Граф коммитов

6 Коммитов

Автор SHA1 Сообщение Дата
Linus Walleij 38656820aa ARM: ux500: move SPI pin config to device tree
This moves the SPI pin control table out of the board file
and into the device tree. Move the specific setting for
SSP0 on the HREFprev60 into the prev60-specific DTS file.
The SPI2 configuration is not really connected to any device,
as it will conflict with GPIO218 which is used on all HREFs.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij a12f703c5a ARM: ux500: move MUSB pin config to device tree
This moves the MUSB pin control table out of the board file
and into the device tree. Tie the config to the on-chip MUSB
device rather than the ab8500-usb device which is off-chip.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij 70b41abc15 ARM: ux500: move MSP pin control to the device tree
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add nodes for MSP0 and MSP2 on the HREF and Snowball
so we can reference the pins properly.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij 1e66235330 ARM: ux500: move MMC/SD/SDIO pin control to the device tree
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add entries for SDI1 and SDI2 on the Snowball so that the
WLAN pins on SDI1 can be used further on, and the unused pins
on SDI2 can be put to sleep.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij 96fee13f0f ARM: ux500: move I2C pin control to the device tree
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Define possible states also for I2C4 even if it's not
used by any board file at this time.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij 3bfdebbaeb ARM: ux500: move UART pin control to the device tree
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree.

We create a new .dtsi-file to be shared between all the
MOP500-related boards, that include all HREF variants and
the Snowball board. Assign pin states for HREF and Snowball
boards alike.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00