Fix bug in nvram write function. If the starting nvram address offset
happens to be the last dword of the page, the NVRAM_CMD_LAST bit will
not get set in the existing code. This patch fixes the bug by changing
the "else if" to "if" so that the last dword condition always gets
checked.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a reset_phy parameter to tg3_reset_hw() and tg3_init_hw(). With
the full chip reset during MAC address change, the automatic PHY reset
during chip reset will cause a link down and bonding will not work
properly as a result. With this reset_phy parameter, we can do a chip
reset without link down when changing MAC address or MTU.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the full chip reset when changing MAC address if ASF is enabled.
ASF sometimes uses a different MAC address than the driver. Without
the reset, the ASF MAC address may be overwritten when the driver's
MAC address is changed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some PHY workaround code to reduce jitter on some PHYs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_carrier_off() call during tg3_phy_reset(). This is needed
to properly track the netif_carrier state in cases where we do a
PHY reset with interrupts disabled. The SerDes code will not run
properly if the netif_carrier state is wrong.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Speed up SRAM read and write functions if possible by using MMIO
instead of config. cycles. With this change, the post reset signature
done at the end of D3 power change must now be moved before the D3
power change.
IBM reported a problem on powerpc blades during ethtool self test that
was caused by the memory test taking excessively long. Config. cycles
are very slow on powerpc and the memory test can take more than 10
seconds to complete using config. cycles.
David Miller informed me that an earlier version of the patch caused
problems on sparc64 systems with built-in tg3 chips. This version
fixes the problem by excluding all SUN built-in tg3 chips from doing
MMIO SRAM access.
TG3_FLAG_EEPROM_WRITE_PROT is also set unconditionally when
TG3_FLG2_SUN_570X is set. This should be sane as all SUN chips are
built-in and do not require Vaux switching.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill the TG3_FLAG_NO_{TX|RX}_PSEUDO_CSUM flags because they are not
very useful. This will free up some bits for new flags.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a memory leak (buf wasn't freed) spotted by the
Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (48 commits)
Documentation: fix minor kernel-doc warnings
BUG_ON() Conversion in drivers/net/
BUG_ON() Conversion in drivers/s390/net/lcs.c
BUG_ON() Conversion in mm/slab.c
BUG_ON() Conversion in mm/highmem.c
BUG_ON() Conversion in kernel/signal.c
BUG_ON() Conversion in kernel/signal.c
BUG_ON() Conversion in kernel/ptrace.c
BUG_ON() Conversion in ipc/shm.c
BUG_ON() Conversion in fs/freevxfs/
BUG_ON() Conversion in fs/udf/
BUG_ON() Conversion in fs/sysv/
BUG_ON() Conversion in fs/inode.c
BUG_ON() Conversion in fs/fcntl.c
BUG_ON() Conversion in fs/dquot.c
BUG_ON() Conversion in md/raid10.c
BUG_ON() Conversion in md/raid6main.c
BUG_ON() Conversion in md/raid5.c
Fix minor documentation typo
BFP->BPF in Documentation/networking/tuntap.txt
...
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Undo commit 100c467330
MMIOs timeout more quickly that PCI config cycles and some
of these SRAM accesses can take a very long time, triggering
the MMIO limits on some sparc64 PCI controllers and thus
resulting in bus timeouts and bus errors.
Signed-off-by: David S. Miller <davem@davemloft.net>
Skip the main timer code if interrupts are disabled in the full lock
state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Speed up SRAM read and write functions if possible by using MMIO
instead of config. cycles. With this change, the post reset signature
done at the end of D3 power change must now be moved before the D3
power change.
IBM reported a problem on powerpc blades during ethtool self test
that was caused by the memory test taking excessively long. Config.
cycles are very slow on powerpc and the memory test can take more
than 10 seconds to complete using config. cycles. As a result, NETDEV
WATCHDOG can be triggered during self test and the chip can end up in
a funny state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to check the TG3_FLAG_40BIT_DMA_BUG flag in the workaround code
path instead of device flags.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some older bootcode in some devices may report 0 MAC address in
SRAM when booting up from low power state. This patch fixes the
problem by checking for a valid MAC address in SRAM and falling back
to NVRAM if necessary.
Thanks to walt <wa1ter@myrealbox.com> for reporting the problem
and helping to debug it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for new chip 5755 which is very similar to 5787.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs should not be powered down in tg3_set_power_state() because
of bugs or other hardware limitations.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5700 and 5701 will not return correct SRAM data when the chip is in
D3hot power state. tg3_get_eeprom_hw_cfg() must first put the device
in D0 before reading SRAM.
Thanks to Thomas Chenault at Dell for noticing this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the needlessly global function tg3_request_irq()
static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the netif_carrier_off() call from tg3_init_one()->
tg3_init_link_config() to tg3_open() as is the convention for most other
network drivers.
I was getting a panic after a tg3 device failed to initialize due to DMA
failure. The oops pointed to the link watch queue with spinlock debugging
enabled. Without spinlock debugging, the Oops didn't occur.
I suspect that the link event was getting queued but not executed until
after the DMA test had failed and the device was freed. The link event was
then operating on freed memory, which could contain anything. With this
patch applied, the Oops no longer occurs.
[ Based upon feedback from Michael Chan, we move netif_carrier_off()
to the end of tg3_init_one() instead of moving it to tg3_open() -DaveM ]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some nvram related cleanup:
1. Add a tg3_nvram_read_swab() since swabing the data is frequently
done.
2. Add a function to convert nvram address to physical address
instead of doing it in 2 separate places.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool memory test on 5787 requires a new memory table.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support one-shot MSI on 5787.
This one-shot MSI idea is credited to David Miller. In this mode, MSI
disables itself automatically after it is generated, saving the driver
a register access to disable it for NAPI.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support ipv6 tx csum on 5787 by setting NETIF_F_HW_CSUM.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support 5787 hardware TSO using a new flag TG3_FLG2_HW_TSO_2.
Since the TSO interface is slightly different and these chips have
finally fixed the 4GB DMA problem and do not have the 40-bit DMA
problem, a new hard_start_xmit is used for these chips. All previous
chips will use the old hard_start_xmit that is now renamed
tg3_start_xmit_dma_bug().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support additional nvrams and new nvram format for 5787 and 5754.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix-up tg3_get_ringparam() to return the correct parameters.
Set the jumbo rx ring parameter only if it is supported by the chip
and currently in use.
Add missing value for tx_max_pending, noticed by Rick Jones.
Update version to 3.51.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing netif_running() checks in tg3's dev->set_multicast_list()
and dev->set_mac_address(). If not netif_running(), these 2 calls can
simply return 0 after storing the new settings if required.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support WoL during shutdown by calling
tg3_set_power_state(tp, PCI_D3hot) during tg3_close().
Change the power state parameter to pci_power_t type and use
constants defined in pci.h.
Certain ethtool operations cannot be performed after tg3_close()
because the device will go to low power state. Add return -EAGAIN
in such cases where appropriate.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable TSO by default on newer chips that support TSO in hardware.
Leave TSO off by default on older chips that do firmware TSO because
performance is slightly lower.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (230 commits)
[SPARC64]: Update defconfig.
[SPARC64]: Fix 2 bugs in huge page support.
[SPARC64]: CONFIG_BLK_DEV_RAM fix
[SPARC64]: Optimized TSB table initialization.
[SPARC64]: Allow CONFIG_MEMORY_HOTPLUG to build.
[SPARC64]: Use SLAB caches for TSB tables.
[SPARC64]: Don't kill the page allocator when growing a TSB.
[SPARC64]: Randomize mm->mmap_base when PF_RANDOMIZE is set.
[SPARC64]: Increase top of 32-bit process stack.
[SPARC64]: Top-down address space allocation for 32-bit tasks.
[SPARC64] bbc_i2c: Fix cpu check and add missing module license.
[SPARC64]: Fix and re-enable dynamic TSB sizing.
[SUNSU]: Fix missing spinlock initialization.
[TG3]: Do not try to access NIC_SRAM_DATA_SIG on Sun parts.
[SPARC64]: First cut at VIS simulator for Niagara.
[SPARC64]: Fix system type in /proc/cpuinfo and remove bogus OBP check.
[SPARC64]: Add SMT scheduling support for Niagara.
[SPARC64]: Fix 32-bit truncation which broke sparsemem.
[SPARC64]: Move over to sparsemem.
[SPARC64]: Fix new context version SMP handling.
...
Sun does't put an SEEPROM behind the tigon3 chip, among other things,
so accesses to these areas just give bus timeouts.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 40-bit DMA workaround recently implemented for 5714, 5715, and
5780 needs to be expanded because there may be other tg3 devices
behind the EPB Express to PCIX bridge in the 5780 class device.
For example, some 4-port card or mother board designs have 5704 behind
the 5714.
All devices behind the EPB require the 40-bit DMA workaround.
Thanks to Chris Elmquist again for reporting the problem and testing
the patch.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Coverity checker spotted this dead code (note that (clock_ctrl == 7)
is already handled above).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan
Gary Zambrano
Adrian Bunk
Linus Torvalds
Eric Sesterhenn
David S. Miller
Jeff Mahoney
Jeff Garzik