Inserting an SD-card on an Intel NUC10i3FNK4 (which contains a GL9755)
results in the message:
mmc0: 1.8V regulator output did not become stable
Following this message, some cards work (sometimes), but most cards fail
with EILSEQ. This behaviour is observed on Debian 10 running kernel
4.19.188, but also with 5.8.18 and 5.11.15.
The driver currently waits 5ms after switching on the 1.8V regulator for
it to become stable. Increasing this to 10ms gets rid of the warning
about stability, but most cards still fail. Increasing it to 20ms gets
some cards working (a 32GB Samsung micro SD works, a 128GB ADATA
doesn't). At 50ms, the ADATA works most of the time, and at 100ms both
cards work reliably.
Signed-off-by: Daniel Beer <dlbeer@gmail.com>
Acked-by: Ben Chuang <benchuanggli@gmail.com>
Fixes: e51df6ce66 ("mmc: host: sdhci-pci: Add Genesys Logic GL975x support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210424081652.GA16047@nyquist.nev
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The brcmfmac driver can generate a scatterlist from a skb with each packets
not aligned to the block size. This is not supported by the Amlogic Descriptor
dma engine where each descriptor must match a multiple of the block size.
The sg list is valid, since the sum of the sg buffers is a multiple of the
block size, but we must discard those when in SD_IO_RW_EXTENDED mode since
SDIO block mode can be used under the hood even with data->blocks == 1.
Those transfers are very rare, thus can be replaced by a bounce buffer
without real performance loss.
Fixes: 7412dee9f1 ("mmc: meson-gx: replace WARN_ONCE with dev_warn_once about scatterlist size alignment in block mode")
Cc: stable@vger.kernel.org
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210426175559.3110575-2-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some drivers like ath10k can sometimg give an sg buffer with an offset whose alignment
is not compatible with the Amlogic DMA descriptor engine requirements.
Simply replace with dev_warn_once() to inform user this should be fixed to avoid
degraded performance.
This should be ultimately fixed in ath10k, but since it's only a performance issue
the warning should be removed.
Fixes: 79ed05e329 ("mmc: meson-gx: add support for descriptor chain mode")
Cc: stable@vger.kernel.org
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210426175559.3110575-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Fix hanging on I/O during system suspend for removable cards
- Set read only for SD cards with permanent write protect bit
- Power cycle the SD/SDIO card if CMD11 fails for UHS voltage
- Issue a cache flush for eMMC only when it's enabled
- Adopt to updated cache ctrl settings for eMMC from MMC ioctls
- Use use device property API when parsing voltages
- Don't retry eMMC sanitize cmds
- Use the timeout from the MMC ioctl for eMMC santize cmds
MMC host:
- mmc_spi: Make of_mmc_spi.c resource provider agnostic
- mmc_spi: Use polling for card detect even without voltage-ranges
- sdhci: Check for reset prior to DMA address unmap
- sdhci-acpi: Add support for the AMDI0041 eMMC controller variant
- sdhci-esdhc-imx: Depending on OF Kconfig and cleanup code
- sdhci-pci: Add PCI IDs for Intel LKF
- sdhci-pci: Fix initialization of some SD cards for Intel BYT
- sdhci-pci-gli: Various improvements for GL97xx variants
- sdhci-of-dwcmshc: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- sdhci-of-dwcmshc: Add ACPI support for BlueField-3 SoC
- sdhci-of-dwcmshc: Add Rockchip platform support
- tmio/renesas_sdhi: Extend support for reset and use a reset controller
- tmio/renesas_sdhi: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- tmio/renesas_sdhi: Various improvements
MEMSTICK:
- Minor improvements/cleanups.
-----BEGIN PGP SIGNATURE-----
iQJLBAABCgA1FiEEugLDXPmKSktSkQsV/iaEJXNYjCkFAmCJIGkXHHVsZi5oYW5z
c29uQGxpbmFyby5vcmcACgkQ/iaEJXNYjCnX+w//fvTbFsekv/bYZQoiDDGngbg0
LGUfTZPOLWuzHpiQSY5RjRHvt9CFOc07N96RAqxeqgJ3LS2WzIQSn9asK+5EupXH
CVnWKcYBs+1KthMCRsXjduXILztSQFJGbgO8DYrqvwu9mg6SU3ExfqNhX0O+D0ed
GhzQ55yJTitRpa8S2FYQcirl+clV/5+o3uC82nvaoVR1baE1+catNJ028k/Nd0XE
dFboEE6IJ4qndLWAyBnijYMXbLq/HKmqjeNsR5tooAA/QcXf9tQKqHtdim1N1Cac
THF3hGHMskw7bM4PoupzeJYHzYmL6UINkw192BLMNsGCHidflWTarjUR/5Y2OEz1
eKG5GX+Ww+fdsupN8h448rI1h3EcKJlQFvit9/OIcHS8r7ZeouWNXElH3WUpc3i4
pb3yHBBNMQ3rn0wUfjZh2sggyy+/pRAY1OPfeDud1wggRjg/xVMY3nxpqQmFRKZM
C2/mPUMxaY7zHb9AzCOYCjhgjTPh4HrzIRZeqnZ1FRGuv0yLDG46hc1ufLggCx5P
v1RGB2vJ2hGyWIqvBXw1nF8RwiOCXYXPyZjehWU0K6zryGQPq275/6ziFvL+Nh4U
8liwwHeeIQNvPs7HNzSQ1rXo8elNRvWkqZpvCqTWgJCX4/NFYQTj+Lq2T2EiTxWt
dlr9RLlARJEeutA07rM=
=WL87
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC and MEMSTICK updates from Ulf Hansson:
"MMC core:
- Fix hanging on I/O during system suspend for removable cards
- Set read only for SD cards with permanent write protect bit
- Power cycle the SD/SDIO card if CMD11 fails for UHS voltage
- Issue a cache flush for eMMC only when it's enabled
- Adopt to updated cache ctrl settings for eMMC from MMC ioctls
- Use use device property API when parsing voltages
- Don't retry eMMC sanitize cmds
- Use the timeout from the MMC ioctl for eMMC santize cmds
MMC host:
- mmc_spi: Make of_mmc_spi.c resource provider agnostic
- mmc_spi: Use polling for card detect even without voltage-ranges
- sdhci: Check for reset prior to DMA address unmap
- sdhci-acpi: Add support for the AMDI0041 eMMC controller variant
- sdhci-esdhc-imx: Depending on OF Kconfig and cleanup code
- sdhci-pci: Add PCI IDs for Intel LKF
- sdhci-pci: Fix initialization of some SD cards for Intel BYT
- sdhci-pci-gli: Various improvements for GL97xx variants
- sdhci-of-dwcmshc: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- sdhci-of-dwcmshc: Add ACPI support for BlueField-3 SoC
- sdhci-of-dwcmshc: Add Rockchip platform support
- tmio/renesas_sdhi: Extend support for reset and use a reset controller
- tmio/renesas_sdhi: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- tmio/renesas_sdhi: Various improvements
MEMSTICK:
- Minor improvements/cleanups"
* tag 'mmc-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (79 commits)
mmc: block: Issue a cache flush only when it's enabled
memstick: r592: ignore kfifo_out() return code again
mmc: block: Update ext_csd.cache_ctrl if it was written
mmc: mmc_spi: Make of_mmc_spi.c resource provider agnostic
mmc: mmc_spi: Use already parsed IRQ
mmc: mmc_spi: Drop unused NO_IRQ definition
mmc: mmc_spi: Set up polling even if voltage-ranges is not present
mmc: core: Convert mmc_of_parse_voltage() to use device property API
mmc: core: Correct descriptions in mmc_of_parse()
mmc: dw_mmc-rockchip: Just set default sample value for legacy mode
mmc: sdhci-s3c: constify uses of driver/match data
mmc: sdhci-s3c: correct kerneldoc of sdhci_s3c_drv_data
mmc: sdhci-s3c: simplify getting of_device_id match data
mmc: tmio: always restore irq register
mmc: sdhci-pci-gli: Enlarge ASPM L1 entry delay of GL975x
mmc: core: Let eMMC sanitize not retry in case of timeout/failure
mmc: core: Add a retries parameter to __mmc_switch function
memstick: r592: remove unused variable
mmc: sdhci-st: Remove unnecessary error log
mmc: sdhci-msm: Remove unnecessary error log
...
- Add idle states table for IceLake-D to the intel_idle driver and
update IceLake-X C6 data in it (Artem Bityutskiy).
- Fix the C7 idle state on Tegra114 in the tegra cpuidle driver and
drop the unused do_idle() firmware call from it (Dmitry Osipenko).
- Fix cpuidle-qcom-spm Kconfig entry (He Ying).
- Fix handling of possible negative tick_nohz_get_next_hrtimer()
return values of in cpuidle governors (Rafael Wysocki).
- Add support for frequency-invariance to the ACPI CPPC cpufreq
driver and update the frequency-invariance engine (FIE) to use it
as needed (Viresh Kumar).
- Simplify the default delay_us setting in the ACPI CPPC cpufreq
driver (Tom Saeger).
- Clean up frequency-related computations in the intel_pstate
cpufreq driver (Rafael Wysocki).
- Fix TBG parent setting for load levels in the armada-37xx
cpufreq driver and drop the CPU PM clock .set_parent method for
armada-37xx (Marek Behún).
- Fix multiple issues in the armada-37xx cpufreq driver (Pali Rohár).
- Fix handling of dev_pm_opp_of_cpumask_add_table() return values
in cpufreq-dt to take the -EPROBE_DEFER one into acconut as
appropriate (Quanyang Wang).
- Fix format string in ia64-acpi-cpufreq (Sergei Trofimovich).
- Drop the unused for_each_policy() macro from cpufreq (Shaokun
Zhang).
- Simplify computations in the schedutil cpufreq governor to avoid
unnecessary overhead (Yue Hu).
- Fix typos in the s5pv210 cpufreq driver (Bhaskar Chowdhury).
- Fix cpufreq documentation links in Kconfig (Alexander Monakov).
- Fix PCI device power state handling in pci_enable_device_flags()
to avoid issuse in some cases when the device depends on an ACPI
power resource (Rafael Wysocki).
- Add missing documentation of pm_runtime_resume_and_get() (Alan
Stern).
- Add missing static inline stub for pm_runtime_has_no_callbacks()
to pm_runtime.h and drop the unused try_to_freeze_nowarn()
definition (YueHaibing).
- Drop duplicate struct device declaration from pm.h and fix a
structure type declaration in intel_rapl.h (Wan Jiabing).
- Use dev_set_name() instead of an open-coded equivalent of it in
the wakeup sources code and drop a redundant local variable
initialization from it (Andy Shevchenko, Colin Ian King).
- Use crc32 instead of md5 for e820 memory map integrity check
during resume from hibernation on x86 (Chris von Recklinghausen).
- Fix typos in comments in the system-wide and hibernation support
code (Lu Jialin).
- Modify the generic power domains (genpd) code to avoid resuming
devices in the "prepare" phase of system-wide suspend and
hibernation (Ulf Hansson).
- Add Hygon Fam18h RAPL support to the intel_rapl power capping
driver (Pu Wen).
- Add MAINTAINERS entry for the dynamic thermal power management
(DTPM) code (Daniel Lezcano).
- Add devm variants of operating performance points (OPP) API
functions and switch over some users of the OPP framework to
the new resource-managed API (Yangtao Li and Dmitry Osipenko).
- Update devfreq core:
* Register devfreq devices as cooling devices on demand (Daniel
Lezcano).
* Add missing unlock opeation in devfreq_add_device() (Lukasz
Luba).
* Use the next frequency as resume_freq instead of the previous
frequency when using the opp-suspend property (Dong Aisheng).
* Check get_dev_status in devfreq_update_stats() (Dong Aisheng).
* Fix set_freq path for the userspace governor in Kconfig (Dong
Aisheng).
* Remove invalid description of get_target_freq() (Dong Aisheng).
- Update devfreq drivers:
* imx8m-ddrc: Remove imx8m_ddrc_get_dev_status() and unneeded
of_match_ptr() (Dong Aisheng, Fabio Estevam).
* rk3399_dmc: dt-bindings: Add rockchip,pmu phandle and drop
references to undefined symbols (Enric Balletbo i Serra, Gaël
PORTAY).
* rk3399_dmc: Use dev_err_probe() to simplify the code (Krzysztof
Kozlowski).
* imx-bus: Remove unneeded of_match_ptr() (Fabio Estevam).
- Fix kernel-doc warnings in three places (Pierre-Louis Bossart).
- Fix typo in the pm-graph utility code (Ricardo Ribalda).
-----BEGIN PGP SIGNATURE-----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=t+SG
-----END PGP SIGNATURE-----
Merge tag 'pm-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add some new hardware support (for example, IceLake-D idle
states in intel_idle), fix some issues (for example, the handling of
negative "sleep length" values in cpuidle governors), add new
functionality to the existing drivers (for example, scale-invariance
support in the ACPI CPPC cpufreq driver) and clean up code all over.
Specifics:
- Add idle states table for IceLake-D to the intel_idle driver and
update IceLake-X C6 data in it (Artem Bityutskiy).
- Fix the C7 idle state on Tegra114 in the tegra cpuidle driver and
drop the unused do_idle() firmware call from it (Dmitry Osipenko).
- Fix cpuidle-qcom-spm Kconfig entry (He Ying).
- Fix handling of possible negative tick_nohz_get_next_hrtimer()
return values of in cpuidle governors (Rafael Wysocki).
- Add support for frequency-invariance to the ACPI CPPC cpufreq
driver and update the frequency-invariance engine (FIE) to use it
as needed (Viresh Kumar).
- Simplify the default delay_us setting in the ACPI CPPC cpufreq
driver (Tom Saeger).
- Clean up frequency-related computations in the intel_pstate cpufreq
driver (Rafael Wysocki).
- Fix TBG parent setting for load levels in the armada-37xx cpufreq
driver and drop the CPU PM clock .set_parent method for armada-37xx
(Marek Behún).
- Fix multiple issues in the armada-37xx cpufreq driver (Pali Rohár).
- Fix handling of dev_pm_opp_of_cpumask_add_table() return values in
cpufreq-dt to take the -EPROBE_DEFER one into acconut as
appropriate (Quanyang Wang).
- Fix format string in ia64-acpi-cpufreq (Sergei Trofimovich).
- Drop the unused for_each_policy() macro from cpufreq (Shaokun
Zhang).
- Simplify computations in the schedutil cpufreq governor to avoid
unnecessary overhead (Yue Hu).
- Fix typos in the s5pv210 cpufreq driver (Bhaskar Chowdhury).
- Fix cpufreq documentation links in Kconfig (Alexander Monakov).
- Fix PCI device power state handling in pci_enable_device_flags() to
avoid issuse in some cases when the device depends on an ACPI power
resource (Rafael Wysocki).
- Add missing documentation of pm_runtime_resume_and_get() (Alan
Stern).
- Add missing static inline stub for pm_runtime_has_no_callbacks() to
pm_runtime.h and drop the unused try_to_freeze_nowarn() definition
(YueHaibing).
- Drop duplicate struct device declaration from pm.h and fix a
structure type declaration in intel_rapl.h (Wan Jiabing).
- Use dev_set_name() instead of an open-coded equivalent of it in the
wakeup sources code and drop a redundant local variable
initialization from it (Andy Shevchenko, Colin Ian King).
- Use crc32 instead of md5 for e820 memory map integrity check during
resume from hibernation on x86 (Chris von Recklinghausen).
- Fix typos in comments in the system-wide and hibernation support
code (Lu Jialin).
- Modify the generic power domains (genpd) code to avoid resuming
devices in the "prepare" phase of system-wide suspend and
hibernation (Ulf Hansson).
- Add Hygon Fam18h RAPL support to the intel_rapl power capping
driver (Pu Wen).
- Add MAINTAINERS entry for the dynamic thermal power management
(DTPM) code (Daniel Lezcano).
- Add devm variants of operating performance points (OPP) API
functions and switch over some users of the OPP framework to the
new resource-managed API (Yangtao Li and Dmitry Osipenko).
- Update devfreq core:
* Register devfreq devices as cooling devices on demand (Daniel
Lezcano).
* Add missing unlock opeation in devfreq_add_device() (Lukasz
Luba).
* Use the next frequency as resume_freq instead of the previous
frequency when using the opp-suspend property (Dong Aisheng).
* Check get_dev_status in devfreq_update_stats() (Dong Aisheng).
* Fix set_freq path for the userspace governor in Kconfig (Dong
Aisheng).
* Remove invalid description of get_target_freq() (Dong Aisheng).
- Update devfreq drivers:
* imx8m-ddrc: Remove imx8m_ddrc_get_dev_status() and unneeded
of_match_ptr() (Dong Aisheng, Fabio Estevam).
* rk3399_dmc: dt-bindings: Add rockchip,pmu phandle and drop
references to undefined symbols (Enric Balletbo i Serra, Gaël
PORTAY).
* rk3399_dmc: Use dev_err_probe() to simplify the code (Krzysztof
Kozlowski).
* imx-bus: Remove unneeded of_match_ptr() (Fabio Estevam).
- Fix kernel-doc warnings in three places (Pierre-Louis Bossart).
- Fix typo in the pm-graph utility code (Ricardo Ribalda)"
* tag 'pm-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
PM: wakeup: remove redundant assignment to variable retval
PM: hibernate: x86: Use crc32 instead of md5 for hibernation e820 integrity check
cpufreq: Kconfig: fix documentation links
PM: wakeup: use dev_set_name() directly
PM: runtime: Add documentation for pm_runtime_resume_and_get()
cpufreq: intel_pstate: Simplify intel_pstate_update_perf_limits()
cpufreq: armada-37xx: Fix module unloading
cpufreq: armada-37xx: Remove cur_frequency variable
cpufreq: armada-37xx: Fix determining base CPU frequency
cpufreq: armada-37xx: Fix driver cleanup when registration failed
clk: mvebu: armada-37xx-periph: Fix workaround for switching from L1 to L0
clk: mvebu: armada-37xx-periph: Fix switching CPU freq from 250 Mhz to 1 GHz
cpufreq: armada-37xx: Fix the AVS value for load L1
clk: mvebu: armada-37xx-periph: remove .set_parent method for CPU PM clock
cpufreq: armada-37xx: Fix setting TBG parent for load levels
cpuidle: Fix ARM_QCOM_SPM_CPUIDLE configuration
cpuidle: tegra: Remove do_idle firmware call
cpuidle: tegra: Fix C7 idling state on Tegra114
PM: sleep: fix typos in comments
cpufreq: Remove unused for_each_policy macro
...
In command queueing mode, the cache isn't flushed via the mmc_flush_cache()
function, but instead by issuing a CMDQ_TASK_MGMT (CMD48) with a
FLUSH_CACHE opcode. In this path, we need to check if cache has been
enabled, before deciding to flush the cache, along the lines of what's
being done in mmc_flush_cache().
To fix this problem, let's add a new bus ops callback ->cache_enabled() and
implement it for the mmc bus type. In this way, the mmc block device driver
can call it to know whether cache flushing should be done.
Fixes: 1e8e55b670 (mmc: block: Add CQE support)
Cc: stable@vger.kernel.org
Reported-by: Brendan Peter <bpeter@lytx.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Tested-by: Brendan Peter <bpeter@lytx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210425060207.2591-2-avri.altman@wdc.com
Link: https://lore.kernel.org/r/20210425060207.2591-3-avri.altman@wdc.com
[Ulf: Squashed the two patches and made some minor updates]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The cache function can be turned ON and OFF by writing to the CACHE_CTRL
byte (EXT_CSD byte [33]). However, card->ext_csd.cache_ctrl is only
set on init if cache size > 0.
Fix that by explicitly setting ext_csd.cache_ctrl on ext-csd write.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210420134641.57343-3-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SPI core already parses and maps IRQ for us if provided.
Use it instead of double parsing in mmc_spi_get_pdata().
Due to above, change condition, since SPI core can hold
an error pointer as invalid IRQ.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210419112459.25241-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After the commit 073350f7b5 ("mmc: mmc_spi: Fix return value evaluation of
irq_of_parse_and_map()") the NO_IRQ is not used anymore, drop it for good.
Fixes: 073350f7b5 ("mmc: mmc_spi: Fix return value evaluation of irq_of_parse_and_map()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210419112459.25241-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When voltage-ranges property is not present the driver assumes that
it is 3.3v (3.2v..3.4v). But at the same time it disallows polling.
Fix that by dropping the comparison to 0 when no property is provided.
While at it, mark voltage-ranges property optional as it was initially.
Fixes: 9c43df5791 ("mmc_spi: Add support for OpenFirmware bindings")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210419112459.25241-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_of_parse() for a few years has been using device property API.
Convert mmc_of_parse_voltage() as well.
At the same time switch users to new API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210419112459.25241-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since it has been converted to use device property API, the function
and field descriptions become outdated. Correct them.
Fixes: 73a47a9bb3 ("mmc: core: Use device_property_read instead of of_property_read")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210419112459.25241-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit e085b51c74 ("mmc: meson-gx: check for scatterlist size alignment in block mode"),
support for SDIO SD_IO_RW_EXTENDED transferts are properly filtered but some driver
like brcmfmac still gives a block sg buffer size not aligned with SDIO block,
triggerring a WARN_ONCE() with scary stacktrace even if the transfer works fine
but with possible degraded performances.
Simply replace with dev_warn_once() to inform user this should be fixed to avoid
degraded performance.
This should be ultimately fixed in brcmfmac, but since it's only a performance issue
the warning should be removed.
Fixes: e085b51c74 ("mmc: meson-gx: check for scatterlist size alignment in block mode")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210416094347.2015896-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
.set_ios() is called from .resume() as well. For SDIO device which sets
keep-power-in-suspend, nothing should be changed after resuming, as well
as sample tuning value, since this value is tuned already. So we should
not overwrite it with the default value.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/1618539454-182170-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver data (struct sdhci_s3c_drv_data) stored in of_device_id
table is allocated as const and used only in const-way. Skip
unnecessary const-away casts and convert all users to work with pointer
to const. This is both more logical and safer.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210415084412.51125-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Correct the name of sdhci_s3c_drv_data structure in kerneldoc:
drivers/mmc/host/sdhci-s3c.c:143: warning:
expecting prototype for struct sdhci_s3c_driver_data. Prototype was for struct sdhci_s3c_drv_data instead
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210415084412.51125-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use of_device_get_match_data() to make the code slightly smaller and to
remove the of_device_id table forward declaration.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210415084412.51125-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, only SDHI on R-Car Gen2+ reinitializes the irq register
during reset but it should be done on all instances. We can move it from
the SDHI driver to the TMIO core, because we now have the
'sd_irq_mask_all' variable which carries the proper value to use. That
also means we can remove the initialization from tmio_mmc_probe()
because it calls tmio_mmc_reset(), too. We only move that
tmio_mmc_reset() call there a little to ensure 'sd_irq_mask_all' is
properly set.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210413083137.11171-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
GL975x enters ASPM L1 state after a short idle in default.
Enlarge the idle period to 7.9us for improving the R/W performance.
Signed-off-by: Ben Chuang <benchuanggli@gmail.com>
Link: https://lore.kernel.org/r/20210415032637.5219-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Not all commands need to be retried in case of a timeout/failure. This is
the case for the eMMC sanitize command, for example, which is issued
through the ioctl interface. More precisely, in case of timeout, retrying
could make the user wait for a very long time as each retry loop could last
for a couple of minutes.
Therefore, let's not use retries for the eMMC sanitize command.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20210414212236.346813-3-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add command retries parameter to __mmc_switch(), let caller
pass retries according to the caller's condition.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20210414212236.346813-2-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull OPP (Operating Performance Points) framework updates for v5.13
from Viresh Kumar:
"This adds devm variants for OPP APIs and updates few of the users
as well (Yangtao Li and Dmitry Osipenko)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
memory: samsung: exynos5422-dmc: Convert to use resource-managed OPP API
drm/panfrost: Convert to use resource-managed OPP API
drm/lima: Convert to use resource-managed OPP API
mmc: sdhci-msm: Convert to use resource-managed OPP API
spi: spi-qcom-qspi: Convert to use resource-managed OPP API
spi: spi-geni-qcom: Convert to use resource-managed OPP API
serial: qcom_geni_serial: Convert to use resource-managed OPP API
opp: Change return type of devm_pm_opp_attach_genpd()
opp: Change return type of devm_pm_opp_register_set_opp_helper()
opp: Add devres wrapper for dev_pm_opp_of_add_table
opp: Add devres wrapper for dev_pm_opp_set_supported_hw
opp: Add devres wrapper for dev_pm_opp_set_regulators
opp: Add devres wrapper for dev_pm_opp_set_clkname
devm_ioremap_resource() has recorded error log, so it's
unnecessary to record log again.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Laibin Qiu <qiulaibin@huawei.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20210409023801.3326572-1-qiulaibin@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
devm_ioremap_resource() has recorded error log, so it's
unnecessary to record log again.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jia Yang <jiayang5@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210409015424.3277212-1-jiayang5@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
devm_ioremap_resource() has recorded error log, so it's
unnecessary to record log again.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Laibin Qiu <qiulaibin@huawei.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20210409023349.3325907-1-qiulaibin@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that we got the timeout handling in the driver correct, we can use
this capability to avoid polling via the MMC core.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210409094606.4317-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CMD8 is not supported with Command Queue Enabled. Add required callback
to clear CQE_EN and CQE_INTR fields in the host controller register
before sending CMD8. Add corresponding callback in the CQHCI resume path
to re-enable CQE_EN and CQE_INTR fields.
Reported-by: Kamal Mostafa <kamal@canonical.com>
Tested-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Aniruddha Tvs Rao <anrao@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210407094617.770495-1-jonathanh@nvidia.com
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For GL9763E, although there is the best performance at the maximum delay.
Change the value to 20us in order to have better power consumption.
This change may reduce the maximum performance by 10%.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20210407093816.8863-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes the following W=1 kernel build warning(s):
drivers/mmc/host/moxart-mmc.c:257:7: warning: variable ‘dma_time’ set
but not used
drivers/mmc/host/moxart-mmc.c:395:7: warning: variable ‘pio_time’ set
but not used
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1617357231-93064-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the density increases, the 4-minute timeout value for sanitize is no
longer feasible. At the same time, devices of different densities have
different timeout values, which makes it difficult to use a common timeout
value. Therefore, let's pass down the userland-specified sanitize timeout
value so it can be used.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20210402092432.25069-2-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bus power may control card power, but the full reset done by SDHCI at
initialization still may not reset the power, whereas a direct write to
SDHCI_POWER_CONTROL can. That might be needed to initialize correctly, if
the card was left powered on previously.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210331081752.23621-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As indicated by function esdhc_change_pinstate(), SDR50 and DDR50
require pins_100mhz, while SDR104 and HS400 require pins_200mhz. Some
system design may support SDR50 and DDR50 with 100mhz pin state only
(without 200mhz one). Currently the combined 100/200 MHz pinctrl state
check prevents such system from running SDR50 and DDR50. Separate the
check to support such system design.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20210326110214.28416-1-shawnguo@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the CQHCI_QUIRK_SHORT_TXFR_DESC_SZ quirk because the
latest chips have this fixed and earlier chips have other
CQE problems that prevent the feature from being enabled.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210325192834.42955-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As pointed out by Ulf, "both "mmc->parent" and mmc_dev(mmc) are being
used in the entire c-file". Convert all the mmc->parent usage in all
sdhci host driver to mmc_dev() for consistency.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20210324155013.1e5faa3c@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: c2c4da37837e ("mmc: sdhci-of-dwcmshc: add rockchip platform support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210323112956.1016884-1-weiyongjun1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This commit adds ACPI support in the sdhci-of-dwcmshc driver for
BlueField-3 SoC. It has changes to only use the clock hierarchy
for Deviec Tree since the clk is not supported by ACPI. Instead,
ACPI can define 'clock-frequency' which is parsed by existing
sdhci_get_property(). This clock value will be returned in function
dwcmshc_get_max_clock().
Signed-off-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Link: https://lore.kernel.org/r/1616453211-275165-1-git-send-email-limings@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After reset, we manually flagged retune in runtime resume, but missed it
in the workqueue. To fix that and avoid the problem in the future, let's
flag retune in the reset handler directly whenever a card is present.
Reported-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210316085717.7276-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Resetting the IP core will lose the bus width information and not all
code paths recover it. So, make sure the latest bus width gets restored
in the reset routine. For that, tmio_mmc_set_bus_width() is moved, but
not modified.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: reworded commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210316085717.7276-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This variant is present on a Lenovo IdeaPad Slim 1, which uses an AMD Dali/Athlon Silver 3050e.
The Windows AMD SD Host Controller driver also lists this as a valid device ID.
Adding this device ID makes the internal eMMC storage on the Lenovo accessible.
Consequently this makes Linux installable and usable on it as well.
Signed-off-by: James Young <james@pocketfluff.org>
Link: https://lore.kernel.org/r/20210318124025.3002861-1-james@pocketfluff.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All recent SDHI instances can be reset via the reset controller. If one
is found, use it instead of the open coded reset. This is to get a
future-proof sane reset state.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210317091622.31890-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
renesas_sdhi_reset used to mainly reset the SCC but is now doing more
and even more will be added. So, factor out SCC reset to have a clear
distinction when we want to reset either SCC or SDHI+SCC.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210317091622.31890-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will soon allow resetting the whole IP core via a reset controller.
For this case, DMA must be terminated before the actual reset. For the
other cases, it is probably better, too.
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210317091622.31890-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The retrieval of driver data can be a bit simplified by using
device_get_match_data(), so switch to it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210314230824.148969-2-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Daniel Beer
Neil Armstrong
Linus Torvalds
Avri Altman
Andy Shevchenko
Ulf Hansson
Shawn Lin
Krzysztof Kozlowski
Wolfram Sang
Ben Chuang
Bean Huo
Rafael J. Wysocki
Laibin Qiu
Jia Yang
Aniruddha Tvs Rao
Ben Chuang
Yang Li
Adrian Hunter
Hao Fang
Shawn Guo
Al Cooper
Jisheng Zhang
Wei Yongjun
Liming Sun
Takeshi Saito
James Young
Fabio Estevam