scatterlist in the failure path. Additionally, only log an error
for a scatterlist allocation failure if the log level is greater
than the default, since this can occur when running Active Memory
Sharing and this is not considered an error.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit f78badb1ae ([SCSI] fc
transport: pre-emptively terminate i/o upon dev_loss_tmo timeout)
changed the callback semantics of dev_loss_tmo and
terminate_rport_io such that repeated calls could be made. This
could result in the the driver using stale (NULLed-out, in
dev_loss_tmo) data from the rport. Correct this by addint a
simple check to ensure a valid fcport is attached.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Jeremy Higdon noted
(http://marc.info/?l=linux-scsi&m=123262143131788&w=2) that the
rework done in commit e315cd28b9
was not setting the proper consistent and streaming DMA masks
prior to memory allocations. Correct this and remove the
unnecessary prototype.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When clearing the flash device's SR, the comment is incorrect...
clearing the SR is 2 steps:
1. the SR protect bit is 1, so the first write zero clears only
that bit,
2. the SR protect bit is now 0, so the next write zero clears the
remaining bits.
The sector erase debug print more correctly identifies that the erase failed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit 73208dfd7a (qla2xxx: add
support for multi-queue adapter) inadvertently backed-out the fix
in 5bff55db3d (qla2xxx: Return a
FAILED status when abort mailbox-command fails.).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The flash data was incorrectly being converted (cpu_to_le32())
when using the bulk-flash-write mailbox command (ISP25xx and
above).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Pre-ISP81XX parts (including ISP24xx and ISP25xx) could contain a
firmware image within a segment of flash, driver would fallback
to loading this firmware if the request-firmware interface failed
(userspace .bin file). Moving forward, all ISP81XX parts will
ship with a suggested-to-be-used firmware image within flash
which all driver should first attempt to load. If the flash
firmware load fails, the driver will then fallback to loading
firmware via the request-firmware interface (ql8100_fw.bin).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code would incorrectly bypass serialization if the DPC
thread were performing a big-hammer operation (ISP abort). This
short circuit, though rare, would subsequently stomp on a
secondary thread's mailbox command execution. Found during
ISP81XX testing.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code should work as well given qla24xx_reset_adapter()
is only called in extreme cases where the HBA is taken offline.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Also removes unneeded 'findex' local variable within routine.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
qla4xxx does not check the I_T nexus values correctly
so it ends up creating one session to the target. If
a portal should disappear or they should be reported
in different order the driver will think it is already
logged in when it could now be speaking to a different
target portal or accessing it through a different
initiator port (iscsi initiator port is not tied to
hardware and is just the initiator name plus isid
so you could end up with multiple ports through one
host).
This patch has the driver check the iscsi scsi port
values when matching sessions (we do not check
the initiator name because that is static). It results
in a portal from each target portal group getting
logged into instead of just one per target. In the future
the firmware should hopefully send us notification of other
sessions that are created to other portals within the
same tpgt and the sessions should have different isids.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
I am not sure what happened. It looks like we have always leaked
the q->queue that is allocated from the kfifo_init call. nab finally
noticed that we were leaking and this patch fixes it by adding a
kfree call to iscsi_pool_free. kfifo_free is not used per kfifo_init's
instructions to use kfree.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes cxgb3 invoke the GRO hooks instead of LRO. As
GRO has a compatible external interface to LRO this is a very
straightforward replacement.
I've kept the ioctl controls for per-queue LRO switches. However,
we should not encourage anyone to use these.
Because of that, I've also kept the skb construction code in
cxgb3. Hopefully we can phase out those per-queue switches
and then kill this too.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
serial: Add 16850 uart type support to OF uart driver
hvc_console: Remove tty->low_latency
powerpc: Get the number of SLBs from "slb-size" property
powerpc: is_hugepage_only_range() must account for both 4kB and 64kB slices
powerpc/ps3: printing fixups for l64 to ll64 conversion drivers/video
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/scsi
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/ps3
powerpc/ps3: Printing fixups for l64 to ll64 conversion sound/ppc
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/char
powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/block
powerpc/ps3: Printing fixups for l64 to ll64 conversion arch/powerpc
powerpc/ps3: ps3_repository_read_mm_info() takes u64 * arguments
powerpc/ps3: clear_bit()/set_bit() operate on unsigned longs
powerpc/ps3: The lv1_ routines have u64 parameters
powerpc/ps3: Use dma_addr_t down through the stack
powerpc/ps3: set_dabr() takes an unsigned long
powerpc: Cleanup from l64 to ll64 change drivers/scsi
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_fsl: Return non-zero on error in probe()
drivers/ata/pata_ali.c: s/isa_bridge/ali_isa_bridge/ to fix alpha build
libata: New driver for OCTEON SOC Compact Flash interface (v7).
libata: Add another column to the ata_timing table.
sata_via: Add VT8261 support
pata_atiixp: update port enabledness test handling
[libata] get-identity ioctl: Fix use of invalid memory pointer
for SAS drivers.
Caught by Ke Wei (and team?) at Marvell.
Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the
general trend.
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a powerpc specific driver.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
__scsi_device_lookup_by_target() will always return
the first sdev with a matching LUN, regardless of
the state. However, when this sdev is in SDEV_DEL
scsi_device_lookup_by_target() will ignore this
device and so any valid device on the list after
the deleted device will never be found.
So we have to modify __scsi_device_lookup_by_target()
to skip any device in SDEV_DEL.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
virt_to_page() call should not be used on kernel text and data
addresses. virt_to_page() is used by sg_init_one(). So change padbuf
to be allocated within iscsi_segment.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After restarting ISP the additional queues are not being setup correctly. The
following patch fixes the issue.
Please apply.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Convert arch/powerpc/ over to long long based u64:
-#ifdef __powerpc64__
-# include <asm-generic/int-l64.h>
-#else
-# include <asm-generic/int-ll64.h>
-#endif
+#include <asm-generic/int-ll64.h>
This will avoid reoccuring spurious warnings in core kernel code that
comes when people test on their own hardware. (i.e. x86 in ~98% of the
cases) This is what x86 uses and it generally helps keep 64-bit code
32-bit clean too.
[Adjusted to not impact user mode (from paulus) - sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (45 commits)
[SCSI] qla2xxx: Update version number to 8.03.00-k1.
[SCSI] qla2xxx: Add ISP81XX support.
[SCSI] qla2xxx: Use proper request/response queues with MQ instantiations.
[SCSI] qla2xxx: Correct MQ-chain information retrieval during a firmware dump.
[SCSI] qla2xxx: Collapse EFT/FCE copy procedures during a firmware dump.
[SCSI] qla2xxx: Don't pollute kernel logs with ZIO/RIO status messages.
[SCSI] qla2xxx: Don't fallback to interrupt-polling during re-initialization with MSI-X enabled.
[SCSI] qla2xxx: Remove support for reading/writing HW-event-log.
[SCSI] cxgb3i: add missing include
[SCSI] scsi_lib: fix DID_RESET status problems
[SCSI] fc transport: restore missing dev_loss_tmo callback to LLDD
[SCSI] aha152x_cs: Fix regression that keeps driver from using shared interrupts
[SCSI] sd: Correctly handle 6-byte commands with DIX
[SCSI] sd: DIF: Fix tagging on platforms with signed char
[SCSI] sd: DIF: Show app tag on error
[SCSI] Fix error handling for DIF/DIX
[SCSI] scsi_lib: don't decrement busy counters when inserting commands
[SCSI] libsas: fix test for negative unsigned and typos
[SCSI] a2091, gvp11: kill warn_unused_result warnings
[SCSI] fusion: Move a dereference below a NULL test
...
Fixed up trivial conflict due to moving the async part of sd_probe
around in the async probes vs using dev_set_name() in naming.
iSeries dependent drivers fail to build, when CONFIG_VIOPATH is disabled.
Fix the problem by making those drivers select it.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/arjan/linux-2.6-async:
async: don't do the initcall stuff post boot
bootchart: improve output based on Dave Jones' feedback
async: make the final inode deletion an asynchronous event
fastboot: Make libata initialization even more async
fastboot: make the libata port scan asynchronous
fastboot: make scsi probes asynchronous
async: Asynchronous function calls to speed up kernel boot
Codes to support new FCoE boards.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code would inadvertanly place I/Os on the default
request-queue. Also, correctly pass in the proper MSI-X vector
during response-queue initialization.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code would not read request/response queue pointers.
Also, collapse code into a helper qla25xx_copy_mq() function in
preparation for newer ISP parts.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In preparation for new ISP types with varying dump procedures.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ROMs in recent ISPs have MSI-X support, so it's no longer
necessary for the driver to fallback to interrupt polling during
ISP re-initialization.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Software should not touch this region of flash, as the firmware
will be the only writer and consumer of the region.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
it needs scatterlist.h - indirect chain of includes doesn't work on a
lot of targets.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Andrew Vaszquez said:
> There's a problem that is causing commands returned by the LLD with
> a DID_RESET status to be reissued with cleared cmd->sdb data which
> in our tests are manifesting in firmware detected overruns. Here's
> a snippet of a READ_10 scsi_cmnd upon completion by the storage
The problem is caused by:
commit b60af5b0ad
Author: Alan Stern <stern@rowland.harvard.edu>
Date: Mon Nov 3 15:56:47 2008 -0500
[SCSI] simplify scsi_io_completion()
Because scsi_release_buffers() is called before commands that go
through the ACTION_RETRY and ACTION_DELAYED_RETRY legs are requeued.
However, they're not re-prepared, so nothing ever reallocates the
buffer resources to them. Fix this by releasing the buffers only if
we're not going to go down these legs (but scsi_release_buffers() on
all legs including two in scsi_end_request(); this latter needs a
special version __scsi_release_buffers() because the final one can be
called after the request has been freed, so the bidi test in
scsi_release_buffers(), which touches the request has to be skipped).
Reported-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes part of the scsi probe (which is mostly device spin up and the
partition scan) asynchronous. Only the part that runs after getting the device
number allocated is asynchronous, ensuring that device numbering remains stable.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
When we reworked the transport for the rport lifetimes, in cases where the
rport was reused as a container for tgt id bindings, we inadvertantly
removed the callback to the driver indicating that dev_loss_tmo had fired.
This patch restores that functionality.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix misspelling of "firmware" in qla1280.c
It's spelled "firmware".
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix misspelling of "firmware" in a100u2w.c
It's spelled "firmware".
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix misspelling of "firmware" in megaraid.c
Fixed "firmware", "ownership" and grammar in the same comment.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix misspelling of "firmware" in ql4_mbx.c
It's spelled "firmware".
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
At some point since 2.6.22, the aha152x_cs driver stopped working and
started erring on load with the following messages:
kernel: pcmcia: request for exclusive IRQ could not be fulfilled.
kernel: pcmcia: the driver needs updating to supported shared IRQ lines.
With the following change, the driver works with shared IRQs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [2.6.28], [2.6.27], [2.6.26]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
DIF does not work with 6-byte commands so we previously ignored those
commands when preparing a request. However, DIX does not need
RDPROTECT/WRPROTECT to be set and 6-byte commands are consequently
perfectly valid in host-only mode.
This patch fixes a problem where we would set the wrong DIX operation
when issuing commands to a legacy disk.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Switch tag arrays to u8 to prevent problems on platforms with signed
char.
Reported-by: Tim LaBerge <tim.laberge@Quantum.Com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add application tag to the output displayed on error.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
patch
commit b60af5b0ad
Author: Alan Stern <stern@rowland.harvard.edu>
Date: Mon Nov 3 15:56:47 2008 -0500
[SCSI] simplify scsi_io_completion()
broke DIX error handling. Also, we are now using EILSEQ to indicate
integrity errors to the upper layers (as opposed to regular EIO
failures). This allows filesystems to inspect buffers and decide
whether to retry the I/O. Update scsi_io_completion() accordingly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
A bug was introduced by
commit b60af5b0ad
Author: Alan Stern <stern@rowland.harvard.edu>
Date: Mon Nov 3 15:56:47 2008 -0500
[SCSI] simplify scsi_io_completion()
because the simplification uses scsi_queue_insert(). The problem with
this function is that it expects to be called from the completion path
while the command is still outstanding, so it decrements the device
and host busy counts to do the requeue. The problem is that
scsi_io_completion() is a path executed well after these counts have
*already* been decremented, leading to a double decrement if the
command goes down any error path leading to ACTION_DELAYED_RETRY.
The fix is to allow a private function __scsi_queue_insert() with a
flag to say whether the busy counters should be decremented. This is
made static to scsi_lib.c to discourage other use.
Reported-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
warning: ignoring return value of 'request_irq', declared with attribute
warn_unused_result
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
I increased the delay step by step until loading of mvsas
reliably detected the drive 200 times in sequence. A much better
approach would be to monitor the hardware for some flag which
indicates that port detection has finished, but I do not have any
hardware documentation.
Signed-off-by: Reinhard Nissl <rnissl@gmx.de>
Cc: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Make enlarge_buffer() retry allocation if the previously chosen page
order was too small. Really limit the page order to 6. Return error if
the maximum order is not large enough for the request.
Signed-off-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This integrates st_scsi_kern_execute and st_do_scsi. IOW, it removes
st_scsi_kern_execute. Then st has a single function, st_do_scsi, to
perform SCSI commands.
Signed-off-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
frp_sg_current in struct st_buffer is always zero. We don't need it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
orig_frp_segs in struct st_buffer is always zero. We don't need it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- remove the from_initialization argument, which is always 1. We
always need to use GFP_ATOMIC.
- 'got' valuable is initialized to zero and doesn't change. We don't
need it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This removes the usage of struct scatterlist completely.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This removes struct st_buff_fragment and use reserved_pages array to
store fragment buffer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This removes unused buf_to_sg() that the non-dio path used.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch converts the dio path (mmap) to use st_scsi_execute. IOW,
it removes scsi_execute_async in the non dio path.
scsi_execute_async has gone! This also remove unused st_sleep_done.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch converts the non-dio path (fragment buffer path) to use
st_scsi_execute. IOW, it removes scsi_execute_async in the non-dio
path.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
st_scsi_execute is a helper function to perform SCSI commands
involving data transfer between user and kernel space (st_read and
st_write).
It's the future plan to combine this with st_scsi_kern_execute helper
function.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds struct rq_map_data and the array of pointers to store
fragment buffers to struct st_buffer.
This patch doesn't remove st_buf_fragment but the latter patch does.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch simiplifies the fragment buffer management a bit, all the
buffers in the fragment list become the same size. This is necessary
to use the block layer API (sg driver was modified in the same way)
since the block layer API takes the same size page frames instead of
scatter gatter.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The commit 818827669d (block: make
blk_rq_map_user take a NULL user-space buffer) extended
blk_rq_map_user to accept a NULL user-space buffer with a READ
command. It was necessary to convert sg to use the block layer mapping
API.
This patch extends blk_rq_map_user again for a WRITE command. It is
necessary to convert st and osst drivers to use the block layer
apping API.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This fixes bio_copy_user_iov to properly handle the partial mappings
with struct rq_map_data (which only sg uses for now but st and osst
will shortly). It adds the offset member to struct rq_map_data and
changes blk_rq_map_user to update it so that bio_copy_user_iov can add
an appropriate page frame via bio_add_pc_page().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In a previous patch to fix an issue with error recovery,
the behavior of the max_requests module paramater was also
changed. If, for some reason, max_requests is set to one by
the user, we will end up with a negative number for can_queue.
Fix this by making max_requests not include the two event structs
needed to do error recovery.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The remove() callback in platform drivers should return int in
accordance to the definition of the platform_driver structure.
However, the SGI-specific WD93 SCSI controller driver defines
the callback as a void function, which causes the following
compilation warning:
drivers/scsi/sgiwd93.c:314: warning: initialization from
incompatible pointer type
This patch fixes the warning by changing the return type of
the remove() callback to what the core driver code requires.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If a link down event is received, outstanding commands may get
returned to the ibmvfc driver with a "transaction cancelled implicit"
response. This is currently translated to DID_ABORT, which does
not get retried by SCSI core, but rather passes the failure up
the stack. This can result in I/O errors at the filesystem level.
Fix up this response a well as a few other error responses.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch (as1191) adds a missing "default" case in
scsi_io_completion(), thereby fixing an "uninitialized variable"
error. It also adds a missing newline to a log entry.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Make sure the control flow in scsi_times_out makes sense.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[jejb: limit ioctl to returning 20 characters to avoid overrun
on long device names and add a few more conversions]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As planed, this removes ide-scsi.
The 2.6 kernel supports direct writing to ide CD drives, which
eliminates the need for ide-scsi. ide-scsi has been unmaintained and
marked as deprecated.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James.Bottomley@HansenPartnership.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (33 commits)
ide-cd: remove dead dsc_overlap setting
ide: push local_irq_{save,restore}() to do_identify()
ide: remove superfluous local_irq_{save,restore}() from ide_dump_status()
ide: move legacy ISA/VLB ports handling to ide-legacy.c (v2)
ide: move Power Management support to ide-pm.c
ide: use ATA_DMA_* defines in ide-dma-sff.c
ide: checkpatch.pl fixes for ide-lib.c
ide: remove inline tags from ide-probe.c
ide: remove redundant code from ide_end_drive_cmd()
ide: struct device - replace bus_id with dev_name(), dev_set_name()
ide: rework handling of serialized ports (v2)
cy82c693: remove superfluous ide_cy82c693 chipset type
trm290: add IDE_HFLAG_TRM290 host flag
ide: add ->max_sectors field to struct ide_port_info
rz1000: apply chipset quirks early (v2)
ide: always set nIEN on idle devices
ide: fix ->quirk_list checking in ide_do_request()
gayle: set IDE_HFLAG_SERIALIZE explictly
cmd64x: set IDE_HFLAG_SERIALIZE explictly for CMD646
ali14xx: doesn't use shared IRQs
...
fcoe selects libfc and requires SCSI and PCI (the SCSI requirement is
implicitly covered by an enclosing if). Fix them both up so they
cannot be configured in an invalid state: make LIBFC select
SCSI_FC_ATTRS and make FCOE depend on PCI and select LIBFC.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
cxgb3i requires the cxgb3 net driver, so it selects it. However,
cxgb3 has dependencies which the select cannot see. Fix this by
separating out the cxgb3 dependencies into a separate hidden config
option (CONFIG_CHELSIO_T3_DEPENDS) and make both cxgb3 and cxgb3i
depend on it.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This structure may not be defined if CONFIG_MODULE=n, so never deref
it. Change uses of module->name to module_name(module) and corrects
some dyslexic printks and docbook comments.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The cxgb3i was using skb->sp pointer for some internal book-keeping
which is not related to the secure path. Changed it to use skb->cb[]
instead.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch implements the cxgb3i iscsi connection acceleration for the
open-iscsi initiator.
The cxgb3i driver offers the iscsi PDU based offload:
- digest insertion and verification
- payload direct-placement into host memory buffer.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Now that (almost) all host drivers have been fixed not to abuse ide_lock
and core code usage of ide_lock has been sanitized we may safely replace
ide_lock by per-hwgroup locks.
This patch is partially based on earlier patch from Ravikiran G Thirumalai.
While at it:
- don't use deprecated HWIF() and HWGROUP() macros
- update locking documentation in ide.h
v2:
Add missing spin_lock_init(&hwgroup->lock). (Noticed by Elias Oltmanns)
Cc: Vaibhav V. Nivargi <vaibhav.nivargi@gmail.com>
Cc: Alok N. Kataria <alokk@calsoftinc.com>
Cc: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Cc: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Following changes have been made:
1. Scan outstanding commands only in the queue where it is submitted
2. Update queue registers directly in the fast path
3. Queue specific BAR is remapped only for multiq capable adapters
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This fixes the regression introduced by the commit
58e2a02eb1 (eata: convert to use the
data buffer accessors), reported:
http://marc.info/?t=122987621300006&r=1&w=2
- fix DMA_NONE handling in map_dma()
- this driver can't use scsi_dma_map since host->shost_gendev.parent
is not set properly (it uses scsi_register).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reported-by: Arthur Marsh <arthur.marsh@internode.on.net>
Tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
While doing various error injection testing, such as cable
pulls and target moves, some issues were observed in handling
these events. This patch improves the way these events are handled
by increasing the delay waiting for the fabric to settle and also
changes the behavior of Link Up to break the CRQ to ensure everything
gets cleaned up properly on the VIOS.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Pre-emptively terminate i/o on the rport if dev_loss_tmo has fired.
The desire is to terminate everything, so that the i/o is cleaned up
prior to the sdev's being unblocked, thus any outstanding timeouts/aborts
are avoided.
Also, we do this early enough such that the rport's port_id field is
still valid. FCOE libFC code needs this info to find the i/o's to
terminate.
Signed-off-by: James Smart <james.smart@emulex.com>
[michaelc@cs.wisc.edu: remove extra scsi_target_unblock call]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made.
1. qla_hw_data structure holds an array for request queue pointers,
and an array for response queue pointers.
2. The base request and response queues are created by default.
3. Additional request and response queues are created at the time of vport
creation. If queue resources are exhausted during vport creation, newly
created vports use the default queue.
4. Requests are sent to the request queue that the vport was assigned
in the beginning.
5. Responses are completed on the response queue with which the request queue
is associated with.
[fixup memcpy argument reversal spotted by davej@redhat.com]
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Encapsulation protocol for running Fibre Channel over Ethernet interfaces.
Creates virtual Fibre Channel host adapters using libfc.
This layer is the LLD to the scsi-ml. It allocates the Scsi_Host, utilizes
libfc for Fibre Channel protocol processing and interacts with netdev to
send/receive Ethernet packets.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
libFC is composed of 4 blocks supported by an exchange manager
and a framing library. The upper 4 layers are fc_lport, fc_disc,
fc_rport and fc_fcp. A LLD that uses libfc could choose to
either use libfc's block, or using the transport template
defined in libfc.h, override one or more blocks with its own
implementation.
The EM (Exchange Manager) manages exhcanges/sequences for all
commands- ELS, CT and FCP.
The framing library frames ELS and CT commands.
The fc_lport block manages the library's representation of the
host's FC enabled ports.
The fc_disc block manages discovery of targets as well as
handling changes that occur in the FC fabric (via. RSCN events).
The fc_rport block manages the library's representation of other
entities in the FC fabric. Currently the library uses this block
for targets, its peer when in point-to-point mode and the
directory server, but can be extended for other entities if
needed.
The fc_fcp block interacts with the scsi-ml and handles all
I/O.
Signed-off-by: Robert Love <robert.w.love@intel.com>
[jejb: added include of delay.h to fix ppc64 compile prob spotted by sfr]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ibmvscsi driver currently has a bug in it which can result
in it using up all its event structs for commands. If something
results in all those commands timing out, we won't have any resources
left to send aborts or resets. This results in escalating to a host reset
in order to recover, which is a bit heavy handed. This fixes it
by reducing can_queue by two in order to have resources to do EH.
It also changes the max_requests module parameter so that it is not
writable at runtime, since the code really does not handle it changing
at runtime.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces st_do_scsi in st_int_ioctl with st_scsi_kern_execute.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces st_do_scsi in get_location (READ_POSITION) with
st_scsi_kern_execute.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces st_do_scsi in write_mode_page (MODE_SELECT) with
st_scsi_kern_execute.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces st_do_scsi in read_mode_page (MODE_SENSE) with
st_scsi_kern_execute.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces st_do_scsi in check_tape (READ_BLOCK_LIMITS and
MODE_SENSE) with st_scsi_kern_execute.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces st_do_scsi in st_flush (WRITE FILEMARKS) with
st_scsi_kern_execute.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces st_do_scsi in cross_eof (SPACE) with
st_scsi_kern_execute.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces st_do_scsi in do_load_unload (START STOP) with
st_scsi_kern_execute.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces st_do_scsi in set_location (LOCATE 10) with
st_scsi_kern_execute.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces st_do_scsi in test_ready (TEST_UNIT_READY) with
st_scsi_kern_execute.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
st_scsi_kern_execute is a helper function to perform SCSI commands
synchronously. It supports data transfer with a liner in-kernel buffer
(not scatter gather). st_scsi_kern_execute internally uses
scsi_execute().
The majority of st_do_scsi can be replaced with
st_scsi_kern_execute. This is a preparation for rewriting st_do_scsi
to remove obsolete scsi_execute_async().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This moves st_request initialization code to st_allocate_request()
form st_do_scsi(). This is a preparation for making
st_allocate_request() usable for everyone, not only st_do_scsi().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add SCSI data path, error handling, and debugfs code to complete
BlockGuard support.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update struct definitions, #defines, sysfs entries, and initialization
to support BlockGuard.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Fix mailbox buffer leak on dump mailbox completion
- Fix mbuf leak in lpfc_pci_probe_one() SLI-2 mode error path
- Don't allocate HBQs in interrupt context
- Use correct size for FCP response buffer so that all available sense
data is copied
- Fix jiffies calculation to prevent crash when collecting statistical
data
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Per the recent discussions at the Linux Plumbers Conference, when
enabling MSI or MSI-X, generate a test interrupt to verify the
interrupt routing is working properly. If the test interrupt fails,
fall back to MSI first, and if that fails as well, to INTx. If the
interrupt test fails with INTx, log an error and fail the PCI probe.
Also changed the use of spin_(lock|unlock) to the _irq(save|restore)
variants in the interrupt handlers because with multi-message MSI-X,
both interrupt handlers can now run in parallel.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Avoid polling HBA Error Attention when HBA's PCI channel is offline
due to PCI EEH
- Fix handling of RSCN with non-zero event qualifiers
- Remove unnecessary sleeps during HBA initialization which slow down
driver load
- Fix internal and external loopback on FCoE HBAs
- Fix incorrect decrement of cmd_pending count in lpfc_queuecomand
error path
- Fix reporting of port busy events to management application
- Rename lpfc_adjust_queue_depth() to lpfc_rampdown_queue_depth() for
consistency with its partner lpfc_rampup_queue_depth()
- Delete redundant lpfc_cmd->start_time = jiffies assignment in
lpfc_queuecommand()
- Fix handling for ELS, mailbox and heartbeat time outs in the worker
thread by removing unnecessary checking of the work_port_events
flags.
- Fix NULL pointer dereference in lpfc_prep_els_iocb
- In lpfc_device_recov_npr_node(), move clearing of NLP_NPR_2B_DISC
flag after call to lpfc_cancel_retry_delay_tmo() to keep
targets-in-discovery count correct
- Remove lpfc_probe_one()'s call to scsi_scan_host() which could cause
concurrent SCSI scans to step on each other
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The phba hbq_get address was setup before the HBA reported support for
Interrupt Enable Block (INB). This caused loopback tests to fail
after all HBQs had been used once. Moved setting of hba_get until
after config port mailbox command completes.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Added FC_REG_VPORTRSCN_EVENT to lpfc_nl.h
- Added code to provide option ROM version from HBA and via sysfs
- Added support for HPS bit in config port mailbox command to tell HBA
that host group pointers are in host memory.
- Bugfix for Extended Error Handling (EEH) support on IBM PowerPC P6
platform with MSI enabled
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Fix lock up on rmmod with vports defined by having
lpfc_pci_remove_one() invoke fc_vport_terminate() to remove all the
vports before invoking fc_remove_host() for the physical port
- Fix echotest failure when NPIV is enabled
- Add the vport_disable function to the physical port's transport
template to make the vport disable attribute visible
- Set the vport state to DISABLE on create if the disable flag is
true
- Call lpfc_alloc_sysfs_attr() for vports so that statistical data
collection works on them
- Support setting a vport's symbolic name via sysfs by writing to
/sys/class/fc_vport/vportX/symbolic_name
- Fix create vport fails when link is down or in loop mode. Should be
able to be create vports any time NPIV is enabled
- Fix slow vport deletes when deleting multiple vports at once
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In the IOCB completion handler, always check if the node is valid
before accessing the node object. Added lpfc_initialize_node() to
initialize nodes.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add kernel-doc function headers to lpfc_scsi.c
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Implement lpfc_pci_suspend_one() and lpfc_pci_resume_one() and
register them in the pci_driver table.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rework RSCN netlink event to send entire RSCN payload
Also replaces (SCSI_NL_VID_TYPE_PCI | PCI_VENDOR_ID_EMULEX) with
LPFC_NL_VENDOR_ID
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch changes scsi_probe_lun() to retry INQUIRY if the device has
not actually sent back any INQUIRY data,
This enables the Thecus N2050 storage device to work better. The
firmware on that device starts up strangely; it sends no data in
response to the initial INQUIRY, and it sends the INQUIRY information
in response to the followup REQUEST SENSE. But after that it works
better, so retrying the INQUIRY is enough to get it going.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi_execute() and scsi_execute_req() discard the residual length
information. Some callers need it. This adds residual argument
(optional) to scsi_execute and scsi_execute_req.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In order to ensure the VIOS sees a consistent command buffer, we
need to add a memory barrier after building the command buffer
but before sending the command.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds a delay prior to retrying a failed NPIV login. This fixes
a scenario if the backing fibre channel adapter is getting reset
due to an EEH event, NPIV login will fail. Currently, ibmvfc
retries three times very quickly, resets the CRQ and tries one
more time. If the adapter is getting reset due to EEH, this isn't
enough time. This adds a delay prior to retrying a failed NPIV
login and also increments the number of retries.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
cxgb3i does not offload the processing of the header,
but it will always process the padding. This patch
adds a padding offload flag to detect when the LLD
supports this.
The patch also modifies the header processing so that
we do not try to read/bypass the header dugest in the
skb. cxgb3i will not include it with the header like
with other offload cards.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mgmt setup used to not fail so we did not have to check
the return value. Now with cxgb3i it can so this has us
pass up a error.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We do not need to allocate a itt for data_out, so this
passes the opcode to the alloc_pdu callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bnx2i and cxgb3i need to encode LLD info in the itt so that
the firmware/hardware can process the pdu. This patch allows
the LLDs to encode info in the task->hdr->itt that they
setup in the alloc_pdu callout (any resources that are allocated
can be freed with the pdu in the cleanup_task callout). If
the LLD encodes info in the itt they should implement a
parse_pdu_itt callout. If parse_pdu_itt is not implemented
libiscsi will do the right thing for the LLD.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This hooks iscsi_tcp into the libiscsi_tcp module and removes
code that is now in libiscsi_tcp.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As explained in the previous mails, cxgb3i needs iscsi_tcp's
r2t/data_out and data_in procesing so this just moves functions
that both drivers want to use to a new module libiscsi_tcp. The
next patch will hook iscsi_tcp in.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add iscsi_tcp prefix to most functions. Some are not changed
becuase they are going to move in the next patch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This modifies the login buffer allocation to use __get_free_pages.
It will allow drivers that want to send this data with zero copy
operations to easily line things up on page boundaries.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
libiscsi's iscsi_prep_data_out_pdu now handles what
iscsi_tcp's helpers were so we can remove iscsi_tcp's helpers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This converts iscsi_tcp to the new api and modifies how
it handles r2ts.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
cxgb3i offloads data transfers. It does not offload the entire scsi/iscsi
procssing like qla4xxx and it does not offload the iscsi sequence
processing like how bnx2i does. cxgb3i relies on iscsi_tcp for the
seqeunce handling so this changes how we transfer unsolicitied data by
adding a common r2t struct and helpers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
cxgb3i is unlike qla4xxx and bnx2i in that it does not offload entire
scsi commands or iscsi sequences. Instead it only offloads the transfer
of a ISCSI DATA_IN pdu's data, the digests and padding. This patch fixes up the
iscsi tcp recv path so that it exports its skb recv processing so
cxgb3i and other drivers can call them. All they have to do is pass
the function the skb with the hdr or data pdu header and this function
will do the rest.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since we're trying to eliminate struct scsi_device timeout, the tape
driver has to be updated to use the block queue timeout instead. The
tape use of scsi_device timeout looks to be self consistent, so I don't
think this necessarily fixes any bug, but it has to be done to allow me
to remove the timeout parameter from struct scsi_device.
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
On the Quadra 900 and 950 there are two ESP chips sharing one IRQ. Because
the shared IRQ is edge-triggered, we must make sure that an IRQ transition
from one chip doesn't go unnoticed when the shared IRQ is already active
due to the other. This patch prevents interrupts getting lost so that both
SCSI busses may be used simultaneously.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix asm constraints and arguments so as not to transfer an odd byte when
there may be more words to transfer. The bug would probably also cause
exceptions sometimes by transferring one too many bytes.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The following patch changes the handling of bus reset when issued from a
vport. In the bus reset code, an extra check is made to make sure that the lip
reset is not done before resetting the targets if the bus reset came from a
vport.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch (as1142b) consolidates a lot of repetitious code in
scsi_io_completion(). It also fixes a few comments. Most
importantly, however, it clearly distinguishes among the three sorts
of retries that can be done when a command fails to complete:
Unprepare the request and resubmit it, so that a new
command will be created for it.
Requeue the request directly so that it will be retried
immediately using the same command.
Requeue the request so that it will be retried following
a short delay.
Complete the remainder of the request with an I/O error.
[jejb: Updates
1. For several error conditions, we would now print the sense twice
in slightly different ways, so unify the location of sense
printing.
2. I added more descriptions to actual failure conditions for
better debugging
3. according to spec, ABORTED_COMMAND is supposed to be retried
(except on DIF failure). Our old behaviour of erroring it looks
to be a bug.
4. I'd prefer not to default initialise the action variable because
that ensures that every leg of the error handler has an
associated action and the compiler will warn if someone later
accidentally misses one or removes one.
]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The virtual fibre channel stack can return a failure response for a command
indicating the port login has been invalidated without sending the client
an async event. Add code to handle this response and initiate a PLOGI.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The CRQs used by the ibmvfc driver are read and written by both
the client and the server. Therefore, we need to mark them volatile
so that we do not cache their contents when handling an interrupt.
This fixes a problem which can surface as occasional command timeouts.
No commands were actually timing out, but due to accessing cached data
for the CRQ in the interrupt handler, the interrupt was not processing
all command completions as it should.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fixes an oops that can occur in the interrupt handler
if we get a lot of async events.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
drivers/scsi/qla2xxx/qla_os.c: In function 'qla2x00_probe_one':
drivers/scsi/qla2xxx/qla_os.c:1582: warning: 'mem_only' is used uninitialized in this function
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made:
1. Outstanding commands are based on a request queue, scsi_qla_host
does not maintain it anymore.
2. start_scsi is accessed via isp_ops struct instead of direct
invocation.
3. Interrupt registrations are done using response queue instead of
device id.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made to the qla2xxx FC driver in
preparation for the multi- queue and future SR IOV hardware.
1. scsi_qla_host structure has been changed to contain scsi host
specific data only.
2. A new structure, qla_hw_data is created to contain HBA specific
hardware data.
3. Request and response IO specific data strucures are created.
4. The global list of fcports for the hba is not maintained anymore,
instead a fcport list is construted on per scsi_qla_host.
Signed-of-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch improves handling of TASK ABORTED status by Linux SCSI
mid-layer. Currently, command returned with this status considered
failed and returned to upper layers. It leads to additional error
recovery load on file systems and block layer, which sometimes can
cause undesired side effects, like I/O errors and file systems
corruptions. See http://lkml.org/lkml/2008/11/1/38, for instance.
From other side, TASK ABORTED status is returned by SCSI target if the
corresponding command was aborted by another initiator and the target
has TAS bit set in the control mode page. So, in the majority of cases
commands with TASK ABORTED status should be simply retried. In other
cases, maybe_retry path will not retry if no retries are allowed.
This patch implement suggestion by James Bottomley from
http://marc.info/?l=linux-scsi&m=121932916906009&w=2.
Signed-off-by: Vladislav Bolkhovitin <vst@vlnb.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When the mode select sent to the controller fails with the retryable
error, it is better to retry the mode_select from the hardware handler
itself, instead of propagating the failure to dm-multipath.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When the controller ownership is changed (from passive to active),
check_ownership() doesn't set the state of the device to ACTIVE.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Reported-by: "Moger, Babu" <Babu.Moger@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
...and the list of recent breakage goes on and on, this time
it's 242f9dcb8b (block: unify request timeout handling)
which broke it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When unsigned, scsi_dma_map may return -ENOMEM without triggering BUG_ON()
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use the macro DIV_ROUND_UP and eliminate the variable rounded_up, as
suggested by Matthew Wilcox.
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: David Miller <davem@davemloft.net>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Stops gcc from complaining about a possible uninitialized
variable being used in ibmvfc_reset_device.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If the ibmvfc driver is in discovery attempting to log into a target
and it encounters an error, the command may get retried one or more
times, depending on the error received. If the retries are
unsuccessful such that the discovery thread gives up on discovery to
that target, the target ends up in a state where, if SCSI core had
previously known about the device, the host will get unblocked but the
host will not be logged into the target, causing any commands sent to
the target to fail. This patch fixes this so that if this occurs, the
target is deleted such that the normal dev_loss processing can occur
instead.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Due to an ambiguity in the VIOS VFC interface specification,
abort/cancel handling is not done correctly and can result in double
completion of commands. In order to cancel all outstanding commands to
a device, a cancel must be sent, followed by an abort task set. After
the responses are received for these commands, there may still be
commands outstanding, in the process of getting flushed back, in which
case, we need to wait for them. This patch removes the assumption that
if the abort and the cancel both complete successfully that the device
queue has been flushed and waits for all the responses to come back.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If either a "transport fault" or a "general transport" error is received
and no other error information is available, the command is improperly
returned as successful. Fix this to return DID_ERROR in this case.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ibmvfc log level filtering logic was reversed. The log_level scsi
host parameter should result in more verbose logs when log_level is
larger, not smaller.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We need to check the address that pci_alloc_consistent() returns since
it might fail.
When pci_alloc_consistent() fails, some IOMMUs set the dma_handle
argument to zero. So we can't use fibptr->hw_fib_pa directly here.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Aacraid List <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use the newly introduced pci_ioremap_bar() function in drivers/scsi.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Brian King <brking@us.ibm.com>
Cc: Ed Lin <ed.lin@promise.com>
Cc: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix kernel-doc parameter warning and correct the function name:
Warning(linux-next-20081022//drivers/scsi/scsi_ioctl.c:281): No description found for parameter 'ndelay'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: use the new byteorder headers
fbcon: Protect free_irq() by MACH_IS_ATARI check
fbcon: remove broken mac vbl handler
m68k: fix trigraph ignored warning in setox.S
macfb annotations and compiler warning fix
m68k: mac baboon interrupt enable/disable
m68k: machw.h cleanup
m68k: Mac via cleanup and commentry
m68k: Reinstate mac rtc
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
Remove some more cruft from machw.h and drop the #include where it isn't
needed.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] mpt fusion: clear list of outstanding commands on host reset
[SCSI] scsi_lib: only call scsi_unprep_request() under queue lock
[SCSI] ibmvstgt: move crq_queue_create to the end of initialization
[SCSI] libiscsi REGRESSION: fix passthrough support with older iscsi tools
[SCSI] aacraid: disable Dell Percraid quirk on Adaptec 2200S and 2120S
It's called under that lock everywhere else and it does alter the
request state, so it should be.
This one occurance in scsi_requeue_command() could open a window where
req->special is set to NULL while the requests is going through either
timeout or completion processing leading to NULL pointer derefs of the
sort complained of in bugzillas 12020 and 12195.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The test-unit-ready portion of this patch was causing boots to fail on
my test machine (as in http://lkml.org/lkml/2008/12/5/161). With this
patch in place, the system is booting reliably.
Mike Anderson found the same problem in the hp_hw_start_stop code,
and I applied the same solution in cdrom_read_cdda_bpc.
Signed-off-by: Alan D. Brunelle <alan.brunelle@hp.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The hardware supports transfers up to a page boundary per buffer.
Currently, we work around that in the DMA code by splitting each
buffer up as we run through the scatterlist. Avoid this by telling
the block layers about the hardware restriction.
Eventually, this will allow us to phase out the splitting code,
but not until the old IDE layer allows us to control the value it
gives to blk_queue_segment_boundary().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Calling crq_queue_create could lead to the creation of a rport. We
need to set up everything before creating a rport. This moves
crq_queue_create to the end of initialization to avoid a race which
causes an oops if lost.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reported-by: Olaf Hering <olh@suse.de>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update FMODE_NDELAY before each ioctl call so that we can kill the
magic FMODE_NDELAY_NOW. It would be even better to do this directly
in setfl(), but for that we'd need to have FMODE_NDELAY for all files,
not just block special files.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This regression was added in 2.6.27, when the mtask and ctask were
merged into the the common task struct. The patch applies to
scsi-rc-fixes, but also applies to 2.6.27 with some offsets.
The problem is that __iscsi_conn_send_pdu assumes that userspace was
not sending nops with the format it is checking for in the "if" below.
It turns out that older userspace tools are. This patch moves the
setting of the internal ping_task tracker (it tracks libiscsi current
outstanding nop) to iscsi_send_nopout which is only used by kernel callers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
A lot of 64bit machines with Adaptec 2200S and 2120S controllers don't
recognize SCSI disks any more with the patch
commit 94cf6ba11b
Author: Salyzyn, Mark <mark_salyzyn@adaptec.com>
Date: Thu Dec 13 16:14:18 2007 -0800
[SCSI] aacraid: fix driver failure with Dell PowerEdge Expandable RAID Controller 3/Di
but fail with tons of "aac_srb: aac_fib_send failed with status: 8195"
instead. This patch disables the quirk introduced in the change cited
above for those two controllers again.
[thenzl: added 2120S Controller]
Signed-off-by: Gernot Hillier <gernot.hillier@siemens.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Cc: AACRAID list <aacraid@adaptec.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] stex: switch to block timeout
[SCSI] make scsi_eh_try_stu use block timeout
[SCSI] megaraid_sas: switch to block timeout
[SCSI] ibmvscsi: switch to block timeout
[SCSI] aacraid: switch to block timeout
[SCSI] zfcp: prevent double decrement on host_busy while being busy
[SCSI] zfcp: fix deadlock between wq triggered port scan and ERP
[SCSI] zfcp: eliminate race between validation and locking
[SCSI] zfcp: verify for correct rport state before scanning for SCSI devs
[SCSI] zfcp: returning an ERR_PTR where a NULL value is expected
[SCSI] zfcp: Fix opening of wka ports
[SCSI] zfcp: fix remote port status check
[SCSI] fc_transport: fix old bug on bitflag definitions
[SCSI] Fix hang in starved list processing
stex sets the timeout in its slave configure routine for all devices.
This now needs to update the request queue timeout in block.
Cc: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi_eh_try_stu() was still using the timeout parameter in the device
which is now not set (i.e. zero filled) meaning that it waited no time
at all for the start unit command to complete (leading the routine to
conclude failure every time). This lead to a 2.6.27 regression:
http://bugzilla.kernel.org/show_bug.cgi?id=12120
Where firewire devices that were non spec compliant wouldn't spin up.
Fix this by using the block queue timeout value instead.
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
megaraid_sas sets the timeout in its slave configure routine for devices
on special channels. This now needs to update the request queue timeout
in block.
Cc: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ibmvscsi sets the timeout in its slave configure routine for disk
devices. This now needs to update the request queue timeout in block.
Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
aacraid updates the timeout in its slave configure routine if it is too
small. This now needs to update the request queue timeout in block.
Cc: AACRAID list <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
PCI side of driver should be devinit, not init
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code
if (shost->dma_channel != NO_ISA_DMA)
free_dma(shost->dma_channel);
in there is triggerable only if we have CONFIG_ISA (we only set ->dma_channel to
something other than NO_ISA_DMA under #ifdef CONFIG_ISA). OTOH, free_dma() is
not guaranteed to be there in absense of CONFIG_ISA. IOW, driver runs into
undefined symbols on PCI-but-not-ISA configs (e.g. on frv) and it's a false
positive.
Fix: put the entire if () under #ifdef CONFIG_ISA; behaviour doesn't change and
dependency on free_dma() disappears for !CONFIG_ISA.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Close possible infinite loop with interrupts off when devices are
added back to the starved list.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=11898
Reported-by: <alex.shi@intel.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
dpt_i2o.c::adpt_i2o_to_scsi() reads the value at (reply+5) which
should contain the length in bytes of the transferred data. This
would be correct if reply was a u32 *. However it is a void * here,
so we need to read the value at (reply+20) instead.
The value at (reply+5) is usually 0xff0000, which is apparently
'large enough' and didn't cause any trouble until 2.6.27 where
commit 427e59f09f
Author: James Bottomley <James.Bottomley@HansenPartnership.com>
Date: Sat Mar 8 18:24:17 2008 -0600
[SCSI] make use of the residue value
caused this to become visible through e.g. iostat -x .
Signed-off-by: Miquel van Smoorenburg <mikevs@xs4all.net>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Drivers want to be able to return DID_TRANSPORT_DISRUPTED and
have it do the right thing for commands like tape and passthrouh
as far as retries go. The LLDs previously used DID_BUS_BUSY or DID_ERROR
which followed the cmd->retries limit, but DID_TRANSPORT_DISRUPTED
was skipping that check so it could have caused a problem with tape
commands.
This patch has DID_TRANSPORT_DISRUPTED check the cmd->retries/cmd->allowed.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Reed noted
(https://bugzilla.novell.com/show_bug.cgi?id=421330) that the
driver was incorrectly returning a SUCCESS status if the driver's
request to the firmware to abort a command failed. By doing so,
the mid-layer believed, incorrectly, that the command has
completed and has been returned (ultimately clearing
scsi_cmnd.request_buffer) yet the driver still has the command.
What should correctly happen is a mid-layer escalation
(device-reset, etc.) of recovery during which the driver will
eventually return the outstanding commands to the mid-layer.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For 23XX ISPs, max_vports may return an invalid value.
Do not honour it.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use correct block size (4K) for erase command 0x20 for Atmel
Flash. Use dword addresses for determining sector boundary.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi_cmnd->cmnd was changed from a static array to a pointer post
2.6.25. It breaks mega_internal_command():
static int
mega_internal_command(adapter_t *adapter, megacmd_t *mc, mega_passthru *pthru)
{
...
scb = &adapter->int_scb;
memset(scb, 0, sizeof(scb_t));
scmd = &adapter->int_scmd;
memset(scmd, 0, sizeof(Scsi_Cmnd));
sdev = kzalloc(sizeof(struct scsi_device), GFP_KERNEL);
scmd->device = sdev;
scmd->device->host = adapter->host;
scmd->host_scribble = (void *)scb;
scmd->cmnd[0] = MEGA_INTERNAL_CMD;
mega_internal_command() uses scsi_cmnd allocated internally so
scmd->cmnd is NULL here. This patch adds a static array for cdb to
adapter_t and uses it here. This also uses
scsi_allocate_command/scsi_free_command, the recommended way to
allocate struct scsi_cmnd since the driver might use sense_buffer in
struct scsi_cmnd.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: Boaz Harrosh <bharrosh@panasas.com>
Tested-by: Pascal Terjan <pterjan@gmail.com>
Reported-by: Pascal Terjan <pterjan@gmail.com>
Acked-by: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
fdomain_cs: Sort out modules with duplicate description
pcmcia: Whine harder about use of EXCLUSIVE
pcmcia: IRQ_TYPE_EXCLUSIVE is long obsoleted
The iscsi_ibft.c changes are almost certainly a bugfix as the
pointer 'ip' is a u8 *, so they never print the last 8 bytes
of the IPv6 address, and the eight bytes they do print have
a zero byte with them in each 16-bit word.
Other than that, this should cause no difference in functionality.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Love
Steve Ma
Vasu Dev
Chris Leech
Abhijeet Joglekar
Matthew Wilcox
David S. Miller
James Bottomley
Tejun Heo
Karen Xie
HighPoint Linux Team
Russell King
Andrew Vasquez
Anirban Chakraborty
Julia Lawall
Mike Christie
Shyam_Iyer@Dell.com
Brian King
Martin Peschke
James Smart
Robert Jennings
Pablo Neira Ayuso
Seokmann Ju
Joe Carnuccio
Lalit Chandivade
Herbert Xu
Linus Torvalds
Jeff Garzik
Stephen Rothwell
Hannes Reinecke
ILLES, Marton
Ingo Molnar
Kamalesh Babulal
Al Viro
Arjan van de Ven
Nick Andrew
Frederik Schwarzer
Larry Finger
Martin K. Petersen
Roel Kluin
Geert Uytterhoeven
Reinhard Nissl
Kai Makisara
FUJITA Tomonori
Dmitri Vorobiev
Alan Stern
Christoph Hellwig
Kay Sievers
Bartlomiej Zolnierkiewicz
Mark Nelson
Finn Thain
Babu Moger
Vladislav Bolkhovitin
Chandra Seetharaman
Ilpo Järvinen
Alan Cox
Randy Dunlap
Alan D. Brunelle
Hillier, Gernot
Al Viro
Miquel van Smoorenburg
Mike Christie
Michael Reed
Shyam Sundar
Harvey Harrison