The original ID that was added for Comet Lake PCH was
actually for the -LP (low power) variant even though the
constant for it said CMLH. Changing that while at it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191212093713.60614-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear ep0's DWC3_EP_TRANSFER_STARTED flag if the END_TRANSFER command is
completed. Otherwise, we can't start control transfer again after
END_TRANSFER.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Normally the END_TRANSFER command completion handler will clear the
DWC3_EP_TRANSFER_STARTED flag. However, if the command was sent without
interrupt on completion, then the flag will not be cleared. Make sure to
clear the flag in this case.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the condition to kick the transfer without
giving back the requests when either request has remaining data
or when there are pending SGs. The && check was introduced during
spliting up the dwc3_gadget_ep_cleanup_completed_requests() function.
Fixes: f38e35dd84 ("usb: dwc3: gadget: split dwc3_gadget_ep_cleanup_completed_requests()")
Cc: stable@vger.kernel.org
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191121132914.29368-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have TI's glue layer for the Cadence USB3 controller going
upstream. Tegra's XUDC driver is also going upstream with this pull
request.
Apart from these two big features, we have a bunch of patches switching
over to devm_platform_ioremap_resource() in order to simplify code a
little; and a non-critical fix for DWC3 usage via kexec.
-----BEGIN PGP SIGNATURE-----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=Xyc8
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.5
We have TI's glue layer for the Cadence USB3 controller going
upstream. Tegra's XUDC driver is also going upstream with this pull
request.
Apart from these two big features, we have a bunch of patches switching
over to devm_platform_ioremap_resource() in order to simplify code a
little; and a non-critical fix for DWC3 usage via kexec.
* tag 'usb-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (44 commits)
usb: dwc3: of-simple: add a shutdown
usb: cdns3: Add TI specific wrapper driver
dt-bindings: usb: Add binding for the TI wrapper for Cadence USB3 controller
usb: mtu3: fix race condition about delayed_status
usb: gadget: Add UDC driver for tegra XUSB device mode controller
usb: dwc3: debug: Remove newline printout
usb: dwc2: use a longer core rest timeout in dwc2_core_reset()
usb: gadget: udc: lpc32xx: Use devm_platform_ioremap_resource() in lpc32xx_udc_probe()
USB: gadget: udc: clean up an indentation issue
usb: gadget: Quieten gadget config message
phy: renesas: rcar-gen3-usb2: Use platform_get_irq_optional() for optional irq
usb: gadget: Remove set but not used variable 'opts' in msg_do_config
usb: gadget: Remove set but not used variable 'opts' in acm_ms_do_config
usb: mtu3: add a new function to do status stage
usb: gadget: configfs: fix concurrent issue between composite APIs
usb: gadget: f_tcm: Provide support to get alternate setting in tcm function
usb: gadget: Correct NULL pointer checking in fsl gadget
usb: fsl: Remove unused variable
USB: dummy-hcd: use usb_urb_dir_in instead of usb_pipein
USB: dummy-hcd: increase max number of devices to 32
...
Now the USB gadget subsystem can use the USB debugfs root directory,
so move dwc3's directory from the root of the debugfs filesystem into
the root of usb
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1573541519-28488-4-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When disabling an endpoint which has cancelled requests, we should
make sure to giveback requests that are currently pending in the
cancelled list, otherwise we may fall into a situation where command
completion interrupt fires after endpoint has been disabled, therefore
causing a splat.
Fixes: fec9095bde "usb: dwc3: gadget: remove wait_end_transfer"
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191031090713.1452818-1-felipe.balbi@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case we're loading a new kernel via kexec, let's make sure to
cleanup the dwc3 address space correctly. This means that we should
run the same steps from driver remove, so just extract a reusable
function for both cases.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
layerscape board sometimes reported some usb call trace, that is due to
kernel sent LPM tokerns automatically when it has no pending transfers
and think that the link is idle enough to enter L1, which procedure will
ask usb register has a recovery,then kernel will compare USBx_GFLADJ and
set GFLADJ_30MHZ, GFLADJ_30MHZ_REG until GFLADJ_30MHZ is equal 0x20, if
the conditions were met then issue occur, but whatever the conditions
whether were met that usb is all need keep GFLADJ_30MHZ of value is 0x20
(xhci spec ask use GFLADJ_30MHZ to adjust any offset from clock source
that generates the clock that drives the SOF counter, 0x20 is default
value of it)That is normal logic, so need remove the call trace.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In dwc3_pci_probe a call to platform_device_alloc allocates a device
which is correctly put in case of error except one case: when the call to
platform_device_add_properties fails it directly returns instead of
going to error handling. This commit replaces return with the goto.
Fixes: 1a7b12f69a ("usb: dwc3: pci: Supply device properties via driver data")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After many randconfig builds, one configuration caused a link
error with dwc3-meson-g12a lacking the regmap-mmio code:
drivers/usb/dwc3/dwc3-meson-g12a.o: In function `dwc3_meson_g12a_probe':
dwc3-meson-g12a.c:(.text+0x9f): undefined reference to `__devm_regmap_init_mmio_clk'
Add the select statement that we have for all other users
of that dependency.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The newline from the unknown link state tracepoint doesn't follow the
other tracepoints, and it looks unsightly. Let's remove it.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For DRD controllers, the programming guide recommended that
GUSB3PIPECTL.SUSPENDABLE and GUSB2PHYCFG.SUSPHY to be cleared after
power-on reset and only set after the controller initialization is
completed. This can be done after device soft-reset in dwc3_core_init().
This patch makes sure to clear GUSB3PIPECTL.SUSPENDABLE and
GUSB2PHYCFG.SUSPHY before core initialization and only set them after
the device soft-reset is completed.
Reference: DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section
1.2.49 and 1.2.45
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since commit 7723f4c5ec ("driver core: platform: Add an error message to
platform_get_irq*()"), platform_get_irq() will call dev_err() itself on
failure, so there is no need for the driver to also do this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191005210449.3926-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3 code to get the "peripheral" / "host" / "otg" IRQ first tries
platform_get_irq_byname() and then falls back to the IRQ at index 0 if
the platform_get_irq_byname().
In this case we do not want platform_get_irq_byname() to print an error
on failure, so switch to platform_get_irq_byname_optional() instead which
does not print an error.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205037
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191005210449.3926-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190923154956.6868-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calls to USB2 generic PHY calibrate() method has been moved to HCD core,
which now successfully handles generic PHYs and their calibration after
every HCD reset. This fixes all the timing issues related to PHY
calibration done directly from DWC3 driver: incorrect operation after
system suspend/resume or USB3.0 detection failure when XHCI-plat driver
compiled as separate module.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Jochen Sprickerhof <jochen@sprickerhof.de>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20190829053028.32438-3-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With only 45 non-merge commits, we have a small merge window from the
Gadget perspective.
The biggest change here is the addition of the Cadence USB3 DRD
Driver. All other changes are small, non-critical fixes or smaller new
features like the improvement to BESL handling in dwc3.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=KUJN
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: Changes for v5.4 merge window
With only 45 non-merge commits, we have a small merge window from the
Gadget perspective.
The biggest change here is the addition of the Cadence USB3 DRD
Driver. All other changes are small, non-critical fixes or smaller new
features like the improvement to BESL handling in dwc3.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* tag 'usb-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (45 commits)
usb: gadget: net2280: Add workaround for AB chip Errata 11
usb: gadget: net2280: Move all "ll" registers in one structure
usb: dwc3: gadget: Workaround Mirosoft's BESL check
usb:cdns3 Fix for stuck packets in on-chip OUT buffer.
usb: cdns3: Add Cadence USB3 DRD Driver
usb: common: Simplify usb_decode_get_set_descriptor function.
usb: common: Patch simplify usb_decode_set_clear_feature function.
usb: common: Separated decoding functions from dwc3 driver.
dt-bindings: add binding for USBSS-DRD controller.
usb: gadget: composite: Set recommended BESL values
usb: dwc3: gadget: Set BESL config parameter
usb: dwc3: Separate field holding multiple properties
usb: gadget: Export recommended BESL values
usb: phy: phy-fsl-usb: Make structure fsl_otg_initdata constant
usb: udc: lpc32xx: silence fall-through warning
usb: dwc3: meson-g12a: fix suspend resume regulator unbalanced disables
usb: udc: lpc32xx: remove set but not used 3 variables
usb: gadget: udc: core: Fix segfault if udc_bind_to_driver() for pending driver fails
usb: dwc3: st: Add of_dev_put() in probe function
usb: dwc3: st: Add of_node_put() before return in probe function
...
While testing our host system using Microsoft's usb stack against our
gadget for various BESL values, we found an issue with their usb stack
when the recommended baseline BESL value is 0 (125us) or when the deep
BESL is 1 or less. The Windows host will issue a usb reset immediately
after it receives the extended BOS descriptor and the enumeration will
fail after a few attempts.
To keep compatibility with Microsoft's host usb stack, let's workaround
this issue by using the recommended baseline BESL of 1 (or 150us)
and clamp the deep BESL value within 2 to 15.
This was tested against Windows 10 build 18956.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Patch moves some decoding functions from driver/usb/dwc3/debug.h driver
to driver/usb/common/debug.c file. These moved functions include:
dwc3_decode_get_status
dwc3_decode_set_clear_feature
dwc3_decode_set_address
dwc3_decode_get_set_descriptor
dwc3_decode_get_configuration
dwc3_decode_set_configuration
dwc3_decode_get_intf
dwc3_decode_set_intf
dwc3_decode_synch_frame
dwc3_decode_set_sel
dwc3_decode_set_isoch_delay
dwc3_decode_ctrl
These functions are used also in inroduced cdns3 driver.
All functions prefixes were changed from dwc3 to usb.
Also, function's parameters has been extended according to the name
of fields in standard SETUP packet.
Additionally, patch adds usb_decode_ctrl function to
include/linux/usb/ch9.h file.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When operating with LPM signals, the controller asserts the deep
low-power signal (utmi_l1_suspend_n) to the phy when the BESL value of
the LPM token is equal to or greater than DCTL.HIRD_Thres[3:0] (and
with DCTL.HIRD_Thres[4] set). Otherwise, the shallow low-power signal
(utmi_sleep_n) is asserted. Set the recommended deep BESL equal to the
controller's DCTL.HIRD_Thres[3:0] setting, and set the baseline BESL
to 0 for the shallow low-power signal. This maximizes the opportunity
for L1 residency and optimizes power savings.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc->hird_threshold field should store "snps,hird_threshold" property
only and not a combination of multiple properties. Remove the value of
"snps,is-utmi-l1-suspend" property from the field dwc->hird_threshold.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When going in suspend, in Device mode, then resuming back leads
to the following:
unbalanced disables for USB_PWR_EN
WARNING: CPU: 0 PID: 163 at ../drivers/regulator/core.c:2590 _regulator_disable+0x104/0x180
Hardware name: Amlogic Meson G12A U200 Development Board (DT)
[...]
pc : _regulator_disable+0x104/0x180
lr : _regulator_disable+0x104/0x180
[...]
Call trace:
_regulator_disable+0x104/0x180
regulator_disable+0x40/0x78
dwc3_meson_g12a_otg_mode_set+0x84/0xb0
dwc3_meson_g12a_irq_thread+0x58/0xb8
irq_thread_fn+0x28/0x80
irq_thread+0x118/0x1b8
kthread+0xf4/0x120
ret_from_fork+0x10/0x18
This disables the regulator if enabled on suspend, and the reverse on
resume.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reported-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In function st_dwc3_probe, variable child_pdev takes the value returned
by of_find_device_by_node, which gets a device pointer but does not put
it. If child_pdev is not put before the probe function returns, it may
cause a reference leak. Hence put child_pdev after its last usage.
Issue found with Coccinelle.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The local variable child in the function st_dwc3_probe takes the return
value of of_get_child_by_name, which gets a node and does not put it. If
the function returns without releasing child, this could cause a memory
error. Hence put child as soon as there is no more use for it. Also
create a new label, err_node_put, just before label undo_softreset; so
that err_node_put puts child. In between initialisation of child and its
first put, modify all statements that go to undo_softreset to now go to
err_node_put instead, from where they can fall through to
undo_softreset.
Issue found with Coccinelle.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts
commit 6a4290cc28 ("usb: dwc3: gadget: set the OTG flag in dwc3 gadget driver.")
We don't yet support any of the OTG mechanisms (HNP/SRP/ADP)
and are not setting gadget->otg_caps, so don't set gadget->is_otg
flag.
If we do then we end up publishing a OTG1.0 descriptor in
the gadget descriptor which causes device enumeration to fail
if we are connected to a host with CONFIG_USB_OTG enabled.
Host side log without this patch
[ 96.720453] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 96.901391] usb 1-1: Dual-Role OTG device on non-HNP port
[ 96.907552] usb 1-1: set a_alt_hnp_support failed: -32
[ 97.060447] usb 1-1: new high-speed USB device number 3 using xhci-hcd
[ 97.241378] usb 1-1: Dual-Role OTG device on non-HNP port
[ 97.247536] usb 1-1: set a_alt_hnp_support failed: -32
[ 97.253606] usb usb1-port1: attempt power cycle
[ 97.960449] usb 1-1: new high-speed USB device number 4 using xhci-hcd
[ 98.141383] usb 1-1: Dual-Role OTG device on non-HNP port
[ 98.147540] usb 1-1: set a_alt_hnp_support failed: -32
[ 98.300453] usb 1-1: new high-speed USB device number 5 using xhci-hcd
[ 98.481391] usb 1-1: Dual-Role OTG device on non-HNP port
[ 98.487545] usb 1-1: set a_alt_hnp_support failed: -32
[ 98.493532] usb usb1-port1: unable to enumerate USB device
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use clk_bulk_prepare_enable() and clk_bulk_disable_unprepare() to
simplify code a bit. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devres to get clocks and drop explicit clock freeing. No
functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 08f871a3ac ("usb: dwc3: host: convey the PHYs to xhci") added
forwarding of the generic PHYs from DWC3 core to the instantiated XHCI-plat
device. However XHCI(-plat) driver never gained support for generic PHYs,
thus the lookup added by that commit is never used. In meantime the commit
d64ff406e5 ("usb: dwc3: use bus->sysdev for DMA configuration")
incorrectly changed the device used for creating lookup, making the lookup
useless and generic PHYs inaccessible from XHCI device.
However since commit 178a0bce05 ("usb: core: hcd: integrate the PHY
wrapper into the HCD core") USB HCD already handles generic PHYs acquired
from the HCD's 'sysdev', which in this case is DWC3 core device. This means
that creating any custom lookup entries for XHCI driver is no longer needed
and can be simply removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Starting from DWC_usb31 version 1.90a and later, the DCTL.CSFRST bit
will not be cleared until after all the internal clocks are synchronized
during soft-reset. This may take a little more than 50ms. Set the
polling rate at 20ms instead.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This enum is only used in drivers/usb/dwc3/dwc3-omap3.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use use device_property_count_u32() directly, that makes code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20190802130408.20336-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-47-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch moves some decoding functions from driver/usb/dwc3/debug.h driver
to driver/usb/gadget/debug.c file. These moved functions include:
dwc3_decode_get_status
dwc3_decode_set_clear_feature
dwc3_decode_set_address
dwc3_decode_get_set_descriptor
dwc3_decode_get_configuration
dwc3_decode_set_configuration
dwc3_decode_get_intf
dwc3_decode_set_intf
dwc3_decode_synch_frame
dwc3_decode_set_sel
dwc3_decode_set_isoch_delay
dwc3_decode_ctrl
These functions are used also in inroduced cdns3 driver.
All functions prefixes were changed from dwc3 to usb.
Also, function's parameters has been extended according to the name
of fields in standard SETUP packet.
Additionally, patch adds usb_decode_ctrl function to
include/linux/usb/gadget.h file.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The member @lock of dwc3_ep struct is only initialized,
and not used elsewhere, so remove it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget applications may have a requirement to disable the U1 and U2
entry based on the usecase. Below are few usecases where the disabling
U1/U2 entries may be possible.
Usecase 1:
When combining dwc3 with an redriver for a USB Type-C device solution, it
sometimes have problems with leaving U1/U2 for certain hosts, resulting in
link training errors and reconnects. For this U1/U2 state entries may be
avoided.
Usecase 2:
When performing performance benchmarking on mass storage gadget the
U1 and U2 entries can be disabled.
Usecase 3:
When periodic transfers like ISOC transfers are used with bInterval
of 1 which doesn't require the link to enter into U1 or U2 state entry
(since ping is issued from host for every uframe interval). In this
case the U1 and U2 entry can be disabled.
Disablement of U1/U2 can be done by setting U1DevExitLat and U2DevExitLat
values to 0 in the BOS descriptor. Host on seeing 0 value for U1DevExitLat
and U2DevExitLat, it doesn't send SET_SEL requests to the gadget. There
may be some hosts which may send SET_SEL requests even after seeing 0 in
the UxDevExitLat of BOS descriptor. To aviod U1/U2 entries for these type
of hosts, dwc3 controller can be programmed to reject those U1/U2 requests
by not enabling ACCEPTUxENA bits in DCTL register.
This patch updates the same.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Claus H. Stovgaard <cst@phaseone.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use of_clk_get_parent_count() instead of open coding.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The required clocks needs to be enabled before the first register
access. After commit fe8abf332b ("usb: dwc3: support clocks and resets
for DWC3 core"), this happens when the dwc3_core_is_valid function is
called, but the mentioned commit adds that call in the wrong place,
before the clocks are enabled. So, move that call after the
clk_bulk_enable() to ensure the clocks are enabled and the reset
deasserted.
I detected this while, as experiment, I tried to move the clocks and resets
from the glue layer to the DWC3 core on a Samsung Chromebook Plus.
That was not detected before because, in most cases, the glue layer
initializes SoC-specific things and then populates the child "snps,dwc3"
with those clocks already enabled.
Fixes: b873e2d0ea ("usb: dwc3: Do core validation early on probe")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_qcom_clk_init() is called with of_count_phandle_with_args() as an
argument. If of_count_phandle_with_args() returns an error, the number
of clocks will be a negative value and will lead to undefined behaviour.
Ensure we check for an error before attempting to blindly use the value.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Heikki Krogerus
Thinh Nguyen
Tejas Joglekar
Krzysztof Kozlowski
Greg Kroah-Hartman
Chunfeng Yun
Felipe Balbi
Yinbo Zhu
Navid Emamdoost
Arnd Bergmann
Hans de Goede
Marek Szyprowski
Pawel Laszczak
Neil Armstrong
Nishka Dasgupta
Roger Quadros
Andrey Smirnov
Masahiro Yamada
Andy Shevchenko
YueHaibing
Stephen Boyd
Anurag Kumar Vulisha
Kefeng Wang
Enric Balletbo i Serra
Lee Jones