On hardware like the T61 it can take a couple of seconds for the battery
to start charging after the power is connected, and we incorrectly tell
userspace that we are fully charged, and then go back to charging.
Only mark a battery as fully charged when the preset charge matches either
the last full charge, or the design charge.
http://bugzilla.kernel.org/show_bug.cgi?id=12632
Signed-off-by: Richard Hughes <hughsient@gmail.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
update of battery info fields is required.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Andy Neitzke <neitzke@ias.edu>
Signed-off-by: Alexey Starikovskiy <astarikovskiy <at> suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit 558073dd56, along with
the failed try to fix the regression it caused ("ACPI: Fix ACPI battery
regression introduced by commit 558073"), which just made things worse.
Commit aaad077638 (that failed "Fix ACPI
battery regression") got the voltage conversion confused, and fixed the
problem with Rafael's battery monitor apparently just by mistake.
So revert them both, getting us back to the 2.6.27 state in this, and
let's revisit it when people understand what's going on.
Noted-by: Paul Martin <pm@debian.org>
Requested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <len.brown@intel.com>
Cc: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 558073dd56 ("ACPI: battery: Convert
discharge energy rate to current properly") caused the battery subsystem
to report wrong values of the remaining time on battery power and the
time until fully charged on Toshiba Portege R500 (and presumably on
other boxes too).
Fix the issue by correcting the conversion from mW to mA.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ACPI battery interface reports its state either in mW or in mA, and
discharge rate in your case is reported in mW. power_supply interface
does not have such a parameter, so current_now parameter is used
for all cases. But in case of mW, reported discharge should
be converted into mA.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Len Brown <len.brown@intel.com>
Move all the component definitions for drivers to a single shared place,
include/acpi/acpi_drivers.h.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
We want to submit a patch to -next, which will remove bus_id from
"struct device", to find the remaining pieces to convert, and finally
switch over to the new api, which will remove the 20 bytes array
and does no longer have a size limitation.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Tejun's commit 7b595756ec made sysfs
attribute->owner unnecessary. But the field was left in the structure to
ease the merge. It's been over a year since that change and it is now
time to start killing attribute->owner along with its users - one arch at
a time!
This patch is attempt #1 to get rid of attribute->owner only for
CONFIG_X86_64 or CONFIG_X86_32 . We will deal with other arches later on
as and when possible - avr32 will be the next since that is something I
can test. Compile (make allyesconfig / make allmodconfig / custom config)
and boot tested.
akpm: the idea is that we put the declaration of sttribute.owner inside
`#ifndef CONFIG_X86'. But that proved to be too ambitious for now because
new usages kept on turning up in subsystem trees.
[akpm: remove the ifdef for now]
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Catch attempts to use of acpi_driver_data on pointers of wrong type.
akpm: rewritten to use proper C typechecking and remove the
"function"-used-as-lvalue thing.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Add correct ->owner to proc_fops to fix reading/module unloading race.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acer BIOS has a bug which is exposed when a dead battery is present.
The package template that is used to describe battery status is
over-written with sane values when the battery is live.
But when the batter is dead, a bogus reference in the template
is used. In this case, Linux returns a fault, when instead
it should simply return that it doesn't know the missing value.
http://bugzilla.kernel.org/show_bug.cgi?id=8573http://bugzilla.kernel.org/show_bug.cgi?id=10202
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
egrep serial /proc/acpi/battery/BAT0/info
serial number: 32090
serial number can tell you from the imminent danger
of beeing set on fire.
Signed-off-by: maximilian attems <max@stro.at>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
At least some systems report technology information with trailing spaces:
{pts/1}% cat -E /var/tmp/bat/2.6.23 | grep type
battery type: Li-ION $
Use strncasecmp to compare model string to skip trailing part
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce new ACPI_PROCFS_POWER (default Yes) config option and move
procfs code in battery, ac, and sbs drivers under it.
This is done to allow ACPI_PROCFS to be default No.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
get_property() should not call battery_update(), it also should call
get_status() only if battery is present to avoid cycle and oops.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Acked-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a battery is at a critical charge level and not being charged or
discharged, then the ACPI _BST method will return a state of 4, and
the current acpi_battery_get_property() code will not set any property
value for POWER_SUPPLY_PROP_STATUS. This will cause an oops in
power_supply_show_property() when it reads off the end of the
status_text array. This actually was causing a 100% reproducible
crash on boot on my laptop with two batteries, when one battery was
completely drained and the laptop was not plugged in.
Fix this by making sure acpi_battery_get_property() returns
POWER_SUPPLY_STATUS_UNKNOWN for any battery state it doesn't already
handle explicitly. There doesn't seem to be any status enum value
defined that makes more sense than 'unknown' for a battery at a
critical charge level.
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <lenb@t61.(none)>
Some machines return integer instead of expected string.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Len Brown <len.brown@intel.com>
Support Li-Ion as possible name for technology.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Make sure no power_supply object is present unless we actualy detect
presence of battery. This fixes ghost batteries detected by HAL
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
After commit f1d4661abe this was dead
code.
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Refer to Documentation/power_supply_class.txt for interface description.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_extract_package() creates more problems with memory management than
it solves as helper for package handling.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Schedule /proc/acpi/event for removal in 6 months.
Re-name acpi_bus_generate_event() to acpi_bus_generate_proc_event()
to make sure there is no confusion that it is for /proc/acpi/event only.
Add CONFIG_ACPI_PROC_EVENT to allow removal of /proc/acpi/event.
There is no functional change if CONFIG_ACPI_PROC_EVENT=y
Signed-off-by: Len Brown <len.brown@intel.com>
The previous events patch added a netlink event for every
user of the legacy /proc/acpi/event interface.
However, some users of /proc/acpi/event are really input events,
and they already report their events via the input layer.
Introduce a new interface, acpi_bus_generate_netlink_event(),
which is explicitly called by devices that want to repoprt
events via netlink. This allows the input-like events
to opt-out of generating netlink events. In summary:
events that are sent via netlink:
ac/battery/sbs
thermal
processor
thinkpad_acpi dock/bay
events that are sent via input layer:
button
video hotkey
thinkpad_acpi hotkey
asus_acpi/asus-laptop hotkey
sonypi/sonylaptop
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit 3bd92ba19a.
It is no longer necessary, and it opens up a race.
Acked-by: Vladimir Lebedev <vladimir.p.lebedev@gmail.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
modpost is going to use these to create e.g. acpi:ACPI0001
in modules.alias.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
In response to review comments from Andrew Morton
Signed-off-by: Alexey Starikovskiy <aystarik@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
/proc exports _BST in a single file, and _BST is re-evaulated
whenever that file is read.
Sometimes user-space reads this file frequently, and on some
systems _BST takes a long time to evaluate due to a slow EC.
Further, when we move to sysfs, the values returned from _BST
will be in multiple files, and evaluating _BST for each
file read would make matters worse.
Here code is added to support caching the results of _BST.
A new module parameter "update_time" tells how many seconds the
cached _BST should be used before it is re-evaluated.
Currently, update_time defaults to 0, and so the
existing behaviour of re-evaluating on each read retained.
Signed-off-by: Vladimir Lebedev <vladimir.p.lebedev@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cleanup -- No functional changes.
Battery state is currently exported in a proc "state" file.
Update associated #defines and routines to be consistent.
Signed-off-by: Vladimir Lebedev <vladimir.p.lebedev@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
It was erroneously used as a description rather than a name.
ie. turn this:
lenb@se7525gp2:/sys> ls bus/acpi/drivers
ACPI AC Adapter Driver ACPI Embedded Controller Driver ACPI Power Resource Driver
ACPI Battery Driver ACPI Fan Driver ACPI Processor Driver
ACPI Button Driver ACPI PCI Interrupt Link Driver ACPI Thermal Zone Driver
ACPI container driver ACPI PCI Root Bridge Driver hpet
into this:
lenb@se7525gp2:~> ls /sys/bus/acpi/drivers
ac battery button container ec fan hpet pci_link pci_root power processor thermal
Signed-off-by: Len Brown <len.brown@intel.com>
cosmetic only
Make "module name" actually match the file name.
Invoke with ';' as leaving it off confuses Lindent and gcc doesn't care.
Fix indentation where Lindent did get confused.
Signed-off-by: Len Brown <len.brown@intel.com>
Richard Hughes
Alexey Starikovskiy
Linus Torvalds
Rafael J. Wysocki
Alexey Starikovskiy
Len Brown
Bjorn Helgaas
Kay Sievers
Parag Warudkar
Pavel Machek
Denis V. Lunev
maximilian attems
Andrey Borzenkov
Roland Dreier
Adrian Bunk
Zhang Rui
Alexey Starikovskiy
Thomas Renninger
Vladimir Lebedev
Vladimir Lebedev
Burman Yan