Граф коммитов

199 Коммитов

Автор SHA1 Сообщение Дата
Matt Gates 3ce438df10 [SCSI] hpsa: allow SCSI mid layer to handle unit attention
We were clobbering the SCSI status and setting
cmd->result = DID_SOFT_ERROR << 16; to get a retry,
but better to let the mid layer handle the unit
attention.

Signed-off-by: Matt Gates <matthew.gates@hp.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-12-19 20:56:30 -08:00
Stephen M. Cameron 0ddf1d7750 [SCSI] hpsa: do not require board "not ready" status after hard reset
Immediately following a hard board reset, There are some
mandatory delays during which we must not access the board
and during which we might miss the "not ready" status,
therefore it is a mistake to look for and expect to see
the "not ready" status.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-12-19 20:56:30 -08:00
Stephen M. Cameron 28e1344647 [SCSI] hpsa: enable unit attention reporting
This used to be the default, but at some point the firmware guys
changed the default and I failed to notice.  Now to get unit
attention notifications, you must twiddle a bit indicating you
want them.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-12-19 20:56:30 -08:00
Stephen M. Cameron 97a5e98c1b [SCSI] hpsa: rename scsi prefetch field
The field contains more bits than just the one
to indicate whether scsi prefetch should be turned on.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-12-19 20:56:29 -08:00
Stephen M. Cameron 8a98db7386 [SCSI] hpsa: use workqueue instead of kernel thread for lockup detection
Much simpler and avoids races starting/stopping the thread.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-12-19 20:56:29 -08:00
Mike Miller d5747e0aa0 [SCSI] hpsa: remove P822se PCI ID
Remove PCI ID for the never shipped P822se.

Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-12-19 07:39:04 -08:00
Stephen M. Cameron 396883e292 [SCSI] hpsa: prevent stalled i/o
If a fifo full condition is encountered, i/o requests will stack
up in the h->reqQ queue.  The only thing which empties this queue
is start_io, which only gets called when new i/o requests come in.
If none are forthcoming, i/o in h->reqQ will be stalled.

To fix this, whenever fifo full condition is encountered, this
is recorded, and the interrupt handler examines this to see
if a fifo full condition was recently encountered when a
command completes and will call start_io to prevent i/o's in
h->reqQ from getting stuck.

I've only ever seen this problem occur when running specialized
test programs that pound on the the CCISS_PASSTHRU ioctl.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-12-19 07:38:56 -08:00
Stephen M. Cameron 0390f0c0df [SCSI] hpsa: cap CCISS_PASSTHRU at 20 concurrent commands.
Cap CCISS_BIG_PASSTHRU as well.  If an attempt is made
to exceed this, ioctl() will return -1 with errno == EAGAIN.

This is to prevent a userland program from exhausting all of
pci_alloc_consistent memory.  I've only seen this problem when
running a special test program designed to provoke it.  20
concurrent commands via the passthru ioctls (not counting SG_IO)
should be more than enough.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-12-19 07:38:56 -08:00
Stephen M. Cameron e06c8e5c34 [SCSI] hpsa: add MSA 2040 to list of external target devices
Signed-off-by: Scott Teel <scott.teel@hp.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-12-16 10:57:53 -08:00
Stephen M. Cameron e2d4a1f6b4 [SCSI] hpsa: fix memory leak in CCISS_BIG_PASSTHRU ioctl
We were leaking a command buffer if a DMA mapping error was
encountered in the CCISS_BIG_PASSTHRU ioctl.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-12-16 10:57:53 -08:00
Stephen M. Cameron a4af4606db [SCSI] hpsa: remove unneeded include of seq_file.h
Signed-off-by: Scott Teel <scott.teel@hp.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-12-16 10:57:52 -08:00
Stephen M. Cameron 8500923947 [SCSI] hpsa: add 5 second delay after doorbell reset
The hardware guys tell us that after initiating a software
reset via the doorbell register we need to wait 5 seconds before
attempting to talk to the board *at all*.  This means that we
cannot watch the board to verify it transitions from "ready" to
to "not ready" then back "ready", since this transition will
most likely happen during those 5 seconds (though we can still
verify the reset happens by watching the "driver version" field
get cleared.)

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-12-16 10:57:52 -08:00
Stephen M. Cameron 702890e3b9 [SCSI] hpsa: do not attempt to flush the cache on locked up controllers
There's no point in trying since it can't work, and if you do
try, it will just hang the system on shutdown.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-12-16 10:57:52 -08:00
Stephen M. Cameron 88bf6d62db [SCSI] hpsa: return 0 from driver probe function on success, not 1
A return value of 1 is interpreted as an error.  See pci_driver.
in local_pci_probe().  If you're wondering how this ever could
have worked, it's because it used to be the case that only return
values less than zero were interpreted as failure.  But even in
the current kernel if the driver registers its various entry
points with the kernel, and then returns a value which is
interpreted as failure, those registrations aren't undone, so
the driver still mostly works.  However, the driver's remove
function wouldn't be called on rmmod, and pci power management
functions wouldn't work.  In the case of Smart Array, since it
has a battery backed cache (or else no cache) even if the driver
is not shut down properly as long as there is no outstanding
i/o, nothing too bad happens, which is why it took so long to
notice.

Requesting backport to stable because the change to pci-driver.c
which requires driver probe functions to return 0 occurred between
2.6.35 and 2.6.36 (the pci power management breakage) and again
between 3.7 and 3.8 (pci_dev->driver getting set to NULL in
local_pci_probe() preventing driver remove function from being
called on rmmod.)

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-11-30 19:28:00 -05:00
Stephen M. Cameron 2e311fbabd [SCSI] hpsa: do not discard scsi status on aborted commands
We inadvertantly discarded the scsi status for aborted commands.
For some commands (e.g. reads from tape drives) these can't be retried,
and if we discarded the scsi status, the scsi mid layer couldn't notice
anything was wrong and the error was not reported.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-11-30 17:04:49 -05:00
Martin K. Petersen 54b2b50c20 [SCSI] Disable WRITE SAME for RAID and virtual host adapter drivers
Some host adapters do not pass commands through to the target disk
directly. Instead they provide an emulated target which may or may not
accurately report its capabilities. In some cases the physical device
characteristics are reported even when the host adapter is processing
commands on the device's behalf. This can lead to adapter firmware hangs
or excessive I/O errors.

This patch disables WRITE SAME for devices connected to host adapters
that provide an emulated target. Driver writers can disable WRITE SAME
by setting the no_write_same flag in the host adapter template.

[jejb: fix up rejections due to eh_deadline patch]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-11-29 08:48:39 +04:00
Linus Torvalds 9073e1a804 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
 "Usual earth-shaking, news-breaking, rocket science pile from
  trivial.git"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
  doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
  doc: add missing files to timers/00-INDEX
  timekeeping: Fix some trivial typos in comments
  mm: Fix some trivial typos in comments
  irq: Fix some trivial typos in comments
  NUMA: fix typos in Kconfig help text
  mm: update 00-INDEX
  doc: Documentation/DMA-attributes.txt fix typo
  DRM: comment: `halve' -> `half'
  Docs: Kconfig: `devlopers' -> `developers'
  doc: typo on word accounting in kprobes.c in mutliple architectures
  treewide: fix "usefull" typo
  treewide: fix "distingush" typo
  mm/Kconfig: Grammar s/an/a/
  kexec: Typo s/the/then/
  Documentation/kvm: Update cpuid documentation for steal time and pv eoi
  treewide: Fix common typo in "identify"
  __page_to_pfn: Fix typo in comment
  Correct some typos for word frequency
  clk: fixed-factor: Fix a trivial typo
  ...
2013-11-15 16:47:22 -08:00
Mike Miller f79666bbb4 [SCSI] hpsa: remove unused Smart Array ID
This patch removes the PCI ID of a cancelled Smart Array.

Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-10-25 09:57:55 +01:00
Jingoo Han 08b7e10716 SCSI: remove unnecessary pci_set_drvdata()
Since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound),
the driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-10-14 15:26:04 +02:00
Linus Torvalds 0375ec5899 SCSI misc on 20130915
This patch set is a set of driver updates (megaraid_sas, fnic, lpfc, ufs,
 hpsa) we also have a couple of bug fixes (sd out of bounds and ibmvfc error
 handling) and the first round of esas2r checker fixes and finally the much
 anticipated big endian additions for megaraid_sas.
 
 Signed-off-by: James Bottomley <JBottomley@Parallels.com>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iQEcBAABAgAGBQJSNheiAAoJEDeqqVYsXL0MueMIAKD1kaB0oooRawE1+0vpKmyV
 eE2M6trA8ofTeq0z1eNfRsVMkRsUuG9exW0CKS2z6mHiWwQ/zGbqT7ukveW+dMi3
 mjKD0yO5ODk6bohWX/LiwZ6NGZSwC0dbIacXNy5ZsXKEizqwo1Jcc7qC/0AWn+o7
 WpIL48XLPH0HqjQZ3dvgC6TWeFZOn9cKOWvQQq0S3ENALOx/eLZ+C7VrJLx5Magv
 myNOUkTLzdlYglQfjaNO6et98k2oHTrzKwH7U2X6U75q7L8Pkj4RbNzce/Ge301V
 u+R1w+BlbeTPdHopTBoTJupsvqDYBZxVwS7rr8nhSvfKduQppHnN6jX8yR4XNeM=
 =RG3j
 -----END PGP SIGNATURE-----

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull misc SCSI driver updates from James Bottomley:
 "This patch set is a set of driver updates (megaraid_sas, fnic, lpfc,
  ufs, hpsa) we also have a couple of bug fixes (sd out of bounds and
  ibmvfc error handling) and the first round of esas2r checker fixes and
  finally the much anticipated big endian additions for megaraid_sas"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (47 commits)
  [SCSI] fnic: fnic Driver Tuneables Exposed through CLI
  [SCSI] fnic: Kernel panic while running sh/nosh with max lun cfg
  [SCSI] fnic: Hitting BUG_ON(io_req->abts_done) in fnic_rport_exch_reset
  [SCSI] fnic: Remove QUEUE_FULL handling code
  [SCSI] fnic: On system with >1.1TB RAM, VIC fails multipath after boot up
  [SCSI] fnic: FC stat param seconds_since_last_reset not getting updated
  [SCSI] sd: Fix potential out-of-bounds access
  [SCSI] lpfc 8.3.42: Update lpfc version to driver version 8.3.42
  [SCSI] lpfc 8.3.42: Fixed issue of task management commands having a fixed timeout
  [SCSI] lpfc 8.3.42: Fixed inconsistent spin lock usage.
  [SCSI] lpfc 8.3.42: Fix driver's abort loop functionality to skip IOs already getting aborted
  [SCSI] lpfc 8.3.42: Fixed failure to allocate SCSI buffer on PPC64 platform for SLI4 devices
  [SCSI] lpfc 8.3.42: Fix WARN_ON when driver unloads
  [SCSI] lpfc 8.3.42: Avoided making pci bar ioremap call during dual-chute WQ/RQ pci bar selection
  [SCSI] lpfc 8.3.42: Fixed driver iocbq structure's iocb_flag field running out of space
  [SCSI] lpfc 8.3.42: Fix crash on driver load due to cpu affinity logic
  [SCSI] lpfc 8.3.42: Fixed logging format of setting driver sysfs attributes hard to interpret
  [SCSI] lpfc 8.3.42: Fixed back to back RSCNs discovery failure.
  [SCSI] lpfc 8.3.42: Fixed race condition between BSG I/O dispatch and timeout handling
  [SCSI] lpfc 8.3.42: Fixed function mode field defined too small for not recognizing dual-chute mode
  ...
2013-09-15 17:41:30 -04:00
Mike Miller e481cce8b0 [SCSI] hpsa: bump driver version to reflect changes
Changes the version of hpsa so we know something has changed. Please consider
this for inclusion.

Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-09-10 14:43:02 -07:00
Mike Miller 163dbcd89c [SCSI] hpsa: housekeeping patch for device_id and product arrays
This patch does a bit of housekeeping for hpsa. Change lowercase alpha hex
digits to uppercase for consistency within the driver. Also moves the P822se
in the tables to keep controllers of each family grouped together.

Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-09-10 14:38:56 -07:00
Mike Miller 1fd6c8e37c [SCSI] hpsa: add HP Smart Array Gen8 names
Add the marketing names for HP Smart Array Gen8 controllers. Also removes an
unused ID. Please consider this for inclusion.

Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-09-10 14:30:08 -07:00
Mike Miller 97b9f53d7d [SCSI] hpsa: add HP Smart Array Gen9 PCI ID's
This patch adds the PCI ID's for HP Smart Array Gen9 controllers. Please
consider this patch for inclusion.

Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-09-10 14:14:21 -07:00
Linus Torvalds 2e515bf096 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
 "The usual trivial updates all over the tree -- mostly typo fixes and
  documentation updates"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
  doc: Documentation/cputopology.txt fix typo
  treewide: Convert retrun typos to return
  Fix comment typo for init_cma_reserved_pageblock
  Documentation/trace: Correcting and extending tracepoint documentation
  mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
  power: Documentation: Update s2ram link
  doc: fix a typo in Documentation/00-INDEX
  Documentation/printk-formats.txt: No casts needed for u64/s64
  doc: Fix typo "is is" in Documentations
  treewide: Fix printks with 0x%#
  zram: doc fixes
  Documentation/kmemcheck: update kmemcheck documentation
  doc: documentation/hwspinlock.txt fix typo
  PM / Hibernate: add section for resume options
  doc: filesystems : Fix typo in Documentations/filesystems
  scsi/megaraid fixed several typos in comments
  ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
  treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
  page_isolation: Fix a comment typo in test_pages_isolated()
  doc: fix a typo about irq affinity
  ...
2013-09-06 09:36:28 -07:00
Joe Perches 9e03aa2f83 treewide: Convert retrun typos to return
Tyops should be fixed.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-09-04 12:26:36 +02:00
John Kacur 804a5cb526 [SCSI] hpsa: fix warning with smp_processor_id() in preemptible
section Signed-off-by: John Kacur <jkacur@redhat.com>

On a 3.6-rt (real-time patch) kernel we are seeing the following BUG
However, it appears to be relevant for non-realtime (mainline) as well.

[   49.688847] hpsa 0000:03:00.0: hpsa0: <0x323a> at IRQ 67 using DAC
[   49.749928] scsi0 : hpsa
[   49.784437] BUG: using smp_processor_id() in preemptible [00000000
00000000] code: kworker/u:0/6
[   49.784465] caller is enqueue_cmd_and_start_io+0x5a/0x100 [hpsa]
[   49.784468] Pid: 6, comm: kworker/u:0 Not tainted
3.6.11.5-rt37.52.el6rt.x86_64.debug #1
[   49.784471] Call Trace:
[   49.784512]  [<ffffffff812abe83>] debug_smp_processor_id+0x123/0x150
[   49.784520]  [<ffffffffa009043a>] enqueue_cmd_and_start_io+0x5a/0x100
[hpsa]
[   49.784529]  [<ffffffffa00905cb>]
hpsa_scsi_do_simple_cmd_core+0xeb/0x110 [hpsa]
[   49.784537]  [<ffffffff812b09c8>] ? swiotlb_dma_mapping_error+0x18/0x30
[   49.784544]  [<ffffffff812b09c8>] ? swiotlb_dma_mapping_error+0x18/0x30
[   49.784553]  [<ffffffffa0090701>]
hpsa_scsi_do_simple_cmd_with_retry+0x91/0x280 [hpsa]
[   49.784562]  [<ffffffffa0093558>]
hpsa_scsi_do_report_luns.clone.2+0xd8/0x130 [hpsa]
[   49.784571]  [<ffffffffa00935ea>]
hpsa_gather_lun_info.clone.3+0x3a/0x1a0 [hpsa]
[   49.784580]  [<ffffffffa00963df>] hpsa_update_scsi_devices+0x11f/0x4f0
[hpsa]
[   49.784592]  [<ffffffff81592019>] ? sub_preempt_count+0xa9/0xe0
[   49.784601]  [<ffffffffa00968ad>] hpsa_scan_start+0xfd/0x150 [hpsa]
[   49.784613]  [<ffffffff8158cba8>] ? rt_spin_lock_slowunlock+0x78/0x90
[   49.784626]  [<ffffffff813b04d7>] do_scsi_scan_host+0x37/0xa0
[   49.784632]  [<ffffffff813b05da>] do_scan_async+0x1a/0x30
[   49.784643]  [<ffffffff8107c4ab>] async_run_entry_fn+0x9b/0x1d0
[   49.784655]  [<ffffffff8106ae92>] process_one_work+0x1f2/0x620
[   49.784661]  [<ffffffff8106ae20>] ? process_one_work+0x180/0x620
[   49.784668]  [<ffffffff8106d4fe>] ? worker_thread+0x5e/0x3a0
[   49.784674]  [<ffffffff8107c410>] ? async_schedule+0x20/0x20
[   49.784681]  [<ffffffff8106d5d3>] worker_thread+0x133/0x3a0
[   49.784688]  [<ffffffff8106d4a0>] ? manage_workers+0x190/0x190
[   49.784696]  [<ffffffff81073236>] kthread+0xa6/0xb0
[   49.784707]  [<ffffffff815970a4>] kernel_thread_helper+0x4/0x10
[   49.784715]  [<ffffffff81082a7c>] ? finish_task_switch+0x8c/0x110
[   49.784721]  [<ffffffff8158e44b>] ? _raw_spin_unlock_irq+0x3b/0x70
[   49.784727]  [<ffffffff8158e85d>] ? retint_restore_args+0xe/0xe
[   49.784734]  [<ffffffff81073190>] ? kthreadd+0x1e0/0x1e0
[   49.784739]  [<ffffffff815970a0>] ? gs_change+0xb/0xb

-------------------

This is caused by
enqueue_cmd_and_start_io()->
        set_performant_mode()->
                smp_processor_id()
Which if you have debugging enabled calls debug_processor_id() and triggers the warning.

The code here is
 c->Header.ReplyQueue = smp_processor_id() % h->nreply_queues;

Since it is not critical that the code complete on the same processor,
but the cpu is a hint used in generating the ReplyQueue and will still work if
the cpu migrates or is preempted, it is safe to use the raw_smp_processor_id()
to surpress the false positve warning.

Signed-off-by: John Kacur <jkacur@redhat.com>
Acked-by: Stephen Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-08-26 18:53:50 +04:00
Tomas Henzl 1cdd3cf838 [SCSI] hpsa: remove unneeded variable
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-08-26 12:51:31 +04:00
Tomas Henzl 2cc5bfaf85 [SCSI] hpsa: fix a race in cmd_free/scsi_done
When the driver calls scsi_done and after that frees it's internal
preallocated memory it can happen that a new job is enqueud before
the memory is freed. The allocation fails and the message
"cmd_alloc returned NULL" is shown.
Patch below fixes it by moving cmd->scsi_done after cmd_free.

Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-08-26 12:51:31 +04:00
Stephen M. Cameron bcc48ffa4b [SCSI] hpsa: check for dma_mapping_error in hpsa_passthru ioctls
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-02-24 09:36:58 +00:00
Stephen M. Cameron c1f63c8fe8 [SCSI] hpsa: reorganize error handling in hpsa_passthru_ioctl
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-02-24 09:36:08 +00:00
Stephen M. Cameron e2bea6df32 [SCSI] hpsa: check for dma_mapping_error in hpsa_map_sg_chain_block
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-02-24 09:35:18 +00:00
Stephen M. Cameron a2dac136c4 [SCSI] hpsa: Check for dma_mapping_error for all code paths using fill_cmd
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-02-24 09:34:21 +00:00
Shuah Khan eceaae187d [SCSI] hpsa: Check for dma_mapping_error in hpsa_map_one
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2013-02-24 09:33:27 +00:00
Greg Kroah-Hartman 6f03979051 Drivers: scsi: remove __dev* attributes.
CONFIG_HOTPLUG is going away as an option.  As a result, the __dev*
markings need to be removed.

This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.

Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-03 15:57:01 -08:00
Linus Torvalds 3151367f87 SCSI for-linus on 20121002
This is a large set of updates, mostly for drivers (qla2xxx [including support
 for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa, be2iscsi, isci,
 lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas).  There's also a rework for tape
 adding virtually unlimited numbers of tape drives plus a set of dif fixes for
 sd and a fix for a live lock on hot remove of SCSI devices.
 
 This round includes a signed tag pull of isci-for-3.6
 
 Signed-off-by: James Bottomley <JBottomley@Parallels.com>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iQEcBAABAgAGBQJQaqCFAAoJEDeqqVYsXL0MKJ4IALg/Obnk0/fNvBUNIrh5zRmj
 r9UlXFJnlEDT03qRGdn8okgWMChbgaD1ZrwDTQnjNsabVQoTXI6oO6/uL2c8crpY
 BFBwJvkNJS99nbcZv10CpJ3K7ykmRnKlkYon12iknhGwdtU+XJ14Z4PUcZkI9jmg
 sBQQ6uNVWyosaONNE+k6o+dw6OTttJkzRX8e9in3thstxNTcG+h9iB1zZ/ETkSEj
 tD4MyOgDiPf8kPV2awQThQGpni9Tu3SQr5dEn/iUUktUjiYsDNQuyaAk+QzyhUU7
 D35iIJnIHlXTSTMQkrG4qpJHBvqPkWlYJzaOmheQryQ3vzp2C5Ly/hS9il45uIQ=
 =49u9
 -----END PGP SIGNATURE-----

Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull first round of SCSI updates from James Bottomley:
 "This is a large set of updates, mostly for drivers (qla2xxx [including
  support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa,
  be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas).

  There's also a rework for tape adding virtually unlimited numbers of
  tape drives plus a set of dif fixes for sd and a fix for a live lock
  on hot remove of SCSI devices.

  This round includes a signed tag pull of isci-for-3.6

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI
helper function use in a function that was removed by this pull.

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits)
  [SCSI] st: remove st_mutex
  [SCSI] sd: Ensure we correctly disable devices with unknown protection type
  [SCSI] hpsa: gen8plus Smart Array IDs
  [SCSI] qla4xxx: Update driver version to 5.03.00-k1
  [SCSI] qla4xxx: Disable generating pause frames for ISP83XX
  [SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX
  [SCSI] qla4xxx: IDC implementation for Loopback
  [SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx
  [SCSI] qla4xxx: Fix panic while rmmod
  [SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails
  [SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX
  [SCSI] qla4xxx: Update idc reg in case of PCI AER
  [SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery
  [SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX
  [SCSI] qla4xxx: Print correct IDC version
  [SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW
  [SCSI] scsi_dh_alua: Enable STPG for unavailable ports
  [SCSI] scsi_remove_target: fix softlockup regression on hot remove
  [SCSI] ibmvscsi: Fix host config length field overflow
  [SCSI] ibmvscsi: Remove backend abstraction
  ...
2012-10-02 19:01:32 -07:00
Mike Miller fe0c9610bb [SCSI] hpsa: gen8plus Smart Array IDs
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:52:50 +04:00
Stephen M. Cameron 256d0eaac8 [SCSI] hpsa: fix handling of protocol error
If a command status of CMD_PROTOCOL_ERR is received, this
information should be conveyed to the SCSI mid layer, not
dropped on the floor.  CMD_PROTOCOL_ERR may be received
from the Smart Array for any commands destined for an external
RAID controller such as a P2000, or commands destined for tape
drives or CD/DVD-ROM drives, if for instance a cable is
disconnected.  This mostly affects multipath configurations, as
disconnecting a cable on a non-multipath configuration is not
going to do anything good regardless of whether CMD_PROTOCOL_ERR
is handled correctly or not.  Not handling CMD_PROTOCOL_ERR
correctly in a multipath configaration involving external RAID
controllers may cause data corruption, so this is quite a serious
bug.  This bug should not normally cause a problem for direct
attached disk storage.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-18 12:29:30 +01:00
Stephen M. Cameron 088ba34c92 [SCSI] hpsa: use ioremap_nocache instead of ioremap
I think ioremap() ends up being equivalent to ioremap_nocache
by default, but we should signal our intent that these mappings
should be non-cacheable.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-14 11:51:50 +01:00
Stephen M. Cameron d6ebd0f758 [SCSI] hpsa: fix incorrect abort diagnostic message
In the abort handler, when asked to abort a command which
is not known to the driver, SUCCESS is returned, but the
diagnostic message incorrectly indicates the abort failed.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-14 11:51:11 +01:00
Stephen M. Cameron 21e89afd32 [SCSI] hpsa: Use LUN reset instead of target reset
It turns out Smart Array logical drives do not support target
reset and when the target reset fails, the logical drive will
be taken off line.  Symptoms look like this:

hpsa 0000:03:00.0: Abort request on C1:B0:T0:L0
hpsa 0000:03:00.0: resetting device 1:0:0:0
hpsa 0000:03:00.0: cp ffff880037c56000 is reported invalid (probably means target device no longer present)
hpsa 0000:03:00.0: resetting device failed.
sd 1:0:0:0: Device offlined - not ready after error recovery
sd 1:0:0:0: rejecting I/O to offline device
EXT3-fs error (device sdb1): read_block_bitmap:

LUN reset is supported though, and is what we should be using.
Target reset is also disruptive in shared SAS situations,
for example, an external MSA1210m which does support target
reset attached to Smart Arrays in multiple hosts -- a target
reset from one host is disruptive to other hosts as all LUNs
on the target will be reset and will abort all outstanding i/os
back to all the attached hosts.  So we should use LUN reset,
not target reset.

Tested this with Smart Array logical drives and with tape drives.
Not sure how this bug survived since 2009, except it must be very
rare for a Smart Array to require more than 30s to complete a request.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-14 11:48:38 +01:00
Stephen M. Cameron e85c597469 [SCSI] hpsa: dial down lockup detection during firmware flash
Dial back the aggressiveness of the controller lockup detection thread.
Currently it will declare the controller to be locked up if it goes
for 10 seconds with no interrupts and no change in the heartbeat
register.  Dial back this to 30 seconds with no heartbeat change, and
also snoop the ioctl path and if a firmware flash command is detected,
dial it back further to 4 minutes until the firmware flash command
completes.  The reason for this is that during the firmware flash
operation, the controller apparently doesn't update the heartbeat
register as frequently as it is supposed to, and we can get a false
positive.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-10 09:19:39 +01:00
Mike Miller d82357eaaa [SCSI] hpsa: add new RAID level "1(ADM)"
Signed-off-by: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-10 09:18:24 +01:00
Stephen M. Cameron 0097f0f45a [SCSI] hpsa: factor out hpsa_free_irqs_and_disable_msix
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-10 09:17:51 +01:00
Matt Gates e16a33adc0 [SCSI] hpsa: refine interrupt handler locking for greater concurrency
Use spinlocks with finer granularity in the submission and
completion paths to allow concurrent execution for multiple
reply queues.  In particular, do not hold a spin lock while
submitting a request to the device, nor during most of the
interrupt handler.

Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-10 09:17:26 +01:00
Matt Gates 254f796b9f [SCSI] hpsa: use multiple reply queues
Smart Arrays can support multiple reply queues onto which command
completions may be deposited.  It can help performance quite a bit
to arrange for command completions to be processed on the same CPU
from which they were submitted to increase the likelihood of cache
hits.

Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-10 09:16:25 +01:00
Stephen M. Cameron 1d94f94d89 [SCSI] hpsa: factor out tail calls to next_command() in process_(non)indexed_cmd()
This is in order to smooth the way for upcoming changes to allow use of
multiple reply queues for command completions.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-10 09:15:46 +01:00
Stephen M. Cameron 6cba3f1972 [SCSI] hpsa: do aborts two ways
When aborting a command, the tag is supposed to be
specified as 64-bit little endian.  However, some smart
arrays expect the tag of the command to be aborted to be
specified in a strange byte order.  How to tell which sort
of Smart Array firmware we're dealing with is not obvious.
However, because of the way we construct our tags, the values
of any outstanding tag when specified with the "strange" byte
order will not collide with the value specified in the correct
order.  That means we can safely attempt the abort both ways.

Signed-off-by: Stephen M. Cameron <stephenmcameron@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-10 09:15:16 +01:00
Stephen M. Cameron 75167d2cc7 [SCSI] hpsa: add abort error handler function
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-10 09:14:29 +01:00
Stephen M. Cameron 5a3d16f51e [SCSI] hpsa: remove unused parameter from finish_cmd
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-10 09:13:55 +01:00