Eliminate some of the registers in ethtool register test to reduce
driver size.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support WoL during shutdown by calling
tg3_set_power_state(tp, PCI_D3hot) during tg3_close().
Change the power state parameter to pci_power_t type and use
constants defined in pci.h.
Certain ethtool operations cannot be performed after tg3_close()
because the device will go to low power state. Add return -EAGAIN
in such cases where appropriate.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable TSO by default on newer chips that support TSO in hardware.
Leave TSO off by default on older chips that do firmware TSO because
performance is slightly lower.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (230 commits)
[SPARC64]: Update defconfig.
[SPARC64]: Fix 2 bugs in huge page support.
[SPARC64]: CONFIG_BLK_DEV_RAM fix
[SPARC64]: Optimized TSB table initialization.
[SPARC64]: Allow CONFIG_MEMORY_HOTPLUG to build.
[SPARC64]: Use SLAB caches for TSB tables.
[SPARC64]: Don't kill the page allocator when growing a TSB.
[SPARC64]: Randomize mm->mmap_base when PF_RANDOMIZE is set.
[SPARC64]: Increase top of 32-bit process stack.
[SPARC64]: Top-down address space allocation for 32-bit tasks.
[SPARC64] bbc_i2c: Fix cpu check and add missing module license.
[SPARC64]: Fix and re-enable dynamic TSB sizing.
[SUNSU]: Fix missing spinlock initialization.
[TG3]: Do not try to access NIC_SRAM_DATA_SIG on Sun parts.
[SPARC64]: First cut at VIS simulator for Niagara.
[SPARC64]: Fix system type in /proc/cpuinfo and remove bogus OBP check.
[SPARC64]: Add SMT scheduling support for Niagara.
[SPARC64]: Fix 32-bit truncation which broke sparsemem.
[SPARC64]: Move over to sparsemem.
[SPARC64]: Fix new context version SMP handling.
...
Sun does't put an SEEPROM behind the tigon3 chip, among other things,
so accesses to these areas just give bus timeouts.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 40-bit DMA workaround recently implemented for 5714, 5715, and
5780 needs to be expanded because there may be other tg3 devices
behind the EPB Express to PCIX bridge in the 5780 class device.
For example, some 4-port card or mother board designs have 5704 behind
the 5714.
All devices behind the EPB require the 40-bit DMA workaround.
Thanks to Chris Elmquist again for reporting the problem and testing
the patch.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
semaphore to mutexes conversion.
the conversion was generated via scripts, and the result was validated
automatically via a script as well.
build-tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix gcc warning: ipw2100.c:2460: ISO C90 forbids mixed declarations and code
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: Andrea Merello <andreamrl at tiscali it>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a big array overun found by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies the driver to support the ipw2200-fw-3.0 image format.
The 3.0 fw image does not add any new capabilities, but as a result of
image format changes, it should fix two problems experienced by users:
1) Race conditions with the request_firmware interface and udev/hotplug
are improved as only a single request_firmware call is now required to
load the firmware and microcode (vs. 3 separate calls previously)
2) The monitor mode firmware (sniffer) is now packaged with the correct
boot image so it can now function without frequent restarts.
Note: Once you apply this patch, you will also need to upgrade your
firmware image to the 3.0 version available from:
http://ipw2200.sf.net/firmware.php
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch allows the user to set the handover threshold, i.e. the number
of consecutively missed beacons that will trigger a roaming attempt. The
disassociation threshold is set to 3 times the handover threshold.
Signed-off-by: Olivier Hochreutiner <olivier.hochreutiner@epfl.ch>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This forces one antenna or the other, if the background noise is
significantly quieter in one than the other. It favors the quieter
antenna, and won't kick in unless the difference is significant.
Signed-off-by: Cahill, Ben M <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set a meaningful silence threshold value (replacing our previous "0"
default), which gets rid of the gratuitous "Link deterioration"
notifications that we've been receiving from firmware. This
notification feature tells the driver information to help it determine
when to pre-emptively restart the firmware/ucode in anticipation of
firmware errors! But since setting this new threshold, I haven't seen
any such notifications. At least it keeps the logs a little less busy.
Signed-off-by: Cahill, Ben M <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently iwlist ethX freq[uency]/channel lists all the channels the card
supported for the current region, which includes some channels can only
be used in infrastructure mode. This patch filters these channels out if
the card is currently in ad-hoc mode.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When loading the ipw2200 module with disabled=1, rf_kill is activated after
every mode change. This is caused by ipw_sw_reset() is called when a mode
is changed. The patch fixed the problem by distinguishing the purposes with
the 'option' paramenter.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wpa_supplicant needs to set wpa_enabled unconditionally, with this check
it hasn't been possible to connect to non-WPA networks using wpa_supplicant.
So remove below check.
if (priv->ieee->wpa_enabled &&
network->wpa_ie_len == 0 && network->rsn_ie_len == 0)
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch does two things. It uses the parameter IW_QUAL_DBM which is new
in WE-19 to cause signal level and noise to be reported in dBm by the
wireless tools. It also defines the signal level as an unsigned integer
so that the signal level will be reported by iwlist iface scan.
Signed-off-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace ipw2200 specific frame_hdr_len() with generic
ieee80211 routine ieee80211_get_hdrlen()
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch roll back the change we made to support for the ability to
start/stop independent Tx queues within a single net device in order to
support 802.11e QoS. We need to be able to indicate to the upper layers
that packets of a given priority can not be sent any more without halting
transmission of all packets, and without rescheduling high priority packets
down to the next priority level.
So we return NETDEV_TX_BUSY in this case and rely on the stack would
take care of rescheduling... which it apparently does immediately and
consumes the CPU. This caused the ksoftirqd kernel thread consuming almost
all the CPU...
To put the code back to the way it was before we made these changes we
put the call netif_queue_stop back in ipw_tx_skb. This effectively
disables multiple priority based transmit queues for 802.11e, but given
that its broken anyway...
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Given the amount of support requests for the meaning of the geography code
I've written a patch for printing this information on module load no matter
the debug level.
I've also added a section to the README.ipw2200 file listing the geography
codes and their meaning.
Signed-off-by: Henrik Brix Andersen <brix@gentoo.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the needlessly global function ipw_qos_current_mode()
static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As stated in a comment, the ipw2200 driver uses several routines that
were borrowed from ieee80211_geo.c. As ipw2200 requires ieee80211,
these routines are duplicated. The attached patch, which is sent
as an attachment to preserve whitespace, converts ipw2200.c to use
the ieee80211 versions, thereby reducing bloat in both the source
and binary.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adrian Bunk wrote:
> The Coverity checker spotted the following two array overflows in
> drivers/net/chelsio/sge.c (in both cases, the arrays contain 3
> elements):
[snip]
This is a bug. The array should contain 2 elements. Here is the fix.
Signed-off-by: Scott Bardone <sbardone@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
return -E_NO_BIG_ENDIAN_TESTING;
[E1000]: Fix 4 missed endianness conversions on RX descriptor fields.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Olaf Hering reported a problem on pseries with e100 where ethtool -t would
cause a bus error, and the e100 driver would stop working. Due to the new
load ucode command the cb list must be allocated before calling
e100_init_hw, so remove the call and just let e100_up take care of it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
This patch moves prototypes of global variables and functions to a header
file.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: John Ronciak <john.ronciak@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Coverity checker spotted this dead code (note that (clock_ctrl == 7)
is already handled above).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're leaking an skb in a failure path in this function.
Coverity #632
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Coverity checker spotted these two unused variables.
Please check whether this patch is correct or whether they should be
used.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
o Make sgiseeq_dump_rings static.
o Delete unused sgiseeq_my_reset.
o Move DEBUG define to beginning where it's easier to spot and will be
seen by <linux/kernel.h> as well.
o Use NULL for pointer initialization.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert 3c509 driver to use proper suspend/resume API instead of the
deprecated pm_register/pm_unregister.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains the following possible updates:
- let FORCEDETH no longer depend on EXPERIMENTAL
- remove the "Reverse Engineered" from the option text:
for the user it's important which hardware the driver supports, not
how it was developed
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Michael Chan
Linus Torvalds
Jeff Garzik
David S. Miller
Zhu Yi
Ingo Molnar
Stefan Rompf
Adrian Bunk
James Ketrenos
Olivier Hochreutiner
Cahill, Ben M
Bill Moss
Henrik Brix Andersen
Larry Finger
Scott Bardone
David S. Miller
John W. Linville
Jesse Brandeburg
Dave Jones
Ralf Baechle
Pekka Enberg
Andrew Morton