In order to support device tree probing of IXP4xx NOR flash
chips, a certain big-endian or mixed-endian memory access
pattern need to be used.
I have opted to use the pattern set by previous plug-ins
to physmap for Gemini and Versatile, just override some
functions and reuse most of the physmap core code as it
is to minimize maintenance.
Parts of drivers/mtd/ixp4xx.c are copied into this file.
After we have IXP4xx converted fully to device tree, the
drivers/mtd/ixp4xx.c file will be deleted and this will
be the only access pattern to the IXP4xx flash.
I did not keep the quirk in the flash write function
after probe, where the old code for a while checks for
access to odd addresses, fails and assigns a "faster"
write function once it has convinced probe to only use
2-byte accesses. As we mandate that this device should
be using bank-width = <2> this should not be a problem
unless misconfigured.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Avoid printing the address of l440gx_map.virt every time l440gx init.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
pxa2xx-flash is the only user of ioremap_cached, which is an alias
for ioremap_cache anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Mark switch cases where we are expecting to fall through.
Fix the following warning (Building: assabet_defconfig arm):
drivers/mtd/maps/sa1100-flash.c: In function ‘sa1100_probe_subdev’:
drivers/mtd/maps/sa1100-flash.c:82:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
printk(KERN_WARNING "SA1100 flash: unknown base address "
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"0x%08lx, assuming CS0\n", phys);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/maps/sa1100-flash.c:85:2: note: here
case SA1100_CS0_PHYS:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under version 2 of the gnu general public licence
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081202.750147367@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 24 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.162703968@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit dccd2304cc ("ARM: 7430/1: sizes.h: move from asm-generic
to <linux/sizes.h>"), <asm/sizes.h> and <asm-generic/sizes.h> are just
wrappers of <linux/sizes.h>.
This commit replaces all <asm/sizes.h> and <asm-generic/sizes.h> to
prepare for the removal.
Link: http://lkml.kernel.org/r/1553267665-27228-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The blackfin architecture has been removed a while ago, so there is
no more need to declare uclinux_ram_map as a global structure.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
When the physmap_of_core.c code was merged into physmap-core.c the
ability to use MTD_PHYSMAP_OF with only MTD_RAM selected was lost.
Restore this by adding MTD_RAM to the dependencies of MTD_PHYSMAP.
Fixes: commit 642b1e8dbe ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Richard Weinberger <richard@nod.at>
When the gpio-addr-flash.c driver was merged with physmap-core.c the
code to store the current gpio_values was lost. This meant that once a
gpio was asserted it was never de-asserted. Fix this by storing the
current offset in gpio_values like the old driver used to.
Fixes: commit ba32ce95cb ("mtd: maps: Merge gpio-addr-flash.c into physmap-core.c")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Marking a local variable as __xipram causes a warning because of the
noinline attribute:
drivers/mtd/maps/physmap-gemini.c:89:11: error: '__noinline__' attribute only applies to functions [-Werror,-Wignored-attributes]
map_word __xipram ret;
^
include/linux/mtd/xip.h:34:18: note: expanded from macro '__xipram'
#define __xipram noinline __attribute__ ((__section__ (".xiptext")))
I can't see any reason for the anotation anyway, so just remove it here.
Fixes: 9d3b5086f6 ("mtd: physmap_of_gemini: Handle pin control")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
NAND core changes:
- kernel-doc miscellaneous fixes.
- Third batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (ams-delta, marvell, fsmc, denali, tegra, vf610):
* Stopping to pass mtd_info objects to internal functions
* Reorganizing code to avoid forward declarations
* Dropping useless test in nand_legacy_set_defaults()
* Moving nand_exec_op() to internal.h
* Adding nand_[de]select_target() helpers
* Passing the CS line to be selected in struct nand_operation
* Making ->select_chip() optional when ->exec_op() is implemented
* Deprecating the ->select_chip() hook
* Moving the ->exec_op() method to nand_controller_ops
* Moving ->setup_data_interface() to nand_controller_ops
* Deprecating the dummy_controller field
* Fixing JEDEC detection
* Providing a helper for polling GPIO R/B pin
Raw NAND chip drivers changes:
- Macronix:
* Flagging 1.8V AC chips with a broken GET_FEATURES(TIMINGS)
Raw NAND controllers drivers changes:
- Ams-delta:
* Fixing the error path
* SPDX tag added
* May be compiled with COMPILE_TEST=y
* Conversion to ->exec_op() interface
* Dropping .IOADDR_R/W use
* Use GPIO API for data I/O
- Denali:
* Removing denali_reset_banks()
* Removing ->dev_ready() hook
* Including <linux/bits.h> instead of <linux/bitops.h>
* Changes to comply with the above fixes/cleanup done in the core.
- FSMC:
* Adding an SPDX tag to replace the license text
* Making conversion from chip to fsmc consistent
* Fixing unchecked return value in fsmc_read_page_hwecc
* Changes to comply with the above fixes/cleanup done in the core.
- Marvell:
* Preventing timeouts on a loaded machine (fix)
* Changes to comply with the above fixes/cleanup done in the core.
- OMAP2:
* Pass the parent of pdev to dma_request_chan() (fix)
- R852:
* Use generic DMA API
- sh_flctl:
* Converting to SPDX identifiers
- Sunxi:
* Write pageprog related opcodes to the right register: WCMD_SET (fix)
- Tegra:
* Stop implementing ->select_chip()
- VF610:
* Adding an SPDX tag to replace the license text
* Changes to comply with the above fixes/cleanup done in the core.
- Various trivial/spelling/coding style fixes.
SPI-NAND drivers changes:
- Removing the depreacated mt29f_spinand driver from staging.
- Adding support for:
* Toshiba TC58CVG2S0H
* GigaDevice GD5FxGQ4xA
* Winbond W25N01GV
This enables the complex mapping for the Gemini and kicks in
custom read/write functions that will wrap the existing
simple functions in calls to enable/disable the parallel
flash pins using pin controls.
This is necessary on some hardware such as the D-Link
DIR-685 where all flash pins are patched in/out at the same
time, but some of the flash pins are in practice unused by
the flash and have anyway been reused as GPIO.
This concerns specifically CE1 on the Gemini. There is only
one flash chip, so only CE0 is used, and the line for CE1
has been reused as chip select for the emulated SPI port
connected to the display. If we try to use the same lines
for flash and GPIO at the same time, one of them will loose:
the GPIO line will disappear because it gets disconnected
from the pin when the flash group is muxed out.
Fix this by introducing two pin control states named simply
"enabled" and "disabled" and only enable the flash lines
when absolutely necessary (during read/write/copy). This
way, they are available for GPIO at all other times and
the display works.
Collect all the state variables in a struct named
struct gemini_flash and allocate this struct at probe
time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
SoC-specific drivers might provide their own map->xxx()
implementations, and calling simple_map_init() unconditionally will
override those implementations.
Make sure map->read is NULL before calling simple_map_init().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
SUBDIRS has been kept as a backward compatibility since
commit ("[PATCH] kbuild: external module support") in 2002.
We do not need multiple ways to do the same thing, so I will remove
SUBDIRS after the Linux 5.3 release. I cleaned up in-tree code, and
updated the document so that nobody would try to use it.
Meanwhile, display the following warning if SUBDIRS is used.
Makefile:189: ================= WARNING ================
Makefile:190: 'SUBDIRS' will be removed after Linux 5.3
Makefile:191: Please use 'M=' or 'KBUILD_EXTMOD' instead
Makefile:192: ==========================================
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com> # for scx200_docflash.c
Acked-by: Guenter Roeck <linux@roeck-us.net> # for scx200_wdt.c
Looks like this driver was initially added to support the NOR on the
DA830-EVM (Davinci) board, but the board file update was never merged.
Keeping unused drivers just adds to the maintenance burden, so let's
remove it if nobody uses it.
Cc: David Griego <dgriego@mvista.com>
Cc: Aleksey Makarov <amakarov@ru.mvista.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Savinay Dharmappa <savinay.dharmappa@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
It is preferred to have the positive statement on an if/else. While we
are at it we replace the way we access rom_probe_types.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Enabling -Wvla found another variable-length array with randconfig
testing:
drivers/mtd/maps/sa1100-flash.c: In function 'sa1100_setup_mtd':
drivers/mtd/maps/sa1100-flash.c:224:10: error: ISO C90 forbids variable length array 'cdev' [-Werror=vla]
Dynamically allocate the cdev array passed to mtd_concat_create()
instead of using a VLA.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Olof Johansson <olof@lixom.net>
Controlling some MSB address lines using GPIOs is just a small
deviation from the generic physmap logic, and merging those two drivers
allows us to share most of the probe logic, which is a good thing.
Also, the gpio-addr-flash driver is unused since the removal of
the blackfin arch in v4.17, so we can safely remove the old driver
without risking breaking existing boards.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Now that the physmap_of driver is gone, the gemini and versative
extensions are part of the physmap driver. Rename the source files and
the config option to reflect this.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
There's no real reason to have two separate driver for the DT and pdata
case. Just do what we do everywhere else and handle DT and pdata
parsing in the same driver.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
We want to merge the physmap and physmap_of driver, but before we can
do that we must prepare things to create physmap.o out of several .c
files. Rename physmap.c into physmap-core.c and add a new Makefile
rule to create physmap.o (right now it only contains physmap-core.o).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
There's no point going to the err_out path since no resources have
been allocated yet, just return -ENOMEM directly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
mtd_device_parse_register() and mtd_device_unregister() can fail,
check their return code and propagate the error to the upper layer
if needed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Remove the MAX_RESOURCES limitation by dynamically allocating the
->mtds[] and ->maps[] at probe time based on the number of iomem
resources attached to the platform device.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Replace printk(KERN_NOTICE) by dev_notice() use the %pR specifier to
print the iomem resource.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Stop manipulating the dev->resource array directly and use the
platform_get_resource() helper instead.
While at it, fix the loop check so that we never overflow the info->maps
and info->mtds array even if the number of resources attached to the
platform dev is higher than MAX_RESOURCES.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The ->map and ->mtd fields are actually arrays of map and mtd objects.
Rename those fields into ->maps and ->mtds to make it obvious.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Convert from legacy gpio API to gpiod.
Board files will have to use gpiod_lookup_tables.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
By replacing the array with an integer we can avoid completely
the bit comparison loop if the value has not changed (by far
the most common case).
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
By using the order of the window instead of the size, we can replace a
lot of expensive division and modulus on the code with simple bit
operations.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
By using devm functions we can make the code cleaner.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
We should only iomap the area of the chip that is memory mapped.
Otherwise we could be mapping devices beyond the memory space or that
belong to other devices.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Fixes: ebd71e3a48 ("mtd: maps: gpio-addr-flash: fix warnings and make more portable")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
During probe, if there was an error the memory region and the memory
map were not properly released.This can lead a system unusable if
deferred probe is in use.
Replace mem_request and map with devm_ioremap_resource
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This struct does not seem to be used anywhere on the code
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Fix 2 printk format warnings (this driver is currently only used by
arch/sh/) by using "%pap" instead of "%lx".
Fixes these build warnings:
../drivers/mtd/maps/solutionengine.c: In function 'init_soleng_maps':
../include/linux/kern_levels.h:5:18: warning: format '%lx' expects argument of type 'long unsigned int', but argument 2 has type 'resource_size_t' {aka 'unsigned int'} [-Wformat=]
../drivers/mtd/maps/solutionengine.c:62:54: note: format string is defined here
printk(KERN_NOTICE "Solution Engine: Flash at 0x%08lx, EPROM at 0x%08lx\n",
~~~~^
%08x
../include/linux/kern_levels.h:5:18: warning: format '%lx' expects argument of type 'long unsigned int', but argument 3 has type 'resource_size_t' {aka 'unsigned int'} [-Wformat=]
../drivers/mtd/maps/solutionengine.c:62:72: note: format string is defined here
printk(KERN_NOTICE "Solution Engine: Flash at 0x%08lx, EPROM at 0x%08lx\n",
~~~~^
%08x
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: linux-mtd@lists.infradead.org
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: linux-sh@vger.kernel.org
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Fix indentation and replace '---help---' by 'help' to make things
consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
If driver doesn't specify parsers it can use that little helper.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
When ioremap_nocache fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling ioremap_nocache.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Linus Walleij
Fuqian Huang
Wolfram Sang
Christoph Hellwig
Gustavo A. R. Silva
Thomas Gleixner
Masahiro Yamada
Thomas Huth
Chris Packham
Arnd Bergmann
Linus Torvalds
Boris Brezillon
Ricardo Ribalda Delgado
Randy Dunlap
Rafał Miłecki
Zhouyang Jia
Kees Cook