The PCI device table in the powermac IDE driver isn't properly
terminated. Depending on how your kernel is linked and other random
factors, you can end up with this driver matched against any other PCI
device in your system, possibly crashing at boot.
Thanks to Heikki for tracking this down with me, the bug have been there
for some time, though it rarely hurts due to luck. In this case, the
switch from .22 to .23-rc9 is causing it to show up due to differences
in the resulting layout of .data I suppose.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <pmac@au1.ibm.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bitmask typo in the pdc202xx_new PLL frequency detection code
which causes it to truncate an intermediate difference to 26 bits
instead of the correct 30 bits (the PLL's bitwidth).
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Port of Alan's patch for pata_via.c.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Ensure that BLK_DEV_IDE is built-in before allowing BLK_DEV_IDE_PMAC to
be selected.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Cc: Bret Towe <magnade@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add Toshiba S1800-814 to whitelist for both pata_ali and alim15x3,
as it is correctly detected as 40-wire connected but this cable is
short enough to still use transfer modes higher than UDMA33.
Signed-off-by: Daniel Exner <dex@dragonslave.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes, so the driver needs
to account for this in the udma_filter() method. In order to achieve that, do
the following changes:
- install the method for all chips, not only HPT36x/370 and improve the code
formatting by killing the extra tabs while at it;
- add to the end of the 'switch' statement in the method cases for HPT372[AN]
and HPT374 chips upon which the known SATA cards are based;
- use hwif->ultra_mask as a default mask for the ide_dma_filter() method to
behave correctly;
- move the HPT370[A] cases below the HPT36x case for consistency.
While at it, replace the explicit UltraDMA mode masks with ATA_UDMA* constants
all over the driver...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bob Ham <rah@bash.sh>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make the SATA drive detection code from eighty_ninty_three() into inline
ide_dev_is_sata() helper fixing it along the way to be more strict while
checking word 80 for the reserved values...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
HPT374 BIOS seems to only save f_CNT register value for the function #0 before
re-tuning DPLL (that causes the driver to report obviously distorted f_CNT for
the function #1) -- fix this by always reading the saved f_CNT register value
from the function #0 in the driver's init_chipset() method.
While at it, introduce 'chip_type' for holding the 'struct hpt_info' field
of the same name and replace the structure assignment with memcpy()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver erroneously "lets go" the mate IDE chip in init_setup_pdc20270()
when ide_setup_pci_devices() call succeeds -- fix this, and drop a couple of
useless assignments in this function while at it...
Bart: keep "findev" variable initialization to silence gcc
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The IDE core never marked the PCI IDE devices as being in use after succesfull
driver probe call (the devices were marked in use only while being probed), and
so was susceptible to issues caused by unsolicited PCI hotplug device removal.
So, add pci_dev_get() call to ide_scan_pcidev() and convert this function to
the kernel style, also dropping a bunch of useless curly braces from its caller,
ide_scan_pcibus() and somewhat beautifying printk() call there, while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Currently the mpc8xx ide driver will only work on arch/ppc so only
allow it to be built there. Also, killed a minor include that isn't
actually used by the driver.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This disk reports total number of sectors instead of maximum sector address
in response to READ_NATIVE_MAX_ADDRESS command and also happily accepts
SET_MAX_ADDRESS command with the bogus value. This results in +1 sector
capacity being used and errors on attempts to use the last sector.
...
hdd: Host Protected Area detected.
    current capacity is 78165360 sectors (40020 MB)
    native  capacity is 78165361 sectors (40020 MB)
hdd: Host Protected Area disabled.
...
hdd: reading: block=78165360, sectors=1, buffer=0xc1e63000
hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdd: dma_intr: error=0x10 { SectorIdNotFound }, LBAsect=78165360, sector=78165360
...
Add hpa_list[] table and workaround the issue in idedisk_check_hpa().
v2:
* Add missing export and improve patch description a bit.
v3:
* Add list termination. (From Mikko)
Fixes kernel bugzilla bug #8816.
Thanks to Mikko for investigating the issue and helping with this patch.
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Programming DMA mode may destroy current PIO mode setting so if
CONFIG_HPT34X_AUTODMA=n (the default case) make ide_tune_dma() fail
early by disabling all host DMA masks and re-tune PIO mode.
This fix doesn't help with the driver being broken but is needed
for some other changes.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Also this host driver requires valid PCI BAR4 for normal operation so
check it in ->init_chipset and fail initialization if not set.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Also this host driver requires valid PCI BAR4 for normal operation so
check it in ->init_chipset and fail initialization if not set.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ->OUTBSYNC instead of ->OUTB when writing command register
(needed for scc_pata and pmac host drivers).
* Don't check DRDY bit of the status register on ATAPI devices
(ATAPI devices are free to ignore DRDY bit).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_in_drive_list() from ide-dma.c to ide-iops.c.
* Add ivb_list[] table for listening early UDMA66 devices which don't conform
to ATA4 standard wrt cable detection (bit14 is zero, only bit13 is valid)
and use only device side cable detection for them since host side cable
detection may be unreliable.
* Add model "QUANTUM FIREBALLlct10 05" with firwmare "A03.0900" to the list
(from Craig's bugreport).
v2:
* Improve kernel message basing on suggestion from Sergei.
v3:
* Don't print kernel message when no device side cable detection is done,
plus some minor fixes. (Noticed by Sergei)
Thanks to Craig for testing this patch.
Cc: Craig Block <chblock3@yahoo.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
pmac_ide_tune_chipset() don't set drive->init_speed.
Fix it by setting drive->{current,init}_speed in pmac_ide_do_setfeature()
and clean up pmac_ide_{tune_chipset,mdma_enable,udma_enable}().
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add DMA blacklist checking (->ide_dma_on check probably can go now).
* Add ->atapi_dma flag checking and remove no longer needed
ns87415_ide_dma_check() from ns87415 host driver.
* Remove now needless __ide_dma_check() wrapper and symbol export.
* Check drive->autodma instead of hwif->autodma (there should be no changes in
behavior as all users of config_drive_for_dma() set both ->autodma flags).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some host drivers depend on CONFIG_IDE_GENERIC to do the probing but their
config options lack explicit dependencies on IDE_GENERIC. In the long-term
these host drivers should be fixed to do the probing themselves but for now
fix them by making their config options select CONFIG_IDE_GENERIC.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
These days, CONFIG_IDE_GENERIC causes more confusion and
misconfiguration than it helps. Especially so because libata is
linked after the generic driver. Default to N.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: "P.C.Chan" <pc.chan@alcatel-lucent.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use pio == 255 == "auto-tune" in scc_config_drive_for_dma() instead of
forcing PIO4 on PIO fallback. Fix comment while at it.
* Rename scc_tuneproc() to scc_tune_pio() and add scc_tuneproc() wrapper.
Move finding of the best PIO mode and setting of transfer mode on the device
to the new wrapper.
* Fix scc_tune_chipset() to tune PIO modes. Do a small cleanup while at it.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Don't call {piix,slc90e66}_dma_2_pio() for PIO modes in
{piix,slc90e66}_tune_chipset().
* Add PIO1 handling to {piix,slc90e66}_tune_chipset().
* Bump driver version.
v2:
* Remove PIO modes from {piix,slc90e66}_dma_2_pio(), they are no longer needed
there (Noticed by Sergei)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set transfer mode on the device in jmicron_tuneproc(),
also add pio == 255 == "auto-tune" handling.
* Use jmicron_tuneproc() in jmicron_config_drive_for_dma().
* Remove no longer needed config_jmicron_chipset_for_pio().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename it8213_tuneproc() to it8213_tune_pio() and add it8213_tuneproc()
wrapper. Move finding of the best PIO mode to the new wrapper.
* Add setting of transfer mode on the device to it8213_tuneproc().
* Don't call it8213_dma_2_pio() for PIO modes in it8213_tune_chipset().
* Use it8213_tuneproc() in it8213_config_drive_for_dma().
v2:
* Remove PIO modes from it8213_dma_2_pio(), they are no longer needed there
(Noticed by Sergei)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix cs5535_tuneproc() to pass PIO transfer mode value instead of PIO mode
number to cs5535_set_speed() (fixes random PIO timings being programmed
and a possible OOPS). Do a little cleanup while at it.
* Fix cs5535_set_speed() to check if the mate device is present (fixes PIO0
taskfile timings being used if there is no other device on the cable).
* Use cs5535_tuneproc() in cs5535_dma_check(). The old code had the same
issue as cs5535_tuneproc() and add additionally caused 0x00-0x04 transfer
mode values (== default PIO, default PIO w/ IORDY + two invalid values)
being set on the device instead of values 0x08-0x0c (XFER_PIO_[0,4]).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Is this a bug? In original verison memset cleared sizeof(state) bytes
instead of sizeof(*state). If it was intentional then this patch is invalid.
If not intentional -> valid :) Please review.
Bart: Yes, it is a bug so this patch is a valid bugfix. :-)
drivers/ide/arm/icside.c | 18883 -> 18849 (-34 bytes)
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
drivers/ide/ide-tape.c: In function '__idetape_kmalloc_stage':
drivers/ide/ide-tape.c:2588: warning: large integer implicitly truncated to unsigned type
drivers/ide/ide-tape.c:2616: warning: large integer implicitly truncated to unsigned type
b_size in struct idetape_bh is an unsigned short. We sometimes assigne
PAGE_SIZE to it and PAGE_SIZE can be 64K or larger, so make it a u32.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix a couple of runtogether printks in cmd64x.c IDE driver by adding
proper newlines.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Recognise the FSC Amilo A1630's incarnation of a SiS5513 chip as laptop to
get UDMA100 support.
Signed-off-by: David Lamparter <equinox@diac24.net>
Cc: Lionel Bouton <Lionel.Bouton@inet6.fr>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
As found by the Coverity checker, and reported by Adrian Bunk, this
fixes a overrun error in the CS5535 IDE driver. Somebody got a little
excited with the if() statement - the CS5535 only supports UDMA 0-4.
Bart:
Not a bug per se since the upper layer will never feed this function
with speed > XFER_UDMA_4 (thanks to ->ultra_mask being set to 0x1f).
Worth fixing anyway.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The arm26 port has been in a state where it was far from even compiling
for quite some time.
Ian Molton agreed with the removal.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Now that ide-floppy supports SG_IO we can add support for SCSI ioctls
(except deprecated SCSI_IOCTL_SEND_COMMAND and legacy CDROM_SEND_PACKET
ones - we can add them later iff really needed).
While at it remove handling of CDROMEJECT and CDROMCLOSETRAY ioctls from
generic_ide_ioctl():
- This prevents ide-{disk,tape,scsi} device drivers from obtaining
REQ_TYPE_BLOCK_PC type requests which are currently unsupported by
these drivers and which are potentially harmful (as reported by Andrew).
- There is no functionality loss since aforementioned ioctls will now be
handled by idefloppy_ioctl()->scsi_cmd_ioctl() (for devices using
ide-floppy driver) and by idecd_ioctl->cdrom_ioctl()->scsi_cmd_ioctl()
(for devices using ide-cd driver).
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ATA_PIO[0-6] defines to <linux/ata.h>.
* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.
* Add PIO masks to host drivers.
<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->host_flags to ide_hwif_t to store ide_pci_device_t.host_flags,
assign it in setup-pci.c:ide_pci_setup_ports().
* Add IDE_HFLAG_PIO_NO_{BLACKLIST,DOWNGRADE} to ide_pci_device_t.host_flags
and teach ide_get_best_pio_mode() about them. Also remove needless
!drive->id check while at it (drive->id is always present).
* Convert amd74xx, via82cxxx and ide-timing.h to use ide_get_best_pio_mode()
and then remove no longer needed ide_find_best_pio_mode().
There should be no functionality changes caused by this patch.
Acked-by: Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Drop no longer needed "PIO data" argument from ide_get_best_pio_mode()
and convert all users accordingly.
* Remove no longer needed ide_pio_data_t.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Benjamin Herrenschmidt
Stephen Rothwell
Jorge Juan Chico
Mikael Pettersson
Bartlomiej Zolnierkiewicz
Tony Breeds
Daniel Exner
Sergei Shtylyov
Kumar Gala
Joseph Chan
Tejun Heo
Mariusz Kozlowski
Meelis Roos
David Lamparter
Jordan Crouse
Adrian Bunk
Al Viro
Jens Axboe